ViewSonic makes no representations or warranties, either expressed or implied, with respect to
the contents hereof and specifically disclaims any warranty of merchantability or fitness for any
particular purpose. Further, ViewSonic reserves the right to revise this publication and to make
changes from time to time in the contents hereof without obligation of ViewSonic to notify any
person of such revision or changes.
Trademarks
Opt quest is a registered trademark of ViewSonic Corporation.
ViewSonic is a registered trademark of ViewSonic Corporation.
All other trademarks used within this document are the property of their respective owners.
Revision History
Revision SM Editing Date ECR Number Description of Changes Editor
ViewSonic Corporation Confidential - Do Not CopyQ7b-3
i
TABLE OF CONTENTS
1. Precautions and Safety Notices 1
2. Specification 5
3. Front Panel Function Control Description 13
4. Circuit Description 19
5. Adjustment Procedure 24
6. Troubleshooting Flow Chart 45
7. Recommended Spare Parts List 53
8. Exploded Diagram and Exploded Parts List 60
9. Block Diagram 62
10. Schematic Diagrams 63
11. PCB Layout Diagrams 70
ViewSonic Corporation Confidential - Do Not CopyQ7b-3
ii
1. Precautions and Safety Notices
1. Appropriate Operation
(1) Turn off the product before cleaning.
(2) Use only a dry soft cloth when cleaning the LCD panel surface.
(3) Use a soft cloth soaked with mild detergent to clean the display housing.
(4) Use only a high quality, safety approved AC/DC power cord.
(5) Disconnect the power plug from the AC outlet if the product will not be used for a long period of time.
(6) If smoke, abnormal noise, or strange odor is present, immediately switch the LCD display off.
(7) Do not touch the LCD panel surface with sharp or hard objects.
(8) Do not place heavy objects on the LCD display, video cable, or power cord.
(9) Do not use abrasive cleaners, waxes or solvents for your cleaning.
(10) Do not operate the product under the following conditions:
- Extremely hot, cold or humid environment.
- Areas containing excessive dust and dirt.
- Near any appliance generating a strong magnetic field.
- In direct sunlight.
2. Caution
No modification of any circuit should be attempted. Service work should only be performed after you are thoroughly familiar
with all of the following safety checks and servicing guidelines.
3. Safety Check
Care should be taken while servicing this LCD display. Because of the high voltage used in the inverter circuit, the voltage is
exposed in such areas as the associated transformer circuits.
4. LCD Module Handling Precautions
4.1 Handling Precautions
(1) Since front polarizer is easily damaged, pay attention not to scratch it.
(2) Be sure to turn off power supply when connecting or disconnecting input connector.
(3) Wipe off water drops immediately. Long contact with water may cause discoloration or spots.
(4) When the panel surface is soiled, wipe it with absorbent cotton or other soft cloth.
(5) Since the panel is made of glass, it may break or crack if dropped or bumped on hard surface.
(6) Since CMOS LSI is used in this module, take care of static electricity and ensure human earth when handling.
(7) Do not open or modify the Module Assembly.
(8) Do not press the reflector sheet at the back of the module in any direction.
(9) In the event that a Module must be put back into the packing container slot after it was taken out of the
container, do not press the center of the CCFL Reflector edge. Instead, press at the far ends of the
CFL Reflector edge softly. Otherwise the TFT Module may be damaged.
(10) At the insertion or removal of the Signal Interface Connector, be sure not to rotate or tilt the Interface
Connector of the TFT Module.
ViewSonic Corporation Confidential - Do Not CopyQ7b-3
1
(11)After installation of the TFT Module into an enclosure (LCD monitor housing, for example), do not twist or
bend the TFT Module even momentarily. When designing the enclosure, it should be taken into consideration
that no bending/twisting forces may be applied to the TFT Module from outside. Otherwise the TFT Module
may be damaged.
(12) The cold cathode fluorescent lamp in the LCD contains a small amount of mercury. Please follow local
ordinances or regulations for disposal.
(13) The LCD module contains a small amount of materials having no flammability grade. The LCD module
should be supplied with power that complies with the requirements of Limited Power Source
(IEC60950 or UL1950), or an exemption should be applied for.
(14)The LCD module is designed so that the CCFL in it is supplied by a Limited Current Circuit (IEC60950
or UL1950). Do not connect the CCFL to a Hazardous Voltage Circuit.
ViewSonic Corporation Confidential - Do Not CopyQ7b-3
2
Handing and Placing methods
Correct methods Incorrect methods
Only touch the metal frame of the LCD panel or the
front cover of the monitor, DO not touch the surfaceof
the POL
Surface of the LCD panel is pressed by fingers and that
may cause”mura”
Take out the monitor with cushions Taking out the monitor by grasping the LCD panel, that
May cause”mura”
ViewSonic Corporation Confidential - Do Not CopyQ7b-3
3
Place the monitor on a clean and soft foam pad Placing the monitor on a foreign objects, that could
scratch The surface of the "Panel" or cause "mura"
The panel is placed facedown the lap,that may cause
"mura"
ViewSonic Corporation Confidential - Do Not CopyQ7b-3
4
2. Specification
Equal to twice the weight of the monitor for five
Shall be compatible with all PC type computers,
Macintosh computers, and after market video
2-1 GENERAL specification
Test Resolution & Frequency 1280x1024 @ 75Hz
Test Image Size Full Size
Contrast and Brightness Controls
2-2 VIDEO INTERFACE
Input Connector (refer the appendix A) DB-15 (Analog)
Default Input Connector Defaults to the first detected input
ViewSonic Corporation Confidential - Do Not CopyQ7b-3
5
2-4 POWER SUPPLY
Shall be able to withstand 1.5 times nominal line
Shall be able to function properly, without reset or
visible screen artifacts, when ½ cycle of AC power
The power supply shall not produce audible noise
that would be detectable by the user. Audible
shall defined to be in compliance with ISO 7779
(DIN EN27779:1991) Noise measurements of
r Switch noise shall not
Internal Power Supply
FSP FSP035-1PI01ZT
Input Voltage Range 90 to 264 VAC
Input Frequency Range 47.5 to 63 Hertz
Short Circuit Protection
Output can be shorted without damage
Over Current Protection 5.0 A typical at 12.0 VDC
Leakage Current 3.5mA (Max) at 254VAC / 60Hz
Efficiency 80 % typical at 115VAC Full Load
Fuse
Power Dissipation
Max Input AC Current
Internal and not user replaceable
36W(typ) 40W(max)
1.5 Arms @ 90VAC, 0.75 Arms @180VAC
50 A (max) @ 115VAC
Inrush Current (Cold Start)
90 A (max) @ 230VAC
Shall start and function properly when under full
load, with all combinations of input voltage, input
Power Supply Cold Start
frequency, and operating temperature.
Shall be able to withstand an ANSI/IEEE
Power Supply Transient Immunity
C62.41-1980 6000V 200 ampere ring wave
transient test with no damage.
Power Supply Line Surge Immunity
Power Supply Missing Cycle Immunity
voltage for one cycle with no damage.
is randomly missing at nominal input.
Power Supply Acoustics
machines acoustics. Powe
be considered.
Power Saving Operation(Method)
Power Consumption
VESA DPMS Signaling
On Mode < 36W(Typ) / 40W (max)
Active Off < 1 W @ 120 Vac /
< 1.5W @ 220Vac
Recovery Time On Mode = N/A, Active Off < 3 sec
ViewSonic Corporation Confidential - Do Not CopyQ7b-3
6
2-5 ELECTRICAL REQUIREMENT
Horizontal / Vertical Frequency
Horizontal Frequency 30 – 80 kHz
Vertical Refresh Rate 55 – 75 Hz.
Maximum Pixel Clock 135 MHz
Sync Polarity Independent of sync polarity.
Timing Table
Timing
Analog Item
Composite
Separated
Digital - TMDS
SOG
Remark
640 x 350 @ 70 Hz, 31.5 KHz
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
640 x 480 @ 60 Hz, 31.5 KHz
640 x 480 @ 67 Hz, 35 KHz
640 x 480 @ 72 Hz, 37.9 KHz
640 x 480 @ 75 Hz, 37.5 KHz
720 x 400 @ 70 Hz, 31.5 KHz
800 x 600 @ 56 Hz, 35.1 KHz
800 x 600 @ 60 Hz, 37.9 KHz
800 x 600 @ 72 Hz, 48.1 KHz
800 x 600 @ 75 Hz, 46.9 KHz
832 x 624 @ 75 Hz, 49.7 KHz
1024 x 768 @ 60 Hz, 48.4 KHz
1024 x 768 @ 70 Hz, 56.5 KHz
1024 x 768 @ 75 Hz, 60.2 KHz
1152 x 864 @ 75 Hz, 67.5 KHz
1152 x 870 @ 75 Hz, 68.7 KHz
1280 x 960 @ 60 Hz, 59.7 KHz
1280 x 1024 @ 60 Hz, 64 KHz
1280 x 1024 @ 75 Hz, 80 KHz
The vertical image size might not full
screen
(vertical position = center).
Primary Presets
1280x1024 @ 75Hz
User Presets
Number of User Presets (recognized timings) Available: 10 presets total in FIFO configuration
Changing Modes
● Maximum Mode Change Blank Time for image stability : 3 seconds (Max), excluding “Auto
Adjust” time
● The monitor needs to do “Auto Adjust” the first time a new mode is detected
(see section “0-Touch™ Function Actions”)
● While running Change Mode, Auto Adjust or Memory Recall, the image shall blank
ViewSonic Corporation Confidential - Do Not CopyQ7b-3
7
2-6 FRONT PANEL CONTROLS AND INDICATORS
The OSD shall save new settings when it is turned off by the user or when it times out.
Front Panel Hardware Controls
Power Switch (Front Head) Power Control, soft Power Switch.
Power LED (Front Head) Green – ON
Orange – Active Off
Dark = Soft Power Switch OFF
Front Panel Controls
(Head; From left to right)
BUTTON ICON FUNCTION
BUTTON1
BUTTON2
BUTTON3
BUTTON4
BUTTON5
SELECT(BACKWARD)
SELECT(FORWARD)
POWER
-
ADJUST DOWN
+
ADJUST UP
Reaction Time OSD must fully appear within 0.5s after pushing
Button 1
Short Cuts Function from the button(s)
Button 1 Auto Image Adjust.
Button 2 Main Menu
Button 4 Mute on/off
Button 5 Volume OSD
Button 4 + Button 5
+ Button 3
Factory Mode
(The Burning mode is build in Factory mode)
Remark : All the short cuts function are only available while OSD off
Function descriptions
Main Menu Controls
The Main Menu OSD include most of control functions.
Please refer to APPENDIX B (Main Menu OSD Table) for the detail.
Factory Default OSD Actions
Memory Recall action on the analog and digital mode as below
1. Set the factory defaults as shown in Section 2-8
2. Clean all the mode setting buffer
3. Execute Auto Image Adjust
0-Touch™ Function Actions
1. Execute Auto Image Adjust when new mode detected, and save the settings to buffer for
further use
2. It should be reset by Memory Recall function
(Should not reset by power off, power unplug and others)
OSD Auto Save
There shall not be a separate save
Factory Defaults
Item Defaults
Contrast 90
Brightness 100
Color Setting NATIVE
ViewSonic Corporation Confidential - Do Not CopyQ7b-3
8
2-7 AUDIO INTERFACE (SPEAKER SPECIFICATION)
SPEAKER SPECIFICATION
LINE INPUT CONNECTION 3.5 MM STEREO JACK
LINE INPUT SIGNAL 0.7 VRMS
LINE INPUT IMPEDANCE 18 KOHM
MAXIMUM POWER OUTPUT
(ELECTRIC)
1 W@ < 15 % DISTORTION
SIGNAL TO NOISE RATIO 50 DB
FREQUENCY RESPONSE 200 HZ – 10 KHZ
DISTORTION < 5 % THD (@1KHZ)
THERE SHOULD BE NO AUDIBLE
VIBRATION
VIBRATION WITH VOLUME AT 100% AND
TREBLE / BASS AT DEFAULT.
THERE SHOULD BE NO AFFECT ON THE
SCREEN IMAGE
SCREEN IMAGE STABILITY UNDER ANY
CONDITIONS.
CONNECTOR PC99 REQUIREMENT
AUDIO IN
LIME GREEN PANTONE # 577C
CABLE TYPE / LENGTH 3.5MM STEREO CABLE / 1.8M LENGTH
SPEAKERS SHOULD BE OFF WHEN THE
AUDIO DPMS
REST OF THE MONITOR IS IN POWER
SAVING.
UNDER FOLLOWING CONDITIONS, THERE
SHOULD BE NO SYMPATHETIC HEARD
SYMPATHETIC
1. INPUT <=0.7VRMS
2. VOLUME OSD <=80
3. DISTANCE =30CM ±5CM
ViewSonic Corporation Confidential - Do Not CopyQ7b-3
9
2-8 TFT LCD PANEL
Panel Characteristics:
1st Source Panel
Model number CMO M170E5-L09 (17”)
Type Active Matrix TFT, TN technology
Pixel Arrangement RGB Vertical Stripe (0.264 mm Pixel Pitch)
Glass Treatment Anti-Glare, Hard Coating (3H)
# of Backlights 4 CCFL
Backlight Life 50,000 Hrs (Typical)/40,000 Hrs (Min)
Luminance (Center) 300 cd/m2 (Typical) /230 cd/m2 (Min)
Brightness Uniformity 80% (Typical) / 75% (Min)
Contrast Ratio 500 :1 (Typical) / 400 : 1 (Min)
Color Depth 16.2 million colors (6+2 bit panel)
Viewing Angle (CR>10) (H) 150°/ (V)130°
Response Time 10%-90% @ Ta=25°C On/Off : 8 ms
Mercury 3.0 mg per lamp
* P50% units of monthly shipment shall be equal or better than the Typical value above.
2nd Source Panel
Model number Innolux MT170EN01 (17”)
Type Active Matrix TFT, TN technology
Pixel Arrangement RGB Vertical Stripe (0.264 mm Pixel Pitch)
Glass Treatment Anti-Glare, Hard Coating (3H)
# of Backlights 4 CCFL
Backlight Life 50,000 Hrs (Min)
Luminance (Center) 280 cd/m2 (Typical) / 250 cd/m2 (Min)
Brightness Uniformity 80% (Typical) / 75% (Min)
Contrast Ratio 600 :1 (Typical) / 500 : 1 (Min)
Color Depth 16.2 million colors (6+2 bit panel)
Viewing Angle (CR>10) (H)150° degrees (V) 135°
Viewing Angle (CR>5) (H)170°(Typical) / (V)155°(Typical)
Response Time 10%-90% @ Ta=25°C On/Off : 8 ms
Mercury 3.0 mg per lamp
* P50% units of monthly shipment shall be equal or better than the Typical value above.
rd
Source Panel
3
Model number SVA SVA170SX01TB
Type Active Matrix TFT, TN technology
Pixel Arrangement RGB Vertical Stripe (0.264 mm Pixel Pitch)
Glass Treatment Anti-Glare
# of Backlights 4 CCFL
Backlight Life 50,000 Hrs (Typical) / 42,000 Hrs (Min)
Luminance (Center) 300 cd/m2 (Typical) / 240 cd/m2 (Minimum)
Brightness Uniformity 83% (Typical) / 77% (Minimum)
Contrast Ratio 600 :1 (Typical) / 400 : 1 (Minimum)
Color Depth 16.77million colors (6bit panel)
Viewing Angle (CR>10) (H)130° / (V) 110°
Response Time 10%-90% @ Ta=25°C On/Off : 8 ms
Mercury <3.0 mg per lamp
* P50% units of monthly shipment shall be equal or better than the Typical value above.
ViewSonic Corporation Confidential - Do Not CopyQ7b-3
10
2-9 IMAGE PERFORMANCE
Lv (Max) = The Luminance requirement of
6
Display Size
Horizontal Display Size, Primary Preset Full Screen
Vertical Display Size, Primary Preset Full Screen
Luminance
Lv (Max) –Condition:
Brightness / Contrast = 100%
Color Temperature = User (R/G/B=100)
section 2-6 “TFT LCD PANEL”
Lv (NATIVE) –Condition:
Brightness = Default / Contrast = Default
Color Temperature = NATIVE
Lv (NATIVE) / Lv (Max) x 100% > 85%
Lv (COOL) –Condition:
Brightness = Default / Contrast = Default
Color Temperature = COOL
Lv (COOL) / Lv (Max) x 100% > 70%
Lv (WARM) –Condition:
Brightness = Default / Contrast = Default
Color Temperature = WARM
Lv (WARM) / Lv (Max) x 100% > 70%
Contrast Ratio
CR(Max) –Condition:
Contrast / Brightness = 100%
Color Temperature = User (R/G/B=100)
Same as the Contrast Ratio in section 2“TFT LCD PANEL”
Saturation
Contrast = Default
Brightness = Default
NO VISIBLE SATURATION
Test pattern = 128-gray
Preset Color Temperatures
Color Temperature = WARM
(CCT around 5500K)
x = 0.332 ± 0.03
y = 0.348 ± 0.03
Color Temperature = NATIVE
(CCT around 6500K)
x = 0.313 ± 0.03
y = 0.329 ± 0.03
Color Temperature = COOL
(CCT around 9300K)
x = 0.283 ± 0.03
y = 0.298 ± 0.03
*No redish, greenish or bluish tint under any color setting (base on PVT sample)
Video Cards Compatibility
Peaking Performance : Peaking is not adjustable
Raster Artifacts
● Video Artifacts : No visible streaking, sag, or smearing artifacts when driven by the
specified video cards in the primary mode and after user adjustment to best condition
● Power Supply, and Grounding Artifacts : No visible artifacts in any specified video mode
within the horizontal or vertical frequency range of the monitor
● Temperature Drift : Image shall not drift or lose fine-tune adjustment
ViewSonic Corporation Confidential - Do Not CopyQ7b-3
11
2-10 MECHANICAL
tic cabinet components shall
be in compliance with the requirements of
Neck, Base, Speaker Cover, Rear Cover
Cover, Rear Cover and Rear Logo is the Black
Light shall be less
“Delta E” in the 1976 CIE L*a*b
ormed
according to the requirements of ASTM Test
Tech # 11010 used on all external
The supplier shall submit textured color chips,
plastic material specifications, and Material
Desktop
Dimension 375 mm (W) x 372 mm (H) x 160 mm (D)
14.8" (W) x 14.6" (H) x 6.3" (D)
Monitor Weight 4.2 Kg (9.3 lbs)
Head Only / Wall Mount
Dimension 375 mm (W) x 323 mm (H) x 56 mm (D)
14.8" (W) x 12.7" (H) x 2.2" (D)
Monitor Weight 3.9 Kg (8.6 lbs)
Ergonomics
Tilt Up +15º ±2 º
Tilt Down -5 º ±2 º
Cabinet Material
Display Head Plastic Material ABS-94HB
Neck/Base Plastic Material ABS-94HB
All internal plas
Internal Plastic Cabinet Components
MPR II
Front Bezel Color
and Rear Logo Color
Cabinet Color Drift Due To UV-Light
Cabinet Texture
The reference for the Front Bezel is the Black
color chip provided by ViewSonic
The color difference between any two cabinet
components shall be less than 0.80 “Delta E”, in the
1976 CIE L*a*b Colorspace.
The reference for the Neck, Base, Speaker
color chip provided by ViewSonic
The color difference between any two cabinet
components shall be less than 0.80 “Delta E”,
in the 1976 CIE L*a*b Colorspace.
The color drift due to UVthan 3.0
colorspace. Testing shall be perf
Method D4459-93.
Mold-
textured surfaces.
Samples
ViewSonic CorporationConfidential - Do Not CopyQ7b-3
Safety Data Sheets for approval.
12
3. Front Panel Function Control Description
3.1 Functional Description of Controls
a. User Control Panel
b. Description of Key Functions
No. Symbol
•
‚
ƒ
„
…
†
3.2 LED Indicator
The Model has one power LED which has two colors,Green and Amber.
LED should have enough luminance for clear viewable.
Function
1. Show the mute OSD.
2. Decrease a function’s (
3. Move to the next function (
1. Show the volume OSD menu
2. Increase a function’s (
3. Move to the next function (
Power indicator
Turn the power on or off
1. Show the main OSD menu
2. Select the next OSD icon down
1. Auto-adjust
2. Select the next OSD icon up
)
value.
)
value.
) left
) right
Some monitor status area indicated by using this LED, as follows:
Power LED
Normal On Green
Suspend Amber
Active Off Off
Out of Range Amber
No Input Signal Amber (OSD ON)
ViewSonic Corporation Confidential - Do Not CopyQ7b-3
13
3.3 User Adjustment (At Analog Signal input)
Hot Key
OSD
RGB Mode
Auto Adjuster
Brightness
Contrast
H position
V position
Phase
Clock
Color
Slider Bar
Brightness
Up
User
Native
Cool
Color Red
Color Green
Color Blue
Language
Reset
Exit
Brightness
Down
3.4 Specification (at all Present Timing)
a. BRT / CONT:
Picture background shall become brighter with BRIGHTNESS at its MAX position, and shall
become darker at its MIN position.
Contrast of picture shall be changed by adjusting contrast value.
b. Adjusted Range for H/V Center : ±10mm or more / ±5mm or more
c. Adjusted Range for H Phase / Pitch : >60 steps / ±50 dots
d. Color : Standard Shipping Condition- Native
Preset Color Mode - Cool, Native, Warm. User Adjustment Mode- Users can adjust each R or G or B color individually.
ViewSonic Corporation Confidential - Do Not CopyQ7b-3
14
D G
A C
e. Recall : Recall include Brightness, Contrast, Volume, OSD Position, OSD Time, and execute
Auto Adjust.
f. Language: Users can choose one of the eight languages:English, French, German, Spanish and
g. Power: Pushing Power button shall cause the monitor to be turned ON and LED to be
illuminated.
Pushing Power button again shall cause the monitor to be turned OFF and LED to be OFF.
3.5 Other User/Service Information
a. SIGNAL OVER RANGE:
If the horizontal or vertical or both input signal frequency exceed the acceptable input frequency
range, the monitor keeps indicating the “SIGNAL OVER RANGE” as the OSD information after
2 seconds. If both input signal frequencies are in the acceptable frequency range, the monitor
puts out the OSD indication and goes back to normal state.
b. RGB NO INPUTSIGNAL:
In case of the pin 14 is +5V, the monitor recognizes PC is connected. Otherwise, the pin 14 is
low (approx. 0V), horizontal or vertical input signals are not exist, the monitor displays OSD
information〝RGB NO INPUTSIGNAL〞5 seconds, then goes to power save.
3.6 Picture Size & Tilt (Primary mode only; to be checked in shipping condition.)
a. Picture Size: <All Models> Follow Panel Spec.
b. Tilt:
B’
D’
bezel
B
| AB- CD| = Tilt on top≦ 1mm
| EF - GH| = Tilt on bottom ≦ 1mm
video
| BB’-EE’| ≦ 1mm (at left side)
E’
E
G’
| DD’-GG’| ≦ 1mm (at right side)
F H
ViewSonic Corporation Confidential - Do Not CopyQ7b-3
15
3.7 Brightness Uniformity and Contrast Ratio
C D
a. Brightness Uniformity:
128 640 1152
B
E
A
102
512
922
Bmax = MAX (BA, BB, BC, BD, BE)
Bmax - Bmin Bmin = MIN (BA, BB, BC, BD, BE)
≦ 20%
Bmax Bave = AVE (BA, BB, BC, BD, BE)
b. Contrast Ratio:
The contrast ratio is measured at point A and calculated by using the following formula
Luminance with all pixels in white
Contrast ratio (CR) = ≧ 400(According to CMO
Luminance with all pixels in black M170E5-L09)
3.8 Shipping Luminance
a. Condition Input signal : Full white pattern
Controls : Color temperature of Office
Cont./Brt. : Default value
Measurement point: One point at the center of the picture.
Warm-up time : 30 minutes.
Color analyzer : CA-210
c. Shipping luminance (center)
Shipping Luminance
Color Temperature
17”
Native
≧ 230 cd / ㎡
3.9 Maximum / Minimum Luminance
a. Condition Input signal : Full white pattern (Primary mode)
Measurement point : Center of LCD screen
Color Analyzer : CA-210
Maximum : BRT→Max.
CONT→Max.
b. Specification: Native only
(1) ≧230 cd/㎡
ViewSonic Corporation Confidential - Do Not CopyQ7b-3
16
3.10 Black Level
a. Gray Scale Condition Input signal: 32 Gray scale (Primary mode)
Controls : CONT./BRT. primary setting, other shipping setting
condition.
b. Specification:Native (1) The first bar from black of gray scale pattern shall be cut off.
(2) The last bar from the bright of gray scale pattern shall be
discrimination.
3.11 Picture Quality
a. Condition BRT : MIN. ~ MAX.
CONT: MIN. ~ MAX.
*Inspection of picture quality shall be made at the distance of 50 cm in front of LCD surface.
b. Full White Signal
Condition: Input signal – Full white signal
Specification: The following electrical defects shall not be so conspicuous.
(ITU-R 4.5 or better in primary mode, and ITU-R 4.0 or better in other modes)
(2) ringing, seam, etc.
(3) flicker, noise, beat, etc.
(4) shading, etc.
(5) saturation of video power supply, etc.
c. Inverted Crosshatch Signal
Condition: Input signal – Inverted crosshatch signal
Specification: Following electrical defects shall not be so conspicuous.
(ITU-R 4.5 or better in primary mode, and ITU-R 4.0 or better in other modes)
(1) video ringing, over shoot, smear, etc.
(2) vertical jitter, horizontal jitter, picture vibration, etc.
d. Gray Scale Signal
Condition: Input signal – Gray scale signal
Specification: Following electrical defects shall not be so conspicuous.
(ITU-R 4.5 or better in primary mode, and ITU-R 4.0 or better in other modes)
(1) Oscillation, noise, beat, shading, etc.
ViewSonic Corporation Confidential - Do Not CopyQ7b-3
17
3.12 EDID DATA
a. Condition : Maintain Mode
b. Specification : FOR RGB
DDC EDID 128 BYTES DATA STRUCTURE
No. Item EDID Data or Definition
00 Header 00 FF FF FF FF FF FF 00
08 ID Manufacturer Name 10 8C (DDL)
0A ID Product Code 00 00 (0)
0C ID Serial Number 00 00 00 00 (0)
10 Week Of Manufacture Week of manufacture
11 Year Of Manufacture Year of manufacture
12 EDID Version,Revision 01 03
14 Video Input Definition 7E(Analog signal,0.700,0.000(0.7
on Screen )
15 Max. H. Image Size 22 (34cm)
16 Max. V. Image Size 1B(27cm)
17 Display Transfe
Charac.(gamma)
18 Feature Support(DPMS) EB(Stand-by,Suspend,Active Off supported,R/G/B color display)
19 Color Characteristics Per TFT measurement(See NOTE1)
ViewSonic Corporation Confidential - Do Not CopyQ7b-3
18
4. Circuit Description
A. A/D converters
The ADC is a 7-bit 4-channel analog-to digital converter ,the structure of these ADCS is 7-bit
successive approximation ,analog voltage is supplied from external sources to the A/D input pins and
the result of the conversion is stored In the 7-bit data latch registers(ADC0_REG~ADC3_REG).The
A/D cannels are activated by cleaning the correspondent control bits in the ADC_CON control register,
when users write”1” into one of the enable control bits(EN_ADC0~EN-ADC3),its correspondent I/O pin
will be switched to the A/D Converter input pin
The conversion will be started by setting STRT_ADC Bit, user can monitor this bit to get the valid A/D
channel, its latched data is meaningful, the analog voltage to be measured should be stable during the
conversion operation and the variation will not exceed 1 LSB for the best accuracy in measurement
B.Scalling controller
1. VGA front end
l Built-in triple high speed ADC,PLL for analog RGB input
l Supports both non-interlaced and interlaced RGB graphic input signals
l Input signal ranges from 0.55-0.9v
l Provides RGB analog gain and offset control
l Support 64 steps (one cycle of pixel)of phase adjust
l ADC sampling rates are up to 110MHZ for x type, 160MHZ for E type Supports analog SOG
input
2. YUV Front End
l Support ITU-R BT.656 8-bit input
l Built-in YUV to RGB color space converter
3. Display
l Supports data swap to fit any panel data alignment for PCB Layout
l Built in LVDS transmitter
l Supports spectrum of output clock
4. Hot interface
l Support serial 2-wire IIC bus
l Provides 2 channel PMW
5. Power
l Power supply
l Less than 1.3W
ViewSonic Corporation Confidential - Do Not CopyQ7b-3
19
6. Video processor
l Flexible de-interlacing unit for VGA and digital YUV video input data
l Auto-calibration function for quick vide cantering, clock adjust and phase adjust
l Independent horizontal and vertical zoom in/out algorithm
l Enhanced interpolation algorithm for optimal image quality
l Provides RGB digital gain and offset control
l Dithering function supports 24-bits quality for 18-bit panel
l SRGB matrix mapping support
l 10-bit programmable gamma table for panel compensation
l Supports Hue and saturation adjustment
l Built-in POST pattern
Timing controller
l Support RSDS output
l Provides 4 differential data pairs to support 6 or 8-bit RGB data bus
l 10 General Purpose output allow suitability to different production environments
l Provide single pixel (18-24-bit) or dual pixel (36-48-bit)
l Programmable RSDS swing level
l Supports line offset function for two bank system panel
l 12 GPO internal controls 10 GPO external pin outputs
l Supports data swap to fit any panel data alignment for PCD layout
Sync Processor
l Supports separate, composite and TTL-level sync-on-Green (SOG) sync input
l Polarity detection for HSYNCI and VSYNCI
l Fast mode change detection function
ViewSonic Corporation Confidential - Do Not CopyQ7b-3
20
Pin description
ViewSonic Corporation Confidential - Do Not CopyQ7b-3
21
ViewSonic Corporation Confidential - Do Not CopyQ7b-3
22
C.NT68521
The NT68521 is a high quality image and highly integrated LCD controller, it combines a triple ADC, scaling engine,
OSD, LVDS and timing controller
The ADC supporter up to 160MHZ pixel rate and built-in a low jitter digital for sampling input video that provides
more stabile ,clear data for display,
The NT68521 Built-in DSP engine execute image zoom-in, zoom out function, the zoom feature provides linear
scaling up/down that makes it easier to fit different panel resolutions
The OSD provides a bit map,multi-color RAM front that is more flexible to create the customer’s OSD the output
provides multi-interface and for general panel solutions ,the display provides LVDS interface
The NT68521 also has a built-in spread spectrum feature to provide low EMI solutions ,SRGB for video color space
convert ,post pattern for manufacturing test ,de-interlace feature receives interlace video input and display on TFT
panels
ViewSonic Corporation Confidential - Do Not CopyQ7b-3
23
5. Adjustment Procedure
210mm
LCD Module
Optical
Black P
asteboard Cylinder
1. Function test
1.1 products
17” LCD Monitor
1.2 test equipment
(2-1). One PC (Windows system);two RS-232 PORT,COM1: signal resolution、COM2: color
meter。
Print PORT: connection with IIC/RS-232 Adapter Board
(2-2).Color Meter: MINOLTA. CA-110 is 21cm apart form the screen (eg: BM-7 distance is 50cm;
Field = 2.0)
(2-3). IIC/RS-232 Adapter Board (Set IIC Port)
(2-4). (TOPCON BM-7 or CA110) will be upright with Monitor
(2-5).each equipment’ s connection circuit diagram, pls see the appendix two and three.
(3).Setup
( 3-1 ).with 32 level gray scale Pattern
(3- 2 ).Brightness Set 50; Contrast Set 50.
( 3-3 ). Auto White Balance:
Entered into Maintain mode then choose Menu (F199N) Icon ,and press (+) Key to enter
into Maintain Menu; choose Auto Color ,press down (+) Key to implement Auto Color
Adjust。
(4).adjust specification:
At Brightness=50, Contrast=50 Full White Pattern
6500°K: x=0.313±0.015;y=0.329±0.015
9300°K: x=0.283±0.015;y=0.297±0.015
MINOLTA CA-110
S RGBK : x=0.313±0.015;y=0.329±0.015
Brightness=50,Contrast=50 Full White 180 CD/M≧
(5). Applicable program exercitation (use the color temperature adjust program to adjust color
temperature)
ViewSonic Corporation Confidential - Do Not CopyQ7b-3
24
2
(5- 1).WBA.exe, enter the pattern as follow:
(5- 2 ).at this time .pls press the open document as follow, choose the project document and
press the open button, the pattern is as follow
note: pls choose the related program depending on the model and panel of the product
( 5-3 ).pls choose” (Set)”à”Communication”, should alter the communication setup,the patter is
As follow:
ViewSonic Corporation Confidential - Do Not CopyQ7b-3
25
( 5-4 ). Pls select” Set”à”Range”, ADC setup range, pattern is as follow:
LM1901XXND: Gain 0 ~ 255 Offset 0 ~ 255
ViewSonic Corporation Confidential - Do Not CopyQ7b-3
26
(5-5 ). Pls select”(Set)”à”Color Temperature” setup the color temperature specification, the
7500K of the program is”SRGB”color temperature ,pattern as follow: advise the adjust
tolerance will be ±3
( 5-6 ). Pls select” Set”à”Color Analyzer” setup color analysis fixture Type,at present we can
Use CA-110 and BM-7. Chroma7120,the pattern as follow:
ViewSonic Corporation Confidential - Do Not CopyQ7b-3
27
( 5-7 ). Pls select” Set”à”Video Generator” to set the signal generator’ s Type and
Timing/Pattern, refer to the pattern as follow:
( 5-8 ) pls select ”Set”à”Default RGB Gain
ViewSonic Corporation Confidential - Do Not CopyQ7b-3
28
( 5-9 ). Begin to adjust;pls press the tools menu Icon, Icon, at this time the program will
go on the color temperature adjusting, refer to the pattern as follow.
(6).when adjusting the color tempreture,after the auto adjust, you must save the document and
then turn
On the machine, test the color and temperature:
6500°K: x=0.313±0.015;y=0.329±0.015
9300°K: x=0.283±0.015;y=0.297±0.015
SRGB : x=0.313±0.015;y=0.329±0.015
(7).POWER SAVING& power test﹕INPUT 1280x1024 @75Hz FULL WHITE, insert the signal
to D-SUB&DVI . CHECK whether the POWER SAVING is normal, POWER SAVING LED
whether the dark orange light is normal and the power is within the specification.
Power Board + Inverter Board 2nd Source
Power Board + Inverter Board for Innolux Panel
Base Assembly
Front Panel - Bezel Black
RGB Cable 30A 15 Pin to 2* Pin For All Panels Except CM
Blank Label LM/MONITO
Safety Label LM/F1704 L80.5*W60.5mm
LCD Module - SVA Panel 17" Lead Fre
Bracket - Black Rev. 1
Craft Box
GENERIC FOAM SET
GENERIC BOX
Panel Cover - Housing RGB +Audio
Remark 1:
Above listed items are examples, supplier can expand the rows to add more necessary items.
Remark 2: All revised RSPLs with newly added items or any change made should be highlighted and correlated with the ECN/ECR approved by ViewSonic Corporation. This is to
eliminate repeated cross checks of each item between this version and prior version
Description
)B-00005755
Added on 10/19/06B-00008140 XLM1704040002
Added on 10/19/06B-00008141 XLM1704050002
Added on 10/19/06B-00008128 XLM1700390004
Added on 10/19/06B-00008142 XLM1700390015-SH
ECN No. MN0605005XLMLM02280001
on 10/19/2006
ECN No. MN0605021P727AF26LM020-C
on 10/19/06
Added on 10/19/06CB-00008050 W0330715AQ261
Part on 08/15/06F102506170404
Added on 10/19/06E-00008101 E34S22170S001-B
ECN No. MN0608053XLM1704200003
on 10/19/06
ECN No. MN0609027XLM1704110002
on 10/19/06
A-00005760
C-00005778
C-00005783
DC-00005754
DC-00008045
HW-00005776
P-00005779 F400717170401
P-00001347 30833
P-00002515 20653
PL-00005775
W40218A022631
XLMF179040001
XLM1704280001
P727AF26LM021-
F103010LM0001
F102506170405
XLM1704200004
XLM1704110004
ViewSonic Corporation Confidential - Do Not CopyQ7b-3
Blank Label LM/MONITOR L43*W10m
Blank Label LM/MONITOR L85*W24m
POLYETHYLENE-L EPS LM/F179 L410*W120*H145m
POLYETHYLENE-R EPS LM/F179 L410*W120*H145m
PLASTIC BAG PE L610*W510*T0.04m
PLASTIC BAG PE L260*W180*T0.03m
PEARL BGA EPE L320*W200*T1.0mm FOR LM190
CARTON B LM/LM1704 L430*W125*H437m
PARTITION SUPPORTBC LM/MONITOR L800*W50*H50*T5m
PARTITION SUPPORTBC LM/MONITOR L1800*W50*H50*T5m
LM/LM1704 L1040*W432*H60m
LM/LM1704 L1170*W865*H60m
LM/LM1704 L1040*W865*H60m
PALLET SMOKE WOOD LM/F179 L1180*W870*H120m
PALLET SMOKE WOOD LM/F179 L1050*W430*H120n
PALLET SMOKE WOOD LM/F179 L1050*W870*H120m
PE LIMPID W500*T0.03mm 1500
PACKTHREAD PP WHITE W14.5mm*T0.8mm 1300
SCREW MACHINE STEEL 十/B Φ3.0* L4mm NICKE
SCREW MACHINE/STEEL 十/TΦ4xL8mm NICKE
SCREW MACHINE BINDING Φ4.0*L5mm NICKEL with toothed lock washer
SCREW MACHINE/ Φ3*L6mm NI NICKE
SCREW 十/B Φ3.0*L10mm NICKEL(R70GB-3010600
Bracket SECC LM/LM1704(RGB CABEL) FOR ViewSonic REV:
anel bracket-L F179 SECC T=0.8m
anel bracket-R F179 SECC T=0.8m
MYLAR L136*W124*T0.188m
MYLAR L350 X W290 X T0.12M
SPEAKER SPONGE L15*W10*T7.0m
SPEAKER SPONGE L52.5*W41*T15mm EVA 25° FOR LM170
RUBBER CUSHION Φ12*H23.5m
RUBBER CUSHION /RUBBER L15*W8*T9.8mm BLACKL15*8*9.8 BLAC
(EVA) L15mm*W10mm*H11mm WITH ADHESIV
COVER(HINGE) ABS PA757 C LM/LM1704 (L143*W27.5*H25mm) REV:
BEZEL ABS PA757 BLACK C LM/LM1704 FOR ViewSonic REV:
FUNCTION-KEY F1704 ABS HB BLACKLENS PMMA NATURAL LM/LM1704&1904 REV:
GLUE 50g/BOTTLE (﹕-60℃~+200℃)
ADHESIVE TAPE L25000*W15*T0.25mm 25m/ROLL(YW0910300002
L50000*W8*T0.1mm (YW0911200007
L75m*W48*T 0.045mm FOR VIWESONI
AL FOIL L100xW40xT0.07m
AL FOILL100xW30*T0.35mm(Y78400004G*1
AUDIO CABIE 26AWG UL2547 L=1800mm 6C BLAC
RGB CABLE 30AWG UL20276 L1500mm 15PIN TO 2*8PIN BLACK
WIRE FFC CY050408001 P=1.0mm 30PIN L195mm HUNG F
WIRE FFC FFCC0605T2250EC P=1.0mm 8PIN L250m
POWER BOARD+INVERTER BOARD ASSY PI-SB03 +24V +5V (W- GROUND)
LM/17''/19'' LCD MONITOR FOR VIEWSONI
BARE PCB LM/17"&19"LCD(FOR VIEWSONIC) POWER+INVERTER BOARD
1SIDE CEM-1 T1.6mm REV:1.0
MAIN BOARD ASSY LM/F1704/F1904 ( 2 sides FR-4 T1.6mm REV:1.0
IC EEPROM AT24C16 2500ns ATMEL SOIC-8 2K*8 (SMD)U4
IC Linear voltage converter AP1117E18A SOT-223- 3Pin(SMD
VOLTAGE REGULATOR LD1117-18-A SOT-223 3PIN 1.8V UTC (SMD)
IC LINEAR IC VOLTAGE REGULATOR GL1117A-3.3 (INPUT 4.8~12V
OUTPUT 3.3V) SOT-223 GTM LeadFree (SMD)
LINEAR IC AUDIO AMPLIFIER APA2068KAI SOP-16 ANPEC LEAD FREE
(SMD)
IC MCU MTV512GMG 64K MYSON LQFP-48P Lead Free (SMD)U3
IC ASIC/SCALER RTD2023LPLCC-48P REALTEK Lead Free(SMD
PCB printing LM/F1704/F1904 FOR mainboard 2sides FR-4 T1.6mm REV:1.
CAP MLCC /NPO 12PF 50V±5%(J) 0603 TAPPING (SMD)C26
CAP MLCC /NPO 22PF 50V±5%(J) 0603 TPPING (SMD)C25
CAP MLCC X5R 1uF 16V ±10%(K) 0603 TAPING (SMD)CA5 CA6 CA
CAP MLCC Y5V 0.47uF 16V±20%(M) 0603 TAPPING (SMD)C33
CAP EC(S) -40~105℃ 10uF 25V ±20% (M) Φ5×H7mm P=2.5mm (DIP
CAP EC –40~105℃100uF/16V ±20%(M) Φ6.3×H P=2.5mm (DIP)
CAP EC -40~105℃ 22UF/16V ±20%(M) ∮5*H5MM P=2.0MM(DIP)
anel bracket-R F179 SECC T=0.8m
MYLAR L136*W124*T0.188m
MYLAR L350 X W290 X T0.12M
SPEAKER SPONGE L15*W10*T7.0m
SPEAKER SPONGE L52.5*W41*T15mm EVA 25° FOR LM170
RUBBER CUSHION Φ12*H23.5m
(EVA) L15mm*W10mm*H11mm WITH ADHESIV
BEZEL ABS PA757 BLACK C LM/LM1704 FOR ViewSonic REV:
FUNCTION-KEY F1704 ABS HB BLACKLENS PMMA NATURAL LM/LM1704&1904 REV:
GLUE 50g/BOTTLE (﹕-60℃~+200℃)
ADHESIVE TAPE L25000*W15*T0.25mm 25m/ROLL(YW0910300002
L50000*W8*T0.1mm (YW0911200007
L75m*W48*T 0.045mm FOR VIWESONI
AL FOIL L50×W30×T0.10m
AL FOIL L100xW40xT0.07m
AL FOILL100xW30*T0.35mm(Y78400004G*1
AUDIO CABIE 26AWG UL2547 L=1800mm 6C BLAC
RGB CABLE 30AWG UL20276 L1500mm 15PIN TO 2*8PIN BLACK
(CON).POWER CORD/AC UL18AWG L1500mmBLACK.C.I-SHENG125V
10A....
WIRE FFC CY050408001 P=1.0mm 30PIN L195mm HUNG F
WIRE FFC FFCC0605T2250EC P=1.0mm 8PIN L250m
POWER BOARD+INVERTER BOARD ASSY PI-SB03 +24V +5V (WGROUND) LM/17''/19'' LCD MONITOR FOR VIEWSONI
BARE PCB LM/17"&19"LCD(FOR VIEWSONIC) POWER+INVERTER
BOARD 1SIDE CEM-1 T1.6mm REV:1.0
MAIN BOARD ASSY LM/F1704/F1904 ( 2 sides FR-4 T1.6mm REV:1.0
IC EEPROM AT24C16 2500ns ATMEL SOIC-8 2K*8 (SMD)U4
IC Linear voltage converter AP1117E18A SOT-223- 3Pin(SMD
IC LINEAR VOLTAGE REGULATOR AP1117E33A SOT-223 ANACHIP
(SMD)
IC LINEAR IC VOLTAGE REGULATOR GL1117A-3.3 (INPUT 4.8~12V
OUTPUT 3.3V) SOT-223 GTM LeadFree (SMD)
LINEAR IC AUDIO AMPLIFIER APA2068KAI SOP-16 ANPEC LEAD
FREE (SMD)
IC MCU MTV512GMG 64K MYSON LQFP-48P Lead Free (SMD)U3
IC ASIC/SCALER RTD2023LPLCC-48P REALTEK Lead Free(SMD
CAP MLCC NPO 10pF 50V ±5%0603 TAPPING (SMD)C15 C18 C22 C46 C47
CAP MLCC /NPO 12PF 50V±5%(J) 0603 TAPPING (SMD)C26
CAP MLCC /NPO 22PF 50V±5%(J) 0603 TPPING (SMD)C25
CAP MLCC X5R 1uF 16V ±10%(K) 0603 TAPING (SMD)CA5 CA6 CA
CAP MLCC Y5V 0.47uF 16V±20%(M) 0603 TAPPING (SMD)C33
F300250000070PLASTIC BAG PE L610*W510*T0.04mm 1
XLMLM02280001BASE ASSY LM/LM1702 FOR Atlantis1
F300483202001PEARL BGA EPE L320*W200*T1.0mm FOR LM19041
CARTON LM/LM1704 L428*W128*H438mm for Vosunis1
ViewSonic Corporation Confidential - Do Not CopyQ7b-3
PACKING PART LIST ( Q7b-3)
ViewSonic Model Number: VS11147
Rev: 1b
ItemViewSonic P/NRef. P/NDescriptionQ'ty
1N/AF400718170401CARTON LM/LM1704 L428*W128*H438mm for Vosunis1
2P-00005780F20133F179003POLYETHYLENE-L EPS LM/F179 L410*W120*H145mm1
3P-00005781F20143F179003POLYETHYLENE-R EPS LM/F179 L410*W120*H145mm1
4CB-00005758W0026918A0142AUDIO CABIE 26AWG UL2547 L=1800mm 6C BLACK1
5A-00005760W40218A022631CABLE(CON).POWER CORD/AC USA..18AWG L1500mm BLACK.C.1
6DC-00005774F000217043001USER'S MANUAL LM/LM1704 ENGLISH L210*W148mm REV:01
7N/AF300250000071PLASTIC BAG PE L260*W180*T0.03mm 1
8N/AMONITOR HEAD ONLY1
9P-00006586F300250000070PLASTIC BAG PE L610*W510*T0.04mm 1
10 C-00005778XLMLM02280001BASE ASSY LM/LM1702 FOR Atlantis1
11 N/AF300483202001PEARL BGA EPE L320*W200*T1.0mm FOR LM19041
61
9. Block Diagram
DDC_SCL
DDC_SDA
<Value>
DDC_VDD
DDC_SDA
MCU
VGA_DET
VGA_DET
DDC_VDD
G_IN
B_IN
HSI
VSI
VSI
HSI
B_IN+
G_IN+
<Value>
G_IN
B_IN
HSI
VSI
DDC_SDA
DDC_SCL
DDC_SCL
DDC_VDD
VGA_DET
VGA_IN
R_IN
R_IN+
Scaler
R_IN
MUTE
AMP_STBY
VOLUME
<Value>
12V
Audio
<Value>
MUTE
AMP_STBY
VOLUME
<Value>
SDA
SCL
Key_BUS
Key
Key_BUS
12V
<Value>
12V
Power
5V
SCL
<Value>
SCL
5VA 3.3V
SDA
SDA
SDA
SCL
RXCK+/-
RX0+/-
RX1+/-
RX2+/-
RX3+/-
EEPROM
<Value>
RX3+/-
RXCK+/-
RX2+/-
RX1+/-
Panel Interface
RX0+/-
3.3V
1.8V
PANEL_VCC1.8V
PANEL_VCC
ViewSonic Corporation Confidential - Do Not CopyQ7b-3
Thank you in advance for your feedback on our Service Manual, which allows continuous improvement
of our products. We would appreciate your completion of the Assessment Matrix below, for return to
ViewSonic Corporation.
Assessment
A. What do you think about the content of this Service Manual?
Unit Excellent Good Fair Bad
1. Precautions and Safety Notices
2. Specification
3. Front Panel Function Control Description
4. Circuit Description
5. Adjustment Procedure
6. Troubleshooting Flow Chart
7. Recommended Spare Parts List
8. Exploded Diagram and Exploded Parts List
9. Block Diagrams
10. Schematic Diagrams
11.PCB Layout Diagrams
B. Are you satisfied with this Service Manual?
Item Excellent Good Fair Bad
1. Service Manual Content
2. Service Manual Layout
3. The form and listing
C. Do you have any other opinions or suggestions regarding this service manual?
Reader’s basic dada:
Name:
Title:
Company:
Add:
Tel:
Fax:
E-mail:
After completing this form, please return it to ViewSonic Quality Assurance in the USA at facsimile
1-909-839-7943. You may also e-mail any suggestions to the Director, Quality Systems & Processes
(marc.maupin@viewsonic.com)
ViewSonic Corporation Confidential - Do Not CopyQ7b-3
77
Loading...
+ hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.