ViewSonic PRO8520HD User Manual

Page 1

Pro8520HD DLP Projector

User Guide

IMPORTANT: Please read this User Guide to obtain important information on installing and using your product in a safe manner, as well as registering your product for future service. Warranty information contained in this User Guide will describe your limited coverage from ViewSonic Corporation, which is also found on our web site at http://

www.viewsonic.com in English, or in specic languages using the Regional selection

box in the upper right corner of our website. “Antes de operar su equipo lea cu idadosamente las instrucciones en este manual”

Model No. VS14804

Page 2

Compliance Information

FCC Statement

This device complies with part 15 of FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

y Reorient or relocate the receiving antenna. y Increase the separation between the equipment and receiver. y Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected.

y Consult the dealer or an experienced radio/TV technician for help.

Warning: You are cautioned that changes or modications not expressly approved

by the party responsible for compliance could void your authority to operate the equipment.

For Canada

CAN ICES-3 (B)/NMB-3(B)

CE Conformity for European Countries

The device complies with the EMC Directive 2004/108/EC and Low Voltage Directive 2006/95/EC.

Following information is only for EU-member states:

The mark is in compliance with the Waste Electrical and Electronic Equipment Directive 2002/96/EC (WEEE).

The mark indicates the requirement NOT to dispose the equipment including any spent or discarded batteries or accumulators as unsorted municipal waste, but use the return and collection systems available.

If the batteries, accumulators and button cells included with this equipment, display the chemical symbol Hg, Cd, or Pb, then it means that the battery has a heavy metal content of more than 0.0005% Mercury or more than,

0.002% Cadmium, or more than 0.004% Lead.

Page 3

Important Safety Instructions

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this unit near water.

6. Clean with a soft, dry cloth.

7. Do not block any ventilation openings. Install the unit in accordance with the manufacturer’s instructions.

8. Do not install near any heat sources such as radiators, heat registers, stoves,

or other devices (including ampliers) that produce heat.

9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade and the third prong are provided for your safety. If the provided plug does not t into your outlet, consult an electrician for replacement of the obsolete outlet.

10. Protect the power cord from being walked on or pinched particularly at plugs.

Convenience receptacles and the point where they exit from the unit. Be sure that the power outlet is located near the unit so that it is easily accessible.

11. Only use attachments/accessories specied by the manufacturer.

12. Use only with the cart, stand, tripod, bracket, or table specied by

the manufacturer, or sold with the unit. When a cart is used, use caution when moving the cart/unit combination to avoid injury from tipping over.

13. Unplug this unit when unused for long periods of time.

14. Refer all servicing to qualied service personnel. Servicing is required when the

unit has been damaged in any way, such as: if the power-supply cord or plug is damaged, if liquid is spilled onto or objects fall into the unit, if the unit is exposed to rain or moisture, or if the unit does not operate normally or has been dropped.

Page 4

Declaration of RoHS2 Compliance

This product has been designed and manufactured in compliance with Directive 2011/65/EU of the European Parliament and the Council on restriction of the use of certain hazardous substances in electrical and electronic equipment (RoHS2 Directive) and is deemed to comply with the maximum concentration values issued by the European Technical Adaptation Committee (TAC) as shown below:

Substance

Lead (Pb) 0.1% < 0.1% Mercury (Hg) 0.1% < 0.1% Cadmium (Cd) 0.01% < 0.01%

Hexavalent Chromium (Cr Polybrominated biphenyls (PBB) 0.1% < 0.1% Polybrominated diphenyl ethers (PBDE) 0.1% < 0.1%

) 0.1% < 0.1%

Proposed Maximum Concentration

Actual Concentration

Certain components of products as stated above are exempted under the Annex III of the RoHS2 Directives as noted below:

Examples of exempted components are:

1. Mercury in cold cathode uorescent lamps and external electrode uorescent

lamps (CCFL and EEFL) for special purposes not exceeding (per lamp): (1) Short length (≦500 mm): maximum 3.5 mg per lamp. (2) Medium length (＞500 mm and ≦1,500 mm): maximum 5 mg per lamp. (3) Long length (＞1,500 mm): maximum 13 mg per lamp.

2. Lead in glass of cathode ray tubes.

3. Lead in glass of uorescent tubes not exceeding 0.2% by weight.

4. Lead as an alloying element in aluminium containing up to 0.4% lead by weight.

5. Copper alloy containing up to 4% lead by weight.

6. Lead in high melting temperature type solders (i.e. lead-based alloys containing

85% by weight or more lead).

7. Electrical and electronic components containing lead in a glass or ceramic other

than dielectric ceramic in capacitors, e.g. piezoelectronic devices, or in a glass or ceramic matrix compound.

iii

Page 5

Copyright © ViewSonic® Corporation, 2013. All rights reserved. Macintosh and Power Macintosh are registered trademarks of Apple Inc. Microsoft, Windows, Windows NT, and the Windows logo are registered trademarks of Microsoft Corporation in the United States and other countries. ViewSonic, the three birds logo, OnView, ViewMatch, and ViewMeter are registered trademarks of ViewSonic Corporation. VESA is a registered trademark of the Video Electronics Standards Association. DPMS and DDC are trademarks of VESA. PS/2, VGA and XGA are registered trademarks of International Business Machines Corporation. Disclaimer: ViewSonic Corporation shall not be liable for technical or editorial errors or omissions contained herein; nor for incidental or consequential damages resulting from furnishing this material, or the performance or use of this product. In the interest of continuing product improvement, ViewSonic Corporation reserves the right to change product specications without notice. Information in this document may change without notice. No part of this document may be copied, reproduced, or transmitted by any means,

for any purpose without prior written permission from ViewSonic Corporation.

Product Registration

To fulfill possible future product needs, and to receive additional product information as it becomes available, please visit your region section on ViewSonic’s website to register your product online. The ViewSonic CD also provides an opportunity for you to print the product registration form. Upon completion, please mail or fax to a respective ViewSonic office. To find your registration form, use the directory “:\CD\Registration”. Registering your product will best prepare you for future customer service needs. Please print this user guide and fill the information in the “For Your Records” section. Your LCD displays serial number is located on the rear side of the display. For additional information, please see the “Customer Support” section in this guide.

For Your Records

Product Name: Pro8520HD

ViewSonic DLP Projector

Model Number: VS14804 Document Number: Pro8520HD_UG_ENG Rev. 1B 05-15-13 Serial Number: ________________________________ Purchase Date: ________________________________

Product disposal at end of product life

The lamp in this product contains mercury which can be dangerous to you and the environment. Please use care and dispose of in accordance with local, state or federal laws. ViewSonic respects the environment and is committed to working and living green. Thank you for being part of Smarter, Greener Computing. Please visit ViewSonic website to learn more. USA & Canada: http://www.viewsonic.com/company/green/recycle-program/ Europe: http://www.viewsoniceurope.com/uk/support/recycling-information/ Taiwan: http://recycle.epa.gov.tw/recycle/index2.aspx

Page 6

Notes on the AC Power Cord

For Australia and Mainland China

For the U.S.A. and Canada

For the U.K.

Ground

For Continental Europe

Ground

AC Power Cord must meet the requirement of countries where you use this projector. Please confirm your AC plug type with the graphics below and ensure that the proper AC Power Cord is used. If the supplied AC Power Cord does not match your AC outlet, please contact your sales dealer. This projector is equipped with a grounding type AC line plug. Please ensure that your outlet fits the plug. Do not defeat the safety purpose of this grounding type plug. We highly recommend using a video source device also equipped with a grounding type AC line plug to prevent signal interference due to voltage fluctuations.

Page 7

Table of contents

Introduction ........................................................................................... 1

Projector Features ................................................................................................................................. 1

Package Contents .................................................................................................................................. 2

Projector Overview ................................................................................................................................. 3

Using the Product ................................................................................. 5

Control Panel ......................................................................................................................................... 5

Connection Ports ................................................................................................................................... 6

Remote Control ...................................................................................................................................... 8

Installing the Batteries .......................................................................................................................... 10

Remote Control Operation ................................................................................................................... 11

Connection .......................................................................................... 12

Connecting a computer or monitor ....................................................................................................... 13

Connecting Video source devices ........................................................................................................ 14

Operation ............................................................................................. 17

Powering On/Off the Projector ............................................................................................................. 17

Adjusting the Projector Height ............................................................................................................. 18

Adjusting the Projector Zoom and Focus ............................................................................................. 18

Adjusting Projection Image Size .......................................................................................................... 19

Locking control keys ............................................................................................................................ 20

Menu Operation ................................................................................................................................... 21

Controlling the projector through a LAN environment .......................................................................... 30

Controlling the projector through a web browser ................................................................................. 33

Displaying images through vsPresenter .............................................................................................. 38

Displaying pictures with a USB storage device .................................................................................... 42

Maintenance ........................................................................................ 45

Cleaning the Lens ................................................................................................................................ 45

Cleaning the Projector Housing ........................................................................................................... 45

Cleaning the Filter Cover ..................................................................................................................... 45

Replacing the Lamp ............................................................................................................................. 46

Specifications ..................................................................................... 48

Dimensions .......................................................................................................................................... 49

Ceiling mount installation ..................................................................................................................... 49

Appendix .............................................................................................. 50

LED Indicator Messages ..................................................................................................................... 50

Compatibility Modes ............................................................................................................................. 51

Troubleshooting ................................................................................................................................... 52

RS-232 Command and Configuration .................................................................................................. 53

IR Control Code ................................................................................................................................... 55

Page 8

Introduction

Projector Features

The projector integrates high-performance optical engine projection and a user - friendly design to deliver high reliability and ease of use.

The projector offers the following features:

• Single chip 0.65" Texas Instruments DLP® technology

• 1080p (1920 x 1080 pixels)

• Compatibility with Macintosh® computers

• Compatibility with NTSC, PAL, SECAM and HDTV

• D-Sub 15-pin terminal for analog video connectivity

• User-friendly, multi-language on-screen display

• Advanced electronic keystone correction

• RS-232 connector for serial control

• HDMI compatibility

• PJLinkTM compatible

• LAN Settings allowing management of projector status from a remote computer

• LAN display 4-1 (maximum 4PC/ NB display to 1 projector)

• LAN display 1-M available (1PC/ NB can display to maximum 8 projectors at the same time)

• USB display supports computer connection via USB mini-B type to A type cable

• Support USB flash drive for JPEG presentation

• Less than 0.5 W power consumption in standby mode

Note

• The information in this manual is subject to change without notices.

• The reproduction, transfer or copy of all or any part of this document is not permitted

without express written consent.

Page 9

Package Contents

When you unpack the projector, make sure you have all these components:

HDMI2 Compo

HDMI1

Video

Auto

Enter

Swap

Default

Projector with Lens Cap AC Power Cord Remote Control (IR) & batteries

V ie w S o n ic

VGA Cable (D-SUB to D-

SUB)

Optional accessories

Filter cover RS232 cable RGB to component adapter

Projector Carrying Case

Note

HDMI Cable

ViewSonic

DVD Wizard

Quick Start

Guide

• Contact you dealer immediately if any items are missing, appear damaged, or if the unit

does not work

• For maximum protection of the product, please save the original shipping carton and

packing materials and repack your product as it was originally packed at the factory if you need to ship it.

Page 10

Projector Overview

Front View

12 11 10 9

1. Lens cap 2. Elevator button

3. Elevator foot 4. Lens cap strap

5. Projection lens 6. Front IR remote control sensor

7. Ventilation holes (intake) 8. Filter cover

9. Speaker 10. Focus ring

11. Zoom ring 12. Control panel

13. Lamp cover

Page 11

Rear View

324 6

1. Connection ports 2. AC power socket

3. Kensington lock 4. Rear IR remote control sensor

5. Speaker 6. Ventilation holes (exhaust)

Bottom View

1. Ceiling mount holes (M4*8) 2. Tilt-adjustment feet

3. Security bar

Note

• This projector can be used with a ceiling mount for support. The ceiling mount is not

included in the package.

• Contact your dealer for information to mount the projector on a ceiling.

Page 12

Using the Product

Control Panel

1 3

7 5 4

1. Power (Power LED indicator)

Refer to “LED Indicator Messages”.

2. TEMP (Temperature LED indicator)

Refer to “LED Indicator Messages”.

3. LAMP (Lamp LED indicator)

Refer to “LED Indicator Messages”.

4. Keystone/Arrow keys ( /Up, /Down)

Manually correct distorted images resulting from an angled projection.

5. Four directional buttons

Use four directional buttons to select items or make adjustments to your selection.

6. ENTER

Enter to sub-menu and confirm the menu selection.

7. SOURCE

Display the source selection bar.

8. MENU/EXIT

Display or exit the on-screen display menus.

9. Power

Turn the projector on or off.

10. Right/Panel key

Activate panel key lock.

Page 13

Connection Ports

1. RS-232

When operating the projector via a computer, connect this to the controlling computer's RS-232C port.

2. Monitor Out

Connect to a computer display, etc.

3. Component (Y Cb/Pb Cr/Pr)

Connect Y Cb/Pb Cr/Pr output from video equipment to this jack.

4. S-Video

Connect S-Video output from video equipment to this jack.

1213

5. USB B

USB display supports computer connection via USB mini-B type to A type cable.

6. USB A

This connector supports firmware update, USB flash drive display and wireless dongle for USB display.

7. LAN

For LAN display/network control and web server.

8. HDMI 1

Connect HDMI output from video equipment to this jack.

9. HDMI 2

Connect HDMI output from video equipment to this jack.

10. DC 12V Out

12V DC out

11. MIC in

Microphone input jack.

12. Audio Out

Connect to a speaker or other audio input equipment.

13. Audio 2

Connect an audio output from video equipment or computer to this jack.

14. Audio 1

Connect an audio output from video equipment or computer to this jack.

Page 14

15. Audio 3 (L/R)

Connect an audio output from video equipment to this jack.

16. Video

Connect composite video output from video equipment to this jack.

17. Computer in 2

Connect image input signal (analog RGB or component) to this jack.

18. Computer in 1

Connect image input signal (analog RGB or component) to this jack.

Page 15

Remote Control

1. Power

Turn the projector on or off.

3 4

4 6 7

9 10 11

HDMI1 HDMI2 Compo

Video

Auto

Enter

Swap

Default

19 20 21 22 23 24

2. HDMI 1

Display HDMI 1 signal.

3. Video

Switch input source to Composite/S-Video by sequence.

4. Up/Volume +, Down/Volume - When the On-Screen Display (OSD) menu is not activated, adjust the projector’s sound level.

5. Left/Mute When the On-Screen Display (OSD) menu is not activated, this button is used as mute function.

6. Menu

Display on-screen display menus.

7. User 1

Recall the customized settings based on the current available settings.

8. Source

Display the source selection bar.

9. Gamma

Change the gamma setting.

10. Pattern

Display embedded test pattern.

11. Color Mode

Page 16

Change the image mode setting by sequence.

12. Blank

Cut off the screen temporarily. Press again to cancel the Blank Screen function.

13. Light

Enable backlight functions of the remote control’s buttons.

14. Compo

Display Component video (YPbPr/ YCbCr) signal.

15. HDMI 2

Display HDMI 2 signal.

16. PC

Switch input source to Computer in 1/Computer in 2 by sequence.

17. Auto/Enter

Resynchronize the projector to the input signal from a computer. This function is available for computer mode only.

Confirmed selections.

18. Right/ Lock When the On-Screen Display (OSD) menu is activated, the #4, #5, and #18 keys are used as directional arrows to select the desired menu items and to make adjustments.

Activate panel key lock.

19. ESC

Leave current page or items or to close OSD.

20. User 2

Recall the customized settings based on the current available settings.

21. PIP/POP

Switch screen to PIP/POP by sequence.

22. Swap

Swap input source in PIP or POP image.

23. Aspect

Select the display aspect ratio.

24. RGBCMY

Change indivial RGBCMY color (user color setting).

25. Default

Restore settings to factory default.

Page 17

Installing the Batteries

1. Open the battery cover in the

direction shown.

2. Install batteries as indicated by the

diagram inside the compartment.

3. Close the battery cover into position.

Caution

• Risk of explosion if battery is replaced by an incorrect type.

• Dispose of used batteries according to the instructions.

• Make sure the plus and minus terminals are correctly aligned when loading a battery.

Note

• Keep the batteries out of the reach of children. There is a danger of death by

accidentally swallowing the batteries.

• Remove batteries from remote control when not using for extended periods.

• Do not dispose of the used batteries along with household waste. Dispose of used

batteries according to local regulations.

• Danger of explosion may happen if batteries are incorrectly replaced. Replce all the

batteries with new ones.

• Batteries should not be in or near to fire or water, keep batteries in a dark, cool and dry

place.

• If suspect battery leakage, wipe out the leakage and then replace new batteries. If the

leakage adheres to your body or clothes, rinse well with water immediately.

Page 18

Remote Control Operation

Point the remote control at the infrared remote sensor and press a button.

• Operating the projector from the front

• Operating the projector from the rear

HDMI1

Video

HDMI2 Compo

Auto

Enter

Swap

Default

HDMI1

Video

HDMI2 Compo

Auto

Enter

Swap

Default

Note

• Do not point the laser directly to the people's eyes (especially small children). There is a

danger of injury to the eyes.

• The remote control may not operate when there is sunlight or other strong light such as

a fluorescent lamp shining on the remote sensor.

• Operate the remote control from a position where the remote sensor is visible.

• Do not drop the remote control or jolt it.

• Keep the remote control out of locations with excessively high temperature or humidity.

• Do not get water on the remote control or place wet objects on it.

• Do not disassemble the remote control.

Page 19

Connection

When connecting a signal source to the projector, be sure to:

1. Turn all equipment off before making any connections.

2. Use the correct signal cables for each source.

3. Ensure the cables are firmly inserted.

1. VGA cable (D-Sub to D-Sub) 2. VGA to DVI-A cable

3. USB cable (mini-B type to A type) 4. VGA (D-Sub) to HDTV (RCA) cable

5. Component Video cable 6. Audio L/R cable

7. S-Video cable 8. Composite Video cable

9. Audio cable 10. HDMI cable

11. Microphone 3.5 mini jack cable 12. USB flash drive

Important

• In the connections shown above, some cables may not be included with the projector

(see "Package Contents" on page 2). They are commercially available from electronics stores.

• The connection illustrations above are for reference only. The rear connecting jacks

available on the projector vary with each projector model.

• For detailed connection methods, see pages 13-16.

Page 20

Connecting a computer or monitor

Connecting a computer

The projector provides two VGA input sockets that allow you to connect them to both IBM® compatibles and Macintosh® computers. A Mac adapter is needed if you are connecting legacy version Macintosh computers.

To connect the projector to a notebook or desktop computer:

1. Take the supplied VGA cable and connect one end to the D-Sub output socket of

the computer.

2. Connect the other end of the VGA cable to the Computer in 1 or Computer in 2

signal input socket on the projector.

3. If you wish to use the USB display, take a USB cable and connect the A type end

to the USB port of the computer, and the other end to the USB B socket on the projector.

Important

• Many notebooks do not turn on their external video ports when connected to a

projector. Usually a key combo like FN + F3 or CRT/LCD key turns the external display on/off. Locate a function key labeled CRT/LCD or a function key with a monitor symbol on the notebook. Press FN and the labeled function key simultaneously. Refer to your notebook's documentation to find your notebook's key combination.

Connecting a monitor

If you want to view your presentation close-up on a monitor as well as on the screen, you can connect the Monitor Out signal output socket on the projector to an external monitor with a VGA cable following the instructions below:

To connect the projector to a monitor:

1. Connect the projector to a computer as described in "Connecting a computer" on

page 13.

2. Take a suitable VGA cable (only one supplied) and connect one end of the cable to

the D-Sub input socket of the video monitor.

Or if your monitor is equipped with a DVI input socket, take a VGA to DVI-A cable and connect the DVI end of the cable to the DVI input socket of the video monitor.

3. Connect the other end of the cable to the Monitor Out socket on the projector.

Important

• The Monitor Out output only works when Computer in 1 or Computer in 2 is made to the

projector.

Page 21

Connecting Video source devices

You can connect your projector to various Video source devices that provide any one of the following output sockets:

• Component Video

• S-Video

• Video (composite)

You need only connect the projector to a Video source device using just one of the above connecting methods, however each provides a different level of video quality. The method you choose will most likely depend upon the availability of matching terminals on both the projector and the Video source device as described below:

Best video quality

The best available video connection method is Component Video (not to be confused with composite Video). Digital TV tuner and DVD players output Component Video natively, so if available on your devices, this should be your connection method of choice in preference to (composite) Video.

See "Connecting a Component Video source device" on page 15 for how to connect the projector to a component video device.

Better video quality

The S-Video method provides a better quality analog video than standard composite Video. If you have both composite Video and S-Video output terminals on your Video source device, you should elect to use the S-Video option.

See "Connecting an S-Video source device" on page 15 for how to connect the projector to an S-Video device.

Least video quality

Composite Video is an analog video and will result in a perfectly acceptable, but less than optimal result from your projector, being the least video quality of the available methods described here.

See "Connecting a composite Video source device" on page 16 for how to connect the projector to a composite Video device.

Page 22

Connecting a Component Video source device

Examine your Video source device to determine if it has a set of unused Component Video output sockets available:

• If so, you can continue with this procedure.

• If not, you will need to reassess which method you can use to connect to the device.

To connect the projector to a Component Video source device:

1. Take a VGA (D-Sub) to HDTV (RCA) cable, Component Video cable or a

Component Video to VGA (D-Sub) adaptor and connect the end with 3 RCA type connectors to the Component Video output sockets of the Video source device. Match the color of the plugs to the color of the sockets; green to green, blue to blue, and red to red.

2. If you are using the VGA (D-Sub) to HDTV (RCA) cable and the Component Video

to VGA (D-Sub) adaptor, connect the other end of the cable (with a D-Sub type connector) to the Computer in 1 or Computer in 2 socket on the projector. If you are using the Component Video Cable, connect the other end of 3RCA type connectors to the Y Cb/Pb Cr/Pr sockets on the projector.

Important

• If the selected video image is not displayed after the projector is turned on and the

correct video source has been selected, check that the Video source device is turned on and operating correctly. Also check that the signal cables have been connected correctly.

• RGB to component adapter (ViewSonic P/N: J2552-0212-00)

Connecting an S-Video source device

Examine your Video source device to determine if it has an unused S-Video output socket available:

• If so, you can continue with this procedure.

• If not, you will need to reassess which method you can use to connect to the device.

To connect the projector to an S-Video source device:

1. Take an S-Video cable and connect one end to the S-Video output socket of the

Video source device.

2. Connect the other end of the S-Video cable to the S-Video socket on the projector.

Important

•

If the selected video image is not displayed after the projector is turned on and the correct video source has been selected, check that the Video source device is turned on and operating correctly. Also check that the signal cables have been connected correctly.

• If you have already made a Component Video connection between the projector and this

S-Video source device using Component Video connections, you need not connect to this device using an S-Video connection as this makes an unnecessary second connection of poorer picture quality. See "Connecting Video source devices" on page

14 for details.

Page 23

Connecting a composite Video source device

Examine your Video source device to determine if it has a set of unused composite Video output sockets available:

• If so, you can continue with this procedure.

• If not, you will need to reassess which method you can use to connect to the device.

To connect the projector to a composite Video source device:

1. Take a Video cable and connect one end to the composite Video output socket of

the Video source device.

2. Connect the other end of the Video cable to the Video socket on the projector.

Important

If the selected video image is not displayed after the projector is turned on and the

•

correct video source has been selected, check that the Video source device is turned on and operating correctly. Also check that the signal cables have been connected correctly.

• You need only connect to this device using a composite Video connection if Component

Video and S-Video inputs are unavailable for use. See "Connecting Video source

devices" on page 14 for details.

About the microphone input

• If you wish to use a microphone, connect a 3.5 mini jack cable microphone to the

projector.

• You can use a wireless microphone as long as a wireless module is attached to the

projector's microphone input jack and it works well with the associated devices. To ensure a quality use of the wireless microphone, it is recommended that your microphone conforms to the specifications listed in the table below.

Signal Parameter Min Type Max

Microphone Transducer Principle Dynamic

Impedance 300 1K ohm

Frequency response 600 16K Hz

Page 24

Operation

Powering On/Off the Projector

Powering On the Projector:

1. Remove the projector lens cap.

2. Complete the AC power cord and peripheral signal cable(s) connections.

3. Press to turn on the projector.

The projector takes a minute or so to warm up.

4. Turn on your source (computer, notebook, DVD, etc.). The projector automatically

detects your source.

• If you are connecting multiple sources to the projector simultaneously, press SOURCE on the projector to select your desired signal or press your desired signal key on the remote control.

Warning

• Remove the lens cap first before powering on.

• Never look into the lens when the lamp is on. This can damage your eyes.

• This focal point concentrates high temperature. Do not place any object near it to avoid

possible fire hazard.

Powering Off the Projector:

1. Press to turn off the projector lamp. You will see a message "Power off" appear on the screen.

2. Press again to confirm.

• When the Power LED begins flashing, the projector has entered stand-by mode.

3. Disconnect the AC power cord from the electrical outlet and the projector.

4. Do not turn on the projector right after power off

Page 25

Adjusting the Projector Height

Tilt-adjustment feet

Elevator foot

Elevator button

The projector is equipped with an elevator foot to adjust the image height. To raise or lower the image:

1. To raise or lower the image, press the elevator button and raise or lower the front of the projector. Release the button to lock the adjustment.

2. To level the image on the screen, turn the tilt-adjustment feet to fine-tune the height.

Note

•

To avoid damaging the projector, make sure that the elevator foot and tilt-adjustment feet are fully retracted before placing the projector in its carrying case.

Adjusting the Projector Zoom and Focus

Zoom ring

Focus ring

1. Focus the image by rotating the focus ring. A still image is recommended for focusing.

2. Adjust the image size by sliding the zoom ring.

Page 26

Adjusting Projection Image Size

Refer to the graphic and table below to determine the screen size and projection distance.

Maximum zoom

Screen size

Diagonal

[inch (cm)]

30 (76) 35 (0.89) 55 (1.39) 14.7 (37) 5.0 (12.8) 40 (102) 48 (1.21) 74 (1.87) 19.6 (50) 6.7 (17.1) 50 (127) 60 (1.52) 93 (2.35) 24.5 (62) 8.4 (21.4) 60 (152) 72 (1.83) 111 (2.83) 29.4 (75) 10.1 (25.6) 80 (203) 97 (2.46) 149 (3.79) 39.2 (100) 13.5 (34.2)

100 (254) 122 (3.09) 187 (4.75) 49 (125) 16.8 (42.7) 120 (305) 146 (3.72) 224 (5.7) 58.8 (149) 20.2 (51.3) 150 (381) 183 (4.66) 281 (7.14) 73.5 (187) 25.2 (64.1) 200 (508) 246 (6.24) 376 (9.54) 98.1 (249) 33.6 (85.4) 220 (559) 270 (6.87) 413 (10.5) 107.9 (274) 37.0 (94.0) 250 (635) 307 (7.81) 470 (11.94) 122.6 (311) 42.0 (106.8) 300 (762) 369 (9.38) 564 (14.33) 147.1 (374) 50.5 (128.2)

(min. zoom) (max. zoom)

Minimum zoom

Vertical offset

Projection distance

16 : 9 Screen

Projection distance [inch (m)]

Screen

Center of lens

Image height

[inch (cm)]

Vertical offset

[inch (cm)]

Note

• Position the projector in a horizontal position; other positions can cause heat build-up

and damage to the projector.

• Keep a space of 30 cm or more between the sides of the projector.

• Do not use the projector in a smoky environment. Smoke residue may build-up on

critical parts and damage the projector or its performance

• Consult with your dealer for special installation such as suspending from a ceiling.

There is 3% tolerance among these numbers due to optical component variations. It is recommended that if you intend to permanently install the projector, you should physically test the projection size and distance using the actual projector in situ before you permanently install it, so as to make allowance for this projector's optical characteristics. This will help you determine the exact mounting position so that it best suits your installation location.

Page 27

Locking control keys

With the control keys on the projector locked, you can prevent your projector settings from being changed accidentally (by children, for example). When the Panel Key Lock is on, no control keys on the projector will operate except Power.

1. Press and hold for 3 seconds on the projector or remote control.

HDMI2 Compo

To release panel key lock, press and hold

for 3 seconds on the projector.

Important

• Keys on the remote control are still functional when panel key lock is enabled.

HDMI1

Video

Auto

Enter

Swap

Default

• If you press

Power to turn off the projector without disabling panel key lock, the

projector will still be in locked status the next time it is turned on.

Page 28

Menu Operation

The projector has multilingual on-screen display menus that allow you to make image adjustments and change a variety of settings.

Brightest, Standard, Theater,

Color Mode

Dark Room, DICOM SIM, User1, User2

Video/Audio

Video Setting

Overscan

Noise Reduction

Audio Setting

Microphone Volume

Speaker Volume

Mute

Saturation*4

Sharpness*5

Tint*6

Color Temp.

Red Gain

Green Gain

Blue Gain

Color

Hue

Saturation

Gain

0 - 100

0 - 200

0 - 100

0% - 10%

Off, LOW, MID, HIGH

Computer 1

Computer 2

Video Source

HDMI 1

HDMI 2

0 - 10

0 - 20

User, LOW, MID, HIGH

0 - 100

Red, Green, Blue, Cyan, Megenta, Yellow

0 - 255

Audio 1, Audio 2, Audio 3

Audio 1, Audio 2, Audio 3, HDMI

Page 29

Setting

Auto Keystone

Keystone -40 - +40

Aspect Ratio

Filter Mode*2

High Altitude

Quick Power On

Quick Power Off

DC 12V Trigger

OSD Setting

Others

Function*3

Display Type

Swap

Green Mode

Auto, 4:3, 16:9, ANAMORPHIC 1, ANAMORPHIC 2

Front-Table, Front-Ceiling, Rear-Table, Rear-Ceiling

Input Password

Password Delete

Black, Red, Green, Blue, Cyan, Yellow, Magenta, White

OSD Timeout

OSD Transparency

Off, CC1, CC2, CC3, CC4, T1, T2, T3, T4

Status Message

Zoom

Test Pattern

Off, PIP, POP

DCR

Yes, No

Top-Left, Bottom-Left, Center, Top-Right, Bottom-Right

20 - 60

0, 10, 20, 30, 40, 50, 60, 70, 80, 90

Page 30

NetWork

Wired LAN

Wireless LAN

Status

Default Gateway

DNS

Apply

Status

SSID

Connection Mode

Disconnect, Connect

On, Off

Disconnect, Connect

AP, Infrastructure

Information

Network Restart

Input Source

MAC Address

Filter Hours*2

Filter Hours Reset*2

Equivalent Lamp Hours

Equivalent Lamp Hours Reset

Factory Default

Yes, No

*1 Adjustable range and default setting vary depending on signal type. *2 This function is only available when the projector is installed an optional filter cover. *3 The selectable Function list includes Color Mode, Gamma, Overscan, Noise

Reduction, Keystone and Filter Mode. *4 Saturation is supported under Component, Video and S-Video modes. *5 Sharpness is supported under HDMI, Component, Video and S-Video modes. *6 Tint is supported under Component, Video and S-Video modes.

Page 31

How to operate

1. Press

2. When OSD is displayed, use

3. After selecting the desired main menu item, press

4. Use

5. Press

on the projector or

on the remote control to open the OSD menu.

to select any feature in the main menu.

to select the desired item and adjust the settings with

on the projector or

on the remote control, the screen will return to

to select feature setting.

the main menu.

6. To exit OSD, press

on the projector or

on the remote control again. The

OSD menu will close and the projector will automatically save the new settings.

Picture

Color Mode

There are many factory presets optimized for various types of images.

• Brightest:For the brightest environment.

• Standard:For computer or notebook.

• Theater :For home theater.

• Dark Room:For dark environment.

• DICOM SIM: Recommended for DICOM format files in simulation mode.

• User 1:Memorize user 1 defined settings.

• User 2:Memorize user 2 defined settings.

Note

•

DCIM SIM option is only for training or reference. It not used for actual diagnosis.

• DICOM represents for the Digital Imaging and Communications in Medicine. This is a

standard created by the American College of Radiology and the National Electrical Manufacturers Association. This standard specifies the method of digital image data to be transferred from one system to another.

Brightness

Brighten or darken the image.

Contrast

Set the difference between light and dark areas.

Video Setting

Allow you to enter the Video Setting menu.

• Saturation: Adjust a video image from black and white to fully saturated color.

• Sharpness: Sharpen or soften the image.

•Tint: Shift colors toward red or green.

Color Setting

Adjust the color temperature. At higher temperature the screen looks colder; at lower temperature, the screen looks warmer. If you select “User”, then you can change the intensity of each of 3 color (Red, Green, Blue) to customize user color temperature.

User Color

Page 32

User Color provides six sets (RGBCMY) of colors to be adjusted. When you select each color, you can independently adjust its range and saturation according to your preference.

Gamma

Effect the represent of dark scenery. With greater gamma value, dark scenery will look brighter.

Video/Audio

Frequency

Adjust the timing of the projector relative to the computer.

Tracking

Adjust the phase of the projector relative to the computer.

H Position (Horizontal Position)

Adjust the image left or right within the projection area.

V Position (Vertical Position)

Adjust the image up or down within the projection area.

Overscan

Remove noise around the video image.

Noise Reduction

Reduce temporal and/or spatial noise in the image.

Audio Setting

Allow you to enter the Audio Setting menu.

• Computer 1:

•

When Audio in 1 is turned on, Audio in 2 and Audio in 3 will turn off automatically.

• Computer 2:

•

When Audio in 2 is turned on, Audio in 1 and Audio in 3 will turn off automatically.

• Video Source:

•

When Audio in 3 is turned on, Audio in 1 and Audio in 2 will turn off automatically.

Select the audio input for Computer in 1 signal.

Select the audio input for Computer in 2 signal.

Select the audio input for video source.

• HDMI 1: Select the audio input for HDMI 1 signal.

• When HDMI 1 is turned on, Audio in 1, Audio in 2 and Audio in 3 will turn off

automatically.

• HDMI 2: Select the audio input for HDMI 2 signal.

• When HDMI 2 is turned on, Audio in 1, Audio in 2 and Audio in 3 will turn off

automatically.

Microphone Volume

Adjust the microphone’s volume level.

Speaker Volume

Adjust the projector’s volume level.

Mute

Cut off the sound temporarily.

Setting

Page 33

Auto Keystone

Automatically correct distorted images resulting from an angled projection.

Keystone

Manually correct distorted images resulting from an angled projection.

• When adjusting the Keystone, Auto Keystone will be set at "Off" automatically.

Aspect Ratio

Select how the picture fits on the screen:

• Auto:Scales an image proportionally to fit the projector's native resolution in its

horizontal or vertical width.

• 4:3:Scales an image so that it is displayed in the center of the screen with a 4:3

aspect ratio.

• 16:9:Scales an image so that it is displayed in the center of the screen with a 16:9

aspect ratio.

• ANAMORPHIC 1: Scale an image so that it is displayed in the center of the screen

with a 1.85:1 aspect ratio.

• ANAMORPHIC 2: Scale an image so that it is displayed in the center of the screen

with a 2.35:1 aspect ratio.

Projection

Adjust the picture to match the orientation of the projector: upright or upside-down, in front of or behind the screen. Invert or reverse the image accordingly.

Power Saving

If the input source is not detected and no operation is performed for a specific period of time, projector will automatically turn off.

Auto Source

Automatically scan through all the input source.

Signal Type

Specify the source to the Computer in 1/Computer in 2 terminal that you wish to project.

Auto: Automatically detect the input signal type from Computer in 1 and Computer in 2

• terminals.

•

RGB: For VGA signal

•

YCbCr:For component signal

ECO Mode

Use this function to dim the projector lamp light output which will lower power consumption and increase lamp life.

•

This function will be unavailable when the DCR function is on.

Filter Mode

Use this function to activate filter mode after the projector is installed an optional filter cover.

High Altitude

Use this function to allow the fans operates at full speed continuously to achieve proper high altitude cooling of the projector.

Quick Power On

Page 34

•

On: The projector will turn on in 3 seconds.

•

Off: The projector will turn on following normal power on procedure.

Quick Power Off

•

On: The projector will directly shut down without cooling procedure.

•

Off: The projector will shut down following normal cooling procedure.

DC 12V Trigger

1. When Green Mode is off and the projector is under standby mode, you can enable

or disable to trigger external devices such as anelectric screen.

2. When Green Mode is on and the projector is under standby mode, DC 12V will not

trigger the screen no matter you set to on or off.

3. When the projector is under normal projection, DC 12V will always trigger the

screen no matter you set to on or off.

Option

Password

Set or delete the password. When the password function is added, image projection will require to input the preset password when turning on the projector.

Blank Screen

Blank the screen temporarily, and select the screen color when this function is active.

OSD Setting

Allow you to enter the OSD Setting menu.

• Menu Position: Choose the menu location on the display screen.

• OSD Timeout: Duration of OSD menu display countly starts (at idle state by second).

• OSD Transparency: Select to change the transparency level of the OSD background.

Closed Caption

Enable or disable closed captions by selecting CC1 (closed caption1, the most common channel), CC2, CC3, CC4, T1, T2,T3, T4 or OFF.

Others

Allow you to enter the Others menu.

• Message: Enable or disable the message box at the right bottom of the screen.

• Zoom: Zoom in and out the images.

• DCR (Dynamic Contrast Ratio): Enable DCR will further enhance contrast ratio by darkening the black scenes. Disable DCR will resume to normal contrast performance. DCR will impact lamp life and system noise performance.

• Test Pattern: Display embedded test pattern.

Function

Allow user to define a short cut key on the remote control, and the function item is selected in OSD menu.

Display Type

Allow user to select PIP (Picture in Picture) screen, POP (Picture on Picture) screen or disable PIP/POP function.

Page 35

Swap

Allow user to swap input source in PIP or POP image.

Green Mode

Enable this function when power consumption is under 0.5W.

Network

Wired LAN

Allow you to configure the wired LAN settings.

• Status: Display the projector’s status.

• DHCP: Abbreviation for Dynamic Host Configuration Protocol. This protocol

automatically assigns IP Address to networked devices.

• When the “DHCP” sets to “On”, it takes some time to obtain IP address from

DHCP server.

• When the "DHCP" sets to "Off", that means user will set IP address by manually.

• IP Address: Numerical address to identify networked computers. This function can

only be used when DHCP is set to Off.

• The IP Address is the number that identifies this projector on the network. You

cannot have two devices with the same IP Address on the same network.

• The IP Address “0.0.0.0” is prohibited.

• Subnet Mask: A numeric value to define the number of bits used for a network

address of a divided network (or subnet) in an IP Address. This function can only be used when DHCP is set to Off.

• The Subnet Mask “0.0.0.0” is prohibited.

• Default Gateway: A server (or router) to communicate across networks (subnets)

that are divided by Subnet Mask. This function can only be used when DHCP is set to Off.

• DNS: Setup DNS server address when DHCP is disable.

• Apply: Save and execute the wired LAN settings.

Wirless LAN

Allow you to configure the wireless LAN settings.

• Status: Display the projector’s status.

• SSID: Display the projector’s SSID information.

• IP Address: Numerical address to identify networked computers. This function can

only be used when DHCP is set to Off.

• The IP Address is the number that identifies this projector on the network. You

cannot have two devices with the same IP Address on the same network.

• The IP Address “0.0.0.0” is prohibited.

• Connection Mode: Methods for connecting to wireless networks with Wi-Fi enabled

devices.

Network Restart

Restore network settings to default. The password for web administrator and vsPresenter will be reset to default “admin”.

Information

Page 36

Input Source

Display the current input source.

Resolution

Display current input source resolution.

H. Frequency

Display current image horizontal frequency.

V. Frequency

Display current image vertical frequency.

MAC Address

Abbreviation for Media Access Control Address. MAC Address is a unique ID number assigned to each network adapter.

Filter Hours

Display the filter’s elapsed operating time (in hours).

•

When Filter Mode is turned on, the Filter Hours also turns on automatically.

Filter Hours Reset

Reset the filter Hour to 0 hours.

Equivalent Lamp Hours

Display the lamp’s elapsed operating time (in hours).

Equivalent Lamp Hours Reset

Reset the lamp Hour to 0 hours.

Factory Default

Restore settings to factory default. The following settings will still remain: MAC Address, Language, Projection, High

Altitude, Filter Mode, Password, Lamp Hours, Filter Hours, Auto Keystone, Keystone.

Language

Select the language used by the on-screen menu.

Page 37

Controlling the projector through a LAN environment

You can manage and control the projector from one or more remote computers when they are properly connected to the same local area network.

Wired connection

Internet

IP Router

If you are in a DHCP environment:

1. Take a RJ45 cable and connect one end to the RJ45 LAN input jack of the projector and the other end to the RJ45 port on your Ethernet or router.

2. Press MENU/EXIT on the projector or Menu on the remote control and then press

/ until the Network menu is highlighted.

3. Highlight Wired LAN and press ENTER on the projector or Enter on the remote control.

4. Make sure the Status is Connect.

5. Press

to highlight DHCP and press / to select On.

6. Press to highlight Apply and press ENTER on the projector or Enter on the remote control.

7. Please wait for around 15 - 20 seconds, and then re-enter the Wired LAN page. The IP Address, Subnet Mask, Default Gateway, and DNS settings will be displayed. Note down the IP address displayed in the IP Address row.

Important

• If the Projector IP Address still does not appear, contact your network administrator.

• If the RJ45 cables are not properly connected, the IP Address, Subnet Mask, Default

Gateway, and DNS settings will display 0.0.0.0. Make sure the cables are properly connected and perform the procedures above again.

• If you wish to connect to the projector in its standby mode, be sure you have selected

RJ45 and obtained the IP Address, Subnet Mask, Default Gateway, and DNS information when the projector is on.

If you are in a non-DHCP environment:

1. Repeat steps 1-4 above.

2. Press to highlight DHCP and press / to select Off.

3. Contact your ITS administrator for information on the IP Address, Subnet Mask, Default Gateway, and DNS settings.

4. Press to select the item you want to modify and press ENTER on the projector or Enter on the remote control.

Page 38

5. Press / to move the cursor and the enter the value.

6. To save the settings, press ENTER on the projector or Enter on the remote control. If you do not want to save the settings, press MENU/EXIT on the projector or Menu on the remote control.

7. Press to highlight Apply and press ENTER on the projector or Enter on the remote control.

Important

• If the RJ45 cables are not properly connected, the IP Address, Subnet Mask, Default

Gateway, and DNS settings will display 0.0.0.0. Make sure the cables are properly connected and perform the procedures above again.

• If you wish to connect to the projector in its standby mode, be sure you have selected

RJ45 and obtained the IP Address, Subnet Mask, Default Gateway, and DNS information when the projector is on.

Page 39

Wireless connection

ViewSonic wireless dongle

To connect to the projector wirelessly, you have to plug a ViewSonic wireless dongle (optional) to the USB Type A connector on the projector, and then only a few OSD configuration steps are required.

1. Make sure the projector is turned on.

2. Press MENU/EXIT on the projector or Menu on the remote control and then press

/ until the Network menu is highlighted.

3. Highlight Wireless LAN and press ENTER on the projector or Enter on the remote control.

4. Make sure the Status is Connect.

5. Make sure the SSID information is displayed.

6. In AP mode, you need to use your computer’s wireless connection utility to search the projector’s SSID and connect to it. Then you can search the projector with vsPresenter. To use Infrastructure mode, you should connect both your computer and projector to the same AP router and make connections with the IP address.

About AP and Infrastructure modes

In AP mode, you need to use your computer's wireless connection utility to search for the projector's SSID and connect to it. Then you can search for the projector with vsPresenter.

In Infrastructure mode, you should connect both your computer and projector to the same AP router and make connections with the IP address.

The following diagram describes how to access the Internet in AP and Infrastructure modes.

(AP mode)

Internet

(Infrastructure mode)

Internet

Important

• If you need more information about AP and Infrastructure modes, please refer to user

documentations for Wireless Routers which are usually available on 3C stores.

Page 40

Controlling the projector through a web browser

Once you have the correct IP address for the projector and the projector is on or in standby mode, you can use any computer that is on the same local area network to control the projector.

Important

• If you are using Microsoft Internet Explorer, make sure it is version 7.0 or higher.

• The screenshots in this manual are for reference only, and may differ from the actual

design.

1. Enter the address of the projector in the address bar of your browser and press Enter.

2. The main page of the ViewSonic webpage control system appears.

3. To change the language for the web pages, click the down arrow to reveal a drop down list and select a desired language.

4. To download vsPresenter, click Download. See "Displaying images through

vsPresenter" on page 38 for details.

5. The Crestron (eControl) page displays the Crestron eControl user interface. See

"About Crestron control" on page 34 for details.

6. To have access to the Admin page, you need to enter a password. The default password is “admin”.

Page 41

• System Status: Displays the system information.

• General Setup: Allows you to turn on/off the projector, switch the input signal for

the projector, and change the password for the Administrator page.

• Picture Setup/Image Setup: Provides some OSD menu items for adjusting the

projected pictures. See "Menu Operation" on page 21 for details.

• Alert Setup/Mail Setup: Allows you to setup the mail server and send system

error messages to your ITS administrator.

• Network Setup: Provides wired and wireless network settings.

• Reset to Default: Allows you to restore the device to the factory default settings.

About Crestron control

The Crestron (eControl) page displays the Crestron eControl user interface. The eControl page provides a variety of virtual keys to control the projector or adjust the projected pictures.

You can press

W/X to reveal

more buttons.

iii

i. These buttons function the same as the ones on the OSD menus or remote

control. ii. To switch between input signals, click on your desired signal. iii. To change the language for the Crestron page, click the down arrow to reveal a

drop down list and select a desired language.

Important

• The Menu button can also be used to go back to previous OSD menus, exit and save

menu settings.

• The source list varies according to the connectors available on the projector.

• When you use the projector control panel or remote control to change the OSD menu

settings, it may take a while for the web browser to synchronize these changes with the projector.

Page 42

The tools page allows you to manage the projector, configure the LAN control settings and secure access of remote network operation on this projector.

vii

viii

iv. This section is only used with the Crestron Control System. Please contact

Creston or refer to its user manual for setup information. v. Click the down arrow to reveal a drop down list and select a default language. vi. You can name the projector, keep track of its location and the person in charge

of it. vii. You can adjust the LAN Control Settings. viii.Once set, access to the remote network operation on this projector has been

password-protected. ix. Once set, access to the tools page has been password-protected.

Important

To prevent errors, only input the English alphabet and digits on the tools page.

•

• After making the adjustments, press the Send button and the data will be saved for the

projector.

x. Press Exit to go back to the remote network operation page.

Page 43

Please pay attention to the limitation of input length (including space and other punctuation keys) in the list blow:

Category Item Input Length Maximum Number of

Characters

Crestron Control IP Address 15

IP ID 2

Port 5

Projector Projector Name 10

Location 9

Assigned To 9

Network Configuration DHCP (Enabled) (N/A)

IP Address 15

Subnet Mask 15

Default Gateway 15

DNS Server 15

User Password Enabled (N/A)

New Password 20

Confirm 2

Admin Password Enabled (N/A)

New Password 20

Confirm 20

The info page displays the information and status of this projector.

Press Exit to go back to the remote network operation page.

After pressing the button “Help”, the Help Desk window will appear in the upper right corner of the screen. You will be able to deliver messages to RoomView software administrators/users who connect to the same local area network.

Page 44

Important

• Please only deliver the messages in English letters and digits.

For more information, visit http://www.crestron.com & www.crestron.com/getroomview.

**Crestron RoomView

On the "Edit Room" page, enter the IP Address (or hostname) as shown on the projector's on-screen display (OSD) menu, and "05" for IPID, "41794" for the reserved Crestron control port.

About Crestron RoomView setting and command method, please access below website to get RoomView User Guide and more information:

http://www.crestron.com/features/ roomview_connected_embedded_projectors_devices/resources.asp

Page 45

Displaying images through vsPresenter

Downloading and installing vsPresenter

The vsPresenter is an application running on the host PC. It helps connect your computer to an available network projector and transfer the desktop content to the network projector via local network connection.

1. Enter the main page of Network Control. See steps 1-2 on page 33 for details.

2. Download vsPresenter.

3. When the download is complete, install the software to your computer by clicking the exe file. Follow the on-screen instructions to complete the installation.

4. Launch vsPresenter.

Using vsPresenter

1. The Search page allows you to search and connect to a projector.

i. To connect to a projector, select Directly then type the projector IP address and

click Connect.

ii. To search for projectors, simply click Search to list all the projectors on the

same local area network. Click the desired projectors in the Search result list, and click Connect directly. You can also type a desired projector name and click Search.

iii. You can link to the ViewSonic webpage control system on page 33.

• If you are the first time user, choose your identity as a Normal user or

Administrator. Both require no password. But if you choose to be an Administrator, you have the authority to set a password for connecting to the projector. That password should be kept and used next when you try to connect to the same projector.

• If there are multiple computers connected to the projector, you can decide a

display zone by clicking 1, 2, 3, 4, L, R, All, or Background.

Page 46

2. If you want to freeze the projected image on the screen, press . Any further movements will be not been seen on the screen until is pressed.

3. You can choose a capture mode from here.

i. To display a full screen, click FullScreen. ii. To display a partial screen, click FixedSize. A square appears on your screen.

You can place it where you want to project.

iii. If you wish to change the square, click Alterable.

4. The Basic Setting page allows you to configure vsPresenter.

i. To change the vsPresenter interface language, click the down arrow to reveal a

drop-down list and select a desired language. Click Apply.

ii. Users can change the size parameters of the frame in FixedSize capture mode

by modifying width and height on this page and click Apply to make changes take effect.

iii. User can use the mirror driver for presenter capture image, if the system has

installed the mirror driver. iv. To allow notification messages to appear, click Yes. Click Apply. v. The Software Information is available on this page.

Page 47

5. The Advanced Setting page allows you to configure vsPresenter.

i. To adjust the image quality, click the down arrow to reveal a drop-down list and

select a desired quality level. The higher image quality you select, the higher

network transfer speed is required. Select a YUV sample format between

YUV444 and YUV420. Compared to format YUV420, format YUV 444 provides

better effect but may slow the transport and playing speed. Click Apply after

your selections. ii. To adjust the capture rate, move the slide bar. The network bandwidth may also

affect the performance. iii. Network port setting for fixed or manual type.

6. You can manage the connected projectors listed under Device Management.

• Under a conference mode:

1. Only the administrator can take control.

2. A projector can display up to 4 computer screens.

• You can set the name of your computer under vsPresenter Management.

Page 48

• For details about the icons, please see the following:

Icon Description Icon Description

You are a normal user and

Disconnects from the projector. have no access to change the password.

You are an administrator and have authority to change the

Opens the web page of the

Network Control. password.

You are the user of the projector.

You are an administrator of the projector.

There is another user of the

projector.

You are a normal user of the

projector.

Sets a display zone for the projector.

7. Disconnect

To disconnect from the projector(s), click the Disconnect icon.

Important

• Be sure to turn off other virtual network control programs before using vsPresenter.

Page 49

Displaying pictures with a USB storage device

The projector is built-in an application which can display packaged images on a USB storage device. It can eliminate the need for a computer source.

The projector supports the following image formats:

File format Maximum pixel size

JPEG 8000 x 8000

GIF/TIFF/PNG/BMP 1280 x 800

• Progressive JPEG files are not supported.

• Some JPEG files may not be displayed clearly. To display the images on a USB storage device:

1. Plug the USB storage device into the USB A socket.

2. The projector automatically displays the main screen. Or your can manually select USB A from the source selection bar.

3. Press ENTER on the projector or Enter on the remote control to display the content of your USB storage device.

4. Folders and supported files are represented in thumbnail mode.

• To scroll through the thumbnails, use the four directional arrow keys.

• To open a folder/file, press ENTER or Enter.

• To go back to the previous screen, select the thumbnail with an up arrow in the

top right corner of the screen, and press ENTER or Enter.

• To obtain more functions, press MENU to open the menu. To leave the menu,

press ENTER or Enter again.

When viewing thumbnails

• Next: Selects the next folder/image.

• Previous: Selects the previous folder/image.

• Thumbnail/Full Screen/SlideShow: Displays the selected image in thumbnail/

Full Screen/SlideShow mode.

Page 50

• NameOrder/ExtendOrder/SizeOrder/TimeOrder: Sets the images to be

displayed in the order of filenames, filename extension, file sizes, or time the photos were taken.

• EXIF OFF/EXIF ON: Sets whether to display the image in EXIF format.

• FileName ON/FileName OFF: Sets whether to display the filename.

When viewing slide shows

• Stop: Stops the slide show.

• NEXT: Selects the next image.

• Previous: Selects the previous image.

• Delay 3/Deplay 4/Deplay 5: Sets the interval between the two images display.

• Slide Right/Slide Up/Right Down/XLines/YLines/Blocks: Sets the way the slide

show is displayed.

• Repeat On/Off: Sets whether to repeat the slide shows.

When viewing full screen images

• Thumbnail/Full Screen/SlideShow: Displays the selected image in thumbnail/

Full Screen/SlideShow mode.

• Best Fit/Actual Size: Sets the display size of the image.

• EXIFDisp OFF/EXIFDisp ON: Sets whether to display the EXIF data.

• + 90deg: Rotates the image 90 degrees clockwise.

• -90deg: Rotates the image 90 degrees counterclockwise.

• USB 2.0 compliant USB storage media (Mass Storage Class) is supported.

Page 51

• It is strongly recommended to use an AC power adaptor with the USB hard disk.

• The following formats are recommended for the USB hard disk: FAT12/FAT16/

FAT32 (NTFS format is not supported).

• Some USB flash drives may not work correctly with the projector.

• The security USB flash drive is not supported.

• Do not connect any apparatus other than USB storage devices and other

equipment for battery charge through USB. It may caused malfunction.

• The projector plays up to 200 files in a folder.

• The filenames are displayed in the following order: symbols, digits, letters.

• The projector can display the filenames up to 16 characters including the file

extension.

• The application is best to display the filenames in English. If the files are named in

other languages, the filenames may not show properly, but the content still can be displayed.

• Folders in the USB storage device can be recognized up to 3 layers. The priority of

thumbnail display for image files is as follows:

: Currect directory: A

: Folder B

: Folder D

: Folder E

File display priority in folder: A > B > C > D > E > F. Folder G: Cannot be displayed because it is in the 4th layer.

: Folder G

: Folder C

: Folder F

• Response time may vary depending on image contents when switching pages,

loading and playing files.

Page 52

Maintenance

The projector needs proper maintenance. You should keep the lens clean as dust, dirt or spots will project on the screen and diminish image quality. If any other parts need replacing, contact your dealer or qualified service personnel. When cleaning any part of the projector, always switch off and unplug the projector first.

Warning

• Never open any of the covers on the projector. Dangerous electrical voltages inside the

projector can cause severe injury. Do not attempt to service this product yourself. Refer all servicing to qualified service personnel.

Cleaning the Lens

Gently wipe the lens with lens cleaning paper. Do not touch the lens with your hands.

Cleaning the Projector Housing

Gently wipe with a soft cloth. If dirt and stains are not easily removed, use a soft cloth damped with water, or water and neutral detergent, and wipe dry with a soft, dry cloth.

Cleaning the Filter Cover

The filter cover, which is located at the side of the projector, should be cleaned after every 100 hours of use. If it is not cleaned periodically, it can become clogged with dust and prevent the projector from being ventilated properly. This can cause over heating and damage the projector.

To clean the filter cover:

1. Switch the projector off and unplug the AC power cord from the wall socket.

2. Remove the filter cover as the illustration shown.

3. Clean the filter cover.

• To clean the filter cover, you are advised

to use a small vacuum cleaner designed for computers and other office equipment.

• If the filter cover is torn, replace it.

4. Replace the filter cover.

5. Attach the filter cover.

6. Plug the power back into the projector.

Note

• Turn off the projector and remove the AC power cord from the power outlet before

beginning maintenance work.

• Make sure the lens is cool before cleaning.

• Do not use detergents or chemicals other than those noted above. Do not use benzene

or thinners.

• Do not use chemical sprays.

Page 53

• Use a soft cloth or lens paper only.

Replacing the Lamp

As the projector operates over time, the brightness of the projector lamp gradually decreases and the lamp becomes more susceptible to breakage. We recommend replacing the lamp if a warning message is displayed. Do not attempt to replace the lamp yourself. Contact the qualified service personnel for replacement.

Type number: RLC-076

Note

• The lamp is extremely hot right after turning off the projector. If you touch the lamp, you

may scald your finger. When you replace the lamp, wait for at least 45 minutes for the lamp to cool down.

• Do not touch the lamp glass at any time. The lamp may explode due to improper

handling, including the touching of the lamp glass.

• Lamp lifetime may differ from lamp to lamp and according to the environment of use.

There is no guarantee of the same lifetime for each lamp. Some lamps may fail or terminate their lifetime in a shorter period of time than other similar lamps.

• A lamp may explode as a result of vibration, shock or degradation as a result of hours of

use as its lifetime draws to an end. Risk of explosion may differ according to the environment or conditions in which the projector and lamp are being used.

• Wear protective gloves and eyeglasses when fixing or detaching the lamp.

• Faster on-off-cycles will damage the lamp and reduce lamp life. Wait at least for 5

minutes to turn off the projector after powering on.

• Do not operate the lamp in proximity to paper, cloth, or other combustible material nor

cover it with such materials.

• Do not operate the lamp in an atmosphere containing an inflammable substance, such

as thinner.

• Thoroughly ventilate the area or the room when operating the lamp in an oxygen

atmosphere (in the air). If ozone is inhaled, it could cause headaches, nausea, dizziness, and other symptoms.

• The inorganic mercury is involved in the lamp. If the lamp bursts, the mercury inside the

lamp will be exposed. Leave the area immediately if the lamp shatters while being operated and ventilate the area for at least 30 minutes in order to avoid the inhalation of mercury fumes. Otherwise it could be harmful to user’s health.

Page 54

1. Turn off the projector.

2. If the projector is installed in a ceiling mount, remove it

3. Unplug the power cord.

4. Loosen the screw in the side of the lamp cover and remove the cover.

5. Remove the screws from the lamp module, raise the handle, and lift out the module.

6. Insert the new lamp module into the projector and tighten the screws.

7. Replace the lamp cover and tighten the screw.

8. Turn on the projector. If the lamp does not turn on after the warm-up period, try reinstalling the lamp.

9. Reset the lamp hour. Refer to the “Information” menu.

Note

Dispose the used lamp according to local regulations.

•

• Ensure that screws are tightened properly. Screws not tightened fully may result in

injury or accidents.

• Since the lamp is made of glass, do not drop the unit and do not scratch the glass.

• Do not reuse the old lamp. This could cause the lamp to explode.

• Be sure to turn off the projector and unplug the AC power cord before replacing the

lamp.

• Do not use the projector with the lamp cover removed.

Page 55

Specifications

Display system Single 0.65" DLP panel Resolution 1080p (1920 × 1080 pixels) Zoom 1.5X F/No. 2.41 - 2.97 Focal length 20.72 - 31mm Screen size 30” - 300” Lamp 350W Input terminal D-Sub 15-pin x 2, S-Video x 1, Video x 1, Audio signal input

(3.5 mm stereo mini jack) x 2, HDMI x 2, Component RCA jack x 1, RCA audio jack (L/R) x 1, 3.5 mm Mic input x1, USB A type x1 (supports firmware update, USB flash drive display and wireless dongle for USB display), USB mini-B type x1 (supports USB display)

Output terminal D-Sub 15 pin x 1, Audio signal output (3.5 mm stereo mini

jack) x 1 Control terminal RS-232 x 1, 12-Vdc trigger output x 1, RJ45 x 1 Speaker 10 watt x 2 Video compatibility NTSC, NTSC 4.43

PAL, PA L-N, PA L M

SECAM, HDTV (480i/p, 576p, 720p, 1080i/p), Composite

video Scanning frequency

Horizontal frequency Vertical frequency Environment Operating:

Power requirement AC 100-240 V, 50 - 60 Hz, 4.3A Power consumption 450 W Dimension (W x D x H) 335 x 267 x 132 mm Weight 3.86 kg (8.5 lbs) Note: Design and Specifications are subject to change without prior notice.

31 - 100 KHz

50 - 85 Hz

Temperature: 0°C to 40°C

Humidity: 10%-80%

Storage:

Temperature: -20°C to 60°C

Humidity: 5%-85%

Page 56

Dimensions

335 mm (W) x 267 mm (D) x 132 mm (H)

267

Ceiling mount installation

335

64.5

132

84.9

174

227

Ceiling mount screws: M4 x 8 (Max. L = 8 mm)

Unit: mm

103

Page 57

Appendix

LED Indicator Messages

LED type Color Status Meaning

Power LED Blue Solid Lamp LED Red Off Tem p L E D R e d Of f Power LED Blue Flash Lamp LED Red Off Tem p L E D R e d Of f Power LED Blue Solid

Tem p L E D R e d Of f Power LED Blue Solid

Tem p L E D R e d Of f Power LED Blue Flash Lamp LED Red Off Tem p L E D R e d Of f Power LED Blue Solid Lamp LED Red Solid Temp LED Red Flash Power LED Blue Solid The lamp has reached its end of life and must Lamp LED Red Solid

Tem p L E D R e d Of f

Power LED Blue Solid Lamp LED Red Flash Tem p L E D R e d Of f Power LED Blue Off Lamp LED Red Solid Temp LED Red Solid Power LED Blue Flash Lamp LED Red Off Tem p L E D R e d Of f

Standby mode when green mode is turned on.

Standby mode when green mode is turned off.

Powering upLamp LED Red Off

Normal operationLamp LED Red Off

Powering down (The projector needs to cool for 35 seconds after the power is turned off.)

The projector system has some problems with its fans, so the projector cannot start up.

be changed soon. The lamp will continue to opearate until it failes. Change the lamp. If the lamp is off, then the ballast will become malfuction.

Temperature is too high. The lamp will turn off. The fan motor is cooling the lamp.

The lamp ignition failied. If temperature is too high, the fans will cool the lamp.

The projector needs to cool for 90 seconds after the power is turned off. If you try to restart the projector, it will shut down again.

Page 58

Compatibility Modes

Computer:

Compatibility Resolution H-Sync [KHz] V-Sync [Hz]

24.69 50

31.5 60

VGA 640 x 480

SVGA 800 x 600

XGA 1024 x 768

SXGA 1280 x 1024

UXGA 1600 x 1200 47.7 60 Mac 13 640 x 480 35 67 Mac 16 832 x 624 49.72 75 Mac 19 1024 x 768 60.24 75

1080i30 1920 x 1080 33.75 60 1080i25 1920 x 1080 28.13 50

480p 720 x 480 31.47 59.94

576p 720 x 576 31.25 50 720p60 1280 x 720 45 60 720p50 1280 x 720 37.5 50

1080p60 1920 x 1080 67.5 60 1080p50 1920 x 1080 56.25 50

37.9 72

37.5 75

43.3 85

30.99 50

35.2 56

37.9 60

48.1 72

46.9 75

53.7 85

39.63 50

48.4 60

56.5 70 60 75 64 60 80 75

Video:

Compatibility Resolution H-Sync [KHz] V-Sync [Hz]

1080p 1920 x 1080 67.5 60 1080p 1920 x 1080 56.3 50

1080i 1920 x 1080 33.8 60 1080i 1920 x 1080 28.1 50 720p 1280 x 720 45 60 720p 1280 x 720 37.5 50 576p 720 x 576 31.3 50

576i 720 x 576 15.6 50

480p 720 x 480 31.5 60

480i 720 x 480 15.8 60

Page 59

Troubleshooting

Refer to the symptoms and measures listed below before sending the projector for repairs. If the problem persists, contact your local reseller or service center. Please refer to "LED Indicator Messages" as well.

Start-up problems

If no lights turn on:

•

Be sure that the power cord is securely connected to the projector and the other end

plugged into an outlet with power.

• Press the power button again.

•

Unplug the power cord and wait for a short while, then plug it in and press the power

button again.

Image problems

If the searching source is displayed:

• Press SOURCE on the projector or Source on the remote control to select an active input source.

• Be sure the external source is turned on and connected.

•

For a computer connection, ensure your notebook computer’s external video port is

turned on. Refer to the computer manual.

If the image is out of focus:

• Be sure the lens cover is removed.

•

While displaying the on-screen menu, adjust the focus ring. (The image size should

not change; if it does, you are adjusting the zoom, not the focus.)

• Check the projection lens to see if it needs cleaning.

If the image is flickering or unstable for a computer connection:

•

Press

• Press adjust Frequency or Tracking.

Auto on the remote control.

on the projector or

on the remote control

, go to Video/Audio and

Remote control problems

If the remote control does not operate:

• Be sure nothing is blocking the remote control receiver on the front of the projector. Use the remote control within the effective range.

• Aim the remote control at the screen or at the front or back of the projector.

•

Move the remote control so it is more directly in front of or behind the projector and

not as far to the side.

Page 60

RS-232 Command and Configuration

D-Sub 9 pin

11 CD 2RXD 3TXD 4DTR 5GND 6DSR 7RTS 8CTS 9RI

Baud Rate 19200 bps

Data Length 8 bit

Parity Check None

Stop Bit 1 bit

Flow Control None

Wire List

SHELL DW SHELL

C1 COLOR C2

1 Black 1 2Brown 3 3Red 2 4 Orange 6 5 Yellow 5 6Green 4 7Blue 8 8Purple 7 9White 9

POWER ON / POWER OFF

POWER ON BE,EF,10,05,00,C6,FF,11,11,01,00,01,00

POWER OFF BE,EF,02,06,00,6D,D2,34,00,00,00,00,00

SOURCE SELECT

Computer 1 BE,EF,02,06,00,BC,D3,35,00,00,00,00,00

Computer 2 BE,EF,02,06,00,8F,D3,36,00,00,00,00,00

COMPONENT BE,EF,02,06,00,5E,D2,37,00,00,00,00,00

COMPOSITE BE,EF,02,06,00,A1,D2,38,00,00,00,00,00

S-VIDEO BE,EF,02,06,00,70,D3,39,00,00,00,00,00

HDMI 1 BE,EF,02,06,00,43,D3,3A,00,00,00,00,00

HDMI 2 BE,EF,02,06,00,92,D2,3B,00,00,00,00,00

USB A BE,EF,02,06,00,25,D3,3C,00,00,00,00,00

USB B BE,EF,02,06,00,F4,D2,3D,00,00,00,00,00

LAN BE,EF,02,06,00,8A,DF,63,00,00,00,00,00

QUICK KEY

MENU BE,EF,02,06,00,C8,D7,01,00,00,00,00,00

UP BE,EF,02,06,00,FB,D7,02,00,00,00,00,00

DOWN BE,EF,02,06,00,2A,D6,03,00,00,00,00,00

LEFT BE,EF,02,06,00,9D,D7,04,00,00,00,00,00

RIGHT BE,EF,02,06,00,4C,D6,05,00,00,00,00,00

ENTER BE,EF,02,06,00,E6,D6,0F,00,00,00,00,00

Page 61

RESYNC BE,EF,02,06,00,F2,D5,1B,00,00,00,00,00

ASPECT BE,EF,02,06,00,C7,D2,3E,00,00,00,00,00

MUTE BE,EF,02,06,00,16,D3,3F,00,00,00,00,00

FREEZE BE,EF,02,06,00,D9,D8,40,00,00,00,00,00

BLANK BE,EF,02,06,00,08,D9,41,00,00,00,00,00

SOURCE BE,EF,02,06,00,7F,D6,06,00,00,00,00,00

OTHER FUNCTION

DCR ON

DCR OFF

BE,EF,02,06,00,EA,D8,43,00,00,00,00,00

BE,EF,02,06,00,5D,D9,44,00,00,00,00,00

ECO ON BE,EF,02,06,00,8C,D8,45,00,00,00,00,00

ECO OFF BE,EF,02,06,00,BF,D8,46,00,00,00,00,00

VOLUME INC BE,EF,02,06,00,6E,D9,47,00,00,00,00,00

VOLUME DEC BE,EF,02,06,00,91,D9,48,00,00,00,00,00

KEYSTONE INC BE,EF,02,06,00,40,D8,49,00,00,00,00,00

KEYSTONE DEC BE,EF,02,06,00,73,D8,4A,00,00,00,00,00

FACTORY RESET BE,EF,02,06,00,A2,D9,4B,00,00,00,00,00

LAMP HOURS RESET BE,EF,02,06,00,15,D8,4C,00,00,00,00,00

FILTER HOURS RESET BE,EF,02,06,00,C4,D9,4D,00,00,00,00,00

Page 62

IR Control Code

System Code: 83F4 Format : NEC

HDMI1

Video

HDMI2 Compo

Auto

Enter

Swap

Default

Page 63

Customer Support

For technical support or product service, see the table below or contact your reseller.

Note : You will need the product serial number.

Country/Region Website

Australia/New Zealand www.viewsonic.com.au

Canada www.viewsonic.com

Europe www.viewsoniceurope.com www.viewsoniceurope.com/uk/support/call-desk/ Hong Kong www.hk.viewsonic.com T= 852 3102 2900 service@hk.viewsonic.com India www.in.viewsonic.com T= 1800 266 0101 service@in.viewsonic.com Korea www.kr.viewsonic.com T= 080 333 2131 service@kr.viewsonic.com Latin America (Argentina) www.viewsonic.com/la/ T= 0800-4441185 soporte@viewsonic.com Latin America (Chile) www.viewsonic.com/la/ T= 1230-020-7975 soporte@viewsonic.com Latin America (Columbia) Latin America (Mexico) www.viewsonic.com/la/ T= 001-8882328722 soporte@viewsonic.com Renta y Datos, 29 SUR 721, COL. LA PAZ, 72160 PUEBLA, PUE. Tel: 01.222.891.55.77 CON 10 LINEAS Electroser, Av Reforma No. 403Gx39 y 41, 97000 Mérida, Yucatán. Tel: 01.999.925.19.16 Other places please refer to http://www.viewsonic.com/la/soporte/index.htm#Mexico Latin America (Peru) www.viewsonic.com/la/ T= 0800-54565 soporte@viewsonic.com Macau www.hk.viewsonic.com T= 853 2870 0303 service@hk.viewsonic.com Middle East ap.viewsonic.com/me/ Contact your reseller service@ap.viewsonic.com

Puerto Rico & Virgin Islands

Singapore/Malaysia/ Thailand South Africa ap.viewsonic.com/za/ Contact your reseller service@ap.viewsonic.com

United States www.viewsonic.com

www.viewsonic.com/la/ T= 01800-9-157235 soporte@viewsonic.com

www.viewsonic.com

www.viewsonic.com.sg T= 65 6461 6044 service@sg.viewsonic.com

T = Telephone F = FAX

AUS= 1800 880 818 NZ= 0800 008 822 T (Toll-Free)= 1-866-463-4775 T (Toll)= 1-424-233-2533 F= 1-909-468-3757

T= 1-800-688-6688 (English) T= 1-866-379-1304 (Spanish) F= 1-909-468-3757

T (Toll-Free)= 1-800-688-6688 T (Toll)= 1-424-233-2530 F= 1-909-468-3757

service@au.viewsonic.com

service.ca@viewsonic.com

service.us@viewsonic.com soporte@viewsonic.com

service.us@viewsonic.com

Page 64

Limited Warranty

ViewSonic® Projector

What the warranty covers:

ViewSonic warrants its products to be free from defects in material and workmanship, under normal use, during the warranty period. If a product proves to be defective in material or workmanship during the warranty period, ViewSonic will, at its sole option, repair or replace the product with a like product. Replacement product or parts may include remanufactured or refurbished parts or components.

Limited Three (3) year General Warranty

Subject to the more limited one (1) year warranty set out below, North and South America: Three (3) years warranty for all parts excluding the lamp, three (3) years

for labor, and one (1) year for the original lamp from the date of the rst consumer

purchase. Other regions or countries: Please check with your local dealer or local ViewSonic

ofce for the warranty information.

Limited One (1) year Heavy Usage Warranty:

Under heavy usage settings, where a projector’s use includes more than fourteen (14) hours average daily usage, North and South America: One (1) year warranty for all parts excluding the lamp, one (1) year for labor, and ninety (90) days for the

original lamp from the date of the rst consumer purchase; Europe: One (1) year

warranty for all parts excluding the lamp, one (1) year for labor, and ninety (90) days

for the original lamp from the date of the rst consumer purchase.

Other regions or countries: Please check with your local dealer or local ViewSonic

ofce for the warranty information. Lamp warranty subject to terms and conditions, verication and approval. Applies to

manufacturer’s installed lamp only. All accessory lamps purchased separately are warranted for 90 days.

Who the warranty protects:

This warranty is valid only for the rst consumer purchaser.

What the warranty does not cover:

1. Any product on which the serial number has been defaced, modied or removed.

2. Damage, deterioration, failure, or malfunction resulting from:

a. Accident, abuse, misuse, neglect, re, water, lightning, or other acts of nature,

improper maintenance, unauthorized product modication, or failure to follow

instructions supplied with the product.

b. Operation outside of product specications.

c. Operation of the product for other than the normal intended use or not under

normal conditions. d. Repair or attempted repair by anyone not authorized by ViewSonic. e. Any damage of the product due to shipment. f. Removal or installation of the product.

g. Causes external to the product, such as electric power uctuations or failure. h. Use of supplies or parts not meeting ViewSonic’s specications.

i. Normal wear and tear. j. Any other cause which does not relate to a product defect.

3. Removal, installation, and set-up service charges.

Page 65

How to get service:

1. For information about receiving service under warranty, contact ViewSonic Customer Support (please refer to “Customer Support” page). You will need to provide your product’s serial number.

2. To obtain warranted service, you will be required to provide (a) the original dated sales slip, (b) your name, (c) your address, (d) a description of the problem, and (e) the serial number of the product.

3. Take or ship the product freight prepaid in the original container to an authorized ViewSonic service center or ViewSonic.

4. For additional information or the name of the nearest ViewSonic service center, contact ViewSonic.

Limitation of implied warranties:

There are no warranties, express or implied, which extend beyond the description

contained herein including the implied warranty of merchantability and tness for a

particular purpose.

Exclusion of damages:

ViewSonic’s liability is limited to the cost of repair or replacement of the product. ViewSonic shall not be liable for:

1. Damage to other property caused by any defects in the product, damages based

upon inconvenience, loss of use of the product, loss of time, loss of prots, loss of

business opportunity, loss of goodwill, interference with business relationships, or other commercial loss, even if advised of the possibility of such damages.

2. Any other damages, whether incidental, consequential or otherwise.

3. Any claim against the customer by any other party.

Effect of local law:

This warranty gives you specic legal rights, and you may also have other rights

which vary from local authority. Some local governances do not allow limitations on implied warranties and/or do not allow the exclusion of incidental or consequential damages, so the above limitations and exclusions may not apply to you.

Sales outside the U.S.A. and Canada:

For warranty information and service on ViewSonic products sold outside of the U.S.A. and Canada, contact ViewSonic or your local ViewSonic dealer. The warranty period for this product in mainland China (Hong Kong, Macao and Taiwan Excluded) is subject to the terms and conditions of the Maintenance Guarantee Card. For users in Europe and Russia, full details of warranty provided can be found in www.viewsoniceurope.com under Support/Warranty Information.

Projector Warranty Term Template In UG VSC_TEMP_2005

Page 66

Mexico Limited Warranty

ViewSonic® Projector

What the warranty covers:

How long the warranty is effective:

3 years for all parts excluding the lamp, 3 years for labor, 1 year for the original lamp from the date of

the rst consumer purchase. Lamp warranty subject to terms and conditions, verication and approval. Applies to manufacturer’s

installed lamp only. All accessory lamps purchased separately are warranted for 90 days.

Who the warranty protects:

This warranty is valid only for the rst consumer purchaser.

What the warranty does not cover:

1. Any product on which the serial number has been defaced, modied or removed.

2. Damage, deterioration or malfunction resulting from:

a. Accident, misuse, neglect, re, water, lightning, or other acts of nature, unauthorized product

modication, unauthorized attempted repair, or failure to follow instructions supplied with the

product.

b. Any damage of the product due to shipment.

c. Causes external to the product, such as electrical power uctuations or failure. d. Use of supplies or parts not meeting ViewSonic’s specications.

e. Normal wear and tear. f. Any other cause which does not relate to a product defect.

3. Any product exhibiting a condition commonly known as “image burn-in” which results when a static image is displayed on the product for an extended period of time.

4. Removal, installation, insurance, and set-up service charges.

How to get service:

For information about receiving service under warranty, contact ViewSonic Customer Support (Please refer to the attached Customer Support page). You will need to provide your product’s serial number, so please record the product information in the space provided below on your purchase for your future use. Please retain your receipt of proof of purchase to support your warranty claim. For Your Records Product Name: ________________________ Model Number: ____________________________ Document Number: ____________________ Serial Number: ____________________________ Purchase Date: ________________________ Extended Warranty Purchase? _____________(Y/N) If so, what date does warranty expire? __________

1. To obtain warranty service, you will be required to provide (a) the original dated sales slip, (b) your name, (c) your address, (d) a description of the problem, and (e) the serial number of the product.

2. Take or ship the product in the original container packaging to an authorized ViewSonic service center.

3. Round trip transportation costs for in-warranty products will be paid by ViewSonic.

Limitation of implied warranties:

There are no warranties, express or implied, which extend beyond the description contained herein

including the implied warranty of merchantability and tness for a particular purpose.

Exclusion of damages:

ViewSonic’s liability is limited to the cost of repair or replacement of the product. ViewSonic shall not be liable for:

1. Damage to other property caused by any defects in the product, damages based upon

inconvenience, loss of use of the product, loss of time, loss of prots, loss of business opportunity,

loss of goodwill, interference with business relationships, or other commercial loss, even if advised of the possibility of such damages.

2. Any other damages, whether incidental, consequential or otherwise.

3. Any claim against the customer by any other party.

4. Repair or attempted repair by anyone not authorized by ViewSonic.

Page 67

Contact Information for Sales & Authorized Service (Centro Autorizado de Servicio) within Mexico:

Name, address, of manufacturer and importers:

México, Av. de la Palma #8 Piso 2 Despacho 203, Corporativo Interpalmas, Col. San Fernando Huixquilucan, Estado de México Tel: (55) 3605-1099 http://www.viewsonic.com/la/soporte/index.htm

NÚMERO GRATIS DE ASISTENCIA TÉCNICA PARA TODO MÉXICO: 001.866.823.2004

Hermosillo:

Distribuciones y Servicios Computacionales SA de CV. Calle Juarez 284 local 2 Col. Bugambilias C.P: 83140 Tel: 01-66-22-14-9005 E-Mail: disc2@hmo.megared.net.mx

Puebla, Pue. (Matriz):

RENTA Y DATOS, S.A. DE C.V. Domicilio: 29 SUR 721 COL. LA PAZ 72160 PUEBLA, PUE. Tel: 01(52).222.891.55.77 CON 10 LINEAS E-Mail: datos@puebla.megared.net.mx

Chihuahua

Soluciones Globales en Computación C. Magisterio # 3321 Col. Magisterial Chihuahua, Chih. Tel: 4136954 E-Mail: Cefeo@soluglobales.com

Distrito Federal:

QPLUS, S.A. de C.V. Av. Coyoacán 931 Col. Del Valle 03100, México, D.F. Tel: 01(52)55-50-00-27-35 E-Mail : gacosta@qplus.com.mx

Guerrero Acapulco

GS Computación (Grupo Sesicomp) Progreso #6-A, Colo Centro 39300 Acapulco, Guerrero Tel: 744-48-32627

MERIDA:

ELECTROSER Av Reforma No. 403Gx39 y 41 Mérida, Yucatán, México CP97000 Tel: (52) 999-925-1916 E-Mail: rrrb@sureste.com

Tijuana:

STD Av Ferrocarril Sonora #3780 L-C Col 20 de Noviembre Tijuana, Mexico

Villahermosa:

Compumantenimietnos Garantizados, S.A. de C.V. AV. GREGORIO MENDEZ #1504 COL, FLORIDA C.P. 86040 Tel: 01 (993) 3 52 00 47 / 3522074 / 3 52 20 09 E-Mail: compumantenimientos@prodigy.net.mx

Veracruz, Ver.:

CONEXION Y DESARROLLO, S.A DE C.V. Av. Americas # 419 ENTRE PINZÓN Y ALVARADO Fracc. Reforma C.P. 91919 Tel: 01-22-91-00-31-67 E-Mail: gacosta@qplus.com.mx

Cuernavaca

Compusupport de Cuernavaca SA de CV Francisco Leyva # 178 Col. Miguel Hidalgo C.P. 62040, Cuernavaca Morelos Tel: 01 777 3180579 / 01 777 3124014 E-Mail: aquevedo@compusupportcva.com

Guadalajara, Jal.:

SERVICRECE, S.A. de C.V. Av. Niños Héroes # 2281 Col. Arcos Sur, Sector Juárez 44170, Guadalajara, Jalisco Tel: 01(52)33-36-15-15-43 E-Mail: mmiranda@servicrece.com

Monterrey:

Global Product Services Mar Caribe # 1987, Esquina con Golfo Pérsico Fracc. Bernardo Reyes, CP 64280 Monterrey N.L. México Tel: 8129-5103 E-Mail: aydeem@gps1.com.mx

Oaxaca, Oax.:

CENTRO DE DISTRIBUCION Y SERVICIO, S.A. de C.V. Murguía # 708 P.A., Col. Centro, 68000, Oaxaca Tel: 01(52)95-15-15-22-22 Fax: 01(52)95-15-13-67-00 E-Mail. gpotai2001@hotmail.com

FOR USA SUPPORT:

ViewSonic Corporation 381 Brea Canyon Road, Walnut, CA. 91789 USA

Tel: 800-688-6688 (English); 866-323-8056 (Spanish);

Fax: 1-800-685-7276 E-Mail: http://www.viewsonic.com

Projector Mexico Warranty Term Template In UG VSC_TEMP_2006

Page 68

ViewSonic PRO8520HD User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual

Introduction

Projector Features

Package Contents

Projector Overview

Using the Product

Control Panel

Connection Ports

Remote Control

Installing the Batteries

Remote Control Operation

Connection

Connecting a computer or monitor

Connecting Video source devices

Operation

Powering On/Off the Projector

Adjusting the Projector Height

Adjusting the Projector Zoom and Focus

Adjusting Projection Image Size

Locking control keys

Menu Operation

Controlling the projector through a LAN environment

Controlling the projector through a web browser

Displaying images through vsPresenter

Displaying pictures with a USB storage device

Maintenance

Cleaning the Lens

Cleaning the Projector Housing

Cleaning the Filter Cover

Replacing the Lamp

Specifications

Dimensions

Ceiling mount installation

Appendix

LED Indicator Messages

Compatibility Modes

Troubleshooting

RS-232 Command and Configuration

IR Control Code