ViewSonic M1 VS17337 User Manual

M1
Portable Cinema

User Guide

Model No. VS17337

IMPORTANT: Please read this User Guide to obtain important information on installing
and using your product in a safe manner, as well as registering your product for future
service. Warranty information contained in this User Guide will describe your limited
coverage from ViewSonic Corporation, which is also found on our web site at http://

www.viewsonic.com in English, or in specic languages using the Regional selection

box in the upper right corner of our website. “Antes de operar su equipo lea cu
idadosamente las instrucciones en este manual”

i

Compliance Information

FCC Statement

This device complies with part 15 of FCC Rules. Operation is subject to the follow­ing two conditions: (1) this device may not cause harmful interference, and (2) this
device must accept any interference received, including interference that may cause
undesired operation.

This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installa­tion. This equipment generates, uses, and can radiate radio frequency energy, and
if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that interfer­ence will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the

equipment o󰀨 and on, the user is encouraged to try to correct the interference by one

or more of the following measures:

y Reorient or relocate the receiving antenna.
y Increase the separation between the equipment and receiver.
y Connect the equipment into an outlet on a circuit di󰀨erent from that to which the

receiver is connected.

y Consult the dealer or an experienced radio/TV technician for help.

Warning: You are cautioned that changes or modications not expressly approved

by the party responsible for compliance could void your authority to operate the
equipment.

For Canada

CAN ICES-3 (B)/NMB-3(B)

CE Conformity for European Countries

The device complies with the EMC Directive 2014/30/EU and Low Voltage
Directive 2014/35/EU.

Following information is only for EU-member states:

The mark is in compliance with the Waste Electrical and Electronic
Equipment Directive 2012/19/EU (WEEE).

The mark indicates the requirement NOT to dispose the equipment
including any spent or discarded batteries or accumulators as unsorted
municipal waste, but use the return and collection systems available.

If the batteries, accumulators and button cells included with this equipment,
display the chemical symbol Hg, Cd, or Pb, then it means that the battery
has a heavy metal content of more than 0.0005% Mercury or more than,

0.002% Cadmium, or more than 0.004% Lead.

ii

Important Safety Instructions

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this unit near water.

6. Clean with a soft, dry cloth.

7. Do not block any ventilation openings. Install the unit in accordance with the
manufacturer’s instructions.

8. Do not install near any heat sources such as radiators, heat registers, stoves,

or other devices (including ampliers) that produce heat.

9. Do not defeat the safety purpose of the polarized or grounding-type plug. A
polarized plug has two blades with one wider than the other. A grounding type
plug has two blades and a third grounding prong. The wide blade and the third
prong are provided for your safety. If the provided plug does not t into your
outlet, consult an electrician for replacement of the obsolete outlet.

10. Protect the power cord from being walked on or pinched particularly at plugs.

Convenience receptacles and the point where they exit from the unit. Be sure
that the power outlet is located near the unit so that it is easily accessible.

11. Only use attachments/accessories specied by the manufacturer.

12. Use only with the cart, stand, tripod, bracket, or table specied by

the manufacturer, or sold with the unit. When a cart is used, use
caution when moving the cart/unit combination to avoid injury from
tipping over.

13. Unplug this unit when unused for long periods of time.

14. Refer all servicing to qualied service personnel. Servicing is required when the

unit has been damaged in any way, such as: if the power-supply cord or plug is
damaged, if liquid is spilled onto or objects fall into the unit, if the unit is exposed
to rain or moisture, or if the unit does not operate normally or has been dropped.

iii

Declaration of RoHS2 Compliance

This product has been designed and manufactured in compliance with Directive
2011/65/EU of the European Parliament and the Council on restriction of the use
of certain hazardous substances in electrical and electronic equipment (RoHS2
Directive) and is deemed to comply with the maximum concentration values issued
by the European Technical Adaptation Committee (TAC) as shown below:

Substance

Proposed Maximum
Concentration

Actual Concentration

Lead (Pb) 0.1% < 0.1%
Mercury (Hg) 0.1% < 0.1%
Cadmium (Cd) 0.01% < 0.01%
Hexavalent Chromium (Cr

6+

) 0.1% < 0.1%
Polybrominated biphenyls (PBB) 0.1% < 0.1%
Polybrominated diphenyl ethers (PBDE) 0.1% < 0.1%

Certain components of products as stated above are exempted under the Annex III
of the RoHS2 Directives as noted below:

Examples of exempted components are:

1. Lead in glass of cathode ray tubes.

2. Lead in glass of uorescent tubes not exceeding 0.2% by weight.

3. Lead as an alloying element in aluminium containing up to 0.4% lead by weight.

4. Copper alloy containing up to 4% lead by weight.

5. Lead in high melting temperature type solders (i.e. lead-based alloys containing
85% by weight or more lead).

6. Electrical and electronic components containing lead in a glass or ceramic other
than dielectric ceramic in capacitors, e.g. piezoelectronic devices, or in a glass or
ceramic matrix compound.

iv

Copyright Information

Copyright © ViewSonic® Corporation, 2018. All rights reserved.
Macintosh and Power Macintosh are registered trademarks of Apple Inc.
Microsoft, Windows, Windows NT, and the Windows logo are registered trademarks
of Microsoft Corporation in the United States and other countries.
ViewSonic, the three birds logo, OnView, ViewMatch, and ViewMeter are registered
trademarks of ViewSonic Corporation.
VESA is a registered trademark of the Video Electronics Standards Association.
DPMS and DDC are trademarks of VESA.
PS/2, VGA and XGA are registered trademarks of International Business Machines
Corporation.
Disclaimer: ViewSonic Corporation shall not be liable for technical or editorial errors
or omissions contained herein; nor for incidental or consequential damages resulting
from furnishing this material, or the performance or use of this product.
In the interest of continuing product improvement, ViewSonic Corporation reserves
the right to change product specications without notice. Information in this docu­ment may change without notice.
No part of this document may be copied, reproduced, or transmitted by any means,

for any purpose without prior written permission from ViewSonic Corporation.

Product Registration

To fulfill possible future product needs, and to receive additional product information
as it becomes available, please visit your region section on ViewSonic’s website to
register your product online.
The ViewSonic CD also provides an opportunity for you to print the product
registration form. Upon completion, please mail or fax to a respective ViewSonic
office. To find your registration form, use the directory “:\CD\Registration”.
Registering your product will best prepare you for future customer service needs.
Please print this user guide and fill the information in the “For Your Records” section.
For additional information, please see the “Customer Support” section in this guide.

For Your Records

Product Name: M1

ViewSonic LED Projector

Model Number: VS17337
Document Number: M1_UG_ENG Rev. 1C 09-12-18
Serial Number: ________________________________________
Purchase Date: ________________________________________

Product disposal at end of product life

ViewSonic respects the environment and is committed to working and living green.
Thank you for being part of Smarter, Greener Computing. Please visit ViewSonic
website to learn more.
USA & Canada: http://www.viewsonic.com/company/green/recycle-program/
Europe: http://www.viewsoniceurope.com/eu/support/call-desk/
Taiwan: http://recycle.epa.gov.tw

v

Table of Contents

Introduction ........................................................................ 1

Projector features .................................................................................................................1

Shipping contents ............................................................. 2

Package Overview................................................................................................................2

Product Overview .................................................................................................................3

Controls and functions .................................................... 4

Setting up .......................................................................... 7

Power On/O󰀨 ........................................................................................................................8

Mount the Projector ........................................................................................................... 10

Open the smart stand and adjust the focus ring .................................................................11

Adjust Projected Image ..................................................................................................... 12

Positioning your projector .............................................. 13

Using the menus................................................................................................................ 14

Adjusting your projector’s settings ..................................................................................... 16

Connect the projector to your device ................................................................................. 17

Di󰀨erent menu options ...................................................................................................... 18

M1 FW Upgrade ................................................................................................................ 20

Wallpaper .......................................................................................................................... 21

Image Settings................................................................................................................... 21

About the aspect ratio........................................................................................................ 22

Auto Keystone ................................................................................................................... 23

V Keystone ........................................................................................................................ 23

Brightness.......................................................................................................................... 23

Contrast ............................................................................................................................. 23

Optimizing the image ......................................................................................................... 24

Harman Kardon - Adjusting the audio settings .................................................................. 24

Muting the Sound .............................................................................................................. 24

Adjusting the Sound level .................................................................................................. 24

vi

Adjusting the Audio Mode .................................................................................................. 25

Adjusting the Light source settings .................................................................................... 25

Reset All Settings .............................................................................................................. 26

Eye Protection ................................................................................................................... 26

Viewing di󰀨erent le .......................................................................................................... 26

Using the 3D function ........................................................................................................ 30

OSD Menu System ............................................................................................................ 32

Specication sheet ............................................................................................................ 34

HDMI Support Video Timing .............................................................................................. 36

HDMI Support PC Timing .................................................................................................. 37

3D Support Timing ............................................................................................................. 38

USB-C Support Timing ...................................................................................................... 39

1

Introduction

Projector features

The Portable Cinema providing users with high-performance LED projection and a user­friendly design to deliver high reliability and ease of use.

Some of the features may not be available on your projector. Actual performance may

vary and subject to model specications.

• 360 degree smart stand enable instant Power ON / OFF (with Lens cover function).

• Auto keystone to correct distorted image automatically.

• Eye Protection function avoiding objects get close to the direct light from optical

engine (30cm distance / 30 degree).

• USB-C for video transmission and power supply.

• Embedded battery for easy outdoor projection (up to 6 hours).

• Switchable light source mode to extend your battery usage hours.

• 16GB internal storage ( Max. 12GB available storage for users).

• User-friendly UI design for easy navigation.

• Music mode enables users to enjoy music without projection image.

• Short throw lens design to allow 1.6m distance to project 60” screen size.

• LED light source with excellent light source life (30,000 hrs).

• Supports 3D display.

• Color modes providing choices for di󰀨erent projection purposes.

• Multi-language On-Screen Display (OSD) menus.

The apparent brightness of the projected image will vary depending on the ambient lighting
conditions, selected input signal contrast/brightness settings, and is directly proportional to
projection distance.

2

Shipping contents

Package Overview

Carefully unpack and verify that you have all of the items shown below. If any of these
items are missing, please contact your place of purchase.

Projector AC Power Cord AC Power Adapter

Quick Start Guide

Quick Start Guide

Quick Start Guide

USB-C Cable (1M) Remote Control (with batteries) Soft Carrying Bag Quick Start Guide

Others

• Warranty Card (for specic regions ONLY)

NOTES

• Duetodi󰀨erentapplicationsineachCountry,someregionsmayhavedi󰀨erentaccessories..

• Make sure to properly discard the used batteries according to local regulations.

3

Product Overview

1

2

8 10

3

2

3

3

ENTER

1

2

5 6 7

8 10

9

12

11

20

3

4

ENTER

2

5 6

7

8 10

9

12

11

20

3

ENTER

7

8 10

9

12

11

20

3

ENTER

1

2

5 6 7

8 10

19

1513 16 17 18

9

12

11

20

3

4

14

ENTER

5 6 7

8 10

19

1513 16 17 18

9

12

11

20

3

14

1. Speaker

2. Ventilation

3. Focus Ring

4. Tripod hole

5. IR receiver

6. Eye Protection sensor

7. Enter / Power button

8. Volume - / Down

9. Volume + / Up

10. Return

11. Battery indicator

12. Speaker PR

13. Micro SD

14. DC in

15. USB-C

16. HDMI port

17. Headphone

18. USB Reader (5V1A out)

19. Reset button**

20. 360 degree smart stand

** Insert a paper clip into the reset button to restart the projector if system freezing.

4

Controls and functions

Projector

ENTER

ENTER

Power / Enter

- Press 3 seconds to power on/o󰀨 the projector

- Enacts the selected On-Screen Display(OSD) menu item.

Volume down

- Decrease the volume level.

- Down

Volume up

- Increase the volume level.

- Up

Return

- Return to the previous stage/level

Battery indicator light

- Indicates the status of the embedded battery.

5

Remote Control

1

3

6

9

11

15

2
4

5

7
10

8
12

14

13

1. Power button

2. Settings

3. Home

4. Harman Kardon Settings

5. Music Mode*

6. UP / KEYSTONE

7. OK

8. DOWN / KEYSTONE

9. LEFT / BACKWARD

10. RIGHT / FORWARD

11. MUTE

12. PLAY / PAUSE

13. RETURN

14. Volume Up

15. Volume Down

*Blank the projection image and focus on the music enjoyment.

Remotecontrole󰀨ectiverange

Refer to the illustration about the location of the Infra-Red (IR) remote control sensor(s).
The remote control must be held at an angle within 30 degrees perpendicular to the
projector’s IR remote control sensor(s) to function correctly. The distance between the
remote control and the sensor(s) should not exceed 8 meters (~26 feet).

Make sure that there are no obstacles between the remote control and the III sensor(s) on
the projector that might obstnict the infra-red beam.

6

Replacing the remote control battery

1. To open the battery cover, turn the remote control over to view its back, open the
cover in the direction of the arrow as illustrated.

2. Remove any existing batteries (if necessary) and install two AAA batteries observing
the battery polarities as indicated in the base of the battery compartment. Positive (+)
goes to positive and negative (-) goes to negative.

3. Ret the cover by aligning it with the base and pushing it back down into position.
Stop when it clicks into place.

Warning

• Avoid leaving the remote control and batteries in an excessive heat or humid environment like the kitchen,

bathroom, sauna, sunroom or in a closed car.

• Replace only with the same or equivalent type recommended by the battery manufacturer.

• Dispose of the used batteries according to the manufacturer’s instructions and local environment regulations

for your region.

• Neverthrowthebatteriesintoare.Theremaybedangerofanexplosion.

• If the batteries are drained or if you will not be using the remote control for an extended period of time, remove

the batteries to avoid damage to the remote control from possible battery leakage.

7

Setting up

Operating your projector

This portable projector allows you to plug and play your devices so you can easily open

multimedia les and hear audio straight from it’s built-in Harman Kardon speakers.

For your safety and to maintain the quailty of this unit, refer to the following steps when
operating your Projector.

8

PowerOn/O󰀨

Using power cord

1. Connect the power cord to the power adapter.

2. Connect the AC power cord to a power source

3. Connect the DC power connector to your projector.

Chargetheprojectorfor3hoursbeforeusingitinbatterymodeforthersttime.

IMPORTANT!

• Use only the bundled power adapter to change the battery pack and supply power to your LED projector.

• EnsurethatyourLEDprojectorisconnectedtothepoweradapterbeforeturningitonforthersttime.We

strongly recommend that you use a grounded wall socket while using your LED projector on power adapter
mode.

• The socket outlet must be easily accessible and near your LED projector.

• To disconnect your LED projector from its main power supply, unplug your LED projector from the power

socket.

Warning

Read the following precautions for your LED projector’s battery.

• Thebatteryusedinthisdevicemaypresentariskofreorchemicalburnifremovedordisassembled.

• Followthewarninglabelsforyourpersonalsafety.•Riskofexplosionifbatteryisreplacedbyanincorrect

type.

• Donotdisposeofinre.•Neverattempttoshort-circuityourLEDprojector’sbattery.

• Never attempt to dissemble and reassemble the battery.

• Discontinueusageifleakageisfound.•Thebatteryanditscomponentsmustberecycledordisposedof

properly.

• Keep the battery and other small components away from children,

9

Using The Battery

Warning message is displayed when the battery is running out.

As your battery is low, the projector will be turned o󰀨 in a minute.

If the screen shows a low battery message, be sure to charge the battery.

Battery using time information

Status Time and Display
Charging About 3 hours

Usage Hours

Up to 6hrs battery life (with Battery Saving mode and without
USB power supply)

Battery Level indicator
(Charging)

• During charging: Power button with Red LED light up

• Full charge: Power button with White LED light up

There will be a very low power consumption during standby mode, suggest to full charge the
battery before usage every time.

10

Mount the Projector

Screw a standard tripod into the screw hole on the projector.

The tripod is not included.

+

Bottom side of the

projector

Bolt used to
attach the
projector

The projector is

connected to this part

Tripod

11

Open the smart stand and adjust the focus ring

• Open the smart stand by moving its lens cover down

• Adjust the image focus of the projection onscreen by moving the focus ring up and

down.

12

Adjust Projected Image

The projector is equipped with a smart stand for adjusting the projected image

Using Auto Keystone to adjust image (refer to details in Page 29)

13

Positioning your projector

Screen size and projection distance table

Adjust the LED projector’s distance from the screen using the below table:

(a) Screen Size

16:9 image on a 16:9 Screen

(b) Image Width (c) Image height (d) Projection Distance

inch mm inch mm inch mm inch mm

24 610 21 531 12 299 25 637
30 762 26 664 15 373 31 796
40 1016 35 885 20 498 42 1062
50 1270 44 1106 25 622 52 1327
60 1524 52 1327 29 747 63 1593
70 1778 61 1549 34 871 73 1858
80 2032 70 1770 39 996 84 2124
90 2286 78 1991 44 1120 94 2389

100 2540 87 2212 49 1245 105 2655

14

Using the menus

The projector is equipped with On-Screen Display (OSD) menus for making various
adjustments and settings.

The OSD screenshots below are for reference only, and may di󰀨er from the actual design.

Below is the overview of the OSD menu.

Battery
indicator

Wallpaper

Settings

Information

Input
Source
Selection

15

Launch the onscreen display by opening the smart stand of your projector
OSD menus will be shown after ViewSonic start up screen.

To use the OSD menus, please select your language rst.

1. Press Settings button on remote to turn the OSD setting page on

2. Use < / > to highlight the Settings menu.

3. Press ▼ to highlight language and press to select a preferred Language.

4. Press OK to save the settings

5. Press Return / Home button to leave or return to Home page.

16

Adjusting your projector’s settings

Refer to the following steps when accessing the onscreen display menu options to adjust
your projector settings:

1. Launch the onscreen display menu

2. Press< / >to select the menu option you would like to access

3. Press < / > to adjust the settings according to your preference.

4. Press OK to save the new settings.

5. Press settings to go back the settings page

6. Press Home to go back to the home page

2
4

5

7
10

8
12

14

13

17

Connect the projector to your device

1

3

2

4

5

1. Please use the supplied USB-C cable to make sure the compatibility.

2. Please make sure your USB-C device can support video transmission

1

Micro SD

- SDHC (up to 32GB)

- FAT32 / NTFS

2

USB-C

- USB-C with power supply only supported
under DC in situation.

3

HDMI

- iPhone/iPad need to buy additional
adapter, to avoid compatible issue,
please use Apple authorized accessories

4

USB Reader

- FAT32 / NTFS

- Hard disk support up to 1TB

5 USB Power Supply (5V1A)

18

Di󰀨erentmenuoptions

Switching input signal

Di󰀨erent input signals can be used to connect with the projector.

1. Di󰀨erent source is shown on the OSD homepage.

2. Press < / > until your desire signal is selected and press OK.
Once detected, the selected source information will be displayed on the screen for

seconds.

HDMI 1.4 / HDCP 1.4 support timing:

480i

480p

576i

576p
720/50p
720/60p

1080/24P
1080/25P
1080/30P

1080/50i

1080/60i
1080/50P
1080/60P

19

USB C Conditions:

• Using Power adapter: Video & Data trasmission / Power Supply

• Using Embedded battery: Video & Data transmission

USB Reader

• Flash Drive support up to 128GB

• Format: FAT32 / NTFS

• Hard disk support up to 1TB

• FW update

20

M1 FW Upgrade

1. Copy FW “MstarUpgrade.bin” from ViewSonic website

2. Power on the projector

3. Plug in USB with new FW (USB Format: FAT32)

4. Auto detect and pop up FW upgrade conrmation message

5. Click “Conrm”

6. Page with the loading bar will be appeared

7. After reached 100%, will return to ViewSonic start up screen for loading again

8. The whole upgrading process will take around 5 mins

9. After nishing the process, will return to the Home page

21

Wallpaper

Select this menu option to change the OSD wallpaper.
You may select your preferred picture from the pre-installed wallpaper collection.

GO to Wallpaper > choose selected wallpaper and press OK

Wallpaper example:

Image Settings

Aspect Ratio

Go to Settings > Image Settings > Aspect Ratio
Press < / > to select an aspect ratio to suit the format of the video signal and your
display requirements, and press OK.

22

About the aspect ratio

In the picture below, the black portions are inactive areas and the white portions are active
areas. OSD menus can be displayed on those unused black areas.

1. Auto: Proportional scaling of an image to t the
projector’s natural resolution in its horizontal
width. This is suitable where the incoming image
is neither in 4:3 nor 16:9 aspect ratios but where
you want to make most use of the screen without
altering the image’s aspect ratio.

Image 16:10

Image 16:9

2. 4:3: Scales a picture so that it is displayed in the
center of the screen with a 4:3 aspect ratio. This
is most suitable for 4:3 pictures such as those for

computer monitors, standard denition TV, and

4:3 aspect DVD movies as these can be displayed
without aspect alteration.

Image 4:3

3. 16:9: Scales a picture so that it is displayed
in the center of the screen with a 16:9 aspect
ratio. This is most suitable for images which are

already in a 16:9 aspect such as high denition

TV because as these can be displayed without
aspect alteration.

Image 16:9

23

Auto Keystone

Auto Keystone provides a rectangular screen image by automatically adjusting the
Keystone number when there is a trapezoidal screen image caused by tilting of the
projector.

Go to Settings > Image Settings > Auto Keystone
Press < / > to select:

• ON: Automatically adjusts the Keystone number.

• OFF: Manually adjusts the Keystone number.

V Keystone

To prevent the screen image from becoming trapezoidal, Keystone adjusts the top and
bottom width of the image if the projector is not set at a right angle to the screen.

Go to Settings > Image Settings > V Keystone
Press < / > to adjust keystone, keystone can be adjusted from -40 to 40.

Press OK when nished.

If available, you can press keystone buttons on the remote control to adjust the projector’s
keystone.

Brightness

The higher the value, the brighter the image. And lower the
setting, darker the image. Adjusting this control so the black
areas of the image to appear just as black and that detail in
the dark areas is visible.

Go to Settings > Image Settings > Brightness
Press < / > to adjust brightness, brightness can be adjusted from 0 to 100.

Press OK when nished.

Contrast

The higher the value, the greater the contrast. Use this to
set the peak white level after you have previously adjusted
the Brightness setting to suit your selected input and viewing
environment.

Go to Settings > Image Settings> Contrast
Press < / > to adjust contrast, contrast can be adjusted from -50 to 50.

Press OK when nished.

24

Optimizing the image

Select the Display Mode

The projector is preset with several predened picture modes so that you can choose one

to suit your operating environment and input signal picture type.
To select an operation mode that suits your need, you can follow one of the following

steps.
Go to Settings > Display Mode
Press up / down to select a desired mode.

Press OK when nished.

Display Mode

Mode

Brightest

Maximizes the brightness of the projected image.
This mode is suitable for environments where high
brightness is required, such as using the projector in
well lit rooms.

Standard

Displays images in standard levels of contrast,
brightness, and sharpness.

Theater Optimizes the image for movie.

Harman Kardon - Adjusting the audio settings

The sound adjustments made as below will have an e󰀨ect on the projector speaker.

Muting the Sound

Go to Settings > Harman Kardon > MUTE
Press < / > to adjust ON / OFF.

Press OK when nished.

If available, you can press on the remote control to toggle the projector audio between on

ando󰀨.

Adjusting the Sound level

Go to Settings > Harman Kardon > Audio Volume
Press < / > to adjust volume, volume can be adjusted from 0 to 20.

Press OK when nished.

If available, you can press or on the remote control to adjust the projector’s sound level.

25

Adjusting the Audio Mode

Go to Settings > Harman Kardon > Audio Mode
Press up / down to select a desired mode.

Press OK when nished.

Sound Mode

Mode

Movie

Sets audio optimized for a specic genre.Bass Booster

Instrumental

If available, you can press Harman Kardon on the remote control to adjust the projector’s
sound mode.

Adjusting the Light source settings

Go to Settings > Light Source Mode
Press up / down to select a desired mode.

Press OK when nished.

To keep the projection playtime as long as possible, you can do the following settings via
the OSD menu.

Light Source
Mode

Mode Playtime for Battery

Full

• Default mode when
connecting with power
adapter

2.5 hours

Eco

• Default mode when
using with embedded
battery.

3 hours

Extended Eco 4 hours
Battery Saving 6 hours

Using Battery Saving mode reduces system noise and power consumption. If the Battery
saving mode is selected, the light output will be reduced and result in darker projected
pictures.

26

Reset All Settings

Returns all settings to the factory preset values.

The following settings will still remain: Language, Keystone, Go to Settings > Reset
Settings > All Settings

Press < / > to select Reset / Cancel.

Press OK when nished.

Eye Protection

To protect children’s eye on direct light damage, when an object get closer to the lens, and
will automatically turn to a blank image

Distance: 30cm / 30 degree between the lens and the object

30cm /30 degree

Object

Go to Settings > Eye Protection
Press < / > to select sensor ON / OFF.

Press OK when nished.

Viewingdi󰀨erentle

Go to Homepage > selected input source
Connect a device:

• USB Reader

• Local Storage

• Micro SD

Use up and down, </> button to select the le you want and press the OK button

27

For single le: Press OK when nished.

For multiple les: Click “Select”, boxes will be appeared in front of each le, press OK
and up/down to select multiple les. Then select Copy / Paste / Cut/ Delete under “Select”
button. Go to Homepage and select your sources again, Paste your selected les on your

desired location.

- Photo: Slide show supported

- Video: Repeat supported

- Music: Repeat / shu󰀪e supported

28

Press OK on remote control or Enter on keypad to show the control bar when playing
video / music / photo.

Control playback by using the following buttons.

Picture Video

Backward Backward

Play Fast backward

Next Play

Zoom in Pause

Zoom out Fast Forward

Rotate (left) Next

Rotate (right) Volume Control

Others (including 3D settings) Others (including 3D settings)

O󰀩cesupportformat

I.

Document
viewing function

Items Indicators
1 doc/docx Able to open and read documents in doc/docx
2 xls/xlsx Able to open and read documents in xls/xlsx
3 ppt/pptx Able to open and read documents in ppt/pptx
4 Pdf Able to open and read documents in pdf

II.

Supporting
Interface
Language

1

Supporting Interface
44 languages

English, Simplied Chinese, Chinese (TW), Chinese

(HK), Spanish (LA), French (EU), PT (EU), PT (BR),
German, Russian, Italian, Swedish, Spanish (EU),
Korean, Arabic, Farsi, Serbian, Bosnian, Macedonian,
Bulgarian, Ukrainian, Greek, Norwegian, Danish,
Czech, Hungarian, Slovak, Polish, Romanian,
Finnish, Estonian, Latvian, Lithuanian, British English,
Slovenian, Croatian, Turkish, Vietnamese, Bahasa
Indonesia, Dutch, Malay, Thai, Hindi, Hebrew,
Burmese, Catalan.

Tips for using USB reader:

- Some USB storage devices may not work or may work incorrectly.

- If you use a USB extension cable, the USB device may not be recognized or may not work properly.

- Use only USB storage devices formatted with the Windows FAT32 or NTFS le system.

- If the le size is too large or users moving too fast to next page, it will take some time for le loading.

- Data in USB storage device can be damaged so be sure to back up important les. Data maintenance is

the user’s responsibility and the manufacturer is not responsible for data loss.

29

Multimedia support format

Extension Codec
.xvid
.avi

Video Xvid, H.264
Audio MP3

.mp4
.m4v
.mov

Video H.264/MPEG 4

Audio AAC

.mkv Video H.264
.ts
.trp
.tp
.mts
.m2ts

Video H.264, MPEG2

Audio MP3/AAC

.vob

Video MPEG1, MPEG2
Audio DVD-LPCM

.mpg Video MPEG1

30

Using the 3D function

This portable cinema features 3D function which enables you to enjoy 3D movies, videos,
and sporting events in a more realistic way by presenting the depth of the images. You
need to wear a pair of 3D glasses to view 3D images.

If the 3D signal is input from an HDMI 1.4a compatible device, the portable cinema detects
the signal for 3D Sync information and once detected, it projects images in 3D format
automatically.

To activate 3D functions:

1. Press OK, video control bar will pop up when playing videos

2. Select the 3D settings icon, the 3D Settings menu is displayed in the right bottom
corner.

3. Highlight 3D self detect and change to Auto.

When the 3D Sync function is on:

• The brightness level of the projected image will decrease.

• The Color Mode cannot be adjusted.

If you discover the inversion of the 3D image depth, set the 3D Sync Invert function to ON
to correct the problem.

31

Video Control Menu

3D OSD menu

32

OSD Menu System

Menu system

Please note that the on-screen display (OSD) menus vary according to the signal type
selected.

The menu items are available when the projector detects at least one valid signal. If there
is no equipment connected to the projector or no signal detected, limited menu items are
accessible.

Source Main Menu Sub-menu Options

HDMI

3D Self Detect Manual / Auto

3D Conversion

None / Side by Side / Top &
Bottom / Frame Packing / Frame

sequential / Line alternative
3D Sync Invert ON / OFF
Hue Range : 0 ~ 100
Sharpness Range : 0 ~ 100
Saturation Range : 0 ~ 100

USB-C

3D Self Detect Manual / Auto

3D Conversion

None / Side by Side / Top &

Bottom / Frame Packing / Frame

sequential / Line alternative
3D Sync Invert ON / OFF
Hue Range : 0 ~ 100
Sharpness Range : 0 ~ 100
Saturation Range : 0 ~ 100

USB Reader

Play

Video Control Bar
(appear with icon)

Backwards / Forward / Fast

backwards / Fast Forward / Play /

Pause / Volume / settings

Photos Control Bar
(appear with icon)

Backwards / Play / Forward /

Zoom in / Zoom out / Rotate /

settings
Music Control Bar

(appear with icon)

Backwards / Play / Forward /

Repeat / Shu󰀪e

Select Copy / Paste / Cut / Delete

Local storage

Play

Video Control Bar
(appear with icon)

Backwards / Forward / Fast

backwards / Fast Forward / Play /

Pause / Volume / settings

Photos Control Bar
(appear with icon)

Backwards / Play / Forward /

Zoom in / Zoom out / Rotate /

settings
Music Control Bar

(appear with icon)

Backwards / Play / Forward /

Repeat / Shu󰀪e

Select Copy / Paste / Cut / Delete

33

Source Main Menu Sub-menu Options

Micro SD

Play

Video Control Bar
(appear with icon)

Backwards / Forward / Fast

backwards / Fast Forward / Play /

Pause / Volume / settings

Photos Control Bar
(appear with icon)

Backwards / Play / Forward /

Zoom in / Zoom out / Rotate /

settings
Music Control Bar

(appear with icon)

Backwards / Play / Forward /

Repeat / Shu󰀪e

Select Copy / Paste / Cut / Delete

Settings

Image Settings

Aspect Ratio Auto / 4:3 / 16:9
Auto Keystone ON / OFF
V Keystone V Range :+40 ~ -40 (0)
Brightness Range : 0 ~ 100
Contrast Range : -50 ~ 50

Display Mode

Brightest / Standard /
Theater / Music

Language

English/ France / Germany/
Italian/ Spanish/ Russian/

繁體中文/ 简体中文/ 日本
語/ 한국어/ Swedish/ Dutch/

Turkish/ Czech/ Portuguese/
Thai/ Polish/ Finnish/Arabic/
Indonesi/ Hindi/ Vietnam

Harman Kardon

Mute ON / OFF
Audio Volume Range :0 ~ 20 (10)

Audio Mode

Movie / Bass Booster /

Instrumental

Light Source mode

Full / Eco / Extended Eco /
Battery Saving

Reset Settings All Reset Reset / Cancel
Eye Protection ON / OFF

Wallpaper

Display Mode
Light Source Mode
Local storage

capacity
Firmware Version

34

Specicationsheet

Specication

Projection system DLP

TM

0.2” WVGA
Native Resolution 854x480
Brightness 250lm
Contrast Ratio 120000:1
Display Color 1.07 Billion Colors
Light Source LED
Light source life

(Nor/SuperEco)

30000 hours

Lamp Watt 10W RGB LED
Lens F=1.7, f=5.5mm
Projection O󰀨set 100%+/-5%
Throw Ratio 1.2
Image size 24"-100"
Throw Distance 38”@1m
Keystone +/- 40° (Vertical)
Optical Zoom Fixed
Audible Noise (Eco) 25dB

Local storage

Total 16GB

(12GB available storage)
Resolution Support VGA(640 x 480) to FullHD(1920 x 1080)
HDTV Compatibility 480i, 480p, 576i, 576p, 720p, 1080i, 1080p
Horizontal Frequency 15h~135kHz
Vertical Scan Rate 23~120Hz

Input

HDMI / HDCP 1 (HDMI 1.4 / HDCP 1.4)
SD Card Micro SD (Support up to 32GB, SDHC)
USB-C 1 (5V/ 2A)

Output

Audio out (3.5mm) 1
Speaker 3W Cube x 2
USB type A (Power) 1 (5V/ 1A)

Others

Power Supply Voltage

19.V

3.42A

(Adapter Input 100-240V @ 50/60 Hz)

Power Consumption

45W@100VAC

Standby: <0.5W
Operating Temperature 0~40°C
Carton Color
Net Weight 0.75kg
Dimensions (WxDxH) w/

adjustment foot

146x126x40mm

35

Language

English, French, Spanish, Thai, Korean, German, Italian, Russian, Swedish,

Dutch, Polish, Czech, T-Chinese, S-Chinese, Japanese, Turkish,

Portuguese, Finnish, Indonesian, India, Arabic, Vietnamese

Standard Accessory

Power Cord 1
Remote Control 1
QSG 1
USB-C Cable 1 (1m)

Optional Accessory

Warranty Card Yes (for specic regions only)
Carry Bag 1

Feature Map

SuperColor ●
3D Blu-ray ●
3D Ready ●
SonicExpert ●
SonicMode ●
360° Tilt Angle Projection ●
Porait mode ●
Auto V Keystone ●
USB Reader ●
Quick Power On ●

Quick Power O󰀨 ●
Eye Protection ●

36

HDMI Support Video Timing

Timing Resolution

Horizontal

frequency (KHz)

Vertical

frequency (Hz)

Dot Clock

Frequency (MHz)

480i 720(1440) x 480 15.73 59.94 27

480p 720 x 480 31.47 59.94 27

576i 720(1440) x 576 15.63 50 27

576p 720 x 576 31.25 50 27
720/50p 1280 x 720 37.5 50 74.25
720/60p 1280 x 720 45.00 60 74.25

1080/24P 1920 x 1080 27 24 74.25
1080/25P 1920 x 1080 28.13 25 74.25
1080/30P 1920 x 1080 33.75 30 74.25

1080/50i 1920 x 1080 28.13 50 74.25

1080/60i 1920 x 1080 33.75 60 74.25
1080/50P 1920 x 1080 56.25 50 148.5
1080/60P 1920 x 1080 67.5 60 148.5

37

HDMI Support PC Timing

Resolution Mode Refresh rate (Hz) H-frequency (kHz) Clock (MHz)

640 x 480

VGA_60 59.940 31.469 25.175
VGA_72 72.809 37.861 31.500
VGA_75 75.000 37.500 31.500
VGA_85 85.008 43.269 36.000

VGA_120 119.518 61.910 52.500

720 x 400 720x400_70 70.087 31.469 28.3221

800 x 600

SVGA_56 56.250 35.156 36.000
SVGA_60 60.317 37.879 40.000
SVGA_72 72.188 48.077 50.000
SVGA_75 75.000 46.875 49.500
SVGA_85 85.061 53.674 56.250

SVGA_120 119.854 77.425 83.000

1024 x 768

XGA_60 60.004 65.000 65.000
XGA_70 70.069 75.000 75.000
XGA_75 75.029 78.750 78.750
XGA_85 84.997 94.500 94.500

XGA_120 119.804 137.750 137.750

1152 x 864 1152 x 864_75 75.00 67.500 108.000

1280 x 768

1280 x 768_60 60 47.396 68.25
1280 x 768_60 59.870 47.776 79.5
1280 x 768_75 74.893 60.289 102.25
1280 x 768_85 84.837 68.633 117.50

1280 x 800

WXGA_60 59.810 49.702 83.500
WXGA_75 74.934 62.795 106.500
WXGA_85 84.880 71.554 122.500

1280 x 1024

SXGA_60 60.020 63.981 108.000
SXGA_75 75.025 79.976 135.000
SXGA_85 85.024 91.146 157.500

1280 x 960

1280 x 960_60 60.000 60.000 108
1280 x 960_85 85.002 85.938 148.500

1360 x 768 1360 x 768_60 60.015 47.712 85.500

1366 x768 1366 x 768_60

1440 x 900

WXGA+_60 60 55.469 88.75
WXGA+_60 59.887 55.935 106.500
WXGA+_75 74.984 70.635 136.75
WXGA+_85 84.842 80.430 157.000

1400X1050 SXGA+_60 59.978 65.317 121.750

1600x1200 UXGA 60.000 75.000 162.000

38

Resolution Mode Refresh rate (Hz) H-frequency (kHz) Clock (MHz)

1680 x 1050 1680x1050_60

59.883 64.674 119.000

59.954 65.290 146.250

1920 x 1200 1920x1200_60 59.950 74.038 154.000
640x480@67Hz MAC13 66.667 35.000 30.240
832x624@75Hz MAC16 74.546 49.722 57.280

1024x768@75Hz MAC19 75.020 60.241 80.000
1152x870@75Hz MAC21 75.06 68.68 100.00

3D Support Timing

HDMI/DP 3D (BlueRay3D with info frame)

Signal Resolution (dots) Aspect Ratio Refresh Rate (Hz) Support

Frame packing

1080p 1920 x 1080 16:9 23.98/24 Yes

720p 1280 x 720 16:9 50/59.94/60 Yes

Side by side

1080i 1920 x 1080 16:9 50/59.94/60 Yes

Top and Bottom

1080p 1920 x 1080 16:9 23.98/24 Yes

720p 1280 x 720 16:9 50/59.94/60 Yes

3D (HDMI/USB C) manual setting

Signal Resolution (dots) Aspect Ratio Refresh Rate (Hz) Support
SVGA 800 x 600 4:3 60* / 120** Yes

XGA 1024 x 768 4:3 60* / 120** Yes

HD 1280 x 720 16:9 60* / 120** Yes

WXGA 1280 x 800 16:9 60* / 120** Yes

HDTV (1080p) 1920 x 1080 16:9 60 Ye s

for Video Signal

SDTV (480i)*** 720 x 480 4:3 / 16:9 60 No
Note:
* 60Hz signals are supported for side by side, top and bottom, frame sequential
** 120 Hz signals are support for frame sequential only
*** Video signal (SDTV 480i) is support for frame sequential only

39

USB-C Support Timing

Timing Resolution

Horizontal

frequency (KHz)

Vertical

frequency (Hz)

Dot Clock

Frequency (MHz)

480i 720 (1440) x 480 15.73 59.94 27

480p 720 x 480 31.47 59.94 27

576i 720 (1440) x 576 15.63 50 27

576p 720 x 576 31.25 50 27
720/50p 1280 x 720 37.5 50 74.25
720/60p 1280 x 720 45.00 60 74.25

1080/24P 1920 x 1080 27 24 74.25
1080/25P 1920 x 1080 28.13 25 74.25
1080/30P 1920 x 1080 33.75 30 74.25

1080/50i 1920 x 1080 28.13 50 74.25

1080/60i 1920 x 1080 33.75 60 74.25
1080/50P 1920 x 1080 56.25 50 148.5
1080/60P 1920 x 1080 67.5 60 148.5

Customer Support

For technical support or product service, see the table below or contact your reseller.

Note: You will need the product serial number.

Country/Region Website

T= Telephone
C = CHAT ONLINE

Email

Australia
New Zealand

www.viewsonic.com.au

AUS= 1800 880 818
NZ= 0800 008 822

[e-mail]

Canada www.viewsonic.com T= 1-866-463-4775 [e-mail]
Europe www.viewsoniceurope.com http://www.viewsoniceurope.com/eu/support/call-desk/
Taiwan www.viewsonic.com/tw/ T= 0800-899-880 [e-mail]
Hong Kong www.hk.viewsonic.com T= 852 3102 2900 [e-mail]
India www.in.viewsonic.com T= 1800 419 0959 [e-mail]
Korea ap.viewsonic.com/kr/ T= 080 333 2131 [e-mail]
Japan www.viewsonic.com/jp/ [e-mail]
Philippines www.viewsonic.com/ph/ Contact your reseller [e-mail]
Vietnam www.viewsonic.com/vn/ Contact your reseller [e-mail]

Latin America www.viewsonic.com/la/

C= http://www.viewsonic.com/

la/soporte/servicio-tecnico

[e-mail]

Nexus Hightech Solutions, Cincinnati #40 Desp. 1 Col. De los Deportes Mexico D.F.
Tel: [phone])6547-6484
Other places please refer to http://www.viewsonic.com/la/soporte/servicio-tecnico#mexico

Macau www.hk.viewsonic.com T= (853) 2833-8407 [e-mail]
Middle East ap.viewsonic.com/me/ Contact your reseller [e-mail]

Puerto Rico &
Virgin Islands

www.viewsonic.com

T= 1-800-688-6688 (English)
C= http://www.viewsonic.com/

la/soporte/servicio-tecnico

[e-mail]
[e-mail]

Singapore www.viewsonic.com/sg/ T= 65 6461 6044 [e-mail]
Malaysia www.viewsonic.com/my/ T = 1800 - 88 - 8997 [e-mail]
Thailand www.viewsonic.com/th/ T = 02-7214091-3 [e-mail]
South Africa ap.viewsonic.com/za/ Contact your reseller [e-mail]
United States www.viewsonic.com T= 1-800-688-6688 [e-mail]

40

Limited Warranty

ViewSonic® Projector

What the warranty covers:

ViewSonic warrants its products to be free from defects in material and

workmanship, under normal use, during the warranty period. If a product proves to

be defective in material or workmanship during the warranty period, ViewSonic will,

at its sole option, repair or replace the product with a like product. Replacement

product or parts may include remanufactured or refurbished parts or components.

For warranty in North and South American, please visit the following web site for

warranty information, https://www.viewsonic.com/us/support/limited-warranties/

standard-warranty

For other regions:

Limited One (1) year General Warranty

ViewSonic’s standard warranty period is one (1) year for any product model in any

country, unless a longer warranty period is specied and provided by ViewSonic .

Please refer to the ViewSonic website in your country to check the local terms and

model variants, and see if the product model in your country is eligible for a longer

warranty period.

Limited One (1) year Heavy Usage Warranty:

Under heavy usage settings, where a projector’s use includes more than fourteen

(14) hours average daily usage, North and South America: One (1) year warranty

for all parts excluding the Light Source, one (1) year for labor, and ninety (90) days

for the original Light Source from the date of the rst consumer purchase; Europe:

One (1) year warranty for all parts excluding the Light Source, one (1) year for labor,

and ninety (90) days for the original Light Source from the date of the rst consumer

purchase.

Other regions or countries: Please check with your local dealer or local ViewSonic

o󰀩ce for the warranty information.

Light Source warranty subject to terms and conditions, verication and approval.

Applies to manufacturer’s installed Light Source only. All accessory Light Source

purchased separately are warranted for 90 days.

Who the warranty protects:

This warranty is valid only for the rst consumer purchaser.

What the warranty does not cover:

1. Any product on which the serial number has been defaced, modied or removed.

2. Damage, deterioration, failure, or malfunction resulting from:

a. Accident, abuse, misuse, neglect, re, water, lightning, or other acts of nature,

improper maintenance, unauthorized product modication, or failure to follow

instructions supplied with the product.

b. Operation outside of product specications.

c. Operation of the product for other than the normal intended use or not under

normal conditions.
d. Repair or attempted repair by anyone not authorized by ViewSonic.
e. Any damage of the product due to shipment.
f. Removal or installation of the product.

41

g. Causes external to the product, such as electric power uctuations or failure.
h. Use of supplies or parts not meeting ViewSonic’s specications.

i. Normal wear and tear.
j. Any other cause which does not relate to a product defect.

3. Removal, installation, and set-up service charges.

How to get service:

1. For information about receiving service under warranty, contact ViewSonic
Customer Support (please refer to “Customer Support” page). You will need to
provide your product’s serial number.

2. To obtain warranted service, you will be required to provide (a) the original dated
sales slip, (b) your name, (c) your address, (d) a description of the problem, and
(e) the serial number of the product.

3. Take or ship the product freight prepaid in the original container to an authorized
ViewSonic service center or ViewSonic.

4. For additional information or the name of the nearest ViewSonic service center,
contact ViewSonic.

Limitation of implied warranties:

There are no warranties, express or implied, which extend beyond the description

contained herein including the implied warranty of merchantability and tness for a

particular purpose.

Exclusion of damages:

ViewSonic’s liability is limited to the cost of repair or replacement of the product.
ViewSonic shall not be liable for:

1. Damage to other property caused by any defects in the product, damages based

upon inconvenience, loss of use of the product, loss of time, loss of prots, loss of

business opportunity, loss of goodwill, interference with business relationships, or
other commercial loss, even if advised of the possibility of such damages.

2. Any other damages, whether incidental, consequential or otherwise.

3. Any claim against the customer by any other party.

E󰀨ectoflocallaw:

This warranty gives you specic legal rights, and you may also have other rights

which vary from local authority. Some local governances do not allow limitations on
implied warranties and/or do not allow the exclusion of incidental or consequential
damages, so the above limitations and exclusions may not apply to you.

Sales outside the U.S.A. and Canada:

For warranty information and service on ViewSonic products sold outside of the
U.S.A. and Canada, contact ViewSonic or your local ViewSonic dealer.
The warranty period for this product in mainland China (Hong Kong, Macao and
Taiwan Excluded) is subject to the terms and conditions of the Maintenance
Guarantee Card.
For users in Europe and Russia, full details of warranty provided can be found in
www.viewsoniceurope.com under Support/Warranty Information.

Projector Warranty Term Template In UG
VSC_TEMP_2005

42

Mexico Limited Warranty

ViewSonic® Projector

What the warranty covers:

ViewSonic warrants its products to be free from defects in material and workmanship, under normal
use, during the warranty period. If a product proves to be defective in material or workmanship during
the warranty period, ViewSonic will, at its sole option, repair or replace the product with a like product.
Replacement product or parts may include remanufactured or refurbished parts or components &
accessories.

Howlongthewarrantyise󰀨ective:

ViewSonic’s standard warranty period is one (1) year for any product model in any country, unless

a longer warranty period is specied and provided by ViewSonic . Please refer to the ViewSonic

website in your country to check the local terms and model variants, and see if the product model in
your country is eligible for a longer warranty period.

Who the warranty protects:

This warranty is valid only for the rst consumer purchaser.

What the warranty does not cover:

1. Any product on which the serial number has been defaced, modied or removed.

2. Damage, deterioration or malfunction resulting from:

a. Accident, misuse, neglect, re, water, lightning, or other acts of nature, unauthorized product

modication, unauthorized attempted repair, or failure to follow instructions supplied with the

product.

b. Any damage of the product due to shipment.

c. Causes external to the product, such as electrical power uctuations or failure.
d. Use of supplies or parts not meeting ViewSonic’s specications.

e. Normal wear and tear.
f. Any other cause which does not relate to a product defect.

3. Any product exhibiting a condition commonly known as “image burn-in” which results when a static
image is displayed on the product for an extended period of time.

4. Removal, installation, insurance, and set-up service charges.

How to get service:

For information about receiving service under warranty, contact ViewSonic Customer Support (Please
refer to the attached Customer Support page). You will need to provide your product’s serial number,
so please record the product information in the space provided below on your purchase for your future
use. Please retain your receipt of proof of purchase to support your warranty claim.
For Your Records
Product Name: ________________________ Model Number: ____________________________
Document Number: ____________________ Serial Number: ____________________________
Purchase Date: ________________________ Extended Warranty Purchase? _____________(Y/N)
If so, what date does warranty expire? __________

1. To obtain warranty service, you will be required to provide (a) the original dated sales slip, (b) your
name, (c) your address, (d) a description of the problem, and (e) the serial number of the product.

2. Take or ship the product in the original container packaging to an authorized ViewSonic service
center.

3. Round trip transportation costs for in-warranty products will be paid by ViewSonic.

Limitation of implied warranties:

There are no warranties, express or implied, which extend beyond the description contained herein

including the implied warranty of merchantability and tness for a particular purpose.

Exclusion of damages:

ViewSonic’s liability is limited to the cost of repair or replacement of the product. ViewSonic shall not
be liable for:

1. Damage to other property caused by any defects in the product, damages based upon

inconvenience, loss of use of the product, loss of time, loss of prots, loss of business opportunity,

loss of goodwill, interference with business relationships, or other commercial loss, even if advised
of the possibility of such damages.

2. Any other damages, whether incidental, consequential or otherwise.

3. Any claim against the customer by any other party.

4. Repair or attempted repair by anyone not authorized by ViewSonic.

43

Contact Information for Sales & Authorized Service (Centro Autorizado de Servicio) within Mexico:

Name, address, of manufacturer and importers:

México, Av. de la Palma #8 Piso 2 Despacho 203, Corporativo Interpalmas,
Col. San Fernando Huixquilucan, Estado de México
Tel: [phone] http://www.viewsonic.com/la/soporte/index.htm

NÚMERO GRATIS DE ASISTENCIA TÉCNICA PARA TODO MÉXICO: 001.866.823.2004

Hermosillo:

Distribuciones y Servicios Computacionales SA de CV.
Calle Juarez 284 local 2
Col. Bugambilias C.P: 83140
Tel: [phone]
E-Mail: [e-mail]

Villahermosa:

Compumantenimietnos Garantizados, S.A. de C.V.
AV. GREGORIO MENDEZ #1504
COL, FLORIDA C.P. 86040
Tel: [phone]
E-Mail: [e-mail]

Puebla, Pue. (Matriz):

RENTA Y DATOS, S.A. DE C.V. Domicilio:
29 SUR 721 COL. LA PAZ
72160 PUEBLA, PUE.
Tel: [phone] CON 10 LINEAS
E-Mail: [e-mail]

Veracruz, Ver.:

CONEXION Y DESARROLLO, S.A DE C.V. Av. Americas # 419
ENTRE PINZÓN Y ALVARADO
Fracc. Reforma C.P. 91919
Tel: [phone]
E-Mail: [e-mail]

Chihuahua

Soluciones Globales en Computación
C. Magisterio # 3321 Col. Magisterial
Chihuahua, Chih.
Tel: [phone]
E-Mail: [e-mail]

Cuernavaca

Compusupport de Cuernavaca SA de CV
Francisco Leyva # 178 Col. Miguel Hidalgo
C.P. 62040, Cuernavaca Morelos
Tel: [phone]
E-Mail: [e-mail]

Distrito Federal:

QPLUS, S.A. de C.V.
Av. Coyoacán 931
Col. Del Valle 03100, México, D.F.
Tel: [phone]
E-Mail : [e-mail]

Guadalajara, Jal.:

SERVICRECE, S.A. de C.V.
Av. Niños Héroes # 2281
Col. Arcos Sur, Sector Juárez
44170, Guadalajara, Jalisco
Tel: [phone]
E-Mail: [e-mail]

Guerrero Acapulco

GS Computación (Grupo Sesicomp)
Progreso #6-A, Colo Centro
39300 Acapulco, Guerrero
Tel: [phone]

Monterrey:

Global Product Services
Mar Caribe # 1987, Esquina con Golfo Pérsico
Fracc. Bernardo Reyes, CP 64280
Monterrey N.L. México
Tel: [phone]
E-Mail: [e-mail]

MERIDA:

ELECTROSER
Av Reforma No. 403Gx39 y 41
Mérida, Yucatán, México CP97000
Tel: [phone]
E-Mail: [e-mail]

Oaxaca, Oax.:

CENTRO DE DISTRIBUCION Y
SERVICIO, S.A. de C.V.
Murguía # 708 P.A., Col. Centro, 68000, Oaxaca
Tel: [phone]
Fax: [phone]
E-Mail. [e-mail]

Tijuana:

STD
Av Ferrocarril Sonora #3780 L-C
Col 20 de Noviembre
Tijuana, Mexico

FOR USA SUPPORT:

ViewSonic Corporation
14035 Pipeline Ave. Chino, CA 91710, USA
Tel: [phone]
E-Mail: http://www.viewsonic.com

Projector Mexico Warranty Term Template In UG
VSC_TEMP_2006

44