ViewSonic E70FSB-2 - E 70F+SB - 17"" CRT Display, E70f-5, E70fB-5, E70fSB-5, VCDTS22355-5 Service Manual

Service Manual

ViewSonic E70f-5

E70fB-5

E70fSB-5

Model No. VCDTS22355-5

17” Digital Controlled Color Monitor

(E70f-5_E70fB-5_E70fSB-5_SM Rev. 1c Dec. 2005)

ViewSonic® 381 Brea Canyon Road, Walnut, California 91789 USA - (800) 888-8583

2004 by ViewSonic Corporation. All rights reserved. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language or computer language, in any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise, without the prior written permission of ViewSonic Corporation.

Disclaimer

ViewSonic makes no representations or warranties, either expressed or implied, with respect to the contents hereof and specifically disclaims any warranty of merchantability or fitness for any particular purpose. Further, ViewSonic reserves the right to revise this publication and to make changes from time to time in the contents hereof without obligation of ViewSonic to notify any person of such revision or changes.

Revision History

Revision Date Description Of Changes Approval

1a 04/09/03 Initial Release DCN- 3105 Fellen Fan

Trademarks

ViewSonic is a registered trademark of ViewSonic Corporation. All other trademarks used within this document are the property of their respective owners.

Optiquest is a registered trademark of ViewSonic Corporation.

1b 09/06/04 Chassis updated DCN-4481 Angela Lu 1c 12/27/ 05 Add model of E70fSB-5 Sophia Kao

ViewSonic Corporation Confidential – Do Not Copy E70f-5_E70fB-5_E70fSB-5

TABLE OF CONTENTS

2. Specification

3. Front Panel Function Control Description

4. Circuit Description

6. Trouble Shooting Flow Chart

9. Block Diagram

10. Schematic Diagrams

7. Recommended Spare Parts List

1. Precautions and Safety Notices

5. Adjusting Procedure

8. Exploded Diagram And Spare Parts List

11. PCB Layout Diagrams

1 2

10 13 16

23 86

91 97

ViewSonic Corporation Confidential – Do Not Copy E70f-5_E70fB-5_E70fSB-5

WARNING!

This service information is designed for experience repair technicians only and is not designed for use by the general public.

It does not contain warnings or cautions to advise non-technical individuals of potential dangers in attempting to service

a product.

Products powered by electricity should be serviced or repaired only by experienced professional technicians. Any attempt to service or repair the product or products dealt within this service information by anyone else could result in serious injury or death.

1. CAUTION

No modification of any circuit should be attempted. Service work should only be performed after you are thoroughly familiar with all of the following safety checks and servicing guide lines.

2. SAFETY CHECK

Care should be taken while servicing this CRT display because of the high voltage used in the deflection circuits. These voltages are exposed in such areas as the associated flyback and yoke circuits.

3. FIRE & SHOCK HAZARD

3-1 Insert an isolation transformer between the CRT display and AC power line before servicing the chassis. 3-2 In servicing pay attention to original lead dress especially in the high voltage circuit. If a short circuit is found,

replace all parts which have been overheated as a result of the short circuit. 3-3 All the protective devices munt be reinstalled per original design. 3-4 Soldering must be inspected for possible cold solder joints, frayed leads, damaged insulation, solder splashes or

sharp solder points. Be certain to remove all foreign material.

4. LEAKAGE CURRENT COLD CHECK

4-1 Unplug the AC cord and connect a jumper between the two prongs on the plug. 4-2 Turn the CRT display power switch “on”. 4-3 Measure the resistance value with an ohmmeter between the jumpered AC plug and each exposed metallic part

on the CRT display such as the metal frame, screwheads, control shafts, etc. When the exposed metallic part has

a return path to the chassis, the reading should be 1.8 megohm minimum.

5. LEAKAGE CURRENT HOT CHECK

5-1 Plug the AC cord directly into the AC outlet. Do not use an isolation transformer during this check. 5-2 Connect a 1500 ohm, 10 watt resistor, paralleled by a 0.15uF capacitor between each exposed metallic part and

a good earth ground (as shown in Fig.1). 5-3 Use an AC voltmeter with 1000 ohm/volt or more sensitivity and measure the AC voltage across the

combination 1500 ohm resistor and 0.15uF capacitor.

1. Precautions And Safety Notices

ViewSonic Corporation Confidential – Do Not Copy E70f-5_E70fB-5_E70fSB-5

5-4 Move the resistor connection to each exposed metallic part and measure the voltage. 5-5 Reverse the polarity of the AC plug in the AC outlet and repeat the above measurement. 5-6 Voltage measured must not exceed 7.5 volt RMS, from any exposed metallic part to ground A leakage current

tester may be used in the above hot check, in which case any current measured must not exceed 5.0 milliamp. In the case of a measurement exceeding the 5.0 milliamp value, a rework is required to eliminate the chance of shock hazard.

Note： High voltage is present when this CRT display is operating. Always discharge the anode of the picture

tube to the display chassis to prevent shock hazard.

AC VOLTMETER

TO INSTRUMENT'S EXPOSED METAL PARTS

1500 Ω 10W

0.15μF

Fig. 1

(EARTH GROUND)

6. IMPLOSION PROTECTION

Picture tubes are equipped with an integral implosion protection system, but care should be taken to avoid damage and scratching during installation. Use only Panasonic replacement picture tubes.

7. X-RADIATION

WARNING：The only potential source of X-Radiation is the picture tube. However when the high voltage circuit is operating properly there is no possibility of X-Radiation problem. The basic precaution whic h must be exercised is to keep the high voltage at the following factory-recommended level.

Note：：：： It is important to use an accurate periodically calibrated high voltage meter.

7-1 The procedure for adjusting high voltage is shown on page 13. 7-2 If can not be adjust 25.0 KV at immediate service is required to prevent the possibility of premature

component failure.

7-3 To prevent X-Radiation possibility it is essential to use the specified picture tube.

IMPORTANT SAFETY NOTICE

There are special components used in this CRT displays which are important for safety. These parts are identified

by the international symbol

on the schematic diagram and on the replacement parts list. It is essential that these critical parts should be replaced with manufacture’s specified parts to prevent X-RADIATION, shock, fire, or other hazards. Do not modify the original design or this will void the original parts and labor guarantee.

ViewSonic Corporation Confidential – Do Not Copy E70f-5_E70fB-5_E70fSB-5

1. CRT : 43.2CM(17") 90 Deflection, 29mm Neck, 0.27mm Dot Pitch, Non-Glare Screen

2. Viewable image Size: 40.6CM (16") diagonal

3. Display Color: Unlimited Colors

4. External Controls: Power On/Off, OSD key, Function knob: Contrast, Brightness, Degauss, H-Size, H-Center, V-Center, V-Size, ZOOM, Pincushion, Trapezoid, Pin-Balance, Parallelogram, Rotation, Color Temperature, H-Moire Reduce, V-Morie, Memory Recall, Language, ViewMeter. OSD position select

5. Input Video Signal

Mode

1 2 3 4 5 6 7 8 9 10 11 12 Horizontal Freq. (KHz) 31.47 31.47 37.5 43.27 46.87 53.67 60.02 68.67 63.98 35.000 832*624 1024*768

Dot Clock (MHz) 25.18 28.18 31.5 36 49.5 56.25 78.75 94.5 108 30.240 57.283 80.000

Horizontal Lines 720

640 800 1024 1280 640 832 1024

Vertical Lines 400

480 600 768 1024 480 624 768 H. Sync Polarity NEG NEG NEG NEG POS POS POS POS Pos NEG NEG NEG

H. Period (µs) 31.78 31.78 26.67 23.11 21.333 18.63 16.66 14.56 15.63 28.571 20.111 16.600

H. Sync Width (µs) 3.18 3.81 2.03 1.56 1.616 1.138 1.219 1.016 1.037 2.116 1.117 1.200

H. Back Porch (µs) 1.96 1.589 3.81 2.22 3.232 2.702 2.235 2.201 2.296 3.175 3.910 2.200

H. Active (µs) 25.42 25.42 20.32 17.78 16.162 14.22 13 10.83 11.85 21.164 14.524 12.800

Vertical Freq. (Hz) 69.93 59.94 75 85.01 75 85.06 75.02 84.99 60.02 66.667 75.550 74.927

V. Sync Polarity POS NEG NEG NEG POS POS POS POS Pos NEG NEG NEG

V. Period (ms) 14.3 16.68 13.33 11.76 13.333 11.75 13.32 11.76 16.66 15.000 13.414 13.346

V. Sync Width (ms) 0.06 0.06 0.08 0.07 0.064 0.056 0.05 0.044 0.047 0.086 0.060 0.050

V. Back Porch (ms) 1.14 0.79 0.43 0.58 0.448 0.503 0.466 0.524 0.594 1.114 0.784 0.498

V. Active (ms) 12.71 15.25 12.8 11.09 12.8 11.17 12.79 11.18 16 13.714 12.549 12.749

Standard VGA VGA VESA VESA VESA VESA VESA VESA VESA MAC MAC MAC

6. Display Size Horizontal: 310 mm +/-4mm Vertical: 230 mm +/-4mm

7. Scanning Frequencies Horizontal:

30KHz ~ 70KHz

Vertical:

50 Hz ~ 160 Hz

8. Factory Preset Timings: 12 User Timings: 20

9. Misconvergence A Zone: 0.25 mm Max. B Zone: 0.30 mm Max. C Zone 0.35 mm Max

2. Specification

ViewSonic Corporation Confidential – Do Not Copy E70f-5_E70fB-5_E70fSB-5

10. Video Bandwidth: 120 MHz

11. Power Source: Switching Mode Power Supply AC 100 ~240V, 50/60Hz Universal Type

12. Operating Temperature: 0°C to 40°C Ambient

13. Humidity: 5% to 95% Relative, Non-Condensing

14. Weight: 15. Kgs(Net), 17.5Kgs(Gross)

15. Package Specifications Width: 410 mm Height: 355 mm Depth: 420mm

16. External Connection: 15 Pin D-sub Connector AC Power Cord

17. Regulatiory/Safety

Regulatory Filing Regulatory filing should be made under the “Model Number-

XY”

Pacific Asia Australia, New Zealand, So. Africa

UL1950, c UL1950,FCC Part 15 Subpart J Subpart B, DHHS Part 21 Subpart J X-Ray Protection, CSA 22.2/cUL950, ICES003 Class B, CB, CE, MSMI, PSB, C-TICK, EPA Energy Star, VCC I

Europe UL1950, FCC Part 15 Subpart J Subpart B, DHHS Part 21

Subpart J X-Ray Protection, CSA 22.2/cUL950, ICES-003 Class B, CB, EMC/CE, TUV/GS, NEMKO, SEMKO, DEMKO, FIMKO, Gost-R, PCBC, SASO, Energy Star

15.2 International

CB, MPRII, CE

15.3 Power Management

Power Management Amendment to EnergyStar Version 2

MOU, dated

ViewSonic Corporation Confidential – Do Not Copy E70f-5_E70fB-5_E70fSB-5

OPERATING INSTRUCTIONS

This procedure gives you instructions for installing and using the Color display.

1. Position the display on the desired operation and plug the power cord into a convenient AC outlet. Threewire power cord must be shielded and is provided as a safety precaution as it connects the chassis and cabinet to the electrical conduit ground. If the AC outlet in your location does not have provisions for the grounded type plug, the installer should attach the proper adapter to ensure a safe ground potential.

2. Connect the 15-pin color display shielded signal cable to your signal system device and lock both screws on the connector to ensure firm grounding. The connector information is as follow:

15 - Pin Color Display Signal Cable

PIN NO.

DESCRIPTION

PIN NO.

DESCRIPTION

1. RED 9. 5V From PC

2. GREEN 10. Sync GND

3. BLUE 11. NC

4. GND 12. SDA

5. GND 13. HORIZ. SYNC

6. GND-R 14.

VERT. SYNC (＊VCLK)

7. GND-G 15. SCL (DDC CLOCK)

8. GND-B

3. Apply power to the display by turning the power switch to the "ON" position and allow about thirty seconds for display tube warm-up. The Power-On indicator lights when the display is on.

4. With proper signals feed to the display, a pattern or data should appear on the screen, adjust the brightness and contrast to the most pleasing display.

5. This monitor has power saving function following the VESA DPMS. Be sure to connect the signal cable to the PC.

6. If your color display requires service, it must be returned with the power cord.

11 15

ViewSonic Corporation Confidential – Do Not Copy E70f-5_E70fB-5_E70fSB-5

Adjusting the Screen Image

Use the buttons on the front control panel to display and adjust the OnView

controls which display on the screen. The OnView controls are explained at the top of the next page and are defined in “Main Menu Controls” on page 8.

Main Menu With OnView controls

Front Control Panel

Displays Main Menu; also saves changes/exits Main Menu

Power Light

Power On/Off

Scroll through menu Displays control screen for

highlighted control (or pair of controls). Also, toggles between pairs of controls on some control screens

options and adjust the displayed control

Memory Recall

returns adjustments to

the original factory settings if the display is operating in a factory preset

timing mode listed in this user guide.

Exception: This control does not affect changes made with the User Color control.

3. Front Panel Function Control Description

ViewSonic Corporation Confidential – Do Not Copy E70f-5_E70fB-5_E70fSB-5

Do the following to adjust the screen image:

To display the Main Menu, press button [1].

To select a control you want to adjust, press the arrow buttons on the front control panel of your monitor and scroll through the choices. When the control you want is highlighted, press button [2].

NOTE: Some controls on the Main Menu are listed in pairs, such as Contrast/Brightness. Display control screen (sample shown in step 3 below). Press button [2] to toggle to the next control in the pair.

To adjust the selected control, such as

CONTRAST

in the sample below,

press the arrow buttons.

To save the control setting and Exit the menu press button [1] twice.

BRIGHTNESS

OSD Lock Settings

You have the option of using the On Screen Display (OSD) locking feature, OSD LOCK, to prevent unwanted changes to the current image settings.

• OSD Lock: Press and hold the [1] and [

▼]

buttons on the face of the monitor for 10 seconds. The message "OSD LOCK" will then display briefly, indicating that the OSD image settings are now locked.

• OSD Unlock: Press and hold the [1] and [

▼]

buttons again for 10 seconds. The message "OSD UNLOCK" will then display briefly, indicating that the OSD image settings are now unlocked.

ViewSonic Corporation Confidential – Do Not Copy E70f-5_E70fB-5_E70fSB-5

Main Menu Controls

Adjust the menu items shown below by using the up and down buttons.

Control Explanation

Contrast

adjusts the difference between the image

background (black level) and the foreground (white level).

Brightness

adjusts the background black level of the screen

image.

Zoom

expands and contracts the entire screen image.

Horizontal Position

moves the screen image left or right.

Horizontal Size

adjusts width of the screen image.

Vertical Position

moves the screen image up or down.

Vertical Size

adjusts the height of the screen image.

Pincushion

curves the vertical sides of the screen image.

Pin Balance

curves the vertical edges of the screen image to

the left or right.

Trapezoid

adjusts the top and bottom of the screen image

until they have equal length.

Parallel

slants the vertical edges of the screen image until

they are parallel.

Tilt

rotates the entire screen image.

ViewSonic Corporation Confidential – Do Not Copy E70f-5_E70fB-5_E70fSB-5

Degauss

removes the build-up of magnetic fields that can cause irregular colors to appear around the edges of screen images. There are two ways to degauss the display: automatically by turning the monitor on, or manually by selecting the Degauss control from the menu.

With Degauss selected from the menu, press button [2] to degauss the monitor manually.

Important: Do not degauss repeatedly. Doing so can be harmful to the display. Wait at least 20 minutes (before

selecting this control again.

ViewMatch® Color provides several color options: several

preset color temperatures and User Color which allows you to adjust red (R), green (G), and blue (B). The factory setting for this product is 9300K (9300°Kelvin).

9300K

— Adds blue to the screen image for cooler white

(used in most office settings with fluorescent lighting).

6500K

— Adds red to the screen image for warmer white

and richer red.

5000K

— Adds blue and green to the screen image for a

darker color.

User Color

— Individual adjustments for red, green, and

blue.

Moire reduces interference patterns that appear as ripples,

waves, or unwanted background color textures. Interference patterns of this type are most noticeable when viewing images having closely spaced lines or finely detailed patterns.

Language allows you to choose from among several

languages for the menus and control screens: English, French, German, Italian, and Spanish.

Memory Recall returns adjustments to the original factory

settings if the display is operating in a factory preset timing mode listed in this user guide.

Exception: This control does not affect changes made with the User Color control.

ViewMeter

displays the frequencies (horizontal and

vertical) coming from the graphics card of the computer.

Control Explanation

OSD Position

allows you to move the on-screen display

menus and control screens.

ViewSonic Corporation Confidential – Do Not Copy E70f-5_E70fB-5_E70fSB-5

4-1 MICRO CONTROLLER CIRCUIT

MICRO Controller

The IC101 contains a 8031 8-bit CPU core, 60K bytes of RAM, 16K bytes of ROM,14 channel 8 bit PWM D/A converters, 2 channel A/D converters for key detection,0.5sec watch-dog timer, internal H-sync and V-sync signals processor providing mode detection, watch- dog timer preventing system from abnormal operation, and an I²C bus interface.

H/V sync signals processor

The functions of the sync processor include polarity detection, H-SYNC & V-SYNC signals counting, Programmable SYNC signals output, free running signal generator. Pin41/Pin42 are for the H-SYNC and VSYNC input, Pin34/Pin33 will output the same signal as input sync signal without delay, and the polarity are setting in the positive. When no signal input, the Pin32 will output a 60Hz V-SYNC free run signal. The Pin33 will output a 48KHz H-SYNC free run signal. for the monitor testing use.

On Screen Display Controller

The IC801 is designed for display the built-in characters or fonts onto monitor screen. The display operation is by transforming data and control information from micro controller to RAM through a serial data interface. Pin2 is used to control the internal oscillator frequency by DC voltage input from external low pass filter (R154, C166, R155) and filter (R175, C167) is used to regulate the appropriate bias current for internal oscillator the resonate at specific dot frequency. Pin5 is input the horizontal fly back pulse, for PLL generator tracking. Pin6 is left floating, I²C bus is enabled. Otherwise the SPI bus is enabled. Pin7 the external data transfer through this pin to internal display registers and control registers Pin8 the clock-input pin is used to synchronize the data transfer. Pin10 is input the vertical flyback pulse for synchronizing the vertical position. Pin12 is output a blanking signal to cut off external R.G.B signals of VGA while this chip is displaying characters or windows. Pin13, Pin14, Pin15 is used to output the OSD (B.G.R) video signal.

4. Circuit Description

ViewSonic Corporation Confidential – Do Not Copy E70f-5_E70fB-5_E70fSB-5

4-2 DEFLECTION CIRCUIT

The deflection circuit is achieved by a high performance and efficient solution IC 401 (TDA4841) for this monitor. The concept is fully DC controllable and can be used in applications with a micro-controller solutions. The TDA4841 provides sync. Processing with full auto sync. Capability, a flexible SMPS block and an extensive set of geometry control facilities. Further the IC generates the drive waveforms for DC coupled vertical boosters to the TDA4863.

Horizontal Oscillator

The oscillator is of the relaxation type and requires a capacitor of 1nF C403 at pin29.

PLL 1 Phase Detector

The phase detector is a standard one using switched current sources. It compares the middle of H-sync. with a fixed point on the oscillator saw-tooth voltage. The PLL loop filter C401, C402, R409 is connected to Pin26.

PLL2 Phase Detector

The PLL2 detector thus compensates for the delay in the external H-deflection circuit by adjusting the phase of the HDRV output pulses. The phase between H-flyback and H-sync can be controlled at pin30.

X-ray Protection

The X-ray protection input pin2 provides a voltage detector with a precise threshold. If the voltage exceeds this threshold for a certain time, an internal latch switches the whole IC into protection mode. In this mode several pins are forced into defined states: Pin6 (BDRV) is floating Pin8 (HDRV) is floating Pin12, 13 ( VOUT 12, 13) are floating

Vertical Oscillator

The vertical free –running frequency is determined by the resistor C613 at pin24. Usually the free-running frequency should be lower than the minimum trigger frequency.

ViewSonic Corporation Confidential – Do Not Copy E70f-5_E70fB-5_E70fSB-5

4-3 TRANSISTOR & DIODE CIRCUIT

LOCATION

CIRCUIT FUNCTION DESCRIPTION

D901 ~ D904 Bridge Rectifier for AC Source D910 Clamp Diode for Snubber CKT D918, D919 Rectifier for Output Voltage D922 Rectifier for Output Voltage D923 Rectifier for Output Voltage D925 Rectifier for B+ Supply Q901 MOS FET for Switching Power Control. Q907, Q908 Use for Off-Mode to Cut-off 6.3V Supply Voltage Q909, Q918 Use for Standy-By or Suspend Mode to Cut-off 12V Supply Voltage Q912, Q920 Push-Pull Topology to Drive Q911 Q913 Degaussing Switcher Transistor Q921 5V Regulator Transistor Q701 Turn-on at Power ON/OFF and Change Mode to Protect Hor.Block Q402 HOR. Driver Transistor Q426 Horizontal s correction control MOSFET Q404, Q405 As Differential Amp. to Drive Q406 Q406 Transistor for H-Size Control Q705 Brightness Control CKT

ViewSonic Corporation Confidential – Do Not Copy E70f-5_E70fB-5_E70fSB-5

5-1 ADJUSTMENT CONDITIONS AND PRECAUTIONS

1. Approximately 30 minutes should be allowed for warm up before proceeding.

2. Adjustments should be undertaken only on those necessary elements since most of them have been carefully preset at the factory.

5-2 MAIN ADJUSTMENTS

NO.

FUNCTION LOCATION DESIGNATION

1. 14V ADJ PCB - MAIN VR903

2. B + ADJ PCB - MAIN VR902

3. SCREEN ADJ FLY BACK TRANS T402 SCREEN VR

4. FOCUS ADJ FLY BACK TRANS

T402 FOCUS

VR1&VR2

5. ABL ADJ PCB - MAIN AB in factory OSD

6. FUNCTION ADJ -MENU PCB - MAIN <SW104>

-UP

PCB - MAIN SW104

-DOWN

PCB - MAIN <SW103>

-EXIT PCB - MAIN SW103

-RECALL PCB - MAIN (SW103)

5-3 ADJUSTMENT METHOD

1. 14V, B + & HV voltage adjustment:

A. Chroma-2000 Signal generator or PC equivalent set mode 1, VGA 640X480 pattern 1.0. B. Connect a DC Volt meter between TP901 and ground, then adjust VR903to be 14VDC. C. Connect a DC Volt meter between TP902 and ground, then adjust VR902 to be 64 VDC.

2. Factory preset Timings Adjustment:

A. Press

Key to show OSD window press Up or Down Key to switch the functional controls.

B. Press the Up Key to select the "ZOOM" function, then press the MENU Key. While do not release the

MENU Key until the OSD window changed to the Factory preset window.

C. The Factory preset window contains the following functional controls. Select one of the control. Then

press the Up/Down Key to adjust its value for the optimum picture.

5. Adjusting Procedure

ViewSonic Corporation Confidential – Do Not Copy E70f-5_E70fB-5_E70fSB-5

CONTRAST

H-MOIRE REDUCE

BRIGHTNESS

V-MOIRE REDUCE

H-CENTER

R-GAIN

H-SIZE

G-GAIN

V-CENTER

B-GAIN

V-SIZE

R-BIAS

ZOOM

G-BIAS

PINCUSHION

R-BIAS

TRAPEZOID

9300

COLOR TEMPERATURE

PIN-BALANCE

6500

COLOR TEMPERATURE

PARALLELOGRAM

5500

COLOR TEMPERATURE

ROTATION

OSD EXIT

V-LINEARITY

RETURN

V-LINEARITY

H-size Max range limit.

ABL CORTROL

Operation time record.

TOP CORNER

BURN IN

BOTTOM CORNER

DEGAUSS

D. To switches the input signal to the other Timing Mode. Please follow step A ~ C to get the optimum

picture.

E. Select the "

" RETURN function and press the MENU Key, then the Factor Preset window will

be returned to the original OSD window.(user's operating condition)

F. The setting data of the CONTRAST, BRIGHTNESS, PIN-BALANCE, PARALLELOGRAM,

ROTATION, COLOR TEMPERATURE are common mode saved in the memory. Don't needed adjust it individual at every timing Mode and save in the memory.

3. White Balance, Luminance adjustment: A. Bias (Low Luminance) adjustment:

(a) Set mode 1024*768 Fv: 85Hz full white pattern. (b) To make the adjustment condition is under the Factory preset window.

Same as step 2-B.

set to maximum. Contrast set to maximum. full raster pattern,

(e) Fixup G-Bias(DAC=30)

, adjust B-Bias , R-Bias , then adjust FBT screen VR

to make x= 283 ± 10, y= 298 ± 10 Y= 3.5+

2cd/m² Brightness set to raster just cutoff(0.05cd/ m²),

to save to color temperature 9300k .

B. Gain (High light) adjustment:

(a) Set mode 1024*768 Fv: 85Hz

20% of default image pattern.

(b) Brightness set to raster just cutoff and set the contrast to max. (c) Adjust G-Gain

, B-Gain , R-Gain , to make color temperature x=283 ± 10,

y=298 ± 10. Y=155±10cd/m².

ViewSonic Corporation Confidential – Do Not Copy E70f-5_E70fB-5_E70fSB-5

C. The adjustment of 6500°K white Balance, May follow step A ~ B , with the x=313 ± 10, y=329 ±

10.Y=145±10cd/m²

D. Thr adjustment of 5000°K white Balance, May follow step A-B, with the x=346± 10, y=359 ± 10,

Y=135±10cd/m²

E. Full white luminance:

(a) Set mode1 1024*768 Fv: 85Hz full white pattern. (b) Image Size : H:310±4mm V:230±4mm. (c) Brightness set to raster just cut off and set the contrast to max.

(d) Adjust AB(

) to the luminance at 105± 10cd/m².

4. Focus Adjustment: A. Set mode 1024×768 Fv: 85Hz with character full page. B. Adjust brightness to center and contrast to max. C. Then adjust focus VR1 to a fine vertical line. D. Adjust focus VR2 to a fine horizontal line. E. Repeat step C & D.

5. Purity Adjustment A. Be sure that the display is not being exposed to any external magnetic fields. B. Ensure that the spacing between the Purity, Convergence, Magnet, (PCM), assembly and the CRT stem is

29mm. (See below diagram)

C. Produce a complete, red pattern on the display. Adjust the purity magnet rings on the PCM assembly to

obtain a complete field of the color red. This is done by moving the two tabs in such a manner that they advance in an opposite direction but at the same time to obtain the same angle between the two tabs, which should be approximately 180'.

D. Check the complete blue and complete green patterns to observe their respective color purity. Make minor

adjustments if needed.

RELATIVE PLACEMENT OF TYPICAL COMPONENTS

Purity Magnets

Deflection Yoke

4-pole Convergence Magnets

6-pole Convergence Magnets

6. Convergence adjustment A. Produce a magenta crosshatch on the display.

B. Adjust the focus for the best overall focus on the display.

Also adjust the brightness to the desired condition.

C. Vertical red and blue lines are converged by varying the angle between the two tabs of the 4 pole magnets

on the PCM assembly. (See above diagrams)

D. Horizontal red and blue lines are converged by varying the two tabs together, keeping the angle between

them constant.

E. Produce a white crosshatch pattern on the display. F. Vertical green and magenta lines are converged by varying the angle between the two tabs of the 6-pole

magnets.

G. Horizontal green and magenta lines are converged by varying the two tabs together, keeping the angle

between them constant.

ViewSonic Corporation Confidential – Do Not Copy E70f-5_E70fB-5_E70fSB-5

6-1 NO RASTER, CRT RELATIVE CIRCUIT PROBLEMS

REFER ITEM S.M.P.S.

BRIGHTNESS SET TO MAX.

CHECK CRT G1 VOLTAGE

NG NG

NG NG OK OK

OK OK OK

CHECK THE HIGE

CHECK THE VOLTAGE OF

HEATER A

BOUT 6.3V

CHECK VOLTAGE OF THE

CHECK BRIGHTNESS

CHECK POWER SAVING

"ABNORMAL

SYNC, V

SYNC

CHECK SCREEN VOLTAGE

LESS THAN 300V

CHECK FBT

CHECK MAIN PCB POWER

CHECK FAILSAFE CKT

Q909,

CHECK CRT'S HEATER

CIRCUIT Q907,

Q705 RELATIVE CKT.

PIN 25 RELATIVE CKT.

OF CRT ABOUT 25.5 ~

400V TO 600V

REFER ITEM 6

-2

53V, 14V, 80V

CATHODE ABOUT 65V TO

CHECK MAIN PCB POWER SUPPLY 57.5V,14V,80V

CHECK THE HIGE VOLTAGE OF CRT ABOUT 24.5~26.5KV

CHECK BRIGHTNESS CIRCUIT Q705 RELATIVE CKT.

6. Trouble Shooting Flow Chart

ViewSonic Corporation Confidential – Do Not Copy E70f-5_E70fB-5_E70fSB-5

1.ABNORMAL VIDEO LEVEL ON SCREEN

NG OK

CHECK THE VOLTAGE OF IC801

CHECK THE SIGNAL INPUT OF

ABOUT 0.7Vpp

CHECK THE VIDEO OUTPUT OF

R.G.B. APPROACH

CHECK SIGNAL CABLE

INTERFACE

CARD.

CONTRAST SET

PIN 10 ABOUT 5V

CHECK 5V RELATIVE

CHECK THE IC801 PIN

RELATIVE CIRCUIT

CHECK IC801 PIN 23 CLAMP

PIN 19, 20, 21 ABOUT

CHECK IC801 PIN 5/PIN 6/PIN 7 & PIN

2. ABNORMAL DDC (PLUG & PLAY)

CHECK IC101 PIN 5 VOLTAGE ABOUT 5V

CHECK SIGNAL CABLE

CHECK Q921 GOOD OR FAIL

OR H802 PIN 2, 3 DATA OUTPUT

CHECK IC101 PIN 5 VOLTAGE ABOUT

OUTPUT

ViewSonic Corporation Confidential – Do Not Copy E70f-5_E70fB-5_E70fSB-5

6-2 ABNORMAL DISPLAY

1.NO SIGNAL ON SCREEN

CHECK FBT RELATIVE

LESS THAN 400V

OK NG NG

OK NG

CHECK THE OUTPUT VOLTAGE

CHECK THE B+ VOLTAGE OF

CHECK THE VOLTAGE OF

CATHODE ABOUT

CHECK T

CHECK THE RELATIVE

CHECK THE 12V PIN

OF SMPS ON MAIN

RELATIVE CIRCUIT

OF P802

ABOUT 400V TO

EXCEED 700V

CHECK FBT & CRT RELATIVE

CHECK VIDEO IC801 VCC ABOUT

OF IC801 PIN 19, 20, 21 AT

CHECK THE

OF IC801 PIN 10 Vcc CIRCUIT

OR REFER ITEM

VIDEO PCB ABOUT

CHECK THE 80V RELATIVE

ViewSonic Corporation Confidential – Do Not Copy E70f-5_E70fB-5_E70fSB-5

6-3 NO BLANKING

NG OK CHECK THE

CIRCUIT OF

CHECK THE RELATIVE

CHECK G1 RELATIVE

CHECK R859 ON VIDEO

FBT PIN 4 ON MAIN

OF Q601, Q707

6-4 HOR./OSC/DEF/HV CIRCUIT FAULT

1. NO RASTER (DISCONNECT WITH SIGNAL CABLE)

NG OK

OK OK NG NG NG

CHECK THE COLLECTOR

RELATIVE CIRCUIT

CHECK Q402,

CHECK T401, T402, Q402,

ABOUT 3Vpp

OF Q403 ABOUT 1200Vpp

D408, C418, C419, H

DY,

CHECK IC401 PIN 8 WAVE FORM

CHECK IC401 PIN 26~29,

CHECK IC401 PIN 10 ABOUT 12

CHECK IC401 PIN 10 RELATIVE

OF Q402 ABOUT

CHECK T401,T402,Q402,Q403,CD408,D408, C418,C419,H-DY,B+

Q705.

ViewSonic Corporation Confidential – Do Not Copy E70f-5_E70fB-5_E70fSB-5

6-5 ABNORMAL HORIZONTAL DEFLECTION

1. ABNORMAL HORIZONTAL WIDTH OF VIDEO

NG OK

CHECK THE RELATIVE

CHECK THE

CIRCUIT OF

READJUST H

WIDTH

OF Q404, Q405, &

CHECK THE HV

CHECK FBT B+

CRT ABOUT 25.5KV

ABOUT 65V AT

2. ABNORMAL HORIZONTAL VIDEO CENTER

RELATIVE CIRCUIT

CHECK IC401 PIN 29

3. ABNORMAL HORIZONTAL LINEARITY

CHECK L401, Q426, Q428,Q431

24.5KV

ViewSonic Corporation Confidential – Do Not Copy E70f-5_E70fB-5_E70fSB-5

6-6 ABNORMAL VERTICAL SCANNING

1. ABNORMAL VERTICAL SIZE

OK NG

READJUST V- SIZE FUNCTION

RELATIVE CIRCUIT

CHECK VERT. OSC

RELATIVE CIRCUIT

READJUST V-SIZE FUNCTION

CHECK THE VOLTAGE OF

RELATIVE CIRCUIT

CHECK IC401 PIN 12, 13, 21,

22,24

CHECK THE IC601 PIN 2 ABOUT 12V

PIN 4 ABOUT -12V

CHECK D601,

2. VERTICAL CENTER

READJUST V-CENTER

RELATIVE CKT

CHECK IC401 AND IC601

6-7 SIDE-PIN CUSHION DISTORTION

READJUST SIDEPIN

CHECK IC401, Q404, Q405, Q406 RELATIVE CKT.

6-8 POOR FOCUS

READJUST FOCUS CONTROL

CHECK FOCUS CONTROL UNIT,

FOCUS LEAD WIRE, CRT SOCKET & CRT

ViewSonic Corporation Confidential – Do Not Copy E70f-5_E70fB-5_E70fSB-5

6-9 POWER SUPPLY TROUBLE SHOOTING CHART

BEFORE CHECK SW.REG. PLEASE REFER TO THE POWER SUPPLY BLOCK DIAGRAM POWER SUPPLY OUTPUT: (A) VARIABLE OUTPUT : 58. V - 14V

(DEPENDING EPENDING UPON H.SYNC FREQUENCY) (B) CONSTANT OUTPUT : 6.3V, 12V, -12V, 80V

BEAD SET

ABNORMAL VARIABLE OUTPUT

NG OK

NG OK OK NG NG

OK OK

NG OK NG YES CHECK BRIDGE

RECTIFIED CIRCUIT

CHECK START C.K.T

CHECK D919

CHECK Q911

Q911 FAILURE

CHECK Q901

CHECK IC901

CHECK AC LINE VOLT 120V OR 220V

CHECKF901, SW901

CHECK LINE RECTIFIED & SMOOTHED VOLT

CHECK Q901

IC901 FAILURE

CHECK T901 O/P

MAKE SURE THAT

HE VARIABLE

Output is not shorted

R923 R924, D911, D917

6.3V, -12VCIRCUIT OUTPUT

IC401,10(ABOUT 11.5V)

R904, Q906

Check 78V,

9.5V, 14V

CHECK THE 53V

Check IC401 pin

3,4,5,6,B+driver

ViewSonic Corporation Confidential – Do Not Copy E70f-5_E70fB-5_E70fSB-5

Rev: 1c

Serial No. Prefix: PU4

Item ECR/ECN ViewSonic P/N Ref. P/N Location Universalnumber# Q'ty

Accessories:

POWER CORD (-5P/M)

A-00004583 89C420L18N IS 1PCS

CHASSIS FOR P773Z-1 VSC (-5P/M)

B-MB-0201-0707 CMP773Z1NVNL1 1PCS 3 CRT BOARD P773Z-1VSC B-VB-0202-0304 CRP773Z1NVW 1PCS 4 FRONT PANE

C-00004586 34C 985BF0 A 1PCS

5 BACK COVE

C-00004587 34C 739 F0 1A 1PCS

6 BASE C-00004588 34C 741 F0 L 1PCS

Cables:

SIGNAL CABL

CB-00004589 89C174L8ECBB2 1PCS

8 CD MANUAL (E70f-5P/EM

)

DC-00004665 70C 747709 1F 1PCS

9 CD MANUAL (E70f-5M

)

DC-00004591 70C 747709 1E 1PCS 10 Capacitor 220UF +-20% 400V HEC E-C-0405-4331 67C 3022114D C907 1PCS 11 CPT 17" RF TCO BT CRT E-00004668 750A5C15EAV E750A 1PCS 12 CRT COCKET(QQ FOCUS

)

E-00002860 87C3504 ZW

1PCS

13 DEGAUSSING COI

E-00004666 750A1697504JAG

1PCS 14 Diode 1N5408 PEC E-00002714 93C 5255P52T D901,D902,D903,D904 4PCS 15 Diode RG-4S E-00004342 93C30408AT D919 1PCS 16 DRIVER TRANSFORME

E-T-0408-0526 79C 167125 LS T401 1PCS 17 FBT E-00002863 79A 763 BG 7 T402 1PCS 18 FOUCS E-00002862 79C 167126 HA T403 1PCS 19 FUSE 4A 250V LF-618 004 E-00002695 84A 7H400 SL F901 1PCS 20 IC 24LC08B/PG E-00002694 56C1133 13 IC102 1PCS 21 IC A 8PIN IC UC3842AM/LI

E-00004550 56C 379 12 IC901 1PCS 22 IC Amplier IC:LM2465TA E-00002697 56C 551 524 IC802 1PCS 23 IC LM1246DKA/NA/NOP

E-IC-0401-4019 56C 366509 IC801 1PCS 24 IC LM2480NA/NOPB E-IC-0401-2060 56C 539 6 IC803 1PCS 25 IC NT6863U-60026 E-00004339 56A1125566 IC101 1PCS 26 IC TDA4841PS/PHILIPS E-00002873 56C 552 2 IC401 1PCS 27 IC TDA4863A/PHILIPS E-00002874 56C 584 1A IC601 1PCS 28 Inductor 150UH +-10% FOR TD

E-00002875 73C 253 69 T L405 1PCS

29 Inductor CHOC

E-00002876 73C 253 88 HB L906 1PCS

30 LINEARITY COI

E-00004592 73C 147 538 H L401 1PCS

31 Main Transforme

E-00002864 80AS763 1NFH T901 1PCS

TCR 15OHM+-15%2.5A THI E-00002858 61C 58 8T L

R901 1PCS 33 PTCR E-00002859 61C 52 27 4J PR901 1PCS 34 Transistor 2SC5929 E-00002865 57C 706505 Q403 1PCS 35 Transistor A TR.NPN TIP122/FAIRCHIL

E-00004340 57C 415 1 Q406 1PCS 36 Transistor CEPF630 BY CET E-Q-0402-7029 57A 600 14 Q426,Q428,Q431 3PCS 37 Transistor IRF634B E-Q-0402-1508 57C 600 27 Q911 1PCS 38 Transistor STP9NK70ZFP E-00002867 57C 724501 Q901 1PCS 39 SCREW 3.5X10 HW-00004197 B1C1035 10128 1PCS 40 SCREW 4X7(FOR AC) HW-00002758 D1C1140 7128 1PCS 41 SCREW HW-00004198 Q1C 340 16128 1PCS 42

Miscellaneous:

REAR BRACKE

HW-00004381 15C5659503 1PCS 43 CARTON (E70f-5P) P-00004669 44C67A2709 4A 1PCS 44 CARTON (E70f-5M) P-00000867 44C67A2709 1A 1PCS 45 Carton (E70f-5EM) P-00004457 44C67B7709 1A 1PCS 46 P-00000865 44C67D3 1 1PCS 47 P-00000866 44C67D3 2 1PCS 48 Monitor PE BA

P-00004385 45C 88 7 RN 1PCS

Remark 1:

Above listed items are examples, supplier can expand the rows to add more necessary items.

Remark 2:

ViewSonic Model Number: VCDTS22355-5P

RECOMMENDED SPARE PARTS LIST (E70f-5P)

Description

All revised RSPLs with newly added items or any change made should be highlighted and correlated with the ECN/ECR approved by ViewSonic Corporation. This is to eliminate repeated cross checks of each item between this version and prior versions.

Cabinets:

Documentation:

Electronic Components:

EPS CUSHION (-5P/M)

Board Assembly:

Hardware:

Packing Material:

7. Recommended Spare Parts List

ViewSonic Corporation Confidential – Do Not Copy E70f-5_E70fB-5_E70fSB-5

Rev: 1c

Serial No. Prefix: P2D

Item ECR/ECN ViewSonic P/N Ref. P/N Location Universalnumber# Q'ty

Accessories:

POWER CORD (-5P/M)

A-00004583 89C420L18N IS 1PCS

CHASSIS FOR P773Z-1 VSC (-5P/M)

B-MB-0201-0707 CMP773Z1NVNL1 1PCS

3 CRT BOARD P773Z-1VSC B-VB-0202-030

CRP773Z1NVW 1PCS

4 FRONT PANE

C-00004586 34C 985BF0 A 1PCS

5 BACK COVE

C-00004587 34C 739 F0 1A 1PCS

6 BAS

C-00004588 34C 741 F0 L 1PCS

Cables:

SIGNAL CABL

CB-00004589 89C174L8ECBB

1PCS

8 CD MANUAL (E70f-5P/EM

)

DC-00004665 70C 747709 1F 1PCS

9 CD MANUAL (E70f-5M

)

DC-00004591 70C 747709 1E 1PCS

10 Capacitor 220UF +-20% 400V HEC E-C-0405-4331 67C 3022114D C907 1PCS 11 CPT 17" RF TCO BT CRT E-00004668 750A5C15EA

E750A 1PCS 12 CRT COCKET(QQ FOCUS) E-00002860 87C3504 ZW NA 1PCS 13 DEGAUSSING COI

E-00004666 750A1697504JAGNA 1PCS 14 Diode 1N5408 PEC E-00002714 93C 5255P52T D901,D902,D903,D904 4PCS 15 Diode RG-4S E-00004342 93C30408AT D919 1PCS 16 DRIVER TRANSFORME

E-T-0408-0526 79C 167125 LS T401 1PCS

17 FB

E-00002863 79A 763 BG 7 T402 1PCS 18 FOUCS E-00002862 79C 167126 HA T403 1PCS 19 FUSE 4A 250V LF-618 00

E-00002695 84A 7H400 SLF901 1PCS 20 IC 24LC08B/P

E-00002694 56C1133 13 IC102 1PCS 21 IC A 8PIN IC UC3842AM/LIN E-00004550 56C 379 12 IC901 1PCS 22 IC Amplier IC:LM2465TA E-00002697 56C 551 524 IC802 1PCS 23 IC LM1246DKA/NA/NOP

E-IC-0401-4019 56C 366509 IC801 1PCS 24 IC LM2480NA/NOPB E-IC-0401-2060 56C 539 6 IC803 1PCS 25 IC NT6863U-60026 E-00004339 56A1125566 IC101 1PCS 26 IC TDA4841PS/PHILIP

E-00002873 56C 552 2 IC401 1PCS

27 IC TDA4863A/PHILIP

E-00002874 56C 584 1A IC601 1PCS

28 Inductor 150UH +-10% FOR TD

E-00002875 73C 253 69 T L405 1PCS

29 Inductor CHOC

E-00002876 73C 253 88 HB L906 1PCS

30 LINEARITY COI

E-00004592 73C 147 538 H L401 1PCS

31 Main Transforme

E-00002864 80AS763 1NFHT901 1PCS 32 NTCR 15OHM+-15%2.5A THI E-00002858 61C 58 8T L NR901 1PCS 33 PTC

E-00002859 61C 52 27 4J PR901 1PCS 34 Transistor 2SC5929 E-00002865 57C 706505 Q403 1PCS 35 Transistor A TR.NPN TIP122/FAIRCHIL

E-00004340 57C 415 1 Q406 1PCS 36 Transistor CEPF630 BY CE

E-Q-0402-7029 57A 600 14 Q426,Q428,Q431 3PCS

37 Transistor IRF634

E-Q-0402-1508 57C 600 27 Q911 1PCS

38 Transistor STP9NK70ZF

E-00002867 57C 724501 Q901 1PCS 39 SCREW 3.5X10 HW-00004197 B1C1035 10128 1PCS 40 SCREW 4X7(FOR AC) HW-00002758 D1C1140 7128 1PCS 41 SCREW HW-00004198 Q1C 340 16128 1PCS 42

Miscellaneous:

REAR BRACKE

HW-00004381 15C5659503 1PCS

43 CARTON (E70f-5P

)

P-00004669 44C67A2709 4A 1PCS 44 CARTON (E70f-5M) P-00000867 44C67A2709 1A 1PCS 45 Carton (E70f-5EM

)

P-00004457 44C67B7709 1A 1PCS 46 P-00000865 44C67D3 1 1PCS 47 P-00000866 44C67D3 2 1PCS 48 Monitor PE BA

P-00004385 45C 88 7 RN 1PCS

Remark 1:

Above listed items are examples, supplier can expand the rows to add more necessary items.

Remark 2:

ViewSonic Model Number: VCDTS22355-5M

RECOMMENDED SPARE PARTS LIST (E70f-5M)

Description

Cabinets:

Documentation:

Electronic Components:

EPS CUSHION (-5P/M)

Board Assembly:

Hardware:

Packing Material:

ViewSonic Corporation Confidential – Do Not Copy E70f-5_E70fB-5_E70fSB-5

Rev: 1c

Serial No. Prefix: PUA

Item ECR/ECN ViewSonic P/N Ref. P/N Location Universalnumber# Q'ty

Accessories:

POWER CORD (-5EM)

A-0000458

89C404L18N IS 1PCS

CHASSIS FOR P773Z-1L VS (-5EM)

B-00004663 CMP773Z1NVW

1PCS 3 CRT BOARD P773Z-1VSC B-VB-0202-0304 CRP773Z1NVW 1PCS 4 FRONT PANEL C-00004586 34C 985BF0 A 1PCS 5 BACK COVER C-00004587 34C 739 F0 1A 1PCS 6 BASE C-00004588 34C 741 F0 L 1PCS

Cables:

SIGNAL CABL

CB-00004589 89C174L8ECBB

1PCS 8 CD MANUAL (E70f-5P/EM) DC-00004665 70C 747709 1F 1PCS 9 CD MANUAL (E70f-5M) DC-00004591 70C 747709 1E 1PCS

10 Capacitor 220UF +-20% 400V HEC E-C-0405-4331 67C 3022114D C907 1PCS 11 CPT 17" RF TCO BT CRT E-00004668 750A5C15EAV E750A 1PCS 12 CRT COCKET(QQ FOCUS) E-00002860 87C3504 ZW NA 1PCS 13 DEGAUSSING COIL E-00004666 750A1697504JAG NA 1PCS 14 Diode 1N5408 PEC E-00002714 93C 5255P52T D901,D902,D903,D904 4PCS 15 Diode RG-4S E-00004342 93C30408AT D919 1PCS 16 DRIVER TRANSFORMER E-T-0408-0526 79C 167125 LS T401 1PCS 17 FBT E-00002863 79A 763 BG 7 T402 1PCS 18 FOUCS E-00002862 79C 167126 HA T403 1PCS 19 FUSE 4A 250V LF-618 004 E-00002695 84A 7H400 SL F901 1PCS 20 IC 24LC08B/PG E-00002694 56C1133 13 IC102 1PCS 21 IC A 8PIN IC UC3842AM/LIN E-00004550 56C 379 12 IC901 1PCS 22 IC Amplier IC:LM2465TA E-00002697 56C 551 524 IC802 1PCS 23 IC LM1246DKA/NA/NOPB E-IC-0401-4019 56C 366509 IC801 1PCS 24 IC LM2480NA/NOPB E-IC-0401-2060 56C 539 6 IC803 1PCS 25 IC NT6863U-60026 E-00004339 56A1125566 IC101 1PCS 26 IC TDA4841PS/PHILIPS E-00002873 56C 552 2 IC401 1PCS 27 IC TDA4863A/PHILIPS E-00002874 56C 584 1A IC601 1PCS 28 Inductor 150UH +-10% FOR TDK E-00002875 73C 253 69 T L405 1PCS 29 Inductor CHOCK E-00002876 73C 253 88 HB L906 1PCS 30 LINEARITY COIL E-00004592 73C 147 538 H L401 1PCS 31 Main Transformer E-00002864 80AS763 1NFH T901 1PCS 32 NTCR 15OHM+-15%2.5A THI E-00002858 61C 58 8T L NR901 1PCS 33 PTCR E-00002859 61C 52 27 4J PR901 1PCS 34 Transistor 2SC5929 E-00002865 57C 706505 Q403 1PCS 35 Transistor A TR.NPN TIP122/FAIRCHILD E-00004340 57C 415 1 Q406 1PCS 36 Transistor CEPF630 BY CET E-Q-0402-7029 57A 600 14 Q426,Q428,Q431 3PCS 37 Transistor IRF634B E-Q-0402-1508 57C 600 27 Q911 1PCS 38 Transistor STP9NK70ZFP E-00002867 57C 724501 Q901 1PCS 39 SCREW 3.5X10 HW-00004197 B1C1035 10128 1PCS 40 SCREW 4X7(FOR AC) HW-00002758 D1C1140 7128 1PCS 41 SCREW HW-00004198 Q1C 340 16128 1PCS 42

Miscellaneous:

REAR BRACKE

HW-00004381 15C5659503 1PCS 43 CARTON (E70f-5P) P-00004669 44C67A2709 4A 1PCS 44 CARTON (E70f-5M) P-00000867 44C67A2709 1A 1PCS 45 Carton (E70f-5EM) P-00004457 44C67B7709 1A 1PCS 46 P-00004660 44C67E7 1 1PCS 47 P-00004661 44C67E7 2 1PCS 48 Monitor PE BA

P-00004385 45C 88 7 R

1PCS

Remark 1:

Above listed items are examples, supplier can expand the rows to add more necessary items.

Remark 2:

RECOMMENDED SPARE PARTS LIST (E70f-5EM)

Description

Cabinets:

Documentation:

Electronic Components:

EPS CUSHION (-5EM)

Board Assembly:

Hardware:

Packing Material:

ViewSonic Model Number: VCDTS22355-5E

ViewSonic Corporation Confidential – Do Not Copy E70f-5_E70fB-5_E70fSB-5

Rev: 1a

Serial No. Prefix: 26F

Item ECR/ECN ViewSonic P/N Ref. P/N Location Universal number# Q'ty

Accessories:

Power Cord A-PC-0106-0209 89C402A18N YH 89C402A18NYH 1PCS

CRT Board P773Z-1VSC

B-VB-0202-030

CRP773Z1NVW

CRP773Z1NVW 1PCS

3 Main Board (Chassis for P773Z-1 VSC) B-00004654

CMP773Z1NVOL1

CMP773Z1NVOL1 1PCS 4 Back Cover C-00004670 34C 739 E7 1A 34C739E71A 1PCS 5 Base Assembly C-00002683 34C 741 QE L 34C741QEL 1PCS 6 Front Panel C-00004671 34C 985EE7 A 34C985EE7A 1PCS 7

Cables:

Signal Cable

CB-00004337 89C174B8ECLB

89C174B8ECLB21PCS

Documentation:

Quick Start Guide

DC-00004672 41C 6870913A 41C6870913A 1PCS

Capacitor 220UF +-20% 400V HEC

E-C-0405-4331 67C 3022114D

C907

67C3022114D 1PCS

10 Diode 1N5408 PEC E-00002714 93C 5255P52T

D902

93C5255P52T 1PCS

11 Diode ER202 E-D-0403-2093 93C2020 552T

D923

93C2020552T 1PCS

12 Diode FMP-2FUR 1500/600V 5A S E-00002715 93C 220 12

D408

93C22012 1PCS

13 Diode RG-4S E-00004342 93C30408AT

D919

93C30408AT 1PCS

14 Diode RG-4S E-00004342 93C30408AT

D925

93C30408AT 1PCS

15 Flyback Transformer E-00002863 79A 763 BG 7

T402

79A763BG7 1PCS

16 Fuse Clip E-00004658 84C 33 10

F901

84C3310 1PCS

17 IC 24LC08B/PG E-00002694 56C1133 13

IC102

56C113313 3PCS

18 IC A 8PIN IC UC3842AM/LIN E-00004550 56C 379 12

IC901

56C37912 1PCS

19 IC LM1246DKA/NA/NOPB E-IC-0401-4019 56C 366509

IC801

56C366509 1PCS

20 IC LM2470TA/NOPB E-00002697 56C 551524

IC802

56C551524 1PCS

21 IC NT68F63U E-IC-0401-4017 56A1125552 X

IC101

56A1125552

1PCS

22 IC TDA4841PS/PHILIPS E-00002873 56C 552 2

IC401

56C5522 1PCS

23 IC TDA4863A/PHILIPS E-00002874 56C 584 1A

IC601

56C5841A 1PCS

24 NTCR 15OHM+-15%2.5A THI E-00002858 61C 58 8T L

NR901

61C588T

1PCS

25 PTCR E-00002859 61C 52 27 4J

PR901

61C52274J 1PCS

26 Transistor 2SC5929 E-00002865 57C 706505

Q403

57C706505 1PCS

27 Transistor A TR.NPN TIP122/FAIRCHILD E-00004340 57C 415 1

Q406

57C4151 1PCS

28 Transistor HSB772P/E E-00002866 57C 728 3

Q909

57C7283 4PCS

29 Transistor IRF634B E-Q-0402-1508 57C 600 27

Q911

57C60027 1PCS

30 Transistor MOSFET E-00004066 57C 600 14

Q428

57C60014 1PCS

31 Transistor STP9NK70ZFP E-00002867 57C 724501

Q901

57C724501 1PCS 32 Carton P-00004673 44C67B7709 1B 44C67B77091B 1PCS 33 EPS Cushion P-00004660 44C67E7 1 44C67E71 1PCS 34 EPS Cushion P-00004661 44C67E7 2 44C67E72 1PCS

Remark 1:

Above listed items are examples, supplier can expand the rows to add more necessary items.

Remark 2: All revised RSPLs with newly added items or any change made should be highlighted and correlated with the ECN/ECR approved

by ViewSonic Corporation. This is to eliminate repeated cross checks of each item between this version and prior versions.

ViewSonic Model Number: VCDTS22355-5M

RECOMMENDED SPARE PARTS LIST (E70fSB-5M)

Description

Board Assembly:

Cabinets:

Electronic Components:

Packing Material:

ViewSonic Corporation Confidential – Do Not Copy E70f-5_E70fB-5_E70fSB-5

Rev: 1a

Serial No. Prefix: PJ8

Item ECR/ECN ViewSonic P/N Ref. P/N Location Universal number# Q'ty

Accessories:

POWER CORD A-00004653

89C404A18N YH

1PCS

2 CRT BOARD P773Z-1VSC B-VB-0202-0304

CRP773Z1NVW

1PCS

3 CHASSIS FOR P773Z-1 VSC B-00004654

CMP773Z1NVOL1

1PCS 4 FRONT PANEL C-00004553 34C 985BFJ T 1PCS 5 BACK COVER C-00004655 34C 739 FK 1T 1PCS 6 BASE ASSEMBLY C-00004656 34C 741 QD B 1PCS 7

Cables:

SIGNAL CABL

CB-00004337 89C174B8ECLB

1PCS 8

Documentation:

CD MANUAL DC-00004657 70C 747709 1G 1PCS

9 1N5408 PEC E-00002714 93C 5255P52T

D902

1PCS

10 220UF +-20% 400V HEC E-C-0405-4331 67C 3022114D

C907

1PCS

11 2SC5929 E-00002865 57C 706505

Q403

1PCS

12 A 8PIN IC UC3842AM/LIN E-00004550 56C 379 12

IC901

1PCS

13 A TR.NPN TIP122/FAIRCHILD E-00004340 57C 415 1

Q406

1PCS

14 ER202 E-D-0403-2093 93C2020 552T

D923

1PCS

15 FMP-2FUR 1500/600V 5A S E-00002715 93C 220 12

D408

1PCS

16 FUSE 4A 250V LF-618 004 E-00002695 84A 7H400 SL

F901

1PCS

18 FUSE CLIP E-00004658 84C 33 10

F901

1PCS

19 HSB772P/E E-00002866 57C 728 3

Q909

1PCS

20 IC 24LC08B/PG E-00002694 56C1133 13

IC102

1PCS

21 IC IRF634B E-Q-0402-1508 57C 600 27

Q911

1PCS

22 IC LM1246DKA/NA/NOPB E-IC-0401-4019 56C 366509

IC801

1PCS

23 IC LM2470TA/NOPB E-00002697 56C 551524

IC802

1PCS

24 IC NT6865UG-30135 E-00004659 56C1125566 A

IC101

3PCS

25 IC TDA4841PS/PHILIPS E-00002873 56C 552 2

IC401

1PCS

26 IC TDA4863A/PHILIPS E-00002874 56C 584 1A

IC601

1PCS

27 MOSFET E-00004066 57C 600 14

Q428

4PCS

28 NT68F63U E-IC-0401-4017 56A1125552 X

IC101

1PCS

29 NTCR 15OHM+-15%2.5A THI E-00002858 61C 58 8T L

NR901

1PCS

30 PTCR E-00002859 61C 52 27 4J

PR901

1PCS

31 RG-4S E-00004342 93C30408AT

D919

1PCS

32 RG-4S E-00004342 93C30408AT

D925

1PCS

33 STP9NK70ZFP E-00002867 57C 724501

Q901

1PCS

CARTON

P-00004458

44C67B7709 4A

1PCS

35 P-00004660 44C67E7 1 1PCS 36 P-00004661 44C67E7 2 1PCS

Remark 1:

Above listed items are examples, supplier can expand the rows to add more necessary items.

Remark 2:

ViewSonic Model Number: VCDTS22355-5E

RECOMMENDED SPARE PARTS LIST (E70fSB-5E)

Description

Board Assembly:

Cabinets:

Electronic Components:

Packing Material:

EPS CUSHION

ViewSonic Corporation Confidential – Do Not Copy E70f-5_E70fB-5_E70fSB-5

+ 73 hidden pages

ViewSonic E70FSB-2 - E 70F+SB - 17"" CRT Display, E70f-5, E70fB-5, E70fSB-5, VCDTS22355-5 Service Manual

Specifications and Main Features

Frequently Asked Questions

User Manual