ViewSonic Pro8800WUL, Pro8530HDL, Pro8510L User Manual

Pro8510L/Pro8520WL/Pro8530HDL/ Pro8800WUL DLP Projector

User Guide

IMPORTANT: Please read this User Guide to obtain important information on installing and using your product in a safe manner, as well as registering your product for future service. Warranty information contained in this User Guide will describe your limited coverage from ViewSonic Corporation, which is also found on our web site at http://

ZZZYLHZVRQLFFRPLQ (QJOLVKRU LQ VSHFL¿FODQJXDJHV XVLQJ WKH 5HJLRQDOVHOHFWLRQ

box in the upper right corner of our website. “Antes de operar su equipo lea cu idadosamente las instrucciones en este manual”

Model No. VS16369/VS16370/ VS16371/VS16372

Compliance Information

FCC Statement

This device complies with part 15 of FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

y Reorient or relocate the receiving antenna. y Increase the separation between the equipment and receiver. y Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected.

y Consult the dealer or an experienced radio/TV technician for help.

Warning:<RXDUHFDXWLRQHGWKDWFKDQJHVRUPRGL¿FDWLRQVQRWH[SUHVVO\DSSURYHG

by the party responsible for compliance could void your authority to operate the equipment.

For Canada

CAN ICES-3 (B)/NMB-3(B)

CE Conformity for European Countries

The device complies with the EMC Directive 2014/30/EU and Low Voltage Directive 2014/35/EU.

Following information is only for EU-member states:

The mark is in compliance with the Waste Electrical and Electronic Equipment Directive 2012/19/EU (WEEE).

The mark indicates the requirement NOT to dispose the equipment including any spent or discarded batteries or accumulators as unsorted municipal waste, but use the return and collection systems available.

If the batteries, accumulators and button cells included with this equipment, display the chemical symbol Hg, Cd, or Pb, then it means that the battery has a heavy metal content of more than 0.0005% Mercury or more than,

0.002% Cadmium, or more than 0.004% Lead.

Important Safety Instructions

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this unit near water.

6. Clean with a soft, dry cloth.

7. Do not block any ventilation openings. Install the unit in accordance with the manufacturer’s instructions.

8. Do not install near any heat sources such as radiators, heat registers, stoves,

RURWKHUGHYLFHVLQFOXGLQJDPSOL¿HUVWKDWSURGXFHKHDW

9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade and the third SURQJDUHSURYLGHGIRU\RXUVDIHW\,IWKHSURYLGHGSOXJGRHVQRW¿WLQWR\RXU outlet, consult an electrician for replacement of the obsolete outlet.

10. Protect the power cord from being walked on or pinched particularly at plugs.

Convenience receptacles and the point where they exit from the unit. Be sure that the power outlet is located near the unit so that it is easily accessible.

 2QO\XVHDWWDFKPHQWVDFFHVVRULHVVSHFL¿HGE\WKHPDQXIDFWXUHU  8VHRQO\ZLWKWKHFDUWVWDQGWULSRGEUDFNHWRUWDEOHVSHFL¿HGE\

the manufacturer, or sold with the unit. When a cart is used, use caution when moving the cart/unit combination to avoid injury from tipping over.

13. Unplug this unit when unused for long periods of time.

 5HIHUDOOVHUYLFLQJWRTXDOL¿HGVHUYLFHSHUVRQQHO6HUYLFLQJLVUHTXLUHGZKHQWKH

unit has been damaged in any way, such as: if the power-supply cord or plug is damaged, if liquid is spilled onto or objects fall into the unit, if the unit is exposed to rain or moisture, or if the unit does not operate normally or has been dropped.

Declaration of RoHS2 Compliance

This product has been designed and manufactured in compliance with Directive 2011/65/EU of the European Parliament and the Council on restriction of the use of certain hazardous substances in electrical and electronic equipment (RoHS2 Directive) and is deemed to comply with the maximum concentration values issued by the European Technical Adaptation Committee (TAC) as shown below:

Substance

Lead (Pb) 0.1% < 0.1% Mercury (Hg) 0.1% < 0.1% Cadmium (Cd) 0.01% < 0.01% Hexavalent Chromium (Cr Polybrominated biphenyls (PBB) 0.1% < 0.1% Polybrominated diphenyl ethers (PBDE) 0.1% < 0.1%

) 0.1% < 0.1%

Proposed Maximum Concentration

Actual Concentration

Certain components of products as stated above are exempted under the Annex III of the RoHS2 Directives as noted below:

Examples of exempted components are:

1. 0HUFXU\LQFROGFDWKRGHÀXRUHVFHQWODPSVDQGH[WHUQDOHOHFWURGHÀXRUHVFHQW

lamps (CCFL and EEFL) for special purposes not exceeding (per lamp): (1) Short length (≦500 mm): maximum 3.5 mg per lamp. (2) Medium length (＞500 mm and ≦1,500 mm): maximum 5 mg per lamp. (3) Long length (＞1,500 mm): maximum 13 mg per lamp.

2. Lead in glass of cathode ray tubes.

3. /HDGLQJODVVRIÀXRUHVFHQWWXEHVQRWH[FHHGLQJE\ZHLJKW

4. Lead as an alloying element in aluminium containing up to 0.4% lead by weight.

5. Copper alloy containing up to 4% lead by weight.

6. Lead in high melting temperature type solders (i.e. lead-based alloys containing

85% by weight or more lead).

7. Electrical and electronic components containing lead in a glass or ceramic other

than dielectric ceramic in capacitors, e.g. piezoelectronic devices, or in a glass or ceramic matrix compound.

iii

Copyright © ViewSonic® Corporation, 2016. All rights reserved. Macintosh and Power Macintosh are registered trademarks of Apple Inc. Microsoft, Windows, Windows NT, and the Windows logo are registered trademarks of Microsoft Corporation in the United States and other countries. ViewSonic, the three birds logo, OnView, ViewMatch, and ViewMeter are registered trademarks of ViewSonic Corporation. VESA is a registered trademark of the Video Electronics Standards Association. DPMS and DDC are trademarks of VESA. PS/2, VGA and XGA are registered trademarks of International Business Machines Corporation. Disclaimer: ViewSonic Corporation shall not be liable for technical or editorial errors or omissions contained herein; nor for incidental or consequential damages resulting from furnishing this material, or the performance or use of this product. In the interest of continuing product improvement, ViewSonic Corporation reserves WKHULJKWWRFKDQJHSURGXFWVSHFL¿FDWLRQVZLWKRXWQRWLFH,QIRUPDWLRQLQWKLVGRFXment may change without notice. No part of this document may be copied, reproduced, or transmitted by any means, for any purpose without prior written permission from ViewSonic Corporation.

Product Registration

To fulfill possible future product needs, and to receive additional product information as it becomes available, please visit your region section on ViewSonic’s website to register your product online. The ViewSonic CD also provides an opportunity for you to print the product registration form. Upon completion, please mail or fax to a respective ViewSonic office. To find your registration form, use the directory “:\CD\Registration”. Registering your product will best prepare you for future customer service needs. Please print this user guide and fill the information in the “For Your Records” section. For additional information, please see the “Customer Support” section in this guide.

For Your Records

Product Name: Pro8510L/Pro8520WL/Pro8530HDL/Pro8800WUL

ViewSonic DLP Projector

Model Number: VS16369/VS16370/ VS16371/VS16372 Document Number: Pro8510L/Pro8520WL/Pro8530HDL/Pro8800WUL_UG_

ENG Rev

Serial Number: Purchase Date: ________________________________________

Product disposal at end of product life

The lamp in this product contains mercury which can be dangerous to you and the environment. Please use care and dispose of in accordance with local, state or federal laws. ViewSonic respects the environment and is committed to working and living green. Thank you for being part of Smarter, Greener Computing. Please visit ViewSonic website to learn more. USA & Canada: http://www.viewsonic.com/company/green/recycle-program/ Europe: http://www.viewsoniceurope.com/uk/support/recycling-information/ Taiwan: http://recycle.epa.gov.tw/recycle/index2.aspx

________________________________________

. 1A 04-14-16

Important safety

instructions .......................2

Introduction......................4

Projector features ................................. 4

Shipping contents.................................4

Controls and functions .........................5

Positioning your

projector..........................10

Choosing a location............................10

Projection dimensions........................ 11

Shifting the projection lens

vertically ............................................ 16

Connection ......................17

Connecting a computer or monitor ....19

Connecting Video source devices ...... 20

Playing sound through the projector .. 22

Using the cable management cover ... 23

Operation ........................24

Starting up the projector..................... 24

Using the menus................................. 25

Utilizing the password function ......... 26

Switching input signal........................ 28

Adjusting the projected image ........... 29

Magnifying and searching for

details ................................................. 31

Selecting the aspect ratio ...................32

Optimizing the image......................... 33

Setting the presentation timer ............36

Hiding the image................................37

Locking control keys.......................... 38

Creating your own startup screen....... 38

Operating in a high altitude

environment ....................................... 38

Using the CEC function..................... 39

Using the 3D functions...................... 39

Controlling the projector through

a LAN environment ........................... 40

Using the projector in standby mode. 47

Adjusting the sound ........................... 47

Shutting down the projector .............. 49

Menu operation.................................. 50

Maintenance ...................59

Care of the projector .......................... 59

Using the dust filter (optional

accessory) .......................................... 59

Lamp information.............................. 61

Troubleshooting .............64

Specifications ..................65

Dimensions ........................................ 65

Ceiling mount installation ................. 65

IR control table .................................. 66

RS232 command table....................... 67

Timing chart ...................................... 77

Projector specifications...................... 81

Important safety instructions

Your projector is designed and tested to meet the latest standards for safety of information technology equipment. However, to ensure safe use of this product, it is important that you follow the instructions mentioned in this manual and marked on the product.

Safety Instructions

1. Please read this manual before you operate your projector. Save it for future reference.

2. Do not look straight at the projector lens during operation. The intense light beam may damage your eyes.

3. Refer servicing to qualified service personnel.

4. Always open the lens shutter or remove the lens cap when the projector lamp is

on.

5. In some countries, the line voltage is NOT stable. This projector is designed to operate safely within a mains voltage between 100 to 240 volts AC, but could fail if power cuts or surges of ±10 volts occur. In areas where the mains voltage may fluctuate

or cut out, it is recommended that you connect your projector through a power stabilizer, surge protector or uninterruptible power supply (UPS).

6. Do not block the projection lens with any objects when the projector is under operation as this could cause the objects to become heated and deformed or even cause a fire. To temporarily turn off the lamp, press BLANK on the projector or remote control.

7. The lamp becomes extremely hot during operation. Allow the projector to cool for approximately 45 minutes prior to removing the lamp assembly for replacement.

8. Do not operate lamps beyond the rated lamp life. Excessive operation of lamps beyond the rated life could cause them to break on rare occasions.

9. Never replace the lamp assembly or any electronic components unless the projector is unplugged.

10. Do not place this product on an unstable cart, stand, or table. The product may fall, sustaining serious damage.

11. Do not attempt to disassemble this projector. There are dangerous high voltages inside which may cause death if you should come into contact with live parts. The only user serviceable part is the lamp which has its own removable cover.

Under no circumstances should you ever undo or remove any other covers. Refer servicing only to suitably qualified professional service personnel.

12. Do not place this projector in any of the following environments.

- Space that is poorly ventilated or confined. Allow at least 50 cm clearance from walls and free flow of air around the projector.

- Locations where temperatures may become excessively high, such as the inside of a car with all windows rolled up.

- Locations where excessive humidity, dust, or cigarette smoke may contaminate optical components, shortening the projector's life span and darkening the picture.

- Locations near fire alarms

- Locations with an ambient temperature above 40°C / 104°F

- Locations where the altitudes are higher than 3000 m (10000 feet).

13. Do not block the ventilation holes. If the ventilation holes are seriously obstructed, overheating inside the projector may result in a fire.

- Do not place this projector on a blanket, bedding or any other soft surface.

- Do not cover this projector with a cloth or any other item.

- Do not place inflammables near the projector.

14. Always place the projector on a level, horizontal surface during operation.

- Do not use if tilted at an angle of more than 10 degrees left to right, nor at angle of more than 15 degrees front to back. Using the projector when it is not fully horizontal may cause a malfunction of, or damage to, the lamp.

15. Do not stand the projector on end vertically. Doing so may cause the projector to fall over, causing injury or resulting in damage to the projector.

16. Do not step on the projector or place any objects upon it. Besides probable physical damage to the projector, doing so may result in accidents and possible injury.

17. Do not place liquids near or on the projector. Liquids spilled into the projector may cause it to fail. If the projector does become wet, disconnect it from the power supply's wall socket and call your local service center to have the projector serviced.

18. This product is capable of displaying inverted pictures for ceiling mount installation.

Use only qualified ceiling mount kit for mounting the projector and ensure it is securely installed.

19. When the projector is under operation, you may sense some heated air and odor from its ventilation grill. It is a normal phenomenon and not a product defect.

20. Do not use the Security bar for transporting or installation. It should be used with a commercially available theft prevention cable.

Warni ng

• THIS APPARATUS MUST BE EARTHED.

• When installing the unit, incorporate a readily accessible disconnect device in the fixed

wiring, or connect the power plug to an easily accessible socket-outlet near the unit. If a fault should occur during operation of the unit, operate the disconnect device to switch the power supply off, or disconnect the power plug.

Safety instructions for ceiling mounting of the projector

We want you to have a pleasant experience using your projector, so we need to bring this safety matter to your attention to prevent damage to person and property.

If you intend to mount your projector on the ceiling, we strongly recommend that you use a proper fitting projector ceiling mount kit and that you ensure it is securely and safely installed.

If you use an inappropriate projector ceiling mount kit, there is a safety risk that the projector may fall from the ceiling due to an improper attachment through the use of the wrong gauge or length screws.

You can purchase a projector ceiling mount kit from the place you purchased your projector. We recommend that you also purchase a separate security cable and attach it securely to both the anti-theft lock slot on the projector and the base of the ceiling mount bracket. This will perform the secondary role of restraining the projector should its attachment to the mounting bracket become loose.

Introduction

Projector features

The projector integrates high-performance optical engine projection and a user-friendly design to deliver high reliability and ease of use.

Some of the features may not be available on your projector. Actual performance may vary and subject to model specifications.

• Power saving function decreasing the power consumption of the lamp by up to 80%

when no input signal can be detected for a set period of time.

• Presentation timer for better control of time during presentations

•

LAN Settings allowing management of projector status from a remote computer

• Supports 3D display

•Color Management allowing color adjustments to your liking

• Less than 0.5W power consumption when power saving mode is turned on

• Screen Color correction allowing projection on surfaces of several predefined colors

• Quick auto search speeding up the signal detecting process

• Color modes providing choices for different projection purposes

• One-key auto-adjustment to display the best picture quality (only for analog signal)

• Digital keystone correction and 4 corner adjustment to correct distorted images

• Adjustable color management control for data/video display

• Ability to display 1.07 billion colors

• Multi-language On-Screen Display (OSD) menus

• Switchable normal and economic modes to reduce the power consumption

• Component HDTV compatibility (YP

• HDMI CEC (Consumer Electronics Control) function allows synchronized power ON/

OFF operation between the projector and a CEC-compatible DVD player device connected to the HDMI input of the projector

The apparent brightness of the projected image will vary depending on the ambient lighting conditions, selected input signal contrast/brightness settings, and is directly proportional to projection distance.

The lamp brightness will decline over time and may vary within the lamp manufacturers specifications. This is normal and expected behavior.

bPr)

Shipping contents

1. Projector

2. Power Cord

3. Multi-language User Manual CD

4. Quick Start Guide

5. Remote Control & Batteries

6. VGA Cable

7. Cable management cover

8. Replacement lamp (optional)

9. Soft carry case (optional)

10. VGA-Component adapter (optional)

11. Dust filter (optional)

Controls and functions

Lens shift wheel

Focus and Zoom rings

Power indicator light

Lamp indicator light

Temperature indicator light

Projector

•Power

Toggles the projector between standby mode and Power ON.

HDMI/MHL port indicator

Lights up blue when an HDMI or MHL device is inserted into the inner HDMI/ MHL port.

• / / / (Keystone keys)

Manually corrects distorted images resulting from an angled projection.

• Left/ Right/ Up/ Down

Selects the desired menu items and makes adjustments.

•Menu

Turns on the On-Screen Display (OSD) menu.

•Exit

Goes back to previous OSD menu, exits and saves menu settings.

•Enter

Enacts the selected On-Screen Display (OSD) menu item.

•

Displays the Corner Adj. page.

•Color Mode

Selects an available picture setup mode.

• Source

Displays the source selection bar.

• (Help)

Displays the HELP menu by a long press for 3 seconds.

Remote control

Powe r

To use the remote mouse control keys (Page Up, Page Down, , and

"Using the remote mouse control" on page 8 for details.

•Power

Toggles the projector between standby mode and Power ON.

•COMP

Selects source from Computer In port for display.

•HDMI/MHL

Selects source from HDMI/MHL port for display.

•VIEDO

Selects VIEDO source for display.

• Auto Sync

Automatically determines the best picture timings for the displayed image.

Power

COMP

Auto

Sync

Menu Exit

Mouse

Blank

Eco

Mode

), see

HDMI

VIDEO

/MHL

Source

Enter

PgUp

PgDn

Pattern

Color

Audio Mode

Mode

• / / / (Keystone keys)

Manually corrects distorted images resulting from an angled projection.

•Enter

Enacts the selected On-Screen Display (OSD) menu item.

•

Displays the Corner Adj. page.

•Menu

Turns on the On-Screen Display (OSD) menu.

• Left/ Right/ Up/ Down

Selects the desired menu items and makes adjustments.

•Mouse

Switches between the normal and mouse modes.

PgUp, PgDn, , : active after pressing Mouse. An icon appears on the screen to

indicate the activation of the mouse mode.

Only available when a PC input signal is selected.

• (Left mouse button)

Performs the same function as the left mouse button when the mouse mode is activated.

Only available when a PC input signal is selected.

• (Right mouse button)

Performs the same function as the right mouse button when the mouse mode is activated.

Only available when a PC input signal is selected.

• (Aspect Ratio)

Displays the aspect ratio selection bar.

•Blank

Hides the screen picture.

• (Panel Key Lock)

Activates panel key lock. To unlock the

panel keys, press

• (My Button)

Allows user to define a short cut key on the remote control, and the function item is selected in OSD menu.

• Source

Displays the source selection bar.

•Laser

Emits visible laser pointer light for presentation purposes.

•Exit

Exits and saves menu settings.

• PgUp (Page Up)/PgDn (Page Down)

Operates your display software program (on a connected PC) which responds to page up/down commands (like Microsoft PowerPoint) when the mouse mode is activated.

Only available when a PC input signal is selected.

• Pattern

Displays embedded test pattern.

• (Mute)

Toggles the projector audio between on and off.

• (Help)

Displays the HELP menu.

• (Volume Up)

Increases the volume level.

• (Presentation Timer)

Displays the presentation timer settings menu.

•Eco Mode

Selects a lamp mode.

• (Volume Down)

Decreases the volume level.

• (Zoom)

Displays the zoom bar that magnifies or reduces the projected picture size.

•Color Mode

Selects an available picture setup mode.

• Audio Mode

Selects an audio mode.

Operating the LASER pointer

The Laser Pointer is a presentation aid for professionals. It emits colored light when you press it. The laser beam is visible. It is necessary to press and hold Laser for continuous output.

Do not look into the laser light window or shine the laser light beam on yourself or others. See the warning messages on the back of the remote control prior to using it.

The laser pointer is not a toy. Parents should be mindful of the dangers of laser energy and keep this remote control out of the reach of children.

Remote control code

The projector can be assigned to 8 different remote control codes, 1 to 8. When several adjacent projectors are in operation at the same time, switching the remote control codes can prevent interference from other remote controls. Set the remote control code for the projector first before changing that for the remote control.

To switch the code for the projector, select from among 1 to 8 in the SYSTEM > Remote Control Code menu.

To switch the code for the remote control, press ID set and the number button corresponding to the remote control code set in the projector OSD together for 5 seconds or more. The initial code is set to 1. When the code is switched to 8, the remote control can control every projector.

If different codes are set on the projector and remote control, there will be no response from the remote control. When that happens, a message will display to remind you to switch the code for the remote control.

Using the remote mouse control

The capability of operating your computer with the remote control gives you more flexibility when delivering presentations.

1. Set the input signal to a PC signal.

2. Press Mouse on the remote control. A cursor appears on the screen. You can press /

/ / to move the cursor for indication.

3. Press Mouse again to switch to the normal mode.

If you wish to use a more advanced mouse mode, follow the below steps:

1. Connect the projector to your PC or notebook with a USB cable prior to using the remote control in place of your computer’s mouse. See "Connecting a computer" on

page 19 for details.

2. Press Mouse to switch to the mouse mode. An icon appears on the screen to indicate the activation of the mouse mode.

3. Perform the desired mouse controls on your remote control.

• To move the cursor on the screen, press / / / .

• To left-click, press .

• To right-click, press .

• To operate your display software program (on a connected PC) which responds to

page up/down commands (like Microsoft PowerPoint), press PgUp/PgDn.

• To return to the normal mode, press Mouse again or other keys except for the

0°

mouse related multi-function keys.

Remote control effective range

Refer to the illustration about the location of the InfraRed (IR) remote control sensor(s). The remote control must be held at an angle within 30 degrees perpendicular to the projector's IR remote control sensor(s) to function correctly. The distance between the remote control and the sensor(s) should not exceed 8 meters (~ 26 feet).

Make sure that there are no obstacles between the remote control and the IR sensor(s) on the projector that might obstruct the infra-red beam.

Replacing the remote control batteries

1. To open the battery cover, turn the remote control over to view its back, press on the finger grip on the cover and slide it down in the direction of the arrow as illustrated.

2. Remove any existing batteries (if necessary) and install two AAA batteries observing the battery polarities as indicated in the base of the battery compartment. Positive (+) goes to positive and negative (-) goes to negative.

3. Refit the cover by aligning it with the base and pushing it back down into position. Stop when it clicks into place.

WARNING

• Avoid leaving the remote control and batteries in an excessive heat or humid environment

like the kitchen, bathroom, sauna, sunroom or in a closed car.

• Replace only with the same or equivalent type recommended by the battery manufacturer.

• Dispose of the used batteries according to the manufacturer's instructions and local

environment regulations for your region.

• Never throw the batteries into a fire. There may be danger of an explosion.

• If the batteries are drained or if you will not be using the remote control for an extended

period of time, remove the batteries to avoid damage to the remote control from possible battery leakage.

Positioning your projector

Choosing a location

Your room layout or personal preference will dictate which installation location you select. Take into consideration the size and position of your screen, the location of a suitable power outlet, as well as the location and distance between the projector and the rest of your equipment.

Your projector is designed to be installed in one of the following possible installation locations:

1. Front Table

Select this location with the projector placed near the floor in front of the screen. This is the most common way to position the projector for quick setup and portability.

2. Front Ceiling

Select this location with the projector suspended upside-down from the ceiling in front of the screen.

Purchase the projector ceiling mount kit from your dealer to mount your projector on the ceiling.

Set Front Ceiling in the SYSTEM > Projector

Position menu after you turn the projector on.

3. Rear Ceiling

Select this location with the projector suspended upside-down from the ceiling behind the screen.

Note that a special rear projection screen and the projector ceiling mounting kit are required for this installation location.

Set Rear Ceiling in the SYSTEM > Projector

Position menu after you turn the projector on.

4. Rear Table

Select this location with the projector placed near the floor behind the screen.

Note that a special rear projection screen is required.

Set Rear Table in the SYSTEM > Projector Position menu after you turn the projector on.

Projection dimensions

(a)

(d)

(b)

(e)

(f)

(c)

(a)

(d)

(c)

(b)

(e)

(f)

(a)

(c)

(b)

(e)

(f)

(d)

(f): Center of lens(e): Screen

• 4:3 image on a 4:3 screen

• 4:3 image on a 16:10 screen

(a)

(d)

(c)

(b)

(e)

(f)

The "screen" mentioned below refers to the projection screen usually consisting of a screen surface and a support structure.

Please see "Projector specifications" on page 81 for the native display resolution of this projector.

For models with a 4:3 native aspect ratio

When the projector’s native resolution is XGA (1024 x 768) with a throw ratio of 1.41~2.25

(a) Screen Size

[inch (cm)]

60 (152) 1.7 (67) 2.7 (107) 91 (36) 6.9 (2.7) 13.7 (5.4)

70 (178) 2.0 (78) 3.2 (124) 107 (42) 8.0 (3.2) 16.0 (6.3)

80 (203) 2.3 (89) 3.6 (142) 122 (48) 9.1 (3.6) 18.3 (7.2)

90 (229) 2.5 (100) 4.1 (160) 137 (54) 10.3 (4.1) 20.6 (8.1)

100 (254) 2.58 (111) 4.5 (178) 152 (60) 11.4 (4.5) 22.9 (9.0)

110 (279) 3.1 (122) 5.0 (195) 168 (66) 12.6 (5.0) 25.1 (9.9)

120 (305) 3.4 (133) 5.4 (213) 183 (72) 13.7 (5.4) 27.4 (10.8)

130 (330) 3.7 (144) 5.9 (231) 198 (78) 14.9 (5.9) 29.7 (11.7)

140 (356) 3.9 (155) 6.3 (249) 213 (84) 16.0 (6.3) 32.0 (12.6)

150 (381) 4.2 (167) 6.8 (267) 229 (90) 17.1 (6.8) 34.3 (13.5)

4:3 image on a 4:3 Screen

(b) Projection distance [m (inch)]

min. max. min. max.

[cm (inch)]

(d) Vertical offset

[cm (inch)]

4:3 image on a 16:10 Screen

(a)

(c)

(b)

(e)

(f)

(d)

(a)

(c)

(b)

(e)

(f)

(d)

(f): Center of lens(e): Screen

• 16:10 image on a 16:10 screen

• 16:10 image on a 4:3 screen

(a)

(d)

(c)

(b)

(e)

(f)

(a) Screen Size

[inch (cm)]

(b) Projection distance [m (inch)]

min. max. min. max.

[cm (inch)]

60 (152) 1.5 (59) 2.4 (94) 81 (32) 6.1 (2.4) 12.1 (4.8)

70 (178) 1.7 (69) 2.8 (110) 94 (37) 7.1 (2.8) 14.1 (5.6)

80 (203) 2.0 (78) 3.2 (126) 108 (42) 8.1 (3.2) 16.2 (6.4)

90 (229) 2.2 (88) 3.6 (141) 121 (48) 9.1 (3.6) 18.2 (7.2)

100 (254) 2.5 (98) 4.0 (157) 135 (53) 10.1 (4.0) 20.2 (7.9)

110 (279) 2.7 (108) 4.4 (173) 148 (58) 11.1 (4.4) 22.2 (8.7)

120 (305) 3.0 (118) 4.8 (188) 162 (64) 12.1 (4.8) 24.2 (9.5)

130 (330) 3.2 (128) 5.2 (204) 175 (69) 13.1 (5.2) 26.3 (10.3)

140 (356) 3.5 (137) 5.6 (220) 188 (74) 14.1 (5.6) 28.3 (11.1)

150 (381) 3.7 (147) 6.0 (235) 202 (79) 15.1 (6.0) 30.3 (11.9)

For models with a 16:10 native aspect ratio

(a)

(c)

(d)

(d) Vertical offset

[cm (inch)]

(e)

(f)

(b)

When the projector’s native resolution is WXGA (1280 x 800) with a throw ratio of 1.12~1.8

16:10 image on a 16:10 Screen

(a) Screen Size

[inch (cm)]

60 (152) 1.4 (57) 2.3 (91) 81 (32) 4.0 (1.6) 6.1 (2.4)

70 (178) 1.7 (67) 2.7 (106) 94 (37) 4.7 (1.9) 7.1 (2.8)

80 (203) 1.9 (76) 3.1 (122) 108 (42) 5.4 (2.1) 8.1 (3.2)

90 (229) 2.2 (86) 3.5 (137) 121 (48) 6.1 (2.4) 9.1 (3.6)

100 (254) 2.4 (95) 3.9 (152) 135 (53) 6.7 (2.6) 10.1 (4.0)

110 (279) 2.7 (105) 4.2 (167) 148 (58) 7.4 (2.9) 11.1 (4.4)

120 (305) 2.9 (114) 4.6 (182) 162 (64) 8.1 (3.2) 12.1 (4.8)

130 (330) 3.1 (124) 5.0 (198) 175 (69) 8.8 (3.4) 13.1 (5.2)

140 (356) 3.4 (133) 5.4 (213) 188 (74) 9.4 (3.7) 14.1 (5.6)

150 (381) 3.6 (143) 5.8 (228) 202 (79) 10.1 (4.0) 15.1 (6.0)

(a) Screen Size

[inch (cm)]

60 (152) 1.4 (54) 2.2 (86) 76 (30) 3.8 (1.5) 5.7 (2.3)

70 (178) 1.6 (63) 2.6 (100) 89 (35) 4.4 (1.8) 6.7 (2.6)

80 (203) 1.8 (72) 2.9 (115) 102 (40) 5.1 (2.0) 7.6 (3.0)

90 (229) 2.0 (81) 3.3 (129) 114 (45) 5.7 (2.3) 8.6 (3.4)

100 (254) 2.3 (90) 3.6 (143) 127 (50) 6.4 (2.5) 9.5 (3.8)

110 (279) 2.5 (99) 4.0 (158) 140 (55) 7.0 (2.8) 10.5 (4.1)

120 (305) 2.7 (108) 4.4 (172) 152 (60) 7.6 (3.0) 11.4 (4.5)

130 (330) 3.0 (117) 4.7 (186) 165 (65) 8.3 (3.3) 12.4 (4.9)

140 (356) 3.2 (126) 5.1 (201) 178 (70) 8.9 (3.5) 13.3 (5.3)

150 (381) 3.4 (134) 5.5 (215) 191 (75) 9.5 (3.8) 14.3 (5.6)

(b) Projection distance [m (inch)]

min. max. min. max.

(b) Projection distance [m (inch)]

min. max. min. max.

[cm (inch)]

16:10 image on a 4:3 Screen

[cm (inch)]

(d) Vertical offset

[cm (inch)]

(d) Vertical offset

[cm (inch)]

When the projector’s native resolution is WUXGA (1920 x 1200) with a throw ratio of 1.07~1.71

16:10 image on a 16:10 Screen

(a) Screen Size

[inch (cm)]

60 (152) 1.4 (54) 2.2 (87) 75 (29) 1.9 (0.7) 3.7 (1.5)

70 (178) 1.6 (63) 2.6 (101) 87 (34) 2.2 (0.9) 4.4 (1.7)

80 (203) 1.8 (72) 2.9 (116) 100 (39) 2.5 (1.0) 5.0 (2.0)

90 (229) 2.1 (81) 3.3 (130) 112 (44) 2.8 (1.1) 5.6 (2.2)

100 (254) 2.3 (91) 3.7 (145) 125 (49) 3.1 (1.2) 6.2 (2.5)

110 (279) 2.5 (100) 4.0 (159) 137 (54) 3.4 (1.3) 6.8 (2.7)

120 (305) 2.8 (109) 4.4 (174) 149 (59) 3.7 (1.5) 7.5 (2.9)

130 (330) 3.0 (118) 4.8 (188) 162 (64) 4.0 (1.6) 8.1 (3.2)

140 (356) 3.2 (127) 5.1 (203) 174 (69) 4.4 (1.7) 8.7 (3.4)

150 (381) 3.4 (136) 5.5 (217) 187 (74) 4.7 (1.8) 9.3 (3.7)

(a) Screen Size

[inch (cm)]

60 (152) 1.3 (51) 2.1 (82) 76 (30) 1.9 (0.8) 3.8 (1.5)

70 (178) 1.5 (60) 2.4 (96) 89 (35) 2.2 (0.9) 4.4 (1.8)

80 (203) 1.7 (68) 2.8 (109) 102 (40) 2.5 (1.0) 5.1 (2.0)

90 (229) 2.0 (77) 3.1 (123) 114 (45) 2.9 (1.1) 5.7 (2.3)

100 (254) 2.2 (85) 3.5 (137) 127 (50) 3.2 (1.3) 6.4 (2.5)

110 (279) 2.4 (94) 3.8 (150) 140 (55) 3.5 (1.4) 7.0 (2.8)

120 (305) 2.6 (102) 4.2 (164) 152 (60) 3.8 (1.5) 7.6 (3.0)

130 (330) 2.8 (111) 4.5 (178) 165 (65) 4.1 (1.6) 8.3 (3.3)

140 (356) 3.0 (120) 4.9 (191) 178 (70) 4.4 (1.8) 8.9 (3.5)

150 (381) 3.3 (128) 5.2 (205) 191 (75) 4.8 (1.9) 9.5 (3.8)

(b) Projection distance [m (inch)]

min. max. min. max.

(b) Projection distance [m (inch)]

min. max. min. max.

[cm (inch)]

16:10 image on a 4:3 Screen

[cm (inch)]

(d) Vertical offset

[cm (inch)]

(d) Vertical offset

[cm (inch)]

For models with a 16:9 native aspect ratio

(a)

(c)

(b)

(e)

(f)

(d)

(a)

(c)

(b)

(e)

(f)

(d)

(a)

(c)

(b)

(e)

(f)

(d)

(f): Center of lens(e): Screen

• 16:9 image on a 16:9 screen

• 16:9 image on a 4:3 screen

(a)

(d)

(c)

(b)

(e)

(f)

When the projector’s native resolution is 1080p (1920 x 1080) with a throw ratio of 1.07~1.71

(a) Screen Size

[inch (cm)]

60 (152) 1.4 (56) 2.3 (90) 75 (29) 5.6 (2.2) 11.2 (4.4)

70 (178) 1.7 (65) 2.7 (104) 87 (34) 6.5 (2.6) 13.1 (5.1)

80 (203) 1.9 (75) 3.0 (119) 100 (39) 7.5 (2.9) 14.9 (5.9)

90 (229) 2.1 (84) 3.4 (134) 112 (44) 8.4 (3.3) 16.8 (6.6)

100 (254) 2.4 (93) 3.8 (149) 125 (49) 9.3 (3.7) 18.7 (7.4)

110 (279) 2.6 (103) 4.2 (164) 137 (54) 10.3 (4.0) 20.5 (8.1)

120 (305) 2.8 (112) 4.5 (179) 149 (59) 11.2 (4.4) 22.4 (8.8)

130 (330) 3.1 (121) 4.9 (194) 162 (64) 12.1 (4.8) 24.3 (9.6)

140 (356) 3.3 (131) 5.3 (209) 174 (69) 13.1 (5.1) 26.2 (10.3)

150 (381) 3.6 (140) 5.7 (224) 187 (74) 14.0 (5.5) 28.0 (11.0)

16:9 image on a 16:9 Screen

(b) Projection distance [m (inch)]

min. max. min. max.

[cm (inch)]

(d) Vertical offset

[cm (inch)]

16:9 image on a 4:3 Screen

(a) Screen Size

[inch (cm)]

60 (152) 1.3 (51) 2.1 (82) 69 (27) 5.1 (2.0) 10.3 (4.1)

70 (178) 1.5 (60) 2.4 (96) 80 (32) 6.0 (2.4) 12.0 (4.7)

80 (203) 1.7 (68) 2.8 (110) 91 (36) 6.9 (2.7) 13.7 (5.4)

90 (229) 2.0 (77) 3.1 (123) 103 (41) 7.7 (3.0) 15.4 (6.1)

100 (254) 2.2 (86) 3.5 (137) 114 (45) 8.6 (3.4) 17.1 (6.8)

110 (279) 2.4 (94) 3.8 (151) 126 (50) 9.4 (3.7) 18.9 (7.4)

120 (305) 2.6 (103) 4.2 (164) 137 (54) 10.3 (4.1) 20.6 (8.1)

130 (330) 2.8 (111) 4.5 (178) 149 (59) 11.1 (4.4) 22.3 (8.8)

140 (356) 3.0 (120) 4.9 (192) 160 (63) 12.0 (4.7) 24.0 (9.5)

150 (381) 3.3 (128) 5.2 (205) 171 (68) 12.9 (5.1) 25.7 (10.1)

There is 3% tolerance among these numbers due to optical component variations. It is recommended that if you intend to permanently install the projector, you should physically test the projection size and distance using the actual projector in situ before you permanently install it, so as to make allowance for this projector's optical characteristics. This will help you determine the exact mounting position so that it best suits your installation location.

(b) Projection distance [m (inch)]

min. max. min. max.

[cm (inch)]

(d) Vertical offset

[cm (inch)]

Shifting the projection lens vertically

The vertical lens shift control provides flexibility for installing your projector. It allows the projector to be positioned slightly above or below the top level of the projected images.

Use the wheel to shift the projection lens upwards or downwards within the allowable range depending on your desired image position.

To use the lens shift wheel:

Turn the wheel to adjust the projected image position.

Do not over-tighten the wheel.

Lens shift adjustment does not result in a degraded picture quality.

Connection

HDMI connector

A/V device

Computer

HDMI cable

LAN connector

RJ45 cable

Internet

Mini USB socket

USB cable

Computer

RS232

RS232 cable

Computer

3D VESA

3D emitter cable

3D glasses

Computer In

VGA cable

Computer

Component Video to VGA (D-Sub) adapter cable

A/V device

When connecting a signal source to the projector, be sure to:

1. Turn all equipment off before making any connections.

2. Use the correct signal cables for each source.

3. Ensure the cables are firmly inserted.

In the connections shown below, some cables may not be included with the projector (see

"Shipping contents" on page 4). They are commercially available from electronics stores.

The connection illustrations below are for reference only. The connecting jacks available on the projector vary with each projector model.

For detailed connection methods, see pages 19-21.

Below is the connection method for each connector that you may find on your projector.

(for Component signal)

Audio in

Audio cable

Computer

Audio cable

A/V device

Computer Out

VGA cable

Monitor

VGA to DVI-A cable

S-Video connector

S-Video cable

A/V device

Video connector

Video cable

A/V device

Audio in L/R

Audio cable

A/V device

USB 5V/ 2A Out

USB Power Charger

HDMI/MHL connector

HDMI dongle

MHL dongle

MicroUSB cable

IR Out

Remote control wire

(for S-Video/Video signal)

(This connector may be

inside the projector. Open

the cover before using.)

(shared with top IR remote

sensor and a carrier

frequency of 38KHz is

supported)

(Trigger only)

12V Out

Powered screen

MIC

Microphone

Audio Out

Speakers

Connecting a computer or monitor

Connecting a computer

1. Take the supplied VGA cable and connect one end to the D-Sub output socket of the computer.

2. Connect the other end of the VGA cable to the COMPUTER IN 1 or COMPUTER IN 2 signal input socket on the projector.

3. If you wish to use the remote mouse control function, take a USB cable and connect the larger end to the USB port of the computer, and smaller end to the MINI USB socket on the projector. See "Using the remote mouse control" on page 8 for details.

Many notebooks do not turn on their external video ports when connected to a projector. Usually a key combo like FN + F3 or CRT/LCD key turns the external display on/off. Locate a function key labeled CRT/LCD or a function key with a monitor symbol on the notebook. Press FN and the labeled function key simultaneously. Refer to your notebook's documentation to find your notebook's key combination.

Connecting a monitor

If you want to view your presentation close-up on a monitor as well as on the screen, you can connect the COMPUTER OUT signal output socket on the projector to an external monitor with a VGA cable following the instructions below:

1. Connect the projector to a computer as described in "Connecting a computer" on page

19.

2. Take a suitable VGA cable (only one supplied) and connect one end of the cable to the D-Sub input socket of the video monitor. Or if your monitor is equipped with a DVI input socket, take a VGA to DVI-A cable and connect the DVI end of the cable to the DVI input socket of the video monitor.

3. Connect the other end of the cable to the COMPUTER OUT socket on the projector.

The COMPUTER OUT output only works when COMPUTER IN 1 connection is made to the projector in the standby mode. To use this connection method, turn on the Active VGA Out function under the SOURCE > Standby Settings menu.

Connecting Video source devices

You can connect your projector to various Video source devices that provide any one of the following output sockets:

• HDMI

• Component Video

•S-Video

• Video (composite)

You need only connect the projector to a Video source device using just one of the above connecting methods, however each provides a different level of video quality. The method you choose will most likely depend upon the availability of matching terminals on both the projector and the Video source device as described below:

Best video quality

The best available video connection method is HDMI. If your source device is equipped with an HDMI socket, you can enjoy uncompressed digital video quality.

See "Connecting an HDMI device" on page 21 for how to connect the projector to an HDMI source device and other details.

If no HDMI source is available, the next best video signal is Component video (not to be confused with composite video). Digital TV tuner and DVD players output Component video natively, so if available on your devices, this should be your connection method of choice in preference to (composite) video.

See "Connecting a Component Video source device" on page 21 for how to connect the projector to a component video device.

Better video quality

The S-Video method provides a better quality analog video than standard composite Video. If you have both composite Video and S-Video output terminals on your Video source device, you should elect to use the S-Video option.

See "Connecting an S-Video source device" on page 21 for how to connect the projector to an S-Video device.

Least video quality

Composite Video is an analog video and will result in a perfectly acceptable, but less than optimal result from your projector, being the least video quality of the available methods described here.

See "Connecting a composite Video source device" on page 22 for how to connect the projector to a composite Video device.

Connecting audio

You can make use of the projector speaker in your presentations, and also connect separate amplified speakers to the Audio Out socket of the projector. The audio output is controlled by the projector Volume and Mute settings.

Connecting an HDMI device

VGA-Component adapter (ViewSonic P/N: CB-00008906)

You should use an HDMI cable when making connection between the projector and HDMI devices.

1. Take an HDMI cable and connect one end to the HDMI output port of the video device.

2. Connect the other end of the cable to the HDMI input port on the projector.

In the unlikely event that you connect the projector to a DVD player via the projector’s HDMI input and the projected picture displays wrong colors, please change the color space to YUV. See "Changing HDMI input settings" on page 28 for details.

Connecting a Component Video source device

Examine your Video source device to determine if it has a set of unused Component Video output sockets available:

• If so, you can continue with this procedure.

• If not, you will need to reassess which method you can use to connect to the device.

1. Take a VGA (D-Sub)-Component adaptor cable and connect the end with 3 RCA type connectors to the Component Video output sockets of the Video source device. Match the color of the plugs to the color of the sockets; green to green, blue to blue, and red to red.

2. Connect the other end of the VGA (D-Sub)-Component adaptor cable (with a D-Sub type connector) to the COMPUTER IN 1 or COMPUTER IN 2 socket on the projector.

If the selected video image is not displayed after the projector is turned on and the correct video source has been selected, check that the Video source device is turned on and operating correctly. Also check that the signal cables have been connected correctly.

Connecting an S-Video source device

Examine your Video source device to determine if it has an unused S-Video output socket available:

• If so, you can continue with this procedure.

• If not, you will need to reassess which method you can use to connect to the device.

1. Take an S-Video cable and connect one end to the S-Video output socket of the Video source device.

2. Connect the other end of the S-Video cable to the S-VIDEO socket on the projector.

If you have already made a Component Video connection between the projector and this SVideo source device using Component Video connections, you need not connect to this device using an S-Video connection as this makes an unnecessary second connection of poorer picture quality. See "Connecting Video source devices" on page 20 for details.

Connecting a composite Video source device

Examine your Video source device to determine if it has a set of unused composite Video output sockets available:

• If so, you can continue with this procedure.

• If not, you will need to reassess which method you can use to connect to the device.

1. Take a Video cable and connect one end to the composite Video output socket of the Video source device.

2. Connect the other end of the Video cable to the VIDEO socket on the projector.

You need only connect to this device using a composite Video connection if Component Video and S-Video inputs are unavailable for use. See "Connecting Video source devices" on page

20 for details.

Playing sound through the projector

You can make use of the projector speaker in your presentations, and also connect separate amplified speakers to the AUDIO OUT socket of the projector.

You can also use a microphone to output the sound through the projector speaker when the BASIC > Audio Settings > Audio In 2 menu is set to Microphone. See "Adjusting the

Audio In 2 setting" on page 48 for details.

Once connected, the audio can be controlled by the projector On-Screen Display (OSD) menus. See "Adjusting the sound" on page 47 for details.

About the microphone input

• If you wish to use a microphone, connect a 3.5 mini jack cable microphone to the

projector.

• You can use a wireless microphone as long as a wireless module is attached to the

projector’s microphone input jack and it works well with the associated devices. To ensure a quality use of the wireless microphone, it is recommended that your microphone conforms to the specifications listed in the table below.

Signal Parameter Min Ty pe Max

Transducer Principle Dynamic

Microphone

Impedance 300 1K ohm

Frequency response 600 16k Hz

• There are two ways to adjust microphone volumes.

• Directly set microphone volume levels in the BASIC > Audio Settings >

Microphone Volume menu.

• Set projector volume levels in the BASIC > Audio Settings > Audio Settings >

Audio Volume menu, or press (Volume Up)/ (Volume Down) on the remote control. (The projector volume setting will affect the microphone volume.)

• If the microphone is not working, check the volume setting and cable connection.

• You might get feedback noise from the microphone when you are too close to the

speaker of the projector. Move the microphone away from the speaker of the projector.

The greater volume you require, the greater distance you need to be away from the speaker to prevent the noise.

Using the cable management cover

This cable management cover helps you to conceal and organize the cables connected to the back of the projector. It is especially useful when the projector is ceiling-mounted or wallmounted.

1. Make sure that all the cables are properly connected to the projector.

2. Attach the cable management cover to the back of the projector.

3. Tighten the screws that secure the cable management cover.

Operation

Starting up the projector

1. Plug the power cord into the projector and into a wall socket. Turn on the wall socket switch (where fitted).

2. (If available) Remove the lens cap.

3. Press Power to start the projector. As soon as the lamp lights up, a "Power On Ring Tone" will be heard. The Power indicator light stays blue when the projector is on.

(If necessary) Rotate the focus ring to adjust the image clearness.

If the projector is still hot from previous activity, it will run the cooling fan for approximately 90 seconds before energizing the lamp.

To maintain the lamp life, once you turn the projector on, wait at least 5 minutes before turning it off.

To turn off the ring tone, see "Turning off the Power On/Off Ring Tone" on page 48 for details.

4. If the projector is activated for the first time, select your OSD language following the on-screen instructions.

5. Switch all of the connected equipment on.

6. The projector will start to search for input signals. The current input signal being scanned appears in the upper left corner of the screen. If the projector doesn't detect a valid signal, the message 'No Signal' will continue to be displayed until an input signal is found. You can also press Source to select your desired input signal. See "Switching input

signal" on page 28 for details.

If the frequency/resolution of the input signal exceeds the projector's operating range, you will see the message 'Out of Range' displayed on a blank screen. Please change to an input signal which is compatible with the projector's resolution or set the input signal to a lower setting. See "Timing chart" on page 77 for details.

Using the menus

Current input signal

Main menu icon

Sub-menu

Highlight

Go to the previous page or to exit.

Status

The projector is equipped with On-Screen Display (OSD) menus for making various adjustments and settings.

The OSD screenshots below are for reference only, and may differ from the actual design.

Below is the overview of the OSD menu.

To use the OSD menus, please select your language first.

1. Press Menu to turn the OSD menu on.

2. Use / to highlight the SYSTEM menu.

3. Press to highlight Language and press Enter.

4. Use / / / to select a preferred language.

5. Press Menu twice* to leave and save the settings.

*The first press leads you back to the main menu and the second press closes the OSD menu.

Utilizing the password function

For security purposes and to help prevent unauthorized use, the projector includes an option for setting up password security. The password can be set through the On-Screen Display (OSD) menu. For details of the OSD menu operation, please refer to "Using the menus" on

page 25.

You will be inconvenienced if you enable the password function yet forget the password somehow. Do make a note of your password, and keep the note in a safe place for later recall.

Setting a password

Once a password has been set and the power on lock is enabled, the projector cannot be used unless the correct password is entered every time the projector is started.

1. Open the OSD menu and go to the SYSTEM > Security Settings menu.

2. Press Enter and the Security Settings page is displayed.

3. Highlight Power On Lock and select On by pressing / .

4. As pictured to the right, the four arrow keys ( , , , ) respectively represent 4 digits (1, 2, 3, 4). According to the password you desire to set, press the arrow keys to enter six digits for the password.

5. Confirm the new password by re-entering the new password.

Once the password is set, the OSD menu returns to the Security Settings page.

6. To leave the OSD menu, press Exit.

If you forget the password

If the password function is activated, you will be asked to enter the six-digit password every time you turn on the projector. If you enter the wrong password, the password error message as pictured to the right is displayed lasting for 5 seconds, and the message 'INPUT PASSWORD' follows. You can retry by entering another six-digit password, or if you did not record the password in this user manual, and you absolutely do not remember it, you can use the password recall procedure. See "Entering the password recall procedure" on page 27 for details.

If you enter an incorrect password 5 times in succession, the projector will automatically shut down in a short time.

Entering the password recall procedure

1. Press and hold Auto Sync on the remote control for 3 seconds. The projector will display a coded number on the screen.

2. Write down the number and turn off your projector.

3. Seek help from the local service center to decode the number. You may be required to provide proof of purchase documentation to verify that you are an authorized user of the projector.

The "XXX" shown in the above screenshot are numbers that vary depending on different projector models.

Changing the password

1. Open the OSD menu and go to the SYSTEM > Security Settings > Change Password menu.

2. Press Enter. The message 'INPUT CURRENT PASSWORD' is displayed.

3. Enter the old password.

• If the password is correct, another message 'INPUT NEW PASSWORD' is

displayed.

• If the password is incorrect, the password error message is displayed lasting for

5 seconds, and the message 'INPUT CURRENT PASSWORD' is displayed for your retry. You can press Exit to cancel or try another password.

4. Enter a new password.

5. Confirm the new password by re-entering the new password.

6. You have successfully assigned a new password to the projector. Remember to enter the new password next time the projector is started.

7. To leave the OSD menu, press Exit.

The digits being input will be displayed as asterisks on-screen. Do make a note of your password, and then keep the note in a safe place for later recall.

Disabling the password function

1. Open the OSD menu and go to the SYSTEM > Security Settings > Power On Lock menu.

2. Press / to select Off.

3. The message 'INPUT PASSWORD' is displayed. Enter the current password.

• If the password is correct, the OSD menu returns to the Security Settings page

with 'Off' shown in the row of Power On Lock. You will not have to enter the password next time you turn on the projector.

• If the password is incorrect, the password error message is displayed lasting for

5 seconds, and the message 'INPUT PASSWORD' is displayed for your retry. You can press Exit to cancel or try another password.

Though the password function is disabled, you need to keep the old password in hand should you ever need to re-activate the password function by entering the old password.

Switching input signal

The projector can be connected to multiple devices at the same time. However, it can only display one full screen at a time.

Be sure the Quick Auto Search function in the SYSTEM menu is On if you want the projector to automatically search for the signals.

You can also manually select the desired signal by pressing one of the source selection keys on the remote control, or cycle through the available input signals.

1. Press Source. A source selection bar is displayed.

2. Press / until your desired signal is selected and press Enter. Once detected, the selected source information will be displayed on the screen for seconds. If there are multiple devices connected to the projector, repeat steps 1-2 to search for another signal.

Please see "Projector specifications" on page 81 for the native display resolution of this projector. For best display picture results, you should select and use an input signal which outputs at this resolution. Any other resolutions will be scaled by the projector depending upon the 'aspect ratio' setting, which may cause some image distortion or loss of picture clarity. See "Selecting the aspect ratio" on page 32 for details.

Changing HDMI input settings

In the unlikely event that you connect the projector to a device (like a DVD or Blu-ray player) via the projector’s HDMI input and the projected picture displays wrong colors, please change the color space to an appropriate one that fits the color space setting of the output device.

To do this:

1. Open the OSD menu and go to the ADVANCED > HDMI Settings menu.

2. Press Enter.

3. Highlight HDMI Format and press / to select a suitable color space according to the color space setting of the output device connected.

• RGB: Sets the color space as RGB.

• YUV: Sets the color space as YUV.

• Auto: Sets the projector to detect the color space setting of the input signal

automatically.

4. Highlight HDMI Range and press / to select a suitable HDMI color range according to the color range setting of the output device connected.

• Enhanced: Sets the HDMI color range as 0 - 255.

• Normal: Sets the HDMI color range as 15 - 235.

• Auto: Sets the projector to detect the HDMI range of the input signal

automatically.

This function is only available when the HDMI input port is in use.

Refer to the documentation of the device for information on the color space and HDMI range settings.

Adjusting the projected image

Adjusting the projection angle

The projector is equipped with 2 adjuster foot. It changes the image height and vertical projection angle. Press the quick-release buttons and lift the front of the projector. Once the image is positioned where you want it, release the quickrelease buttons to lock the foot in position.

If the projector is not placed on a flat surface or the screen and the projector are not perpendicular to each other, the projected image becomes trapezoidal. To correct this situation, see "Correcting keystone" on page 30 for details.

Do not look into the lens while the lamp is on. The strong light from the lamp may cause damage to your eyes.

Auto-adjusting the image

In some cases, you may need to optimize the picture quality. To do this, press Auto Sync on the remote control. Within 5 seconds, the built-in Intelligent Auto Adjustment function will re-adjust the values of Frequency and Clock to provide the best picture quality.

The current source information will be displayed in the upper left corner of the screen for 3 seconds.

The screen will display ViewSonic logo while auto adjustment is functioning.

This function is only available when PC D-Sub input signal (analog RGB) is selected.

Fine-tuning the image clarity

1. Adjust the projected image to the size that you need using the zoom ring.

2. If necessary, sharpen the image by rotating

the focus ring.

Correcting keystone

Press /

Press / Press /

A long press for 2 seconds on Enter when this page displays will reset the settings on all 4 corners.

Keystoning refers to the situation where the projected image becomes a trapezoid due to angled projection.

To correct this, besides adjusting the height of the projector, you will need to manually correct it following one of these steps.

• Using the remote control

1. Press /// to display the Keystone correction page.

2. Press to correct keystoning at the top of the image. Press to correct keystoning at the bottom of the image. Press to correct keystoning at the right side of the image. Press to correct keystoning at the left side of the image.

• Using the OSD menu

1. Open the OSD menu and go to the

DISPLAY > Keystone > Manual menu.

2. Press Enter.

3. Press to correct keystoning at the top of the image or press to correct keystoning at the bottom of the image. Press to correct keystoning at the right side of the image. Press to correct keystoning at the left side of the image.

The projector can automatically correct vertical keystone. To do this, open the OSD menu and go to the

DISPLAY > Keystone > Auto V Keystone and press / to select On.

Adjusting 4 corners

You can manually adjusts the shape and size of an image that is unevenly rectangular on all sides.

1. To display the Corner Adj. page, you can do one of the followings:

i. Press Enter. ii. Open the OSD menu and go to the

DISPLAY > Corner Adj. menu and

press Enter. The Corner Adj. page is displayed.

2. Press / / / to select the corner you wish to adjust and press Enter.

3. Press / to select an adjustment method

Indicates the corner that you selected.

that suits your need and press Enter.

4. As indicated on the screen ( / for a 45degree angle adjustment and / / / for a 90-degree angle adjustment), press / /

/ to adjust its shape and size. You can press Menu or Exit to go back to a previous step. A long press for 2 seconds on Enter will reset the settings on the corner that you chose.

Adjusting keystone will reset the Corner Adj. settings.

After the Corner Adj. settings have been modified, some aspect ratios or timings are not available. When that happens, reset the settings on all 4 corners. The following messages will appear:

Magnifying and searching for details

If you need to find the details on the projected picture, magnify the picture. Use the direction arrow keys for navigating the picture.

• Using the remote control

1. Press on the remote control to display the Zoom bar.

2. Press repeatedly to magnify the picture to a desired size.

3. To navigate the picture, press Enter to switch to the paning mode and press the directional arrows ( , , , ) to navigate the picture.

4. To reduce size of the picture, you can press Auto Sync on the remote control to restore the picture to its original size. Or you can press Enter to switch back to the zoom in/out functionality and press .

• Using the OSD menu

1. Open the OSD menu and go to the

2. Press Enter. The Zoom bar is displayed.

3. Repeat steps 2-4 in the section of Using the remote control above.

This adjustable range may vary depending on different aspect ratios.

The picture can only be navigated after it is magnified. You can further magnify the picture while searching for details.

DISPLAY > Zoom menu.

Selecting the aspect ratio

The 'aspect ratio' is the ratio of the image width to the image height.

With the advent of digital signal processing, digital display devices like this projector can dynamically stretch and scale the image output to a different aspect than that of the image input signal.

To change the projected image ratio (no matter what aspect the source is):

1. Open the OSD menu and go to the

2. Press Enter.

3. Press / to select an aspect ratio to suit the format of the video signal and your display requirements.

About the aspect ratio

1. Auto: Scales an image proportionally to fit the projector's native resolution in its horizontal width. This is suitable for the incoming image which is neither in 4:3 nor 16:9 and you want to make most use of the screen without altering the image's aspect ratio.

2. 4:3: Scales an image so that it is displayed in the center of the screen with a 4:3 aspect ratio. This is most suitable for 4:3 images like computer monitors, standard definition TV and 4:3 aspect DVD movies, as it displays them without aspect alteration.

3. 16:9: Scales an image so that it is displayed in the center of the screen with a 16:9 aspect ratio. This is most suitable for images which are already in a 16:9 aspect, like high definition TV, as it displays them without aspect alteration.

4. 16:10: Scales an image so that it is displayed in the center of the screen with a 16:10 aspect ratio. This is most suitable for images which are already in a 16:10 aspect, as it displays them without aspect alteration.

5. Panorama: Scales a 4:3 image vertically and horizontally in a non-linear manner so that it fills the screen.

6. 2.35:1: Scales an image so that it is displayed in the center of the screen with a 2.35:1 aspect ratio without aspect alteration.

7. Anamorphic: Scales a 2.35:1 aspect image so that it fills the screen.

The table below demonstrates the effects of the aspect ratio settings on projectors with different native resolutions. Please see "Projector specifications" on page 81 for the native display resolution of your projector.

In the pictures below, the black portions are inactive areas and the white portions are active areas. OSD menus can be displayed on those unused black areas.

Aspect ratio setting

When the native aspect ratio of your projector is...

4:3 16:9 16:10

DISPLAY > Aspect Ratio menu.

Auto

4:3

16:9 Not available

16:10

Panorama

2.35:1

Anamorphic

Not

available

Not

available

Not

available

Not available

Optimizing the image

Selecting a picture mode

The projector is preset with several predefined picture modes so that you can choose one to suit your operating environment and input signal picture type.

To select an operation mode that suits your need, you can follow one of the following steps.

• Press Color Mode to display the selection bar and press / to select a desired mode

or press Color Mode repeatedly.

•Go to the IMAGE > Color Mode menu and press Enter. Press / to select a

desired mode.

Picture modes for different types of signals

The picture modes available for different types of signals are listed below.

1. Brightest mode: Maximizes the brightness of the projected image. This mode is suitable for environments where extra-high brightness is required, such as using the projector in well lit rooms.

2. Dynamic mode: Is designed for presentations under daylight environment to match PC and notebook coloring. In addition, the projector will optimize the image quality using the dynamic PC function in accordance with the projected contents.

3. Standard mode: Is designed for presentations under daylight environment to match PC and notebook coloring.

4. ViewMatch sRGB mode: Switches between high brightness performance and accurate color performance.

5. Movie mode: Is appropriate for playing colorful movies, video clips from digital cameras or DVs through the PC input for best viewing in a blackened (little light) environment.

6. DICOM SIM mode: Recommended for DICOM format files in simulation mode.

DICOM SIM mode is only for training or reference. It not used for actual diagnosis.

-30

+80

DICOM represents for the Digital Imaging and Communications in Medicine. This is a standard created by the American College of Radiology and the National Electrical Manufacturers Association. This standard specifies the method of digital image data to be transferred from one system to another.

Using Screen Color

In the situation where you are projecting onto a colored surface such as a painted wall which may not be white, the Screen Color feature can help correct the projected picture’s colors to prevent possible color difference between the source and projected pictures.

To use this function, go to the DISPLAY > Screen Color menu and press Enter. Press /

to select a color which is closest to the color of the projection surface. There are several precalibrated colors to choose from: Whiteboard, Greenboard, and Blackboard. The effects of these settings may vary depending on different models.

This function is only available when a computer input signal is selected.

Fine-tuning the image quality in user modes

According to the detected signal type, there are some user-definable functions available. You can make adjustments to these functions based on your needs.

Adjusting Brightness

Go to the IMAGE > Brightness menu and press Enter.

The higher the value, the brighter the image. And the lower the setting, the darker the image. Adjust this control so the black areas of the image appear just as black and that detail in the dark areas is visible.

Adjusting Contrast

Go to the IMAGE > Contrast menu and press Enter.

The higher the value, the greater the contrast. Use this to set the peak white level after you have previously adjusted the Brightness setting to suit your selected input and viewing environment.

Adjusting Color

Go to the IMAGE > Advanced > Color menu and press / .

Lower setting produces less saturated colors. If the setting is too high, colors on the image will be overpowering, which makes the image unrealistic.

This function is only available when the input signal is S-Video, Video, YPbPr (digital) or YCbCr (digital).

-30

+40

Adjusting Tint

Go to the IMAGE > Advanced > Tint menu and press / .

The higher the value, the more reddish the picture becomes. The lower the value, the more greenish the picture becomes.

This function is only available when the input signal is S-Video, Video, YPbPr (digital) or YCbCr (digital).

Adjusting Sharpness

Go to the IMAGE > Advanced > Sharpness menu and press / .

The higher the value, the sharper the picture becomes. The lower the value, the softer the picture becomes.

This function is only available when the input signal is S-Video, Video, YPbPr (digital) or YCbCr (digital).

Adjusting Brilliant Color

Go to the IMAGE > Advanced > Brilliant Color menu and press / .

This feature utilizes a new color-processing algorithm and system level enhancements to enable higher brightness while providing truer, more vibrant colors in the projected picture. It enables a greater than 50% brightness increase in mid-tone images, which are common in video and natural scenes, so the projector reproduces images in realistic and true colors. If you prefer images with that quality, select a level that suits your need. If you don’t need it, select Off.

Reducing image noise

Go to the IMAGE > Advanced > Noise Reduction menu and press / .

This function reduces electrical image noise caused by different media players. The higher the setting, the less the noise.

This function is only available when a PC, Video or S-Video input signal is selected.

Selecting a gamma setting

Go to the IMAGE > Advanced > Gamma menu and select a preferred setting by pressing

/ .

Gamma refers to the relationship between input source and picture brightness.

Selecting a Color Temperature

Go to the IMAGE > Color Temp. menu and press Enter.

The options available for color temperature settings vary according to the signal type selected.

1. Cool: With the highest color temperature, Cool makes the image appear the most

bluish white than other settings.

2. Neutral: Makes images appear bluish white.

3. Normal: Maintains normal colorings for white.

4. Warm: Makes images appear reddish white.

Setting a preferred color temperature

1. Go to the IMAGE > Color Temp. menu and press Enter.

2. Press / to select Cool, Neutral, Normal or Warm and press Enter.

3. Press / to highlight the item you want to change and adjust the values by

pressing /

• Red Gain/Green Gain/Blue Gain: Adjusts the contrast levels of Red, Green, and Blue.

• Red Offset/Green Offset/Blue Offset: Adjusts the brightness levels of Red, Green, and Blue.

This function is only available when a computer input signal is selected.

Color Management

RED

BLUE

GREEN

Yellow

Cyan

Magenta

Only in permanent installations with controlled lighting levels such as boardrooms, lecture theaters, or home theaters, should color management be considered. Color management provides fine color control adjustment to allow for more accurate color reproduction, should you require it.

If you have purchased a test disc which contains various color test patterns and can be used to test the color presentation on monitors, TVs, projectors, etc., you can project any image from the disc on the screen and enter the Color Management menu to make adjustments.

To adjust the settings:

1. Open the OSD menu and go to the IMAGE > Advanced > Color Management menu.

2. Press Enter and the Color Management page is displayed.

3. Highlight Primary Color and press / to select a color from among Red, Yellow, Green, Cyan, Blue, or Magenta.

4. Press to highlight Hue and press / to select its range. Increase in the range will include colors consisted of more proportions of its two adjacent colors. Please refer to the illustration to the right for how the colors relate to each other.

For example, if you select Red and set its range at 0, only pure red in the projected picture will be selected. Increasing its range will include red close to yellow and red close to magenta.

5. Press to highlight Saturation and adjust its values to your preference by pressing /

. Every adjustment made will reflect to the

image immediately. For example, if you select Red and set its

value at 0, only the saturation of pure red will be affected.

Saturation is the amount of that color in a video picture. Lower settings produce less saturated colors; a setting of “0” removes that color from the image entirely. If the saturation is too high, that color will be overpowering and unrealistic.

6. Press to highlight Gain and adjust its values to your preference by pressing / . The contrast level of the primary color you select will be affected. Every adjustment made will reflect to the image immediately.

7. Repeat steps 3 to 6 for other color adjustments.

8. Make sure you have made all of the desired adjustments.

Setting the presentation timer

Presentation timer can indicate the presentation time on the screen to help you achieve better time management when giving presentations. Follow these steps to utilize this function:

• Using the remote control

1. Press on the remote control and press repeatedly or / to select a Timer Period.

2. Press Enter or wait for 3 seconds to activate the timer.

3. To display the Presentation Timer page, select Advanced.

• Using the OSD menu

1. Go to the BASIC > Presentation Timer menu.

2. Press Enter to display the Presentation Timer page.

3. Highlight Timer Period and decide the time period by pressing / . The length of time can be set from 1 to 5 minutes in 1-minute increments and 5 to 240 minutes in 5minute increments.

If the timer is already on, the timer will restart whenever the Timer Period is reset.

4. Press to highlight Timer Display and choose if you want the timer to show up on the screen by pressing

Selection Description

Always

1 min/2 min/3 min Displays the timer on screen in the last 1/2/3 minute(s). Never Hides the timer throughout the presentation time.

5. Press to highlight Timer Position and set the timer position by pressing / .

Top-Left Bottom-Left Top-Right Bottom-Right

6. Press to highlight Timer Counting Direction and select your desired counting direction by pressing / .

Selection Description Count Up Increases from 0 to the preset time. Count Down Decreases from the preset time to 0.

/ .

Displays the timer on screen throughout the presentation time.

7. Press to highlight Sound Reminder and decide if you want to activate sound reminder by pressing / . If you select On, a double beep sound will be heard at

the last 30 seconds of counting down/up, and a triple beep sound will be produced when the timer is up.

8. To activate the presentation timer, press and press / to highlight Start Counting and press Enter.

9. A confirmation message displays. Highlight Yes and press Enter to confirm. You will see the message “Timer is On” displaying on the screen. The timer starts counting when the timer is on.

To cancel the timer, perform the following steps:

1. Press on the remote control or go to the BASIC > Presentation Timer menu.

2. Highlight Off. Press Enter. A confirmation message displays.

3. Highlight Yes and press Enter to confirm. You will see the message “Timer is Off” displaying on the screen.

Hiding the image

In order to draw the audience's full attention to the presenter, you can press BLANK to hide the screen image. Press any key on the projector or remote control to restore the image. The word 'BLANK' appears at the lower right corner of the screen while the image is hidden.

You can set the blank time in the BASIC > Blank Timer menu to let the projector return the image automatically after a period of time when there is no action taken on the blank screen.

Once Blank is pressed, the projector enters Eco mode automatically.

CAUTION

Do not block the projection lens from projecting as this could cause the blocking object to become heated and deformed or even cause a fire.

Locking control keys

With the control keys on the projector locked, you can prevent your projector settings from being changed accidentally (by children, for example). When the Panel Key Lock is on, no

control keys on the projector will operate except Power.

1. Press (Panel Key Lock), or go to the

2. Press Enter and press / to select On.

3. A confirmation message is displayed. Select Yes to confirm.

To release panel key lock, press and hold on the projector for 3 seconds.

You can also use the remote control to enter the select Off.

Keys on the remote control are still functional when panel key lock is enabled.

If you press Power to turn off the projector without disabling panel key lock, the projector will still be in locked status the next time it is turned on.

SYSTEM > Panel Key Lock menu

SYSTEM > Panel Key Lock menu and

Creating your own startup screen

In addition to selecting the projector preset startup screen from among Black, Blue, or ViewSonic screen, you can make your own startup screen that is a picture projected from

your computer or video source.

To create your own startup screen:

1. Project the picture you want to use as your startup screen from either a computer or video source.

2. Open the OSD menu and go to the BASIC > Screen Capture menu.

3. Press Enter.

4. A confirmation message displays. Press Enter again.

5. The message 'Screen Capturing...' displays while the projector is processing the picture. Please wait.

6. If the action is successful, you see the message 'Captured Succeeded' on the screen. The captured picture is saved as Screen Capture and have been set as your current startup screen.

In the unlikely event that the capturing action fails, change your target picture. When it happens, please set the resolution of the input signal under native resolution and try again.

Operating in a high altitude environment

We recommend you use the High Altitude Mode when your environment is between 1500 m–3000 m above sea level, and temperature is between 5°C–25°C.

CAUTION

Do not use the High Altitude Mode if your altitude is between 0 m and 1500 m and temperature is between 5°C and 35°C. The projector will be over cooled, if you turn the mode on under such a condition.

To activate the High Altitude Mode:

1. Open the OSD menu and go to the SYSTEM > High Altitude Mode menu.

2. Press Enter and press / to select On. A confirmation message is displayed.

3. Highlight Yes and press Enter.

Operation under "High Altitude Mode" may cause a higher decibel operating noise level because of increased fan speed necessary to improve overall system cooling and performance.

If you use this projector under other extreme conditions excluding the above, it may display auto shut-down symptoms, which is designed to protect your projector from over-heating. In cases like this, you should switch to High Altitude Mode to solve these symptoms. However, this is not to state that this projector can operate under any and all harsh or extreme conditions.

Using the CEC function

This projector supports CEC (Consumer Electronics Control) function for synchronized power on/off operation via HDMI connection. That is, if a device that also supports CEC function is connected to the HDMI input of the projector, when the projector’s power is turned off, the power of the connected device will also be turned off automatically. When the power of the connected device is turned on, the projector’s power will be turned on automatically.

To turn on the CEC function:

1. Open the OSD menu and go to the POWER MANAGEMENT > Auto Power On > CEC menu.

2. Press / to select Enable.

In order for the CEC function to work properly, make sure that the device is correctly connected to the HDMI input of the projector via an HDMI cable, and its CEC function is turned on.

Depending on the connected device, the CEC function may not work.

Using the 3D functions

This projector features 3D function which enables you to enjoy 3D movies, videos, and sporting events in a more realistic way by presenting the depth of the images. You need to wear a pair of 3D glasses to view 3D images.

If the 3D signal is input from an HDMI 1.4a compatible device, the projector detects the signal for 3D Sync information and once detected, it projects images in 3D format automatically. In other cases, you may need to manually select a 3D Sync format for the projector to project 3D images correctly.

1. Go to the ADVANCED > 3D Settings menu.

2. Press Enter. The 3D Settings page is displayed.

3. Highlight 3D Glasses and press / to select DLP or 3D VESA.

4. Highlight 3D Sync and press Enter.

5. Press to select a 3D Sync setting and then press Enter to confirm.

(An example of connection)

When the 3D Sync function is on:

• The brightness level of the projected image will decrease.

• The Color Mode cannot be adjusted.

• The Zoom function can only magnify the pictures to limited sizes.

If you discover the inversion of the 3D image depth, set the 3D Sync Invert function to “Invert” to correct the problem.

Controlling the projector through a LAN environment

The projector supports Crestron® software. With correct settings for the LAN Control Settings menu, you can manage the projector from a computer using a web browser when

the computer and the projector are properly connected to the same local area network.

Configuring the LAN Control Settings

If you are in a DHCP environment:

1. Take a RJ45 cable and connect one end to the RJ45 LAN input jack of the projector and the other end to the RJ45 port.

2. Open the OSD menu and go to the ADVANCED > LAN Control Settings menu.

3. Press Enter. The LAN Control Settings page is displayed.

4. Highlight LAN Control Settings and press / to select DHCP ON.

5. Press to highlight Apply and press Enter.

6. Please wait for around 15 - 20 seconds, and then re-enter the LAN Control Settings page. The Projector IP Address, Subnet Mask, Default Gateway, and DNS Server settings will be displayed. Note down the IP address displayed in the Projector IP Address row.

If the Projector IP Address still does not appear, contact your network administrator.

If the RJ45 cables are not properly connected, the Projector IP Address, Subnet Mask, Default Gateway, and DNS Server settings will display 0.0.0.0. Make sure the cables are properly connected and perform the procedures above again.

If you need to connect to the projector in its standby mode, set Standby LAN Control to On in the ADVANCED > LAN Control Settings menu.

If you are in a non-DHCP environment:

1. Repeat steps 1-3 above.

2. Highlight LAN Control Settings and press / to select Static IP.

3. Contact your ITS administrator for information on the Projector IP Address, Subnet Mask, Default Gateway, and DNS Server settings.

4. Press to select the item you want to modify and press Enter.

5. Press / to move the cursor and the press / to enter the value.

6. To save the settings, press Enter. If you do not want to save the settings, press Exit.

7. Press to highlight Apply and press Enter.

If you wish to connect to the projector in its standby mode, be sure you have selected Static IP and obtained the Projector IP Address, Subnet Mask, Default Gateway, and DNS Server information when the projector is on.

Controlling the projector through a web browser

Once you have the correct IP address for the projector and the projector is on or in standby mode, you can use any computer that is on the same local area network to control the projector.

If you are using Microsoft Internet Explorer, make sure it is version 7.0 or higher.

The screen shots in this manual are for reference only, and may differ from the actual design.

1. Enter the address of the projector in the address bar of your browser and press Enter.

2. The main page of the Network Control appears.

Accessing to Network Settings or Email Alert page requires Administrator password. The default password is "0000".

3. This page allows you to make adjustments to the AMX and SNMP settings. In the AMX device discover row, when ON is selected, the projector can be detected by

controllers of AMX connected to the same network. For the Details of AMX Device Discovery, visit the AMX web site at http://www.amx.com/.

4. If your projector is connected to a network which supports Simple Mail Transfer Protocol (SMTP), you can configure it to alert you via email on significant events.

5. The Crestron (e-Control) page displays the Crestron e-Control user interface. See

"About Crestron e-Control®" on page 44 for details.

Please pay attention to the limitation of input length (including space and other punctuation keys) in the list blow:

Category Item Input Length

DHCP/Manual (N/A)

IP Address XXX.XXX.XXX.XXX

Network

Network Settings

Password

SNMP

Email Setting

SMTP Setting

Email Alert

Alert Condition

Subnet Mask XXX.XXX.XXX.XXX

Gateway XXX.XXX.XXX.XXX

DNS Server XXX.XXX.XXX.XXX

AMX device discovery (N/A)

Administrator (N/A)

New Password 4

Confirm Password 4

SysLocation 22

SysName 22

SysContact 22

To 40

Cc 40

Subject 40

From 40

Server 30

User Name 21

Password 14

Fan Error (N/A)

Lamp Error (N/A)

Over Temperature (N/A)

Lamp Time Alert (N/A)

Submit (N/A)

Issue Test Mail (N/A)

Maximum Number of Characters

/ > < $ % + \ ' " are prohibited.

About Crestron e-Control

You can press

/ to

reveal more buttons.

i iv

iii

1. The Crestron e-Control® page provides a variety of virtual keys to control the projector or adjust the projected pictures.

i. These buttons function the same as the ones on the OSD menus or remote control.

See "2. IMAGE menu" on page 55 and "Projector" on page 7 for details.

ii. To switch between input signals, click on your desired signal.

The Menu button can also be used to go back to previous OSD menus, exit and save menu settings.

The source list varies according to the connectors available on the projector.

When you use the projector control panel or remote control to change the OSD menu settings, it may take a while for the web browser to synchronize these changes with the projector.

2. The tools page allows you to manage the projector, configure the LAN control settings and secure access of remote network operation on this projector.

i. This section is only used with the Crestron Control System. Please contact

Creston or refer to its user manual for setup information.

ii. You can name the projector, keep track of its location and the person in charge of

it.

iii. You can adjust the LAN Control Settings. iv. Once set, access to the remote network operation on this projector has been

password-protected.

v. Once set, access to the tools page has been password-protected.

To prevent errors, only input the English alphabet and digits on the tools page.

After making the adjustments, press the Send button and the data will be saved for the projector.

vi. Press Exit to go back to the remote network operation page.

Please pay attention to the limitation of input length (including space and other punctuation keys) in the list blow:

Category Item Input Length

IP Address 16

Crestron Control

Projector

Network Configuration

User Password

Admin Password

IP ID 4

Port 5

Projector Name 32

Location 32

Assigned To 32

DHCP (Enabled) (N/A)

IP Address 16

Subnet Mask 16

Default Gateway 16

DNS Server 16

Enabled (N/A)

New Password 26

Confirm 26

Enabled (N/A)

New Password 26

Confirm 26

Maximum Number of Characters

3. The info page displays the information and status of this projector.

Press Exit to go back to the remote network operation page.

4. After pressing the button “Contact IT Help”, the HELP DESK window will appear in the upper right corner of the screen. You will be able to deliver messages to RoomView™ software administrators/users who connect to the same local area network.

For more information, visit http://www.crestron.com & www.crestron.com/getroomview.

**Crestron RoomView

On the “Edit Room” page, enter the IP Address (or hostname) as shown on the projector’s on-screen display (OSD) menu, and “02” for IPID, “41794” for the reserved Crestron control port.

About Crestron RoomView™ setting and command method, please access below website to get RoomView™ User Guide and more information:

http://www.crestron.com/products/roomview_connected_embedded_projectors_devices/ resources.asp

PJLink™, SNMP, AMX and Xpanel formats supported

This projector is PJLink™, SNMP V.1, AMX or Xpanel V1.10 compliant. For details, please follow its user guide or website respectively to control and manage projectors.

Using the projector in standby mode

Some of the projector functions are available in standby mode (plugged in but not turned on). To use these functions, be sure the cable connections are correctly made. For the connection methods, see the Connection chapter.

Active VGA Out

Selecting On in the POWER MANAGEMENT > Standby Settings > Active VGA Out outputs a VGA signal when the COMPUTER IN 1 and COMPUTER OUT sockets are correctly connected to devices. The projector outputs the signal received only from

COMPUTER IN 1.

Active Audio Out

Selecting On in the POWER MANAGEMENT > Standby Settings > Active Audio Out outputs an audio signal when the AUDIO IN 1 socket is correctly connected to a proper device.

LAN Control

Selecting On in the ADVANCED > LAN Control Settings > Standby LAN Control allows the projector to provide the network function when it is in standby mode. See

"Controlling the projector through a LAN environment" on page 40 for details.

Adjusting the sound

The sound adjustments made as below will have an effect on the projector speaker. Be sure you have made a correct connection to the projector audio input/output jacks. See

"Connection" on page 15 for more details.

Adjusting the audio mode

1. Open the OSD menu and go to the BASIC > Audio Settings > Audio Mode menu.

2. Press / to select a preferred audio mode.

If available, you can press Audio Mode on the remote control to select a preferred audio mode.

Muting the sound

1. Open the OSD menu and go to the BASIC > Audio Settings > Mute menu.

2. Press / to select On.

If available, you can press on the remote control to toggle the projector audio between on and off.

Adjusting the sound level

1. Open the OSD menu and go to the BASIC > Audio Settings > Audio Volume menu.

2. Press / to select a desired sound level.

If available, you can press / on the remote control to adjust the projector’s sound level.

Adjusting the Audio In 2 setting

1. Open the OSD menu and go to the BASIC > Audio Settings > Audio In 2 menu.

2. Press / to decide the audio input source for the AUDIO IN 2/MIC port. This will affect the connection method for different devices, and where the sound is from.

• When Audio is selected:

Device

Audio input port

The projector can play

the sound from...

Audio output port

The selected input signal determines which sound will be played by the projector speaker, and which sound will be output from the projector when AUDIO OUT is connected. For instance, if you select a D-Sub / Comp. 1 source, the projector can play the sound received from AUDIO IN

COMPUTER IN 1 COMPUTER IN 2 Video/S-Video

AUDIO IN 1 AUDIO IN 2 AUDIO IN 2

AUDIO OUT AUDIO OUT AUDIO OUT

• When Microphone is selected:

Device

Audio input port

The projector can play

the sound from...

Audio output port

COMPUTER IN 1 COMPUTER IN 2 Video/S-Video

AUDIO IN 1 AUDIO IN 1 AUDIO IN 1

• AUDIO IN 1

•MIC

AUDIO OUT AUDIO OUT AUDIO OUT

• AUDIO IN 1

•MIC

• AUDIO IN 1

•MIC

Adjusting the microphone sound level

1. Open the OSD menu and go to the BASIC > Audio Settings > Microphone Volume menu.

2. Press / to select a desired sound level.

This function is only available when the BASIC > Audio Settings > Audio In 2 menu is set to Microphone. The microphone volume will be changed to 1 after each setting adjustment.

Turning off the Power On/Off Ring Tone

1. Open the OSD menu and go to the BASIC > Audio Settings > Power On/Off Ring Tone menu.

2. Press / to select Off.

The only way to change Power On/Off Ring Tone is setting On or Off here. Setting the sound mute or changing the sound level will not affect the Power On/Off Ring Tone.

Shutting down the projector

1. Press Power and a confirmation message is displayed prompting you.

If you don't respond in a few seconds, the message will disappear.

2. Press Power a second time.

3. Once the cooling process finishes, a "Power Off Ring Tone" will be heard. Disconnect the power cord from the wall socket if the projector will not be used in an extended period of time.

To turn off the ring tone, see "Turning off the Power On/Off Ring Tone" on page 48 for details.

CAUTION

• To protect the lamp, the projector will not respond to any commands during the cooling

process.

• Do not unplug the power cord before the projector shutdown sequence is complete.

Menu operation

Menu system

Please note that the on-screen display (OSD) menus vary according to the signal type selected.

The menu items are available when the projector detects at least one valid signal. If there is no equipment connected to the projector or no signal detected, limited menu items are accessible.

Main menu Sub-menu Options

Screen Color Off/Blackboard/Greenboard/Whiteboard

Auto/4:3/16:9/16:10/Panorama/2.35:1/ Anamorphic

Off/On

Red Gain/Green Gain/ Blue Gain/Red Offset/ Green Offset/Blue Offset

Primary Color Hue Saturation Gain

DISPLAY

IMAGE

Aspect Ratio

Auto V

Keystone

Corner Adj. Position Phase H. Size Zoom OverScan Off/1/2/3/4/5

Color Mode

Brightness Contrast

Color Temp.

Advanced

Reset Color Settings Reset/Cancel

Keystone Manual Vertical/Horizontal

Brightest/Dynamic/Standard/ViewMatch sRGB/Movie/ DICOM SIM

Warm Normal Neutral Cool Color Tint Sharpness Gamma 1/2/3/4/5/6/7/8 Brilliant Color Off/1/2/3/4/5/6/7/8/9/10 Noise Reduction

Color Management

Main menu Sub-menu Options

Computer Disable/Enable

POWER

MANAGEMENT

4. BASIC

Auto Power On

Smart Energy

MHL Settings

Standby Settings

Audio Settings

Presentation Timer

Pattern

Blank Timer

Message On/Off

Splash Screen

Screen Capture

CEC Disable/Enable Direct Power On Off/On Auto Power Off Disable/10 min/20 min/30 min

Sleep Timer

Power Saving Enable/Disable Power Out HDMI/MHL 4/USB 1/USB 2 MHL Reset Reset/Cancel Active VGA Out Off/On Active Audio Out Off/On

Audio Mode

Mute On/Off Audio Volume Audio In 2 Audio/Microphone Microphone Volume Power On/Off Ring

Tone Timer Period 1~240 m Timer Display Always/1 min/2 min/3 min

Timer Position

Timer Counting Direction

Sound Reminder On/Off Start Counting/Off

Disable/30 min/1 hr /2 hr/3 hr/ 4 hr/8 hr/12 hr

Standard/Speech/ Entertainment

On/Off

Top-Left/Bottom-Left/TopRight//Bottom-Right

Count Down/Count Up

Off/Test Card/Note Pad / World Map/Stave/Trellis Chart

Disable/5 min/10 min/15 min/ 20 min/25 min/30 min

Black/Blue/ViewSonic/ Screen Capture/Off

Main menu Sub-menu Options

Auto/Projection (Projector Position)/Menu

BASIC

ADVANCED

My Button

3D Settings

HDMI Settings

LAN Control Settings

Lamp Settings

Filter Settings

DCR On/Off Closed Caption Caption Version CC1/CC2/CC3/CC4 Reset Settings Reset/Cancel

Position/Color Temp./Brightness/Contrast/3D Settings/Screen Color/Splash Screen/ Message/Quick Auto Search/CEC/DCR/Closed Caption/Power Saving/Freeze/INFORMATION/ Aspect Ratio/Power Out

3D Glasses DLP/3D VESA

Auto/Off/Frame

3D Sync

3D Sync Invert Disable/Invert HDMI Format Auto/RGB/YUV HDMI Range Auto/Enhanced/Normal LAN Control Settings DHCP ON/Static IP Projector IP Address Subnet Mask Default Gateway DNS Server Standby LAN Control Off/On Apply Lamp Mode Normal/Eco Reset Lamp Hours Lamp Hours Filter Mode On/Off Reset Filter Hours Filter Hours

Sequential/Frame Packing/Top-Bottom/ Side-by-Side

Main menu Sub-menu Options

Multi-language OSD selection

Front Table/Rear Table/ Rear Ceiling/Front Ceiling

5 sec/10 sec/15 sec/20 sec/25 sec/30 sec

Center/Top-Left/TopRight/Bottom-Left/ Bottom-Right

6. SYSTEM

INFORMATION

Language

Projector Position

Menu Display Time

Menu Settings

Menu Position

High Altitude Mode On/Off Quick Auto Search Off/On

Security Settings

Panel Key Lock Off/On Remote Control Code 1/2/3/4/5/6/7/8

• Source

• Color Mode

• Resolution

• Color System

• IP Address

• MAC Address

• Firmware Version

Change Password Power On Lock Off/On

Description of each menu

1. DISPLAY menu

Function Description

Screen Color See "Using Screen Color" on page 34 for details.

Aspect Ratio See "Selecting the aspect ratio" on page 32 for details.

Keystone See "Correcting keystone" on page 30 for details.

Corner Adj. See "Adjusting 4 corners" on page 30 for details.

Displays the position adjustment page. To move the projected image, use the directional arrow keys. The values shown on the lower position of the page change with every key press you made

Position

Phase

H. Size

Zoom

OverScan

until they reach their maximum or minimum.

This function is only available when a PC input signal is selected.

The adjustment range may vary under different timings.

Adjusts the clock phase to reduce image distortion.

This function is only available when a PC input signal is selected.

Adjusts the horizontal width of the image.

This function is only available when a PC input signal is selected.

See "Magnifying and searching for details" on page 31 for details.

Adjusts the overscan rate from 0% to 5%.

This function is only available when a Composite Video, S-Video or HDMI input signal is selected.

Function Description

2. IMAGE menu

Color Mode See "Selecting a picture mode" on page 33 for details.

Brightness See "Adjusting Brightness" on page 34 for details.

Contrast See "Adjusting Contrast" on page 34 for details.

Color Temp.

Advanced

Reset Color Settings

See "Selecting a Color Temperature" on page 35 and "Setting a

preferred color temperature" on page 35 for details.

Color

See "Adjusting Color" on page 34 for details.

Tint

See "Adjusting Tint" on page 34 for details.

Sharpness

See "Adjusting Sharpness" on page 35 for details.

Gamma

See "Selecting a gamma setting" on page 35 for details.

Brilliant Color

See "Adjusting Brilliant Color" on page 35 for details.

Noise Reduction

See "Reducing image noise" on page 35 for details.

Color Management

See "Color Management" on page 36 for details.

Returns all color settings to the factory preset values.

Function Description

3. POWER MANAGEMENT menu

4. BASIC menu

Computer

Selecting Enable allows the projector to turn on automatically once the VGA signal is fed through the VGA cable.

Auto Power On

Smart Energy

MHL Settings

Audio Settings See "Adjusting the sound" on page 47 for details.

Presentation Timer

Pattern

Blank Timer See "Hiding the image" on page 37 for details.

Message

Splash Screen

Screen Capture See "Creating your own startup screen" on page 38 for details.

My Button Sets a hotkey on remote control.

CEC

See "Using the CEC function" on page 39 for details.

Direct Power On

Selecting On allows the projector to turn on automatically once the power is fed through the power cord.

Auto Power Off

See "Setting Auto Power Off" on page 61 for details.

Sleep Timer

See "Setting Sleep Timer" on page 61 for details.

Power Saving

See "Setting Power Saving" on page 61 for details.

Power Out

Sets the MHL power output port. If the MHL/HDMI input can't be detected, reset Power Out.

MHL Reset

Selecting Reset to reapply power after a power outage.

See "Setting the presentation timer" on page 36 for details.

The projector can display several test patterns. It helps you adjust the image size and focus and check that the projected image is free from distortion.

Selecting On displays the current information on the screen when the projector is detecting or searching for a signal.

Allows you to select which logo screen will be displayed during projector start-up.

5. ADVANCED menu

Function Description

3D Settings See "Using the 3D functions" on page 39 for details.

HDMI Settings See "Changing HDMI input settings" on page 28 for details.

LAN Control Settings

See "Controlling the projector through a LAN environment"

on page 40 for details.

Lamp Mode

See "Setting Lamp Mode" on page 61 for details.

Reset Lamp Hours

Lamp Settings

Resets the lamp timer after new lamp is installed. For changing the lamp, please contact qualified service personnel.

Lamp Hours

See "Getting to know the lamp hour" on page 61 for details on how the total lamp hour is calculated.

Filter Settings

See "Using the dust filter (optional accessory)" on page 59 for details.

Enables or disables the DCR (Dynamic Contrast Ratio) function. Selecting On enables the function and the projector will automatically switch the lamp mode between normal and economic modes according to the input image detected.

DCR

This function is only available when a PC input signal is selected.

After enabling DCR, frequent lamp mode switching may shorten lamp life and noise level will vary during operation.

Selects a preferred closed captioning mode when the selected input signal carries closed captions.

• Captions: An on-screen display of the dialogue, narration, and sound effects of TV programs and videos that are closed captioned (usually marked as "CC" in TV listings).

Closed Caption

This function is only available when a Composite video or S-Video input signal is selected and its system format is NTSC.

Caption Version

To view captions, select CC1, CC2, CC3, or CC4 (CC1 displays captions in the primary language in your area).

Returns all settings to the factory preset values.

The following settings will still remain: Keystone, Corner

Reset Settings

Adj., Phase, H. Size, OverScan, Language, Projector Position, High Altitude Mode, Security Settings, Remote Control Code, 3D Sync, Filter Mode, LAN Control Settings, HDMI Settings.

Function Description

6. SYSTEM menu

7. INFORMATION menu

Language

Projector Position

Sets the language for the On-Screen Display (OSD) menus. See "Using the menus" on page 25 for details.

See "Choosing a location" on page 10 for details.

Menu Display Time

Sets the length of time the OSD will remain active after your

Menu Settings

last key press. The range is from 5 to 30 seconds in 5-second increments.

Menu Position

Sets the On-Screen Display (OSD) menu position.

High Altitude Mode

Quick Auto Search

Security Settings

A mode for operation in high altitude areas. See "Operating

in a high altitude environment" on page 38 for details.

See "Switching input signal" on page 28 for details.

See "Utilizing the password function" on page 26 for details.

Panel Key Lock See "Locking control keys" on page 38 for details.

Remote Control Code

See "Remote control code" on page 8 for details.

Source

Shows the current signal source.

Color Mode Shows the selected mode in the IMAGE menu.

Resolution

Shows the native resolution of the input signal.

Color System

Current System Status

Shows input system format.

IP Address

Shows the IP address of your projector.

MAC Address

Shows the MAC Address of your projector.

MAC Address stands for Media Access Control Address, which is a physical layer address used to uniquely identify a network node.

Firmware Version

Shows the current firmware version.

Maintenance

Care of the projector

You need to keep the lens and/or filter (optional accessory) clean on a regular basis.

Never remove any parts of the projector. Contact your dealer when any part of the projector needs replacing.

Cleaning the lens

Clean the lens whenever you notice dirt or dust on the surface.

• Use a canister of compressed air to remove dust.

• If there is dirt or smears, use lens-cleaning paper or moisten a soft cloth with lens cleaner and gently wipe the lens surface.

CAUTION

Never rub the lens with abrasive materials.

Cleaning the projector case

Before you clean the case, turn the projector off using the proper shutdown procedure as described in "Shutting down the projector" on page 49 and unplug the power cord.

• To remove dirt or dust, wipe the case with a soft, lint-free cloth.

• To remove stubborn dirt or stains, moisten a soft cloth with water and a neutral pH detergent. Then wipe the case.

CAUTION

Never use wax, alcohol, benzene, thinner or other chemical detergents. These can damage the case.

Storing the projector

If you need to store the projector for an extended time, please follow the instructions below:

• Make sure the temperature and humidity of the storage area are within the recommended range for the projector. Please refer to "Specifications" on page 65 or consult your dealer about the range.

• Retract the adjuster foot.

• Remove the battery from the remote control.

• Pack the projector in its original packing or equivalent.

Transporting the projector

It is recommended that you ship the projector with its original packing or equivalent.

Using the dust filter (optional accessory)

CAUTION

• It is recommended to clean the dust filter every 100 hours after the dust filter is installed.

• Be sure to turn off the projector and unplug it from power source before installing or detaching the filter.

• If your projector is ceiling-mounted or is not easily accessible, pay special attention to your personal safety when replacing the dust filter.

Installing the dust filter

1. Be sure to turn off the projector and unplug it

from power source.

2. As the arrows shown to the right, fit the filter

by aligning and inserting it into the projector slots. Make sure it clicks into place.

For first time installation:

3. Open the OSD menu and go to the ADVANCED > Filter Settings menu.

4. Press Enter and the Filter Settings page is displayed.

5. Highlight Filter Mode and press / to select On. The filter timer starts counting.

Set Filter Mode to On only when using the projector after the dust filer (optional accessory) is properly attached. Failing to do so will result in a shorter lamp life.

Obtaining the filter hour information

1. Open the OSD menu and go to the ADVANCED > Filter Settings menu.

2. Press Enter. The Filter Settings page is displayed.

3. You will see the Filter Hours information on the menu.

Cleaning the dust filter

1. Be sure to turn off the projector and unplug it from power source.

2. Remove the screws that secure the dust filter cover.

3. Remove the filter from the projector.

4. Use a small vacuum cleaner or a soft brush to sweep the dust on the filter away.

5. Re-install the dust filter.

Resetting the filter timer

6. Open the OSD menu and go to the ADVANCED > Filter Settings menu.

7. Press Enter and the Filter Settings page is displayed.

8. Highlight Reset Filter Hours and press Enter. A warning message is displayed

asking if you want to reset the filter timer.

9. Highlight Reset and press Enter. The lamp time will be reset to '0'.

CAUTION

Remember to set Filter Mode to Off in the ADVANCED > Filter Settings menu when using the projector with the dust filter removed. Setting Filter Mode to Off does not reset the filter timer.

The timer will continue counting the next time you fit the filter back on and set Filter Mode to On.

Lamp information

Getting to know the lamp hour

When the projector is in operation, the duration (in hours) of lamp usage is automatically calculated by the built-in timer.

To obtain the lamp hour information:

1. Open the OSD menu and go to the ADVANCED > Lamp Settings menu.

2. Press Enter and the Lamp Settings page is displayed.

3. You will see the Lamp Hours information on the menu.

4. To leave the menu, press Exit.

Extending lamp life

The projection lamp is a consumable item. To keep the lamp life as long as possible, you can do the following settings via the OSD menu.

Setting Lamp Mode

Using Eco mode reduces system noise and power consumption by 20%. If the Eco mode is selected, the light output will be reduced and result in darker projected pictures.

Setting the projector in Eco mode also extends the lamp operation life. To set Eco mode, go to the ADVANCED > Lamp Settings > Lamp Mode menu and press / to select Eco.

Or you can press Eco Mode on the remote control to select.

Setting Auto Power Off

This function allows the projector to turn off automatically after a set period of time once no input source is detected to prevent unnecessary waste of lamp life.

1. Open the OSD menu and go to the POWER MANAGEMENT > Smart Energy

menu.

2. Press Enter and the Smart Energy page is displayed.

3. Highlight Auto Power Off and press / .

4. If the preset time lengths are not suitable for your need, select Disable. The projector

will not automatically shut down in a certain time period.

Setting Sleep Timer

This function allows the projector to turn off automatically after a set period of time to prevent unnecessary waste of lamp life.

1. Open the OSD menu and go to the POWER MANAGEMENT > Smart Energy

menu.

2. Press Enter and the Smart Energy page is displayed.

3. Highlight Sleep Timer and press / .

4. If the preset time lengths are not suitable for your presentation, select Disable. The

projector will not automatically shut down in a certain time period.

Setting Power Saving

The projector lowers the power consumption if no input source is detected after 5 minutes to prevent unnecessary waste of lamp life. You can further decide if you would like the projector to turn off automatically after a set period of time.

1. Open the OSD menu and go to the POWER MANAGEMENT > Smart Energy

menu.

2. Press Enter and the Smart Energy page is displayed.

3. Highlight Power Saving and press / .

4. When Enable is selected, the projector lamp will be changed to Eco

mode after no signal is detected for 5 minutes.

Timing of replacing the lamp

Please install a new lamp or consult your dealer when the Lamp indicator light lights up. An old lamp may cause a malfunction in the projector and in some instances the lamp may explode.

CAUTION

The Lamp indicator light and Temperature indicator light will light up if the lamp becomes too hot. Turn the power off and let the projector cool for 45 minutes. If the Lamp indicator light or Temperature indicator light still lights up after turning the power back on, please contact your dealer. See "Indicators" on page 63 for details.

Replacing the lamp

Turn the power off and disconnect the projector from the power outlet. Please contact qualified service personnel for changing the lamp.

Indicators

Light Status & Description

Blue

Flashing

Blue Off Off

Blue

Flashing

Red Off Off

Blue Blue Blue

Blue

Flashing

Off Off Red

Blue Off Red

Off Red Off

Off Red Red

Off Red Blue

Off Red Purple

Red Red Red

Red Red Blue

Blue Red Red

Off Red Blue

Purple Red Red

Purple Red Blue

Off Blue Red

Off Off

Off Red

Power events

Stand-by mode

Powering up

Normal operation

Normal power-down cooling (3 sec)

Downloading

Burn in off

Lamp events

First Lamp-Lit error cooling (60 sec)

Lamp error in normal operation (30 sec)

CW start fail (30 sec)

Thermal events

Fan 1 error (the actual fan speed is +25% outside the desired speed.)

Fan 2 error (the actual fan speed is +25% outside the desired speed.)

Fan 3 error (the actual fan speed is +25% outside the desired speed.)

Fan 4 error (the actual fan speed is +25% outside the desired speed.)

Thermal sensor 1 open error (the remote diode has an open-circuit condition.)

Thermal sensor 2 open error (the remote diode has an open-circuit condition.)

Thermal sensor 1 short error (the remote diode has an short-circuit condition.)

Thermal sensor 2 short error (the remote diode has an short-circuit condition.)

Temperature 1 error (over limited temperature)

Temperature 2 error (over limited temperature)

Fan IC #1 I2C connection error

Troubleshooting

The projector does not turn on.

Cause Remedy

There is no power from the power cord.

Attempting to turn the projector on again during the cooling process.

No picture

Cause Remedy

The video source is not turned on or connected correctly.

The projector is not correctly connected to the input signal device.

The input signal has not been correctly selected.

Blurred image

Cause Remedy

The projection lens is not correctly focused. Adjust the focus of the lens using the focus ring.

The projector and the screen are not aligned properly.

Remote control does not work

Cause Remedy

The battery is out of power. Replace the battery with a new one.

There is an obstacle between the remote control and the projector.

You are too far away from the projector. Stand within 8 meters (26 feet) from the projector.

The remote control code on the projector and that on the remote control are not consistent.

Plug the power cord into the AC inlet on the projector, and plug the power cord into the power outlet. If the power outlet has a switch, make sure that it is switched on.

Wait until the cooling down process has completed.

Turn the video source on and check that the signal cable is connected correctly.

Check the connection.

Select the correct input signal with the Source key on the projector or remote control.

Adjust the projection angle and direction as well as the height of the projector if necessary.

Remove the obstacle.

Adjust the remote control code.

Specifications

ZOOM

FOCUS

469.5

139.8

316.24

164.10

291.20

286.20

3.50

8.16

133.10

Ceiling mount screws: M4 x 8 (Max. L = 8 mm)

Unit: mm

Dimensions

469.5 mm (W) x 139.8 mm (H) x 316.24 mm (D) (Including extrusions)

Ceiling mount installation

IR control table

Key Format Byte1 Byte2 Byte3 Byte4

PgDn NEC X3 F4 05 FA

PgUp NEC X3 F4 06 F9

Blank NEC X3 F4 07 F8

Auto sync NEC X3 F4 08 F7

Up NEC X3 F4 0B F4

Down NEC X3 F4 0C F3

Left NECX3F40EF1

Right NEC X3 F4 0F F0

Color Mode NEC X3 F4 10 EF

Mute NEC X3 F4 14 EB

Enter NEC X3 F4 15 EA

Power ON NEC X3 F4 17 E8

Presentation Timer NEC X3 F4 27 D8

Exit NEC X3 F4 28 D7

Eco Mode NEC X3 F4 2B D4

Menu NEC X3 F4 30 CF

Mouse NEC X3 F4 31 CE

Mouse Left NEC X3 F4 36 C9

Mouse Right NEC X3 F4 37 C8

Source NECX3F440BF

Pattern NEC X3 F4 55 AA

My button NEC X3 F4 56 A9

HDMI NEC X3 F4 58 A7

Volume+ NEC X3 F4 82 7D

Volume- NEC X3 F4 83 7C

Magnify NEC X3 F4 18 e7

Aspect NEC 83 F4 13 EC

Video NEC 83 F4 9F 60

Audio Mode NEC X3 F4 9E 61

COMP NEC X3 F4 41 be

Panel Key Lock NEC X3 F4 8E 71

Help NEC X3 F4 21 DE

Address code

Code 1 83F4

Code 2 93F4

Code 3 A3F4

Code 4 B3F4

Code 5 C3F4

Code 6 D3F4

Code 7 E3F4

Code 8 F3F4

RS232 command table

Pin Description Pin Description

1NC2RX

3TX4NC

5GND6NC

7RTSZ8CTSZ

9NC

Baud Rate 115200 bps (default)

Data Length 8 bit

Parity Check None

Stop Bit 1 bit

Flow Control None

RS-232 protocol

Function Status Action cmd

Turn on 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x00 0x00 0x5D

Turn off 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x01 0x00 0x5E

Power status

(on/off)

Execute 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x02 0x00 0x5F

Execute 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x2A 0x00 0x87

Splash Screen

Black

Splash Screen

Blue

Splash Screen

ViewSonic

Splash Screen

Screen

Capture

Splash Screen

Off

Splash Screen

status

Quick Power

Off Off

Quick Power

Off On

Quick Power

Off status

High Altitude

Mode Off

High Altitude

Mode On

High Altitude

Mode status

Normal 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x10 0x00 0x6D

Eco 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x10 0x01 0x6E

Lamp Mode

status

0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x11 0x00 0x5E

0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x0A 0x00 0x67

0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x0A 0x01 0x68

0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x0A 0x02 0x69

0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x0A 0x03 0x6A

0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x0A 0x04 0x6B

0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x11 0x0A 0x68

0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x0B 0x00 0x68

0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x0B 0x01 0x69

0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x11 0x0B 0x69

0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x0C 0x00 0x69

0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x0C 0x01 0x6A

0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x11 0x0C 0x6A

0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x11 0x10 0x6E

Power

Reset all

settings

Reset

Color

Settings

Spla sh

Screen

Quick

Power Off

High

Altitude

Mode

Lamp Mode

Write

Read

Write

Read

Write

Read

Write

Read

Write

Read

Message

Projector

Position

3D Sync

Invert

Contrast

Brightness

Write

Read

Write

Read

Write

Read

Write

Read

Write

Read Contrast ratio 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x12 0x02 0x61

Write

Read Brightness 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x12 0x03 0x62

Message Off 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x27 0x00 0x84

Message On 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x27 0x01 0x85

Message

status

Front Table 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x00 0x00 0x5E

Rear Table 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x00 0x01 0x5F

Rear Ceiling 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x00 0x02 0x60

Front Ceiling 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x00 0x03 0x61

projector

position status

OFF 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x20 0x00 0x7E

Auto 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x20 0x01 0x7F

Frame

Sequential

Frame

Packing

Top-Bottom 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x20 0x04 0x82

Side-by-Side 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x20 0x05 0x83

3D Sync

Status

Off 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x21 0x00 0x7F

On 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x21 0x01 0x80

3D Sync Invert

Status

Contrast

decrease

Contrast increase

Brightness

decrease

Brightness

increase

0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x11 0x27 0x85

0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x12 0x00 0x5F

0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x20 0x02 0x80

0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x20 0x03 0x81

0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x12 0x20 0x7F

0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x12 0x21 0x80

0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x02 0x00 0x60

0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x02 0x01 0x61

0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x03 0x00 0x61

0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x03 0x01 0x62

Aspect

ratio

Auto

Adjust

Horizontal

position

Vertical

position

Color

temperatur

Aspect ratio

Auto

Aspect ratio

4:3

Aspect ratio

16:9

Write

Read Aspect ratio 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x12 0x04 0x63

Write

Read

Write

Read

Write

Read

Aspect ratio

16:10

Aspect ratio Anamorphic

Aspect ratio

2.35:1

Aspect ratio

Panorama

Execute 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x05 0x00 0x63

Horizontal

position shift

right

Horizontal

position shift

left

Horizontal

position

Vertica l

position shift

Vertica l

position shift

down

read Vertical

position

color

temperature

Warm

color

temperature

Normal

color

temperature

Neutral

color

temperature

Cool

color

temperature

status

0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x04 0x00 0x62

0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x04 0x02 0x64

0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x04 0x03 0x65

0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x04 0x04 0x66

0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x04 0x05 0x67

0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x04 0x07 0x69

0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x04 0x08 0x6A

0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x06 0x01 0x65

0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x06 0x00 0x64

0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x12 0x06 0x65

0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x07 0x00 0x65

0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x07 0x01 0x66

0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x12 0x07 0x66

0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x08 0x00 0x66

0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x08 0x01 0x67

0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x08 0x02 0x68

0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x08 0x03 0x69

0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x12 0x08 0x67

Blank

Keystone-

Vertical

KeystoneHorizontal

Color mode

Primary

Color

Hue

Write

Read Blank status 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x12 0x09 0x68

Write

Read

Write

Read

Write

Read

Write

Read

Write

Read Hue 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x12 0x11 0x70

Blank on 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x09 0x01 0x68

Blank off 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x09 0x00 0x67

Decrease 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x0A 0x00 0x68

Increase 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x0A 0x01 0x69

Keystone

status

Decrease 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x31 0x00 0x8E

Increase 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x31 0x01 0x8F

Keystone

status

Brightest 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x0B 0x00 0x69

Movie 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x0B 0x01 0x6A

Standard 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x0B 0x04 0x6D

ViewMatch

sRGB

Dynamic 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x0B 0x08 0x71

DICOM SIM 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x0B 0x0a 0x73

Preset mode

status

Primary color

status

Hue decrease 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x11 0x00 0x6F

Hue increase 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x11 0x01 0x70

0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x12 0x0A 0x69

0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x11 0x31 0x8F

0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x0B 0x05 0x6E

0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x12 0x0B 0x6A

0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x10 0x00 0x6E

0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x10 0x01 0x6F

0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x10 0x02 0x70

0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x10 0x03 0x71

0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x10 0x04 0x72

0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x10 0x05 0x73

0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x12 0x10 0x6F

Saturation

Gain

Freeze

Source

input

Quick Auto

Mute

Volume

Saturation

Write

Read Saturation 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x12 0x12 0x71

Write

Read Gain 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x12 0x13 0x72

Write

Read Freeze status 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x13 0x00 0x60

Write

Read Source 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x13 0x01 0x61

Write

Read

Write

Read Mute status 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x14 0x00 0x61

Write

Read Volume 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x14 0x03 0x64

decrease

Saturation

increase

Gain decrease 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x13 0x00 0x71

Gain increase 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x13 0x01 0x72

Freeze on 0x06 0x14 0x00 0x04 0x00 0x34 0x13 0x00 0x01 0x60

Freeze off 0x06 0x14 0x00 0x04 0x00 0x34 0x13 0x00 0x00 0x5F

Input source

VGA

Input source

VGA2

Input source

HDMI

Input source

HDMI/MHL

Input source

Composite

Input source

SVIDEO

Quick Auto

Search on

Quick Auto

Search off

Quick Auto

Search status

Mute on 0x06 0x14 0x00 0x04 0x00 0x34 0x14 0x00 0x01 0x61

Mute off 0x06 0x14 0x00 0x04 0x00 0x34 0x14 0x00 0x00 0x60

Increase

Volum e

Decrease

Volum e

0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x12 0x00 0x70

0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x12 0x01 0x71

0x06 0x14 0x00 0x04 0x00 0x34 0x13 0x01 0x00 0x60

0x06 0x14 0x00 0x04 0x00 0x34 0x13 0x01 0x08 0x68

0x06 0x14 0x00 0x04 0x00 0x34 0x13 0x01 0x03 0x63

0x06 0x14 0x00 0x04 0x00 0x34 0x13 0x01 0x07 0x67

0x06 0x14 0x00 0x04 0x00 0x34 0x13 0x01 0x05 0x65

0x06 0x14 0x00 0x04 0x00 0x34 0x13 0x01 0x06 0x66

0x06 0x14 0x00 0x04 0x00 0x34 0x13 0x02 0x01 0x62

0x06 0x14 0x00 0x04 0x00 0x34 0x13 0x02 0x00 0x61

0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x13 0x02 0x62

0x06 0x14 0x00 0x04 0x00 0x34 0x14 0x01 0x00 0x61

0x06 0x14 0x00 0x04 0x00 0x34 0x14 0x02 0x00 0x62

Language

Tiếng Việt

Write

0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x00 0x61

0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x01 0x62

0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x02 0x63

0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x03 0x64

0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x04 0x65

0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x05 0x66

0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x06 0x67

0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x07 0x68

0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x08 0x69

0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x09 0x6A

0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x0a 0x6B

0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x0b 0x6C

0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x0c 0x6D

0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x0d 0x6E

0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x0e 0x6F

0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x0f 0x70

Lamp

Time

0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x10 0x71

0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x11 0x72

0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x12 0x73

0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x13 0x74

0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x14 0x75

0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x15 0x76

Read Language 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x15 0x00 0x62

Write

Read

Reset Lamp

usage hour

Lamp usage

hour

0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x01 0x00 0x62

0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x15 0x01 0x63

HDMI

Format

HDMI

Range

CEC

Error

status

Brilliant

Color

RGB 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x28 0x00 0x85

Write

Read

Write

Read

Write

Read CEC status 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x11 0x2B 0x89

Read

Write

Read

YUV 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x28 0x01 0x86

Auto 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x28 0x02 0x87

HDMI Format

status

Enhanced 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x29 0x00 0x86

Normal 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x29 0x01 0x87

Auto 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x29 0x02 0x88

HDMI Range

status

Off 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x2B 0x00 0x88

On 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x2B 0x01 0x89

Read error

status

Brilliant Color

status

0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x11 0x28 0x86

0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x11 0x29 0x87

0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x0C 0x0D 0x66

0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x0F 0x00 0x6D

0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x0F 0x01 0x6E

0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x0F 0x02 0x6F

0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x0F 0x03 0x70

0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x0F 0x04 0x71

0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x0F 0x05 0x72

0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x0F 0x06 0x73

0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x0F 0x07 0x74

0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x0F 0x08 0x75

0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x0F 0x09 0x76

0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x0F 0x0A 0x77

0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x12 0x0F 0x6E

Remote

Control

code

Screen

Color

Over Scan

Write

Read

Write

Read

Write

Read

code 1 0x06 0x14 0x00 0x04 0x00 0x34 0x0C 0x48 0x00 0xA0

code 2 0x06 0x14 0x00 0x04 0x00 0x34 0x0C 0x48 0x01 0xA1

code 3 0x06 0x14 0x00 0x04 0x00 0x34 0x0C 0x48 0x02 0xA2

code 4 0x06 0x14 0x00 0x04 0x00 0x34 0x0C 0x48 0x03 0xA3

code 5 0x06 0x14 0x00 0x04 0x00 0x34 0x0C 0x48 0x04 0xA4

code 6 0x06 0x14 0x00 0x04 0x00 0x34 0x0C 0x48 0x05 0xA5

code 7 0x06 0x14 0x00 0x04 0x00 0x34 0x0C 0x48 0x06 0xA6

code 8 0x06 0x14 0x00 0x04 0x00 0x34 0x0C 0x48 0x07 0xA7

Remote

Control code

status

Screen color

Off

Blackboard 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x32 0x01 0x90

Greenboard 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x32 0x02 0x91

Whiteboard 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x32 0x03 0x92

Screen Color

status

Overscan Off 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x33 0x00 0x90

Overscan 1 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x33 0x01 0x91

Overscan 2 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x33 0x02 0x92

Overscan 3 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x33 0x03 0x93

Overscan 4 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x33 0x04 0x94

Overscan 5 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x33 0x05 0x95

Overscan

status

0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x0C 0x048 0xA1

0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x32 0x00 0x8F

0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x11 0x32 0x90

0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x11 0x33 0x91

Remote

Key

Menu 0x02 0x14 0x00 0x04 0x00 0x34 0x02 0x04 0x0F 0x61

Exit 0x02 0x14 0x00 0x04 0x00 0x34 0x02 0x04 0x13 0x65

Up 0x02 0x14 0x00 0x04 0x00 0x34 0x02 0x04 0x0B 0x5D

Down 0x02 0x14 0x00 0x04 0x00 0x34 0x02 0x04 0x0C 0x5E

Left 0x02 0x14 0x00 0x04 0x00 0x34 0x02 0x04 0x0D 0x5F

Write

Right 0x02 0x14 0x00 0x04 0x00 0x34 0x02 0x04 0x0E 0x60

Source 0x02 0x14 0x00 0x04 0x00 0x34 0x02 0x04 0x04 0x56

Enter 0x02 0x14 0x00 0x04 0x00 0x34 0x02 0x04 0x15 0x67

Auto 0x02 0x14 0x00 0x04 0x00 0x34 0x02 0x04 0x08 0x5A

My Button 0x02 0x14 0x00 0x04 0x00 0x34 0x02 0x04 0x11 0x63

Timing chart

Analog RGB

Signal Resolution (dots) Aspect Ratio Refresh Rate (Hz)

VGA 640 x 480 4:3 60/72/75/85

SVGA 800 x 600 4:3 60/72/75/85

XGA

WXGA

Quad-VGA 1280 x 960 4:3 60/85

SXGA 1280 x 1024 5:4 60

SXGA+ 1400 x 1050 4:3 60

WXGA+ 1440 x 900 16:10 60

UXGA 1600 x 1200 4:3 60

WSXGA+ 1680 x 1050 16:10 60

HD 1280 x 720 16:9 60

MAC 13" 640 x 480 4:3 67

1024 x 768 4:3 60/70/75/85

1152 x 864 4:3 75

1280 x 768 15:9 60

1280 x 800 16:10 60/75/85

1360 x 768 16:9 60

MAC 16" 832 x 624 4:3 75

MAC 19" 1024 x 768 4:3 75

MAC 21" 1152 x 870 4:3 75

HDTV (1080p) 1920 x 1080 16:9 60

WUXGA 1920 x 1200 16:10 60

HDMI

Signal Resolution (dots) Aspect Ratio Refresh Rate (Hz)

VGA 640 x 480 4:3 60

SVGA 800 x 600 4:3 60

XGA 1024 x 768 4:3 60

1280 x 768 15:9 60

WXGA

Quad-VGA 1280 x 960 4:3 60

SXGA 1280 x 1024 5:4 60

SXGA+ 1400 x 1050 4:3 60

WXGA+ 1440 x 900 16:10 60

WSXGA+ 1680 x 1050 16:10 60

HDTV (1080p) 1920 x 1080 16:9 50 / 60

HDTV (1080i) 1920 x 1080 16:9 50 / 60

HDTV (720p) 1280 x 720 16:9 50 / 60

SDTV (480p) 720 x 480 4:3 / 16:9 60

SDTV (576p) 720 x 576 4:3 / 16:9 50

SDTV (480i) 720 x 480 4:3 / 16:9 60

SDTV (576i) 720 x 576 4:3 / 16:9 50

1280 x 800 16:10 60

1360 x 768 16:9 60

WUXGA 1920 x 1200 16:10 60

3D (HDMI signal included)

Signal Resolution (dots) Aspect Ratio Refresh Rate (Hz)

SVGA 800 x 600 4:3 60* / 120**

XGA 1024 x 768 4:3 60* / 120**

HD 1280 x 720 16:9 60* / 120**

WXGA 1280 x 800 16:9 60* / 120**

for Video Signal

Signal Resolution (dots) Aspect Ratio Refresh Rate (Hz)

SDTV (480i)*** 720 x 480 4:3 / 16:9 60

60Hz signals are supported for

** 120 Hz signals are supported for Frame Sequential format only.

*** Video signal (SDTV 480i) is supported for Frame Sequential format only.

Side-by-Side, Top-Bottom

, and

Frame Sequential

HDMI 3D

In Frame packing format

Signal Resolution (dots) Aspect Ratio Refresh Rate (Hz)

1080p 1920 x 1080 16:9 23.98/24

720p 1280 x 720 16:9 50/59.94/60

In Side by side format

Signal Resolution (dots) Aspect Ratio Refresh Rate (Hz)

formats.

1080i 1920 x 1080 16:9 50/59.94/60

In Top and Bottom format

Signal Resolution (dots) Aspect Ratio Refresh Rate (Hz)

1080p 1920 x 1080 16:9 23.98/24

720p 1280 x 720 16:9 50/59.94/60

Component video

Signal Resolution (dots) Aspect Ratio Refresh Rate (Hz)

HDTV (1080p) 1920 x 1080 16:9 50 / 60

HDTV (1080i) 1920 x 1080 16:9 50 / 60

HDTV (720p) 1280 x 720 16:9 50 / 60

SDTV (480p) 720 x 480 4:3 / 16:9 60

SDTV (576p) 720 x 576 4:3 / 16:9 50

SDTV (480i) 720 x 480 4:3 / 16:9 60

SDTV (576i) 720 x 576 4:3 / 16:9 50

Composite video

Signal Aspect Ratio Refresh Rate (Hz)

NTSC 4:3 60

PAL 4: 3 5 0

PAL60 4:3 60

SECAM 4:3 50

Projector specifications

All specifications are subject to change without notice.

Not all models can be purchased in your region.

Model name Pro8510L Pro8520WL Pro8530HDL Pro8800WUL

Product Specification

Resolution

Throw ratio Display system 1-CHIP DMD Lamp Type 370 W (RCL-103)

Input connector

RGB-in 2 Component input shared with RGB-in S-Video 1 Composite input 1 Audio-in 2 RCA R&L 1 Microphone 1 (share with audio in 2) Mini USB 1 HDMI (1.4a) 3 HDMI/MHL 3D VESA 1

Output connector

RGB-out 1 Audio-out 1 Speaker 10 watt x 2 USB type A (5V/

2A) USB microUSB

Wire (5V/2A)

Control terminal

RS-232 serial control

LAN RJ45 x 1 12V Trigger 1 IR receiver 2 (Font x1/Top x1) IR connector 1

Mechanical

Net Weight 6.3 Kg (13.9 lbs)

Electircal

Power Source AC100–240V, 50–60 Hz Power

Consumption

0.55” XGA (1024 x 768)

1.41~2.25

0.65” WXGA (1280 x 800)

1.12~1.8 1.07~1.71

STD: 573.8 W (Max); ECO: 468.85W (Typical);

< 0.5 W (Standby)

0.65” 1080p

(1920 x 1080)

1 (dongle)

9 pin x 1

0.67” WUXGA (1920 x 1200)

Environmental Requirements

Operating Temperature

Operating Altitude 0–1499 m at 5°C–35°C

1500–3000 m at 5°C–25°C (with High Altitude Mode on)

Operating Relative Humidity

0°C–40°C at sea level

10%–90% (without condensation)

Copyright information

Copyright 2016. All rights reserved. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system or translated into any language or computer language, in any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise, without the prior written permission of ViewSonic Corporation.

Disclaimer

ViewSonic Corporation makes no representations or warranties, either expressed or implied, with respect to the contents hereof and specifically disclaims any warranties, merchantability or fitness for any particular purpose. Further, ViewSonic Corporation reserves the right to revise this publication and to make changes from time to time in the contents hereof without obligation to notify any person of such revision or changes.

*DLP and Digital Micromirror Device (DMD) are trademarks of Texas Instruments. Others are copyrights of their respective companies or organizations.

Customer Support

For technical support or product service, see the table below or contact your reseller.

Note : You will need the product serial number.

Country/Region Website

Australia New Zealand

Canada www.viewsonic.com

Europe www.viewsoniceurope.com www.viewsoniceurope.com/uk/support/call-desk/ Hong Kong www.hk.viewsonic.com T= 852 3102 2900 service@hk.viewsonic.com India www.in.viewsonic.com T= 1800 419 0959 service@in.viewsonic.com Korea ap.viewsonic.com/kr/ T= 080 333 2131 service@kr.viewsonic.com Latin America

(Argentina) Latin America

(Chile) Latin America

(Columbia) Latin America

(Mexico) Nexus Hightech Solutions, Cincinnati #40 Desp. 1 Col. De los Deportes Mexico D.F.

Tel: 55) 6547-6454 55)6547-6484 Other places please refer to http://www.viewsonic.com/la/soporte/servicio-tecnico#mexico

Latin America (Peru)

Macau www.hk.viewsonic.com T= 853 2870 0303 service@hk.viewsonic.com Middle East ap.viewsonic.com/me/ Contact your reseller service@ap.viewsonic.com

Puerto Rico & Virgin Islands

Singapore/ Malaysia/Thailand

South Africa ap.viewsonic.com/za/ Contact your reseller service@ap.viewsonic.com

United States www.viewsonic.com

www.viewsonic.com.au

www.viewsonic.com/la/

www.viewsonic.com

www.ap.viewsonic.com T= 65 6461 6044 service@sg.viewsonic.com

T= Telephone C = CHAT ONLINE

AUS= 1800 880 818 NZ= 0800 008 822

T (Toll-Free)= 1-866-463-4775 T (Toll)= 1-424-233-2533

C= http://www.viewsonic.com/

la/soporte/servicio-tecnico

C= http://www.viewsonic.com/

la/soporte/servicio-tecnico

C= http://www.viewsonic.com/

la/soporte/servicio-tecnico

C= http://www.viewsonic.com/

la/soporte/servicio-tecnico

C= http://www.viewsonic.com/

la/soporte/servicio-tecnico

T= 1-800-688-6688 (English) C= http://www.viewsonic.com/

la/soporte/servicio-tecnico

T (Toll-Free)= 1-800-688-6688 T (Toll)= 1-424-233-2530

service@au.viewsonic.com

service.ca@viewsonic.com

soporte@viewsonic.com

service.us@viewsonic.com soporte@viewsonic.com

service.us@viewsonic.com

Limited Warranty

ViewSonic® Projector

What the warranty covers:

ViewSonic warrants its products to be free from defects in material and workmanship, under normal use, during the warranty period. If a product proves to be defective in material or workmanship during the warranty period, ViewSonic will, at its sole option, repair or replace the product with a like product. Replacement product or parts may include remanufactured or refurbished parts or components.

Limited Three (3) year General Warranty

Subject to the more limited one (1) year warranty set out below, North and South America: Three (3) years warranty for all parts excluding the lamp, three (3) years

IRUODERUDQGRQH\HDUIRUWKHRULJLQDOODPSIURPWKHGDWHRIWKH¿UVWFRQVXPHU

purchase. Other regions or countries: Please check with your local dealer or local ViewSonic

RI¿FHIRUWKHZDUUDQW\LQIRUPDWLRQ

Limited One (1) year Heavy Usage Warranty:

Under heavy usage settings, where a projector’s use includes more than fourteen (14) hours average daily usage, North and South America: One (1) year warranty for all parts excluding the lamp, one (1) year for labor, and ninety (90) days for the

RULJLQDOODPSIURPWKHGDWHRIWKH¿UVWFRQVXPHUSXUFKDVH(XURSH2QH\HDU

warranty for all parts excluding the lamp, one (1) year for labor, and ninety (90) days

IRUWKHRULJLQDOODPSIURPWKHGDWHRIWKH¿UVWFRQVXPHUSXUFKDVH

Other regions or countries: Please check with your local dealer or local ViewSonic

RI¿FHIRUWKHZDUUDQW\LQIRUPDWLRQ /DPSZDUUDQW\VXEMHFWWRWHUPVDQGFRQGLWLRQVYHUL¿FDWLRQDQGDSSURYDO$SSOLHVWR

manufacturer’s installed lamp only. All accessory lamps purchased separately are warranted for 90 days.

Who the warranty protects:

7KLVZDUUDQW\LVYDOLGRQO\IRUWKH¿UVWFRQVXPHUSXUFKDVHU

What the warranty does not cover:

$Q\SURGXFWRQZKLFKWKHVHULDOQXPEHUKDVEHHQGHIDFHGPRGL¿HGRUUHPRYHG

2. Damage, deterioration, failure, or malfunction resulting from:

D$FFLGHQWDEXVHPLVXVHQHJOHFW¿UHZDWHUOLJKWQLQJRURWKHUDFWVRIQDWXUH

LPSURSHUPDLQWHQDQFHXQDXWKRUL]HGSURGXFWPRGL¿FDWLRQRUIDLOXUHWRIROORZ

instructions supplied with the product.

E2SHUDWLRQRXWVLGHRISURGXFWVSHFL¿FDWLRQV

c. Operation of the product for other than the normal intended use or not under

normal conditions. d. Repair or attempted repair by anyone not authorized by ViewSonic. e. Any damage of the product due to shipment. f. Removal or installation of the product.

J&DXVHVH[WHUQDOWRWKHSURGXFWVXFKDVHOHFWULFSRZHUÀXFWXDWLRQVRUIDLOXUH K8VHRIVXSSOLHVRUSDUWVQRWPHHWLQJ9LHZ6RQLF¶VVSHFL¿FDWLRQV

i. Normal wear and tear. j. Any other cause which does not relate to a product defect.

3. Removal, installation, and set-up service charges.

How to get service:

1. For information about receiving service under warranty, contact ViewSonic Customer Support (please refer to “Customer Support” page). You will need to provide your product’s serial number.

2. To obtain warranted service, you will be required to provide (a) the original dated sales slip, (b) your name, (c) your address, (d) a description of the problem, and (e) the serial number of the product.

3. Take or ship the product freight prepaid in the original container to an authorized ViewSonic service center or ViewSonic.

4. For additional information or the name of the nearest ViewSonic service center, contact ViewSonic.

Limitation of implied warranties:

There are no warranties, express or implied, which extend beyond the description

FRQWDLQHGKHUHLQLQFOXGLQJWKHLPSOLHGZDUUDQW\RIPHUFKDQWDELOLW\DQG¿WQHVVIRUD

particular purpose.

Exclusion of damages:

ViewSonic’s liability is limited to the cost of repair or replacement of the product. ViewSonic shall not be liable for:

1. Damage to other property caused by any defects in the product, damages based

XSRQLQFRQYHQLHQFHORVVRIXVHRIWKHSURGXFWORVVRIWLPHORVVRISUR¿WVORVVRI

business opportunity, loss of goodwill, interference with business relationships, or other commercial loss, even if advised of the possibility of such damages.

2. Any other damages, whether incidental, consequential or otherwise.

3. Any claim against the customer by any other party.

Effect of local law:

7KLVZDUUDQW\JLYHV\RXVSHFL¿FOHJDOULJKWVDQG\RXPD\DOVRKDYHRWKHUULJKWV

which vary from local authority. Some local governances do not allow limitations on implied warranties and/or do not allow the exclusion of incidental or consequential damages, so the above limitations and exclusions may not apply to you.

Sales outside the U.S.A. and Canada:

For warranty information and service on ViewSonic products sold outside of the U.S.A. and Canada, contact ViewSonic or your local ViewSonic dealer. The warranty period for this product in mainland China (Hong Kong, Macao and Taiwan Excluded) is subject to the terms and conditions of the Maintenance Guarantee Card. For users in Europe and Russia, full details of warranty provided can be found in www.viewsoniceurope.com under Support/Warranty Information.

Projector Warranty Term Template In UG VSC_TEMP_2005

Mexico Limited Warranty

What the warranty covers:

How long the warranty is effective:

3 years for all parts excluding the lamp, 3 years for labor, 1 year for the original lamp from the date of

WKH¿UVWFRQVXPHUSXUFKDVH /DPSZDUUDQW\VXEMHFWWRWHUPVDQGFRQGLWLRQVYHUL¿FDWLRQDQGDSSURYDO$SSOLHVWRPDQXIDFWXUHU¶V

installed lamp only. All accessory lamps purchased separately are warranted for 90 days.

Who the warranty protects:

7KLVZDUUDQW\LVYDOLGRQO\IRUWKH¿UVWFRQVXPHUSXUFKDVHU

What the warranty does not cover:

 $Q\SURGXFWRQZKLFKWKHVHULDOQXPEHUKDVEHHQGHIDFHGPRGL¿HGRUUHPRYHG

2. Damage, deterioration or malfunction resulting from:

D$FFLGHQWPLVXVHQHJOHFW¿UHZDWHUOLJKWQLQJRURWKHUDFWVRIQDWXUHXQDXWKRUL]HGSURGXFW

PRGL¿FDWLRQXQDXWKRUL]HGDWWHPSWHGUHSDLURUIDLOXUHWRIROORZLQVWUXFWLRQVVXSSOLHGZLWKWKH

product.

b. Any damage of the product due to shipment.

F&DXVHVH[WHUQDOWRWKHSURGXFWVXFKDVHOHFWULFDOSRZHUÀXFWXDWLRQVRUIDLOXUH G8VHRIVXSSOLHVRUSDUWVQRWPHHWLQJ9LHZ6RQLF¶VVSHFL¿FDWLRQV

e. Normal wear and tear. f. Any other cause which does not relate to a product defect.

3. Any product exhibiting a condition commonly known as “image burn-in” which results when a static image is displayed on the product for an extended period of time.

4. Removal, installation, insurance, and set-up service charges.

How to get service:

For information about receiving service under warranty, contact ViewSonic Customer Support (Please refer to the attached Customer Support page). You will need to provide your product’s serial number, so please record the product information in the space provided below on your purchase for your future use. Please retain your receipt of proof of purchase to support your warranty claim. For Your Records Product Name: ________________________ Model Number: ____________________________ Document Number: ____________________ Serial Number: ____________________________ Purchase Date: ________________________ Extended Warranty Purchase? _____________(Y/N) If so, what date does warranty expire? __________

1. To obtain warranty service, you will be required to provide (a) the original dated sales slip, (b) your name, (c) your address, (d) a description of the problem, and (e) the serial number of the product.

2. Take or ship the product in the original container packaging to an authorized ViewSonic service center.

3. Round trip transportation costs for in-warranty products will be paid by ViewSonic.

Limitation of implied warranties:

There are no warranties, express or implied, which extend beyond the description contained herein

LQFOXGLQJWKHLPSOLHGZDUUDQW\RIPHUFKDQWDELOLW\DQG¿WQHVVIRUDSDUWLFXODUSXUSRVH

Exclusion of damages:

ViewSonic’s liability is limited to the cost of repair or replacement of the product. ViewSonic shall not be liable for:

1. Damage to other property caused by any defects in the product, damages based upon

LQFRQYHQLHQFHORVVRIXVHRIWKHSURGXFWORVVRIWLPHORVVRISUR¿WVORVVRIEXVLQHVVRSSRUWXQLW\

loss of goodwill, interference with business relationships, or other commercial loss, even if advised of the possibility of such damages.

2. Any other damages, whether incidental, consequential or otherwise.

3. Any claim against the customer by any other party.

4. Repair or attempted repair by anyone not authorized by ViewSonic.

ViewSonic® Projector

Contact Information for Sales & Authorized Service (Centro Autorizado de Servicio) within Mexico:

Name, address, of manufacturer and importers:

México, Av. de la Palma #8 Piso 2 Despacho 203, Corporativo Interpalmas, Col. San Fernando Huixquilucan, Estado de México Tel: (55) 3605-1099 http://www.viewsonic.com/la/soporte/index.htm

NÚMERO GRATIS DE ASISTENCIA TÉCNICA PARA TODO MÉXICO: 001.866.823.2004

Hermosillo:

Distribuciones y Servicios Computacionales SA de CV. Calle Juarez 284 local 2 Col. Bugambilias C.P: 83140 Tel: 01-66-22-14-9005 E-Mail: disc2@hmo.megared.net.mx

Puebla, Pue. (Matriz):

RENTA Y DATOS, S.A. DE C.V. Domicilio: 29 SUR 721 COL. LA PAZ 72160 PUEBLA, PUE. Tel: 01(52).222.891.55.77 CON 10 LINEAS E-Mail: datos@puebla.megared.net.mx

Chihuahua

Soluciones Globales en Computación C. Magisterio # 3321 Col. Magisterial Chihuahua, Chih. Tel: 4136954 E-Mail: Cefeo@soluglobales.com

Distrito Federal:

QPLUS, S.A. de C.V. Av. Coyoacán 931 Col. Del Valle 03100, México, D.F. Tel: 01(52)55-50-00-27-35 E-Mail : gacosta@qplus.com.mx

Guerrero Acapulco

GS Computación (Grupo Sesicomp) Progreso #6-A, Colo Centro 39300 Acapulco, Guerrero Tel: 744-48-32627

MERIDA:

ELECTROSER Av Reforma No. 403Gx39 y 41 Mérida, Yucatán, México CP97000 Tel: (52) 999-925-1916 E-Mail: rrrb@sureste.com

Tijuana:

STD Av Ferrocarril Sonora #3780 L-C Col 20 de Noviembre Tijuana, Mexico

Villahermosa:

Compumantenimietnos Garantizados, S.A. de C.V. AV. GREGORIO MENDEZ #1504 COL, FLORIDA C.P. 86040 Tel: 01 (993) 3 52 00 47 / 3522074 / 3 52 20 09 E-Mail: compumantenimientos@prodigy.net.mx

Veracruz, Ver.:

CONEXION Y DESARROLLO, S.A DE C.V. Av. Americas # 419 ENTRE PINZÓN Y ALVARADO Fracc. Reforma C.P. 91919 Tel: 01-22-91-00-31-67 E-Mail: gacosta@qplus.com.mx

Cuernavaca

Compusupport de Cuernavaca SA de CV Francisco Leyva # 178 Col. Miguel Hidalgo C.P. 62040, Cuernavaca Morelos Tel: 01 777 3180579 / 01 777 3124014 E-Mail: aquevedo@compusupportcva.com

Guadalajara, Jal.:

SERVICRECE, S.A. de C.V. Av. Niños Héroes # 2281 Col. Arcos Sur, Sector Juárez 44170, Guadalajara, Jalisco Tel: 01(52)33-36-15-15-43 E-Mail: mmiranda@servicrece.com

Monterrey:

Global Product Services Mar Caribe # 1987, Esquina con Golfo Pérsico Fracc. Bernardo Reyes, CP 64280 Monterrey N.L. México Tel: 8129-5103 E-Mail: aydeem@gps1.com.mx

Oaxaca, Oax.:

CENTRO DE DISTRIBUCION Y SERVICIO, S.A. de C.V. Murguía # 708 P.A., Col. Centro, 68000, Oaxaca Tel: 01(52)95-15-15-22-22 Fax: 01(52)95-15-13-67-00 E-Mail. gpotai2001@hotmail.com

FOR USA SUPPORT:

ViewSonic Corporation 14035 Pipeline Ave. Chino, CA 91710, USA

7HO(QJOLVK6SDQLVK

E-Mail: http://www.viewsonic.com

Projector Mexico Warranty Term Template In UG VSC_TEMP_2006

ViewSonic Pro8800WUL, Pro8530HDL, Pro8510L User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual

Table of contents

Important safety instructions

Safety Instructions

Safety instructions for ceiling mounting of the projector

Introduction

Projector features

Shipping contents

Controls and functions

Projector

Remote control

Positioning your projector

Choosing a location

Projection dimensions

For models with a 4:3 native aspect ratio

For models with a 16:10 native aspect ratio

For models with a 16:9 native aspect ratio

Shifting the projection lens vertically

Connection

Connecting a computer or monitor

Connecting a computer

Connecting a monitor

Connecting Video source devices

Connecting an HDMI device

Connecting a Component Video source device

Connecting an S-Video source device

Connecting a composite Video source device

Playing sound through the projector

Using the cable management cover

Operation

Starting up the projector

Using the menus

Utilizing the password function

Setting a password

If you forget the password

Entering the password recall procedure

Changing the password

Disabling the password function

Switching input signal

Adjusting the projected image

Adjusting the projection angle

Auto-adjusting the image

Fine-tuning the image clarity

Correcting keystone

Adjusting 4 corners

Magnifying and searching for details

Selecting the aspect ratio

Optimizing the image

Selecting a picture mode

Using Screen Color

Fine-tuning the image quality in user modes

Setting the presentation timer

Hiding the image

Locking control keys

Creating your own startup screen

Operating in a high altitude environment

Using the CEC function

Using the 3D functions

Controlling the projector through a LAN environment

Using the projector in standby mode

Adjusting the sound

Shutting down the projector

Menu operation

Menu system

Description of each menu

Maintenance

Care of the projector

Cleaning the lens

Cleaning the projector case

Storing the projector

Transporting the projector

Using the dust filter (optional accessory)

Lamp information

Getting to know the lamp hour

Extending lamp life

Timing of replacing the lamp

Replacing the lamp