ViewSonic Q51, Q51b, VCDTS23284-8 User Manual

- User Guide

- Guide de l’utilisateur

- Guida dell’utente

- Guia do usuário

ViewSonic

®

ViewSonic

®

Q51 / Q51b

CRT Monitor

Compliance Information

For U.S.A.

This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This equipment
generates, uses, and can radiate radio frequency energy, and if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:

•  Reorient or relocate the receiving antenna.

•  Increase the separation between the equipment and receiver.

•  Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected.

•  Consult the dealer or an experienced radio/TV technician for help.

FCC Warning

To assure continued FCC compliance, the user must use grounded power supply cord
and the cables which are included with the equipment or specified. Also, any unauthorized
changes or modifications not expressly approved by the party responsible for compliance
could void the user’s authority to operate this device.

For Canada

This Class B digital apparatus meets all requirements of the Canadian Interference-Causing
Equipment Regulations.
Cet appareil numeique de la Classe B repecte toutes les exigences du Reglement sur le
materiel brouilleur du Canada.

CE Conformity for European Countries

CE Conformity

The device complies with the requirements of the EEC directive 89/336/EEC as
amended by 92/31/EEC and 93/68/EEC Art.5 with regard to “Electromagnetic
compatibility,” and 73/23/EEC as amended by 93/68/EEC Art.13 with regard to
“Safety.”

User Information for all Countries

Notice: Use the cables which are included with the unit or specified.

Important Safety Instructions

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this unit near water.

6. Clean only with dry cloth.

7. Do not block any ventilation openings. Install in accordance with the manufacturer’s

instructions.

8. Do not install near any heat sources such as radiators, heat registers, stoves, or other
devices (including amplifiers) that produce heat.

9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized
plug has two blades with one wider than the other. A grounding type plug has two
blades and a third grounding prong. The wide blade or the third prong are provided for
your safety. If the provided plug does not fit into your outlet, consult an electrician for
replacement of the obsolete outlet.

10. Protect the power cord from being walked on or pinched particularly at plugs.
Convenience receptacles and the point where they exit from the unit. Be sure that the
power outlet is located near the unit so that it is easily accessible.

11. Only use attachments/accessories specified by the manufacturer.

12. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer,

or sold with the unit. When a cart is used, use caution when moving the cart/unit
combination to avoid injury from tip-over

13. Unplug this unit when unused for long periods of time.

14. Refer all servicing to qualified service personnel. Servicing is required when the unit has

been damaged in any way, such as power-supply cord or plug is damaged, liquid has
been spilled or objects have fallen into the unit, the unit has been exposed to rain or
moisture, does not operate normally, or has been dropped.

ViewSonic Q51 1

Content

Product Registration .................................................................................................... 2

Getting Strated

Package Contents ........................................................................................................3

Precautions .................................................................................................................3

Quick Installation .........................................................................................................4

Using the Monitor

Setting the Timing Mode ..............................................................................................5

OSD Lock Settings ......................................................................................................5

Adjusting the Screen Image ........................................................................................6

Other Information

Specifications ............................................................................................................10

Troubleshooting ......................................................................................................... 11

Customer Support .....................................................................................................12

Cleaning the Monitor .................................................................................................13

Limitedd Warranty .....................................................................................................14

ViewSonic Q51 2

Copyright © ViewSonic Corporation, 2004. All rights reserved.

Macintosh and Power Macintosh are registered trademarks of Apple Computer, Inc.

Microsoft, Windows, Windows NT, and the Windows logo are registered trademarks of
Microsoft Corporation in the United States and other countries.

ViewSonic, the three birds logo, OnView, ViewMatch, and ViewMeter are registered
trademarks of ViewSonic Corporation.

VESA is a registered trademark of the Video Electronics Standards Association. DPMS and
DDC are trademarks of VESA.

Disclaimer: ViewSonic Corporation shall not be liable for technical or editorial errors or
omissions contained herein; nor for incidental or consequential damages resulting from
furnishing this material, or the performance or use of this product.

In the interest of continuing product improvement, ViewSonic Corporation reserves the right
to change product specifications without notice. Information in this document may change
without notice.

No part of this document may be copied, reproduced, or transmitted by any means, for any
purpose without prior written permission from ViewSonic Corporation.

Product Registration

To meet your future needs, and to receive any additional product information as it becomes
available, please register your product on the Internet at: www.viewsonic.com. The
ViewSonic

®

Wizard CD-ROM also provides an opportunity for you to print the registration

form, which you may mail or fax to ViewSonic.

For Your Records

Product Name:

Model Number:
Document Number:
Serial Number:
Purchase Date:

Q51
ViewSonic 15” CRT Monitor
VCDTS23284-8
Q51/B-8_UG_ENG Rev. 1B 12-15-04

___________________________________
___________________________________

Product disposal at end of product life

ViewSonic is concerned about the preservation of our environment. Please dispose of this
product properly at the end of its useful life. For TCO’03 recycling information, please refer to
our website:

1. USA: www.viewsonic.com/pdf/recyclePlus.pdf

2. Europe: www.viewsoniceurope.com

3. Taiwan: recycle.epa.gov.tw

ViewSonic Q51 3

ViewSonic Q51 4

ViewSonic Q51 5

ViewSonic Q51 6

ViewSonic Q51 7

ViewSonic Q51 8

ViewSonic Q51 9

ViewSonic Q51 10

Importantes Instrucciones de Seguridad

Specifications

CRT Type

15”(13.8” viewable diagonal area). 0.24 mm Horizontal,

0.14 mm Vertical, and 0.28 mm diagonal dot pitch, 90

o

deflection

Phosphor
Glass suface

RGB, medim-short persistence
Anti-glard, anti-static coating
Standard light transmission rate=57%

Input Signal

Video
Sync

RGB Analog (0.7/1.0 Vp-p, 75 Ohms
fH:30-54 kHz, fv:50-120 Hz
HV Separate (TTL), Composite

Compatibility

PC
Macintosh

1

VGA up to 1024 x 768 NI
Power Macintosh (up to 832 x 624)

Timing Modes
(with Mazimum Refresh Rates)

2

1024 x 768 @ 70 Hz
800 x 600 @ 89 Hz
640 x 480 @ 110 Hz

Power Voltage AC 100-240 (auto switch) 50/60 Hz

Display Area

Default
Full scan

266 mm(W) x 200 mm(V) (Typical)
284 mm(W) x 213 mm(V) (Deoebds ib sugbak tunubg)

Operating Conditions

Temperature
Humidity
Altitude

32o F to 104o F (0o C to +40o C)
5% to 95% (no condensation)
To 10,000 feet

Storage Conditions

Temperature
Humidity
Altitude

-40o F to +140o F (-40o C to +60o C)
5% to 95% (no condensation)
To 50,000 feet

Dimensions

Physical
(monitor)

360 mm(W) x 375 mm(H) x 395 mm (D)

14.2” (W) x 14.8” (H) x 15.6” (D)

Weight

Net 12.5 kg (27.6 lb) (monitor only)

Regulations

MPR II
UL/cUL, FCC-B, DHHS, ICES-B, NOM, Tuv-S

Power Saving Modes

On
Active Off

< NORMAL (Green LED)
< 3W (Yellow LED)

Preset Timing Modes

Recommended Timing Mode for this monitor is : VESA® 800 x600@75Hz

VGA 640 x 400 @ 70 Hz
VESA 640 x 480 @ 60, 75, 85 Hz
VESA 800 x 600 @ 72, 75, 85 Hz

VESA 1024 x 768 @ 60 H
Macintosh® 640 x 480 @ 67 H
Macintosh 832 x 624 @ 75 H

1. Macintosh models prior to G3 require a Macintosh adapter. To order a Macintosh adapter, contact ViewSonic
Customer Support. You will need to provide serial number of the product.

2. Warning:Do NOT set the graphics card in your computer to exceed these Maximum Refresh Rates; doing so could
result in permanent damage to the monitor.

Other Information

Specifications

CRT Type

Phosphor
Glass suface

15”(13.8” viewable diagonal area).

0.24 mm Horizontal, 0.14 mm Vertical, and 0.28 mm
diagonal dot pitch, 90o deflection

RGB, medim-short persistence
Anti-glare, anti-static coating
Standard light transmission rate = 57%

Input Signal Video

Sync

RGB Analog (0.7/1.0 Vp-p, 75 Ohms)
fH:30-54 kHz, fv:50-120 Hz
H/V Separate (TTL), Composite

Compatibility PC

Macintosh

1

VGA up to 1024 x 768 Non-interlaced
Power Macintosh (up to 832 x 624)

Timing Modes
(with Maximum Refresh Rates)2

1024 x 768 @ 70 Hz
800 x 600 @ 89 Hz
640 x 480 @ 110 Hz

Power Voltage AC 100-240 (auto switch) 50/60 Hz

Display Area Default

Full scan

266 mm(W) x 200 mm(V) (Typical)
284 mm(W) x 213 mm(V) (Depends on signal timing)

Operating Conditions Temperature

Humidity
Altitude

32o F to 104o F (0o C to +40o C)
5% to 95% (no condensation)
To 10,000 feet

Storage Conditions Temperature

Humidity
Altitude

-40o F to +140o F (-40o C to +60o C)
5% to 95% (no condensation)
To 50,000 feet

Dimensions Physical

(monitor)

360 mm (W) x 375 mm (H) x 395 mm (D)

14.2” (W) x 14.8” (H) x 15.6” (D)

Weight Net 12.5 kg / 27.6 lb (monitor only)

Regulations MPR II

UL/cUL, FCC-B, DHHS, ICES-B, NOM, Tuv-S

Power Saving Modes On

Active Off

< NORMAL (Green LED)
< 3W (Yellow LED)

Preset Timing Modes

Recommended Timing Mode for this monitor is : VESA® 800 x600@75Hz

VGA 640 x 400 @ 70 Hz
VESA 640 x 480 @ 60, 75, 85 Hz
VESA 800 x 600 @ 72, 75, 85 Hz

VESA 1024 x 768 @ 60 H
Macintosh® 640 x 480 @ 67 H
Macintosh 832 x 624 @ 75 H

1. Macintosh models prior to G3 require a Macintosh adapter. To order a Macintosh adapter, contact ViewSonic
Customer Support. You will need to provide serial number of the product.

2. Warning:Do NOT set the graphics card in your computer to exceed these Maximum Refresh Rates; doing so could
result in permanent damage to the monitor.

ViewSonic Q51 10

ViewSonic Q51 11

Cusomer Support

For technical support or product service, see the table below or contact your reseller.

NOTE: You will need the product serial number.

Country/

Region

Web Site

T=Telephone

F=Fax

E-mail

United States www.viewsonic.com/support

T:[phone]

F:[phone]

[e-mail]

Canada www.viewsonic.com/support

T:[phone]

F:[phone]

[e-mail]

United Kingdom www.viewsoniceurope.com

T: 0800 833 648

F:[phone]

service.eu@viewsoniceurope.

com

Europe, Middle

East, Baltic

countries, and

North Africa

www.viewsoniceurope.com

Contact your reseller

service.eu@viewsoniceurope.

com

Ausralia and New

Zealand

www.viewsonic.com.au

T:(61) 2 9906-6277

F:(61) 2 9906-6377

[e-mail]

Singapore/

Malaysia/Thailand

www.viewsonic.com.sg

T:(65) 273-4018

F:(65) 273-1566

[e-mail]

South Africa/Other

countries

www.viewsonic.com

T:(886) 2 2246-3456

F: (886) 2 8242-3668

[e-mail]

Hong Kong www.viewsonic.com

T:(886) 2 2246-3456

F: (886) 2 8242-3668

[e-mail]

ViewSonic Q5112

ViewSonic Q51 13

ViewSonic Q5114

Limited Warranty

ViewSonic CRT Monitors

What the warranty covers:

ViewSonic® warrants its products to be free from defects in material and workmanship,
under normal use, during the warranty period. If a product proves to be defective in material
or workmanship during the warranty period, ViewSonic will at its sole option repair or replace
the product with a like product. Replacement product or parts may include remanufactured or
refurbished parts or components.

How long the warranty is effective:

ViewSonic Monitor products are warranted for twelve (12) months for parts, and twelve (12)
months for labor.

Who the warranty protects:

This warranty is valid only for the first consumer purchaser. For rental units the warranty
commences upon the date the product is first put in use.

What the warranty does not cover:

1. Any product on which the serial number has been defaced, modified or removed.

2. If this product was purchased from an unauthorized reseller, there are no warranties,

express or implied, including the implied warranty of merchantability and the implied
warranty of fitness for a particular purpose and this product is sold strictly “as is” and “with
all faults”.

3. Damage, deterioration or malfunction resulting from:
a. Accident, misuse, neglect, fire, water, lightning, or other acts of nature,

unauthorized product modification, or failure to follow instructions supplied with

the product.
b. Repair or attempted repair by anyone not authorized by ViewSonic.
c. Any damage of the product due to shipment.

d. Removal or installation of the product.
e. Causes external to the product, such as electric power fluctuations or failure.
f. Use of supplies or parts not meeting ViewSonic’s specifications.
g. Normal wear and tear.
h. Damage caused by static (non-moving) images displayed for lengthy periods of

time (also referred to as “burn-in”).

i.

Any other cause which does not relate to a product defect.

4. Removal, installation, transportation, insurance, and set-up service charges.

How to get service:

1. For information about receiving service under warranty, contact ViewSonic Customer

Support at 800-888-8583. You will need to provide your product’s serial number.

2. To obtain warranted service, you will be required to provide (a) the original dated sales
slip, (b) your name, (c) your address, (d) a description of the problem, and (e) the serial

number of the product.

3. Take or ship the product freight prepaid in the original container to an authorized
ViewSonic service center or ViewSonic.

4. For additional information or the name of the nearest ViewSonic service center, contact
ViewSonic. Limitation of implied warranties:

There are no warranties, express or implied, which extend beyond the description contained
herein including the implied warranty of merchantability and fitness for a particular purpose.

Exclusion of damages:

ViewSonic’s liability is limited to the cost of repair or replacement of the product. ViewSonic
shall not be liable for:

1. Damage to other property caused by any defects in the product, damages based
upon inconvenience, loss of use of the product, loss of time, loss of profits, loss of
business opportunity, loss of goodwill, interference with business relationships, or other
commercial loss, even if advised of the possibility of such damages.

2. Any other damages, whether incidental, consequential or otherwise.

3. Any claim against the customer by any other party.

Effect of state law:

This warranty gives you specific legal rights, and you may also have other rights which vary
from state to state. Some states do not allow limitations on implied warranties and/or do not
allow the exclusion of incidental or consequential damages, so the above limitations and
exclusions may not apply to you.

Sales outside the U.S.A. and Canada:

For warranty information and service on ViewSonic products sold outside of the U.S.A. and
Canada, contact ViewSonic or your local ViewSonic dealer.

ViewSonic Q5115

ViewSonic

®