Viewsonic VX924-1 Schematic

Page 1
Service Manual
ViewSonic VX9241
Model No. VS10162
19Color TFT LCD Display
ViewSonic
(VX912_SM. 1a May 2005)
381 Brea Canyon Road, Walnut, California 91789 USA - (800) 888-8583
Page 2
Copyright reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language or computer language, in any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise, without the prior written permission of ViewSonic Corporation.
Disclaimer
ViewSonic makes no representations or warranties, either expressed or implied, with respect to the contents hereof and specifically disclaims any warranty of merchantability or fitness for any particular purpose. Further, ViewSonic reserves the right to revise this publication and to make changes from time to time in the contents hereof without obligation of ViewSonic to notify any person of such revision or changes.
Trademarks
Optiquest is a registered trademark of ViewSonic Corporation. ViewSonic is a registered trademark of ViewSonic Corporation. All other trademarks used within this document are the property of their respective owners.
2005 by ViewSonic Corporation. All rights reserved. No part of this publication may be
¤
ECR Number
1a
05/09/05
Revision History
Description of Changes
Initial Release
EditorRevision SM Editing Date
A. Lu
ViewSonic Corporation Confidential
i
-
Do Not Copy VX924
Page 3
TABLE OF CONTENTS
1. Precautions and Safety Notices
2. Specification
3. Front Panel Function Control Description
4. Circuit Description
5. Adjustment Procedure
6. Troubleshooting Flow Chart
7. Recommended Spare Parts List
8. Exploded Diagram and Spare Parts List
9. Block Diagram
10. Schematic Diagrams
11. PCB Layout Diagrams
1
5
11 17
27 49
55 58 68 70
78
ViewSonic Corporation Confidential
ii
-
Do Not Copy VX924
Page 4
1. Precautions and Safety Notices
1. Appropriate Operation
(1) Turn off the product before cleaning. (2) Use only a dry soft cloth when cleaning the LCD panel surface. (3) Use a soft cloth soaked with mild detergent to clean the display housing. (4) Use only a high quality, safety approved AC/DC power cord. (5) Disconnect the power plug from the AC outlet if the product will not be used for a long period of time. (6) If smoke, abnormal noise, or strange odor is present, immediately switch the LCD display off. (7) Do not touch the LCD panel surface with sharp or hard objects. (8) Do not place heavy objects on the LCD display, video cable, or power cord. (9) Do not use abrasive cleaners, waxes or solvents for your cleaning. (10) Do not operate the product under the following conditions:
- Extremely hot, cold or humid environment.
- Areas containing excessive dust and dirt.
- Near any appliance generating a strong magnetic field.
- In direct sunlight.
2. Caution
No modification of any circuit should be attempted. Service work should only be performed after you are thoroughly familiar
with all of the following safety checks and servicing guidelines.
3. Safety Check
Care should be taken while servicing this LCD display. Because of the high voltage used in the inverter circuit, the voltage is
exposed in such areas as the associated transformer circuits.
4. LCD Module Handling Precautions
4.1 Handling Precautions
(1) Since front polarizer is easily damaged, pay attention not to scratch it. (2) Be sure to turn off power supply when connecting or disconnecting input connector. (3) Wipe off water drops immediately. Long contact with water may cause discoloration or spots. (4) When the panel surface is soiled, wipe it with absorbent cotton or other soft cloth. (5) Since the panel is made of glass, it may break or crack if dropped or bumped on hard surface. (6) Since CMOS LSI is used in this module, take care of static electricity and ensure human earth when handling. (7) Do not open or modify the Module Assembly. (8) Do not press the reflector sheet at the back of the module in any direction. (9) In the event that a Module must be put back into the packing container slot after it was taken out of the
container, do not press the center of the CCFL Reflector edge. Instead, press at the far ends of the CFL Reflector edge softly. Otherwise the TFT Module may be damaged.
(10) At the insertion or removal of the Signal Interface Connector, be sure not to rotate or tilt the Interface
Connector of the TFT Module.
ViewSonic Corporation Confidential
1
-
Do Not Copy VX924
Page 5
(11) After installation of the TFT Module into an enclosure (LCD monitor housing, for example), do not twist or
bend the TFT Module even momentarily. When designing the enclosure, it should be taken into consideration that no bending/twisting forces may be applied to the TFT Module from outside. Otherwise the TFT Module may be damaged.
(12) The cold cathode fluorescent lamp in the LCD contains a small amount of mercury. Please follow local
ordinances or regulations for disposal.
(13) The LCD module contains a small amount of materials having no flammability grade. The LCD module
should be supplied with power that complies with the requirements of Limited Power Source (IEC60950 or UL1950), or an exemption should be applied for.
(14) The LCD module is designed so that the CCFL in it is supplied by a Limited Current Circuit (IEC60950
or UL1950). Do not connect the CCFL to a Hazardous Voltage Circuit.
ViewSonic Corporation Confidential
2
-
Do Not Copy VX924
Page 6
Correct methods : Incorrect Methods :
Only touch the metal frame of the panel or the front cover of the monitor. Do not touch the surface of the polarizer .
If the surface of the panel is pressed by fingers, this may cause "MURA."
Take out the monitor by grasping the cushion. If the monitor is removed by grasping the LCD
panel, that may cause "MURA."
ViewSonic Corporation Confidential
3
-
Do Not Copy VX924
Page 7
Correct Methods : Incorrect Methods :
Place the monitor on a clean & soft foam pad . If the monitor is placed on foreign objects,
that could scratch the surface of the panel.
ViewSonic Corporation Confidential
4
-
Do Not Copy VX924
Page 8
2. Specification
z GENERAL specification
Test Resolution & Frequency 1280x1024 @ 60Hz
Test Image Size Full Size
Contrast and Brightness Controls
Factory Default:
Contrast = 70%, Brightness = 100%
z VIDEO INTERFACE
Analog Input Connector DB-15 (Analog), refer the appendix A
Digital Input Connector DVI-I (Digital), refer the appendix B
Default Input Connector Defaults to the first detected input
Video Cable Strain Relief Equal to twice the weight of the monitor for five minutes
Video Cable Connector DB-15 Pin out Compliant DDC 1/2B
1. Video RGB (Analog)
Video Signals
Separate, Composite, and Sync on Green
2. TMDS (Digital)
Video Impedance 75 Ohms (Analog), 100 Ohms (Digital)
Maximum PC Video Signal 950 mV with no damage to monitor
Maximum Mac Video Signal 1250 mV with no damage to monitor
Sync Signals LVDS
DDC 1/2B Compliant with Revision 1.3
Sync Compatibility Separate Sync, Composite Sync, SOG
Shall be compatible with all PC type computers,
Video Compatibility
Macintosh computers, and after market video cards
640 x 350*, 640 x 480, 720 x 400* (640 x 400*), 800 x
600, 832 x 624, 1024 x 768, 1152 x 864, 1152 x 870,
1280 x 720, 1280 x 960, 1280 x 1024
Resolution Compatibility
* The image vertical size might not be full screen.
But the image vertical position should be at the center.
Exclusions Not compatible with interlaced video
ViewSonic Corporation Confidential
5
-
Do Not Copy VX924
Page 9
z POWER SUPPLY
Internal Power Supply Part Number: FSP035-1PI01
Input Voltage Range 90 TO 264 VAC
Input Frequency Range 47.5 TO 63 HERTZ
Short Circuit Protection Output can be shorted without damage
Over Current Protection 3.5 A typical at 12.0 VDC ( Protect when short circuit )
Leakage Current 0.75mA (Max) at 264VAC / 50Hz
EFFICIENCY 77 % typical at 115VAC Full Load
Fuse Internal and not user replaceable
Power Dissipation 35 Watts (typ)
Max Input AC Current 1.2 Arms @ 90VAC, 0.7 Arms @265VAC
INRUSH CURRENT (COLD START) 60 A @ 115VAC
Shall start and function properly when under full load,
Power Supply Cold Start
Power Supply Transient Immunity
Power Supply Line Surge Immunity
Power Supply Missing Cycle Immunity
Power Supply Acoustics
with all combinations of input voltage, input frequency,
and operating temperature
Shall be able to withstand an ANSI/IEEE C62.41-1980
2000V 200 ampere ring wave transient test with no
damage
Shall be able to withstand 1.5 times nominal line voltage
for one cycle with no damage
Shall be able to function properly, without reset or visible
screen artifacts, when ½ cycle of AC power is randomly
missing at nominal input
The power supply shall not produce audible noise that
would be detectable by the user. Audible shall defined
to be in compliance with ISO 7779 (DIN EN27779:1991)
Noise measurements of machines acoustics. Power
Switch noise shall not be considered
Separate 3-prong NEMA 5-15P type plug. Length =
US Type Power Cable
1.8m. Connects to display.
Color = Black
Schuko CEE7-7 type plug.
European Type Power Cable
Length = 1.8m, Connects to display.
Color = Black
ViewSonic Corporation Confidential
6
-
Do Not Copy VX924
Page 10
Separate 3-prong type plug.
CCC Type Power Cable
Length = 1.8m. Connects to display.
Color = Black
Separate 2-prong NEMA 1-15P type plug. Length =
PSE Type Power Cable
1.8m. Connects to display.
Color = Black
VESA DPMS Signaling
Power Saving Operation(Method)
ON Mode < 40 W (Max) / 35 W (Typ)
On Mode < 40 W (Max) / 35 W (Typ)
Power Consumption
Saving Mode < 2 W, Off Mode < 1 W
Recovery Time On Mode = N/A, Active Off < 3 sec
z ELECTRICAL REQUIREMENT
Horizontal / Vertical Frequency
Horizontal Frequency 30 – 82 KHZ
Vertical Refresh Rate 50 – 75 HZ
Maximum Pixel Clock 135 MHz
Sync Polarity Independent of sync polarity.
z Timing Table
Item Timing Analog Digital
1 640 x 350 @ 70Hz, 31.5kHz Yes Yes
2 640 x 400 @ 60Hz, 31.5kHz Yes Yes
3 640 x 400 @ 70Hz, 31.5kHz Yes Yes
4 640 x 480 @ 50Hz, 24.7kHz Yes No
5 640 x 480 @ 60Hz, 31.5kHz Yes Yes
6 640 x 480 @ 67Hz, 35.0kHz Yes Yes
7 640 x 480 @ 72Hz, 37.9kHz Yes Yes
8 640 x 480 @ 75Hz, 37.5kHz Yes Yes
9 640 x 480 @ 85Hz, 43.27kHz No No
10 720 x 400 @ 70Hz, 31.5kHz Yes Yes
11 800 x 600 @ 56Hz, 35.1kHz Yes Yes
12 800 x 600 @ 60Hz, 37.9kHz Yes Yes
13 800 x 600 @ 75Hz, 46.9kHz Yes Yes
14 800 x 600 @ 72Hz, 48.1kHz Yes Yes
15 800 x 600 @ 85Hz, 53.7kHz No No
16 832 x 624 @ 75Hz, 49.7kHz Yes Yes
ViewSonic Corporation Confidential
7
-
Do Not Copy VX924
Page 11
17 1024 x 768 @ 60Hz, 48.4kHz Yes Yes
18 1024 x 768 @ 70Hz, 56.5kHz Yes Yes
19 1024 x 768 @ 72Hz, 58.1kHz Yes Yes
20 1024 x 768 @ 75Hz, 60.0kHz Yes Yes
21 1024 x 768 @ 85Hz, 68.67kHz No No
22 1152 x 864 @ 75Hz, 67.5kHz Yes Yes
23 1152 x 870 @ 75Hz, 68.7kHz Yes Yes
24 1280 x 1024 @ 60Hz, 63.4kHz Yes Yes
25 1280 x 1024 @ 75Hz, 79.97kHz Yes Yes
26 1280x 720 @ 60Hz, 45kHz (HDTV) Yes Yes
z Primary Presets
1280x1024 @ 60Hz
z User Presets
Number of User Presets (recognized timings) Available: 10 presets total in FIFO configuration
z Changing Modes
- Maximum Mode Change Blank Time for image stability : 3 seconds (Max), excluding “Auto Adjust” time
- Under DOS mode (640 x 350, 720 x 400 & 640 x 400), it should recall factory setting when execute “Auto Adjust”
- The monitor needs to do “Auto Adjust” the first time when a new mode is detected
(See section “0-Touch™ Function Actions”)
ViewSonic Corporation Confidential
8
-
Do Not Copy VX924
Page 12
z TFT LCD PANEL
st
1
Source Panel
Model number AUO M190EN04 V5
Type TN type with LVDS interface
Active Size 376.32 (H) x 301.06 (V)
Pixel Arrangement RGB Vertical Stripe
Pixel Pitch 0.294 mm
GLASS TREATMENT Anti Glare (Hard coating 3H)
# OF BACKLIGHTS 4 CCFL edge-light (2 top / 2 bottom)
BACKLIGHT LIFE 50,000 Hours (Min)
Luminance (5-point) –
Condition:
275 cd/m2 (Typ after 30 minute warm up)
215 cd/m2 (Min after 30 minute warm up)
CT = 6500K, Contrast = Max, Brightness = Max
Brightness Uniformity
70% Entire Area (min)
Contrast Ratio 550:1 (typ), 350:1 (min)
Color Depth 16.2 million colors (6 bits + 2 bits FRC)
Viewing Angle (Horizontal) @ CR>10
Typical: 140º
Minimum: 130º
Viewing Angle (Vertical) @ CR>10
Typical: 135º
Minimum: 125º
Total = 4.8ms (black – white)
Response Time
10%-90% @ Ta=25°C
(Tr=3.4ms, Tf=1.4ms)
Total = 4.0ms (gray – gray)
Panel Defects Please see Panel Quality Specifications.
ViewSonic Corporation Confidential
9
-
Do Not Copy VX924
Page 13
z MECHANICAL
Dimension (Desktop)
Width 431 mm (17 inch)
Height 468 mm (18.4 inch)
Depth 201 mm (7.9 inch)
Monitor Weight 6.7 Kg (14.8 lbs)
z Dimension (Head Only / Wall Mount)
Width 431 mm (17 inch)
Height 370 mm (14.6 inch)
Depth 66 mm (2.6 inch)
Monitor Weight 5.3 Kg (11.7 lbs)
z Ergonomics
Tilt Up From 0º up to 20º
Tilt Down From 0º down to -3º ~ -5 º
z ENVIRONMENTAL
- Operating Temperature : 0°C to +40°C
- Storage Temperature : -20°C to +60°C
- Operating Relative Humidity : 20% to 90% RH Non-Condensing
- Storage Relative Humidity : 5% to 90% RH Non-Condensing
- Operating Altitude : 0 to +3,000 meters
- Storage Altitude : 0 to +12,000 meters
ViewSonic Corporation Confidential
10
-
Do Not Copy VX924
Page 14
3. Front Panel Function Control Description
Adjusting the Screen Image
Use the buttons on the front control panel to display and adjust the OSD controls which display on the screen. The OSD controls are explained at the top of the next page and are defined in
“Main Menu Controls” on page 13.
Main Menu
with OSD controls
Front Control Panel
shown below in detail
Displays the Main
Menu or exits the
control screen
and saves
adjustments.
Scrolls through menu options and adjusts the displayed control.
Also a shortcut to display the Contrast adjustment control screen.
Displays the control screen for the highlighted control.
Also toggles between two controls on some screens.
Also a shortcut to toggle analog and digital connection.
Power light Green = ON Orange = Power Saving
Power On/Off
ViewSonic Corporation Confidential
11
-
Do Not Copy VX924
Page 15
Do the following to adjust the display setting:
1. To display the Main Menu, press button [1].
NOTE: All OSD menus and adjustment screens disappear automatically after about 30
seconds. This is adjustable through the OSD timeout setting in the setup menu.
2. To select a setting to be adjusted, pressSorTto scroll up or down the Main Menu.
3. After the desired control is selected, press button [2]. A control screen like the one shown
below appears.
The line at the bottom of the screen tells you what you can do next: Exit or select the Brightness control.
4. To adjust the setting, press the upSor downTbuttons.
5. To save the adjustments and exit the menu, press button [1] twice.
The following tips may help you optimize your display:
• Adjust your computer's graphics card so that it outputs a 1280 x 1024 @ 60Hz video signal to the LCD display. (Look for instructions on “changing the refresh rate” in your graphic card's user guide.)
• If necessary, make small adjustments using H. POSITION and V. POSITION until the screen image is completely visible. (The black border around the edge of the screen should barely touch the illuminated “active area” of the LCD display.)
ViewSonic Corporation Confidential
12
-
Do Not Copy VX924
Page 16
Main Menu Controls
Adjust the menu items shown below by using the upSand downTbuttons.
Control Explanation
Auto Image Adjust automatically sizes, centers, and fine tunes the video signal to eliminate waviness and distortion.
NOTE:
1. Auto Image Adjust works with most common video cards. If this function
does not work on your LCD display, then lower the video refresh rate to 60 Hz and set the resolution to its pre-set value.
2. The Auto Image Adjust and most Manual Image Adjust functions are not available for DVI input.
Contrast adjusts the difference between the image background (black level) and the foreground (white level).
Brightness adjusts background black level of the screen image.
Input Select allows you to toggle between an analog and a digital signal.
Color Adjust provides several color adjustment modes: preset color
temperatures and User Color which allows you to adjust red (R), green (G), and blue (B) separately. The factory setting for this product is 6500K (6500 Kelvin).
sRGB-sRGB is quickly becoming the industry standard for color management, with support being included in many of the latest applications. Enabling this setting allows the LCD display to more accurately display colors the way they were originally intended. Enabling the sRGB setting will cause the Contrast and Brightness adjustments to be disabled.
9300K-Adds blue to the screen image for cooler white (used in most office settings with fluorescent lighting).
ViewSonic Corporation Confidential
13
-
Do Not Copy VX924
Page 17
Control Explanation
6500K-Adds red to the screen image for warmer white and richer red.
5400K-Adds green to the screen image for a darker color.
User Color Individual adjustments for red (R), green (G), and blue (B).
1. To select color (R, G or B) press button [2].
2. To adjust selected color, pressSorT.
Important: If you select RECALL from the Main Menu when the product is set
to a Preset Timing Mode, colors return to the 6500K factory preset.
Information displays the timing mode (video signal input) coming from the graphics card in your computer, the LCD model number, the serial number, and the ViewSonic® website URL. See your graphics card’s user guide for instructions on changing the resolution and refresh rate (vertical frequency).
NOTE: VESA 1280 x 1024 @ 60Hz (recommended) means that the resolution is 1280 x 1024 and the refresh rate is 60 Hertz.
Manual Image Adjust displays the Manual Image Adjust menu.
ViewSonic Corporation Confidential
14
-
Do Not Copy VX924
Page 18
Control Explanation
The Manual Image Adjust controls are explained below:
H./V. Position (Horizontal/Vertical Position) moves the screen image left or
right and up or down.
H. Size (Horizontal Size) adjusts the width of the screen image.
Fine Tune sharpens the focus by aligning the text and/or graphic characters.
Sharpness adjusts the clarity and focus of the screen image.
Setup menu displays the menu shown below:
The Setup Menu controls are explained below:
Language allows you to choose the language used in the menus and control
screens.
Resolution Notice displays the Resolution Notice menu shown below.
Resolution Notice advises the optimal resolution to use.
OSD Position allows you to move the on-screen display menus and control
screens.
ViewSonic Corporation Confidential
15
-
Do Not Copy VX924
Page 19
Control Explanation
OSD Timeout sets the length of time the on-screen display screen is displayed. For example, with a “15 second” setting, if a control is not pushed within 15 seconds, the display screen disappears.
OSD Background allows you to turn the On-Screen Display background On or Off.
Memory Recall returns the adjustments back to factory settings if the display is operating in a factory Preset Timing Mode listed in the Specifications of this manual.
Exception: This control does not affect changes made with the User Color control, Language or Power Lock setting.
ViewSonic Corporation Confidential
16
-
Do Not Copy VX924
Page 20
4. Circuit Description
1. Outline
1.1 Buttons on the front panel: Power On/Off button, button 2 (ENTER / INPUT SELECT), up arrow
button, down arrow button, button 1 (MENU).
The D-sub 15-pin connector, DVI-I connector and AC-IN jack are located on the back side of the cabinet.
1.2
1.3 The OSD menu includes the following functions:
Auto Image Adjust (only active under analog input) Contrast/Brightness Audio Adjust Color Adjust Information Manual Image Adjust Setup Menu Memory Recall
Contrast and Brightness can be directly controlled with the UP / DOWN buttons.
1.4
2. Connectors
AC Socket: CEE22 type connector
2.1
2.2 Video signal connector for analog input: 15P Mini D-Sub
16
1
11
6
2
7
3
8
4
9
12
13
14
15
CN6
5
10
DB15HD
17
PIN MNEMONIC SIGNAL 1 RV Red Video 2 GV Green Video 3 BV Blue Video 4 NC None 5 GND Ground(DDC return) 6 RG Red GND 7 GG Green GND 8 BG Blue GND 9 +5V +5V (for DDC) 10 SG Sync GND 11 NC None 12 SDA DDC Data 13 HS Horizontal Sync 14 VS Vertical Sync 15 SCL DDC Clock
ViewSonic Corporation Confidential
17
-
Do Not Copy VX924
Page 21
2.3
Video signal connector for digital input: 24pin DVI-D connector
CN9
1
RX2-
2
RX2+
3
GND
4
RX4-
5
RX4+
6
SCL
7
SDA
8
VS
9
RX1-
10
RX1+
11
GND
12
RX3-
13
RX3+
14
5V
15
GND
16
HP
17
RX0-
18
RX0+
19
GND
20
RX5-
21
RX5+
22
GND
23
RXC+
24
RXC-
3. Electrical Specifications
DVI-D
3.1 Standard conditions
Pin No. Signal Name Description
1 RX2- TMDS negative differential input, channel 2 2 RX2+ TMDS positive differential input, channel 2 3 GND Logic Ground 4 RX4- Reserved. No connection 5 RX4+ Reserved. No connection 6 SCL DDC2B Clock 7 SDA DDC2B Data 8 VS Reserved. No connection
9 RX1- TMDS negative differential input, channel 1 10 RX1+ TMDS positive differential input, channel 1 11 GND Logic Ground 12 RX3- Reserved. No connection 13 RX3+ Reserved. No connection 14 +5V Power 15 GND Logic Ground 16 HP SENSE Pin, Pull High 17 RX0- TMDS negative differential input, channel 0 18 RX0+ TMDS positive differential input, channel 0 19 GND Logic Ground 20 RX5- Reserved. No connection 21 RX5+ Reserved. No connection 22 GND Logic Ground 23 RXC+ TMDS positive differential input, reference clock 24 RXC- TMDS negative differential input, reference clock
Display Area Video Signal Contrast Brightness Ambient Input Warming up Display
404.2 x 330.0 mm
0.7Vpp
Max.
Max. 20 +/- 5 °C
AC
> 30 min
1280 x 1024
ViewSonic Corporation Confidential
18
-
Do Not Copy VX924
Page 22
3.2 Power
3.2.1 Power supply
Input voltage 100~240Vac Power frequency 50~60Hz
Input current Inrush current
Power consumption 35W(typical);40Watts(Max)
3.2.2 Power Management
State Power Indicator
On 35Watts Green Standby < 1Watts Amber Off <1Watts Off
<1.5A RMS @90V AC
<0.8A RMS @180V AC
50A(Max) at 120Vac(cold start)
3.3 Acceptable timing
This LCD display can automatically detect and display input signals whose timing falls within the
following limits.
Horizontal: Sync frequency: 30~82 kHz Vertical: Sync frequency: 56~75Hz
3.4 Signal level and input impedance
3.4.1 Video signal level: 0.7Vp-p
3.4.2 Sync signal level - H/V separate: TTL level
3.4.3 Input impedance
Analog video input: 75 ohm Digital video input: 100 ohm Sync input: > 1 k ohm Audio input: 10K ohm
4. Signal Cable: Signal cable with Mini D-Sub 15P connectors at both ends. Length: 1.8 meter.
ViewSonic Corporation Confidential
19
-
Do Not Copy VX924
Page 23
5. EDID data
AUO
Analog EDID
128 BYTES OF EDID CODE:
0 1 2 3 4 5 6 7 8 9
________________________________________
0 | 00 FF FF FF FF FF FF 00 5A 63
10 | 1C 0F 01 01 01 01 01 0F 01 03
20 | 0E 26 1E 78 2E 68 75 A2 5A 49
30 | 9F 23 13 50 54 BF EF 80 81 80
40 | 71 4F 61 59 45 59 31 59 01 01
50 | 01 01 01 01 30 2A 00 98 51 00
60 | 2A 40 30 70 13 00 78 2D 11 00
70 | 00 1E 00 00 00 FF 00 50 53 33
80 | 30 35 30 31 30 30 30 30 31 0A
90 | 00 00 00 FD 00 32 55 1E 52 0E
100 | 00 0A 20 20 20 20 20 20 00 00
110 | 00 FC 00 56 58 39 32 34 0A 20
120 | 20 20 20 20 20 20 00 D3 __________ _______________________________________
(08-09) ID Manufacturer Name = VSC (11-10) P roduct ID Code = 0F1C (12-15) Last 5 Digits of Serial Number = Not Used (16) Week of Manufacture = 01 (17) Year of Manufacture = 2005 (10-17) Complete Serial Number = See Descriptor Block (18) EDID Version Number = 1 (19) EDID Revision Number = 3 (20) VIDEO INPUT DEFINITION:
Analog Signal
0.700, 0.300 (1.000 Vp-p)
Separate Syncs, Composite Sync, Sync on Green
(21) Maximum Horizontal Image Size = 380 mm (22) Maximum Vertical Image Size = 300 mm (23) Display Gamma = 2.20 (24) Power Management and Supported Feature(s):
Active Off/Very Low Power, Standard Default Color Space,
Preferred Timing Mode
Display Type = R/G/B Color
(25-34) CHROMA INFO:
Red X - 0.634 Green X - 0.287 Blue X - 0.138 White X - 0.313
Red Y - 0.354 Green Y - 0.621 Blue Y - 0.077 White Y - 0.329
(35) ESTABLISHED TIMING I:
720 X 400 @ 70Hz (IBM,VGA)
640 X 480 @ 60Hz (IBM,VGA)
640 X 480 @ 67Hz (Apple,Mac II)
640 X 480 @ 72Hz (VESA)
640 X 480 @ 75Hz (VESA)
800 X 600 @ 56Hz (VESA)
800 X 600 @ 60Hz (VESA)
ViewSonic Corporation Confidential
20
-
Do Not Copy VX924
Page 24
(36) ESTABLISHED TIMING II:
800 X 600 @ 72Hz (VESA)
800 X 600 @ 75Hz (VESA)
832 X 624 @ 75Hz (Apple,Mac II)
1024 X 768 @ 60Hz (VESA)
1024 X 768 @ 70Hz (VESA)
1024 X 768 @ 75Hz (VESA)
1280 X 1024 @ 75Hz (VESA)
(37) Manufacturer's Reserved Timing:
1152 X 870 @ 75Hz (Apple,Mac II)
(38-53) Standard Timing Identification:
1280 X 1024 @60Hz
1152 X 864 @75Hz
1024 X 768 @85Hz
800 X 600 @85Hz
640 X 480 @85Hz
Not Used
Not Used
Not Used ______________________________________________________________________
(54-71) Detailed Timing / Descriptor Block 1:
______________________________________________________________________
Horizontal:
Vertical:
Digital Separate, Horizontal Polarity (+) Vertical Polarity (+) ______________________________________________________________________
(72-89) Detailed Timing / Descriptor Block 2:
Monitor Serial Number:
PS3050100001 ______________________________________________________________________
(90-107) Detailed Timing / Descriptor Block 3:
______________________________________________________________________
(108-125) Detailed Timing / Descriptor Block 4:
Monitor Name:
(126) No Extension EDID Block(s)
ViewSonic Corporation Confidential
(127) CheckSum OK
1280x1024 Pixel Clock: 108.00 MHz
Horizontal Image Size: 376 mm Vertical Image Size: 301 mm
Refreshed Mode: Non-Interlaced Normal Display - No Stereo
Active Time: 1280 pixels Blanking Time: 408 pixels
Sync Offset: 48 pixels Sync Pulse Width: 112 pixels
Border: 0 pixels Frequency: 63.98 KHz
Active Time: 1024 lines Blanking Time: 42 lines
Sync Offset: 1 lines Sync Pulse Width: 3 lines
Border: 0 lines Frequency: 60.02 Hz
Monitor Range Limits:
Min Vertical Freq - 50 Hz
Max Vertical Freq - 85 Hz
Min Horiz. Freq - 30 KHz
Max Horiz. Freq - 82 KHz
Pixel Clock - 140 MHz
Secondary GTF - Not Supported
VX924
21
-
Do Not Copy VX924
Page 25
Digital EDID
128 BYTES OF EDID CODE:
0 1 2 3 4 5 6 7 8 9
________________________________________
0 | 00 FF FF FF FF FF FF 00 5A 63
10 | 1C 0F 01 01 01 01 01 0F 01 03
20 | 80 26 1E 78 2E 68 75 A2 5A 49
30 | 9F 23 13 50 54 BF EF 80 81 80
40 | 71 4F 61 59 45 59 31 59 31 0A
50 | 01 01 01 01 30 2A 00 98 51 00
60 | 2A 40 30 70 13 00 78 2D 11 00
70 | 00 1E 00 00 00 FF 00 50 53 33
80 | 30 35 30 31 30 30 30 30 31 0A
90 | 00 00 00 FD 00 32 55 1E 52 0E
100 | 00 0A 20 20 20 20 20 20 00 00
110 | 00 FC 00 56 58 39 32 34 0A 20
120 | 20 20 20 20 20 20 00 28
_________________________________________________
(08-09) ID Manufacturer Name = VSC (11-10) Product ID Code = 0F1C (12-15) Last 5 Digits of Serial Number = Not Used (16) Week of Manufacture = 01 (17) Year of Manufacture = 2005 (10-17) Complete Serial Number = See Descriptor Block (18) EDID Version Number = 1 (19) EDID Revision Number = 3 (20) VIDEO INPUT DEFINITION:
Digital Signal
Non - VESA DFP 1.x Compatible
(21) Maximum Horizontal Image Size = 380 mm
(22) Maximum Vertical Image Size = 300 mm (23) Display Gamma = 2.20 (24) Power Management and Supported Feature(s):
Active Off/Very Low Power, Standard Default Color Space,
Preferred Timing Mode
Display Type = R/G/B Color
(25-34) CHROMA INFO:
Red X - 0.634 Green X - 0.287 Blue X - 0.138 White X - 0.313
Red Y - 0.354 Green Y - 0.621 Blue Y - 0.077 White Y - 0.329
(35) ESTABLISHED TIMING I:
720 X 400 @ 70Hz (IBM,VGA)
640 X 480 @ 60Hz (IBM,VGA)
640 X 480 @ 67Hz (Apple,Mac II)
640 X 480 @ 72Hz (VESA)
640 X 480 @ 75Hz (VESA)
800 X 600 @ 56Hz (VESA)
800 X 600 @ 60Hz (VESA)
ViewSonic Corporation Confidential
22
-
Do Not Copy VX924
Page 26
(36) ESTABLISHED TIMING II:
800 X 600 @ 72Hz (VESA)
800 X 600 @ 75Hz (VESA)
832 X 624 @ 75Hz (Apple,Mac II)
1024 X 768 @ 60Hz (VESA)
1024 X 768 @ 70Hz (VESA)
1024 X 768 @ 75Hz (VESA)
1280 X 1024 @ 75Hz (VESA)
(37) Manufacturer's Reserved Timing:
1152 X 870 @ 75Hz (Apple,Mac II)
(38-53) Standard Timing Identification:
1280 X 1024 @60Hz
1152 X 864 @75Hz
1024 X 768 @85Hz
800 X 600 @85Hz
640 X 480 @85Hz
640 X 400 @70Hz
Not Used
Not Used ______________________________________________________________________
(54-71) Detailed Timing / Descriptor Block 1:
______________________________________________________________________
Horizontal Image Size: 376 mm Vertical Image Size: 301 mm
Refreshed Mode: Non-Interlaced Normal Display - No Stereo
Horizontal:
Vertical:
Digital Separate, Horizontal Polarity (+) Vertical Polarity (+) ______________________________________________________________________
(72-89) Detailed Timing / Descriptor Block 2:
______________________________________________________________________
(90-107) Detailed Timing / Descriptor Block 3:
______________________________________________________________________
(108-125) Detailed Timing / Descriptor Block 4:
Monitor Name:
(126) No Extension EDID Block(s) (127) CheckSum OK
1280x1024 Pixel Clock: 108.00 MHz
Active Time: 1280 pixels Blanking Time: 408 pixels
Sync Offset: 48 pixels Sync Pulse Width: 112 pixels
Border: 0 pixels Frequency: 63.98 KHz
Active Time: 1024 lines Blanking Time: 42 lines
Sync Offset: 1 lines Sync Pulse Width: 3 lines
Border: 0 lines Frequency: 60.02 Hz
Monitor Serial Number:
PS3050100001
Monitor Range Limits:
Min Vertical Freq - 50 Hz
Max Vertical Freq - 85 Hz
Min Horiz. Freq - 30 KHz
Max Horiz. Freq - 82 KHz
Pixel Clock - 140 MHz
Secondary GTF - Not Supported
VX924
ViewSonic Corporation Confidential
23
-
Do Not Copy VX924
Page 27
6. THEORY OF OPERATION
This section describes the function of the LCD monitor per functional block. This monitor includes MB board, power board and button board.
6.1 MB BOARD The MB board is a two-layer, single-grounded design with ground and internal planes provided. DC power from
the power board enters the board through a 6P connector. The other connector on the board is for the button board.
The VGA cable is a signal cable that carries the video, sync and DDC signals from the PC VGA adapter. This
system board consists of 4 functional areas: flat panel controller, MCU with flash ROM, and power regulators.
6.1.1 Flat panel controller: RTD2523(U7)
The heart of the system board is the Realtek RTD2523. The RTD2523 is a graphics processing IC designed for LCD monitors. It provides all key IC functions required for LCD displays. On-chip functions include a high-speed triple-ADC, PLL, high scaling engine and OSD controller.
a) Clock Generation:
Crystal Input Clock (TCLK and XTAL). This is the input pair to an internal crystal oscillator and
corresponding logic. A 24.576 MHz crystal is recommended.
b) Analog to Digital Converter:
The RTD2523 chip has three ADCs (analog-to-digital converters), one for each color (red, green and blue). The analog RGB signals are connected to RTD2523 as described below.
Pin Name Pin Number Red + 37 Red - 38 Green + 34 Green - 35 Blue + 30
Blue - 31
c) OSD: The RTD2523 has a fully programmable, high-quality OSD controller. The on-chip static
RAM (4096 words by 24 bits) stores the cell map and the cell definitions.
ViewSonic Corporation Confidential
24
-
Do Not Copy VX924
Page 28
d) MTV312 Micro Controller: The MTV312 micro controller (MCU) serves as the system micro controller.
It programs the RTD2523 and manages other devices in the system such as the keypad, the backlight, the LED, the audio system and the non-volatile RAM using general purpose input/output (GPIO) pins.
Pin number Pin Name Pin Usage
1 P5.2 Key / Power on, off 13 P3.4 NV_RAM (U4) SDA 14 P3.5 NV_RAM (U4) SCL 41 P5.4 Key_down 40 P5.5 Key_right 42 P5.3 Key_up 34 P5.6 Key_left 9 P6.3 Key_mute 2 P5.1 Key_select 27 P6.0 LED_red 26 P6.1 LED_green 16 P6.2 LCD panel power1 on / off control 17 P1.0 Backlight on / off control
e) Panel Power Sequencing (PANEL_PW12,3) (Pin 16, 18): The MTV312 has two dedicated outputs
VDDCTRL1 and 2 ( Pin32 and Pin3) to control LCD power sequencing once data and control signals
are stable.
f) Panel interface (Pin73~94): The RTD2523 driver interface is highly programmable. It supports dual bus /
dual port for SXGA d rive rs.
6.1.2 Power Regulator AIC1563 (U2), AIC1117CY (U1,U3): The AIC1563 is a monolithic control IC containing the primary functions required for DC to DC converters. The device consists of an internal temperature
compensated reference, a comparator, and a controlled duty cycle oscillator with an active current sense circuit. The desired output voltage is determined by the equation, Volt = 1.25 (1 + R11 / R12). In this case, the output voltage is 5 Volts. The AIC1563 is a low dropout positive adjustable regulator with minimum of 1A output current capability, so it is well suited to serve as a 3.3 V or
2.5 V regulator.
6.1.3 Power Regulator AIC1117CY (U1,U3): The AIC1117CY is a monolithic control IC containing the primary functions required for DC to DC converters. The device consists of an internal temperature compensated reference, a comparator, and a controlled duty cycle oscillator with an active current sense circuit. The desired output voltage is determined by the equation, Volt = 1.25 (1 + R17 / R15). In this case, the output voltage is 2.5 Volts for panel power.
ViewSonic Corporation Confidential
25
-
Do Not Copy VX924
Page 29
6.2 Power (Inverter) Board This is a specific power (inverter) board for VX912 monitor with output of 40W / 12V / 3.5A. It provides
12 VDC to drive the four cold cathode fluorescence tubes in the backlight.
6.2.1 The inverter's electrical specification is described below.
Input
Output
6.2.2 Power This is a general purpose AC / DC adapter which converts 90~240 Vac to a stabilized DC voltage: 12
Volts, with a rated output current of 4.16A. The electrical specification is described below.
Rated Input Voltage 12Vdc Input Voltage Range 11.4 ~ 12.6 Vdc Input Current <2A
On / Off control Voltage 2~3.3 for on, 0~1 for off Rated Output Strike-on Voltage 1500Vrms Rated Output Voltage 710Vrms at 7mA Rate Output Frequency 40~50KHz Rated Output Current 7~8 mA
Rated Input Voltage 90~240 Vac, 50 / 60Hz Operation Input Voltage 90~260 Vac, 47 ~ 63Hz Input Current <1.5A Inrush Current <100A@120Vac Standby Input Voltage 12Vdc Output Voltage Regulation +/-5% Output Ripple & Noise 120mVp-p Rate Output Current <3.5A Turn-on delay <3secs
ViewSonic Corporation Confidential
26
-
Do Not Copy VX924
Page 30
5. Adjustment Procedure
OSD Function Menu
A. When in Analog Input Mode
1. Main Menu
Press the [1] (Menu) button to enter the Main Menu: Press the [] button to highlight the previous item or the [▼] button to highlight the next item. Press the [1] (Menu) button to exit the Main Menu.
(1) Auto Image Adjust Page:
Press the [2] button to execute the auto image adjust function.
Press the [1] button to exit the page.
(2) Contrast/Brightness Page:
Press the [2] button to enter the contrast adjustment page.
Press the [1] button to exit the page.
1) Contrast Item
Press the [] button to increase the contrast. Press the [] button to decrease the contrast. Press the [2] button to enter the brightness adjustment page. Press the [1] button to exit the page.
2) Brightness Item
Press the [] button to increase the brightness. Press the [] button to decrease the brightness. Press the [2] button to enter the contrast adjustment page.
Press the [1] button to exit the page.
(3) Input Select Page:
Press the [2] button to switch to digital input mode.
(4) Color Adjust Page:
Press the [2] button to enter the color adjustment page. Press the [1] button to exit the page. Press the [] button to highlight the previous item or the [] button to
highlight the next item.
1) sRGB Item
2) 9300K Item
3) 6500K Item
4) 5400K Item
Press the [2] button to select the currently highlighted item.
Press the [1] button to exit the currently highlighted item.
5) User Color Item Press the [2] button to enter the user color page. Press the [1] button to exit the page.
Red, Green, Blue Options:
Press the [2] button to cycle among the colors. Press the [1] button to exit the page. Press the [] button to increase the selected color level.
Press the [] button to decrease the selected color level.
ViewSonic Corporation Confidential
27
-
Do Not Copy VX924
Page 31
(5) Information Page:
Press the [2] button to enter the information page. Press the [1] button to exit the information page.
(6) Manual Image Adjust Page:
Press the [2] button to enter the manual image adjustment page. Press the [1] button to exit the page. Press the [] button to highlight the previous item or the [] button to
highlight the next item.
1) H./V. Position Item
Press the [2] button to enter the horizontal/vertical postion adjustment page. Press the [1] button to exit the page.
a) Horizontal Position:
Press the [2] button to enter the vertical position adjustment page.
Press the [1] button to exit the page.
Press the [] button to shift the image to the right.
Press the [] button to shift the image to the left.
b) Vertical Position:
Press the [2] button to return to the horizontal position adjustment page.
Press the [1] button to exit the page.
Press the [] button to shift the image upward.
Press the [] button to shift the image downward.
2) Horizontal Size Item
Press the [2] button to enter the horizontal size adjustment page. Press the [1] button to exit the page. Press the [] button to make the image wider. Press the [] button to make the image narrower.
3) Fine tune Item
Press the [2] button to enter the fine tuning page. Press the [1] button to exit the page. Press “[]” Button to adjust character position in one direction. Press “[]“Button to adjust character position in the other direction.
4) Sharpness Item
Press the [2] button to enter the sharpness adjustment page. Press the [1] button to exit the page. Press “[]” Button to increase image sharpness. Press “[]“ Button to decrease image sharpness.
(7) Setup Menu Page:
Press the [2] button to enter the setup menu page. Press the [1] button to exit the page. Press the [] button to highlight the previous item or the [] button to
highlight the next item.
1) Language Select Item
Press the [2] button to enter the language selection page.
ViewSonic Corporation Confidential
28
-
Do Not Copy VX924
Page 32
Press the [1] button to exit the page. Press the [] button to highlight the previous item or the [] button to highlight the next item.
English, French… Option
Press the [2] button to select the language. Press the [1] button to exit the page.
2) Resolution Notice Item
Press the [2] button to enter the resolution notice page.
Press the [1] button to exit the page.
Enable, Disable Option
Press the [2] button to select the highlighted option. Press the [1] button to exit the page.
Press the [▲] button to highlight the previous option or the [] button to highlight the next option.
3) OSD Position Item
Press the [2] button to enter the OSD position adjustment page.
Press the [1] button to exit the page.
a) Horizontal Position Option
Press the [2] button to enter the vertical position adjustment page.
Press the [1] button to exit the page.
Press the [] button to shift the menu to the right.
Press the [] button to shift the menu to the left.
b) Vertical Position Option:
Press the [2] button to enter the horizontal position adjustment page.
Press the [1] button to exit the page.
Press the [] button to shift the menu upward.
Press the [] button to shift the menu downward.
4) OSD Time Out Item
Press the [2] button to enter the OSD time out adjustment page.
Press the [1] button to exit the page.
Press the [▲] button to increase the OSD time out.
Press the [] button to decrease the OSD time out.
5) OSD Background Item
Press the [2] button to enter the OSD background selection page.
Press the [1] button to exit the page.
Enable, Disable Option
Press the [▲] button to highlight the previous option or the [] button to highlight the next option.
Press the [2] button to select the highlighted option.
Press the [1] button to exit the page.
(8) Memory Recall Page
Press the [2] button to execute the memory recall function. Press the [1] button to exit the page.
ViewSonic Corporation Confidential
29
-
Do Not Copy VX924
Page 33
2. Other Menu:
This “shortcut” menu is directly accessible without bringing up the OSD.
(1) Contrast Dialog
Press the [] or [] button to enter the Contrast Dialog.
Press the [1] button to exit the Contrast Dialog.
Press the [2] button to enter the Brightness Dialog. Press the [] button to increase the contrast.
Press the [] button to decrease the contrast.
(2) Brightness Dialog
Press the [] or [] button to enter the Brightness Dialog.
Press the [1] button to exit the Brightness Dialog.
Press the [2] button to enter the Contrast Dialog. Press the [] button to increase the brightness.
Press the [▼] button to decrease the brightness.
(3) Analog/Digital Dialog
Press the [2] button to toggle between analog and digital modes.
B. When in Digital Input Mode
1. Main Menu
Press the [1] (Menu) button to enter the Main Menu: Press the [] button to highlight the previous item or the [▼] button to highlight the next item. Press the [1] (Menu) button to exit the Main Menu.
(1) Auto Image Adjust Page:
Press the [2] button to execute the auto image adjust function. Press the [1] button to exit the page.
(2) Contrast/Brightness Page:
Press the [2] button to enter the contrast adjustment page. Press the [1] button to exit the page.
1) Contrast Item
Press the [] button to increase the contrast. Press the [] button to decrease the contrast. Press the [2] button to enter the brightness adjustment page. Press the [1] button to exit the page.
2) Brightness Item
Press the [] button to increase the brightness. Press the [] button to decrease the brightness. Press the [2] button to enter the contrast adjustment page.
Press the [1] button to exit the page.
(3) Input Select Page:
Press the [2] button to switch to analog input mode.
(4) Color Adjust Page:
Press the [2] button to enter the color adjustment page.
ViewSonic Corporation Confidential
30
-
Do Not Copy VX924
Page 34
Press the [1] button to exit the page.
Press the [] button to highlight the previous item or the [] button to
highlight the next item.
1) sRGB Item
2) 9300K Item
3) 6500K Item
4) 5400K Item
Press the [2] button to select the currently highlighted item.
Press the [1] button to exit the currently highlighted item.
5) User Color Item Press the [2] button to enter the user color page. Press the [1] button to exit the page.
Red, Green, Blue Options:
Press the [2] button to cycle among the colors. Press the [1] button to exit the page. Press the [] button to increase the selected color level.
Press the [] button to decrease the selected color level.
(5) Information Page:
Press the [2] button to enter the information page. Press the [1] button to exit the information page.
(6) Manual Image Adjust Page:
Press the [2] button to enter the manual image adjustment page. Press the [1] button to exit the page. Press the [] button to highlight the previous item or the [] button to
highlight the next item.
1) Sharpness Item
Press the [2] button to enter the sharpness adjustment page. Press the [1] button to exit the page. Press “[]” Button to increase image sharpness. Press “[]“ Button to decrease image sharpness.
(7) Setup Menu Page:
Press the [2] button to enter the setup menu page. Press the [1] button to exit the page. Press the [] button to highlight the previous item or the [] button to
highlight the next item.
1) Language Select Item
Press the [2] button to enter the language selection page.
Press the [1] button to exit the page. Press the [] button to highlight the previous item or the [] button to highlight the next item.
English, French… Option
Press the [2] button to select the language. Press the [1] button to exit the page.
2) Resolution Notice Item
Press the [2] button to enter the resolution notice page.
ViewSonic Corporation Confidential
31
-
Do Not Copy VX924
Page 35
Press the [1] button to exit the page.
Enable, Disable Option
Press the [2] button to select the highlighted option. Press the [1] button to exit the page.
Press the [▲] button to highlight the previous option or the [] button to highlight the next option.
3) OSD Position Item
Press the [2] button to enter the OSD position adjustment page.
Press the [1] button to exit the page.
a) Horizontal Position Option
Press the [2] button to enter the vertical position adjustment page.
Press the [1] button to exit the page.
Press the [] button to shift the menu to the right.
Press the [] button to shift the menu to the left.
b) Vertical Position Option:
Press the [2] button to enter the horizontal position adjustment page.
Press the [1] button to exit the page.
Press the [] button to shift the menu upward.
Press the [] button to shift the menu downward.
4) OSD Time Out Item
Press the [2] button to enter the OSD time out adjustment page.
Press the [1] button to exit the page.
Press the [▲] button to increase the OSD time out.
Press the [] button to decrease the OSD time out.
5) OSD Background Item
Press the [2] button to enter the OSD background selection page.
Press the [1] button to exit the page.
Enable, Disable Option
Press the [▲] button to highlight the previous option or the [] button to highlight the next option.
Press the [2] button to select the highlighted option.
Press the [1] button to exit the page.
(8) Memory Recall Page
Press the [2] button to execute the memory recall function. Press the [1] button to exit the page.
2. Other Menu:
This “shortcut” menu is directly accessible without bringing up the OSD.
(1) Contrast Dialog
Press the [] or [] button to enter the Contrast Dialog.
Press the [1] button to exit the Contrast Dialog.
Press the [2] button to enter the Brightness Dialog. Press the [] button to increase the contrast.
Press the [] button to decrease the contrast.
ViewSonic Corporation Confidential
32
-
Do Not Copy VX924
Page 36
(2) Brightness Dialog
Press the [] or [] button to enter the Brightness Dialog.
Press the [1] button to exit the Brightness Dialog.
Press the [2] button to enter the Contrast Dialog. Press the [] button to increase the brightness.
Press the [▼] button to decrease the brightness.
(3) Analog/Digital Dialog
Press the [2] button to toggle between analog and digital modes.
C. Other Information
When the “No Signal” or “Out of Range” messages appear:
If no input signal is detected, the “No Signal” message will appear in the center of the screen. If the V-Sync signal rate is greater than than 85Hz or its resolution is greater than SXGA, the “Out of Range” message will appear in the center of the screen.
Activating Factory Mode and Burn Mode:
While the device is in standby, press the [2] button, then press the power button to enter Factory Mode. While Factory Mode is active, an additional menu page titled “Factory Menu” will be accessible. Press the [2] button to enter the Factory Menu page, then press the [2] button to enter Burn Mode.
When Installing a New Main Board
1. Enter Factory Mode.
2. Use a PC or chrom to send a 32-tone gray scale signal to the monitor.
3. Select “Auto Color”
ViewSonic Corporation Confidential
33
-
Do Not Copy VX924
Page 37
1. Function test
(1) Test equipment
Color video signal and pattern generator (or PC with SXGV resolution)
(2) Test condition
Before function testing and alignment, the unit must warm up for at least 30 minutes under the
following conditions:
1. Room temperature;
2. With full-white screen, RGB, black pattern;
3. With cycled display modes.
2. Test display modes
Item Timing Analog Digital
1 640 x 350 @ 70Hz, 31.5kHz Yes Yes 2 640 x 400 @ 60Hz, 31.5kHz Yes Yes 3 640 x 400 @ 70Hz, 31.5kHz Yes Yes 4 640 x 480 @ 50Hz, 24.7kHz No No 5 640 x 480 @ 60Hz, 31.5kHz Yes Yes 6 640 x 480 @ 67Hz, 35.0kHz Yes Yes 7 640 x 480 @ 72Hz, 37.9kHz Yes Yes 8 640 x 480 @ 75Hz, 37.5kHz Yes Yes
9 640 x 480 @ 85Hz, 43.27kHz Yes Yes 10 720 x 400 @ 70Hz, 31.5kHz Yes Yes 11 800 x 600 @ 56Hz, 35.1kHz Yes Yes 12 800 x 600 @ 60Hz, 37.9kHz Yes Yes 13 800 x 600 @ 75Hz, 46.9kHz Yes Yes 14 800 x 600 @ 72Hz, 48.1kHz Yes Yes 15 800 x 600 @ 85Hz, 53.7kHz Yes Yes 16 832 x 624 @ 75Hz, 49.7kHz Yes Yes 17 1024 x 768 @ 60Hz, 48.4kHz Yes Yes 18 1024 x 768 @ 70Hz, 56.5kHz Yes Yes 19 1024 x 768 @ 72Hz, 58.1kHz Yes Yes 20 1024 x 768 @ 75Hz, 60.0kHz Yes Yes 21 1024 x 768 @ 85Hz, 68.67kHz Yes Yes 22 1152 x 864 @ 75Hz, 67.5kHz Yes Yes 23 1152 x 870 @ 75Hz, 68.7kHz Yes Yes 24 1280 x 1024 @ 60Hz, 63.4kHz Yes Yes 25 1280 x 1024 @ 75Hz, 79.97kHz Yes Yes 26 1280x 720 @ 60Hz, 45kHz (HDTV) Yes Yes
ViewSonic Corporation Confidential
34
-
Do Not Copy VX924
Page 38
3. Test pattern
Item
1 Frequency & performance Cross-hatch pattern 2 Monitor saturation 16-gray scale pattern
3 RGB color performance RGB color Check the color temperature of
4 Sub-pixel defect RGB color Check for sub-pixel defects Pattern 3,
5 Full white Full white Check the brightness and contrast ratio,
6 Full black Full black Pattern 7
7. 5-cycle pattern 5-cycle pattern Check the BU Pattern 8
8. 1-dot pattern 1-dot pattern Check the flicker Pattern 9
Test condition Pattern Specification Remark
No noise is allowed, all colors must be clear
3 to 4 levels must be saturated when brightness and contrast are set to 100%
RGB signal color
and check for bright pixel defects
Pattern 1 Pattern 2
Pattern 3, 4, 5
4 , 5 Pattern 6
Pattern 1 Pattern 2
Pattern 3 Pattern 4
ViewSonic Corporation Confidential
35
-
Do Not Copy VX924
Page 39
Pattern 5 Pattern 6
Pattern 7 Pattern 8
Pattern 9
ViewSonic Corporation Confidential
36
-
Do Not Copy VX924
Page 40
6. Firmware update procedure :
When examining a monitor, please check whether the firmware version is the latest. If not,
please follow the procedure below to upgrade to the latest version.
1. Equipment needed :
- VX924
- PC ( Personal computer )
- LPT cable
- Fixture (LM5ISP)
- Firmware upgrade program
ViewSonic Corporation Confidential
37
-
Do Not Copy VX924
Page 41
2. Connection :
To PC
Appendix A : How to install the software for ISP:
1. To set up ISP environment: Hardware:
Software:
PC or notebook, parallel
(printer) cable, ISP tooling.
If OS is Win2000 or WinXP, please install "PORT95NT.exe".
In order to ensure that the system can execute the ISP program, please adjust the BIOS settings
in the PC or notebook as shown in Fig 0.0.
To Monitor
ViewSonic Corporation Confidential
Fig 0.0
38
-
Do Not Copy VX924
Page 42
2. Double-click the "PORT95NT.exe" icon in Windows and install the program; see Fig 0.1.
Fig 0.1
3. Continue through the installation process by pressing "Next" four times; see Fig. 0.2.
Fig. 0.2
ViewSonic Corporation Confidential
39
-
Do Not Copy VX924
Page 43
4. Choose "Typical" then press "Next;" see Fig. 0.3.
Fig. 0.3
5. Continue through the installation process by pressing "Next" four times; see Fig. 0.4.
Fig. 0.4
ViewSonic Corporation Confidential
40
-
Do Not Copy VX924
Page 44
6. When the installation is complete, restart the PC or notebook; see Fig 0.5.
Fig. 0.5
Install ISP
1. The user may download the ISP driver and PORT95NT installation package from the Myson Century website
(www.myson.com.)
2. The files extracted from the ZIP file are listed in Fig 1.0. Double-click setup.exe to install.
Fig 1.0
ViewSonic Corporation Confidential
41
-
Do Not Copy VX924
Page 45
3. Press the "Next" button to continue; see Fig 1.1.
Fig 1.1
4. Press the "Change" button to change the install path if desired, and then press the "Next" button to continue; see Fig 1.2.
Fig 1.2
ViewSonic Corporation Confidential
42
-
Do Not Copy VX924
Page 46
5. Press the "Install" button to continue; see Fig 1.3.
Fig. 1.3
6. When installation has finished, press the "Finish" button; see Fig 1.4.
Fig. 1.4
ViewSonic Corporation Confidential
43
-
Do Not Copy VX924
Page 47
Appendix B: How to use software to upgrade the BIOS:
1. After installation, shortcuts may be found in the settings path or the program menu (default setting); see Fig 2.1.
Fig. 2.1
2. The security file is a key to use ISP functions; press the "OK" button. See Fig 2.2.
3. The warning shown in Fig. 2.3 is used to remind the user that a CPU rate that differs from IIC protocol
may cause the ISP functions to fail; press the "OK" button.
Fig. 2.2
Fig. 2.3
ViewSonic Corporation Confidential
44
-
Do Not Copy VX924
Page 48
4. As shown in Fig. 2.4, press the "Create Security File" button to key in a security code, and use the slider bar to adjust the speed of the IIC bus.
Speed of IIC bus
Security code
Fig. 2.4
ViewSonic Corporation Confidential
45
-
Do Not Copy VX924
Page 49
5. Fig 2.5 shows the settings for the ISP software's security code. It requires two command numbers, and the commands must be keyed in sequentially: 7C, 4C, 77. The command numbers and commands
must be set by the user while coding. For more details, please refer to section 6 boot code of ISP.
Fig. 2.5
ViewSonic Corporation Confidential
46
-
Do Not Copy VX924
Page 50
Appendix C: Using ISP to program MCU
1. As shown in Fig. 3.1, select the MTV type first, load the binary or intel hex file to be programmed into the MCU, click "OK," then press the "RUN" button.
Step 2
Step 1
Step 4
Step 3
Fig. 3.1
ViewSonic Corporation Confidential
47
-
Do Not Copy VX924
Page 51
2. If the user changes the MTV type, the file must be loaded again, as the previously loaded file will be cleared.
3. CRC (cyclic redundancy check): the host can check the result in the CRC register instead of reading every byte in flash.
The Check MCU CRC OK message indicates that the host has verified the program's CRC; see Fig.3.2.
Fig. 3.2
ViewSonic Corporation Confidential
48
-
Do Not Copy VX924
Page 52
6. Troubleshooting Flow Chart
1. Display color abnormal:
ViewSonic Corporation Confidential
49
-
Do Not Copy VX924
Page 53
2. Monitor cannot power on
Can not power on monitor
Change adaptor
Repair open / short
Change X1 / X2
Change failed part
NO
NO
NO
NO
Check adaptor
OK
Check K/B Open / short?
OK
Check crystal X1 / X2?
OK
Check CN 6, R79
Pin 40 of U6?
OK
Fix power supply circuit
NO
Check power supply
(12V, 5V, 2.5V & 3.3V)
OK
Change M/B
ViewSonic Corporation Confidential
50
-
Do Not Copy VX924
Page 54
3. Monitor white screen
ViewSonic Corporation Confidential
51
-
Do Not Copy VX924
Page 55
4. Monitor black screen
ViewSonic Corporation Confidential
52
-
Do Not Copy VX924
Page 56
5. Analog input: always shows NO SIGNAL:
ViewSonic Corporation Confidential
53
-
Do Not Copy VX924
Page 57
6. Digital input: always shows NO SIGNAL
ViewSonic Corporation Confidential
54
-
Do Not Copy VX924
Page 58
7. Recommended Spare Parts List
RECOMMENDED SPARE PARTS LIST (VX924-1)
ViewSonic Model Number: VS10162-3W Rev: 1a
Item ECR/ECN ViewSonic P/N Ref. P/N Location Q'ty
PC Board Assembly:
1 main board B-00002519 29L9IMB00E5 main board 1 2 Over driver board B-00002520 22L9V0B0005 Over driver board 3 Power board B-PS-0204-0076 AS02B012D24 power board 1
Cabinets:
4 5 Front bezel assy C-FP-0301-1033 6 Stand cover rear C-00001778
Cables:
7 Cable for MB-B/B (8P/10P. Rev.1A) M-MS-0808-9398 DDL7VDTH009 M/B-B/B cable 1 8 Cable for MB-LCD (30P. Rev.1A) CB-00002525 9 Cable for MB-over driver CB-00002522 DD0L9V0B000 MB-over driver cable
10 VGA cable M-MS-0808-9399 DDL7VDPC005 VGA cable 1
Documentation:
11
Electronic
12
Hardware:
13 Screw M4*6-I (BNI)(NYLOK) M-SCW-0824-6859 14 Screw M3.0*4.0-I(NI) M-SCW-0824-6802
Miscellaneous:
15 LCD film L9V M-MS-0808-9682 JXL9V001010 LCD panel film 1 16 4ms sticker M-00002524
Packing Material:
17 Carton P-00002521 HFL9V007011 carton 1 18 End cap (L) P-FM-0602-0896 19 End cap (R) P-FM-0602-0897 20 EPE bags M-MS-0808-9817 HAL9V002014 EPE bags 1
Description
Back cover assy
User manual + CD wizard DC-00002523 HGL9V0011019 user's manual 1 19" AUO TFT LCD panel E-00001775 AAM190EN129 LCD panel 1
C-BC-0302-0626
33L9VBCVS05 32L9VFBVS07
EBL9V002015
DD0L9VLC015
MM40060IL69 MM30040IBJ9
HCL9V007018
HBL9V001019 HBL9V002015
back cover 1
front bezel ass'y 1
stand cover 1
MB-LCD cable 1
Screw 4 Screw 14
4ms sticker on carton 1
cushion 1 cushion 1
ViewSonic Corporation Confidential
55
-
Do Not Copy VX924
Page 59
BOM LIST (VX924-1)
ViewSonic Model Number: VS10162-3W Rev: 1a
Item ViewSonic P/N Ref. P/N Description Location Q'ty
1 #N/A 1L9VDZAVS92 L9V LCD MONITOR(L9VDA-5,AU VX924)US 2 B-00002519 29L9IMB00E5 L9I M/B ASSY(FOR L9VDA-5 REALTEK,2523)AU 1 3 #N/A 39L9IDP0056 L9I M/B DIP ASSY(L9VDA-5 REALTEK)2523 1 4 #N/A 41L9ISS0053 L9I M/B S/S ASSY(L9VDA-5 REALTEK)2523 1
5 #N/A CC62204MD23 CAP ELEC 22U 25V(+-20%,105C,5*11,2000HR)
6 #N/A CC622L4MD06 CAP ELEC DIP 22U 25V(+-20%,105C,5*11)LXN 7 #N/A CC71004MD68 CAP ELEC 100U 25V +-20%,105C,6*11,LESR C70 1
8 #N/A CC710L4MD08 CAP ELEC 100U 25V(+-20%,105C,6*11)LXN C70 1
9 #N/A CC73303MD51 CAP ELEC 330U 16V(+-20%,105C,8*11,2000HR C6,EC4 2 10 E-L-0407-1563 DC04725K002 CHOKE COIL 47UH(2.5A,+-10%,T07473) L2 1 11 #N/A BG624576031 CRYSTAL DIP 24.576MHZ(30PPM,20PF,49/US) Y1 1 12 #N/A BG611059319 CRYSTAL DIP 11.0592MHZ(+-30PPM,49/US) Y2 1 13 #N/A DFHD06MR247 CONN DIP HEADER 6P 2R MR(P2.5,H6.0) CN1 1 14 #N/A DFDS15FR050 CONN D-SUB 15P 3R FR,P1.15,H12.55,NO SRW CN2 1 15 #N/A DFDI30FR049 CONN DVI-I DIP30P 3R FR(P1.905,H10.04) CN4 1 16 M-MS-0808-9809 DFHD30MR259 CONN DIP HEADER 30P 2R MR(P2.0,H4.0) CN5 1 17 M-MS-0808-9810 DFHD10MR316 CONN DIP HEADER 10P 1R MR(P2.0,H4.1) CN6 1 18 #N/A AZL9VD0A206 L9VDA-5 SW BIOS IMAGE REALTEK(AU)2523 1 19 B-00002520 22L9V0B0005 L9V OVER DRIVER/B ASSY 1 20 #N/A DA0L9V0B2B8 PCB(OD/B) L9V ODB(2L,85*90MM REVB) 1 21 #N/A AJ036010F00 IC(208P)LCD OVERDRIVE VTIO3601(LQFP) U4 1 22 #N/A AKD24G-K501 IC SDRAM(50P) K4S161622H-TC60 TSOP U2,U5,U6,U7 4 23 #N/A AKE24FU0K13 IC FLASH SST25VF512A-33-4C-SAE SO8 GP U3 1 24 #N/A AL001084013 IC(3P) L1084D(TO-252) U1 1
25 #N/A CH41004Z931 CAP CHIP 0.1U,25V(+80-20%,Y5V,0603) GP
26 #N/A CH61001ZA31 CAP CHIP 10U 6.3V(+80%-20%,Y5V,0805)
27 #N/A CJ033084N16 RES ARRAY CHIP 33,1/16W(5%,8P4R)R-PIN
28 #N/A CS03303J909 RES CHIP 33 1/10W +-5%(0603) R21 1 29 #N/A CS11003F902 RESISTOR CHIP 100 1/10W+-1%(0603) 30 #N/A CS12003F905 RESISTOR CHIP 200 1/10W+-1%(0603) R1 1
31 #N/A CS13303F909 RESISTOR CHIP 330 1/10W +-1%(0603) R2 1 32 #N/A CS31003J908 RES CHIP 10K 1/10W +-5%(0603) R8 1 33 #N/A CS21003J906 RES CHIP 1K 1/10W +-5%(0603) R14 1 34 #N/A DFHD30MS026 CONN SMD HEADER 30P 2R MS(P2.0,H4.0) JP1,JP2 2 35 #N/A CX201209805 EMI FILTER CHIP FBM-11-201209-121A40 GP L1,L2,L3,L4,L5 5 36 B-CB-0206-0188 23L7VBB0034 L7VD BUTTON/B ASSY 1 37 #N/A DFHD08MR301 CONN DIP HEADER 8P 1R MR(P2.0,H4.1) CN1 1 38 #N/A BEYG0013DA3 LED(DIP) YELLOW/GREEN(L-3WYGW) LED1 1 39 #N/A DAL7VDTB1A3 PCB(BUTTON) L7VD TL(1L,180*15,REVA) 1 40 #N/A DHP0002B205 SWITCH PUCH BUTTON(PT-002-B2,50MA,12V) SW1,SW2,SW3,SW4,SW5 5 41 B-PS-0204-0076 AS02B012D24 ADD/INV,FSP035-1PI01,90~264V REV1A 1 42 #N/A 23L9VLAVS63 L9VDA-5 LCD MOUDLE ASSY(AU,VX924) 1 43 C-FP-0301-1033 32L9VFBVS07 L9V FRONT BEZEL ASSY 1 44 C-00000987 EAL9V001018 BEZEL L9V(EAL9V001,REV3A) 1 45 C-FP-0301-1047 EAL9V002014 MIDDLE BEZEL L9V(EAL9V002,REV3A) 1 46 M-MS-0808-9401 EBL7V028019 LENS L7VD(EBL7V028,REV3A) 1 47 PL-BT-0706-0165 EBL7V027012 CONTROL BUTTON L7VD(EBL7V027,REV3A) 1 48 M-MS-0808-9243 FEL7V003019 LOGO FRONT-VSC-38MM L7VC(FEL7V003,REV3A) 1 49 M-MS-0808-9402 FEL7V007014 BIRD LOGO L7VD(FEL7V007,REV3A) 1 50 C-BC-0302-0626 33L9VBCVS05 L9V BACK COVER ASSY 1 51 M-CV-0830-2592 EAL9V003011 LCD COVER L9V(EAL9V003,REV3A) 1 52 M-MS-0808-9253 FEL7V005011 LOGO PLATE ELLIPSE L7VC(FEL7V005,REV3A) 1 53 M-MS-0808-9411 FBL70008014 LOCK METAL L70B(FBL70008,REV3A) GP 1 54 M-CV-0830-2590 FBL9V001019 HINGE -L L9V(FBL9V001,REV3A) 1 55 M-BK-0805-0111 FBL9V002015 HNGE-BKT L9V(FBL9V002,REV3A) 1 56 M-CV-0830-2591 FBL9V003011 HINGE-R L9V(FBL9V003,REV3A) 1 57 M-SCW-0824-6895 MF40080IBJ1 SCREW F4.0*8-I(NI) 8 58 M-SCW-0824-6859 MM40060IL69 SCREW M4*6-I (BNI)(NYLOK)) 6 59 E-00001775 AAM190EN129 LCD(TFT) 19" M190EN04 REV:V5 1 60 M-BK-0805-0079 FAL7V014017 PCB BKT L7VD(FAL7V014,REV3A) 1 61 M-MS-0808-9405 FAL7V015013 PCB SHIELDING L7VD(FAL7V015,REV3A) 1 62 HW-00001807 FBL9V009010 LCD BKT L-R L9VD-1(FBL9V009,REV3A) 2 63 HW-00001802 FBL9V010018 LCD PANEL LOCK METAL L9VD1(FBL9V010,R3A) 2
C34,C46,C50,C53,C59,C84,EC1,EC2 ,EC3,EC5,EC6 C34,C46,C50,C53,C59,C84,EC1,EC2 ,EC3,EC5,EC6
C2,C4,C6,C7,C8,C9,C10,C11,C12,C1 3,C14,C15,C16,C17,C34,C35,C36,C3 7,C38,C39,C40,C41,C42,C43,C44,C4 5,C60,C61,C62,C63,C64,C65,C66,C6 7,C68,C69,C70,C71,C72,C73,C76,C7 7,C78,C79,C80,C81,C82,C83,C84,C8 5,C86,C87,C88,C89 C1,C3,C5,C18,C19,C21,C22,C23,C24 ,C32,C33,C58,C59,C74,C75 PR1,PR2,PR3,PR4,PR5,PR6,PR7,PR 8,PR9,PR10,PR11,PR12,PR13,PR14, PR15,PR16
R3,R4,R5,R6,R7,R9,R10,R11,R12,R1 3
11
11
54
15
16
10
ViewSonic Corporation Confidential
56
-
Do Not Copy VX924
Page 60
Item ViewSonic P/N Ref. P/N Description Location Q'ty
64 M-SCW-0824-0726 MF30080BBJ5 SCREW F3.0*8L,B,NI 2 65 M-SCW-0824-6802 MM30040IBJ9 SCREW M3.0*4.0-I(NI) GP 14 66 M-SCW-0824-6800 MM30060IBJ8 SCREW M3.0*6.0-I(NI) GP 11 67 M-SCW-0824-6799 MM35080BBW2 SCREW M3.5*8-B (NI,WASHER) 1 68 M-MS-0808-8986 MBLI1004018 IO NUT LI1(MBLI1004,REV3A) 4 69 M-MS-0808-9247 EBL70023013 WIRE MOUNTS L70L-E(EBL70023,REV3A) GP 1 70 #N/A EBL7V030013 PCB SPACER L7VD(EBL7V030,REV3A) 1 71 PL-00001804 GAL70002015 RUBBER-HOLDER L70L(GAL70002,REV3B) 2 72 PL-00001806 GAL5T001016 RUBBER-HOLDER L5TL-E(GAL5T001,REV3B) 4 73 PL-00001805 GAL70005014 RUBBER-BKT(T) L70L-T(GAL70005,REV3A) 2 74 #N/A MBL9V001019 IO NUT L9VDA-5(MBL9V001,REV3A)M3*15*6 2 75 #N/A GAL7E002013 LCD RUBBER L7E(GAL7E002,REV3B) 1 76 C-BS-0303-0553 24L9VSAVS02 L9V STAND ASSY 1 77 #N/A 34L9VSBVS08 L9V STAND BKT ASSY 1 78 C-BS-0303-0553 EAL9V004017 STAND BASE L9V(EAL9V004,REV3A) 1 79 M-MS-0808-9811 GAL5M002011 RUBBER FOOT L5M(GAL5M002,REV3B) 4 80 M-CV-0830-2589 EAL9V005013 STAND BKT COVER L9V(EAL9V005,REV3A) 1 81 M-SCW-0824-0813 MF30060BBJ6 SCREW F3.0*6-B(NI) 9 82 M-MS-0808-9812 EBL9V001019 STAND COVER F L9V(EBL9V001,REV3A) 1 83 M-MS-0808-9404 EBL7V029015 WIRE CLAMP L7VD(EBL7V029,REV3A) 2 84 M-SCW-0824-6894 MF30060BJ28 SCREW F3.0*6-B(BNI) 4 85 #N/A 25L9VCSVS50 L9VDA-5 CHASSIS ASSY(VX924) 1 86 CB-00002525 DD0L9VLC015 CABLE MB-LCD(30P,140MM)L9V-5 GP 1 87 M-MS-0808-9398 DDL7VDTH009 CABLE ASSY L7VD BUTTON-MB(8P/10P,REV1A) 1 88 C-00001778 EBL9V002015 STAND COVER R L9V(EBL9V002,REV3A) 1 89 M-CV-0830-2593 EBL9V003011 I/O COVER L9V(EBL9V003,REV3A) 1 90 M-SCW-0824-6859 MM40060IL69 SCREW M4*6-I (BNI)(NYLOK)) 4 91 M-SCW-0824-0870 MS40070B808 SCREW M4*7B (BMC)NYLOK 4 92 M-MS-0808-9815 GAL9V002014 RUBBER PLUG VESA L9V(GAL9V002,REV3A) 4 93 CB-00002522 DD0L9V0B000 CABLE MB-OVER DRIVER(30P,50MM)L9V-5 GP 1 94 #N/A 26L9VPKVSP1 L9VDA-5 PACKING ASSY(AU,VX924)US 1 95 M-MS-0808-9399 DDL7VDPC005 CABLE ASSY L7VD MB-VGA (15/15P,REV1A) 1 96 A-PC-0106-0224 DM333181G97 POWER CORD 3P 1.8M(USA)V04VS35001218000 1 97 M-MS-0808-9817 HAL9V002014 EPE BAG L9VD(HAL9V002,REV3A) 1 98 P-FM-0602-0896 HBL9V001019 END CAP-L L9V(HBL9V001,REV3A) 1 99 P-FM-0602-0897 HBL9V002015 END CAP-R L9V(HBL9V002,REV3A) 1
100 M-LB-0813-0747 HCL7V004013 CORE LABEL(HCL7V004,REV3A) 1 101 #N/A HCL9V006011 ID LABEL VX924 L9VDA-5(HCL9V006,REV3A) 1 102 M-LB-0813-0745 HCL7V002011 SERIAL LEBAL L7V(HCL7V002,REV3A) 1 103 M-LB-0813-1042 HCL7V019011 CARTON LABEL L7VC(HCL7V019,REV3B) 1 104 P-00002521 HFL9V007011 CARTON VX924 L9VDA-5(HFL9V007,REV3A) 1 105 #N/A HGL9V011019 CD+QSG VX924 L9VDA-5 USA(HGL9V011,REV3A) 1 106 #N/A JXLM5003011 HANDLE LM5S(JXLM5003,REV 3B) GP 1 107 M-MS-0808-9682 JXL9V001010 LCD FILM L9V(JXL9V001,REV3A) 1 108 M-LB-0813-1043 HCL70021011 HI-POT LABEL L70L(HCL70021,REV3A) 1 109 #N/A HFL9V002019 SPACE PLATE L9V(HFL9V002,REV3A) 0.05 110 M-00002524 HCL9V007018 4MS STICKER VX924 L9VD(HCL9V007,REV3A) 1
ViewSonic Corporation Confidential
57
-
Do Not Copy VX924
Page 61
8. Exploded Diagram and Spare Parts List
ViewSonic Corporation Confidential
58
-
Do Not Copy VX924
Page 62
EXPLODED PARTS LIST (VX924-1)
ViewSonic Model Number: VS10162-3W Rev: 1a
Item ViewSonic P/N Ref. P/N Description Q'ty
1 C-00000987 EAL9V001018 BEZEL L9V(EAL9V001,REV3A) 1 2 C-FP-0301-1047 EAL9V002014 MIDDLE BEZEL L9V(EAL9V002,REV3A) 1 3 PL-BT-0706-0165 EBL7V027012 CONTROL BUTTON L7VD(EBL7V027,REV3A) 1 4 M-MS-0808-9243 FEL7V003019 LOGO FRONT-VSC-38CM L7VC(FEL7V003,REV3A) 1 5 M-MS-0808-9401 EBL7V028019 LENS L7VD(EBL7V028,REV3A) 1 6 M-MS-0808-9402 FEL7V007014 BIRD LOGO L7VD(FEL7V007,REV3A) 1 7 B-CB-0206-0188 23L7VBB0034 L7VD BUTTON/B ASSY 1 8 HW-00001802 FBL9V010018 LCD PANEL LOCK METAL L9V 2
9 M-SCW-0824-0726 MF30080BBJ5 SCREW F3.0*8L,B,NI 2 10 E-00001775 AAM190EN129 LCD(TFT) 19" M190EN04 REV:V5 1 11 HW-00001807 FBL9V009010 LCD BKT L9V(FBL9V004,REV3A) 2 12 M-SCW-0824-6802 MM30040IBJ9 SCREW M3.0*4.0-I(NI) GP 4 13 M-BK-0805-0079 FAL7V014017 PCB BKT L7VD(FAL7V014,REV3A) 1 14 CB-00002522 DD0L9V0B000 CABLE MB-OVER DRIVER(30P,50MM) L9V-5 GP 1 15 B-PS-0204-0076 AS02B012D24 ADD/INV,FSP035-1PI01,90~264V REV1A 1 16 B-00002519 29L9IMB00E5 L9I M/B ASSY (FOR L9VDA-5 REALTEK2523)AU 1 17 M-MS-0808-9398 DDL7VDTH009 CABLE ASSY L7VD BUTTON-MB (8P-10P) 1 18 M-SCW-0824-6799 MM35080BBW2 SCREW M3.5*8-B (NI,WASHER) 1 19 M-SCW-0824-6800 MM30060IBJ8 SCREW M3.0*6.0-I(NI) 7
20 M-MS-0808-9405 FAL7V015013 PCB SHIELDING L7VD(FAL7V015,REV3A) 1 21 HW-00000989 MM30040IBJ8 SCREW M3.0*4.0-I(NI) 10 22 M-MS-0808-9811 GAL5M002011 RUBBER FOOT L5M(GAL5M002,REV3B) 4 23 M-SCW-0824-0813 MF30060BBJ6 SCREW F3.0*6-B(NI) 1 24 M-CV-0830-2589 EAL9V005013 STAND BKT COVER L9V(EAL9V005,REV3A) 1 25 M-MS-0808-9812 EBL9V001019 STAND COVER F L9V(EBL9V001,REV3A) 1 26 M-BK-0805-0110 FBL9V005014 STAND BKT L9V(FBL9V005,REV3A) 4 27 C-BS-0303-0553 EAL9V004017 STAND BASE L9V(EAL9V004,REV3A) 1 28 M-MS-0808-9813 FBL9V006011 STAND PLATE L9V(FBL9V006,REV3A) 1 29 M-SCW-0824-6859 MM40060IL69 SCREW M4*6-I (BNI)(NYLOK)) 4 30 M-SCW-0824-6894 MF30060BJ28 SCREW F3.0*6-B(BNI) 4 31 M-MS-0808-9404 EBL7V029015 WIRE CLAMP L7VD(EBL7V029,REV3A) 2 32 C-00001778 EBL9V002015 STAND COVER R L9V(EBL9V002,REV3A) 1 33 M-SCW-0824-6895 MF40080IBJ1 SCREW F4.0*8-I(NI) 8 34 M-BK-0805-0111 FBL9V002015 HNGE-BKT L9V(FBL9V002,REV3A) 1 35 M-CV-0830-2590 FBL9V001019 HINGE-L L9V(FBL9V001,REV3A) 1 36 M-CV-0830-2591 FBL9V003011 HINGE-R L9V(FBL9V003,REV3A) 1 37 M-MS-0808-9411 FBL70008014 LOCK METAL L70B(FBL70008,REV3A) 1 38 M-CV-0830-2592 EAL9V003011 LCD COVER L9V(EAL9V003,REV3A) 1 39 M-SCW-0824-6859 MM40060IL69 SCREW M4.0x6 (BNI)NYLOCK 6 40 M-CV-0830-2593 EBL9V003011 I/O COVER L9V(EBL9V003,REV3A) 1 41 M-MS-0808-9253 FEL7V005011 LOGO PLATE 1 42 M-SCW-0824-0870 MS40070B808 SCREW M4.0x7 (BMC)NYLOCK 4 43 M-MS-0808-9815 GAL9V002014 RUBBER PLUG VESA L9V 4 44 PL-00001804 GAL70002015 RUBBER HOLDER 2 45 PL-00001805 GAL70005014 RUBBER BKT 2 46 PL-00001806 GAL5T001016 RUBBER HOLDER 4 47 CB-00002525 DD0L9VLC015 CABLE MB-LCD(30P, 140MM) 1 48 N/A MBL9V001019 IO NUT L9VDA-5 2 49 B-00002520 22L9V0B0005 L9V OVER DRIVER/B ASS'Y 1
ViewSonic Corporation Confidential
59
-
Do Not Copy VX924
Page 63
Packing for shipping
PACKING PART LIST (VX924-1)
ViewSonic Model Number: VS10162-3W Rev: 1a
Item ViewSonic P/N Ref. P/N Location Q'ty
1 VX924 1L9VDZAVS41 VX924 unit 1 2 P-FM-0602-0896 HBL9V001019 END CAP(L) 1 3 P-FM-0602-0897 HBL9V002015 END CAP(R) 1 4 DC-00002523 HGL9V0011019 User manual & CD 1 5 A-PC-0106-0224 DM333181G97 Power cord 3P 1.8M 1 6 P-00002521 HFL9V007011 Carton 1 7 M-LB-0813-1042 HCL7V019011 Carton label 1 8 M-MS-0808-9817 HAL9V002014 EPE bag 1
ViewSonic Corporation Confidential
60
-
Do Not Copy VX924
Page 64
Packing procedure
1. Apply protective film to the display surface.
2. Put the monitor in EPE bag and seal the bag with tape.
3. Fit the cushions onto the monitor.
ViewSonic Corporation Confidential
61
-
Do Not Copy VX924
Page 65
Q
4. Put the monitor into the carton and put all the accessories into the carton.
Then close the carton.
SG
Power cord
Disassembling the monitor
1. Turn the monitor to face the back and remove the I/O cover.
2. Remove the stand back cover.
ViewSonic Corporation Confidential
62
-
Do Not Copy VX924
Page 66
3. Remove the four black hinge screws and separate the stand and head pieces.
4. Place the monitor face-down on a soft, flat, stable surface.
5. Separate the back cover and the front bezel.
ViewSonic Corporation Confidential
63
-
Do Not Copy VX924
Page 67
6. Remove the screws that fix the button board (B/B) and pull the cable out from the
connector on the main board (M/B).
7. Remove the B/B.
8. Remove the screws on the PCB shield; remove the PCB shield.
Screws
ViewSonic Corporation Confidential
64
-
Do Not Copy VX924
Page 68
9. Remove the MB-LCD connector and loosen the four screws on the PCB holder.
Screws
10. Separate the PCB holder from the panel.
ViewSonic Corporation Confidential
65
-
Do Not Copy VX924
Page 69
11. Loosen the four screws on the sides of the panel.
12. Remove the front bezel and panel.
ViewSonic Corporation Confidential
66
-
Do Not Copy VX924
Page 70
13. Remove the four hexagon screws beside the DVI & D-SUB connectors.
14. Remove the screws that fix the power board and main board.
ViewSonic Corporation Confidential
67
-
Do Not Copy VX924
Page 71
Do Not Copy VX924
-
68
Block Diagram
9.
ViewSonic Corporation Confidential
Page 72
Do Not Copy VX924
-
69
ViewSonic Corporation Confidential
Page 73
10. Schematic Diagrams
+3.3V
+2.5V
DVI
PC VGA
ANALOG RGB
+3.3V
EEPROM 24LC16
DDC
AC 90-264V
SCALAR RTD2523
MICRO-CONTROLLER MTV312
INVCTRL
BRIGHTNESS
AUDIO_VOLUME
POWER INVERTER AND AUDIO BOARD
+3.3V
+3.3V
AUDIO_MUTE
+12V
RSDS AND LVDS
+3.3V
+12V
POWER
LCDPWR_ON12V
LCDPWR_ON3.3V
AIC 1563
LCDVCC
+5.0V
AIC1739
LCD PANEL(17 19 RSDS AND LVDS)
+2.5V
ViewSonic Corporation Confidential - Do Not Copy VX924
70
AIC1739
+3.3V
Title
<Title>
BLOCK DIAGRAM
Size Document Number
<Doc>
C
Friday, October 15, 2004
Date:
Sheet
Rev
28
of
Page 74
DAN217K/NC
RED+IN
IN-H
D7
3
GND
IN-H
DDC_SCL
ADC_VCC
21
1 3
DDC_SDA IN-H
IN-V
DDC_SCL
RED-IN GREEN-IN BLUE-IN
GREEN+IN
IN-V
D10
Z5.6/NC
CN2
11
12
13
14
15
VGA/NC
11 13
D8
DAN217K/NC
1 3 5 7 9
3
1 3
1617
CN3
+
+
+
+
+
+
+
+
+
+
+
+
+
+
VGA INPUT
21
DDC_SDA
D11
Z5.6/NC
1 6 2 7 3 8 4 9 5 10
2 4 6 8 10 12 14
BLUE+IN
PAGE1 VGA INPUT
RED+IN GREEN+IN BLUE+IN GND IN-V DDC_SDA DSUB_5V
D9
DAN217K/NC
D12
1 3
21
3
DDC_SCL
Z5.6/NC
RED+IN RED-IN GREEN+IN GREEN-IN BLUE+IN BLUE-IN
DSUB_5V
PIN 10 VGA_CON
DEL D29 2004/6/17
D13
Z5.6/NC
1 3
DDC_SDA
DSUB_5V
DDC_SCL
RED+IN
RED-IN
GREEN+IN
GREEN-IN
BLUE+IN
BLUE-IN
L8 0/6
L9 0/6
L10 0/6
R24
75/6/F
R27
75/6/F
R32
75/6/F
IN-H
C17
NC
C20
NC
C24
NC
L31 0/6
IN-V
R34 100/6
R35
2K/6
R36 100/6
R37
2K/6
R23 100/6
R25 100/6
R26 100/6
R28 100/6
R29 100/6
R31 100/6
R33 100/6
C26
22P/6
VGAVS
C28
22P/6
C16 0.047u/6
C18 0.047u/6
C19 0.047u/6
C21 0.047u/6
C22 0.047u/6
C23 0.047u/6
C25 0.047u/6
VGAHS
RED+
RED-
GREEN+
GREEN-
SOGIN
R30 1M/6
BLUE+
BLUE-
D34
Z3.3V
1 3
D35
Z3.3V
1 3
AHS
Add D34,D35,L31 2004/6/17
AVS
C29 0.1U/6/NC
DEL L11,C32,U6,R51,R52 2004/6/17
Bus_Power
3DVCC
D17
BAT54C-GS08/NC
CN4
25
1
RX2-
2
RX2+
3
GND
4
RX4-
5
RX4+
6
SCL
7
SDA
8
VS
9
RX1-
10
RX1+
11
GND
12
RX3-
13
RX3+
14
5V
15
GND
16
HP
17
RX0-
18
RX0+
19
GND
20
RX5-
21
RX5+
22
GND
23
RXC+
24
RXC-
26
DDC2_SCL DDC2_SDA
R48 10K/6NC R49 100/6NC
D24 C31 1U/6NC
Z5.6/NC
1 3
Bus_Power
Hot_plug
C30
0.1U/6/NC
DVI-D/NC
ViewSonic Corporation Confidential - Do Not Copy VX924
D18
1 3
D20
1 3
D25
1 3
Z5.6/NC
Z5.6/NC
Z5.6/NC
D19
Z5.6/NC
1 3
D21
Z5.6/NC
1 3
D26
Z5.6/NC
1 3
D27
Z5.6/NC
1 3
71
Add R156~R162 damping RES 2004/4/16
D28
Z5.6/NC
1 3
R155 0 R156 0
R157 0 R158 0
R159 0 R160 0
R161 0 R162 0
R50
10K/6NC
TX2­TX2+
TX1­TX1+
TX0­TX0+
TXC+ TXC-
U5
1
NC
2
NC
3
NC
4 5
VSS SDA
Title
Size Document Number
Date:
8
VCC
7
VCLK
6
SCK
M24C02/NC
VGA AND DVI INPUT
Friday, October 15, 2004
R44 2K/6/NC
D22
Z5.6/NC
1 3
DISPLAY
R45 2K/6/NC
R46 100/6/NC
R47 100/6/NC
D23
Z5.6/NC
1 3
38
Sheet of
DDC2_SCL DDC2_SDA
Rev
B
Page 75
TMDS_AVCC
R57
NC
R58
4.7K/6
3AVCC1
3PVCC
3AVCC2 TMDS_AVCC
3AVCC2
C54
0.1u/6
L19 FEB_0805
C60
0.1u/6
R54
R55
L15 FEB_0805
22uF/16V
3PVCC
4.7K/6
4.7K/6/NC
L14 FEB_0805
C49
C53
ADC_VCC3AVCC1
3DVCC
C33 22pF/6
R53 NC
C48 22pF/6
0.1u/6
PLL_GND
+
+
0.1u/6
C59
C61
22uF/16V
ADC_GND
C43.C44.C45 IC
L12
FEB_0805
Y1
10uF/16V
0.1u/6
C50
C51
R56 1K/6
TX2+ TX2­TX1+ TX1­TX0+ TX0­TXC+ TXC-
Near to Chip
0.1u/6
0.1u/6 C56
C55
BLUE+ BLUE-
SOGIN GREEN+ GREEN-
RED+
RED-
0.1u/6
C63
C62
盡量靠近
XO
24.576MHz
XI
0.1u/6
C52
0.1u/6
C57
0.1u/6
C64 0.1u/6
AHS AVS
RX2P RX2N RX1P RX1N RX0P RX0N RXCP RXCN
0.1u/6
C58
RTD_SCLK
RTD_SDO/SDI
RTD_SCSB
C34
XO XI
B+ B­SOG G+ G­R+ R-
AHS AVS
SDIO1 SDIO2 SDIO3
RESET
DDC_SDA
DDC_SCL
10uF/16V
1 2
4 5 3 8
6 7
9 12 14 15 17 18 20 21 23 24
11 13 19 26 10 16 22 25
30 31 33 34 35 37 38
29 36 41
28
27 32 39 40
42 43
0.1u/6
0.1u/6
C35
C36
U7
XO XI
DPLL_VDD APLL_VDD DPLL_GND APLL_GND
PLL_TEST1 PLL_TEST2
TMDS_TST/PWM1 EXT_RES RX2P RX2N RX1P RX1N RX0P RX0N RXCP RXCN
TMDS_VDD TMDS_VDD TMDS_VDD TMDS_VDD TMDS_GND TMDS_GND TMDS_GND TMDS_GND
B+ B­SOG/ADC_TEST G+ G­R+ R-
ADC_VDD ADC_VDD ADC_VDD
ADC_REFIO
ADC_GND ADC_GND ADC_GND ADC_GND
AHS AVS
R66 100/6
0.1u/6
C37
109
120
3.3V Ground
0.1u/6
C38
72
96
84
3.3V Ground
3.3V Ground
3.3V Ground
3.3V Ground
TCON[3]/SDIO2]
TCON[4]/SDIO[1]
SDIO[0]
SCLK
5450111
C39
57
48
3.3V Ground
3.3V Ground
TCON[2]/SDIO[3]/PWM2
SCSB
515253
NCR71
NCR72
0.1u/6
121
3.3V Power
RESET#
56
0.1u/6
C40
C41
71
83
95
110
3.3V Power
3.3V Power
3.3V Power
3.3V Power
RTD2523
DDCSDA
DDCSCL
47
46
0.1u/6
49
58
3.3V Power
3.3V Power
DDCSCL2
DDCSDA2
126
125
69
98
127
2.5V Power
2.5V Power
TCON[11]/V[0]
114
115
TCON11
TCON10
128
2.5V Power
2.5V Power
TCON[10]/V[1]
TCON[9]/V[2]
TCON[8]/V[3]
118
116
117
TCON8
TCON7
TCON9
C42
97
2.5V Ground
TCON[7]/V[4]
119
TCON6
0.1u/6
2.5V Ground
2.5V Ground
TCON[6]/V[5]
TCON[5]/V[6]
122
TCON5
444570
2.5V Ground
TCON[1]/V[7]
123
C43
124
R2.5DVCCR3DVCC
0.1u/6
0.1u/6
0.1u/6 C45
C44
TCON[12]/COUT/PWM2
PWM0/REFCLK
TCON[13]/COUT/PWM2
AR1P/TCON[0] AR2N/TCON[1] AR2P/TCON[5] AR3N/TCON[6] AR3P/TCON[7] AG1N/TCON[8]
AG1P/TCON[9] AG2N/TCON[10] AG2P/TCON[11]
BCLKN BCLKP
AG3N/TEAN
AG3P/TEAP ACLKN/TEBN ACLKP/TEBP
AB1N/TECN
AB1P/TECP
AB2N/TECLKN AB2P/TECLKP
AB3N/TEDN
AB3P/TEDP
BR1N/TOAN
BR1P/TOAP
BR2N/TOBN
BR2P/TOBP
BR3N/TOCN
BR3P/TOCP
BG1N/TOCLKN BG1P/TOCLKP
BG2N/TODN
BG2P/TODP
TCON[0]/VCLK
TP2
1
TEST POINT
AR1N
BG3N BG3P
BB1N BB1P BB2N BB2P BB3N BB3P
C46
10uF/16V
113 112 55
108 107 106 105 104 103 102 101 100 99
68 67 66 65 64 63 62 61 60 59
94 93 92 91 90 89 88 87 86 85
82 81 80 79 78 77 76 75 74 73
L13 FEB_0805
AR1N AR1P AR2N AR2P AR3N AR3P AG1N AG1P AG2N AG2P
BG3N BG3P BCLKN BCLKP BB1N BB1P BB2N BB2P BB3N BB3P
RXEIN0­RXEIN0+ RXEIN1­RXEIN1+ RXEIN2-
RXEIN2+ RXECKIN­RXECKIN+
RXEIN3-
RXEIN3+
RXOIN0-
RXOIN0+
RXOIN1-
RXOIN1+
RXOIN2-
RXOIN2+ RXOCKIN­RXOCKIN+
RXOIN3-
RXOIN3+
2.5DVCC
VBRI VOLUME
C47
0.1u/6
2.5DVCC
TCON5 TCON6 TCON7 TCON8
TCON9 TCON10 TCON11
FXDIO
22/6R59
XSTB
22/6R60
POL
22/6R61
BXDIO
22/6R62
YCLK
22/6R63
YDIO
22/6R64
YOE
22/6R65
Title
RTD_2523
Size Document Number
RTD2523_DE_A
Custom
Date:
Friday, October 15, 2004
Sheet
48
Rev
A
of
ViewSonic Corporation Confidential - Do Not Copy VX924
72
Page 76
VCPU
Reset circuit
3DVCC
C
3AVCC1
RESET
VCPU
12
3AVCC1
C75
0.1U/6
1 2 3 4 5
D32
NC/ 1N4148
R147
4.7K/6
U8
A0
VCC A1 A2
SCK VSS SI
24LC16
PARAMETER EEPROM
R165
NC/100K/6
13
Q20
2
NC/2N3906
C103
NC/1U/16V
2
1
R166 0/6
R80
8 7
WP
6
2K/6
D33
NC/DAN202U
3
Add Q20,R165,R166,C103,D32,D33 2004/6/16
R81
2K/6
R83 100/6 R92 100/6
PANEL_PW12
VCPU
C86
NC/1U/16V
R106 NC/82K/6
C87 10pF/6 R164 22
Y2
11.0592MHz
PWR_SEL
R41
6.8K/6
VCC12
MUTE
Hot_Plug
STBY
C88 10pF/6
VCPU
IICSCL
IICSDA
LED_R
LED_G
R142 NC
R78
10K/6
LED_G
LED_R
+
C84
22uF/16V
12
11
19
14 13 27 26 16
30 31 32 33
I1
X1
X2
7
RESET
INT0/P3.2
ISCL/P3.5/T1 ISDA/P3.4/T0 P6.0/AD0 P6.1/AD1 P6.2
9
P6.3 P6.4 P6.5 P6.6 P6.7
MTV312M64
C85
0.1u/6
6
NC
5
R79
R93 4.7K/6
VCPU
810
4
NC
VCCVSS
VDD3
DA8/HLFHO
DA9/HALFV
10K/6
R82 4.7K/6
2N3906
43
44
P5.0 P5.1 P5.2
VSYNC
HSYNC
P5.3 P5.4 P5.5 P5.6
P1.0 P1.1 P1.2 P1.3 P1.4 P1.5 P1.6 P1.7
DA7 P4.0 P4.1 P4.2
P3.1/TXD P3.0/RXD
B
13
Q12
2N3906
2
13
Q13
2
MENU SEL PWR DOWN UP RIGHT LEFT
Junction from A change to B
VCPU
3 2 1 42 41 40 34 39 38 17 18 20 21 22 23 24 25 35 36 37 15
28 29
E
3DVCC
R163
4.7K/6
R39 4.7K/6 R40 4.7K/6
33K/6
33K/6
R87
R88
0.1U/6
0.1U/6 C77
C76
VCPU
MENU SEL PWR UP DOWN RIGHT LEFT
R124 100/6 R125 100/6
R89
C78
33K/6
0.1U/6
33K/6
33K/6
R90
R91
0.1U/6
0.1U/6
C79
C80
AVS
VRMT
R109 4.7K/6
R108 4.7K/6
R84
C81
33K/6
0.1U/6
VCPU
R85
C82
R110
4.7K/6
33K/6
0.1U/6
less R94 to CN6 pin 11
R101,R103 net swap
R95 1K/6 R96 1K/6 R97 1K/6 R98 1K/6 R99 1K/6 R100 1K/6 R101 1K/6 R102 220/6 R103 220/6
CN6
10 9 8 7 6 5 4 3 2 1
4501-10-10P-R
TO BUTTON BOARD
VCPU
R111
4.7K/6
TxD RxD
R112
NC
R113
NC
R114
4.7K/6
DDC_SDA DDC_SCL
R115
4.7K/6
2.0mm pitch 90° E&T 4607-11Pin
R116
4.7K/6
R120 NC
5DVCC
PANEL_PW3 SDIO1 SDIO2 SDIO3 RTD_SDO/SDI RTD_SCLK RTD_SCSB
JP1
1 2 3 4
HEADER 4
R38
2K/6
ViewSonic Corporation Confidential - Do Not Copy VX924
73
Title
MCU & BUTTON
Size Document Number
Friday, October 15, 2004
Date:
DISPLAY
58
Sheet of
Rev
A
Page 77
5DVCC
5DVCC
L22
FEB_1206
VCC12
31
GND
L21
NC
R67
82K/6
R70
82K/6
Q9
DTC144EUA
2
PANEL_3VCC
PANEL_5_12VCC
2
C67
2200P/6
Q8 SI2301DS
1
PANEL_PW12
L16 FEB_0805/NV
L20
3
BB3P BB3N
BB2P BB2N
BB1P BB1N
BCLKP BCLKN
BG3P BG3N
RXOIN0­RXOIN0+
RXOCKIN­RXOCKIN+
RXOIN1­RXOIN1+
RXOIN2­RXOIN2+
RXOIN3­RXOIN3+
FEB_0805/NC
C68
2200P/6
DG3
10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30
RSDS_CON30
L18
FEB_0805/NC
R68
10K/6
J1
1
1
2
2
3
3
4
4
5
5
6
6
7
7
8
8
9
9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30
L17
FEB_0805/NC
PANEL_5_12VCC
C69
0.1U/6
1S2
C65
0.1U/6/NC
PANEL_5_12VCC
C70
100U/16V
RXEIN0­RXEIN0+
RXECKIN­RXECKIN+
RXEIN1­RXEIN1+
RXEIN2­RXEIN2+
RXEIN3­RXEIN3+
AG2P AG2N
AG1P AG1N
AR3P AR3N
AR2P AR2N
AR1P AR1N
FXDIO XSTB POL BXDIO
YCLK YDIO YOE
0.1U/6/NC
C66
J2
1 2 3 4 5 6 7 8
9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50
RSDS_CON50/NC
C73
NC/0.1U/6
PANEL_3VCC
PANEL_3VCC
C74
NC/100U/16V
RXOIN0­RXOCKIN­RXOIN1­DGND RXOIN2­RXOIN3­RXEIN0­DGND RXECKIN­RXEIN1­RXEIN2­RXEIN3-
DGND
PANEL_5_12VCC
L30 NC/FEB_1206
PANEL_3VCC
PANEL_5_12VCC
11 13 15 17 19 21 23 25 27 29
1 3 5 7 9
CN5
1 3 5 7 9 11 13 15 17 19 21 23 25 27 29
1841 30P
2 4 6
8 10 12 14 16 18 20 22 24 26 28 30
RXOIN0+
2
RXOCKIN+
4
RXOIN1+
6
DGND
8
RXOIN2+
10
RXOIN3+
12
RXEIN0+
14
DGND
16
RXECKIN+
18
RXEIN1+
20
RXEIN2+
22
RXEIN3+
24
DGND
26
PANEL_5_12VCC
28
PANEL_5_12VCC
30
/4/14
3DVCC
R75
NC/82K/6
R77
NC/10K/6
31
Q11 NC/DTC144EUA
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50
NC/2200P/6
2
C
2
B
C71
3
1
Q10 NC/SI2301DS
1
PANEL_PW3
3
R76
C72
NC/10K/6
NC/2200P/6
2
E
If panel is 3.3V LVDS IF, L30 must add the part 2004
ViewSonic Corporation Confidential - Do Not Copy VX924
74
Title
<Title>
Size Document Number
Date:
PANEL INTERFACE
<Doc>
C
Friday, October 15, 2004
Sheet
Rev
68
of
Page 78
5V
L1
CX000800000/8
LVDS_GND
C1
U1
3.3V
0.8A Max
23
VOUTVIN
1
ADJ/GND
AIC1084/TO252
10uF/8
C2
0.1uF/6
R2
330/6 1%
H1
2 3 4
9 8
1
7
5 6
MTH276D126
R1
200/6 1%
H2
2 3
1
4 5 6
MTH276D126
9 8 7
C3
10uF/8
C4
0.1uF/6
LVDS_GND LVDS_GNDLVDS_GND LVDS_GND
H3
2 3
1
4 5 6
MTH276D126
ViewSonic Corporation Confidential - Do Not Copy VX924
75
9 8 7
LVDS_GNDLVDS_GND
Title
<Title>
Size Document Number
<Doc>
A
Date: Sheet
Friday, February 25, 2005
Rev
of
Page 79
SDRAM1_3.3V
CONFIG SETTING
3.3V
R14 1K/6
R15 1K/6/NC
R16 1K/6/NC
R17 1K/6/NC
R19 1K/6/NC
D_E_SD1_B3 D_E_SD1_B4
D_E_SD1_B5 D_E_SD1_B6
D_E_SD1_B7 D_E_SD1_G3
D_E_SD1_G4 D_E_SD1_G5
SD_DQM0 SD1_WE SD_CAS SD_RAS SD_CS SD_BA0 SD_A10 SD_A0 SD_A1 SD_A2 SD_A3
Extrenal ROM Download Connector
External ROM
U3
SPI_CS
1
SPI_SO
2 3 4 5
DGND
RESET circuit
3.3V
R8 10K/6
RESET
C5
10uF/8
DGND
OD_EN
SEL_ROM_1
TAB_SEL_0
TAB_SEL_1
R18 1K/6/NC
TAB_SEL_2
U6
1
Vcc
2
DQ0
3
DQ1
4
VssQ
5
DQ2
6
DQ3
7
VccQ
8
DQ4
9
DQ5
10
VssQ
11
DQ6
12
DQ7
13
VccQ
14
LDQM
15
WE
16
CAS
17
RAS
18
CS
19
BA
20
A10
21
A0
22
A1
23
A2
24
A3
25 26
Vcc
DRAM_16M
CS SO WP GND SI
SPI_AT25F512
SEL_ROM_2
HOLD
DQ15 DQ14
VssQ DQ11 DQ10
VccQ DQ11 DQ10
VssQ
VccQ
UDQM
SPI_SCK SPI_CS RESET
VCC
SCK
D1
1SS355/NC
Vss
DQ9 DQ8
NC
CLK CKE
NC
A9 A8 A7 A6 A5 A4
Vss
8 7 6
50 49 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 32 31 30 29 28 27
20321-06-SMD/NC
3.3V
D_E_SD1_R7
D_E_SD1_R6 D_E_SD1_R5
D_E_SD1_R4 D_E_SD1_R3
D_E_SD1_G7 D_E_SD1_G6
SD_DQM0 SDRAM_CLOCK
SD_A9 SD_A8 SD_A7 SD_A6 SD_A5 SD_A4
JP3
56 34 12
SPI_SCK SPI_SI
SDRAM1_3.3V
56 34 12
SPI EEPROM
SPI_SI SPI_SO
DGND
D_O_SD1_B3 D_O_SD1_B4
D_O_SD1_B5 D_O_SD1_B6
D_O_SD1_B7 D_O_SD1_G3
D_O_SD1_G4 D_O_SD1_G5
SD_DQM0 SD1_WE SD_CAS SD_RAS SD_CS SD_BA0 SD_A10 SD_A0 SD_A1 SD_A2 SD_A3
U7
1
Vss
Vcc
2
DQ15
DQ0
3
DQ14
DQ1
4
VssQ
VssQ
5
DQ11
DQ2
6
DQ10
DQ3
7
VccQ
VccQ
8
DQ11
DQ4
9
DQ10
DQ5
10
VssQ
VssQ
11
DQ9
DQ6
12
DQ8
DQ7
13
VccQ
VccQ
14
LDQM
15
UDQM
WE
16
CLK
CAS
17
CKE
RAS
18
CS
19
BA
20
A10
21
A0
22
A1
23
A2
24
A3
25 26
Vss
Vcc
DRAM_16M
JP2
TXO0­TXO1­TXO2-
TXOC­TXO3­TXE0-
TXE1­TXE2­TXEC-
TXE3-
170
TXE3-
VCC
O_SD1_R3
D_O_SD1_R3
TXE3+
168
169
TXE3+
RESERVED
O_SD1_R5
O_SD1_R4
1234
PR15
33x4
D_O_SD1_R4
165
166
167
LVDS_VCC
LVDS_GND
LVDS_GND
ODD_SD1_R5
ODD_SD1_R6
ODD_SD1_R7
SD_DQM0
O_SD1_R7
O_SD1_R6
O_SD1_R5
5 6 7 8
D_O_SD1_R5
LVDS_GND
O_SD2_R7
O_SD2_R6
O_SD2_R5
O_SD2_R4
161
162
163
164
LVDS_GND
ODD_SD2_R5
ODD_SD2_R6
ODD_SD2_R7
O_SD2_BR
SDRAM_DQM_0
SDRAM_1_WE
SDRAM_DQM_1
SDRAM_CAS
100
SD_CAS
SD_DQM1
SD1_WE
SD_RAS
O_SD1_R6
O_SD1_R7
1234
PR16 33x4
D_O_SD1_R6
D_O_SD1_R7
TXE3-
OD_3.3V
O_SD2_R3
O_SD2_G7
158
159
160
ODD_SD2_R3
ODD_SD2_R4
ODD_SD2_G7
EVEN_SD2_R7
EVEN_SD2_R6 EVEN_SD2_R5
E_SD2_R O_SD2_B
EVEN_SD2_R4 EVEN_SD2_R3 EVEN_SD2_G7 EVEN_SD2_G6 EVEN_SD2_G5 EVEN_SD2_G4
EVEN_SD2_G3 EVEN_SD2_B7 EVEN_SD2_B6 EVEN_SD2_B5 EVEN_SD2_B4
E_SD2_B E_SD2_G
EVEN_SD2_B3 SDRAM_2_WE
SDRAM_RAS
SDRAM_CLK
SDRAM_CS
101
102
103
SD_CLK
SD_CS
DGND
U4
157
VTIO3601_LQFP
VCC
GND
ODD_SD2_G6 ODD_SD2_G5 ODD_SD2_G4 ODD_SD2_G3 ODD_SD2_B7 ODD_SD2_B6 ODD_SD2_B5 ODD_SD2_B4 ODD_SD2_B3
RESERVED
RESERVED
RESERVED
RESERVED SDRAM_A3 SDRAM_A2 SDRAM_A4 SDRAM_A1 SDRAM_A5 SDRAM_A0 SDRAM_A6
SDRAM_A10
SDRAM_A7
SDRAM_BA1
SDRAM_A8
SDRAM_BA0
SDRAM_A9
GND
VCC
104
VCC GND
VCC GND
VCC GND
VCC GND
VCC GND
R21
33/6
JP1
RXO0-
1
1
RXO1-
3
3
RXO2-
5
5
7
7
RXOC-
9
9
RXO3-
11
11
RXE0-
13
13
15
15
RXE1-
17
17
RXE2-
19
19
RXEC-
21
21
RXE3-
23
23
25
25
27
27
29
29
DGND
1841 30P
R20 0/1206
LVDS_GND
LVDS_GND
50 49
D_O_SD1_R7
48 47
D_O_SD1_R6
46
D_O_SD1_R5
45 44
D_O_SD1_R4
43
D_O_SD1_R3
42 41
D_O_SD1_G7
40
D_O_SD1_G6
39 38 37
NC
SD_DQM0
36
SDRAM_CLOCK
35 34 33
NC
SD_A9
32
A9
SD_A8
31
A8
SD_A7
30
A7
SD_A6
29
A6
SD_A5
28
A5
SD_A4
27
A4
DGNDDGND
R5 100/6 1%
10 12 14 16 18 20 22 24 26 28 30
R11 100/6 1%
RXO0+
2
2
RXO1+
4
4
RXO2+
6
6
8
8
RXOC+
10
RXO3+
12
RXE0+
14 16
RXE1+
18
RXE2+
20
RXEC+
22
RXE3+
24 26 28 30
LVDS_GND
R3 100/6 1%
R6 100/6 1%
R9 100/6 1%
R12 100/6 1%
R7 100/6 1%
5V
R4 100/6 1%
R10 100/6 1%
R13 100/6 1%
LVDS_GND
RXO0­RXO0+ RXO1-
RXO1+ RXO2­RXO2+ RXOC-
RXOC+
RXO3­RXO3+
RXE0-
RXE0+ RXE1­RXE1+ RXE2­RXE2+ RXEC-
RXEC+
RXE3­RXE3+
LVDS_3.3V
SEL_ROM_1 SEL_ROM_2
RESET TAB_SEL_1 TAB_SEL_2 TAB_SEL_0 OD_EN SPI_SCK SPI_SI SPI_CS SPI_SO
TXO3-
TXOC-
TXO0-
TXO1-
TXO2-
TXO3+
TXOC+
TXO1+
TXO2+
TXO0+
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
RESERVED
RESERVED
RESERVED
RESERVED
1
LVDS_VCC
2
LVDS_VCC
3
LVDS_VCC
4
RXO0-
5
Receiver_ODD Receiver_EVEN Config SPI
RXO0+
6
RXO1-
7
RXO1+
8
RXO2-
9
RXO2+
10
RXOC-
11
RXOC+
12
RXO3-
13
RXO3+
14
LVDS_GND
15
LVDS_GND
16
LVDS_GND
17
LVDS_GND
18
LVDS_VCC
19
LVDS_VCC
20
LVDS_VCC
21
RXE0-
22
RXE0+
23
RXE1-
24
RXE1+
25
RXE2-
26
RXE2+
27
RXEC-
28
RXEC+
29
RXE3-
30
RXE3+
31
LVDS_GND
32
LVDS_GND
33
LVDS_GND
34
LVDS_GND
35
RESERVED
36
RESERVED
37
SEL_ROM_1
38
SEL_ROM_2
39
RSTN
40
TAB_SEL_1
41
TAB_SEL_2
42
TAB_SEL_0
43
OD_EN
44
SPI_CLK
45
SPI_SI
46
SPI_CS
47
SPI_SO
48
PAD_TEST
E_SD1_B E_SD1_
49
PAD_TCLK
50
RESERVED
51
VCC
52
GND
GND
VCC
EVEN_SD1_B3
EVEN_SD1_B4
5354555657585960616263646566676869707172737879808174757677828384858687888990919293949596979899
E_SD1_B3
E_SD1_B5
E_SD1_B4
E_SD1_B3
E_SD1_B4
E_SD1_B5
E_SD1_B6
E_SD1_B7
E_SD1_G3
E_SD1_G4
E_SD1_G5
1234
1234
PR9
PR10
33x4
33x4
5 6 7 8
5 6 7 8
D_E_SD1_B3
D_E_SD1_B4
D_E_SD1_B5
D_E_SD1_B6
D_E_SD1_B7
D_E_SD1_G3
D_E_SD1_G4
D_E_SD1_G5
LVDS_VCC
LVDS_GND
RESERVED
RESERVED
EVEN_SD1_B5
EVEN_SD1_B6
EVEN_SD1_B7
EVEN_SD1_G3
E_SD1_G3
E_SD1_B7
E_SD1_B6
E_SD1_G6
E_SD1_G7
E_SD1_R3
5 6 7 8
D_E_SD1_G6
D_E_SD1_G7
D_E_SD1_R3
LVDS_VCC
LVDS_GND
LVDS_GND
G E_SD1_R
EVEN_SD1_G4
EVEN_SD1_G5
EVEN_SD1_G6
E_SD1_G5
E_SD1_G4
E_SD1_G6
E_SD1_R4
1234
PR11
33x4
D_E_SD1_R4
E_SD1_G7
TXO2-
TXO1-
TXO0-
TXOC-
TXO2+
TXO1+
TXO0+
LVDS_VCC
Transmitter_ODD
VTIO3601
EVEN_SD1_G7
EVEN_SD1_R3
RESERVED
GND
VCC
RESERVED
EVEN_SD1_R4
EVEN_SD1_R5
E_SD1_R3
E_SD1_R5
E_SD1_R4
E_SD1_R5
E_SD1_R6
E_SD1_R7
1234
PR12
33x4
5 6 7 8
D_E_SD1_R5
D_E_SD1_R6
D_E_SD1_R7
TXO3-
TXO3+
TXOC+
EVEN_SD1_R6
EVEN_SD1_R7
ODD_SD1_B3
E_SD1_R6
E_SD1_R7
O_SD1_B3
O_SD1_B3
5 6 7 8
D_O_SD1_B3
LVDS_GND
LVDS_GND
O_SD1_B
ODD_SD1_B4
ODD_SD1_B5
O_SD1_B5
O_SD1_B4
O_SD1_B4
O_SD1_B5
D_O_SD1_B4
D_O_SD1_B5
182
183
184
LVDS_VCC
LVDS_GND
RESERVED
ODD_SD1_B6
O_SD1_B6
O_SD1_B6
1234
PR13
33x4
D_O_SD1_B6
180
181
LVDS_VCC
LVDS_GND
GND
VCC
O_SD1_B7
5 6 7 8
D_O_SD1_B7
TXE0+
TXE0-
178
179
TXE0-
LVDS_GND
RESERVED
ODD_SD1_B7
O_SD1_B7
O_SD1_G3
O_SD1_G3
O_SD1_G4D_O_SD1_G4
D_O_SD1_G3
TXE1+
TXE2-
TXE1-
174
175
176
177
TXE2-
TXE1-
TXE1+
TXE0+
LVDS_VCC
Transmitter_EVEN
ODD_SD1_G3
ODD_SD1_G4
ODD_SD1_G5
ODD_SD1_G6
ODD_SD1_G7
O_SD1_G6
O_SD1_G5
O_SD1_G4
O_SD1_G7
O_SD1_G5
1234
PR14 33x4
D_O_SD1_G5
TXE2+
TXEC-
172
173
TXEC-
TXE2+
O_SD1_RO_SD1_G
ODD_SD1_R3
ODD_SD1_R4
O_SD1_R4
O_SD1_R3
O_SD1_G6
5 6 7 8
D_O_SD1_G6
TXEC+
171
TXEC+
GND
O_SD1_G7
D_O_SD1_G7
TXO0+
1
2
1
2
TXO1+
3
4
3
4
TXO2+
5
6
5
6
7
8
7
8
TXOC+
9
10
9
10
TXO3+
11
12
11
12
TXE0+
13
14
13
14
15
16
15
16
TXE1+
17
18
17
18
TXE2+
19
20
19
20
TXEC+
21
22
21
22
TXE3+
23
24
23
24
25
26
25
26
27
28
27
28
29
30
29
30
20321-30-SMD
LVDS_GND
156 155
O_SD2_G6
154
O_SD2_G5
153
O_SD2_G4
152
O_SD2_G3
151
O_SD2_B7
150
O_SD2_B6
149
O_SD2_B5
148
O_SD2_B4
147
O_SD2_B3
146
E_SD2_R7
145 144 143 142
E_SD2_R6
141
E_SD2_R5
140
E_SD2_R4
139
E_SD2_R3
138
E_SD2_G7
137
E_SD2_G6
136
E_SD2_G5
135
E_SD2_G4
134 133 132 131
E_SD2_G3
130
E_SD2_B7
129
E_SD2_B6
128
E_SD2_B5
127
E_SD2_B4
126
E_SD2_B3
125
SD2_WE
124 123 122 121 120
SD_A3
119
SD_A2
118
SD_A4
117
SD_A1
116
SD_A5
115
SD_A0
114
SD_A6
113
SD_A10
112
SD_A7
111 110
SD_A8
109
SD_BA0
108
SD_A9
107 106 105
O_SD2_R7 O_SD2_R6 O_SD2_R5
O_SD2_R4 O_SD2_R3 O_SD2_G7 O_SD2_G6
O_SD2_G5 O_SD2_G4 O_SD2_G3 O_SD2_B7
O_SD2_B6 O_SD2_B5 O_SD2_B4 O_SD2_B3
E_SD2_R7 E_SD2_R6 E_SD2_R5
E_SD2_R4 E_SD2_R3 E_SD2_G7 E_SD2_G6
E_SD2_G5 E_SD2_G4 E_SD2_G3 E_SD2_B7
E_SD2_B6 E_SD2_B5 E_SD2_B4 E_SD2_B3
5V
1 2 3 4 5
PR2
1 2 3 4 5
PR3
1 2 3 4 5
PR4
1 2 3 4 5
PR5
1 2 3 4 5
PR6
1 2 3 4 5
PR7
1 2 3 4 5
PR8
1 2 3 4 5
PR1
8
D_O_SD2_R7
7
D_O_SD2_R6
6
D_O_SD2_R5
33x4
D_O_SD2_R4
8
D_O_SD2_R3
7
D_O_SD2_G7
6
D_O_SD2_G6
33x4
D_O_SD2_G5
8
D_O_SD2_G4
7
D_O_SD2_G3
6
D_O_SD2_B7
33x4
D_O_SD2_B6
8
D_O_SD2_B5
7
D_O_SD2_B4
6
D_O_SD2_B3
33x4
8
D_E_SD2_R7
7
D_E_SD2_R6
6
D_E_SD2_R5
33x4
D_E_SD2_R4
8
D_E_SD2_R3
7
D_E_SD2_G7
6
D_E_SD2_G6
33x4
D_E_SD2_G5
8
D_E_SD2_G4
7
D_E_SD2_G3
6
D_E_SD2_B7
33x4
D_E_SD2_B6
8
D_E_SD2_B5
7
D_E_SD2_B4
6
D_E_SD2_B3
33x4
SD_CLKSDRAM_CLOCK
SDRAM2_3.3V
1
D_O_SD2_G5
2
D_O_SD2_G4
3 4
D_O_SD2_G3
5
D_O_SD2_B7
6 7
D_O_SD2_B6
8
D_O_SD2_B5
9
10
D_O_SD2_B4
11
D_O_SD2_B3
12 13
SD_DQM1
14
SD2_WE
15
SD_CAS
16
SD_RAS
17
SD_CS
18
SD_BA0
19
SD_A10
20
SD_A0
21
SD_A1
22
SD_A2
23
SD_A3
24 25 26
SDRAM2_3.3V
1
D_E_SD2_G5
2
D_E_SD2_G4
3 4
D_E_SD2_G3
5
D_E_SD2_B7
6 7
D_E_SD2_B6
8
D_E_SD2_B5
9
10
D_E_SD2_B4
11
D_E_SD2_B3
12 13
SD_DQM1
14
SD2_WE
15
SD_CAS
16
SD_RAS
17
SD_CS
18
SD_BA0
19
SD_A10
20
SD_A0
21
SD_A1
22
SD_A2
23
SD_A3
24 25 26
3.3V
3.3V
3.3V SDRAM1_3.3V
3.3V
OD_3.3V
L2
CX000800000/8
10uF/8
10uF/8
C18
C19
DGND
LVDS_3.3V
L3
CX000800000/8
10uF/8
10uF/8
C33
C32
LVDS_GND LVDS_GND
L4
CX000800000/8
L5
CX000800000/8
DGND
SDRAM2_3.3V
DGND
10uF/8
10uF/8
C59
C58
10uF/8
C74
C21
C22
C75
U2
U5
Vcc DQ0 DQ1 VssQ DQ2 DQ3 VccQ DQ4 DQ5 VssQ DQ6 DQ7 VccQ LDQM WE CAS RAS CS BA A10 A0 A1 A2 A3 Vcc
Vcc DQ0 DQ1 VssQ DQ2 DQ3 VccQ DQ4 DQ5 VssQ DQ6 DQ7 VccQ LDQM WE CAS RAS CS BA A10 A0 A1 A2 A3 Vcc
10uF/8
10uF/8
C23
10uF/8
DRAM_16M
DRAM_16M
C6
10uF/8
C60
10uF/8
C24
50
Vss
49
DQ15
D_O_SD2_G6
48
DQ14
47
VssQ
D_O_SD2_G7
46
DQ11
D_O_SD2_R3
45
DQ10
44
VccQ
D_O_SD2_R4
43
DQ11
D_O_SD2_R5
42
DQ10
41
VssQ
D_O_SD2_R6
40
DQ9
D_O_SD2_R7
39
DQ8
38
VccQ
37
NC
SD_DQM1
36
UDQM
SDRAM_CLOCK
35
CLK
34
CKE
33
NC
SD_A9
32
A9
SD_A8
31
A8
SD_A7
30
A7
SD_A6
29
A6
SD_A5
28
A5
SD_A4
27
A4
Vss
DGND
50
Vss
49
DQ15
D_E_SD2_G6
48
DQ14
47
VssQ
D_E_SD2_G7
46
DQ11
D_E_SD2_R3
45
DQ10
44
VccQ
D_E_SD2_R4
43
DQ11
D_E_SD2_R5
42
DQ10
41
VssQ
D_E_SD2_R6
40
DQ9
D_E_SD2_R7
39
DQ8
38
VccQ
37
NC
SD_DQM1
36
UDQM
SDRAM_CLOCK
35
CLK
34
CKE
33
NC
SD_A9
32
A9
SD_A8
31
A8
SD_A7
30
A7
SD_A6
29
A6
SD_A5
28
A5
SD_A4
27
A4
Vss
DGND
0.1uF/6
0.1uF/6
0.1uF/6
0.1uF/6
0.1uF/6
0.1uF/6
0.1uF/6
C9
0.1uF/6
0.1uF/6
C7
0.1uF/6
C8
0.1uF/6 C10
C11
C12
C13
0.1uF/6
0.1uF/6
0.1uF/6
0.1uF/6 C35
C36
C34
0.1uF/6
0.1uF/6
0.1uF/6 C61
C62
0.1uF/6
0.1uF/6
C77
C76
0.1uF/6
0.1uF/6
0.1uF/6 C39
C37
C40
C38
0.1uF/6
0.1uF/6
0.1uF/6
0.1uF/6 C66
C65
C64
C63
C67
0.1uF/6
0.1uF/6
0.1uF/6
0.1uF/6
0.1uF/6
C80
C78
C82
C79
C81
0.1uF/6
C14
C15
C16
C17
DGND
0.1uF/6
0.1uF/6
0.1uF/6
0.1uF/6
0.1uF/6 C44
C43
C41
C45
C42
0.1uF/6
0.1uF/6
0.1uF/6
0.1uF/6
0.1uF/6
0.1uF/6 C69
C68
0.1uF/6
0.1uF/6
C83
C84
0.1uF/6
C70
C71
C72
C73
0.1uF/6
0.1uF/6
0.1uF/6
0.1uF/6
0.1uF/6 C88
C85
C86
C89
C87
VTIO3601_16Mbx4 Ref. Circuit
ViewSonic Corporation Confidential - Do Not Copy VX924
76
Title
Size Document Number
<Doc>A1
Date:
Friday, February 25, 2005
Sheet
Rev
22
of
Page 80
GND
5DVCC
3EC
12
RTD 3DVCC
ADC_ 3AVCC RTD 3PVCC
LVDS_3AVCC
3DVCC
0.1u/6
C3
2.5DVCC
10uF/16V
5DVCC
3DVCC
3AVCC1
3PVCC
3AVCC2
2.5DVCC
0.1u/6
C12
RTD 2.5DVCC
與共
U10 U3 layout 2004/4/16
D1
1SS355
C2 1u/6
VCC12
GND
GND
R2
0/1206
C8
0.1u/6
U2
8
BOOST
7
IS
6
VCC
AIC1563
R11 3K/6 1%
C10 2200p/6
1K/6 1%
R12
R11:3K 1% ohm, R12:1K 1%
GND
ohm -->output:5V; R11:3.6K 1% ohm, R12:2.2K 1% ohm-->output 3.3V
1
DC
DE
CF
GNDFB
R4 47/6
2
R5 330K/6
3
45
GND
GND
C9
120p/6
1SS355
D2
Q2
R7
240K/6 1%
1
R9 1K/6
3 2
MMST3906
7681
Q1
NDS9410A/SO
GND
C7
1 3
0.1u/6
L2
47UH
D3
RB081L-20
12
EC4
330u/16V
234 5
U1 AIC1117CY
3
VIN
+
EC2
10uF/16V
U3 AIC1117CY
3
VIN
+
10uF/16V
EC5
VOUT
GND
1
VOUT
GND
1
+
0.1u/6
C1
EC1
10uF/16V
2
200/6 1%
R3
+
10uF/16V
EC3
R6
330/6 1%
2
R15
+
200/6 1%
EC6
R17
200/6 1%
CN1 CONN 4x2-R
1 2
4
3 5 6
8
GND
DGND
C102
12V
L3
1U/6
FUSE1 0
1 2
12
10K/6
C4
0.1u/6
MMST3906
C11
C13
1U/8
3DVCC
3DVCC
R8
R10
0/6
10K/6
Q3
R14
0.1U/6
10K/6/NC
R18 4.7K/6
R1,L1
C5
0.1u/6
R13 1K/6
3DVCC
R16 1K/6
3
2
1
Q4
SN7002E
VCC12
C6
330u/16V
VBRI
VRMT
DSUB_5V
D30
1N4148
3DVCC
RTD 3DVCC
ADC_ 3AVCC
RTD 3PVCC
LVDS_3AVCC
Modify
Q18 MMBT3906
D31
1N4148
R143
4.7K/6
3DVCC
3AVCC1
3PVCC
3AVCC2
MMBT3906
R144
4.7K/6
3DVCC
Q19
NC/CX201209805/8 L27
CX201209805/8
L28
C100
0.1u/6
VCPU
C101 NC/6
L29
FEB/1206/NC
U10
3 1
VIN VOUT
2
GND
AIC1739/NC
2.5DVCC
2.5DVCC
RTD 2.5DVCC
3.3V-->2.5V regulator for 3.3V system power, no 5V 2004/4/14
Title
<Title>
Size Document Number
Custom
Date:
POWER
<Doc>
Friday, October 15, 2004
Sheet
88
Rev
of
ViewSonic Corporation Confidential - Do Not Copy VX924
77
Page 81
11. PCB Layout Diagrams
Control Board
Main Board
ViewSonic Corporation Confidential
78
-
Do Not Copy VX924
Page 82
*Readers Response*
Dear Readers:
Thank you in advance for your feedback on our Service Manual, which allows continuous improvement
of our products. We would appreciate your completion of the Assessment Matrix below, for return to
ViewSonic Corporation.
A. What do you think about the content of this Service Manual?
Assessment
1.
Precautions and Safety Notices
2. Specification
Front Panel Function Control Description
3.
4. Circuit Description
5.
Adjustment Procedure
6. Troubleshooting Flow Chart
7. Recommended Spare Parts List
8. Exploded Diagram and Exploded Parts List
9. Block Diagram
10. Schematic Diagrams
11. PCB Layout Diagrams
tinU riaF daB
dooGtnellecxE
B. Are you satisfied with this Service Manual?
metI tnellecxE dooG riaF daB
.1
Service Manual Content
.2
Service Manual Layout
.3
The form and listing
C. Do you have any other opinions or suggestions regarding this service manual?
Readers basic data:
Name: Title:
Company: Add.:
Tel: E-mail:
After completing this form, please return it to ViewSonic Quality Assurance
1-909-839-7943. (marc.maupin@viewsonic.com)
You may also e-mail any suggestions to the Director, Quality Systems & Processes
Fax:
in the USA at facsimile
ViewSonic Corporation Confidential
79
-
Do Not Copy VX924
Loading...