ViewSonic ““381 Brea Canyon Road, Walnut, California 91789 USA - (800) 888-8583
Page 2
Copyright
Copyright¤ 2003 by ViewSonic Corporation. All rights reserved. No part of this publication may be
reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language or
computer language, in any form or by any means, electronic, mechanical, magnetic, optical, chemical,
manual or otherwise, without the prior written permission of ViewSonic Corporation.
Disclaimer
ViewSonic makes no representations or warranties, either expressed or implied, with respect to the
contents hereof and specifically disclaims any warranty of merchantability or fitness for any particular
purpose. Further, ViewSonic reserves the right to revise this publication and to make changes from time
to time in the contents hereof without obligation of ViewSonic to notify any person of such revision or
changes.
Trademarks
ViewSonic is a registered trademark of ViewSonic Corporation.
All other trademarks used within this document are the property of their respective owners.
Revision History
RevisionDateDescription Of ChangesApproval
1a02/11/03Initial Reversion DCN-3047 C.Shen
ViewSonic Corporation
j!
Confidential – Do Not Copy VX800-3
Page 3
PRECAUTIONS AND NOTICES
Prior to using this manual, please ensure that you have carefully followed all the procedures
outlined in the user manual for this product.
Read all of these instructions.
z
Save these instructions for later use.
z
Follow all warnings and instructions marked on the product.
z
Do not use this product near water.
z
This display should be installed on a solid horizontal base.
z
When cleaning, use only a neutral detergent cleaner with a soft damp cloth. Do not spray
z
with liquid or aerosol cleaners.
Do not expose this display to direct sunlight or heat. Hot air may cause damage to the cabinet
z
and other parts.
Adequate ventilation must be maintained to ensure reliable and continued operation and to
z
protect the display from overheating. Do not block ventilation slots and openings with objects or
install the display in a place where ventilation may be hindered.
Do not install this display near a motor or transformer where strong magnetism is generated.
z
Images on the display will become distorted and the color irregular.
Do not allow metal pieces or objects of any kind fall into the display from ventilation holes.
z
Slots and openings in the cabinet and the back or bottom are provided for ventilation, to ensure reliable
operation of the product and to protect it from overheating, those openings must not be blocked or
covered. The openings should never be blocked by placing the product on a bed, sofa, rug, or other
similar surface. This product should never be placed near or over a radiator or heat register. This
product should not be placed in a built-in installation unless proper ventilation is provided.
9.1 Recommended Spare Parts List ....................................................................................... 67
9.2 Complete Parts List .............................................................................................................69
ViewSonic Corporation
wj!
Confidential – Do Not Copy VX800-3
Page 6
I. Engineering Specifications.
1.1 Scope
The following specifications are applicable to model VX800-3 18 inch color LCD monitor.
General Description (Quick Reference)
LCD
Input Signals RGB
Chi-Mei 18.0” SXGA TFT- MVA (premium)
Size
Effective Display Size
Pixel Pitch
Resolution
Brightness
Contrast Ratio
Color
Viewing Angle
18.0 inches diagonal
357.12 mm X 285.696 mm (typical)
0.279 mm X 0.279 mm
1280 x 1024 dot (SXGA)
250 cd / m² (typ.), 200 min.
500:1(typ.), 400:1(min.)
16,777,216
Up 80° Down 80° (min.)
Left 80° Right 80°(min.)
CR>10:1
Surface treatment
Analog 0.7 Vp-p /
75ȍ
Anti-Glare
Positive Polarity
TTL level
Separate sync.
Composite sync
Digital
Sync-On-Green
TMDS.
Input connector Analog mini D-sub 15 pin x 1
Digital DVI-D x 1
Audio min-Din 2 channel x 2
Micro-phone jack
* These functions are not available in Digital Mode.
Memory Recall is to recall the following functions to factory setting: Contrast, Brightness, H Size,
H/V Position, Color Temperature @ 6500K, OSD Position, Sharpness, & OSD Timeout.
OSD Auto Save
The OSD shall save new settings when it is turned off by the user or when it times out. There
shall not be a separate save.
ViewSonic Corporation
41!
Confidential – Do Not Copy VX800-3
Page 36
3. Circuit Description
L17KMW/L18HMW 05AAW LCD MONITOR BLOCK DIAGRAM
3.3V2.5V
CN601
HD-15
15PINS
CN600
DVI-D
24PINS
5V
IC602
HD-15
DDC
EEPROM
5V
IC600
DVI-D
DDC
EEPROM
ADAPTER
PWR
RGB
HS
VS
VGA_SDA
VGA_SCL
DVI_SDA
DVI_SCL
VGA_SDA
VGA_SCL
DVI_SDA
DVI_SCL
12V
POWER
I/F
IC603
74F14
ANALOG I/P
Hsync
Vsync
IC400
DISPLAY ENGINE
5V
12V
5V
DVDD2.5
DVDD3.3
LVDS3.3
GM5120
ADC+DVI+SCALER+MCU
DIGITAL
I/P X 8PINS
VGA_SDA
VGA_SCL
DVI_SDA
DVI_SCL
CN302
AUDIO
BACKLIGHT_EN
BACKLIGHT_CONTROL
PANEL_EN
SDA
SCL
3.3V3.3V
IC500
LVDS
3.3V3.3V
IC501
LVDSLVDS
IC402
FLASH
EEPROM
(F/W)
5V
IC404
DATA
EEPROM
KEY
BOARD
5V
IC502
SI9933ADY
VPNL
5V
12V
INVERTER
CN500
LVDS
OUT
CON
LCD
PANEL
ViewSonic Corporation
Confidential – Do NotCopy VX800-3
42!
Page 37
3.1. Interface Board
1.1 Power Supply (DC/DC Converter)
IC100 is a linear regulator that converts a 12V DC input voltage into regulated and stable
output voltages of 5V respectively.
1.2 Micro-Controller
IC400 (scaler) built-in a micro-controller and extra a flash ROM (IC402---39SF010). It plays a
major role in the digital control of the LCD monitor. IC400 acts as a Key control, DPMS power
saving control, auto-detect controller, and controller of IC400 to do image process.
Pin 114 controls Inverter enable or disable
Pin 113 enable vcc for panel
Pin 125 send a HI signal when audio is invalid
send a LOW signal when audio is valid
pin 5 receive HI signal from IC401 pin 3 to reset
Pin 1, 4, 39, 43, 46, 47, 125, 206 make key function operate when press key button
(receive LOW signal from key button.)
2
Pin 51, 52 communicate with IC404 (EEPROM) by I
C
Pin 48 detect audio in
Pin 51, 52 do ISP (in-system program)
Pin 40 controls the brightness of panel
Pin 41, 42 controls LED (orange and green) on /off
Pin 123 control audio boards 12V on/off
Pin 126 control IC500, IC501 (LVDS Transmitter) on/off.
ViewSonic Corporation
43!
Confidential – Do Not Copy VX800-3
Page 38
1.3. Image Processor
IC400 (gm5120) is an all-in-one image processor for displays with a dual (analog and digital)
interface supporting resolutions up to SXGA. It provides integrated ADC/PLL and a DVI
compliant TMDS receiver and MCU, a high quality zoom and shrink scaling engine, an
on-screen display (OSD) controller, a microprocessor and many other functions in a single
device. This high level of integration enables simple, flexible, cost-effective solutions featuring
fewer required components.
The gm5120 chip has three ADC’s (analog-to-digital converters), one for each color
(red, green, and blue) and supports digital separate sync (HSYNC/VSYNC), digital
composite sync, and analog composite sync (also known as sync-on-green, or SOG). All
sync types are supported without the need for external sync separation / extraction circuits.
The gm5120 features four clock inputs. All additional clocks are internal clocks derived
from one or more of these four, using Direct Digital Synthesis (DDS).
TCLK is generated using an external crystal (recommended) or an external clock
oscillator. (1) Input Clock (TCLK). The external connection to the oscillator is via the TCLK
and XTAL pads. A 14.3MHz crystal source is recommended, as internal PLL and logic
circuits derive the required clock frequencies from this single source by default. Other
crystal frequencies may be used, but require custom bootstrapping and programming. In
lieu of using a crystal oscillator, XTAL can be driven by a single-ended TTL/CMOS input
clock (e.g. for testing of the IC) – the TCLK pin should be grounded through a 2.7k pull
down resistor to maintain the correct duty cycle for the clock.
ViewSonic Corporation
44!
Confidential – Do Not Copy VX800-3
Page 39
(2) TMDS Differential Input Clock (RC+ and RC-)
(3) Video Clock (VCLK) input pin
(4) Host Interface Transfer Clock (HCLK for 6-Wire nibble; SCL for 2-wire serial)
The gm5120 has an Input Format Measurement block (the IFM) providing the capability
of measuring the horizontal and vertical timing parameters of the input video source. This
information may be used to determine the video format and to detect a change in the input
format. It is also capable of detecting the field type of interlaced formats.
The IFM features a host programmable reset, separate from the regular gm5120 soft
reset. This reset disables the IFM, reducing power consumption. The IFM is capable of
operating while gm5120 is running in power down mode.
Horizontal measurements are measured in terms of the selected IFM_CLK (either
T_CLK or R_CLK/4), while vertical measurements are measured in terms of HSYNC
pulses.
The gm5120 OSD controller supports both character-mapped and bitmapped modes. A
user programmable palette of 256 true colors (255 colors, + 1 transparent) is available. In
character mapped mode, a maximum of four colors per character are available. In 8-bit
bitmapped mode, any pixel can be assigned any one of 256 user-defined true colors. In
4-bit bitmapped mode, any pixel can be assigned any one of 16 user-defined true colors (15
colors plus one transparent).
The gm5120 incorporates an embedded microprocessor, or OCM (On-Chip
Microprocessor).This processor is intended to simplify the gm5120 system software
implementation by providing embedded macro functions such as OSD menu configurations.
It is not intended to replace the system microprocessor.
An arbitration mechanism handles the register access requests from the OCM and the
system. micro.
1.4 LVDS Transmitter
IC500, 501 (SN75LVDS83) FlatLink transmitters contains four 7-bit parallel-load
serial-out shift registers, a ҏ c lock synthesizer, and five low-voltage differential-signaling
(LVDS) line drivers in a single integrated circuit. These functions allow 28 bits of
single-ended low-voltage TTL (LVTTL) data to be synchronously transmitted over five
balanced-pair conductors for receipt by a compatible receiver,
ViewSonic Corporation
45!
Confidential – Do Not Copy VX800-3
Page 40
When transmitting, data bits D0 through D27 are each loaded into registers upon the edge
of the input clock signal (CLKIN). The rising or falling edge of the clock can be selected by way
of the clock select (CLKSEL) terminal. The frequency of CLKIN is multiplied seven times ( ) and
then used to unload the data registers in 7-bit slices and serially. The four serial streams and a
phase-locked clock (CLKOUT) are then output to LVDS output drivers. The frequency of
CLKOUT is the same as the input clock, CLKIN.
The SN75LVDS83 requires no external components and little or no control. The data bus
appears the same at the input to the transmitter and output of the receiver with the data
transmission transparent to the user. The only user intervention is the possible use of the
shutdown/clear (SHTDN) active-low input to inhibit the clock and shut off the LVDS output
drivers for lower power consumption. A low-level signal on SHTDN clears all internal registers
to a low level.
ViewSonic Corporation
46!
Confidential – Do Not Copy VX800-3
Page 41
1.5 DDC 1/2 B
IC600 (24LC02) & IC602 (24LC21A) can continuously transmit its extended identification,
“EDID” using DDC1 communication channel.In addition, the monitor can respond to a request
for EDID, or complete VDIF, to be transmitted using DDC2, level B commands. Pin6 SCL is
clock input for DDC 2B, pin5 SDA for data input, and pin7 VCLK is clock input for DDC1.
In DDC1 data transfer (UNI-directional mode), the VCLK input pin is used as an input
clock for data transmission and SDA output pin is used as serial data line the SCL pin will
hold high. The DDC2B node (BI-directional mode) BUS consists of two wires. SCL is for
the data transmission clock and SDA is for the data line.
3.2 Audio Board
2.1 Audio processor
ICA2 (PT2313L) is a four-channel digital audio processor utilizing CMOS
Technology .Volume, Bass, Treble, Balance, Front/Rear Fader Processor are
incorporated into a single chip. Loudness function and Selectable input gain are also
provided to build a highly effective electronic Audio processor having the highest
performance and reliability with the least external components. And all functions are
programmable using the IIC BUS
PIN# PIN NAME I/O DESCRIPTION
1 REF - Analog reference voltage(1/2 VDD)
2 VDD - Supply input voltage
3 Agnd - Analog ground
4 Treb_L I Left channel input for treble control
5 Treb_R I Right channel input for treble control
6 RIN I Audio processor right channel input
7 Rout O Gain output&input selector for right channel
8 Loud_R I Right channel loudness input
9 Rin 3 I Right channel input 3
10 Rin 2 I Right channel input 2
11 Rin 1 I Right channel input 1
12 Loud_L I Left channel loudness input
13 Lin 3 I Light channel input 3
14 Lin 2 I Light channel input 2
15 Lin 1 I Light channel input 1
16 LIN I Audio processor left channel input
17 Lout O Gain output and input selector for left
channel
ViewSonic Corporation
47!
Confidential – Do Not Copy VX800-3
Page 42
18 Bin _L I Left bass controller input channel
19 Bout _L O Left bass controller output channel
20 Bin _R I Right bass controller input channel
21 Bout _R O Right bass controller output channel
22 RRout O Right rear speaker output
23 LRout O Left rear speaker output
24 RFout O Right front speaker output
25 LFout O Left front speaker output
26 Dgnd - Digital ground
27 Date I IIC Date
28 Clk I IIC Clk
ICA1 control & regulate the voltage (12Vto9V) to the ICA2
Volume signal through ICA2 pin24 (right) pin25 (left) into audio amplifier
ICA3
2.2 Audio amplifier:
ICA3 (TDA1517) is an integrated class-B dual output amplifier; it contains two
identical amplifier differential input stages. The gain of each amplifier is fixed at 20 dB.
Pins 1 and 9 are right and left channel inputs respectively. Pins 4 and 6 are right and
left channel outputs which connect to two 8 OHM speakers.
Pin 8 is the mute/stand-by
Pin 7 is the voltage input for ICA1
ViewSonic Corporation
48!
Confidential – Do Not Copy VX800-3
Page 43
4. Troubleshooting Flow Chart
4.1 Figure of Waveform
FIG 1. 12V FIG 2. 5V
FIG 3. 3.3V FIG 4. 2.5V
FIG 5. 32 GRAY SIGNAL INPUT FIG 6. H-SYNC
ViewSonic Corporation
49!
Confidential – Do Not Copy VX800-3
Page 44
FIG 7. V-SYNC FIG 8. 14.3M CLOCK
FIG 9. DISPLAY CLOCK FIG 10. DISPLAY H-SYNC
FIG 11. DISPLAY V-SYNC FIG 12. DISPLAY ENABLE
ViewSonic Corporation
4:!
Confidential – Do Not Copy VX800-3
Page 45
FIG 13. LVDS TX0+ FIG 14. LVDS TX0-
FIG 15.LVDS CLOCK+FIG16.LVDSCLOCK-
FIG 17. AUDIO SINE SIGNAL IN FIG 18. AUDIO SINE SIGNAL OUT
ViewSonic Corporation
51!
Confidential – Do Not Copy VX800-3
Page 46
4.2 No Display on Screen (Screen is black, LED is off)
Is screen black?
YES NO
-
Check that C202 positive is at 5V. (FIG 2.)
YES NO
Check that the voltage level of CN100 is
approximately 12V
YES NO
Check
Check CN301 pin1
IC100 failure
is12V, pin5 is 5V
YESNO
Inverter failure
Check IC400
Pin 114 failures
FB100, FB101
failure
F100 or power board failure
ViewSonic Corporation
52!
Confidential – Do Not Copy VX800-3
Page 47
4.3 No Display on Screen (LED is green)
Is the backlight lit?
YES
Check that the cable is fully
connected to CN500
Check that the cable is fully
connected between the
Inverter and Interface board
YES NO
Check IC500 ,IC501
Pin47 (FIG.13)
Pin48 (FIG.14)
Failure point
The cable is
disconnected
YES
Pin39 (FIG.15)
Pin40 (FIG.16)
NO
Check CN301 pin1 is12V,
pin5 is 5V
YES
Failure point
Check IC502
NO
NO
Failure point
The cable is disconnected
Pin 2, 4 is low
YES
Check IC502
Pin5, 6, 7, 8 is
About 5V
voltage
1. IC500, IC501 failure
2. IC400 failure
NO
IC502 failure
NO
IC502 failure
YES
Inverter failure
NO
IC400 Pin 114 failure
ViewSonic Corporation
53!
Confidential – Do Not Copy VX800-3
Page 48
4.4 No Power On
Check that CN100 Pin1 is approximately 12V
YES NO
Check that F100 output is
Failure point
12V
1. Power Board failure
2. Disconnected between CN100 and power board
YES NO
Check that FB100, FB101
Failure point
Is 12V
F100 failure
YES NO
Check that IC100
Failure point
pin 2 is about 5V
FB100, FB101 failure
NO
Failure point
1.L200 failure
2.D200 failure
3.IC100 failure
ViewSonic Corporation
54!
Confidential – Do Not Copy VX800-3
Page 49
4.5 No Sound (Test signal: 1r.m.s sine waveform)
Check that ICA3 Pin 7 is approximately 12V
YES NO
Check that ICA1 Pin 3 is
approximately 9V
YES
Check ICA2 pin11
Pin15 signal is
FIG 17.
YES
YESNO
Check ICA3 pin 4, 6
is FIG18.
NO
Check ICA1 pin2
is about 12V
Check that Q306 Pin 4 is
Low voltage
Check Q306
Pin5, 6, 7, 8 is12V
NO
Q306 failure
Failure point
1.ICA1 failure
2.IC400 pin 123 failure
NOYES
Failure point
1. JA1 failure
2. IC400 pin123 failure
YES
Check ICA5, ICA6 pin 4 is
about 5V
YES
ICA5 or ICA6 failure
ViewSonic Corporation
1. QA6 or QA7 failure
NO
2. ICA3 failure
IC400 pin 125 failure
55!
NO
Failure point
Confidential – Do Not Copy VX800-3
Page 50
4.6 Show “No Signal” on screen
(Test pattern: 32 gray 1280X1024 60HZ)
Check the signal level of R610,
R611, R612 is FIG 5.
YES
Check the HS and VS is
FIG 6. and FIG 7.
4.7 Keypad can not work
Check that the cable is
fully connected between
the Interface board and
Key board
NO
NO
Failure point
1. The video connector is disconnected
2. Signal cable is disconnected
YESNO
Failure point
1. IC400 pin 1, 4, 42, 43, 46,
47, 125,206 failure
2. TACT switch failure
ViewSonic Corporation
Failure point
The cable is disconnected
56!
Confidential – Do Not Copy VX800-3
Page 51
5. Adjust Procedure
CONTENTS
A. INSTRUMENT ALIGNMENT
PREPARATION OF MANUAL ALIGNMENT
1.
2. COLOR TEMPERATURE ALIGNMENT
3. FACTORY PRESET SETTING
ViewSonic Corporation
57
Confidential – Do Not Copy VX800-3
Page 52
5.1 Preparation of Manual Alignment
1.1 The alignment procedure is performed after unit has been completely
assembled and before set inspection.
1.2 Before Alignment, set should be burned-in for over 30min.
1.3 measuring equipment used
Pre-programmed chroma 2226 or equivalent products.
Color meter-- Minolta CA210 or equivalent products.
210 mm
CA110
1.4 methods to enter/exit factory mode
1.4.1 Press “2” and “down” key and power on to set the monitor to the burn-in mode.
1.4.2 Press “VOL-” and “1” key and power on to set the monitor to the factory mode.
1.4.3 To ensure the monitor is under factory mode, check the status in the OSD
14C-BC-0302-048733602406XXBACK CABINET
1533710055XXBRACKET VESA
1633710057XXBRACKET KENSINGTON
17322140751XTAPE
18337200500XBRACKET R/C
19310902050XSCREW TAPPING f4*1.6*10
20B-KB-0207-00315600110067K/B ASSY
21310901500XSCREW TAPPING f3*1.27*8
22M-CV-0830-2403336820520XSPEAKER COVER ASSY
23337200420XCOVER I/V
24310901140XSCREW M*0.5*6
25367019070XWIRE(PANEL TO I/F)
26B-IF-0222-00375600110055I/F BOARD
27B-AC-0215-00385600110046AUDIO BOARD
28B-SB-0221-0451490050290XDC-AC I/V
29310901010XSCREW M3*0.5*8
30310030080XSCREW M3*0.5*8
31367047370XWIRE (AUDIO TO SPK)
32M-LCD-0826-0124505180050118" TFT PANEL
33367019040XWIRE (AUDIO TO I/F)
34367019400XWIRE (I/F TO K/B)
35310901140XSCREW M3*0.5*6
36346014180XBRACKET D-SUB
37A-AD-0114-01820993026502ADAPTER
38346014190XBRACKET PANEL
39310901140XSCREW M3*0.5*6
40310901140XSCREW M3*0.5*6
41346122320XSHIELD CAN I/F
42324095740XSPONGE PU FOAM 100*1 T1
43M-CV-0830-2384336120450XCOVER BASE
44310030060XSCREW M3*0.5*6
455600200113MICROPHONE BD ASSY
46324095680XRUBBER FOOT
47337100490XBRACKET BASE
48310512450XSCREW M4*0.7*6(BLACK)
49324095750XRUBBER FOOT
50P-FM-0602-075735000848XXCUSHION T EPS
5135009324XXPE BAG
52P-FM-0602-075635000847XXCUSHION BOTTOM EPS
53P-BX-0601-0784351223490XCARTON 565*260*525 (USED ON: L18HMW 05AAW
54A-AU-0120-00333080005100CABLE AUDIO L=1800 BLK PC99
55A-MC-0105-00173080412101CABLE MICROPHONE L=1800 BLK PC99
56M-MS-0808-80333080412101D-SUB TO D-SUB RGB BLK
57M-MS-0808-80413080412401CABLE DVI-D/DVI-D SINGLE LINK
58A-PC-0106-02293090119001AC POWER CORD L1830 BLACK US
59A-PC-0106-01933070000501AC POWER CORD L1800 BLACK EURO
6035320601XXMANUAL ASSEMBLY (USED ON: L18HMW 05AAW)
ViewSonic Corporation
67!
Confidential – Do Not Copy VX800-3
Page 62
7. Schematic Diagrams
ViewSonic Corporation
Confidential – Do NotCopy VX800-3
57
Page 63
ViewSonic Corporation
Confidential – Do NotCopy VX800-3
58
Page 64
ViewSonic Corporation
Confidential – Do NotCopy VX800-3
59
Page 65
ViewSonic Corporation
Confidential – Do NotCopy VX800-3
60
Page 66
ViewSonic Corporation
Confidential – Do NotCopy VX800-3
61
Page 67
ViewSonic Corporation
Confidential – Do NotCopy VX800-3
62
Page 68
ViewSonic Corporation
Confidential – Do NotCopy VX800-3
63!
Page 69
8. PCB Layout
ViewSonic Corporation
Confidential – Do NotCopy VX800-3
64!
Page 70
ViewSonic Corporation
76!
Confidential – Do NotCopy VX800-3
Page 71
ViewSonic Corporation
Confidential – Do NotCopy VX800-3
77!
Page 72
9. Parts Lists
9.1 Recommended Spare Parts List
ItemViewSonic P/NReference No. DescriptionRemaks
1A-AD-0114-01820993026502POWER 90-264VAC 12VDC 5A COMPUTER USE
2A-PC-0106-01933070000501AC POWER CORD L1800 BLACK EURO
3A-AU-0120-00333080005100CABLE AUDIO L=1800 BLK PC99
4A-MC-0105-00173080005200CABLE MICPHONE L=1800 BLK PC99
5M-MS-0808-80333080412101CABLE D-SUB TO D-SUB RGB BLK L
6M-MS-0808-80413080412401CABLE DVI-D/DVI-D SINGLE LINK
7A-PC-0106-02293090119001AC POWER CORD L1830 BLACK US
8M-SCW-0824-04103100300600SCREW M M3*0.5*6 PAN C S+P S20PANEL BRKT+BACK CABINET
9M-SCW-0824-03913100300800SCREW M M3*0.5*8 PAN C S+P S20LCD PANEL+PANEL BKT
10M-SCW-0824-03913100300800SCREW M M3*0.5*8 PAN C S+P S20AUDIO BD+ICA3
11M-SCW-0824-06963102030800SCREW M M4*0.7*8 FLAT C S10C ZPANEL BKT+BACK CABINET
12M-SCW-0824-06903105051501SCREW M #4-40*7 HEXH #4-40*3 SCONN. D-SUB
13M-SCW-0824-06903105051501SCREW M #4-40*7 HEXH #4-40*3 SCONN. DVI-D
14M-SCW-0814-06913105120100SCREW M M4*0.7*12 PAN C S+P S1HINGE SUB ASSY+R/C
15M-SCW-0814-06923105124000SCREW M M4*0.7*6 PAN C S18C NIF/B PC/ABS
16M-SCW-0814-06923105124000SCREW M M4*0.7*6 PAN C S18C NIHINGE SUB
17M-SCW-0814-06933105124500SCREW M M4*0.7*6 FF C S18C ZNNECK SUB ASSY+BASE COVER
18M-SCW-0814-06933105124500SCREW M M4*0.7*6 FF C S18C ZNNECK BRKT+BKT BUTTON
19M-SCW-0824-04133109011400SCREW T M3*0.5*6 BIND C S18C ZI/V+PANEL BKT
20M-SCW-0824-04133109011400SCREW T M3*0.5*6 BIND C S18C ZAUDIO BD+PANELBKT
21M-SCW-0824-04133109011400SCREW T M3*0.5*6 BIND C S18C ZD-SUB BKT+SHEILD CAN
22M-SCW-0824-04133109011400SCREW T M3*0.5*6 BIND C S18C ZD-SUB BKT+PANEL BKT
23M-SCW-0824-04133109011400SCREW T M3*0.5*6 BIND C S18C ZPOWER BD+PANEL BKT
24M-SCW-0824-04133109011400SCREW T M3*0.5*6 BIND C S18C ZI/F+PANEL BKT
25M-SCW-0824-04133109011400SCREW T M3*0.5*6 BIND C S18C ZI/V SHIELD CAN+PANEL BKT
26M-SCW-0824-04133109011400SCREW T M3*0.5*6 BIND C S18C ZI/V SHIELD CAN +PANEL BKT
27M-SCW-0814-06943109015000SCREW T ij3*1.27*8 PAN C S20CK/B+SPK COVER
28M-SCW-0824-06203109020500SCREW T ij4*1.6*10 PAN C S18CBACK CABINET+PANEL BRKT
29M-SCW-0824-06203109020500SCREW T ij4*1.6*10 PAN C S18CBACK CABINET
30M-SCW-0824-04313109020800SCREW T ij4*1.6*12 PAN C S18CAC SOCKET GND
31M-SCW-0824-07333109026000SCREW T ij4*1.27*12 FPH C S18CSPEAKER &BACK CABINET
32M-SCW-0824-07333109026000SCREW T ij4*1.27*12 FPH C S18CNECK F/C P
33M-MS-0808-80403110250000WASHER SPRING SWRTCONN D-SUB
34M-MS-0808-80403110250000WASHER SPRING SWRTCONN DVI-D
35M-MS-0808-46863200462800NAME PLATE AL+PC VSC 3-BIRD LO
36M-MS-0808-81513200641801NAME PLATE AL 43*6.9*1.15T VIE
37M-MS-0808-77393200648800NAME PLATE ABS 94HB VIEWSONIC
38M-LB-0813-07633201942500LABEL ID 160*43 VSC VX800-3
39M-LB-0813-07003202207300LABEL MIC IN 10.2*15
40M-LB-0813-07143202310700LABEL HV WARNING 100*25
41M-MS-0808-83033211024500MYLAR 435*350 T.2FRONT BEZEL
42C-BC-0302-04773360240100R/C ABS VSC02B VX700-2
43C-BC-0302-04873360240600CABINET BACK ABS 41 VX800-2
44PL-FK-0709-01143360727100FUNCTION KEY ABS VSC02B S7LFA1
45M-CV-0830-23813360916300ARM FRONT ABS 41 VX700-2
46M-CV-0830-23823360916400ARM REAR ABS 41 VX700-2
47C-FP-0301-03263361074400F/B ABS SV-651 VX800-2
48M-CV-0830-23843361204500COVER BASE ABS 41 VX700-2
49M-CV-0830-24023361204800COVER SPEAKER ABS 41 VX800-2
50M-CV-0830-24033368205200SPEAKER COVER ASSY L18HMW05AAW
51C-BC-0302-04793368213600R/C ASSY L17KMW05AAW
52M-MS-0808-81593371004902BRKT BASE SPCC T=2 ZN BLK
53M-MS-0808-81603371005202BRACKET MECK SPCC T=2 ZN BLUE
54M-MH-0822-00023371005500BRACKET VESA MOUNTING SECC T=1FOR CABINET BACK
55M-MH-0822-00043371005701BRACKET KENSINGTON SECC T=1.2FOR CABINET BACK
56M-CV-0830-23483372004201COVER INVERT SECC T=0.6 18"
57M-MS-0808-82233372005001BRACKET R/C SUB SECC T=1.2R/C PC/ABS
58M-MS-0808-81623421024500CABLE CLAMP GROUNDING SPCC T.3K/B WIRE+PANEL BRKT
59M-CV-0830-23693460119101BRACKET REAR COVER SECC T=1.2
60M-MH-0822-00383460141801BRACKET D-SUB SECC 211.5*23.8
61M-MH-0822-00103460141900BRACKET PANEL SECC 408*326.2 T
ViewSonic Corporation
78!
Confidential – Do Not Copy VX800-3
Page 73
62M-CV-0830-23963461223200SHIELD CAN I/F SPTH 219.5*141.
63M-MS-0808-81633461750601HINGE SUB ASSY R
64M-MS-0808-81643461750701HINGE SUB ASSY L
65M-MS-0808-81653463000400CONDUCTIVE AL 50*30 T=0.1LCD COVER
66P-FM-0602-07563500084701END BLOCK EPS (B) 558*261*170
67P-FM-0602-07573500084801END BLOCK EPS (T) 558*261*170
68M-MS-0808-76743500932401PE BAG 500*640 T=0.06 CLEAN
69P-BX-0601-07843512234900CARTON 565*265*595 VSC VG800-2
70M-MS-0808-83963520094201PE BAG 260*155*0.1TFOR MANUAL
71M-MS-0808-77503532060100MANUAL PACKING ASSY VSC VX80072A-CD-VX800-33532060200CD-ROM VSC A-CD-VX800-3
73M-WR-0828-06883610170900AC SOCKET ASSY L19EMW05AAW L20
74M-WR-0828-06823670190400WIRE WITH HOUSING 1007 #28 L12AUDIO TO I/F
75M-WR-0828-06893670190700WIRE WITH HOUSING 20276 #30 L2PANEL TO I/F
76M-WR-0828-06903670194000WIRE WITH HOUSING 20276 #28 L3K/B TO I/F
77M-WR-0828-06413670459102WIRE WITH HOUSING 1007 #28 L=4AUDIO/BD JA2
78E-SK-0412-00703790193400SPEAKER-R ASSY L17KMW05AAW
79E-SK-0412-00713790193500SPEAKER-L ASSY L17KMW05AAW
80B-SB-0221-04514900502900DC-AC INVERTER 12V/1500VMIN 6L
81M-MS-0808-77515011086700MANUAL QUICK START GUIDE VSC V
82M-LCD-0826-01245051800501LCD 18.0" TFT PANEL
83B-AC-0215-00385600110046LCD AUDIO BD ASSY L19EMW 05AAW
84B-IF-0222-00375600110055LCD I/F BD ASSY L18HMW 05AAW
85B-KB-0207-00315600110067LCD FUN KEY BD ASSY L19EMW 05A
POWER 90-264VAC 12VDC 5A
AC POWER CORD L1800 BLACK
CABLE AUDIO L=1800 BLK PC99
CABLE MICPHONE L=1800 BLK
CABLE D-SUB TO D-SUB RGB BLK L
CABLE DVI-D/DVI-D SINGLE LINK
AC POWER CORD L1830 BLACK US
SCREW M M3*0.5*6 PAN C S+P S20
SCREW M M3*0.5*8 PAN C S+P S20
SCREW M M3*0.5*8 PAN C S+P S20
SCREW M M4*0.7*8 FLAT C S10C Z
SCREW M #4-40*7 HEXH #4-40*3 S
SCREW M #4-40*7 HEXH #4-40*3 S
SCREW M M4*0.7*12 PAN C S+P S1
SCREW M M4*0.7*6 PAN C S18C NI
SCREW M M4*0.7*6 PAN C S18C NI
SCREW M M4*0.7*6 FF C S18C ZN
SCREW M M4*0.7*6 FF C S18C ZN
SCREW T M3*0.5*6 BIND C S18C Z
SCREW T M3*0.5*6 BIND C S18C Z
SCREW T M3*0.5*6 BIND C S18C Z
SCREW T M3*0.5*6 BIND C S18C Z
SCREW T M3*0.5*6 BIND C S18C Z
SCREW T M3*0.5*6 BIND C S18C Z
SCREW T M3*0.5*6 BIND C S18C Z
SCREW T M3*0.5*6 BIND C S18C Z
SCREW T ij3*1.27*8 PAN C S20C
SCREW T ij4*1.6*10 PAN C S18C
SCREW T ij4*1.6*10 PAN C S18C
SCREW T ij4*1.6*12 PAN C S18C
SCREW T ij4*1.27*12 FPH C S18C
SCREW T ij4*1.27*12 FPH C S18C
WASHER SPRING SWRT
WASHER SPRING SWRT
LABEL WARING
NAME PLATE AL+PC VSC 3-BIRD LO
NAME PLATE AL 43*6.9*1.15T VIE
LABEL CONTROL 100*90
LABEL BAR CODE 55*15 VSC-G
LABEL BAR CODE 76*121
LABEL VER. CONTROL 20*20 VIEWS
LABEL ID 160*43 VSC VX800-3
LABEL MIC IN 10.2*15
LABEL HV WARNING 100*25
MYLAR 435*350 T.2
TAPE W=10 #1350F-1 3M
TAPE W=45 #7290 NITTO
TAPE W=76 PP47 50M 4P
TAPE W=7 VHB4926 E468
INSULATOR FR-700 T.4 193.2*40
RUBBER FOOT 81*13*3T BLK
RUBBER FOOT 75*10 T3
RUBBER HOLD PLUG OD5.2 H3.8 BL
HSK AL T=1.5 21*9
CABINET BACK ABS 41 VX800-2
PLASTIC ABS 94HB 41 D-180
PLASTIC ABS 94HB 41 SD-0150
PLASTIC ABS 94HB 41 PA-707
PE FILM t=0.02mm W=500
PE SHEET 1800*1600*0.15
PE SHIELDING BAG 280*200
DRYER 15G 80*60
PLASTIC STRIP W=12 T.5 BLACK
MANUAL PACKING ASSY VSC
PE BAG 260*155*0.1T
MANUAL QUICK START GUIDE VSC
CD-ROM VSC A-CD-VX800-3
AC SOCKET ASSY L19EMW05AAW
WIRE WITH HOUSING 1007 #28 L12
WIRE WITH HOUSING 20276 #30 L2
WIRE WITH HOUSING 20276 #28 L3
WIRE WITH HOUSING 2547 #28 L47
SPEAKER-R ASSY L17KMW05AAW
SPEAKER-L ASSY L17KMW05AAW
DC-AC INVERTER 12V/1500VMIN 6L
LCD 18.0" TFT PANEL
LCD AUDIO BD ASSY L19EMW
RES CH 1/10W 1K F 0603
RES CH 1/8W 2.4K F 0805
RES CH 1/10W ZERO J 0603
RES CH 1/10W ZERO J 0603
RES CH 1/10W 1K J 0603
RES CH 1/10W 1K J 0603
RES CH 1/10W 10K J 0603
RES CH 1/10W 10K J 0603
RES CH 1/10W 10K J 0603
RES CH 1/10W 10K J 0603
RES CH 1/10W 22 J 0603
RES CH 1/10W 22 J 0603
RES CH 1/10W 220 J 0603
RES CH 1/10W 220 J 0603
RES CH 1/10W 2.2K J 0603
RES CH 1/10W 2.2K J 0603
RES CH 1/10W 4.7K J 0603
RES CH 1/10W 4.7K J 0603
RES CH 1/10W 47K J 0603
RES CH 1/10W 47K J 0603
RES CH 1/10W 5.6K J 0603
RES CH 1/10W 5.6K J 0603
CAP AL CP 16V 47U M 6.3*5.4
CAP AL CP 16V 47U M 6.3*5.4
CAP AL CP 16V 47U M 6.3*5.4
CAP AL CP 16V 47U M 6.3*5.4
CAP AL CP 16V 47U M 6.3*5.4
CAP AL CP 16V 47U M 6.3*5.4
CAP AL CP 25V 4.7U M 4*5.5
CAP AL CP 25V 4.7U M 4*5.5
CAP AL CP 25V 4.7U M 4*5.5
CAP AL CP 25V 4.7U M 4*5.5
CAP AL CP 16V 470U M 8*10
CAP AL CP 16V 470U M 8*10
CAP AL CP 25V 10U M 5*5.7
CAP AL CP 25V 10U M 5*5.7
CAP AL CP 25V 10U M 5*5.7
CAP AL CP 25V 10U M 5*5.7
CAP AL CP 25V 10U M 5*5.7
CAP AL CP 25V 10U M 5*5.7
CAP MC CP 50V 2.7KP J X7R 0603
CAP MC CP 50V 2.7KP J X7R 0603
CAP MC CP 50V 100P J C0G 0603
CAP MC CP 50V 100P J C0G 0603
CAP MC CP 50V 100P J C0G 0603
CAP MC CP 50V 100P J C0G 0603
CAP MC CP 50V 1KP J C0G 0603
CAP MC CP 50V 1KP J C0G 0603
CAP MC CP 50V .1U Z Y5V 0603
CAP MC CP 50V .1U Z Y5V 0603
CAP MC CP 50V .1U Z Y5V 0603
CAP MC CP 50V .1U Z Y5V 0603
CAP MC CP 50V .1U Z Y5V 0603
CAP MC CP 50V .1U Z Y5V 0603
CAP MC CP 50V .1U Z Y5V 0603
CAP MC CP 50V .1U Z Y5V 0603
CAP MC CP 50V .1U Z Y5V 0603
CAP MC CP 50V .1U Z Y5V 0603
CAP MC CP 50V .1U Z Y5V 0603
DIO ZEN 0.5W 5.45-5.73V LLDS(M
DIO ZEN 0.5W 6.66-7.01V LLDS(M
DIO ZEN 0.5W 6.66-7.01V LLDS(M
DIO ZEN 0.5W 6.66-7.01V LLDS(M
DIO ZEN 0.5W 6.66-7.01V LLDS(M
DIO SW 0.15A 75V MINIMELF
TR 40V 0.2A SOT-23 100-300
TR 40V 0.2A SOT-23 100-300
TR 40V 1A SOT-23 75
FET 30V 7A 28mohm SO-8PIN
FET 30V 7A 28mohm SO-8PIN
FET 30V 7A 0.028ohm SO-8
FET 30V 7A 0.028ohm SO-8
IC REGU +20V 1A SC-63 5PIN
IC 4-CH AUDIO PROCESSOR SOIC 2*6 STEREO CARD RADIO 9P
CORE BEAD 100MHZ 40 OHM 0.4A 0
CORE BEAD 100MHZ 40 OHM 0.4A 0
CORE BEAD 100MHZ 80 OHM 3A
CORE BEAD 100MHZ 80 OHM 3A
PWB D0 L2 FR-4 60*100 (AUDIO B
HEADER NYLON66 94V-0 4P P2.5
CONN PHONE JACK OD3.5 7P
CONN PHONE JACK OD3.5 7P R/A G
HEADER BOX PBT 94V0 2*5P P2.0
LCD I/F BD ASSY L18HMW 05AAW
RES CH 1/4W 150 J 1206
RES CH 1/4W 150 J 1206
RES CH 1/10W ZERO J 0603
RES CH 1/10W ZERO J 0603
RES CH 1/10W ZERO J 0603
RES CH 1/10W ZERO J 0603
RES CH 1/10W ZERO J 0603
RES CH 1/10W ZERO J 0603
RES CH 1/10W ZERO J 0603
RES CH 1/10W ZERO J 0603
RES CH 1/10W ZERO J 0603
RES CH 1/10W 100 J 0603
RES CH 1/10W 100 J 0603
RES CH 1/10W 100 J 0603
RES CH 1/10W 100 J 0603
RES CH 1/10W 100 J 0603
RES CH 1/10W 470 J 0603
RES CH 1/10W 470 J 0603
RES CH 1/10W 470 J 0603
RES CH 1/10W 470 J 0603
RES CH 1/10W 470 J 0603
RES CH 1/10W 470 J 0603
RES CH 1/10W 470 J 0603
RES CH 1/10W 470 J 0603
RES CH 1/10W 470 J 0603
RES CH 1/10W 470 J 0603
RES CH 1/10W 4.7K J 0603
RES CH 1/10W 4.7K J 0603
RES CH 1/10W 4.7K J 0603
RES CH 1/10W 4.7K J 0603
RES CH 1/10W 4.7K J 0603
RES CH 1/10W 4.7K J 0603
RES CH 1/10W 4.7K J 0603
RES CH 1/10W 4.7K J 0603
RES CH 1/10W 4.7K J 0603
RES CH 1/10W 4.7K J 0603
RES CH 1/10W 4.7K J 0603
RES CH 1/10W 6.8M J 0603
RES CH 1/10W 75 J 0603
RES CH 1/10W 75 J 0603
RES CH 1/10W 75 J 0603
RES CH 1/10W 82K J 0603
RES ARRAY 1/16W 22 J 16P8R 4*1
RES ARRAY 1/16W 22 J 16P8R 4*1
RES ARRAY 1/16W 22 J 16P8R 4*1
RES ARRAY 1/16W 22 J 16P8R 4*1
RES ARRAY 1/16W 22 J 16P8R 4*1
RES ARRAY 1/16W 22 J 16P8R 4*1
RES ARRAY 10K J 8P4R 1206
RES ARRAY 10K J 8P4R 1206
RES ARRAY 10K J 8P4R 1206
RES ARRAY 10K J 8P4R 1206
CRYSTAL 14.318MHZ+-30PPM ATFUSE F/P 4A 125V UL CSA
CAP AL CP 16V 100U M 6.3*5.4
CAP AL CP 16V 100U M 6.3*5.4
CAP AL CP 16V 100U M 6.3*5.4
CAP AL CP 16V 100U M 6.3*5.4
CAP AL CP 16V 100U M 6.3*5.4
CAP AL CP 16V 100U M 6.3*5.4
CAP AL CP 16V 100U M 6.3*5.4
CAP AL CP 16V 100U M 6.3*5.5
CAP AL CP 16V 100U M 6.3*5.5
CAP AL CP 16V 100U M 6.3*5.5
CAP AL CP 16V 100U M 6.3*5.5
CAP AL CP 16V 100U M 6.3*5.5
CAP AL CP 16V 100U M 6.3*5.5
CAP AL CP 16V 100U M 6.3*5.5
CAP AL CP 16V 47U M 6.3*5.4
CAP AL CP 16V 47U M 6.3*5.4
CAP AL CP 16V 47U M 6.3*5.4
CAP AL CP 16V 47U M 6.3*5.5
CAP AL CP 16V 47U M 6.3*5.5
CAP AL CP 16V 47U M 6.3*5.5
CAP AL CP 16V 10U M 4*5.5
CAP AL CP 16V 10U M 4*5.4
.AP AL CP 16V 220U M 6.3*7.7
.AP AL CP 16V 220U M 6.3*7.7
CAP AL CP 16V 470U M 8*10.5
CAP AL CP 16V 470U M 8*10.5
CAP AL CP 16V 470U M 8*10
CAP AL CP 16V 470U M 8*10
CAP AL CP 25V 220U M 8*10.5
CAP AL CP 25V 220U M 8*10.5
CAP AL CP 25V 220U M 8*10
CAP AL CP 25V 220U M 8*10
CAP MC CP 50V .01U J X7R 0603
CAP MC CP 50V .01U J X7R 0603
CAP MC CP 50V .01U J X7R 0603
CAP MC CP 50V .01U J X7R 0603
CAP MC CP 50V .01U J X7R 0603
CAP MC CP 50V .01U J X7R 0603
CAP MC CP 50V .01U J X7R 0603
CAP MC CP 50V .01U J X7R 0603
CAP MC CP 50V .01U J X7R 0603
CAP MC CP 50V .01U J X7R 0603
CAP MC CP 50V .01U J X7R 0603
CAP MC CP 50V .01U J X7R 0603
CAP MC CP 50V .01U J X7R 0603
CAP MC CP 50V .01U J X7R 0603
CAP MC CP 50V .01U J X7R 0603
CAP MC CP 50V .01U J X7R 0603
CAP MC CP 50V .01U J X7R 0603
CAP MC CP 50V .01U J X7R 0603
CAP MC CP 50V .01U J X7R 0603
CAP MC CP 50V .01U J X7R 0603
CAP MC CP 50V .01U J X7R 0603
CAP MC CP 50V .01U J X7R 0603
CAP MC CP 50V .01U J X7R 0603
CAP MC CP 50V 22P J C0G 0603
CAP MC CP 50V 22P J C0G 0603
CAP MC CP 50V 22P J C0G 0603
CAP MC CP 50V 22P J C0G 0603
CAP MC CP 50V 22P J C0G 0603
CAP MC CP 50V 22P J C0G 0603
CAP MC CP 50V 5P C C0G 0603
CAP MC CP 50V 5P C C0G 0603
CAP MC CP 16V 1U Z Y5V 0805
CAP MC CP 16V 1U Z Y5V 0805
CAP MC CP 16V 1U Z Y5V 0805
CAP MC CP 16V 1U Z Y5V 0805
CAP MC CP 16V 1U Z Y5V 0805
CAP MC CP 16V 1U Z Y5V 0805
CAP MC CP 16V 1U Z Y5V 0805
CAP MC CP 16V 1U Z Y5V 0805
CAP MC CP 16V 1U Z Y5V 0805
CAP MC CP 25V .1U K X7R 0603
CAP MC CP 25V .1U K X7R 0603
CAP MC CP 25V .1U K X7R 0603
CAP MC CP 25V .1U K X7R 0603
CAP MC CP 25V .1U K X7R 0603
CAP MC CP 25V .1U K X7R 0603
CAP MC CP 25V .1U K X7R 0603
CAP MC CP 25V .1U K X7R 0603
CAP MC CP 25V .1U K X7R 0603
CAP MC CP 25V .1U K X7R 0603
CAP MC CP 25V .1U K X7R 0603
CAP MC CP 25V .1U K X7R 0603
CAP MC CP 25V .1U K X7R 0603
CAP MC CP 25V .1U K X7R 0603
CAP MC CP 25V .1U K X7R 0603
CAP MC CP 25V .1U K X7R 0603
CAP MC CP 25V .1U K X7R 0603
CAP MC CP 25V .1U K X7R 0603
CAP MC CP 25V .1U K X7R 0603
CAP MC CP 25V .1U K X7R 0603
CAP MC CP 25V .1U K X7R 0603
CAP MC CP 25V .1U K X7R 0603
CAP MC CP 25V .1U K X7R 0603
CAP MC CP 25V .1U K X7R 0603
CAP MC CP 25V .1U K X7R 0603
CAP MC CP 25V .1U K X7R 0603
CAP MC CP 25V .1U K X7R 0603
CAP MC CP 25V .1U K X7R 0603
CAP MC CP 25V .1U K X7R 0603
CAP MC CP 25V .1U K X7R 0603
CAP MC CP 25V .1U K X7R 0603
CAP MC CP 25V .1U K X7R 0603
CAP MC CP 25V .1U K X7R 0603
CAP MC CP 25V .1U K X7R 0603
CAP MC CP 25V .1U K X7R 0603
CAP MC CP 25V .1U K X7R 0603
CAP MC CP 25V .1U K X7R 0603
CAP MC CP 25V .1U K X7R 0603
CAP MC CP 25V .1U K X7R 0603
CAP MC CP 25V .1U K X7R 0603
CAP MC CP 25V .1U K X7R 0603
CAP MC CP 25V .1U K X7R 0603
CAP MC CP 25V .1U K X7R 0603
CAP MC CP 25V .1U K X7R 0603
CAP MC CP 25V .1U K X7R 0603
CAP MC CP 25V .1U K X7R 0603
CAP MC CP 25V .1U K X7R 0603
CAP MC CP 25V .1U K X7R 0603
CAP MC CP 25V .1U K X7R 0603
CAP MC CP 25V .1U K X7R 0603
CAP MC CP 25V .1U K X7R 0603
CAP MC CP 25V .1U K X7R 0603
CAP MC CP 25V .1U K X7R 0603
DIO SBD 3A 40V DO-201AD
DIO ZEN 0.5W 5.45-5.73V LLDS(M
DIO ZEN 0.5W 5.45-5.73V LLDS(M
DIO ZEN 0.5W 5.45-5.73V LLDS(M
DIO ZEN 0.5W 5.45-5.73V LLDS(M
DIO ZEN 0.5W 5.45-5.73V LLDS(M
DIO ZEN 0.5W 5.45-5.73V LLDS(M
DIO SW 0.215A 70V SOT-23 SE.
DIO SW 0.215A 70V SOT-23 SE.
DIO SW 0.215A 70V SOT-23 SE.
DIO SW 0.215A 70V SOT-23 SE.
DIO SW 0.215A 70V SOT-23 SE.
DIO SW 0.215A 70V SOT-23 SE.
DIO SW 0.215A 70V SOT-23 SE.
DIO SW 0.215A 75V SOT-23 SE.
DIO SW 0.215A 75V SOT-23 SE.
DIO SW 0.215A 75V SOT-23 SE.