ViewSonic VE155 - 15"" LCD Monitor, ViewPanel VE155 User Manual

Page 1

VE155 ViewPanel

User Guide Guide de l’utilisateur Bedienungsanleitung Guía del usuario Guida dell'utente Guia do usuário Användarhandbok Käyttöopas

Full 15.0" Diagonal Viewable Screen

Jmdh\h^kl\hihevah\Zl_ey

,QVWUXNFMDREVáXJL

Page 2

Contents

Product Registration..............................................................2

For Your Records ..................................................................2

Getting Started

Package Contents .................................................................3

Precautions ...........................................................................3

Quick Installation ...................................................................4

Installation of Wall Mount (Optional) .....................................5

Using the ViewPanel

Setting the Timing Mode .......................................................6

OSD and Power Button Lock Modes.....................................6

Adjusting the Screen Image ..................................................7

Main Menu Controls ..............................................................9

Other Information

Specifications ......................................................................13

Troubleshooting...................................................................14

Customer Support ...............................................................15

Cleaning the ViewPanel ......................................................16

Limited Warranty .................................................................17

Appendix

Safety Guidelines ................................................................18

Compliance Information for U.S.A.......................................19

CE Conformity for Europe ...................................................19

ViewSonic VE155 106/14/02 B

Page 3

Copyright © ViewSonic Corporation, 2002. All rights reserved. Macintosh and Power Macintosh are registered trademarks of Apple Computer, Inc. Microsoft, Windows, Windows NT, and the Windows logo are registered trademarks of Microsoft

Corporation in the United States and other countries. ViewSonic, the three birds logo, OnView, ViewMatch, and ViewMeter are registered trademarks of

ViewSonic Corporation. VESA is a registered trademark of the Video Electronics Standards Association. DPMS and DDC

are trademarks of VESA.

NERGY STAR

As an E E

NERGY STAR

is a registered trademark of the U.S. Environmental Protection Agency (EPA).

partner, ViewSonic Corporation has determined that this product meets the

guidelines for energy efficiency.

Disclaimer: ViewSonic Corporation shall not be liable for technical or editorial errors or omissions contained herein; nor for incidental or consequential damages resulting from furnishing this material, or the performance or use of this product.

In the interest of continuing product improvement, ViewSonic Corporation reserves the right to change product specifications without notice. Information in this document may change without notice.

No part of this document may be copied, reproduced, or transmitted by any means, for any purpose without prior written permission from ViewSonic Corporation.

Product Registration

To meet your future needs, and to receive any additional product information as it becomes available, please register your product on the Internet at:

www.viewsonic.com.

Wizard CD-ROM also provides an opportunity for you to print the registration form, which you may mail or fax to ViewA3Tm[(Pr)20198 duct Redisse pr the to thp20198 duct Reli8.2(e)23J/F11 1 Tf 0.00091 Tc -0.00100Tw 7.98 0 0 7.98 222.92 39249.1 Tm[( p61.3(i)0.8(e)23.9(w)-21(w)nic )] donticnet d abt pre perserv3meon fo thr prenvironmental. Pase redisse of this product.

The ViewSonic

Page 4

Getting Started

Congratulations on your purchase of a ViewSonic® ViewPanel®. Important!

Save the original box and all packing material for future shipping needs.

NOTE: The word “Windows” refers to Microsoft Windows 95, 98, NT, XP, 2000 and Me (Millennium Edition).

Package Contents

IMPORTANT: Save all packing material. Your ViewPanel package includes:

• ViewPanel

• Power cords

• ViewSonic Wizard CD-ROM

NOTE:

The CD jacket contains the Quick Start Guide, and the CD includes User Guide PDF files and INF/ICM display optimization files. The INF files ensures compatibility with Windows operating systems, and the ICM file (Image Color Matching) ensures accurate on-screen colors. ViewSonic recommends that you install both files.

Precautions

• Sit at least 18" from your ViewPanel.

Avoid touching the screen.

• difficult to remove.

Never remove the rear cover.

• ViewPanel contains high-voltage parts. You may be seriously injured if you touch them.

• Avoid exposing your ViewPanel to direct sunlight or another heat source. Orient your ViewPanel away from direct sunlight to reduce glare.

• Always handle your ViewPanel with care when moving it.

Skin oils are

Your

• Place your ViewPanel in a well-ventilated area. Do not place anything on your ViewPanel that prevents heat dissipation.

• Ensure the area around the V iewP anel is clean and free of moisture.

• Do not place heavy objects on the V iewPanel, video cable, or power cord.

• If smoke, abnormal noise, or strange odor is present, immediately switch the ViewPanel off and call your dealer or ViewSonic. It is dangerous to continue using the ViewPanel.

ViewSonic VE155 3

Page 5

Quick Installation

Optional:

see page 5 of this user guide.

For instructions on wall mounting,

1 Connect power cord 2 Connect video cable

• Make sure both the ViewPanel® and computer are turned OFF

• Connect the video cable from the ViewPanel to the computer

Macintosh user s: Models older than G3 require a Macintosh adapter. Attach the adapter to the computer and plug the video cable into the adapter.

To order a ViewSonic contact ViewSonic Customer Support.

Macintosh adapter,

3 Turn ON ViewPanel and computer

• Turn ON the ViewPanel, then turn ON the computer. This sequence (ViewPanel before computer) is important.

NOTE:

receive a message asking them to install the INF file. This is on the CD.

Windows 95, 98 or 2000 users may

4 Insert the ViewSonic Wizard CD

into the computer’s CD drive

• Follow the on-screen instructions.

If your computer does not have a CD-ROM drive, see “Customer Support.”

(1) Wait for the CD-ROM to auto-start.

NOTE:

double-click on the CD-ROM icon in the Windows Explorer, then double-click on

viewsonic.exe.

(2) Follow the on-screen instructions.

If the CD-ROM does not auto-start:

5 Windows users: Set the timing

mode (resolution and refresh rate)

Example: 1024 X 768 @ 60 Hz. For instructions on changing the resolution

and refresh rate, see the graphic card’s user guide.

Installation is complete. Enjoy your new ViewSonic ViewPanel.

To be best prepared for any future customer service needs: print this user guide and write the serial number in “For Your Records” on page 2. (See back of ViewPanel.)

You can register your product online at the website for your region. See the Customer Support table in this guide.

The ViewSonic Wizard CD-ROM also

Page 6

Installation of Wall Mount (Optional)

To obtain a wall-mounting kit, contact ViewSonic or your local dealer. Refer to the instructions that come with the base mounting kit. To convert your ViewPanel from a desk-mounted to a wall-mounted display, do the following:

Disconnect Power.

Push the ViewPanel back and down flat against the base as shown.

Four screw holes

Lay the ViewPanel face down on a towel or blanket. Notice the four screw holes on the bottom of the base.

Attach the mounting bracket from the VESA compatible wallmounting kit (75 mm x 75 mm distance).

Attach the V ie wPanel to the w all, following the instructions in the wall-mounting kit.

Mounted on the wall

ViewSonic VE155 5

Page 7

Using the ViewPanel

Setting the Timing Mode

Setting the timing mode is important for maximizing the quality of the screen image and minimizing eye strain. The timing mode consists of the reso l u tion (example 1024 x 768) and refresh rate (or vertical frequency; example 60 Hz). After setting the timing mode, use the OnView to adjust the screen image.

controls

For the best picture quality set your ViewPanel

timing mode to:

VESA 1024 x 768 @ 60 Hz.

To set the Timing Mode:

Set the resolution: Right-click on the Windows desktop > Properties > Settings > set the resolution.

Set the refresh rate: See your graphic card's user guide for instructions.

WARNING:

Do not set the graphics card in your computer to exceed the maximum refresh rate of 75Hz; doing so may result in permanent damage to your ViewPanel.

OSD and Power Button Lock Modes

OSD Lock This mode locks all current control settings and prevents access to the control menus until this mode is unlocked.

• OSD Lock: Press and hold [1] and the up arrow

buttons are pressed the message OSD Locked will display for 5 seconds.

for 10 seconds. If any

• OSD Unlock: Press and hold [1] and the up arrow Power Button Lock This mode locks the power of the ViewPanel in the ON

position.

• Power Button Lock: Press and hold [1] and the down arrow

seconds. If the power button is pressed the message Power Button Locked will display for 5 seconds. With or without this setting, after a power failure, your ViewPanel’s power will automatically turn ON when power is restored.

• Power Button Unlock: Press and hold [1] and the down arrow

10 seconds.

again for 10 seconds.

for 10

again for

ViewSonic VE155 6

Page 8

Adjusting the Screen Image

Use the buttons on the front control panel to display and adjust the OnView® controls which display on the screen. The OnView controls are explained at the top of the next page and are defined in “Main Menu Controls” on page 9.

Main Menu with OnView controls

Displays, saves changes to, and exits the Main Menu.

Scroll through menu options and adjust the displayed control.

Front Control Panel

Power light

Power On/Off

Selects a highlighted control. Also, displays the control screen for the selected control and toggles between control pairs.

ViewSonic VE155 7

Page 9

Do the following to adjust the screen image:

To display the Main Menu, press button [1].

Main Menu

AUTO

SET

1:EXIT 2:SELECT

Auto Adjust

Contrast/Brightness

Color Adjust

Information

Image Adjust

Setup Menu

Memory Recall

NOTE: All OnView menus and adjustment screens disappear automatically after about 15 seconds. This time period is adjustable through the Setup menu and the OSD timeout control described on page 11.

To highlight a control you want to adjust, press I or J to scroll up or down the Main Menu.

To select the highlighted control, press button [2]. A control screen appears like the example shown below.

Contrast

1:EXIT 2: Brightness

To adjust the control, press the up I or down J buttons.

To save the adjustments and exit the menu, press button [1] twice.

The line at the bottom of the screen tells you what you can do next: Exit or Select the control that is highlighted.

The following tips may help you optimize your display:

• Adjust your computer's graphic card so that it outputs a video signal 1024 x

768 @ 60 Hz to the ViewPanel. (Look for instructions on “changing the refresh rate” in your graphic card's user guide.)

• If necessary, make small adjustments using H. POSITION and V. POSITION

until the screen image is completely visible

. (The black border around the edge of the screen should barely touch the illuminated “active area” of the ViewPanel

ViewSonic VE155 8

Page 10

Main Menu Controls

Adjust the menu items shown below by using the up Iand down Jbuttons.

Control Explanation

Auto Adjust

automatically sizes, centers, and fine tunes the

video signal to eliminate waviness and distortion.

Press the [2] button to obtain a sharper image.

NOTE

this function does not work on your ViewPanel

: Auto Adjust works with most common video cards. If

, then lower the video refresh rate to 60 Hz and set the resolution to its pre-set value.

Contrast

adjusts the difference between the image background

(black level) and the foreground (white level).

Brightness

Color Adjust

adjusts background black level of the screen image.

provides several color options: preset color

temperatures and User which allows you to adjust red (R), green (G), and blue (B). The factory setting for this product is 6500K (6500 Kelvin).

Color Adjust

9300K

6500K

User Color

1:EXIT 2:SELECT

9300K

— Adds blue to the screen image for cooler white (used

in most office settings with fluorescent lighting).

6500K

— Adds red to the screen image for warmer white and

richer red. Default setting.

User

— Individual adjustments for red, green, and blue.

To select color (R, G or B) press button [2].

To adjust selected color, press I or J.

When you are finished making all color adjustments, press button [1] twice.

ViewSonic VE155 9

Page 11

Control Explanation

coming from the graphics card in your computer. See your

Information

displays the timing mode (video signal input)

graphic card’s user guide for instructions on changing the resolution and refresh rate (vertical frequency).

VESA 1024 x 768 @ 60 Hz (recommended) means that the resolution is 1024 x 768 and the refresh rate is 60 Hertz.

Information

H. Frequency: 48.60 KHz

V. Frequency: 60.00 Hz

Pixel Clock: 65.00 MHz

Resolution: 1024 x 768

Model Number: VLCDS23585-1W

Serial No:

www.viewsonic.com

1:EXIT

Image Adjust

H./V. Position

H. Size

Fine Tune

Sharpness

1:EXIT 2:SELECT

The Image Adjust controls are explained below:

H./V. Position

adjusts horizontal and vertical position of the screen image. You can toggle between Horizontal and Vertical by pressing button [2]. Horizontal moves the screen image to the left or to the right. Vertical moves the screen image up and down.

H. Size

NOTE:

(Horizontal Size) adjusts the width of the screen image.

Vertical size is automatic with your ViewPanel®.

ViewSonic VE155 10

Page 12

Control Explanation

Fine Tune sharpens focus by aligning the illuminated text and/

or graphic characters.

NOTE: Try the Auto Adjust (see page 9) before using the Fine

Tune control.

Sharpness

adjusts the clarity and focus of the screen image.

Setup Menu displays the menu shown below.

Setup Menu

1:EXIT 2:SELECT

Page 13

Control Explanation

Memory Recall

returns adjustments to the original factory settings if the display is operating in a factory Preset Timing Mode listed in this user guide.

ViewSonic VE155 12

Page 14

Other Information

Specifications

LCD

Panel tilt

+20°

Input signal

Compatibility

Resolution

Power Display area

Operating conditions

Storage conditions

Type

Color Filter Glass surface

Video Sync RGB analog (0.7/1.0 Vp-p, 75 ohms)

PC Macintosh

Recommended and supported

Voltage 100-240 VAC, 50/60 Hz (auto switch) Full Scan 304.1mm (H) x 228.1 mm (V)

Temperature Humidity Altitude

15" (full 15" viewable diagonal area), TFT (Thin Film Transistor), Active Matrix XGA LCD , 0.297mm pixel pitch RGB vertical stripe Anti-Glare

, -5°

Separate Sync,

:30-62 kHz, fv:50-75 Hz

Up to 1024 x 768 Non-interlaced Power Macintosh

1024 x 768 @ 60, 70, 72, 75 Hz 800 x 600 @ 56, 60, 72, 75 Hz 640 x 480 @ 60, 75 Hz 832 x 624 @ 75 Hz 720 x 400 @ 70 Hz

12.0" (H) x 9.0" (V) 32° F to + 104° F (0° C to + 40° C)

10% to 90% (no condensation) To 10,000 feet (3,000m)

-4° F to + 140° F (-20° C to + 60° C) 10% to 90% (no condensation) To 40,000 feet (12,000m)

up to 1024 x 768

Dimensions

Weight Regulations

Power saving modes

Preset Timing Mode

Warning:

result in permanent damage to the ViewPanel.

Macintosh computers older than G3 require a ViewSonic®, Macintosh adapter. To order an adapter,

contact ViewSonic.

Do not set the graphics card in your computer to exceed these refresh rat es; doing so may

Physical 356 mm (W) x 344 mm (H) x 200 mm (D)

14.02" (W) x 13.52" (H) x 7.87" (D)

Net 3.7 kg (8.1 lb)

On Normal (green LED) Active Off <2W (orange LED)

(pre-adjusted to VESA® 1024 x 768 @ 60 Hz)

NERGY STAR

UL, FCC-B, NEMKO, SEMKO, DEMKO, FIMKO, C-UL, TCO99, TUV-S, EPA, E2002, VCCI, BSMI, CB, ISO13406-2, Gost-R, PCT (BZ02)

, FCC-B (Doc-B), CE, MPRII,

ViewSonic VE155 13

Page 15

Troubleshooting

No power

• Make sure power button (or switch) is ON.

• Make sure A/C power cord is securely connected to the ViewPanel

• Plug another electrical device (like a radio) into the po wer outlet to verify that the outlet is supplying proper voltage.

Power is ON but no screen image

• Make sure the video cable supplied with the ViewPanel is tightly secured to the video output port on the back of the computer. If the other end of the video cable is not attached permanently to the ViewPanel, tightly secure it to the ViewPanel.

• Adjust brightness and contrast.

• If you are using an Macintosh older than G3, you need a Macintosh adapter.

Wrong or abnormal colors

• If any colors (red, green, or blue) are missing, check the video cable to make sure it is securely connected. Loose or broken pins in the cable connector could cause an improper connection.

• Connect the ViewPanel to another computer.

• If you have an older graphics card, contact ViewSonic

for a non-DDC

adapter.

Control buttons do not work

• Press only one button at a time.

ViewSonic VE155 14

Page 16

Customer Support

For technical support or product service, see the table below or contact your reseller.

NOTE:

Country/ Region

United States

Canada

United Kingdom viewsoniceurope.com T: 0800 833 648

/om

You will need the product serial number.

Web site T = Telephone

F = FAX

viewsonic.com/ support

T: (800) 688-6688 F: (909) 468-1202

F: (01293) 643910

service.us@ viewsonic.com

service.ca@ viewsonic.com

service.eu@ viewsoniceurope.com

Page 17

Cleaning the ViewPanel

• MAKE SURE THE VIEWPANEL® IS TURNED OFF.

• NEVER SPRAY OR POUR ANY LIQUID DIRECTLY ONTO THE

SCREEN OR CASE.

To clean the screen:

Wipe the screen with a clean, soft, lint-free cloth. This removes dust and other particles.

If still not clean, apply a small amount of non-ammonia, non-alcohol based glass cleaner onto a clean, soft, lint-free cloth, and wipe the screen.

To clean the case:

Use a soft, dry cloth.

If still not clean, apply a small amount of a non-ammonia, non-alcohol based, mild non-abrasive detergent onto a clean, soft, lint-free cloth, then wipe the surface.

Disclaimer

ViewSonic

does not recommend the use of any ammonia or alcohol-based cleaners on the V i ewPanel screen or case. Some chemical cleaners have been reported to damage the screen and/or case of the ViewPanel. ViewSonic will not be liable for damage resulting from use of any ammonia or alcohol-based cleaners.

ViewSonic VE155 16

Page 18

Limited Warranty

VIEWSONIC LCD VIEWPANEL

What the warranty covers:

ViewSonic

warranty period. If a product proves to be defective in material or workmanship during the warranty period, product or parts may include remanufactured or refurbished parts or components.

How long the warranty is effective: ViewSonic

three (3) years for all labor from the date of the first consumer purchase.

Who the warranty protects:

This warranty is valid only for the first consumer purchaser.

What the warranty does not cover:

1. Any product on which the serial number has been defaced, modified or removed.

2. Damage, deterioration or malfunction resulting from: a. Accident, misuse, neglect, fire, water, lightning, or other acts of nature, unauthorized product

b. Repair or attempted repair by anyone not authorized by c. Any damage of the product due to shipment. d. Removal or installation of the product. e. Causes external to the product, such as electrical power fluctuations or failure. f. Use of supplies or parts not meeting g. Normal wear and tear. h. Any other cause which does not relate to a product defect.

3. Removal, installation, and set-up service charges.

How to get service:

1. For information about receiving service under warranty, contact You will need to provide your product's serial number.

2. To obtain service under warranty, you will be required to provide (a) the original dated sales slip, (b) your name, (c) your address, (d) a description of the problem, and (e) the serial number of the product.

3. Take or ship the product freight prepaid in the original container to an authorized service center or

4. For additional information or the name of the nearest

ViewSonic

Limitation of implied warranties:

THERE ARE NO WARRANTIES, EXPRESS OR IMPLIED, WHICH EXTEND BEYOND THE DESCRIPTION CONTAINED HEREIN INCLUDING THE IMPLIED WARRANTY OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.

Exclusion of damages:

VIEWSONIC'S LIABILITY IS LIMITED TO THE COST OF REPAIR OR REPLACEMENT OF THE PRODUCT. VIEWSONIC SHALL NOT BE LIABLE FOR:

1. DAMAGE TO OTHER PROPERTY CAUSED BY ANY DEFECTS IN THE PRODUCT, DAMAGES BASED UPON INCONVENIENCE, LOSS OF USE OF THE PRODUCT, LOSS OF TIME, LOSS OF PROFITS, LOSS OF BUSINESS OPPORTUNITY, LOSS OF GOODWILL, INTERFERENCE WITH BUSINESS RELATIONSHIPS, OR OTHER COMMERCIAL LOSS, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.

2. ANY OTHER DAMAGES, WHETHER INCIDENTAL, CONSEQUENTIAL OR OTHERWISE.

3. ANY CLAIM AGAINST THE CUSTOMER BY ANY OTHER PARTY.

Effect of state law:

This warranty gives you specific legal rights, and you may also have other rights which vary from state to state. Some states do not allow limitations on implied warranties and/or do not allow the exclusion of incidental or consequential damages, so the above limitations and exclusions may not apply to you.

Sales outside the U.S.A. and Canada:

For warranty information and service on contact

ViewSonic LCD Warranty (V2.0) Release Date: 10-15-1999

warrants its products to be free from defects in material and workmanship during the

ViewSonic

LCD ViewPanels are warranted for three (3) years for all parts including the light source and

modification, or failure to follow instructions supplied with the product.

ViewSonic

will, at its sole option, repair or replace the product with a like product. Replacement

ViewSonic

’s specifications.

ViewSonic Customer Support.

ViewSonic

products sold outside of the U.S.A. and Canada,

ViewSonic

or your local

ViewSonic

dealer.

ViewSonic

service center, contact

ViewSonic VE155 17

Page 19

Appendix

Safety Guidelines

Warning:

12VDC LSE9901B1250, 12VDC UP06031120.

CAUTION: CAUTION:

fied for the individual country. Some examples are listed below:

This device must be operated with the original power supply, part number:

The socket-outlet should be installed near the equipment and should be easily accessible.

Use a power cable that is properly grounded. Always use the appropriate AC cord that is certi-

USA................. UL

Canada............. CSA

Germany..........VDE

Switzerland ..... SEV

Britain ............. BASE/BS

Japan ............... Electric Appliance Control Act

IMPORTANT NOTICE CONCERNING POWER CORD SELECTION

The power cord set for this unit has been enclosed and has been selected according to the country of destination and must be used to prevent electric shock. Use the following guidelines if it is necessary to replace the original cord set, or if the cord set is not enclosed. The female receptacle of the cord set must meet IEC-60320 requirements and may look like (Figure A1 below):

Figure A2

For the United States and Canada

In the United States and Canada the male plug is a NEMA5-15 style (Figure A2), UL Listed, and CSA Labeled. For units which are mounted on a desk or table, type SVT or SJT cord sets may be used. For units which sit on the floor, only SJT type cord sets may be used. The cord set must be selected according to the current rating for your unit. Please consult the table below for the selection criteria for power cords used in the United States and Canada.

Cord T

SJT 18 AWG

SVT 18 AWG

e Size of Conductors in Cord Maximum Current Rating of Unit

16 AWG 14 AWG

17 AWG

10 Amps 12 Amps 12 Amps

10 Amps 12 Amps

For European Countries

In Europe you must use a cord set which is appropriate for the receptacles in your country. The cord set is HARCertified, and a special mark that will appear on the outer sheath, or on the insulation of one of the inner conductors.

AC PLUG CORD PRECAUTIONS FOR THE UNITED KINGDOM

FOR YOUR SAFETY PLEASE READ THE FOLLOWING TEXT CAREFULLY.

IF THE FITTED MOULDED PLUG IS UNSUITABLE FOR THE SOCKET OUTLET THEN THE PLUG SHOULD BE CUT OFF AND DISPOSED OF SAFELY.

THERE IS A DANGER OF SEVERE ELECTRICAL SHOCK IF THE CUT OFF PLUG IS INSERTED INTO AN APPROPRIATE SOCKET.

If a new plug is to be fitted, please observe the wiring code as shown below.

If in any doubt, please consult a qualified electrician.

WARNING: IMPORTANT:

If the coloured wires of the mains lead of this appliance do not correspond with the coloured markings identifying the terminals in your plug, proceed as follows:

The wire which is coloured GREEN-AND-YELLOW must be connected to the terminal in the plug which is marked by the letter E or by the Earth symbol or coloured GREEN or GREEN-AND-YELLOW.

The wire which is coloured BLUE must be connected to the terminal in the plug which is marked with the letter N or coloured BLACK. The wire which is coloured BROWN must be connected to the terminal in the plug which is marked with the letter L or coloured RED.

If you have any questions concerning which proper power cord to use, please consult with the dealer from whom you have purchased the product.

THIS APPLIANCE MUST BE EARTHED.

The wires in this mains lead are coloured in accordance with the following code:

Green-and-Yellow: Earth Blue: Neutral Brown: Live

Page 20

Compliance Information for U.S.A.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

FCC Warning

To assure continued FCC compliance, the user must use grounded power supply cord and the provided shielded video interface cable with bonded ferrite cores. If a BNC cable is going to be used, use only a shielded BNC(5) cable. Also, any unauthorized changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this device.

Notice for Japan

This is a Class B product based on the standard of the Voluntary Control Council for Interference from Information Technology Equipment (VCCI). If this is used near a radio or television receiver in a domestic environment, it may cause radio interference. Install and use the equipment according to the instruction manual.

CE Conformity for Europe

The device complies with the requirements of the EEC directive 89/336/EEC as amended by 92/31/EEC and 93/68/EEC Art.5 with regard to “Electromagnetic compatibility”, and 73/ 23/EEC as amended by 93/68/EEC Art.13 with regard to “Safety.”

ViewSonic VE155 19

Page 21

ViewSonic Corporation