ViewSonic LS625X, LS625W User Manual

LS625X/LS625W DLP Projector

User Guide

IMPORTANT: Please read this User Guide to obtain important information on installing and using your product in a safe manner, as well as registering your product for future service. Warranty information contained in this User Guide will describe your limited coverage from ViewSonic Corporation, which is also found on our web site at http://

www.viewsonic.com in English, or in specic languages using the Regional selection

box in the upper right corner of our website. “Antes de operar su equipo lea cu idadosamente las instrucciones en este manual”

Model No. VS17442/VS17443

Compliance Information

FCC Statement

This device complies with part 15 of FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

● Reorient or relocate the receiving antenna.

● Increase the separation between the equipment and receiver.

● Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

● Consult the dealer or an experienced radio/TV technician for help.

Warning: You are cautioned that changes or modications not expressly approved by

the party responsible for compliance could void your authority to operate the equipment.

For Canada

CAN ICES-3 (B)/NMB-3(B)

CE Conformity for European Countries

The device complies with the EMC Directive 2014/30/EU and Low Voltage Directive 2014/35/EU.

Following information is only for EU-member states:

The mark is in compliance with the Waste Electrical and Electronic Equipment Directive 2012/19/EU (WEEE).

The mark indicates the requirement NOT to dispose the equipment including any spent or discarded batteries or accumulators as unsorted municipal waste, but use the return and collection systems available.

If the batteries, accumulators and button cells included with this equipment, display the chemical symbol Hg, Cd, or Pb, then it means that the battery has a heavy metal content of more than 0.0005% Mercury or more than, 0.002% Cadmium, or more than 0.004% Lead.

Important Safety Instructions

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this unit near water.

6. Clean with a soft, dry cloth.

7. Do not block any ventilation openings. Install the unit in accordance with the manufacturer’s instructions.

8. Do not install near any heat sources such as radiators, heat registers, stoves, or

other devices (including ampliers) that produce heat.

9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade and the third outlet, consult an electrician for replacement of the obsolete outlet.

10. Protect the power cord from being walked on or pinched particularly at plugs. Convenience receptacles and the point where they exit from the unit. Be sure that the power outlet is located near the unit so that it is easily accessible.

11. Only use attachments/accessories specied by the manufacturer.

12. Use only with the cart, stand, tripod, bracket, or table specied by the manufacturer, or sold with the unit. When a cart is used, use caution when moving the cart/unit combination to avoid injury from tipping over.

13. Unplug this unit when unused for long periods of time.

14. Refer all servicing to qualied service personnel. Servicing is required when the unit has been damaged in any way, such as: if the power-supply cord or plug is damaged, if liquid is spilled onto or objects fall into the unit, if the unit is exposed to rain or moisture, or if the unit does not operate normally or has been dropped.

Declaration of RoHS2 Compliance

This product has been designed and manufactured in compliance with Directive 2011/65/EU of the European Parliament and the Council on restriction of the use of certain hazardous substances in electrical and electronic equipment (RoHS2 Directive) and is deemed to comply with the maximum concentration values issued by the European Technical Adaptation Committee (TAC) as shown below:

Substance Proposed Maximum

Concentration

Lead (Pb) 0.1% < 0.1% Mercury (Hg) 0.1% < 0.1% Cadmium (Cd) 0.01% < 0.01% Hexavalent Chromium (Cr6+) 0.1% < 0.1% Polybrominated biphenyls (PBB) 0.1% < 0.1% Polybrominated diphenyl ethers (PBDE) 0.1% < 0.1%

Actual Concentration

Certain components of products as stated above are exempted under the Annex III of the RoHS2 Directives as noted below:

Examples of exempted components are:

1. Lead in glass of cathode ray tubes.

2. Lead in glass of uorescent tubes not exceeding 0.2% by weight.

3. Lead as an alloying element in aluminium containing up to 0.4% lead by weight.

4. Copper alloy containing up to 4% lead by weight.

5. Lead in high melting temperature type solders (i.e. lead-based alloys containing 85% by weight or more lead).

6. Electrical and electronic components containing lead in a glass or ceramic other than dielectric ceramic in capacitors, e.g. piezoelectronic devices, or in a glass or ceramic matrix compound.

iii

Copyright © ViewSonic® Corporation, 2017. All rights reserved. Macintosh and Power Macintosh are registered trademarks of Apple Inc. Microsoft, Windows, Windows NT, and the Windows logo are registered trademarks of Microsoft Corporation in the United States and other countries. ViewSonic, the three birds logo, OnView, ViewMatch, and ViewMeter are registered trademarks of ViewSonic Corporation. VESA is a registered trademark of the Video Electronics Standards Association. DPMS and DDC are trademarks of VESA. PS/2, VGA and XGA are registered trademarks of International Business Machines Corporation. Disclaimer: ViewSonic Corporation shall not be liable for technical or editorial errors or omissions contained herein; nor for incidental or consequential damages resulting from furnishing this material, or the performance or use of this product. In the interest of continuing product improvement, ViewSonic Corporation reserves the

right to change product specications without notice, Information in this document may

change without notice. No part of this document may be copied, reproduced, or transmitted by any means, for any purpose without prior written permission from ViewSonic Corporation.

Product Registration

To fulll possible future product needs, and to receive additional product information as

it becomes available, please visit your region section on ViewSonic’s website to register your product online. Registering your product will best prepare you for future customer service needs.

Please print this user guide and ll the information in the “For Your Records” section. For additional information, please see the “Customer Support” section in this guide.

For Your Records

Product Name: LS625X/LS625W

ViewSonic DLP Projector

Model Number: VS17442/VS17443 Document Number: LS625X/LS625W_UG_ENG Rev.1A Serial Number: ________________________________________________ Purchase Date: ________________________________________________

Product disposal at end of product life

The lightsource in this product contains mercury which can be dangerous to you and the environment. Please use care and dispose of in accordance with local, state or federal laws. ViewSonic respects the environment and is committed to working and living green. Thank you for being part of Smarter, Greener Computing. Please visit ViewSonic website to learn more. USA & Canada: http://www.viewsonic.com/company/green/recycle-program/ Europe: http://www.viewsoniceurope.com/uk/support/recycling-information/ Taiwan: http://recycle.epa.gov.tw/recycle/index2.aspx

Table of Contents

Key safety instructions .... 1

Introduction .......................3

Projector features ...................................... 3

Shipping contents ...................................... 4

External appearance of the projector ........ 5

Device control and functions ..................... 6

Projector Positioning .....12

Choosing a location ................................. 12

Projection Dimension............................... 13

Connection ......................14

Connect to the computer or monitor ........ 15

Connecting to Video source devices ....... 16

Connecting to HDMI devices ................... 17

To connect the projector to a

Component Video source device: ............ 17

Changing HDMI input settings ................. 24

Adjusting the projected image ................. 25

Perform keystone correction.................... 26

Adjust four corners .................................. 26

Zoom in to see details ............................. 27

Selecting the aspect ratio ........................ 27

About the aspect ratio.............................. 28

Optimizing the image ............................... 29

Fine-tuning of image quality in

user modes .............................................. 30

Setting the Presentation Timer ................ 33

Hiding the image...................................... 34

Locking control keys ................................ 34

Light source settings................................ 34

Extending light source life........................ 35

Operations at high altitudes ..................... 36

Using the CEC function ........................... 36

3D functions............................................. 37

Connect to S-video signal source

device ...................................................... 17

Connecting to composite video source

devices .................................................... 18

Audio playback with the projector ............ 18

Operation .........................19

Activate the projector ............................... 19

Using the menus...................................... 19

Using the password function ................... 21

Setting a password .................................. 21

If you forget your password ..................... 21

Entering the password recall

procedure ................................................ 22

Change Password ................................... 22

Disabling the password function .............. 22

Control the projector through

the local area network ............................. 37

Control the projector with the

web browser ............................................ 38

About Crestron e-Control Using the projector under

standby mode .......................................... 43

Switch off the projector ............................ 44

Menu operations ...................................... 45

Description of each menu ........................ 48

® ........................................... 41

Maintenance ....................52

Care of the projector ................................ 52

LED Indicator ........................................... 53

Troubleshooting ............. 54

Switching input signal .............................. 23

Specications ................. 55

Projector specications............................ 55

Fuse specications .................................. 55

Dimensions .............................................. 56

Ceiling mount installation......................... 56

Timing chart ............................................. 57

Disclaimer ................................................ 61

Appendix .........................62

IR control table ........................................ 62

Address Code .......................................... 63

RS232 command table ............................ 64

Key safety instructions

Design and testing of your projector have been carried out in compliance with the latest safety standards for information technology (IT) devices. However, it is extremely important for you to follow the instructions provided in this manual and product labels during use to ensure user safety.

Safety Instructions

● Please read through this manual before using the projector. Save it for future

reference.

● Do not look straight at the projector lens during operation. The intense light

beam may damage your eyes.

● Refer servicing to qualied service personnel.

● Always open the lens shutter or remove the lens cap when the projector light source has been switched on.

● In some areas there may be line voltage instability. This projector is designed to operate safely within a mains voltage between 100 to 240 volts AC, but could fail if power cuts or surges of ±10 volts occur. In areas where the mains voltage may

uctuate or cut out, it is recommended that you connect your projector through a power stabilizer, surge protector or uninterruptible power supply (UPS).

● Do not block the projection lens with any objects when the projector is under operation as this could cause the objects to become heated and deformed or even

cause a re.

● Do not place the projector on an unstable cart, stand, or cable. The product may fall and sustain serious damages.

● Do not attempt to disassemble this projector. The projector contains high voltage parts that may cause electrocution or death when it comes in contact with the human body. Under no circumstances should you ever undo or remove any other covers.

Refer servicing to qualied service personnel.

● Do not place this projector in any of the following environments.

- Space that is poorly ventilated or conned. Allow at least 50 cm clearance from

walls and ensure free ow of air around the projector.

- Locations where temperatures may become excessively high, such as the inside of a car with all windows rolled up.

- Locations that are too humid, dusty, or smoky may contaminate optical components, shortening the projector's life span and darkening the image.

- Locations near re alarms

- Locations where temperature exceed 35°C/95°F.

- Locations with altitudes greater than 5000 m (16500 feet).

● Do not block the ventilation holes. If the ventilation holes are seriously obstructed,

overheating inside the projector may result in a re.

- Do not place this projector on a blanket, bedding or any other soft surface.

- Do not cover this projector with a cloth or any other item.

- Do not place inammables near the projector.

● Do not step on the projector or place any objects upon it. These acts may damage the projector itself as well as cause accidents or personal injury.

● Do not place liquids near or on the projector. Liquids spilled into the projector may cause damage. If the projector does become wet, please unplug the power cable from the power socket and contact your local repair center for repairs.

● This product can be mounted on a ceiling suspension mount for back projection.

Use only ceiling suspension mounts that meet the relevant requirements and ensure that

the installation is safe.

● When the projector is under operation, you may sense some heated air and odor from its ventilation grill. It is a normal phenomenon and not a product defect.

● Do not use the safety lever during transport or installation purposes. The safety lever should only be used with the anti-theft cables sold on the market.

Safety instructions for ceiling mounting of the projector

We hope you to have a pleasant user experience with our projector. This is why we’re bringing these safety reminders to your attention to prevent possible damage to person and property.

If you intend to mount your projector on the ceiling, we strongly recommend that you use a suitable projector ceiling mount kit and ensure it is securely and safely installed.

There may be safety risks if you fail to use an appropriate projector ceiling mounting kit.

Use of inappropriate connectors or screws of the wrong specications or length may cause

the projector to fall from the ceiling. You can purchase a projector ceiling mounting kit from the projector dealer. We

recommend buying a safety harness in addition to the mounting kit. The harness should be securely connected to the anti-theft locking groove on the projector as well as the base of the ceiling mounting support. This will provide additional protection in case the connectors of the mounting support becoming loose.

Like handling any bright light sources, do not directly look at the

light beam.

Introduction

Projector features

The projector integrates high-performance optical engine projection and a user-friendly design to deliver high reliability and ease of use. The projector offers the following features.

The projector offers the following features.

● The color mode provides different options designed for different projectors.

● Compatible with NTSC, PAL, SECAM and HDTV

● D-Sub 15-pin terminal can be connected to analog video

● Equipped with HDMI connection, supports HDCP (PA501S with no such features)

● Multi-language On-Screen Display (OSD) menus

● Digital keystone correction to correct distorted images

● RS-232 interface supports serial control

● The power saving mode reduces the lamp power consumption by up to 30% when no input signal is detected for a set length of time.

● Presentation timer for better control of time during presentations

● 3D Ready supported

● Select Fast Shutdown

● Color management can be used to adjust the color according to your preferences

● The screen type correction function can be projected on a variety of pre-set color surfaces

● Switching among Normal, Power Saving and CUSTOM Modes reduces power consumption.

● Quick Auto Search speeding up the signal detecting process

● Activating Power Saving mode will bring power consumption to below 0.5W

● “Network Settings” allows management on the projector state by using a remote computer.

● One-key auto-adjustment to display the best picture quality (applicable to the analog signal only)

● Provides Color Management adjustments for digital / video displays

Shipping contents

Carefully unpack the product and check that you have all of the items shown below. If any of these items are missing, please contact your place of purchase.

Standard accessories

The supplied accessories will be suitable for your region, and may differ from those illustrated.

Projector Power cord

On Off

HDMI 1 HDMI 2COMP

Auto

Source

Sync

Freeze Blank

PatternAspect

PgUp

PgDn

Color

Network

Mode

VGA cable Remote control battery Quick Start Guide

External appearance of the projector

Front/Rear

Side

Top

LS625X LS625W

Bottom

Warning

● This equipment must be connected to ground.

● You may add power interruption devices in the xed wiring or plug in the power cable to a nearby socket for convenience. If failures or errors occur during equipment operations, use the power interruption device to cut

the power or unplug the power cable from the socket.

Device control and functions



Projector

LS625W LS625X

Turn the projector power on or off.

2. (Power LED indicator)

Please refer to “LED indicator message”.

3. (TEMP LED indicator)

Please refer to “LED indicator message”.

4. (LAMP LED indicator)

Please refer to “LED indicator message”.

5. / / / (Keystone button)

Manually corrects distorted images resulting from an angled projection.

Left/Right/Up/Down (Navigation button)



Selects the required menu item to make adjustments.

6. ENTER

Enter the selected on-screen display (OSD) menu item.

SOURCE

A source selection bar displays.

7. MENU/EXIT

MENU: Displays or exits the on-screen display menu. EXIT: Returns the previous OSD menu, exits and saves the menu settings.

Left/Right (direction buttons): Selects the required menu item to make

adjustments.

: Adjusts the projector’s sound level.

Up/Down (direction buttons): Selects the required menu item to make

adjustments.

/ (Keystone button): Manually corrects distorted images resulting from an angled

projection.

Remote control

On Of f

HDMI 1 HDMI 2COMP

Aut o Sync

Source

16 17 18

4 4

6 7 8

9 10 11

12 13 14

1. On

Turn on the projector.

COMP

Select the D-Sub / component display.

3. Auto Sync

Automatically verify the best picture quality for the displayed image.

Keystone button and direction button

/ / /

Manually corrects distorted images resulting from an angled projection.

Left/Right/Up/Down



Selects the required menu item to make adjustments.

(Laser)

Emits a visible laser pointer beam which can be used during presentations.

Open the OSD menu.

Freeze

Freezes the projected image.

Aspect

Selects the display aspect ratio.

Freeze Blank

PgUp

PgDn

Colo r Mod e

PatternAspect

22 23 24

Network

9. 10. PgUp/PgDn

Connect the projector to a computer with a Mini USB cable to operate the display software (Microsoft PowerPoint) running on a connected computer.When the cursor mode is activated, these buttons will reference the previous and next functions.

11. (Volume)

Decrease the volume.

12. (Presentation Timer)

Brings up the Presentation Timer settings menu.

13. Eco Mode

Displays the Lamp Mode option list.

14.

(Mute)

Toggles the projector audio between on and off.

15.

Oﬀ

Turn the projector over.

16. 17. HDMI 2/HDMI 1

Select the source of the displayed HDMI.

18. SOURCE

A source selection bar displays.

19.

ENTER

Enter the selected screen to display (OSD) menu item.

20.

EXIT

Return to the previous OSD menu to exit and save the menu settings.

21. Pattern

Shows the inbuilt testing screens.

22.

Blank

Hide screen image.

23. (Zoom out)

The displayed zoom lever can be used to zoom out the projected image

Use the laser pointer. The laser pointer is a professional tool for supporting presentations. Press this button

to emit a colored laser pointer beam. The laser beam emitted is within the visible spectrum. To generate the pointer beam continuously, press and hold the [Laser] button.

24. (Volume+)

Increase the volume.

25. (Zoom in)

The displayed zoom lever can be used to zoom in the projected image

26.

Displays the projector’s internal information.

27.

Network

Network settings.

28.

Color Mode

Select Color Mode.

Do not look at the laser light and do not aim the laser beam at yourself or other people. Please read the warning texts provided at the back of the remote control before use.

The laser pointer is not a toy. Parents should be aware of the hazards posed by laser energy and place the remote at a location not accessible to children.

Remote control code

The projector is capable of having 8 different remote control codes (1 to 8). When using multiple projectors close to each other at the same time, switching the remote control codes will prevent projector disruption by other remote controls. First set the projector’s remote control code then switch the code of the remote control itself.

If you want to switch the code at the projector end, please go to System: Remote Control Code menu and select 1 to 8.

If you want to switch the code at the remote control end, please press and hold both the [ID set] and number key corresponding to the remote control code for at least 5

On Off

HDMI 1 HDMI 2COMP

Auto Sync

Source

PgUp

seconds. 1 is the initial code by default. Setting the code to 8 allows the remote control to control every projector.

Freeze Blank

PatternAspect

PgUp

PgDn

Color

Network

Mode

The projector will not respond to commands issued by the remote control commands if the projector and remote control codes are not the same. When this happens, a message will appear to remind you to switch the remote control code.

Remote control setting

Remote control code

PgDn

Colo r Mod e

Network

Using the remote control cursor

Use the remote control to operate your computer during presentations for greater exibility.

1. Before using the remote control to replace your cursor, x one end of the USB cable to the projector Mini USB port and the other end to the PC or notebook computer. See “Connect to the computer” for details.

2. Change the input signal to D-Sub or HDMI via PC source.

3. To use the software displayed on the connected computer (such as Microsoft PowerPoint), go to the previous or next page by pressing the previous page / next page.

Remote control effective range

There is an infra-red (IR) remote control sensor located at the back of the projector. Hold the remote control and maintain a perpendicular angle within 30 degrees with the IR remote control sensor to achieve normal remote control functions. The distance between the remote control and the sensor should not exceed 8 meters (about 26 feet).

Do not place any obstruction in front of the IR sensor on the projector as this may block the IR beam.

Approx. 30°

Note

●

When the intense light source such as sunlight or uorescent light is used to illuminate the remote sensor, the remote control may not work.

●

Operate the remote control where you can see the remote sensor.

●

Do not shake or drop the remote control.

●

Store the remote control in a cool, dry place.

●

Do not spill water on the remote control or place moist objects on it.

●

Do not disassemble the remote control.

Replacing the remote control battery

1. To open the battery cover, place the remote control with the backside facing upwards. Press down at the indicated area and then pull the battery lid upwards along the indicated direction.

2. Take out the old batteries (if required) and then place 2 AAA batteries according to the indicated orientation. The positive pole of the battery should be directed at the (+) direction while the negative pole should be directed at the direction.

3. Align the battery cover with the bottom of the remote control and return the cover to its original position to complete the process.

Open the battery cover as

shown in the illustration.

Install the battery as shown

in the illustration.

Cover the battery cover.

Warning

● Avoid keeping the remote control and battery in moist or hot places, such as the kitchen, bathroom, sauna, solarium or car.

● Replace only with the same or equivalent type recommended by the battery manufacturer.

● Refer to the manufacturer’s instructions and local environmental regulations to dispose of old batteries.

● Do not throw batteries into res. There may be danger of an explosion.

● If the battery is at or if you will not be using the remote control for a while, remove the battery to prevent

battery leaks from damaging the remote control.

Projector Positioning

Choosing a location

You may refer to the room layout or personal preference to determine the location of installation. Considerations include size and position of the screen, location of a suitable power outlet, as well as the location and distance between the projector and other equipment.

There are 4 potential installation locations for the projector:

1. Front Table

For this location, the projector is placed right in front of the screen. This is the most commonly employed means for placing the projector. It is quick to setup and highly mobile.

After turning on the projector, go to System:

Projector Position menu and select Front Table.

2. Front Ceiling

For this location, the projector is suspended upside-down from the ceiling in front of the screen.

Purchase a Projector Ceiling Mounting Kit from your dealer to mount your projector on the ceiling.

After turning on the projector, go to System:

Projector Position menu and select Front Ceiling.

3. Rear Ceiling

For this location, the projector is suspended upside-down from the ceiling behind the screen.

Note that a special rear projection screen and Projector Ceiling Mounting Kit are required for this installation location.

After turning on the projector, go to System:

Projector Position menu and select Rear Ceiling.

4. Rear Table

For this location, the projector is placed right behind the screen.

Note that a special rear projection screen is required. After turning on the projector, go to System:

Projector Position menu and select Rear Table.

Projection Dimension

(a)

(c)

(b)

(e)

(f)

(d)

(a)

(c)

(b)

(e)

(f)

(d)

Refer to the chart below to determine the screen size and projection distance.

(E): Screen (f): lens center

LS625X

(a) Screen size

[inch (m)]

Displays an image in 4:3 size on the 4:3

screen

(b) Projection

distance

[m (inch)]

height

[cm (inch)]

(d) Vertical

offset

[cm (inch)]

Displays an image in 4:3 size on the 16:9

screen

(b) Projection

distance

[m (inch)]

height

[cm (inch)]

(d) Vertical

[cm (inch)]

60 (1.5) 0.6 (24) 91 (36) 8.2 (3.2) 0.6 (24) 69 (27) 19.6 (7.7) 70 (1.8) 0.7 (28) 107 (42) 9.5 (3.8) 0.7 (28) 80 (31.5) 22.9 (9.0) 80 (2.0) 0.8 (31) 122 (48) 10.9 (4.3) 0.8 (31) 91 (36) 26.2 (10.3)

90 (2.3) 0.9 (35) 137 (54) 12.3 (4.8) 0.9 (35) 103 (40.5) 29.4 (11.6) 100 (2.5) 1.0 (39) 152 (60) 13.6 (5.4) 1.0 (39) 114 (45) 32.7 (12.9) 120 (3.0) 1.2 (47) 183 (72) 16.4 (6.4) 1.2 (47) 137 (54) 39.2 (15.4) 150 (3.8) 1.5 (59) 229 (90) 20.5 (8.1) 1.5 (59) 171 (67.5) 49.0 (19.3) 200 (5.1) 2.0 (79) 305 (120) 27.3 (10.7) 2.0 (79) 229 (90) 65.4 (25.7) 250 (6.4) 2.5 (98) 381 (150) 34.1 (13.4) 2.5 (98) 286 (112.5) 81.7 (32.2) 300 (7.6) 3.0 (118) 457 (180) 40.9 (16.1) 3.0 (118) 343 (135) 98.1 (38.6)

LS625W

Displays an image in 16:10 size on the

(a) Screen size

[inch (m)]

(b) Projection

distance

[m (inch)]

16:10 screen

height

[cm (inch)]

(d) Vertical

offset

[cm (inch)]

60 (1.5) 0.67 (26) 81 (31.8) 5.3 (2.1) 0.6 (24) 73 (28.6) 9.4 (3.7)

70 (1.8) 0.79 (31) 94 (37.1) 6.2 (2.4) 0.7 (28) 85 (33.4) 10.9 (4.3)

80 (2.0) 0.91 (36) 108 (42.4) 7.1 (2.8) 0.8 (31) 97 (38.2) 12.5 (4.9)

90 (2.3) 1.03 (40) 121 (47.7) 8.0 (3.1) 0.9 (35) 109 (42.9) 14.1 (5.5) 100 (2.5) 1.14 (45) 135 (53) 8.9 (3.5) 1.0 (39) 121 (47.7) 15.6 (6.2) 120 (3.0) 1.38 (54) 162 (63.6) 10.7 (4.2) 1.2 (47) 145 (57.2) 18.8 (7.4) 150 (3.8) 1.73 (68) 202 (79.5) 13.3 (5.2) 1.5 (59) 182 (71.5) 23.4 (9.2) 200 (5.1) 2.32 (91) 269 (106) 17.8 (7.0) 2.0 (79) 242 (95.4) 31.3 (12.3) 250 (6.4) 2.91 (115) 337 (132.5) 22.2 (8.7) 2.5 (98) 303 (119.3) 39.1 (15.4) 300 (7.6) 3.50 (138) 404 (159) 26.7 (10.5) 3.0 (118) 363 (143.1) 46.9 (18.5)

Displays an image in 16:10 size on the

16:9 screen

(b) Projection

distance

[m (inch)]

height

[cm (inch)]

(d) Vertical

[cm (inch)]

offset

There is 3% tolerance among these numbers due to optical component variations. It is recommended that if you intend to permanently install the projector, you should physically test

the projection size and distance using the actual projector in situ before you permanently install it, so as to make allowance for this projector’s optical characteristics. This will help you determine the exact mounting position so that it best suits your installation location.

Connection

When connecting a signal source to the projector, be sure to:

1. Turn all devices off before making any connections.

2. Use the correct signal cables for each source.

3. Ensure the cables are rmly inserted.

In the connections shown below, some cables may not be included within the projector packaging (please refer to “Shipping contents”). You may purchase the required signal cables from an electronics store.

The following links and icons are for references only. Connection jacks at the back of the projectors may differ according to the projector model.

Screen

Computer

HDMI

LAN interface

AV device

USB

RS232

S-VIDEO

4 5 6 7 8

USB charger

1. HDMI cable

2. USB cable (mini-B to type A)

3. RS-232 cable

4. VGA cable (D-Sub to D-Sub)

5. S-VIDEO cable

Internet

Monitor

Speaker

6. Audio Cable

7. Composite video line

8. VGA (D-Sub) to HDTV (RCA) line

9. RJ45 cable

Connect to the computer or monitor

Connect to the computer

1. Use the VGA cable provided. Plug one end to the D-Sub output jack at the computer end.

2. Connect the other end of the VGA cable to the COMPUTER signal input jack on the projector.

Many notebooks have not activated their monitor jack after being connected to the monitor. The user can often press FN + F3 or CRT/LCD button to switch ON/OFF the externally connected monitor. Find the function key labeled with the CRT/LCD or monitor icon on the notebook. Press the FN key and the labeled function key. Please refer to the instruction manual provided with the notebook computer for the combination keys and their functions.

Connect to the monitor

If you want the display to be shown both on the computer monitor as well as the screen, refer to the following instructions. Connect the VGA cable to the COMPUTER OUT signal output jack on the projector as well as the external display.

1. Connect the projector to the computer as described in the “Connect to the computer” section. Use a suitable VGA cable (only 1 such cable is provided) and connect one end of the cable to the D-Sub input jack on the video display.

2. If the display is provided with a DVI input jack, then connect the DVI end of the VGADVI-A cable to the DVI input jack on the video display.

3. Connect the other end of the cable to the COMPUTER OUT jack on the projector.

The MONITOR OUT output is only available when the COMPUTER 1 is connected to the projector in the standby mode. To use this connection mode, open the Power Management > Active VGA Out function in the Standby Settings menu.

Connecting to Video source devices

You can connect the projector to any of the following video source device with an output jack:

• HDMI (PA501S does not have this interface)

• Component Video

• S-Video

• Video (composite video)

Only 1 of the aforementioned connection methods is required to connect the projector to the video source device. However, different connection methods would provide a different video quality. The connection method selected would be determined by the presence of matching jacks on the projector and Video source device:

Best video quality

HDMI is the best video connection method available. If the source device comes with HDMI jacks, you will be able to acquire uncompressed digital video quality.

Please refer to “Connecting to HDMI devices” for details on how to connect the projector to HDMI devices.

If you don’t have any usable HDMI source, the next best video signal would be Component Video (not to be confused with Composite Video). Digital TV tuners and DVD players are provided with Component Video output sockets. If your device includes Component Video, then this would be your primary choice of connection to the (composite) video.

Please refer to “To connect the projector to a Component Video source device:” for details on how to connect your projector to Component Video devices.

Better video quality

S-video method provides slightly better simulation video compared to standard composite videos.If the video device is provided with both composite video and s-video output jacks,

you should try to choose S-video connection rst.

Please refer to “Connect to S-video signal source device” for details on how to connect your projector to S-video devices.

Least video quality

Composite Video is an analog video and will result in a perfectly acceptable, but less than optimal result from your projector, being the least video quality of the available methods described here.

Please refer to “Connecting to composite video source devices” for details on how to connect your projector to composite video devices.

Connecting audio

You can use the speaker of the projector in the presentation or connect other individual speaker to the audio output jack of the projector. Audio output is controlled by the volume and mute setup of the projector.

Connecting to HDMI devices

Use an HDMI cable to establish a connection between the projector and HDMI device.

1. Connect one end of the HDMI cable to the HDMI output jack on the video device.

2. Connect the other end of the cable to the HDMI signal input jack on the projector.

In the unlikely event that the projector is connected to a DVD player via the projector’s HDMI input and the projected picture displays wrong colors, please change the color space to YUV. See “Changing HDMI input settings” for details.

To connect the projector to a Component Video source device:

Examine your Video source device to determine if a set of unused Component Video output sockets is available:

• If so, you can continue with this procedure.

• If not, you will need to reassess which method to use to connect to the device.

1. Take a VGA (D-Sub) Component adapter cable and connect the end with 3 RCA type connectors to the Component Video output sockets of the Video source device. Match the color of the plugs to the color of the sockets; green to green, blue to blue, and red to red.

2. Connect the end of the VGA (D-Sub) Component adapter cable (with the D-Sub type connector) to the COMPUTER 1 or COMPUTER 2 jack on the projector.

If the selected video image is not displayed after the projector is turned on and the correct video source has been selected, check that the Video source device is turned on and operating correctly. You must also check that the signal cables have been connected correctly.

Connect to S-video signal source device

Examine your Video source device to determine if an unused S-Video output socket is available:

• If so, you can continue with this procedure.

• If not, you will need to reassess which method to use to connect to the device.

1. Take an S-Video cable and connect one end to the S-Video output socket of the Video source device.

2. Connect the other end of the S-Video cable to the S-VIDEO socket on the projector.

If you have already made a Component Video connection between the projector and this S-Video source device using Component Video connections, an S-Video connection will not be required as this is an unnecessary second connection of poorer picture quality. For more details, please refer to “Connecting to Video source devices”.

Connecting to composite video source devices

Examine your Video source device to determine if an unused composite output jack is available:

• If so, you can continue with this procedure.

• If not, you will need to reassess which method to use to connect to the device.

1. Take a Video cable and connect one end to the composite Video output socket of the Video source device.

2. Connect the other end of the video cable to the VIDEO socket on the projector.

When the component video is not available, use the composite video connection method to connect to this device. See “Connecting to Video source devices” for details.

Audio playback with the projector

You can use the speaker of the projector in the presentation or connect other individual speaker to the AUDIO OUT jack of the projector.

Operation

Activate the projector

Plug the power cord into the projector and into a wall socket. Turn on the switch on the wall socket (if available).

Press Power to switch on the projector.

If this is the rst time that you've switched on the projector, please refer to on-screen instructions and select your OSD language.

Switch on all connected equipment.

The projector will then begin a search of the input signals. The lower right corner of the

screen will display the current input signal being scanned. If the projector fails to detect a valid signal, the screen will display a [NO SIGNAL] message until an input signal is found.

You can press "Source" to select the input signal required. See “Switching input signal” for

details.

If the input signal frequency / resolution is outside the operating range of the projector, the blank screen will display the [Out of Range] message. Please change to an input signal which is compatible with the projector's resolution or set the input signal to a lower setting. For more details, please refer to the [Resolution Table].

Using the menus

This projector has an on-screen display (OSD) menu function that allows you to

change different settings.

The following OSD screenshot is for reference only. Actual OSD design may differ.

The following is an overview of the OSD menu.

Select

Sub-menu

Main menu

icon

Status

Press “MENU”

to go back to the previous window or to exit.

1. Press Menu and then press the remote control / to select the Display and press  to select the aspect ratio.

2. Press Menu and then press the

remote control / to select Image and press  to select the Color Mode.

3. Press Menu and then press the

remote control / to select Power Management and press  to select

the Auto Power On.

5. Press Menu and then press the remote control / to select Advanced and press  to select the

3D Settings.

4. Press Menu and then press the

remote control / to select Basic and press  to select the Audio

Settings.

6. Press Menu and then press the

remote control / to select System and press  to select the Language.

Using the password function

For security purposes and to help prevent unauthorized use, the projector includes an option for setting up password security. Passwords may be set using the On-Screen Display (OSD) menu. Please refer to the [Using the menus] section for details on OSD menu operations.

It is troublesome if you keep forgetting the password after setting up password protection. We recommend writing down the password and placing it somewhere safe for future reference in case you forget.

Setting a password

Once a password has been set, the user must provide the correct password after starting the projector. Otherwise, the projector cannot be used.

1. Open the OSD Menu and enter System > Security Settings menu.

2. Press [Enter]. The Security Settings page will be displayed.

3. Select Power On Lock, then press / and select ON.

4. The picture on the right shows 4 arrow keys (, , , ) which each represent 4 numbers (1, 2, 3, 4)

respectively. According to the password you desire to set, press the arrow keys to enter six digits for the

password.

5. Enter the password and conrm that password.

After completing password settings, the OSD menu will return to the Security Settings page.

6. Press [Exit] to leave the OSD menu.

If you forget your password

If the password function is activated, you will be asked to enter the six-digit password every time you turn on the projector. If you enter the wrong password, the password error message as pictured to the right will be displayed for 5 seconds before the message [INPUT PASSWORD] is shown. You can enter another 6-digit password. You may use the password recall procedure if you forgot your password and did not record it in this manual. See “Entering the password recall procedure” for details.

If you enter an incorrect password 5 times in succession, the projector will automatically shut down in a short time.

Entering the password recall procedure

1. Press and hold the [Auto Sync] button on the remote control for 3 seconds.

2. Write down the number and turn off your projector.

3. Seek help from the local service center to decode

the number. You may be required to provide proof of purchase to verify that you are an authorized user of

the projector.

The [XXX] number in the screenshot shown above is determined by the projector model number.

Change Password

1. Open the OSD and enter System > Security Settings > Change Password menu.

2. Press [Enter]. The message [INPUT CURRENT PASSWORD] will be shown.

3. Enter the old password.

● If the password entered is correct, another message [INPUT NEW PASSWORD]

will be shown.

● If the password entered is incorrect, then the password error message will

be displayed for 5 seconds before the screen shows the [INPUT CURRENT PASSWORD]. You will then need to re-enter the password. You can either press

[Exit] to cancel the process or try other passwords.

4. Enter a new password.

5. You have successfully assigned a new password to the projector. Remember to enter

the new password next time the projector is started.

6. Press [Exit] to leave the OSD menu.

Any digit entered will be displayed as asterisks [*] on-screen. We recommend writing down the password and placing it somewhere safe for future reference in case you forget.

Disabling the password function

1. Open the OSD menu and enter System > Security Settings > Power On Lock menu.

2. Press / and select OFF.

Though the password function is disabled, you need to keep the old password in hand should you ever need to re-activate the password function by entering the old password.

Switching input signal

The projector can be connected to multiple devices at the same time. However, it can only display one full screen at a time.

If you want the projector to automatically search for various signals, please conrm that the Quick Auto

Search function in the SYSTEM menu is switched ON.

You may also press the source selection button on the remote control or search for available input signals to manually select the desired signals.

1. Press [Source] to display the source selection column.

2. Keep pressing the / until you arrive at the desired signal, then press [Enter].

Once detected, the selected source information will display on the screen for seconds. If there are multiple devices connected to the projector, repeat steps 1 to 2

to search for another signal.

For display resolutions of this projector, please refer to “Projector specications”. To achieve the best image display effects, you should select and use an input signal that outputs at this resolution. Any other resolutions will be scaled by the projector depending upon the aspect ratio setting, which may cause some image distortion or loss of picture clarity. See

“Selecting the aspect ratio” for details.

Changing HDMI input settings

In the unlikely event that you connect the projector to a device (such as DVD or Bluray player) via the projector’s HDMI input jack, and the projected picture displays the wrong colors, please change the color space settings to one that complies with

the color space settings of the output device.

To perform this operation:

1. Open the OSD menu and enter ADVANCED > HDMI settings menu.

2. Press [Enter].

3. Select HDMI format, then press / to select a suitable color space according to the color space settings of the output device.

● RGB: Changes the color space to RGB.

● YUV: Changes the color space to YUV.

● Auto: Sets the projector to automatically detect the color space settings of the

color space.

4. Select HDMI Range, then press / to select a suitable color range according to the color range settings of the output device.

● Enhanced: Changes HDMI color range to 0-255.

● Normal: Changes HDMI color range to 16-235.

● Auto: Sets the projector to automatically detect the HDMI range of the input signal.

This function is only available when the HDMI input jack is being used.

Please refer to equipment documentation to gain more details on color space and HDMI range settings.

Adjusting the projected image

LS625X LS625W

Adjusting the projection angle

The projector is furnished with an adjustment support peg. The adjustment support peg may be used to

adjust projection height and projection angle along the

vertical axis. The user may turn the adjustment support peg to make ne adjustments to projection angle and position of the projected image until it reaches the

desired location.

If the projector is placed on an uneven surface or where the screen and projector

are not perpendicular to each other, the projected image may be subject to keystone (trapezoidal) distortion. For more details on projection calibration, please refer to

“Perform keystone correction”.

Lift and adjust the feet

Auto-adjustments to the image

The focus ring can be used to adjust the image clarity.

Focus ring

1. Sharpen the image by rotating the focus ring. It is recommended to use still images for focusing.

Perform keystone correction



Keystone distortion is a problem where the projected image becomes trapezoidal in shape (keystone distortion) as a result of poor projection angle.

To correct this situation, you should adjust projector height and use the following steps to correct the issue manually.

● Using the remote control

1. Press / to display the Keystone Correction page.

2. Press to initiate Keystone Correction at the

top of the image. Press to initiate Keystone Correction at the bottom of the image.

3. Press to initiate Keystone Correction at the left of the image. Press to initiate Keystone Correction at the right of the image.

● Using the OSD menu

1. Open the OSD menu and open Display > Keystone menu.

2. Press [Enter]. This will bring up the Keystone page.

Press /

3. Press to initiate Keystone Correction at the top of the image. Press to initiate

Keystone Correction at the bottom of the image.

4. Press to initiate Keystone Correction at the bottom of the image. Press to initiate Keystone Correction at the right of the image.

LS625X does not have the / keystone correction function.

Adjust four corners

Using the OSD menu Open the OSD menu and go to the Display > Corner Adj..

1. Display four corner adjustment OSD on the screen.

2. Select the corner to be adjusted and then the selected area will become gray.

3. Two corners can be adjusted.

4. Save the settings and then close the OSD menu.

How to reset the corner adjustment:

● Press “Enter” to reset the adjustments. “Resetting statement: Do you want to reset?

Reset/Cancel” will display on the screen.

● The corner adjustment will be reset if you adjust the Keystone.

LS625X does not have the corner adjusting function.

Zoom in to see details

You may need to expand the image to inspect details in the projected image. Use the arrow keys to move the images.

● Using the remote control

1. Press the on the remote to bring up the Zoom Bar.

2. Press  repeatedly to expand the image to the desired dimension.

3. To browse the image, press [Enter] to switch to displacement mode and use the

arrow keys (, , , ) to move the image for browsing.

4. To zoom out the image, press the zoom out key to zoom out the image size. You can also press the [Auto Sync] button on the remote control to restore the image to its original size.

● This function is suitable for remote control operations.

You can check the image only after zooming in. You can further zoom in to check the details. Adjustable range depends on different aspect ratios.

Selecting the aspect ratio

The 'aspect ratio' is the ratio of the image width to the image height. Most analog TV and computers have a 4:3 aspect ratio, while digital TV and DVDs have 16:9 aspect ratios. With the advent of digital signal processing, digital display devices like this projector can dynamically stretch and scale the image output to a different aspect than that of the image input signal. To change the projected image ratio (no matter what aspect the source is):

1. Open the OSD Menu and enter Display > Aspect ratio menu.

2. Press / to select an aspect ratio that suits the format of the video signal and your

display requirements.

About the aspect ratio

Choose how to make the screen suitable for the screen:

1. Auto: Proportional scaling of an image to t the

projector’s natural resolution in its horizontal width. This is suitable where the incoming image is neither in 4:3 nor 16:9 aspect ratios but where you want to make most use of the screen without altering the image’s aspect

ratio.

2. 4:3: Scales a picture so that it is displayed in the

center of the screen with a 4:3 aspect ratio. This is most suitable for 4:3 pictures such as those for computer monitors, standard denition TV, and 4:3 aspect DVD movies as these can be displayed without aspect

alteration.

3. 16:9: Scales a picture so that it is displayed in

the center of the screen with a 16:9 aspect ratio. This is most suitable for images which are already in a 16:9 aspect such as high denition TV because as these can be displayed without aspect alteration.

Image 16:10

Image 16:9

Image 4:3

Image 16:9

4. 16:10: Scales an image in ratio so that it is

displayed in the center of the screen with a 16:10 aspect ratio. This is most suitable for images which are already in a 16:10 aspect

Image 16:10

as it displays them with out aspect alteration.

5. Native: The image is projected as its original resolution, and resized to t within

the display area. For input signals with lower resolutions, the projected image will display smaller than if resized to full screen.

LS625X does not have the 16:10 aspect ratio function.

Optimizing the image

Selecting a picture mode

The projector is preset with several predened picture modes. You may choose one of these modes that best ts your operating environment and input signal picture type.

To select an operation mode that suits your need, please follow the steps described

below.

●Press [Color Mode] repeatedly until you arrive at the mode you desire.

●Enter Image > Color mode menu and press / to select the required mode.

Picture modes for different types of signals

The following lists the Picture modes that can be used for different signal types.

1. Standard mode: Suitable for normal conditions during the daytime environment.

2. Photo mode: Suitable for viewing photo mode.

3. Movie Mode: Applicable for playing colored movies, video clips from digital cameras,

or DVs from a PC input in darker (dim) environments to achieve the best viewing

effects.

4. Brightest: Maximizes the brightness of the projected image. This mode is suitable

when using projectors in environments such as well-lit rooms where extra-high brightness is required.

5. Presentation mode: Used during daytime presentations to match PC and laptop tint.

Fine-tuning of image quality in user modes

You may use several user-dened functions if the projector detects certain signal types. You can make adjustments to these functions based on your needs.

Adjusting Brightness

Enter Image > Brightness menu and then press

/.

The higher the value, the brighter the image. And lower the setting, darker the image.

Adjusting this control allows the black area of the image to appear just as black to

reveal details within.

Adjusting Contrast

Enter Image > Contrast menu and then press /. The higher the value, the greater the contrast. After

adjusting Contrast, this function may be used to set the peak-white level that matches the input signal and observed environment of your choice.

Adjusting Color

Enter Image > Advanced > Color menu and press /. Lower settings produce less color saturation. If the setting is too high, colors on the

image will be overpowering, which makes the image unrealistic.

This function is only available when the input signals are Video, YPbPr or YCbCr.

Adjusting Tint

Enter Image > Advanced > Tint menu and press /. The higher the value, the more reddish the picture becomes. The lower the value, the

more greenish the picture becomes.

This function is only available when the input signal is Video.

Adjusting Sharpness

Enter Image > Advanced > Sharpness menu and then press /. Higher settings produce sharper images. The lower the value, the softer the picture

becomes.

This function is only available when the input signals are Video, YPbPr or YCbCr.

Adjusting Brilliant Color

Enter Image > Advanced > Brilliant Color menu and press /. This feature utilizes a new color-processing algorithm and system level enhancements to

enable higher brightness while providing truer, more vibrant colors of the projected image. Brightness levels of mid-tone areas commonly seen in videos and natural landscapes are increased by more than 50%, allowing the projector to generate images in realistic and true colors. To acquire this quality of images, please select the level you desire. If not required, set this option to OFF.

Reducing image noise

Enter Image > Advanced > Noise Reduction menu, and then press /. This function is capable of reducing image noise generated electrically by different media

players. Higher settings will provide lower image noise.

This function is only available when PC, Video input signals were selected.

Selecting a Color Temperature

Enter Image > Color Temperature menu, and then press [Enter]. Options available to Color Temperature settings will depend on the choice of the signal

type.

1. Cool: Provides the highest color temperature. Cool colors allow the image to display white colors with the more blue undertones compared to other temperatures.

2. Normal: Maintains a normal white color tone.

3. Warm: White colors in the image will be provided with a light red undertone.

Setting a preferred color temperature

1. Enter Image > Color Temperature menu, and then press [Enter].

2. Press / to select Cool, Normal or Warm, and press [Enter].

3. Press / to select the item you wish to change, then press / to adjust its value.

● Red Gain/Green Gain/Blue Gain: Adjusts the contrasts of the red, green, and

blue colors.

● Red Offset/Green Offset/Blue Offset: Adjusts the brightness of red, green, and

blue colors.

Select a gamma setting

Gamma refers to the relationship between input source and image brightness.

1. Enter Image > Advanced menu and then press [Enter].

2. Press / to select Gamma and then press / to select the required settings.

Color Management

Only in permanent installations with controlled lighting levels such as boardrooms, lecture theaters, or home theaters, should color management be considered. Color management provides ne color control adjusent to allow for more accurate color reproduction, should you require it.

If you have purchased a test disc that contains various color test patterns that can be used to test the color presentation of monitors, TVs, and projectors, any image from the disc can

be projected on screen and adjusted using the Color Management menu.

To adjust the settings:

1. Open the OSD menu, go to Image > Advanced > Color Management menu.

2. Press [Enter] to bring up the Color Management

Red

Yellow

Green

page.

3. Select Primary Color and press / to select any

one of the colors from red, yellow, green, cyan, blue, or magenta.

CyanMagenta

4. Press  to select the Hue, then press / to select the range. Enlarging the range will include colors

Blue

composed of higher proportions of 2 similar colors.

Please refer to the illustration to the right for how the colors relate to each other.

For example, if you select red and set the range to 0, you will only select pure red areas of the projected image. Increasing the range will include shades of red closer to yellow and magenta.

5. Press  to select Saturation, then press / to adjust its values according to your preferences. The effect of each adjustment will be immediately reected upon the image. For example, if you select Red and set its value at 0, only the saturation of pure red

will be affected.

Saturation is the amount of that color in a video picture. Lower settings produce less saturated colors. A setting of 0 will remove that color from the image entirely. If the saturation is too high, that color will be overpowering and unrealistic.

6. Press  and select Gain, then press / to adjust its values according to your preferences. This affects the contrast level of the primary color selected. The effect of each adjustment will be immediately reected upon the image.

7. Repeat steps 3 to 6 to carry out other color adjustments.

8. Make sure you have made all of the desired adjustments.

9. Press [Exit] to save the settings and exit.

Setting the Presentation Timer

The presentation timer can indicate the presentation time on-screen to help you achieve better time management when giving presentations. Follow these steps to utilize this function:

1. Enter Basic > Presentation Timer menu.

2. Press [Enter] to show the Presentation Timer page.

3. Select Timer Period and press / to conrm the duration. Duration can be set to

1 to 5 minutes, with 1 minute increments, or 5 to 240 minutes. The options are 5, 10, 15, 20, 60, 120, 240 minutes.

Once the timer has been activated, resetting the timer interval will re-activate the timer.

4. Press  and select the Timer Display. Then press / to select whether to display or hide the on-screen timer.

Selection Description

Always Displays the timer on screen throughout the presentation time. 1 min/2 min/3 min Display timer on-screen in the last 1 / 2 / 3 minutes.

Never Hides the timer throughout the presentation time.

5. Press  and select Timer Position, and then press / to set timer location.

Top-Left  Bottom-Left  Top-Right  Bottom-Right

6. Press  to select Timer Counting Direction, then press / to select the required timer method.

Selection Description Count Up Increases from 0 to the preset time. Count Down Decrease from the preset time to 0.

7. To activate Presentation Timer, press  and select Start Counting, then press / to select Yes. The timer will start counting after exit the OSD menu.

To cancel the timer, perform the following steps:

1. Enter Basic > Presentation Timer menu.

2. Press  and select Start Counting.

3. Select No. The timer will stop counting after exit the OSD menu.

Hiding the image

In order to draw the audience’s attention to the presenter, you may press Blank

to hide the screen image. Press any key on the projector or remote to restore the image. After hiding the image, the lower right corner of the screen will display the text

[Blank].

You can go to Basic > Blank Timer menu to set blank screen duration. Once the

blank screen countdown is complete, the image will be automatically re-displayed.

After pressing [Blank], the projector will automatically enter Power Saving mode.

Caution Do not block the projector lens. The blocking item may be heated to the point of deformation or

may even cause a re.

Locking control keys

Locking the control buttons of the projector allows you to prevent projector settings from being changed accidentally (by children, for example). Once Panel Key Lock has been activated, with the exception of the Power button, none of the buttons on

the Projector could be used.

1. Go to System > Panel Key Lock menu.

2. Press / and select ON. To switch off the Panel Key Lock, press  and hold the button on the Projector for 3

seconds. You may also use the remote to enter System > Panel Key Lock menu, press / and select OFF.

Buttons on the remote control can still be used even if the Panel Key Lock function has been switched on.

If you press the Power button to switch off the projector without switching off the Panel Key Lock function, the projector buttons will remain locked when you switch it on the next time.

Light source settings

Light Source Mode Setting light source mode.

● Normal: 100% light source power

● Power Saving: 80% light source power

● Custom: 20%/40%/ 60%/ 80%/ 100% light source power for selection by user.

Light Source Hours Displays the time (hours) that the light source has been running.

Extending light source life

To keep the light source life as long as possible, you can do the following settings via the OSD menu.

Use the Power Saving mode to reduce system noise and power by 20%. If you select Power Saving mode, the light intensity will decrease and the projection pattern will be darker.

Switching the projector setting to Power Saving mode also extends the light source.

To set Power Saving mode, go to Advanced > Light Source Settings > Light Source Mode, press / to select Power Saving, or press [Eco Mode] on the

remote control to make the choice.

Setting Auto Power Off

This function allows the projector to shut down automatically after the set time, to avoid unnecessary wastage of the light source.

1. Open the OSD menu and go to the Power Management > Smart Energy

menu.

2. Press [Enter] to display the Smart Energy page.

3. Select Auto Power Off and press / to select the time.

4. If the pre-set time length is not suitable for your needs, select Disable. The

projector will not automatically shut down in a certain time period.

Setting the Sleep Timer

This function allows the projector to shut down automatically after the set time, to avoid unnecessary wastage of the life of the light source.

1. Open the OSD menu and go to the Power Management > Smart Energy

menu.

2. Press [Enter] to display the Smart Energy page.

3. Select Sleep Timer and press / to select the time.

4. If the length of the pre-set time does not apply to your presentation, select

Disable. The projector will not automatically shut down in a certain time period.

Set power saving

If no input source is detected after 5 minutes. The projector will reduce power consumption to avoid unnecessary wastage of the life of the light source. You can further decide whether to let the projector turn off after the set time.

1. Open the OSD menu and go to the Power Management > Smart Energy

menu.

2. Press [Enter] to display the Smart Energy page.

3. Select Power Saving Press / and select Enable.

4. When Enable is selected, the light source of the projector will be changed

to Eco mode 5 minutes after no signal is detected. If the projector has not

detected the signal after 20 minutes, its light source power will be changed to SuperEco mode.

Operations at high altitudes

We recommend using the High Altitude Mode when the environment is at 1500 to 3000 meters above sea level and the temperature is between 5°C to 25°C.

Note Do not activate High Altitude Mode if the environment is at 0 to 1500 meters above sea level and the temperature is between 5°C to 35°C. Activating High Altitude Mode under such circumstances will lead to excessive cooling of the projector.

Activating High Altitude Mode:

1. Open the OSD menu and enter System > High

Altitude Mode menu.

2. The conrm message will be shown, and press / to select Yes.

3. Press [Enter]. There is a chance that louder operational noises will be generated when using the

projector in High Altitude Mode. The reason for this is the increased fan speed

necessary to improve overall system cooling and performance. Using this projector under extreme environments that exceed the aforementioned

limits may lead to auto-shutdown designed to prevent overheating of the projector. Under such circumstances, you should switch to High Altitude Mode to solve these issues. However, this does not mean that this projector is able to operate under any and all harsh or extreme conditions.

Using the CEC function

This projector supports the Consumer Electronics Control (CEC), allowing you to connect to HDMI and achieve synchronized power ON/OFF operations. This means that when a device that also supports CEC is connected to the HDMI input jack of the projector, switching off the power of the projector will also automatically switch off the power of the connected device. Switching on the power of the connected device will also automatically switch on the projector.

Activating the CEC function:

1. Open the OSD menu and enter Power Management > Auto Power On > CEC menu.

2. Press / and select Enable.

To ensure proper operations of the CEC function, please verify that the target device has been connected to the HDMI input jack via an HDMI cable and that the CEC function has been activated.

CEC function may not be usable according to the connected equipment.

3D functions

This projector also comes with 3D functions that offer greater depth and immersion when viewing 3D movies, videos, sports, and games. You would need a pair of 3D glasses when viewing 3D images and videos.

If the 3D signal comes from an HDMI 1.4a compatible device, this projector will look for a 3D Sync data signal. Once detected, the projector will automatically switch to 3D projection. Under other circumstances, you may need to manually select the 3D Sync format to ensure that the proper projection of 3D images.

Selecting 3D Sync formats:

1. Use the remote control or control panel to open the OSD menu, select Advanced > 3D Settings menu.

2. Press [Enter] to bring up the 3D Settings page.

Once 3D Sync function has been activated:

• Brightness of the projected image will be reduced.

• Color modes cannot be adjusted.

• Zoom functions can only enlarge the image to a limited degree.

If the 3D image has been severely inverted, you may set the 3D Sync Invert function to [Invert] to correct this problem.

Control the projector through the local area network

This projector supports the Crestron® software.After correct settings in the wired local

area network menu are nished, the projector can be managed on the computer with the browser when the computer and the projector are correctly connected to the same local

area network.

(Example of connection)

Congure the wired local area network If you are in a DHCP environment:

1. Connect one end of the RJ45 cable to the RJ45 local area network input jack of the projector, and connect the other end to the RJ45 port.

2. Open the OSD menu and enter the Advanced > Network Settings.

3. Select DHCP and then press / to select On.

4. Press  to select the Apply and then press [Enter].

5. Please wait for about 15-20 seconds and then re-enter the page of the wired local

area network. The IP address, subnet mask, default gateway and DNS server settings will be displayed. Please remember the IP address displayed in the IP

address.

If the IP address still does not display, contact the network administrator.

If the RJ45 cable is not correctly connected, the IP address, subnet mask, default gateway and DNS server settings will be displayed as 0.0.0.0. Make sure the cable has been correctly connected and re-execute the above steps.

To connect to the projector when the projector is in the standby mode, set the Advanced > Network Settings > Standby LAN control to On.

If you are in a non-DHCP environment:

1. Repeat the above steps 1-2.

2. Select DHCP and then press / to select Off.

3. Contact your ITS administrator for the setting information about IP address, subnet

mask, default gateway and DNS server.

4. Press  to select the item you want to modify and then press [Enter].

5. Press / to move the cursor and then press / to input the value.

6. To save the settings, press [Enter]. If you do not want to save the settings, press [Exit].

7. Press  to select the Apply and then press [Enter].

To connect to the projector when the projector is in the standby mode, make sure the DHCP has set to Off and the IP address, subnet mask, default gateway and DNS server information have been acquired after the projector is powered on.

Control the projector with the web browser

If the correct IP address of the projector is acquired, and the projector is powered on or in the standby mode, any computer in the same local area network can be used to

control the projector.

If Microsoft Internet Explorer is used, make sure the version is 7.0 or higher.

The screenshots in this manual are for reference only. Actual OSD design may differ.

1. Enter the address of the projector in the address bar of your browser and press [Enter].

2. The homepage of “Network Control” is displayed.

Access to the Network Settings or Email Alert web page needs the administrator password. The

default password is “0000”.

3. You can adjust AMX and SNMP settings on this page. On the AMX device discovery,

the controller connected to the AMX of the same network will nd out the projector when ON is selected. For details of the AMX Device Discovery, please access the AMX website: http://www.amx.com/.

4. If the projector is connected to the network which supports the SMTP (Simple Mail Transfer Protocol), you can congure it to send alarms via emails when important

events occur.

5. Crestron (e-Control) page display Crestron e-Control user interface. For details, please refer to “About Crestron e-Control®”.

Please note the input length limits in the following table (including space and other punctuation marks):

Type item Input length Maximum character

DHCP/Manual (None) IP Address XXX.XXX.XXX.XXX

Network Settings

Email Alert

Network

Password

SNMP

Email Setting

SMTP Setting

Subnet Mask XXX.XXX.XXX.XXX Gateway XXX.XXX.XXX.XXX DNS Server XXX.XXX.XXX.XXX AMX device discovery (None) Administrator (None)

New Password 4

Conrm Password 4 SysLocation 22 SysName 22 SysContact 22

To 40 Cc 40

Subject 40 From 40 Server 30 User Name 21

Password 14

Alert Condition

/ > < $ % + \ ‘ “ are forbidden.

Fan Error (None) Light source Error (None)

Over Temperature (None) Light source Time Alert (None) Submit (None)

Issue Test Mail (None)

About Crestron e-Control

1. The Crestron e-Control® page provides various virtual buttons to control the projector or adjust the projected image.

You can press

to display

/

more buttons.

i. The functions of those buttons are identical with those on the OSD menu or

remote control.

ii. To switch the input signal source, please click the required signal.

Menu button can be used to return to the previous OSD menu, exit and save menu settings. The signal source list may differ from the available interfaces on the projector. The web browser needs some time to perform change synchronization to the projector when the

projector control panel or remote control is used to change the OSD menu settings.

2. The Tools page can be used to manage the projector, congure the LAN control settings, and perform remote network operation security access to the projector.

i iv

iii

i. This part can be used only in the case that the Crestron control system is used.

Please contact Creston or refer to its user guide to get a knowledge of the

installation information.

ii. You can name the projector, and record its position and responsible person.

iii. You can adjust the wired local area network.

iv. After setting is nished, the remote network operation access to the projector is

protected with a password.

v. After setting is nished, access to the Tools page is protected with a password.

To avoid mistakes, please input the English letters and digits in the Tools page. After adjustment, press the Send button and the data will be saved in the projector.

vi. Press Exit and then you can return to the remote network operation page.

Please note the input length limits in the following table (including space and other punctuation marks):

Type item Input length Maximum character

Crestron Control IP Address 16

IP ID 4 Port 5

Projector Projector Name 32

Location 32 Assigned To 32

Network Conguration DHCP (Enabled) (None)

IP Address 16

Subnet Mask 16 Default Gateway 16 DNS Server 16

User Password Enabled (None)

New Password 26

Conrm 26

Admin Password Enabled (None)

New Password 26 Conrm 26

3. The Info page displays the information and status of this projector.

Press Exit and then you can return to the remote

network operation page.

4. Press “Contact IT Help” button, and then a HELP DESK window will be displayed in

the upper right corner of the screen. You can send information to the RoomView™ software administrator / user connected to the same local area network.

For details, please access http: // www.crestron.com and www.crestron.com/ getroomview.

**Crestron RoomView On the “Edit Room” page, input the IP address (or the host name) as the content

displayed in the screen display menu of the projector, and input “02” as the IPID, and input “41794” as the reserved Crestron control port.

Regarding the Crestron RoomView™ settings and command method, please access the following website to obtain the RoomView™ User Guid and more information: http://www.crestron.com/products/roomview_connected_embedded_projectors_

devices/resources.asp

Support PJLink™, SNMP, AMX and Xpanel formats

This projector is compatible with PJLink™, SNMP V.1, AMX or Xpanel V1.10. For details, please respectively refer to the User Guide or access the website to control and manage the projector.

Using the projector under standby mode

A number of projector functions can be used under Standby Mode (plugged in to power but not switched on). To use those functions, please conrm the cables and wires have been correctly connected. Refer to the chapter on cable connections for more information on cable connections.

Active VGA Out After the COMPUTER 1 and COMPUTER OUT jacks are correctly connected to the

equipment, select Power Management > Standby Settings > Active VGA Out > On to output the VGA signal. The projector only outputs the signal received by COMPUTER

1. LAN control

Setting in the Advanced > Network Settings > Standby LAN control menu drives the projector to provide network functions in the standby mode. For details, please refer to “Control the projector through the local area network”.

Switch off the projector

1. Press the Power button. A conrmation message will be displayed on screen. The message will disappear if you do not respond within a few seconds.

2. Press the Power Button again, and the projector is turned off. Wait until the fan is completely stopped and unplug the power cord.

3. Disconnect the power cord from the wall socket if the projector will not be used in an extended period of time.

Menu operations

Menu system

Please note that the on-screen display (OSD) menu may vary according to the type of

signal received.

The projector must detect at least one valid signal in order to use the menu items. If no device has been connected to the projector or if no signal has been detected, only a few menu items will be accessible.

Main menu Sub-menu Options

Aspect Ratio Auto/4:3/16:9/16:10/Native

Up/Down: -40~40

Keystone

Left/Right: -40~40

Corner Adj.

1. Display

2. Image

Position

Phase 0~31 H. Size -15~15 Digital Zoom 0.8X~2.0X OverScan Off/1/2/3/4/5 3X Fast Input Yes/No

Color mode

Brightness 0~100 Contrast -50~50

Warm

Color Temperature

Normal Cool Color -50~50 Tint -50~50 Sharpness 0~31

Gamma

Horizontal: -5~5 Vertical: -5~5

Standard/Presentation/Movie/ Brightest/Photo

Red gain/Green gain/Blue gain/Red offset/Green offset/ Blue offset

1.8/2.0/2.2/2.35/2.5/Cubic/ sRGB

Advanced

Reset color settings

Brilliant Color Off/1/2/3/4/5/6/7/8/9/10 Noise Reduction 0~31

Red/Green/Blue/ Cyan/Magenta/ Yellow

Color Management

Primary color

Tint -99~99 Saturation 0~199 Gain 5~195

Reset/Cancel

Main menu Sub-menu Options

Signal Disable/VGA 1/ HDMI 1/ All

3. Power

Management

4. Basic

Auto Power On

Smart Energy

Standby Settings

Audio Settings

Presentation Timer

CEC Disable/Enable Direct Power On Off/On Auto Power Off Disable/10 min/20 min/30 min

Sleep Timer

Power Saving Disable/Enable Active VGA Out Off/On Active Audio Out Off/On Mute Off/On Volume 0~20 Timer Period 1/2/3/4/5/10/15/20/60/120/240

Timer Display

Timer Position

Timer Counting Direction

Start Counting Yes/No

Disable/30 min/1 hr/2 hr/3 hr/4 hr/8 hr/12 hr

Always/3 min/2 min/1 min/ Never

Top-Left/Bottom-Left/TopRight//Bottom-Right

Count down/count up

5. Advanced

Pattern Off/Test Card

Blank Timer

Message On/Off Splash Screen Blue/ViewSonic/Off

3D Sync

3D Settings

Save 3D Settings Yes/No 3D Sync Invert Disable/Enable

HDMI Settings

Network Settings

HDMI Format Auto/RGB/YUV HDMI Range Auto/Enhanced/Normal DHCP On/Off IP Address Subnet Mask Gateway DNS Server

Disable/5 min/10 min/15 min/20 min/25 min/30 min

Off/Frame sequence/Frame Packing/Top-Bottom/Side-BySide

Standby LAN control On/Off Apply Apply

Main menu Sub-menu Options

5. Advanced

6. System

Light Source Mode

Light source setting

DCR On/Off Closed Caption Off/CC1/CC2/CC3/CC4 Reset settings Reset/Cancel Language Multi-language OSD option Projector

Position

Menu Settings

High Altitude Mode

Quick Auto Search

Security Settings

Light Source Hours Light Source Power

Menu Display Time

Menu Position

Change Password

Power On Lock On/Off

Normal/Power Saving/ Custom

Front Table/Rear Table/Rear Ceiling/Front Ceiling

5 sec/10 sec/15 sec/20 sec/25 sec/30 sec

Center/Top-Left/Top-Right/ Bottom-Left/Bottom-Right

On/Off

Input Current Password/Input New Password

Panel Key Lock On/Off Remote control

code RS232 Baud

Rate 12V Trigger On/Off

• Source

• Color Mode

• Resolution

7. Information

Note: 1. Due to the update, it does not conform to the above content, without notice.

• Color System

• IP Address

• MAC Address

• Firmware

Version

• 3X Fast Input

1/2/3/4/5/6/7/8

2400/4800/9600/14400/19200/ 38400/57600/115200

Description of each menu

Function Description

Aspect Ratio See “Selecting the aspect ratio” for details. Keystone See “Perform keystone correction” for details. Corner Adj. See “Adjust four corners” for deatils.

Displays the position adjustment page. To move the projected image, use the directional arrow keys. The

values shown on the lower position of the page change

Position

1. Display menu

Phase

with every key press you made until they reach their maximum or minimum.

This function is only available when a PC and component input signal is selected.

The adjustment range may vary under different timings.

Adjusts the clock phase to reduce image distortion.

This function is only available when a PC and component input signal is selected.

Adjusts the horizontal width of the image.

H. Size

This function is only available when a PC and component input signal is selected.

Zoom Zoom in or out picture.

To avoid the appearance of the distorted image at the edge of the screen, use over-scanning technology

OverScan

to expand the image by 5% or even 10%, and the distorted image extends to the place outside the screen; only the middle part with better linearity is

shown.

Selecting On enables the function. This feature helps reduce the frame rate. Enabling quick response in local timing. The following settings will return to

3X Fast Input

factory defaults when enabled: aspect ratio, keystone correction, position, zoom, over scan. This function is only available if the optimum resolution input signal is

selected.

2. Image menu

Color mode See “Selecting a picture mode” for details. Brightness See “Adjusting Brightness” for details. Contrast See “Adjusting Contrast” for details.

For more details, please refer to “Selecting a

Color Temp.

Color Temperature” and “Setting a preferred color temperature”.

Function Description

2. Image menu

Advanced

Color

See “Adjusting Color” for details.

Tint

See “Adjusting Tint” for details.

Sharpness

See “Adjusting Sharpness” for details.

Gamma

See “Selecting a Color Temperature” for details.

Brilliant Color

See “Adjusting Brilliant Color” for details.

Noise Reduction

See “Reducing image noise” for details.

Color Management

See “Color Management” for details.

Reset color settings Returns all color settings to the factory preset values.

Signal

Set whether or not to automatically turn on when the projector is in the standby mode or the VGA or HDMI signal of 5V power is detected.

3. Power Management menu Auto Power On

Smart Energy

CEC

See “Using the CEC function” for details.

Direct Power On

Selecting On allows the projector to turn on automatically once the power is fed through the power

cord.

Auto Power Off

See “Setting Auto Power Off” for details.

Sleep Timer

See “Setting the Sleep Timer” for details.

Power Saving

See “Set power saving” for details.

Standby Settings See “Standby settings” for details.

Function Description

Audio Settings

Mute Volume

Presentation Timer See “Setting the Presentation Timer” for details.

4. Basic menu Pattern

The projector can display a test pattern. It helps you adjust the image size and focus and check that the projected image is free from distortion.

Blank Timer See “Hiding the image” for details.

Selecting On displays the current information on the

Message

screen when the projector is detecting or searching for a signal.

Splash Screen

Allows you to select which logo screen will be displayed during projector start-up.

3D settings See “3D functions” for details. HDMI settings See “Changing HDMI input settings” for details. Network Settings See “Network settings” for details. Light Source Settings See “Light source settings” for details.

Enables or disables the DCR (Dynamic Contrast Ratio) function. Selecting On enables the function and the projector will automatically switch the Lamp mode between normal and economic modes according to the input image detected.

DCR

This function is only available when a PC input signal is selected.

5. Advanced menu

Closed Caption

Reset Settings

After enabling DCR, frequent Lamp mode switching may shorten Lamp life and noise level will vary during operation.

Selects a preferred closed captioning mode when the selected input signal carries closed captions.

● Captions: An on-screen display of the dialogue, narration, and sound effects of TV programs and videos that are closed captioned (usually marked as “CC” in TV listings).

This function is only available when a Composite video input signal is selected and its system format is NTSC.

Caption Version

To view captions, select CC1, CC2, CC3, or CC4 (CC1 displays subtitles in the primary language of the region you are located in).

Returns all settings to the factory preset values.

The following settings will still remain: Keystone, Language, Projector Position, High Altitude Mode, Security Settings, 3D Sync Invert, Network Settings, Image Settings, Presentation Timer, Quick Auto Search and Remote control code.

Function Description

Language

Projector Position See “Choosing a location” for details.

Menu Settings

6. System menu

High Altitude Mode

Quick Auto Search See “Switching input signal” for details. Security Settings See “Using the password function” for details. Panel Key Lock See “Locking control keys” for details. Remote control code See “Remote control code” for details. RS232 Baud Rate See “RS232 command table” for details.

Sets the language for the On-Screen Display (OSD) menus. See “Using the menus” for details.

Menu Display Time

Sets the length of time the OSD will remain active after your last key press. The range is from 5 to 30 seconds in 5-second increments.

Menu Position

Sets the On-Screen Display (OSD) menu position. A mode for operation in high altitude areas. See

“Operations at high altitudes” for details.

A 12V trigger is provided, which can work according to the demands of your installation environment. Two options are available:

12V Trigger

7. Information menu

Current System Status

Off

If you choose this option, the projector does not send

an electronic signal when started.

The projector will send electronic signals from the bottom up when started, and send electronic signals from the top down when shut down.

Source

Shows the current signal source.

Color mode Shows the selected mode in the Image menu. Resolution

Shows the native resolution of the input signal.

Color System

Shows the input system format.

IP Address

Displays the IP address of the projector.

MAC Address

Displays the MAC address of the projector.

Firmware Version

Shows the current rmware version.

3X Fast Input

Maintenance

Care of the projector

Do not attempt to disassemble any part of the projector. Contact your dealer if you need to replace any parts.

Cleaning the lens

You can clean the dust-free glass lens if you notice any dirt or dust on its surface.

●Use a canister of compressed air to remove dust.

●Use a lens cleaning wipe or soft, or a moist cloth with some detergent to clean away any dust or dirt on the dust-free glass.

Note Do not apply any granule material on the dust-free glass.

Cleaning the projector case

Before cleaning the case, please refer to the proper shutdown procedure described in “Switch off the projector” to shutdown the projector and unplug the power cable.

●To remove dirt or dust, wipe the case with a soft, lint-free cloth.

●To remove stubborn dirt or stains, moisten a piece of soft cloth with water and a neutral pH detergent. Then wipe the case.

Note Never use wax, alcohol, benzene, thinners, or other chemical-based detergents. These can damage the case.

Storing the projector

Follow the instructions below to store the projector for an extended time:

●Make sure the temperature and humidity of the storage area are within the

recommended range for the projector. Please refer to “Specications” or inquire your

dealer for details of the recommended range.

●Retract the projector support pegs.

●Remove the battery from the remote control.

●Pack the projector in its original packaging or equivalent material.

Transporting the projector

It is recommended that you ship the projector within its original packaging or

equivalent material.

LED Indicator

Projector status Power indicator Temp indicator Lamp indicator

Stand-by mode Green Flashing Off Off

Normally on Green Off Off

Normal Operations Green Off Off

Temperature Error

Fan Error 1 Green Red Flashing Green

Fan Error 2 Green Red Flashing Green Flashing

Fan Error 3 or 4 Green Red Flashing Orange Flashing

Color Wheel Error Green Off Orange

Light bulb

abnormal

Heat dissipation

state

Green Red Flashing Orange

Green Red Flashing Off

Green Off Red

Green Green Flashing Off

Troubleshooting

Projector is not shutting down

Cause Remedy

There is no power from the power cable.

Plug one end of the power cable at the AC inlet of the projector and the other end in the power outlet. If the power outlet has a switch, make sure that it is switched on.

Attempting to turn the projector on again during the cooling process.

No picture

Cause Remedy

Video source is not turned on or is not connected correctly.

The projector is not correctly connected to the input signal device.

The input signal has not been correctly selected.

Blurred image

Cause Remedy

Wait until the cooling down process has completed.

Switch the video source on and check that the signal cable is connected correctly.

Check the connection.

Select the correct input signal by using the [Source] key on the projector or remote control.

The projection lens is not correctly focused.

The projector and the screen are not aligned properly.

Use the focus function to adjust lens focus.

Adjust projection angle and direction as well as the height of the projector where necessary.

Remote control does not work

Cause Remedy

The battery is out of power. Replace the batteries. There is an obstacle between the remote

control and the projector.

You are too far away from the projector.

The remote control does not match the remote control code of the projector.

Remove the obstacle.

Stand within 8 meters (26 feet) of the projector.

Adjust the remote control code.

Specications

Projector specications

● All specications are subject to change without notice.

● Not all projector models are available at your location.

LS625X LS625W

Input Terminals

1 VGA input (DB 15 pin) x2 x2

2 HDMI (v1.4 with audio ) x2 x2

3 Video (RCA) x1 x1

4 Audio input (3.5mm mini jack) x1 x1

5 S-Video x1 x1

Output Terminals

1 Audio output (3.5mm mini jack) x1 x1

2 USB (mini A type) 5V/1.5A x1 x1

3 Speaker x1 x2

4 VGA output x1 x1

Control Terminals

1 RS232 (9 pin 1 type) x1 x1

2 USB cable (mini B type) x1 x1

3 12V Trigger x1 x1

4 LAN x1 x1

Fuse specications

The fuse number used on the power PCB board is: F1, and the speciﬁcations are: 250V,

T6.3AH

Dimensions

383.7mm

147.7mm

383.7mm

LS625X LS625W

7.0mm

150.0mm

147.7mm

291.5mm

Ceiling mount installation

223.0mm

291.5mm

Note: It is recommended to use the M4L8 screw for xing the projector using the M4 screw

hole. (M4/ L8 x 4)

Timing chart

Signal Resolution (pixels) Aspect Ratio Refresh rate (Hz)

VGA 640x480 4:3 60/72/75/85

SVGA 800x600 4:3 60/72/75/85

XGA

WXGA

Analog RGB

1024x768 4:3 60/70/75/85

1152x864 4:3 75

1280x768 15:9 60

1280x800 16:10 60/75/85

1360x768 16:9 60

1366x768 16:9 60

Quad-VGA 1280x960 4:3 60/85

SXGA 1280x1024 5:4 60

SXGA+ 1400x1050 4:3 60

WXGA+ 1440x900 16:10 60

UXGA 1600x1200 4:3 60

WSXGA+ 1680x1050 16:10 60

HD 1280x720 16:9 60

MAC 13” 640x480 4:3 67

MAC 16” 832x624 4:3 75

MAC 19” 1024x768 4:3 75

MAC 21” 1152x870 4:3 75

HDTV (1080p) 1920x1080 16:9 60

HDMI

Signal Resolution (pixels) Aspect Ratio Refresh rate (Hz)

VGA 640x480 4:3 60

SVGA 800x600 4:3 60

XGA 1024x768 4:3 60

1280x768 15:9 60

1280x800 16:10 60

WXGA

1360x768 16:9 60

1366x768 16:9 60

Quad-VGA 1280x960 4:3 60

SXGA 1280x1024 5:4 60

SXGA+ 1400x1050 4:3 60

WXGA+ 1440x900 16:10 60

WSXGA+ 1680x1050 16:10 60

HDTV (1080p) 1920x1080 16:9 50/60

HDTV (1080i) 1920x1080 16:9 50/60

HDTV (720p) 1280x720 16:9 50/60

SDTV(480p) 720x480 4:3/16:9 60

SDTV(576p) 720x576 4:3/16:9 50

SDTV (480i) 720x480 4:3/16:9 60

SDTV (576i) 720x576 4:3/16:9 50

3D (including HDMI signal)

Signal Resolution (pixels) Aspect Ratio Refresh rate (Hz)

SVGA 800x600 4:3 60*/120

XGA 1024x768 4:3 60*/120

HD 1280x720 16:9 50*60*

WXGA 1280x800 16:9 60*

For Video Signal

Signal Resolution (pixels) Aspect Ratio Refresh rate (Hz)

SDTV (480i)** 720x480 4:3/16:9 60

* 50 Hz and 60 Hz signals are supported for side by side, Top and Bottom, and Frame Sequential formats. ** The video signal (SDTV 480i) supports only the frame Sequential format.

Within frame packing formats

Signal Resolution (pixels) Aspect Ratio Refresh rate (Hz)

1080p 1920x1080 16:9 23.98/24

720p 1280x720 16:9 50/59.94/60

Within side by side formats

Signal Resolution (pixels) Aspect Ratio Refresh rate (Hz)

1080i 1920x1080 16:9 50/59.94/60

720p 1280x720 16:9 50/60

Within Top and Bottom formats

Signal Resolution (pixels) Aspect Ratio Refresh rate (Hz)

HDMI 3D

1080p 1920x1080 16:9 23.98/24

720p 1280x720 16:9 50/59.94/60

Component video

Signal Resolution (pixels) Aspect Ratio Refresh rate (Hz)

HDTV (1080p) 1920x1080 16:9 50/60

HDTV (1080i) 1920x1080 16:9 50/60

HDTV (720p) 1280x720 16:9 50/60

SDTV(480p) 720x480 4:3/16:9 60

SDTV(576p) 720x576 4:3/16:9 50

SDTV (480i) 720x480 4:3/16:9 60

SDTV (576i) 720x576 4:3/16:9 50

Composite video

Signal Aspect Ratio Refresh rate (Hz)

NTSC 4:3 60

PAL 4:3 50

PAL60 4:3 60

SECAM 4:3 50

Copyright information

Copyright

Copyright 2018 All rights reserved. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system or translated into any language or computer language, in any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise, without the prior written permission of ViewSonic.

Disclaimer

ViewSonic does not make any statement or warranty, expressed or implied, for the merchantability and

tness for a particular purpose with respect to any contents within this manual. Additionally, ViewSonic

reserves the right to revise and update the contents of this manual without notice.

*DLP and Digital Micromirror Device (DMD) are trademarks of Texas Instruments. Other names would be the copyrights of the respective companies or organizations.

Appendix

IR control table

Button Format Byte 1 Byte 2 Byte 3 Byte 4

PgDn NEC X3 F4 5 FA PgUp NEC X3 F4 6 F9 Blank NEC X3 F4 7 F8

auto sync NEC X3 F4 8 F7

Up /Keystone V+ NEC X3 F4 0B F4

Down /Keystone V- NEC X3 F4 0C F3

Left/Keystone H- NEC X3 F4 0E F1

Right/Keystone H+ NEC X3 F4 0F F0

Color Mode NEC X3 F4 10 EF

Mute NEC X3 F4 14 EB

Enter NEC X3 F4 15 EA Power On NEC X3 F4 4F B0 Power Off NEC X3 F4 4E B1

Exit NEC X3 F4 28 D7

Eco Mode NEC X3 F4 2B D4

Menu NEC X3 F4 30 CF

Source NEC X3 F4 40 BF

Pattern NEC X3 F4 55 AA

HDMI1 NEC X3 F4 58 A7 HDMI2 NEC X3 F4 59 A6

Volume+ NEC X3 F4 82 7D

Volume- NEC X3 F4 83 7C

Zoom + NEC X3 F4 67 98

Zoom - NEC X3 F4 68 97 Freeze NEC X3 F4 3 FC Aspect NEC X3 F4 13 EC COMP NEC X3 F4 41 68

information NEC X3 F4 97 BC

Network NEC X3 F4 69 96

Presentation Timer NEC X3 F4 27 D6

Address Code

Code 1 83F4

Code 2 93F4

Code 3 A3F4

Code 4 B3F4

Code 5 C3F4

Code 6 D3F4

Code 7 E3F4

Code 8 F3F4

RS232 command table

Pin Description Pin Description

1 NC 2 RX

3 TX 4 NC

5 GND 6 NC

7 RTSZ 8 CTSZ

9 NC

RS-232 protocol

Baud Rate 115200bps (default)

Data Length 8 bit

Parity check None

Stop bit 1 bit

flow control None

5963

16 20

Light source

Write

Light source

Write

Light source

Write

Message

Write

0x06 0x14 0x00 0x04 0x00 0x34 0x11

0x03 0x14 0x00 0x00 0x00 0x14

0x05 0x14 0x00 0x03 0x00 0x00 0x00 0x01

The below table list all RS232 commands frequently used:

No. Function Type Action Command Response The response of Query Read command

1 Power Write ON 0x06 0x14 0x00 0x04 0x00 0x34 0x11

2 Power Write OFF 0x06 0x14 0x00 0x04 0x00 0x34 0x11

3 Power Read Status 0x07 0x14 0x00 0x05 0x00 0x34 0x00

4 Projector

Status

5 Reset All

Settings

6 Reset Color

Settings

Splash Screen

High Altitude Mode

Light sourc Mode Light source

Mode

Light source

Mode

Light sourc

Mode

Light source Mode

Message Write OFF 0x06 0x14 0x00 0x04 0x00 0x34 0x11

Message Read Status 0x07 0x14 0x00 0x05 0x00 0x34 0x00

Read Status

(Note 7)

Write Reset All

Settings

Write Reset Color

Settings

Write Blue 0x06 0x14 0x00 0x04 0x00 0x34 0x11

Write ViewSonic 0x06 0x14 0x00 0x04 0x00 0x34 0x11

Write OFF 0x06 0x14 0x00 0x04 0x00 0x34 0x11

Read Status 0x07 0x14 0x00 0x05 0x00 0x34 0x00

Write OFF 0x06 0x14 0x00 0x04 0x00 0x34 0x11

Write ON 0x06 0x14 0x00 0x04 0x00 0x34 0x11

Read Status 0x07 0x14 0x00 0x05 0x00 0x34 0x00

Write Normal

Write Eco

Write Custom 40 0x06 0x14 0x00 0x04 0x00 0x34 0x11

Write 0x06 0x14 0x00 0x04 0x00 0x34 0x1

Read Status 0x07 0x14 0x00 0x05 0x00 0x34 0x00

Custom 20 0x06 0x14 0x00 0x04 0x00 0x34 0x11

Custom 60 0x06 0x14 0x00 0x04 0x00 0x34 0x11

Custom 80

Custom 100

0x00 0x00 0x5D

0x01 0x00 0x5E

0x00 0x11 0x00 0x5E

0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x11 0x26 0x84

0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x02 0x00 0x5F

0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x2A 0x00 0x87

0x0A 0x01 0x68

0x0A 0x02 0x69

0x0A 0x04 0x6B

0x00 0x11 0x0A 0x68

0x0C 0x00 0x69

0x0C 0x01 0x6A

0x00 0x11 0x0C 0x6A

0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x10 0x00 0x6D 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x10 0x01 0x6E

0x10 0x04 0x71

0x10 0x05 0x72

0x10 0x06 0x73

0x10 0x07 0x74 0x06 0x14 0x00 0x04 0x00 0x34 0x11

0x10 0x08 0x75

0x00 0x11 0x10 0x6E

0x27 0x00 0x84

0x27 0x01 0x85

0x00 0x11 0x27 0x85

0x03 0x14 0x00 0x00 0x00 0x14 0x05 0x14 0x00 0x03 0x00 0x00 0x00 0x01

0x03 0x14 0x00 0x00 0x00 0x14 0x05 0x14 0x00 0x03 0x00 0x00 0x00 0x00

0x05 0x14 0x00 0x03 0x00 0x00 0x00 0x01 0x18

Wa rm u p :0x 05 0x1 4 0x 00 0x 03 0x00 0 x00 0x00 0 x01 0x1 8 Co ol down :0x 05 0x14 0x00 0x 03 0x00 0x0 0 0x 00 0x03 0x1 A Po we r On :0 x05 0x14 0 x00 0x 03 0 x00 0x 00 0 x00 0x 02 0x 19 Po we r Do wn :0 x05 0x14 0 x00 0x 03 0 x00 0x 00 0x 00 0x 00 0 x17 0x03 0x14 0x00 0x00 0x00 0x14

0x03 0x14 0x00 0x00 0x00 0x14

0x03 0x14 0x00 0x00 0x00 0x14 0x05 0x14 0x00 0x03 0x00 0x00 0x00 0x01

0x03 0x14 0x00 0x00 0x00 0x14 0x05 0x14 0x00 0x03 0x00 0x00 0x00 0x02

0x03 0x14 0x00 0x00 0x00 0x14 0x05 0x14 0x00 0x03 0x00 0x00 0x00 0x04

0x05 0x14 0x00 0x03 0x00 0x00 0x00 0x02 0x19

0x03 0x14 0x00 0x00 0x00 0x14 0x05 0x14 0x00 0x03 0x00 0x00 0x00 0x00

0x03 0x14 0x00 0x00 0x00 0x14

0x05 0x14 0x00 0x03 0x00 0x00 0x00 0x00 0x17

0x03 0x14 0x00 0x00 0x00 0x14 0x05 0x14 0x00 0x03 0x00 0x00 0x00 0x00

0x03 0x14 0x00 0x00 0x00 0x14 0x05 0x14 0x00 0x03 0x00 0x00 0x00 0x01

0x03 0x14 0x00 0x00 0x00 0x14 0x05 0x14 0x00 0x03 0x00 0x00 0x00 0x04

0x03 0x14 0x00 0x00 0x00 0x14 0x05 0x14 0x00 0x03 0x00 0x00 0x00 0x05

0x03 0x14 0x00 0x00 0x00 0x14 0x05 0x14 0x00 0x03 0x00 0x00 0x00 0x06

0x03 0x14 0x00 0x00 0x00 0x14 0x05 0x14 0x00 0x03 0x00 0x00 0x00 0x07

0x03 0x14 0x00 0x00 0x00 0x14 0x05 0x14 0x00 0x03 0x00 0x00 0x00 0x08

0x05 0x14 0x00 0x03 0x00 0x00 0x00 0x00 0x17

0x03 0x14 0x00 0x00 0x00 0x14 0x05 0x14 0x00 0x03 0x00 0x00 0x00 0x00

0x05 0x14 0x00 0x03 0x00 0x00 0x00 0x01 0x18

0x18

0x17

0x18

0x19

0x1B

0x17

0x05 0x14 0x00 0x03 0x00 0x00 0x00 0x01 0x18

0x17

0x18

0x1B

0x1C

0x1D

0x1E

0x1F

0x17

0x18

No. Function Type Action Command Response The response of Query Read command

Aspect ratio

Write

Cycle

0x06 0x14 0x00 0x04 0x00 0x34 0x13

0x03 0x14 0x00 0x00 0x00 0x14

Horizontal

Write

Shift Right

0x06 0x14 0x00 0x04 0x00 0x34 0x12

0x03 0x14 0x00 0x00 0x00 0x14

Projector Position

3D Sync Write OFF 0x06 0x14 0x00 0x04 0x00 0x34 0x12

3D Sync Write Auto 0x06 0x14 0x00 0x04 0x00 0x34 0x12

3D Sync Write Frame

3D Sync Write Frame Packing

3D Sync Write Top Bottom 0x06 0x14 0x00 0x04 0x00 0x34 0x12

3D Sync Write Side by Side 0x06 0x14 0x00 0x04 0x00 0x34 0x12

3D Sync Read Status 0x07 0x14 0x00 0x05 0x00 0x34 0x00

3D Sync

nvert

3D Sync

nvert

3D Sync

nvert

Contrast Write Decrease 0x06 0x14 0x00 0x04 0x00 0x34 0x12

Contrast Write Increase 0x06 0x14 0x00 0x04 0x00 0x34 0x12

Contrast Read Get Value 0x07 0x14 0x00 0x05 0x00 0x34 0x00 I

Brightness Write Decrease 0x06 0x14 0x00 0x04 0x00 0x34 0x12 I

Brightness Write Increase 0x06 0x14 0x00 0x04 0x00 0x34 0x12 I

Brightness Read Get Value 0x07 0x14 0x00 0x05 0x00 0x34 0x00

Aspect ratio Write Auto 0x06 0x14 0x00 0x04 0x00 0x34 0x12

Aspect ratio Write 4:3 0x06 0x14 0x00 0x04 0x00 0x34 0x12

Aspect ratio Write 16:9 0x06 0x14 0x00 0x04 0x00 0x34 0x12

Aspect ratio Write 16:10 0x06 0x14 0x00 0x04 0x00 0x34 0x12

Aspect ratio Write Native 0x06 0x14 0x00 0x04 0x00 0x34 0x12

Write Front Table 0x06 0x14 0x00 0x04 0x00 0x34 0x12

Write Rear Table 0x06 0x14 0x00 0x04 0x00 0x34 0x12

Write Rear Ceiling 0x06 0x14 0x00 0x04 0x00 0x34 0x12

Write Front Ceiling 0x06 0x14 0x00 0x04 0x00 0x34 0x12

Read Status 0x07 0x14 0x00 0x05 0x00 0x34 0x00

Sequential

Write OFF 0x06 0x14 0x00 0x04 0x00 0x34 0x12

Write ON 0x06 0x14 0x00 0x04 0x00 0x34 0x12

Read Status 0x07 0x14 0x00 0x05 0x00 0x34 0x00

0x00 0x00 0x5E

0x00 0x01 0x5F

0x00 0x02 0x60

0x00 0x03 0x61

0x00 0x12 0x00 0x5F

0x20 0x00 0x7E

0x20 0x01 0x7F

0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x20 0x02 0x80

0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x20 0x03 0x81

0x20 0x04 0x82

0x20 0x05 0x83

0x00 0x12 0x20 0x7F

0x21 0x00 0x7F

0x21 0x01 0x80

0x00 0x12 0x21 0x80

0x02 0x00 0x60

0x02 0x01 0x61

0x00 0x12 0x02 0x61

0x03 0x00 0x61

0x03 0x01 0x62

0x00 0x12 0x03 0x62

0x04 0x00 0x62

0x04 0x02 0x64

0x04 0x03 0x65

0x04 0x04 0x66

0x04 0x09 0x6B

0x03 0x14 0x00 0x00 0x00 0x14 0x05 0x14 0x00 0x03 0x00 0x00 0x00 0x00

0x03 0x14 0x00 0x00 0x00 0x14 0x05 0x14 0x00 0x03 0x00 0x00 0x00 0x01

0x03 0x14 0x00 0x00 0x00 0x14 0x05 0x14 0x00 0x03 0x00 0x00 0x00 0x02

0x03 0x14 0x00 0x00 0x00 0x14 0x05 0x14 0x00 0x03 0x00 0x00 0x00 0x03

0x05 0x14 0x00 0x03 0x00 0x00 0x00 0x00 0x17

0x03 0x14 0x00 0x00 0x00 0x14 0x05 0x14 0x00 0x03 0x00 0x00 0x00 0x00

0x03 0x14 0x00 0x00 0x00 0x14 0x05 0x14 0x00 0x03 0x00 0x00 0x00 0x01

0x03 0x14 0x00 0x00 0x00 0x14 0x05 0x14 0x00 0x03 0x00 0x00 0x00 0x02

0x03 0x14 0x00 0x00 0x00 0x14 0x05 0x14 0x00 0x03 0x00 0x00 0x00 0x03

0x03 0x14 0x00 0x00 0x00 0x14 0x05 0x14 0x00 0x03 0x00 0x00 0x00 0x04

0x03 0x14 0x00 0x00 0x00 0x14 0x05 0x14 0x00 0x03 0x00 0x00 0x00 0x05

0x05 0x14 0x00 0x03 0x00 0x00 0x00 0x00 0x17

0x03 0x14 0x00 0x00 0x00 0x14 0x05 0x14 0x00 0x03 0x00 0x00 0x00 0x00

0x03 0x14 0x00 0x00 0x00 0x14 0x05 0x14 0x00 0x03 0x00 0x00 0x00 0x01

0x05 0x14 0x00 0x03 0x00 0x00 0x00 0x00 0x17

0x03 0x14 0x00 0x00 0x00 0x14

0x05 0x14 0x00 0x04 0x00 0x00 0x00 0x00 0x00 0x18

0x03 0x14 0x00 0x00 0x00 0x14

0x05 0x14 0x00 0x04 0x00 0x00 0x00 0x32 0x00 0x4A

0x03 0x14 0x00 0x00 0x00 0x14 0x05 0x14 0x00 0x03 0x00 0x00 0x00 0x00

0x03 0x14 0x00 0x00 0x00 0x14 0x05 0x14 0x00 0x03 0x00 0x00 0x00 0x02

0x03 0x14 0x00 0x00 0x00 0x14 0x05 0x14 0x00 0x03 0x00 0x00 0x00 0x03

0x03 0x14 0x00 0x00 0x00 0x14 0x05 0x14 0x00 0x03 0x00 0x00 0x00 0x04

0x03 0x14 0x00 0x00 0x00 0x14 0x05 0x14 0x00 0x03 0x00 0x00 0x00 0x09

0x17

0x18

0x19

0x1A

0x17

0x18

0x19

0x1A

0x1B

0x1C

0x17

0x18

Refer to value mapping table 3.2.2 (2 byte)

0x17

0x19

0x1A

0x1B

0x20

Aspect ratio Read Get Value 0x07 0x14 0x00 0x05 0x00 0x34 0x00

Auto Adjust Write Execute 0x06 0x14 0x00 0x04 0x00 0x34 0x12

position

0x31 0x00 0x90

0x00 0x12 0x04 0x63

0x05 0x00 0x63

0x06 0x01 0x65

0x05 0x14 0x00 0x03 0x00 0x00 0x00 0x00 0x17

0x03 0x14 0x00 0x00 0x00 0x14 Note 6.

6165

No. Function Type Action Command Response The response of Query Read command

Color mode

Write

Standard

0x06 0x14 0x00 0x04 0x00 0x34 0x12

0x03 0x14 0x00 0x00 0x00 0x14

0x05 0x14 0x00 0x03 0x00 0x00 0x00 0x04

Color mode

Read

Status

0x07 0x14 0x00 0x05 0x00 0x34 0x00

0x05 0x14 0x00 0x03 0x00 0x00

Primary

Write M 0x06 0x14 0x00 0x04 0x00 0x34 0x12

0x03 0x14 0x00 0x00 0x00 0x14

0x05 0x14 0x00 0x03 0x00 0x00 0x00 0x04

Horizontal position

Vertical position

Color

emperature

Color

emperature

Color

emperature

Color

emperature

Blank Write ON 0x06 0x14 0x00 0x04 0x00 0x34 0x12

Blank Write OFF 0x06 0x14 0x00 0x04 0x00 0x34 0x12 t

Blank Read Status 0x07 0x14 0x00 0x05 0x00 0x34 0x00 t

Keystone-V ertical

Keystone-H orizontal

Color mode Write Brightest 0x06 0x14 0x00 0x04 0x00 0x34 0x12

Color mode Write Movie 0x06 0x14 0x00 0x04 0x00 0x34 0x12

Color mode Write Photo 0x06 0x14 0x00 0x04 0x00 0x34 0x12

Color mode Write Presentation 0x06 0x14 0x00 0x04 0x00 0x34 0x12

Reset

current color settings

Primary Color

Color

Write Shift Left 0x06 0x14 0x00 0x04 0x00 0x34 0x12

0x06 0x00 0x64

Read Get Value 0x07 0x14 0x00 0x05 0x00 0x34 0x00

0x00 0x12 0x06 0x65

Write Shift Up 0x06 0x14 0x00 0x04 0x00 0x34 0x12

0x07 0x00 0x65

Write Shift Down 0x06 0x14 0x00 0x04 0x00 0x34 0x12

0x07 0x01 0x66

Read Get Value 0x07 0x14 0x00 0x05 0x00 0x34 0x00

0x00 0x12 0x07 0x66

Write Warm 0x06 0x14 0x00 0x04 0x00 0x34 0x12

0x08 0x00 0x66

Write Normal 0x06 0x14 0x00 0x04 0x00 0x34 0x12

0x08 0x01 0x67

Write Cool 0x06 0x14 0x00 0x04 0x00 0x34 0x12

0x08 0x03 0x69

Read Get Value 0x07 0x14 0x00 0x05 0x00 0x34 0x00

0x00 0x12 0x08 0x67

0x09 0x01 0x68

0x09 0x00 0x67

0x00 0x12 0x09 0x68

Write Decrease 0x06 0x14 0x00 0x04 0x00 0x34 0x12

0x0A 0x00 0x68

Write Increase 0x06 0x14 0x00 0x04 0x00 0x34 0x12

0x0A 0x01 0x69

Read Get value 0x07 0x14 0x00 0x05 0x00 0x34 0x00

0x00 0x12 0x0A 0x69

Write Decrease 0x06 0x14 0x00 0x04 0x00 0x34 0x11

0x31 0x00 0x8E

Write Increase 0x06 0x14 0x00 0x04 0x00 0x34 0x11

0x31 0x01 0x8F

Read Get value 0x07 0x14 0x00 0x05 0x00 0x34 0x00

0x00 0x11 0x31 0x8F

0x0B 0x00 0x69

0x0B 0x01 0x6A

0x0B 0x04 0x6D

0x0B 0x13 0x7C

0x0B 0x14 0x7D

0x00 0x12 0x0B 0x6A

Write Reset 0x06 0x14 0x00 0x04 0x00 0x34 0x11

0x2A 0x00 0x87

Write R 0x06 0x14 0x00 0x04 0x00 0x34 0x12

0x10 0x00 0x6E

Write G 0x06 0x14 0x00 0x04 0x00 0x34 0x12

0x10 0x01 0x6F

Write B 0x06 0x14 0x00 0x04 0x00 0x34 0x12

0x10 0x02 0x70

Write C 0x06 0x14 0x00 0x04 0x00 0x34 0x12

0x10 0x03 0x71

0x10 0x04 0x72

0x03 0x14 0x00 0x00 0x00 0x14

0x05 0x14 0x00 0x03 0x00 0x00 0x00 0x00 0x17

0x03 0x14 0x00 0x00 0x00 0x14

0x05 0x14 0x00 0x03 0x00 0x00 0x00 0x00 0x17

0x03 0x14 0x00 0x00 0x00 0x14 0x05 0x14 0x00 0x03 0x00 0x00 0x00 0x00

0x03 0x14 0x00 0x00 0x00 0x14 0x05 0x14 0x00 0x03 0x00 0x00 0x00 0x01

0x03 0x14 0x00 0x00 0x00 0x14 0x05 0x14 0x00 0x03 0x00 0x00 0x00 0x03

0x05 0x14 0x00 0x03 0x00 0x00 0x00 0x00 0x17

0x03 0x14 0x00 0x00 0x00 0x14 0x05 0x14 0x00 0x03 0x00 0x00 0x00 0x01

0x03 0x14 0x00 0x00 0x00 0x14 0x05 0x14 0x00 0x03 0x00 0x00 0x00 0x00

0x05 0x14 0x00 0x03 0x00 0x00 0x00 0x00 0x17

0x03 0x14 0x00 0x00 0x00 0x14

0x05 0x14 0x00 0x03 0x00 0x00 0x00 0x00 0x17

0x03 0x14 0x00 0x00 0x00 0x14

0x05 0x14 0x00 0x03 0x00 0x00 0x00 0x00 0x17

0x03 0x14 0x00 0x00 0x00 0x14 0x05 0x14 0x00 0x03 0x00 0x00 0x00 0x00

0x03 0x14 0x00 0x00 0x00 0x14 0x05 0x14 0x00 0x03 0x00 0x00 0x00 0x08

0x03 0x14 0x00 0x00 0x00 0x14 0x05 0x14 0x00 0x03 0x00 0x00 0x00 0x13

0x03 0x14 0x00 0x00 0x00 0x14 0x05 0x14 0x00 0x03 0x00 0x00 0x00 0x14

0x00 0x00 0x17

0x03 0x14 0x00 0x00 0x00 0x14

0x03 0x14 0x00 0x00 0x00 0x14 0x05 0x14 0x00 0x03 0x00 0x00 0x00 0x00

0x03 0x14 0x00 0x00 0x00 0x14 0x05 0x14 0x00 0x03 0x00 0x00 0x00 0x01

0x03 0x14 0x00 0x00 0x00 0x14 0x05 0x14 0x00 0x03 0x00 0x00 0x00 0x02

0x03 0x14 0x00 0x00 0x00 0x14 0x05 0x14 0x00 0x03 0x00 0x00 0x00 0x03

Refer to value mapping table 3.2.1 (1byte)

0x17

0x18

0x1A

0x18

0x17

Refer to value mapping table 3.2.1 (1byte)

0x17

0x1F

0x1B

0x2A

0x2B

0x17

0x18

0x19

0x1A

0x1B

No. Function Type Action Command Response The response of Query Read command

100

104

106

107

109

110

112

113

Primary

Write Y 0x06 0x14 0x00 0x04 0x00 0x34 0x12

0x03 0x14 0x00 0x00 0x00 0x14

0x05 0x14 0x00 0x03 0x00 0x00 0x00 0x05

Source input

Write

HDMI 1

0x06 0x14 0x00 0x04 0x00 0x34 0x13

0x03 0x14 0x00 0x00 0x00 0x14

0x05 0x14 0x00 0x03 0x00 0x00 0x00 0x03

Source input

Read

Status

0x07 0x14 0x00 0x05 0x00 0x34 0x00

0x05 0x14 0x00 0x03 0x00 0x00

Color

Primary Color

Hue / Tint Write Decrease 0x06 0x14 0x00 0x04 0x00 0x34 0x12

Hue / Tint Write Increase 0x06 0x14 0x00 0x04 0x00 0x34 0x12

Hue / Tint Read Get value 0x07 0x14 0x00 0x05 0x00 0x34 0x00

Saturation Write Decrease 0x06 0x14 0x00 0x04 0x00 0x34 0x12

Saturation Write Increase 0x06 0x14 0x00 0x04 0x00 0x34 0x12

Saturation Read Get value 0x07 0x14 0x00 0x05 0x00 0x34 0x00

Gain Write Decrease 0x06 0x14 0x00 0x04 0x00 0x34 0x12

Gain Write Increase 0x06 0x14 0x00 0x04 0x00 0x34 0x12

Gain Read Get value 0x07 0x14 0x00 0x05 0x00 0x34 0x00

Sharpness Write Decrease 0x06 0x14 0x00 0x04 0x00 0x34 0x12

Sharpness Write Increase 0x06 0x14 0x00 0x04 0x00 0x34 0x12

Sharpness Read Get value 0x07 0x14 0x00 0x05 0x00 0x34 0x00

Freeze Write ON 0x06 0x14 0x00 0x04 0x00 0x34 0x13

Freeze Write OFF 0x06 0x14 0x00 0x04 0x00 0x34 0x13

Freeze Read Status 0x07 0x14 0x00 0x05 0x00 0x34 0x00

101

Read Status 0x07 0x14 0x00 0x05 0x00 0x34 0x00

0x10 0x05 0x73

0x00 0x12 0x10 0x6F

0x11 0x00 0x6F

0x11 0x01 0x70

0x00 0x12 0x11 0x70

0x12 0x00 0x70

0x12 0x01 0x71

0x00 0x12 0x12 0x71

0x13 0x00 0x71

0x13 0x01 0x72

0x00 0x12 0x13 0x72

0x0E 0x00 0x6C

0x0E 0x01 0x6D

0x00 0x12 0x0E 0x6D

0x00 0x01 0x60

0x00 0x00 0x5F

0x00 0x13 0x00 0x60

0x1C

0x05 0x14 0x00 0x04 0x00 0x00 0x00 0x00 0x00 0x18

0x03 0x14 0x00 0x00 0x00 0x14

0x05 0x14 0x00 0x04 0x00 0x00 0x00 0x00 0x00 0x18

0x03 0x14 0x00 0x00 0x00 0x14

0x05 0x14 0x00 0x04 0x00 0x00 0x00 0x00 0x00 0x18

0x03 0x14 0x00 0x00 0x00 0x14

0x05 0x14 0x00 0x04 0x00 0x00 0x00 0x00 0x00 0x18

0x03 0x14 0x00 0x00 0x00 0x14

0x05 0x14 0x00 0x04 0x00 0x00 0x00 0x00 0x00 0x18

0x03 0x14 0x00 0x00 0x00 0x14 0x05 0x14 0x00 0x03 0x00 0x00 0x00 0x01

0x03 0x14 0x00 0x00 0x00 0x14 0x05 0x14 0x00 0x03 0x00 0x00 0x00 0x00

0x05 0x14 0x00 0x03 0x00 0x00 0x00 0x00 0x17

Refer to value mapping table 3.2.2 (2 byte)

0x18

0x17

Refer to value mapping table 3.2.1 (1byte)

Source input Write D-Sub / Comp.

102

103

Source input Write D-Sub / Comp. 2 0x06 0x14 0x00 0x04 0x00 0x34 0x13

Source input Write HDMI 2 0x06 0x14 0x00 0x04 0x00 0x34 0x13

105

Source input Write Composite

ource input Write S-Video 0x06 0x14 0x00 0x04 0x00 0x34 0x13

108

Quick Auto Search

Quick Auto

111

Mute Write ON 0x06 0x14 0x00 0x04 0x00 0x34 0x14

Mute Write OFF 0x06 0x14 0x00 0x04 0x00 0x34 0x14

Mute Read Status 0x07 0x14 0x00 0x05 0x00 0x34 0x00

114

Video

Write ON 0x06 0x14 0x00 0x04 0x00 0x34 0x13

Write OFF 0x06 0x14 0x00 0x04 0x00 0x34 0x13

Read Status 0x07 0x14 0x00 0x05 0x00 0x34 0x00

0x06 0x14 0x00 0x04 0x00 0x34 0x13 0x01 0x00 0x60

0x01 0x08 0x68

0x01 0x03 0x63

0x01 0x07 0x67

0x06 0x14 0x00 0x04 0x00 0x34 0x13 0x01 0x05 0x65

0x01 0x06 0x66

0x00 0x13 0x01 0x61

0x02 0x01 0x62

0x02 0x00 0x61

0x00 0x13 0x02 0x62

0x00 0x01 0x61

0x00 0x00 0x60

0x00 0x14 0x00 0x61

0x03 0x14 0x00 0x00 0x00 0x14 0x05 0x14 0x00 0x03 0x00 0x00 0x00 0x00

0x03 0x14 0x00 0x00 0x00 0x14 0x05 0x14 0x00 0x03 0x00 0x00 0x00 0x08

0x03 0x14 0x00 0x00 0x00 0x14 0x05 0x14 0x00 0x03 0x00 0x00 0x00 0x07

0x03 0x14 0x00 0x00 0x00 0x14 0x05 0x14 0x00 0x03 0x00 0x00 0x00 0x05

0x03 0x14 0x00 0x00 0x00 0x14 0x05 0x14 0x00 0x03 0x00 0x00 0x00 0x06

0x00 0x00 0x17

0x03 0x14 0x00 0x00 0x00 0x14 0x05 0x14 0x00 0x03 0x00 0x00 0x00 0x01

0x03 0x14 0x00 0x00 0x00 0x14 0x05 0x14 0x00 0x03 0x00 0x00 0x00 0x00

0x05 0x14 0x00 0x03 0x00 0x00 0x00 0x01 0x18

0x03 0x14 0x00 0x00 0x00 0x14 0x05 0x14 0x00 0x03 0x00 0x00 0x00 0x01

0x03 0x14 0x00 0x00 0x00 0x14 0x05 0x14 0x00 0x03 0x00 0x00 0x00 0x00

0x05 0x14 0x00 0x03 0x00 0x00 0x00 0x00 0x17

0x17

0x1F

0x1A

0x1E

0x1C

0x1D

0x18

0x17

0x18

0x17

Note 6.

6367

No. Function Type Action Command Response The response of Query Read command

117

120

123

126

129

132

135

138

141

144

Volume

Write

Write Value

0x06 0x14 0x00 0x04 0x00 0x34 0x13

0x03 0x14 0x00 0x00 0x00 0x14

Language

Write

Français

0x06 0x14 0x00 0x04 0x00 0x34 0x15

0x03 0x14 0x00 0x00 0x00 0x14

0x05 0x14 0x00 0x03 0x00 0x00 0x00 0x01

Language

Write

Español

0x06 0x14 0x00 0x04 0x00 0x34 0x15

0x03 0x14 0x00 0x00 0x00 0x14

0x05 0x14 0x00 0x03 0x00 0x00 0x00 0x04

Language

Write

0x06 0x14 0x00 0x04 0x00 0x34 0x15

0x03 0x14 0x00 0x00 0x00 0x14

0x05 0x14 0x00 0x03 0x00 0x00 0x00 0x07

Language

Write

Swidish

0x06 0x14 0x00 0x04 0x00 0x34 0x15

0x03 0x14 0x00 0x00 0x00 0x14

0x05 0x14 0x00 0x03 0x00 0x00 0x00 0x0A

Language

Write

Czech

0x06 0x14 0x00 0x04 0x00 0x34 0x15

0x03 0x14 0x00 0x00 0x00 0x14

0x05 0x14 0x00 0x03 0x00 0x00 0x00 0x0D

Language

Write

Polish

0x06 0x14 0x00 0x04 0x00 0x34 0x15

0x03 0x14 0x00 0x00 0x00 0x14

0x05 0x14 0x00 0x03 0x00 0x00 0x00 0x10

Language

Write

Vie

0x06 0x14 0x00 0x04 0x00 0x34 0x15

0x03 0x14 0x00 0x00 0x00 0x14

0x05 0x14 0x00 0x03 0x00 0x00 0x00 0x15

Volume Write Increse 0x06 0x14 0x00 0x04 0x00 0x34 0x14

115

Volume Write Decrese 0x06 0x14 0x00 0x04 0x00 0x34 0x14

116

118

Volume Read Get Value 0x07 0x14 0x00 0x05 0x00 0x34 0x00

Language Write English 0x06 0x14 0x00 0x04 0x00 0x34 0x15

119

0x01 0x00 0x61

0x02 0x00 0x62

0x2A 0x11 0x9A

0x00 0x14 0x03 0x64

0x00 0x00 0x61

0x03 0x14 0x00 0x00 0x00 0x14

0x05 0x14 0x00 0x03 0x00 0x00 0x00 0x01 0x18

0x03 0x14 0x00 0x00 0x00 0x14 0x05 0x14 0x00 0x03 0x00 0x00 0x00 0x00

Refer to value mapping table 3.2.1 (1byte)

0x17

0x00 0x01 0x62

121

Language Write Deutsch 0x06 0x14 0x00 0x04 0x00 0x34 0x15

Language Write Italiano 0x06 0x14 0x00 0x04 0x00 0x34 0x15

122

Language Write РУССКИЙ 0x06 0x14 0x00 0x04 0x00 0x34 0x15

124

Language Write

125

Language Write

127

Language Write

128

Language Write Dutch 0x06 0x14 0x00 0x04 0x00 0x34 0x15

130

Language Write Turkish 0x06 0x14 0x00 0x04 0x00 0x34 0x15

131

Language Write Portugese 0x06 0x14 0x00 0x04 0x00 0x34 0x15

133

Language Write Thai 0x06 0x14 0x00 0x04 0x00 0x34 0x15

134

繁體中文

简体中文

日本語

한국어

0x00 0x02 0x63

0x00 0x03 0x64

0x00 0x04 0x65

0x00 0x05 0x66

0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x06 0x67

0x00 0x07 0x68

0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x08 0x69

0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x09 0x6A

0x00 0x0a 0x6B

0x00 0x0b 0x6C

0x00 0x0c 0x6D

0x00 0x0d 0x6E

0x00 0x0e 0x6F

0x00 0x0f 0x70

0x18

0x03 0x14 0x00 0x00 0x00 0x14 0x05 0x14 0x00 0x03 0x00 0x00 0x00 0x02

0x19

0x03 0x14 0x00 0x00 0x00 0x14 0x05 0x14 0x00 0x03 0x00 0x00 0x00 0x03

0x1A

0x1B

0x03 0x14 0x00 0x00 0x00 0x14 0x05 0x14 0x00 0x03 0x00 0x00 0x00 0x05

0x1C

0x03 0x14 0x00 0x00 0x00 0x14 0x05 0x14 0x00 0x03 0x00 0x00 0x00 0x06

0x1D

0x1E

0x03 0x14 0x00 0x00 0x00 0x14 0x05 0x14 0x00 0x03 0x00 0x00 0x00 0x08

0x1F

0x03 0x14 0x00 0x00 0x00 0x14 0x05 0x14 0x00 0x03 0x00 0x00 0x00 0x09

0x20

0x21

0x03 0x14 0x00 0x00 0x00 0x14 0x05 0x14 0x00 0x03 0x00 0x00 0x00 0x0B

0x22

0x03 0x14 0x00 0x00 0x00 0x14 0x05 0x14 0x00 0x03 0x00 0x00 0x00 0x0C

0x23

0x24

0x03 0x14 0x00 0x00 0x00 0x14 0x05 0x14 0x00 0x03 0x00 0x00 0x00 0x0E

0x25

0x03 0x14 0x00 0x00 0x00 0x14 0x05 0x14 0x00 0x03 0x00 0x00 0x00 0x0F

0x26

Language Write Finnish 0x06 0x14 0x00 0x04 0x00 0x34 0x15

136

Language Write Arabic 0x06 0x14 0x00 0x04 0x00 0x34 0x15

137

Language Write Indonesia 0x06 0x14 0x00 0x04 0x00 0x34 0x15

Language Write Hindi 0x06 0x14 0x00 0x04 0x00 0x34 0x15

139

140

Language Read Status 0x07 0x14 0x00 0x05 0x00 0x34 0x00

142

HDMI Format

143

HDMI Format

Write RGB 0x06 0x14 0x00 0x04 0x00 0x34 0x11

Write YUV 0x06 0x14 0x00 0x04 0x00 0x34 0x11

Write Auto 0x06 0x14 0x00 0x04 0x00 0x34 0x11

0x00 0x10 0x71

0x00 0x11 0x72

0x00 0x12 0x73

0x00 0x13 0x74

0x00 0x14 0x75

0x00 0x15 0x76

0x00 0x15 0x00 0x62

0x28 0x00 0x85

0x28 0x01 0x86

0x28 0x02 0x87

0x27

0x03 0x14 0x00 0x00 0x00 0x14 0x05 0x14 0x00 0x03 0x00 0x00 0x00 0x11

0x03 0x14 0x00 0x00 0x00 0x14 0x05 0x14 0x00 0x03 0x00 0x00 0x00 0x12

0x03 0x14 0x00 0x00 0x00 0x14 0x05 0x14 0x00 0x03 0x00 0x00 0x00 0x13

0x03 0x14 0x00 0x00 0x00 0x14 0x05 0x14 0x00 0x03 0x00 0x00 0x00 0x14

0x05 0x14 0x00 0x03 0x00 0x00 0x00 0x00 0x17

0x03 0x14 0x00 0x00 0x00 0x14 0x05 0x14 0x00 0x03 0x00 0x00 0x00 0x00

0x03 0x14 0x00 0x00 0x00 0x14 0x05 0x14 0x00 0x03 0x00 0x00 0x00 0x01

0x03 0x14 0x00 0x00 0x00 0x14 0x05 0x14 0x00 0x03 0x00 0x00 0x00 0x02

0x28

0x29

0x2A

0x2B

0x2C

0x17

0x18

0x19

No. Function Type Action Command Response The response of Query Read command

145

146

148

151

152

154

155

157

158

160

161

164

166

167

170

172

HDMI

Read

Status

0x07 0x14 0x00 0x05 0x00 0x34 0x00

0x05 0x14 0x00 0x03 0x00 0x00

HDMI

Write

Auto

0x06 0x14 0x00 0x04 0x00 0x34 0x11

0x03 0x14 0x00 0x00 0x00 0x14

0x05 0x14 0x00 0x03 0x00 0x00 0x00 0x02

Error status

Read

Status

0x07 0x14 0x00 0x05 0x00 0x34 0x00

0x05 0x14 0x00 0x16 0x00 0x00 0x00

Remote

Write

code 6

0x06 0x14 0x00 0x04 0x00 0x34 0x0C

0x03 0x14 0x00 0x00 0x00 0x14

0x05 0x14 0x00 0x03 0x00 0x00 0x00 0x05

Format

HDMI Range

147

HDMI Range

Range

HDMI

149

Range

CEC Write OFF 0x06 0x14 0x00 0x04 0x00 0x34 0x11

150

CEC Write ON 0x06 0x14 0x00 0x04 0x00 0x34 0x11

CEC Read Status 0x07 0x14 0x00 0x05 0x00 0x34 0x00

153

Brilliant Color

Brilliant

156

Color

Brilliant Color

Brilliant

159

Color

Brilliant Color

162

Brilliant Color

163

Brilliant Color

165

Brilliant Color

Remote Control Code Remote Control Code

168

Remote Control Code Remote

169

Control Code Remote Control Code

171

Control Code Remote Control Code

Write Enhanced 0x06 0x14 0x00 0x04 0x00 0x34 0x11

Write Normal 0x06 0x14 0x00 0x04 0x00 0x34 0x11

Read Status 0x07 0x14 0x00 0x05 0x00 0x34 0x00

Write OFF 0x06 0x14 0x00 0x04 0x00 0x34 0x12

Write Color 1 0x06 0x14 0x00 0x04 0x00 0x34 0x12

Write Color 2 0x06 0x14 0x00 0x04 0x00 0x34 0x12

Write Color 3 0x06 0x14 0x00 0x04 0x00 0x34 0x12

Write Color 4 0x06 0x14 0x00 0x04 0x00 0x34 0x12

Write Color 5 0x06 0x14 0x00 0x04 0x00 0x34 0x12

Write Color 6 0x06 0x14 0x00 0x04 0x00 0x34 0x12

Write Color 7 0x06 0x14 0x00 0x04 0x00 0x34 0x12

Write Color 8 0x06 0x14 0x00 0x04 0x00 0x34 0x12

Write Color 9 0x06 0x14 0x00 0x04 0x00 0x34 0x12

Write Color 10 0x06 0x14 0x00 0x04 0x00 0x34 0x12

Read Status 0x07 0x14 0x00 0x05 0x00 0x34 0x00

Write code 1 0x06 0x14 0x00 0x04 0x00 0x34 0x0C

Write code 2 0x06 0x14 0x00 0x04 0x00 0x34 0x0C

Write code 3 0x06 0x14 0x00 0x04 0x00 0x34 0x0C

Write code 4 0x06 0x14 0x00 0x04 0x00 0x34 0x0C

Write code 5 0x06 0x14 0x00 0x04 0x00 0x34 0x0C

Write code 7 0x06 0x14 0x00 0x04 0x00 0x34 0x0C

0x00 0x11 0x28 0x86

0x29 0x00 0x86

0x29 0x01 0x87

0x29 0x02 0x88

0x00 0x11 0x29 0x87

0x2B 0x00 0x88

0x2B 0x01 0x89

0x00 0x11 0x2B 0x89

0x00 0x0C 0x0D 0x66

0x0F 0x00 0x6D

0x0F 0x01 0x6E

0x0F 0x02 0x6F

0x0F 0x03 0x70

0x0F 0x04 0x71

0x0F 0x05 0x72

0x0F 0x06 0x73

0x0F 0x07 0x74

0x0F 0x08 0x75

0x0F 0x09 0x76

0x0F 0x0A 0x77

0x00 0x12 0x0F 0x6E

0x48 0x00 0xA0

0x48 0x01 0xA1

0x48 0x02 0xA2

0x48 0x03 0xA3

0x48 0x04 0xA4

0x48 0x05 0xA5

0x48 0x06 0xA6

0x00 0x00 0x17

0x03 0x14 0x00 0x00 0x00 0x14 0x05 0x14 0x00 0x03 0x00 0x00 0x00 0x00

0x03 0x14 0x00 0x00 0x00 0x14 0x05 0x14 0x00 0x03 0x00 0x00 0x00 0x01

0x05 0x14 0x00 0x03 0x00 0x00 0x00 0x00 0x17

0x03 0x14 0x00 0x00 0x00 0x14 0x05 0x14 0x00 0x03 0x00 0x00 0x00 0x00

0x03 0x14 0x00 0x00 0x00 0x14 0x05 0x14 0x00 0x03 0x00 0x00 0x00 0x01

0x05 0x14 0x00 0x03 0x00 0x00 0x00 0x00 0x17

0x01 0x02 0x03 0x04 0x05 0x06 0x07 0x08 0x09 0x0A 0x0B 0x0C 0x0D 0x0E 0x0F 0x10 0x11 0x01 0x02 0x03 0x04 0x01 0x01 0x02 0xFF