ViewSonic VG730m-3 VS11383, VA730m-1 VS11383 Service Manual

ViewSonic VG730m-3

VA730m-1

Model No. VS11383

17” Color TFT LCD Display

(VG730m-3_VA730m-1_SM Rev. 1a Oct. 2006)

ViewSonic 381 Brea Canyon Road, Walnut, California 91789 USA - [phone]

Service Manual

ViewSonic Corporation Confidential - Do Not Copy VG730m-3_VA730m-1

i

Copyright

Copyright © 2006 by ViewSonic Corporation. All rights reserved. No part of this publication
may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any
language or computer language, in any form or by any means, electronic, mechanical, magnetic,
optical, chemical, manual or otherwise, without the prior written permission of ViewSonic
Corporation.

Disclaimer

ViewSonic makes no representations or warranties, either expressed or implied, with respect to
the contents hereof and specifically disclaims any warranty of merchantability or fitness for any
particular purpose. Further, ViewSonic reserves the right to revise this publication and to make
changes from time to time in the contents hereof without obligation of ViewSonic to notify any
person of such revision or changes.

Trademarks

Optiquest is a registered trademark of ViewSonic Corporation.
ViewSonic is a registered trademark of ViewSonic Corporation.
All other trademarks used within this document are the property of their respective owners.

Revision History

Revision SM Editing Date ECR Number Description of Changes Editor

1a 10/17/2006 Initial Release Jamie Chang

ViewSonic Corporation Confidential - Do Not Copy

ii

TABLE OF CONTENTS

1. Precautions and Safety Notices 1

2. Specification 3

3. Front Panel Function Control Description 7

4. Circuit Description 13

5. Adjustment Procedure 20

6. Troubleshooting Flow Chart 55

7. Recommended Spare Parts List 63

8. Exploded Diagram and Exploded Parts List 68

9. Block Diagram 71

10. Schematic Diagrams 72

11. PCB Layout Diagrams 78

VG730m-3_VA730m-1

ViewSonic Corporation Confidential - Do Not Copy

1

1. Precautions and Safety Notices

1. Please carefully read this manual before operating the device and keep it available for future reference.

2. T o avoid the danger of the m onitor falling and th ereby possibly causing injury and/or serious damage to the monitor
itself, do not place it on unstable cars or desks. Be careful to avoid placing any stress on the LCD screen during
handling.

3. Do not place this monitor in areas that are wet or where water or other liquids may come in contact with it, such as
bathrooms, kitchens, wet floors, near washing machines or by swimming pools.

4. Remove the power plug from the electrical socket before cleaning. No water-containing cleaning agent should be
used to clean the screen, but only cleaning agents formulated specifically for cleaning LCD screens. Do not put any
liquid cleaning agent directly on the screen, but put it on a soft cloth first and then gently apply the cloth to the screen.

5. In order to guarantee reliable operation and adequate heat dissi pation, do not cover or block vent hole s on the monitor .
Do not put the monitor close to heat sources. Do not place the monitor on furniture such as a bookshelf, unless
sufficient ventilation is available.

6. A 3-pin grounding plug is provided for this monitor. In order to guarantee normal operation and safety of this unit,
this plug should be used with a matching grounded power socket.

7. Please follow all warnings and instructions that accompany the monitor.

8. Please pay special attention to power supply overloads, as electrical shock or fire may occur.

9. Do not place anything on the power cord. Do not hang the power cord over an area where people or objects may pass.

10. In case the monitor is not be used for an extended period, turn off power to avoid the possibility of short circuits
caused by lightning.

11. In order to avoid electrical shock or fire risks, do not insert any object through any openings in the monitor’s
enclosure. Do not allow any liquid to come in contact with the monitor.

12. In case of any abnormal noise or odor caused by incorrect operation, turn off power immediately and contact a
professional technician. Do not attempt to repair this monitor by yourself, as electrical shock may occur when
opening the back cover or accessing internal components.

13. If any of the following conditions occurs, turn off power and contact a repair service provider:

1) the power cord is damaged or worn;

2) liquid has gotten into the monitor, or the monitor has experienced immersion or wetting;

3) the monitor has fallen;

4) the monitor’s performance shows obvious changes;

5) the monitor fails to work normally when correct procedures are followed. In that case, please make any

adjustments in accordance with instructions supplied with the monitor; do not attempt any changes to
established procedures, as further damage may occur, making successful repair of the monitor more difficult.

14. In case parts need to be replaced, you must use identical parts or those supplied by our certified

manufacturers. Any other parts used without our authorization may result in electrical shock or
fire risk.

VG730m-3_VA730m-1

Handing and Placing methods

Correct methods Incorrect methods

Only touch the metal frame of the LCD panel or the front

cover of the monitor, DO not touch the surface of the

POL

Surface of the LCD panel is pressed by fingers and that

may cause”mura”

ViewSonic Corporation Confidential - Do Not Copy

2

VG730m-3_VA730m-1

ViewSonic Corporation Confidential - Do Not Copy

3

2. Specification

VA730m-1

1. 1st LCD PANEL

Maker
Resolution
Size / AA size
Pixel Arrange
surface Treatment

Brightness
Contrast Ratio
Viewing Angle

Colors
Response Time
Backlight
Backlight Life

CR>10
CR>5

Innolux MT170EN01

1280*1024 (SXGA)

337.9 mm x 270.3mm (17” TFT)
RGB Vertical Stripe, 0.264mm pixel pitch.
Anti-Glare, Hard Coating

280 cd/m2 (typ), 250 cd/m2 (min)
600:1(typ), 500: 1 (min)
H/V= 150/130 ( typ), 135/115(min)
H/V= 170/155 ( typ), 155/135 (min)

16.2 M colors (6 bit with FRC)
8ms (typ), 16ms(max)
N=4 CCFLs (Cold Cathode Florescent Tube)
50,000 hours (min)

2. 2nd LCD PANEL

Maker
Resolution
Size / AA size
Pixel Arrange
surface Treatment

Brightness
Contrast Ratio
Viewing Angle

Colors
Response Time
Backlight
Backlight Life

CR>10
CR>5

SVA 170SX01 TB
1280*1024 (SXGA)

337.9 mm x 270.3mm (17” TFT)
RGB Vertical Stripe, 0.264mm pixel pitch.
Anti-Glare, Hard Coating

300 cd/m2 (typ), 240 cd/m2 (min)
600:1(typ), 400: 1 (min)
H/V= 130/110 ( typ), 115/80(min)
H/V= N/A / N/A ( typ), N/A / N/A (min)

16.2 M colors (6 bit with FRC)
8ms (typ), 20ms(max)
N=4 CCFLs (Cold Cathode Florescent Tube)
50,000 hours (Typ)

3. INPUT SIGNAL

Video

Sync

RGB Analog (75 ohms, 0.7 / 1.0 Vp-p)

H/V Separated (TTL)
FH:30 – 82 kHz, fV:56-75Hz

4. COMPATIBILITY

PC
Mac*

PC Compatibles ( VGA 1280*1024 Non Interlaced)

Power Mac (1280*1024)

5. RESOLUTION

Recommended

Supported

1280*1024 @ 60Hz

640 x 350 ,640 x 400, 640 x 480 ,720 x 400
800 x 600 , 832 x 624,1280*1024

6. CONNECTORS

Signal
Power
audio

15 pin mini D-sub,

3 pin AC plug In
Stereo min audio line in

7. POWER

Voltage
Consumption

Integrated AC 100-240V (Universal)

40W (max)

8. AUDIO

Amplifier
speaker

1.5W

1.5W x 2

9. ERGONOMICS

Tilt

Forward
Back

Base

5 Degrees
20 Degrees for normal use,

80mm height adjustment
360 degree swivel

10. CONTROLS

Physical

OSD Function

Main Menu

Power , [;X] [1], [▼], [▲], [2]

Auto Image Adjust, Contrast/Brightness, Input Select
Audio, Color adjust, Information, Manual Image Adjust,
Setup Menu , Memory Recall

11. BANDWIDTH 135 MHz (MAX)

12.

OPERATING

CONDITION

Temperature
Humidity

41°F to 95°F (5°C to 35°C)

20% to 80% (no condensation)

13.

STORAGE /

SHIPPING

CONDITION

Temperature
Humidity

-4°F to 131 °F (-20°C to 55°C)°
20% to 85% (no condensation)

VG730m-3_VA730m-1

ViewSonic Corporation Confidential - Do Not Copy

4

Physical(W*H*D)

With stand

VESA
mount

388 x 450x 230 ( mm ), 15.2 x 18.6 x 9.0 (in)

100x100mm

14. DIMENSIONS

Packaging(W*H*D) 445 x 552 x 278 (mm ) 17.5. x 21.7x 10.9(in)
Net 4.9 kg , 10.8 lbs

15. WEIGHT

Gross 6.0 kg , 13.2 lbs (including carton, EPS & cables)

16. REGULATIONS

CB / TCO03/ UL/cUL / FCC-B / EPA Energy Star /

TUV/Ergo / ISO13406-2 / TUV-S / CE / BSMI / PSB /
C-Tick / MIC/CCC

17.

POWER SAVING

FUNCTION

"On"
" Active Off"

BLUE
AMBER

40W (max) , 35(typ)
<1 W (typ)

18.

LOGISTICS

Container Load
Pallet Load
UPC Code (UPC-A)
PC Code(ITF-14)
Serial Format

40’/20’
sea

728 / 336 units
28 pcs per pallet
7 66907 23195 3
0 07 66907 23195 3
QD4YYWWKxxxx

19. SECURITY Kensington Lock on the bottom right side

20.

EU Packaging

Information

1. Weight of the individual (empty) shipping carton.---------------0.65 kg

2. Weight and materials of the poly foam.----------------------------90g/set,EPS

3. Weight and material of the empty accessory plastic bags ------20g/PE-LD

4. Weight and material of the plastic handle.------------------------12 g/PE-LD

5. Weight and material of the pallets ... 16Kg, popar ;
…16Kg., Fumigation wood,

21. ACCESSORIES

Power cable
analog D-sub video cable
audio cable
Quick Start Guide and CD-wizard

Support Timings

Item Timing Analog Digital

1 640 x 350 @ 70Hz, 31.5kHz Yes Yes
2 640 x 400 @ 60Hz, 31.5kHz Yes Yes
3 640 x 400 @ 70Hz, 31.5kHz Yes Yes
4 640 x 480 @ 50Hz, 24.7kHz Yes No
5 640 x 480 @ 60Hz, 31.5kHz Yes Yes
6 640 x 480 @ 67Hz, 35.0kHz Yes Yes
7 640 x 480 @ 72Hz, 37.9kHz Yes Yes
8 640 x 480 @ 75Hz, 37.5kHz Yes Yes
9 640 x 480 @ 85Hz, 43.27kHz No No

10 720 x 400 @ 70Hz, 31.5kHz Yes Yes

11 800 x 600 @ 56Hz, 35.1kHz Yes Yes
12 800 x 600 @ 60Hz, 37.9kHz Yes Yes
13 800 x 600 @ 75Hz, 46.9kHz Yes Yes
14 800 x 600 @ 72Hz, 48.1kHz Yes Yes
15 800 x 600 @ 85Hz, 53.7kHz No No
16 832 x 624 @ 75Hz, 49.7kHz Yes Yes
17 1024 x 768 @ 60Hz, 48.4kHz Yes Yes
18 1024 x 768 @ 70Hz, 56.5kHz Yes Yes
19 1024 x 768 @ 72Hz, 58.1kHz Yes Yes
20 1024 x 768 @ 75Hz, 60.0kHz Yes Yes
21 1024 x 768 @ 85Hz, 68.67kHz No No
22 1152 x 864 @ 75Hz, 67.5kHz Yes Yes
23 1152 x 870 @ 75Hz, 68.7kHz Yes Yes
24 1280 x 1024 @ 60Hz, 63.4kHz Yes Yes
25 1280 x 1024 @ 75Hz, 79.97kHz Yes Yes
26 1280x 720 @ 60Hz, 45kHz (HDTV) Yes Yes

VG730m-3_VA730m-1

ViewSonic Corporation Confidential - Do Not Copy

5

VG730m-3

1. LCD PANEL

Maker
Resolution
Size / AA size
Pixel Arrange
surface Treatment

Brightness
Contrast Ratio
Viewing Angle

Colors
Response Time
Backlight
Backlight Life

CR>10
CR>5

Innolux

1280*1024 (SXGA)

337.9 mm x 270.3mm (17” TFT)
RGB Vertical Stripe, 0.264mm pixel pitch.
Anti-Glare, Hard Coating

280 cd/m2 (typ), 250 cd/m2 (min)
600:1(typ), 500: 1 (min)`
H/V= 150/145 ( typ), 130/115(min)
H/V= 170/155 ( typ), 150/135 (min)

16.2 M colors (6 bit with FRC)
8ms (typ), 16ms(max)
N=4 CCFLs (Cold Cathode Florescent Tube)
50,000 hours (min)

2.
INPUT SIGNAL

Video

Sync

RGB Analog (75 ohms, 0.7 / 1.0 Vp-p)

H/V Separated (TTL)
F

H

:30 – 82 kHz, fV:56-75Hz

3.

COMPATIBILITY

PC
Mac*

PC Compatibles ( VGA 1280*1024 Non Interlaced)
Power Mac (1280*1024)

4.

RESOLUTION

Recommended

Supported

1280*1024 @ 60Hz

640 x 350 ,640 x 400, 640 x 480 ,720 x 400
800 x 600 , 832 x 624,1280*1024

5.

CONNECTORS

Signal
Power
audio

15 pin mini D-sub,DVI-D
3 pin AC plug In
Stereo min audio line in

6.

POWER

Voltage
Consumption

Integrated AC 100-240V (Universal)

55W (max)

7. AUDIO

Amplifier
speaker

1.5W

1.5W x 2

8.
ERGONOMICS

Tilt

Forward
Back

Base

5 Degrees
20 Degrees for normal use,

80mm height adjustment
360 degree swivel

9.

CONTROLS

Physical

OSD Function

Main Menu

Power , [;X] [1], [▼], [▲], [2]

Auto Image Adjust, Contrast/Brightness, Input Select
Audio, Color adjust, Information, Manual Image Adjust,
Setup Menu , Memory Recall

10. BANDWIDTH 140 MHz (MAX)

11.

OPERATING

CONDITION

Temperature
Humidity

41°F to 95°F (5°C to 35°C)
20% to 80% (no condensation)

12. STORAGE /

SHIPPING

CONDITION

Temperature
Humidity

-4°F to 131 °F (-20°C to 55°C)°
20% to 85% (no condensation)

Physical(W*H*D) With stand

VESA
mount

386.8 x 474.2 x 230.0 ( mm ), 15.2 x 18.6 x 9.0 (in)

100x100mm

13. DIMENSIONS

Packaging(W*H*D) 445 x 552 x 278 (mm ) 17.5. x 21.7x 10.9(in)
Net

4.9 kg , 10.8 lbs

14. WEIGHT

Gross

6.5 kg ,13.2 lbs (including carton, EPS & cables)

15. REGULATIONS

CB / TCO03/ YCO03/ UL/cUL / FCC-B / ICES 003

/
Argentina-TUV/S / NOM / EPA Energy Star / TUV/Ergo /
ISO13406-2 / TUV/GS / CE / GOST-R / SASO / BSMI /
PSB / C-Tick / MIC/CCC

16. RELIABILITY MTBF

50000 Hr (Panel).

VG730m-3_VA730m-1

ViewSonic Corporation Confidential - Do Not Copy

6

17.

POWER SAVING

FUNCTION

"On"
" Active Off"

BLUE
AMBER

40W (max) , 35(typ)
<1 W (typ)

18.

LOGISTICS

Container Load

Pallet Load

UPC Code (UPC-A)
PC Code(ITF-14)

Serial Format

40’/20’
sea

728 / 336 units
28 pcs per pallet
7 66907 22743 7
0 07 66907 22743 7
QBYYYWWKxxxx

19. SECURITY

Kensington Lock on the bottom right side

20.

EU Packaging

Information

1. Weight of the individual (empty) shipping carton.---------------0.65 kg

2. Weight and materials of the poly foam.----------------------------90g/set,EPS

3. Weight and material of the empty accessory plastic bags ------20g/PE-LD

4. Weight and material of the plastic handle.------------------------12 g/PE-LD

5. Weight and material of the pallets ... 16Kg, popar ;

…16Kg., Fumigation wood,

21. ACCESSORIES

1. Power cable

2. analog D-sub video cable

3. audio cable

4. Quick Start Guide and CD-wizard

Support Timings

Item Timing Analog Digital

1 640 x 350 @ 70Hz, 31.5kHz Yes Yes
2 640 x 400 @ 60Hz, 31.5kHz Yes Yes
3 640 x 400 @ 70Hz, 31.5kHz Yes Yes
4 640 x 480 @ 50Hz, 24.7kHz Yes No
5 640 x 480 @ 60Hz, 31.5kHz Yes Yes
6 640 x 480 @ 67Hz, 35.0kHz Yes Yes
7 640 x 480 @ 72Hz, 37.9kHz Yes Yes
8 640 x 480 @ 75Hz, 37.5kHz Yes Yes
9 640 x 480 @ 85Hz, 43.27kHz No No

10 720 x 400 @ 70Hz, 31.5kHz Yes Yes

11 800 x 600 @ 56Hz, 35.1kHz Yes Yes
12 800 x 600 @ 60Hz, 37.9kHz Yes Yes
13 800 x 600 @ 75Hz, 46.9kHz Yes Yes
14 800 x 600 @ 72Hz, 48.1kHz Yes Yes
15 800 x 600 @ 85Hz, 53.7kHz No No
16 832 x 624 @ 75Hz, 49.7kHz Yes Yes
17 1024 x 768 @ 60Hz, 48.4kHz Yes Yes
18 1024 x 768 @ 70Hz, 56.5kHz Yes Yes
19 1024 x 768 @ 72Hz, 58.1kHz Yes Yes
20 1024 x 768 @ 75Hz, 60.0kHz Yes Yes
21 1024 x 768 @ 85Hz, 68.67kHz No No
22 1152 x 864 @ 75Hz, 67.5kHz Yes Yes
23 1152 x 870 @ 75Hz, 68.7kHz Yes Yes
24 1280 x 1024 @ 60Hz, 63.4kHz Yes Yes
25 1280 x 1024 @ 75Hz, 79.97kHz Yes Yes
26 1280x 720 @ 60Hz, 45kHz (HDTV) Yes Yes

VG730m-3_VA730m-1

ViewSonic Corporation Confidential - Do Not Copy

7

3. Front Panel Function Control Description

Adjusting the Screen Image

Main Menu

with OSD controls

Front Control Panel

shown below in detail

Scrolls through menu options and adjusts the displayed control.
Also a shortcut to display the Contrast adjustment control screen.

Power light
Blue = ON
Orange = Power Saving

Standby Power On/Off

Displays the Main Menu or exits the control screen and saves
adjustments.

Audio Mute button turns the sound off

Displays the control screen for the highlighted control.
Also toggles between two controls on some screens.

VG730m-3_VA730m-1

ViewSonic Corporation Confidential - Do Not Copy

8

Do the following to adjust the display setting:

1. To display the Main Menu, press button [1].

NOTE: All OSD menus and adjustment screens disappear automatically after about 15

seconds. This is adjustable through the OSD timeout setting in the setup menu.

2. To select a control to adjust, pressSorTto scroll up or down in the Main Menu.

3. After the desired control is selected, press button [2]. A control screen like the one shown

below appears.

4. To adjust the setting, press the up S or down T buttons.

5. To save the adjustments and exit the menu, press button [1] twice.

The following tips may help you optimize your display:

• Adjust the computer's graphics card so that it outputs a 1280 x 1024 @ 60Hz video signal to

the LCD display. (Look for instructions on “changing the refresh rate” in the graphics card's
user guide.)

• If necessary, make small adjustments using H. POSITION and V. POSITION until the

screen image is completely visible. (The black border around the edge of the screen should
barely touch the illuminated “active area” of the LCD display.)

The command line at the bottom of the
control screen tells what to do next from
this screen. You can toggle between control
screens, adjust the selected option, or exit
the screen.

VG730m-3_VA730m-1

Main Menu Controls

Adjust the menu items shown below by using the up S and down T buttons.

Control Explanation

Auto Image Adjust sizes and centers the screen image automatically.

Contrast adjusts the difference between the image background (black level)

and the foreground (white level).

Brightness adjusts background black level of the screen image.

Input Select toggles between inputs if you have more than one computer

connected to the VG730m.

Audio Adjust
Vol ume increases the volume, decreases the volume, and mutes the audio.
Mute temporarily silences audio output.

Color Adjust provides several color adjustment modes, including preset color

temperatures and a User Color mode which allows independent adjustment of
red (R), green (G), and blue (B). The factory setting for this product is 6500K
(6500 Kelvin).

sRGB-This is quickly becoming the industry standard for color management,
with support being included in many of the latest applications. Enabling this
setting allows the LCD display to more accurately display colors the way they
were originally intended. Enabling the sRGB setting will cause the Contrast and
Brightness adjustments to be disabled.

9300K-Adds blue to the screen image for cooler white (used in most office
settings with fluorescent lighting).

7500K-Adds blue to the screen image for cooler white (used in most office
settings with fluorescent lighting).

6500K-Adds red to the screen image for warmer white and richer red.

5400K-Adds green to the screen image for a darker color.

ViewSonic Corporation Confidential - Do Not Copy

9

VG730m-3_VA730m-1

Control Explanation

User Color Individual adjustments for red (R), green (G), and blue (B).

1. To select color (R, G or B) press button [2].

2. To adjust selected color, pressSandT.

Important: If you select RECALL from the Main Menu when the product is

set to a Preset Timing Mode, colors return to the 6500K factory preset.

Information displays the timing mode (video signal input) coming from the
graphics card in the computer, the LCD model number, the serial number, and
the ViewSonic® website URL. See your graphics card’s user guide for
instructions on changing the resolution and refresh rate (vertical frequency).
NOTE: VESA 1280 x 1024 @ 60Hz (recommended) means that the resolution
is 1280 x 1024 and the refresh rate is 60 Hertz.

Manual Image Adjust

H. Size (Horizontal Size) adjusts the width of the screen image.

H./V. Position (Horizontal/Vertical Position) moves the screen image left or

right and up or down.

ViewSonic Corporation Confidential - Do Not Copy

VG730m-3_VA730m-1

10

Control Explanation

Fine Tune sharpens the focus by aligning text and/or graphics with pixel
boundaries.

NOTE: Try Auto Image Adjust first.

Sharpness adjusts the clarity and focus of the screen image.

Setup Menu displays the menu shown below:

Language Select allows the user to choose the language used in the menus and

control screens.

Resolution Notice allows the user to enable or disable this notice.

If you enable the Resolution Notice shown above and your computer is set at a

resolution other than 1280 x 1024, the following screen appears.

OSD Position allows the user to move the OSD menus and control screens.

OSD Timeout sets the length of time the OSD screen is displayed. For example,

with a “30 second” setting, if a control is not pushed within 30 seconds, the
display screen disappears.

ViewSonic Corporation Confidential - Do Not Copy

11

VG730m-3_VA730m-1

Control Explanation

OSD Background allows the user to turn the OSD background On or Off.

Memory Recall returns the adjustments back to factory settings if the display is

operating in a factory Preset Timing Mode listed in the Specifications of this
manual.

ViewSonic Corporation Confidential - Do Not Copy

12

VG730m-3_VA730m-1

ViewSonic Corporation Confidential - Do Not Copy

4. Circuit Description

1. Power Board

Electric Spec :

Connection 9Pin NO. 6Pin NO. Symbol Description

9 NC DC-Output 24.0±10%Vdc / 50mA (Optional)
8 NC DC-Output 12±10%Vdc / 200mA (Optional)
7 6 BL-Adj Luminance Control ( 0Vdc~3.3Vdc )
CON802 6 5 ON/OFF ON : 3.3Vdc or 5.0Vdc ; OFF : 0V

4.5 3.4 DC-Output 5.0±5%Vdc / 2500mA

2.3 1.2 GND GND
1 NC DC-Output -8±10%Vdc / 100mA(Optional)

1 1 H.V High Voltage

CON901~CON904

2 2 Return Return Pin

13

VG730m-3_VA730m-1

ViewSonic Corporation Confidential - Do Not Copy

ELECTRIC TEST

1.POWER TEST :
1-1 .OUTPUT VOLTAGE TEST : Output 24V connect 50mA, CON801 Input

1-2 .HI-POT TEST :

1) Test Requirements – Input Voltage : 3.0KVdc
– Measurement Time : 3sec

– Temperature : 25 ± 5 ℃℃

2) A method of measurement : Injection voltage between Utility (Line and Neutral short) and output

line (short between + and - )

3) Criterion for Judging : PASS

1-3 .SHORT TEST PROTECT :

24Vdc SHORT to GND , POWER PROTECT .

12Vdc SHORT to GND , POWER PROTECT .

5Vdc SHORT to GND , POWER PROTECT .

-8Vdc SHORT to GND , POWER PROTECT .

1-4 .LOW POWER CONSUMPTION: Input 240Vac/50Hz Output NO

LOAD , Power Consumption 0.5W . 1≦ -5 .GROUND TEST :

1) Test Requirements – Input Current : 25A
– Measurement Time : 3sec

– Temperature : 25 ± 5 ℃℃

2) A method of measurement : Injection current between Utility F.G. (inlet socket F.G.) and

output ground (heat sink)

3)Criterion for Judging : Resistor 100mΩ≦

14

VG730m-3_VA730m-1

ViewSonic Corporation Confidential - Do Not Copy

1-6 .Insulation Resistance

1) Test Requirements – Input Voltage : 500Vdc

– Temperature : 25 ± 5 ℃℃

2) A method of measurement : Test between Utility (live and neutral short) and output line (+ and - short).

(insulation resistance test)

3) Criterion for Judging : Insulation resistance 100MΩ 2≧ .INVERTER TEST: 2-1.OPEN LAMP
PROTECT TEST :

Test Condition : ON/OFF PIN=3.3Vdc or 5.0Vdc , BL-Adj PIN=3.3Vdc or 5.0Vdc . Result : CN901~CN904

OPEN , INVERTER TURN ON CONTINUE 1~2 SECONDS SHUT DOWN .

2-2. KICK-OFF VOLTAGE TEST :

Test Condition : ON/OFF PIN=3.3Vdc or 5.0Vdc , BL-Adj PIN=3.3Vdc or 5.0Vdc .

Result : CN901~CN903 TEST CN904 H.V PIN Output Voltage≧1.5KV rms .

CN902~CN904 CONNECT TEST CN901 H.V PIN Output Voltage≧1.5KV rms .

CN903 .CN904 .CN901 CONNECT TEST CN902 H.V PIN Output Voltage≧ 1.5KV rms .

CN901 .CN902 .CN904 CONNECT TEST CN903 H.V PIN Output Voltage≧ 1.5KV rms .

2-3 . OUTPUT CURRENT TEST :

Test Condition Result

CN802 Pin

24V GND

CN802

BL-Adj

PIN

CN802 Pin

ON/OFF

CN901~CN904

6.5±0.5mA /

50±5KHz

22~28Vdc 3.3Vdc

3.3Vdc or

5.0Vdc

17'' or 19''

PANEL

7.0±0.5mA /

50±5KHz

7.5±0.5mA /

50±5KHz MEET L

NEED

Jumper

22~28Vdc 0Vdc

3.3Vdc or

5.0Vdc

17'' or 19''

PANEL

3.5±0.5mA

22~28Vdc

0Vdc or

3.3Vdc

0Vdc

17'' or 19''

PANEL

NO Output

 OLD TEST

CN801 Input 100~240Vac , CN802 BL-Adj Pin CONNECT 3.3Vdc , CN802 ON/OFF Pin CONNECT

3.3Vdc OR 5.0Vdc ,

 ATTENTION

1.WHEN OPERATION, WEAR STATIC ELECTRICITY RING AND KEEP GND.

2.TO PREVENT A SHORT CIRCUIT.

3.CON801 / C809 / C802 / C803 / BD801/ Q801 / T801/T802/T901/ THESE LARGE VOLUM MUST

WEIGHT A LOT

..

15

VG730m-3_VA730m-1

ViewSonic Corporation Confidential - Do Not Copy

4.3 Scaler Board

 17 '' and 19 '' LCD MONITOR

 WORK ENVIROMENT 1.WORK ENVIROMENT TEMPERATURE : 0 ℃

∼

40 2℃ .WORK

ENVIROMENT humidity : 30%

∼

85% RH . 3.STORE ENVIROMENT TEMPERATURE :－25℃

∼

＋85 4℃ .STORE ENVIROMENT humidity : 30%

∼

90% RH

 INPUT REQUIREMENT

AC Input Voltage :100Vac ~240Vac / 50~60Hz

1.SPEC :
NO List CH 1 CH 2 CH 3 CH4

1 Channel Name -8V(Optional) +5V +12V(Optional) +24V

2

OUTPUT VOLTAGE

SPEC

-8V±10% +5V±5% +12V(11.5~13.5V) +24V±10%

1.900mA for

3

OUPUT CURRENT

SPEC

50mA 2500mA 200mA

Inverter 2.50mA

for SIP

PANEL(Optional)

4

LOWEST WORK

CURRENT

10mA 400mA 50mA 10mA

WAITTING 5V

5 Load=50~80mA , 7V ~ 12V

4.75V ~

5.25V

11.5V ~ 16V 22.6V~30V

6 Ripple & Noise 200mVp-p 100mVp-p 300mVp-p 300mVp-p

2.WAITTING MERIT

AC INPUT 240Vac , NO Load

3 (L=80mm) INTRODUCTION :
PIN NO. FOR RSDS

9 8 7 6 5 4 3 2 1

PANEL SPEC 24V 12V ADJ On/Off

5V

GND -8V

PIN NO. FOR LVDS

NC NC 6 5 4 3 2 1 NC

PANEL SPEC NC NC ADJ On/Off

5V

GND NC

16

VG730m-3_VA730m-1

ViewSonic Corporation Confidential - Do Not Copy

17

 OUTPUT VOLTAGE RISE TIME AC INPUT 90 Vac ~264Vac, <100mS .

 AC ELECTRICITY TIME DELAY WHEN AC INPUT , OUTPUT VOLTAGE SHOULD WITHIN

1.5S .

 SURGE ELECTRI CURRENT AC INPUT 240Vac .

 PROTECT FOR SHORT CIRCUIT

 PROTECT FOR OVER-CURRENT

Input Voltage(V) Output(V) Output Current limits (A)

+24 <2A
90Vac~264Vac +12 <4

+5 <6 47~63Hz

-8 <4

 PROTECT FOR OVER-CURRENT

VG730m-3_VA730m-1

ViewSonic Corporation Confidential - Do Not Copy

18

Output Voltage (V) Voltage limit (V)
24 38
12 20

 Hi-POT TEST 3KVac / 3Sec

 INSULATION IMPEDANCE INPUT 500Vdc , INSULATION IMPEDANCE > 100M Ohm
 GND TEST INPUT 25Adc / 3 Sec , RESISTANCE CONNECT GROUNS <100m Ohm

 INVERTER INTRODUCTION : 17 '' and 19 '' PANEL LCD MONITOR

1.-4 lamp type of 17 '' and 19 '' PANEL

2. SPEC REQUIREMENT

Items Sign. Condition Min Typ Max

BL-ADJ=0V 3.0 3.5 4.0

6.0 6.5 7.5

1 Output Current (mA)

6.5 7.0 7.5

Lout1.2 Vin=24V

BL-ADJ=3.3V

7.0 7.5 8.0
2 Output Voltage (Vrms) Vin=24V BL-ADJ=3.3V 560 660 760
3 Lamp Frequency (kHz) f Vin=24V BL-ADJ =3.3V 45 50 55

On Vin=24V, On/Off=3.3V or 5V Normal Operation

4 On/Off Control

Off Vin=24V, On/Off=0V Shunt-down (Lamp off)

BL-ADJ = 3.3V, Max Current

5

Dim Adjust (Lamp
Current Control)

BL-ADJ

BL-ADJ = 0V, Min Current

0V ~ 3.3V

6 Kick-Off Voltage(Vrms) Vk-off Kick-Off More than 1500

 MTBF MTBF 100000 HOUR 25°C

 MACHINERY SIZE

VG730m-3_VA730m-1

ViewSonic Corporation Confidential - Do Not Copy

19

4.4 EDID Data

[DDC#1]
00 FF FF FF FF FF FF 00 5A 63 1E 95 01 01 01 01
01 10 01 03 80 22 1B 78 2E DC 55 A3 59 48 9E 24
11 50 54 BF EF 80 81 80 81 40 71 4F 31 0A 01 01
01 01 01 01 01 01 30 2A 00 98 51 00 2A 40 30 70
13 00 52 0E 11 00 00 1E 00 00 00 FF 00 51 42 59
30 36 30 31 30 30 30 30 31 0A 00 00 00 FD 00 32
4B 1E 52 0E 00 0A 20 20 20 20 20 20 00 00 00 FC
00 56 47 37 33 30 6D 0A 20 20 20 20 20 20 00 75
[DDC#1]
00 FF FF FF FF FF FF 00 5A 63 1E 95 01 01 01 01
01 10 01 03 0E 22 1B 78 2E DC 55 A3 59 48 9E 24
11 50 54 BF EF 80 81 80 81 40 71 4F 01 01 01 01
01 01 01 01 01 01 30 2A 00 98 51 00 2A 40 30 70
13 00 52 0E 11 00 00 1E 00 00 00 FF 00 51 42 59
30 36 30 31 30 30 30 30 31 0A 00 00 00 FD 00 32
4B 1E 52 0E 00 0A 20 20 20 20 20 20 00 00 00 FC
00 56 47 37 33 30 6D 0A 20 20 20 20 20 20 00 20

4.5 Interface

4.5.1.1Pin Assignment

D-SUB connector:CN2

Pin Input Signal Pin Input Signal Pin Input Signal

1 Red video 6 Red Video Ground 11 Open
2 GreenVideo/Sync on Green 7 Green Video Ground 12 Data line (SDA)*
3 Blue Video 8 Blue Video Ground 13 H-Sync
4 Ground 9 +5V (for cable detect) 14 V-Sync
5 Ground 10 Connector detector 15 Clock line (SCL)*

*Compliant to VESA DDC.

4.5.1.2Audio Input (line-in)

Item Specifications

Input Voltage 1 Vrm s
Output Power 1 W dual channel output

VG730m-3_VA730m-1

ViewSonic Corporation Confidential - Do Not Copy

20

5. Adjusting Procedure

1. Function test

1.1 products

17” LCD Monitor

2. Firmware and EDID upgrade/update Methods

Firmware Update Procedure

1. The monitor’s firmware update for VG730 have two method.

1.1. Download the MCU IC by the fire machine. This procedure is finished in SMT .

1.2. ISP Method. When the monitor’s BIOS isn’t exist or firmware isn’t final program, this method Is

worked by ISP Cord with monitor

2.1 Equipment Needed

2. VG730 monitor upgrade firmware by ISP Cord.

- USB cable for print port *1

- VGA cable*1

- LPT cable (25pin)*1

- AC power cable*1

- ISP fire cord ( the fixture is made in TE ) for firmware upgrade*1

- Power adapter for firmware upgrade (this adapter is made in TE)*1

- A computer with WindowsXP

- VG730 monitor ( no firmware)

- a additional monitor for system display

- ISP & ISP3.0 program

NOTE:

The fixture for firmware upgrade provide two different method to fire. Please check you monitor’s Main board,

refer to MCU-RSIC type and choose the method. Below form appear the relation between the method and the

MCU-RSIC type

METHOD

MCU ASIC JUMPER
A MYSON M-STAR & NOVATEK PIN2-3 CLOSED
B OTHER REALTEK PIN1-2 CLOSED

VG730m-3_VA730m-1

ViewSonic Corporation Confidential - Do Not Copy

21

TEST PC

Fixture ISP_CORD Fixture POWER_ADAPTER

LPT PORT

LPT Cable

AC power Cable

VGA Cable

USB FOR PRINT

ISP3.0 SOFT

VG730m-3_VA730m-1

ViewSonic Corporation Confidential - Do Not Copy

22

2.2. Setup Procedure

4.2.1 Connect PO1 of ISP fixture with print port of computer by LPT cable

4.2.2 Connect PO2 of ISP fixture with USB port of computer by USB cable

4.2.3 Connect PO3 of ISP fixture with monitor VGA port by VGA cable

4.2.4 Connect mouse, keyboard, AC power, monitor with computer

4.2.5 Plug AC cable in power adapter AC jack

4.2.6 Connect power adapter DC_OUTPUT port to main board DC_IN port

4.2.7 Connect PO3 of ISP fixture with VGA port of monitor’s main board by VGA cable

NOTE:

Do STEP2.2.6 and STEP2.2.7 for monitor’s main board only. Monitor firmware upgrade will jump this step.

PO2 to USB cable

PO1 to LPT cable

PO3 to VGA cable

jumper

AC JACK

DC_IN port

VGA port

VG730m-3_VA730m-1

ViewSonic Corporation Confidential - Do Not Copy

23

2.3. Soft install

Install ISP3.0 program by selecting and clicking “…\isp3.0\setup.exe”, press “YES” or “NEXT” buttons until

setup is complete.

VG730m-3_VA730m-1

ViewSonic Corporation Confidential - Do Not Copy

24

VG730m-3_VA730m-1