ViewSonic LS600W operation manual

Page 1

LS600W

Projector User Guide

IMPORTANT: Please read this User Guide to obtain important information on installing and using your product in a safe manner, as well as registering your product for future service. Warranty information contained in this

User Guide will describe your limited coverage from ViewSonic Corporation, which is also found on our web site at

http://www.viewsonic.com in English, or in specific languages using the Regional selection box in the upper right

corner of our website. “Antes de operar su equipo lea cu idadosamente las instrucciones en este manual”

Model No. VS18176

Model Name: LS600W

Page 2

Thank you for choosing ViewSonic®

As a world-leading provider of visual soluons, ViewSonic® is dedicated to exceeding the world’s expectaons for technological evoluon, innovaon, and simplicity. At ViewSonic®, we believe that our products have the potenal to make a posive impact in the world, and we are condent that the ViewSonic® product you have chosen will serve you well.

Once again, thank you for choosing ViewSonic®!

Page 3

Safety Precautions - General

Please read the following Safety Precautions before you start using the projector.

• Keep this user guide in a safe place for later reference.

• Read all warnings and follow all instructions.

• Allow at least 20“ (50 cm) clearance around the projector to ensure proper ventilation.

• Place the projector in a well-ventilated area. Do not place anything on the projector that prevents heat dissipation.

• Do not place the projector on an uneven or unstable surface. The projector may fall over, causing personal injury or projector malfunction.

• Do not use if the projector is tilted at an angle of more than 10° degrees left or

right, nor at an angle of more than 15° degrees forwards or backwards.

• Do not look straight at the projector lens during operation. The intense light beam may damage your eyes.

• Always open the lens shutter or remove the lens cap when the projector light source is on.

• Do not block the projection lens with any objects when the projector is under operation as this could cause objects to become heated and deformed or even cause a fire.

• The light source becomes extremely hot during operation. Allow the projector to cool for approximately 45 minutes prior to removing the light source assembly for replacement.

• Do not use light sources beyond the rated light source life. Excessive use of light

sources beyond the rated life could cause them to break on rare occasions.

• Never replace the light source assembly or any electronic component unless the projector is unplugged.

• Do not attempt to disassemble the projector. There are dangerous high voltages inside which may cause death if you should come into contact with live parts.

• When moving the projector, be careful not to drop or bump the projector on anything.

• Do not place any heavy objects on the projector or connection cables.

• Do not stand the projector on end vertically. Doing so may cause the projector to fall over, causing personal injury or projector malfunction.

• Avoid exposing the projector to direct sunlight or other sources of sustained heat. Do not install near any heat sources such as radiators, heat registers, stoves, or other devices (including amplifiers) that may increase the temperature of the projector to dangerous levels.

• Do not place liquids near or on the projector. Liquids spilled into the projector may cause it to fail. If the projector does become wet, disconnect it from the power supply and call your local service center to have the projector serviced.

Page 4

• When the projector is under operation, you may sense some heated air and odor from its ventilation grill. It is a normal operation and not a defect.

• Do not attempt to circumvent the safety provisions of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding-type plug has two blades and a third grounding prong. The wide and third blade are provided for your safety. If the plug does not fit into your outlet, obtain an adapter and do not attempt to force the plug into the outlet.

• When connecting to a power outlet, DO NOT remove the grounding prong. Please ensure grounding prongs are NEVER REMOVED.

• Protect the power cord from being treaded upon or pinched, particularly at the plug, and at the point where it emerges from the projector.

• In some countries, the voltage is NOT stable. This projector is designed to operate safely within a voltage between 100 to 240 volts AC, but could fail if power cuts or surges of ±10 volts occur. In areas where voltage may fluctuate or cut out, it is recommended that you connect your projector through a power stabilizer, surge protector, or uninterruptable power supply (UPS).

• If smoke, an abnormal noise, or a strange odor is present, immediately switch

the projector off and call your dealer or ViewSonic®. It is dangerous to continue

using the projector.

• Use only attachments/accessories specified by the manufacturer.

• Disconnect the power cord from the AC outlet if the projector is not being used for a long period of time.

• Refer all servicing to qualified service personnel.

CAUTION: Possibly hazardous optical radiation is emitted from this product. As

with any bright light source, do not stare into the beam, RG2 IEC 62471-5:2015.

Page 5

Safety Precautions - Ceiling Mounting

Please read the following Safety Precautions before you start using the projector.

If you intend to mount the projector on the ceiling, we strongly recommend

that you use a proper fitting projector ceiling mount kit and that you ensure it is

securely and safely installed.

If you use an inappropriate projector ceiling mount kit, there is a safety risk that the

projector may fall from the ceiling due to an improper attachment through the use of the wrong gauge or length screws.

You can purchase a projector ceiling mount kit from the place you purchased your

projector. We recommend that you also purchase a separate security cable and

attach it securely to both the anti-theft lock slot on the projector and the base of the ceiling mount bracket. This will perform the secondary role of restraining the projector should its attachment to the mounting bracket become loose.

Page 6

Contents

Safety Precautions - General ....................................... 3

Introduction .............................................................. 10

Features ................................................................................................................ 10

Package Contents .................................................................................................10

Product Overview ................................................................................................. 11

Projector ................................................................................................................ 11

Controls and Functions ............................................................................................... 11

Connection Ports ......................................................................................................... 12

Remote Control ..................................................................................................... 13

Controls and Functions ............................................................................................... 13

Remote Control Effective Range ................................................................................. 14

Replacing the Remote Control Batteries ..................................................................... 14

Initial Setup ............................................................... 15

Choosing a Location ..............................................................................................15

Projection Dimensions ..........................................................................................16

16:10 Image on a 16:10 Screen ................................................................................... 16

16:10 Image on a 4:3 Screen ....................................................................................... 17

Mounting the Projector ........................................................................................ 18

Preventing Unauthorized Use...............................................................................19

Using the Security Slot .......................................................................................... 19

Using the Password Function ................................................................................ 20

Setting a Password ...................................................................................................... 20

Changing the Password ............................................................................................... 21

Disabling the Password Function ................................................................................ 21

Forgetting the Password ............................................................................................. 22

Password Recall Procedure ......................................................................................... 22

Locking the Control Keys ....................................................................................... 22

Page 7

Making Connections .................................................. 23

Connecting to Power ............................................................................................23

Connecting to Video Sources ................................................................................24

HDMI Connection .................................................................................................. 24

Composite Video Connection ................................................................................ 25

Connecting to Computer Sources ......................................................................... 26

VGA Connection .................................................................................................... 26

VGA Out Connection ............................................................................................. 26

Connecting to Audio ............................................................................................. 27

Operation .................................................................. 28

Turning the Projector On/Off ...............................................................................28

Starting Up the Projector ...................................................................................... 28

First Time Activation ................................................................................................... 28

Shutting Down the Projector ................................................................................. 29

Selecting an Input Source .....................................................................................30

Adjusting the Projected Image .............................................................................31

Adjusting the Projector's Height and Projection Angle ............................................... 31

Auto-Adjusting the Image ........................................................................................... 31

Fine-Tuning the Image Size and Clarity ................................................................. 31

Correcting Keystone .............................................................................................. 32

Hiding the Image ..................................................................................................33

Controlling the Projector through a LAN Environment ........................................34

Configuring the LAN Control Settings .................................................................... 34

Controlling the Projector through a Web Browser ............................................... 36

About Crestron e-Control® .................................................................................... 40

PJLink™, SNMP, AMX and Xpanel Formats Supported .......................................... 43

Page 8

Menu Functions ........................................................ 44

General On-Screen Display (OSD) Menu Operation .............................................44

On-Screen Display (OSD) Menu Tree .................................................................... 45

DISPLAY Menu ......................................................................................................50

IMAGE Menu ........................................................................................................53

POWER MANAGEMENT Menu .............................................................................56

BASIC Menu .......................................................................................................... 59

ADVANCED Menu .................................................................................................62

SYSTEM Menu .......................................................................................................66

INFORMATION Menu ...........................................................................................69

Appendix ................................................................... 70

Specifications ........................................................................................................70

Projector Dimensions ............................................................................................ 71

Timing Chart .........................................................................................................71

Analog RGB ............................................................................................................ 71

HDMI (PC) .............................................................................................................. 73

HDMI (Video) ......................................................................................................... 74

Video/S-Video ....................................................................................................... 74

Component video .................................................................................................. 75

IR Control Table ....................................................................................................76

Address Code ........................................................................................................ 77

RS-232 Command Table .......................................................................................78

Pin Assignment ...................................................................................................... 78

Interface ................................................................................................................ 78

Command Table .................................................................................................... 78

Glossary ................................................................................................................87

Troubleshooting ...................................................................................................90

Common Problems ................................................................................................ 90

LED Indicators ........................................................................................................ 91

Maintenance.........................................................................................................92

General Precautions .............................................................................................. 92

Cleaning the Lens .................................................................................................. 92

Cleaning the Case .................................................................................................. 92

Storing the Projector ............................................................................................. 92

Disclaimer .............................................................................................................. 92

Light Source Information ...................................................................................... 93

Light Source Hour .................................................................................................. 93

Extending Light Source Life ................................................................................... 93

Page 9

Regulatory and Service Information .......................... 94

Compliance Information ....................................................................................... 94

FCC Compliance Statement ................................................................................... 94

Industry Canada Statement ................................................................................... 94

CE Conformity for European Countries ................................................................. 94

Declaration of RoHS2 Compliance......................................................................... 95

Indian Restriction of Hazardous Substances ......................................................... 96

Product Disposal at End of Product Life ................................................................ 96

Customer Service .................................................................................................. 98

Limited Warranty .................................................................................................. 99

Mexico Limited Warranty .................................................................................... 102

Page 10

Introduction

The LS600W is a 3,000 ANSI Lumens, high brightness WXGA Lamp Free Projector for business and education. Adopting 2nd generation LED technology, it frees users from frequent lamp replacement and toxic mercury, offers an amazing 30,000 hours long lifespan, true-to-life colors with 125% Rec.709, as well as instant power on/ off for efficient power saving. Its comprehensive LAN control eases multiple device management and is compatible with Crestron, AMX, Extron, PJ Link, ATEN, and ViewSonic’s vController. Enjoy all the amazing features this projector has to offer with hassle-free setup, 360° tilt angle projection, 1.2x zoom lens, H/V Keystone, and 4 Corner adjustment.

Features

• Lamp free, Mercury free, Maintenance free

• 2nd generaon LED Technology with 30,000 hours lifespan

• Instant power on/o

• 3,000 ANSI Lumens oering bright images in any environment

• 360° projecon and H/V keystone for easy installaon

• Cinema SuperColor+™ Technology with 125% Rec.709

• H/V Keystone enabling side projecons

• Comprehensive LAN control for ecient management*

Package Contents

• Projector

• Power Cord

• Video Cable

NOTE: The power cord and video cables included in your package may vary depending

on your country. Please contact your local reseller for more informaon.

• Remote Control & Baeries

• Quick Start Guide

Page 11

Product Overview

EXIT

SOURCE

ENTER

BLANK

COLOR

MODE

Projector

Controls and Functions

Power key

Focus Ring Zoom Ring

Power Indicator Light

Temperature Indicator Light Light Source Indicator Light

Remote IR sensor

Projection Lens

Key Description

[ ] Power

[ / / / ] Keystone Keys

[ / / / ] Left/Right/Up/Down

Menu/Exit Turns on or off the On-Screen Display (OSD) Menu. Source Displays the input source selection bar.

(Help)

Blank Hides the screen picture. Enter Enacts the selected On-Screen Display (OSD) Menu item when

[ ] Corner Adjustment

Color Mode Displays the color mode selection bar.

Toggles the projector between standby mode and Power On.

Manually corrects distorted images resulting from an angled projection.

Selects the desired menu items and makes adjustments when the On-Screen Display (OSD) Menu is activated.

Displays the HELP menu.

the OSD Menu is activated. Displays the Corner Adj. menu when the OSD menu is not

activated.

Page 12

Connection Ports

AUDIO OUTRJ-45AUDIO IN COMPUTER IN VIDE

AC Power Cord Inlet

Ceiling Mount Holes

HDMI 1HDMI 2

5 8

USB 5V/1.5A OUT

(Service)

S-232

Security Slot

Security Bar

Adjuster Foot

Port Description

[1] RJ-45 LAN port. [2] AUDIO OUT Audio signal output socket. [3] AUDIO IN Audio signal input socket. [4] HDMI 1 HDMI port. [5] HDMI 2 HDMI port. [6] COMPUTER IN RGB (PC) signal input socket. [7] VIDEO Composite video port. [8] USB 5V/1.5A OUT (Service) USB Type A port for power supply and serivce. [9] RS-232 RS-232 control port.

1212

Page 13

Remote Control

Controls and Functions

Button

Left/ Right

Up/ Down

Description

Selects the desired menu items and makes adjustments.

Button

On/ Off

COMP

HDMI 1

HDMI 2

Auto Sync

Source

[ / / / ] Keystone Keys

Enter

(Corner

adjustment)

Description

Toggles between standby mode and Power On.

Selects the source from the COMPUTER IN port for display.

Selects the source from the HDMI 1 port for display.

Selects the source from the HDMI 2 port for display.

Automatically determines the best picture timings for the displayed image. Displays the source selection bar. Manually corrects distorted images resulting from an angled projection.

Enacts the selected OSD Menu item.

Displays the Corner Adj. menu when the OSD menu is not activated.

(Laser)

Exit

Aspect

Freeze Pattern

Blank PgUp (Page Up)/

PgDn (Page Down)

(Presentation

Timer) Eco Mode

(Volume Up)

(Volume

Down)

(Mute)

Color Mode

(INFORMATION) Network

Turns on/off the On-Screen Display (OSD) Menu or goes back to previous OSD Menu. Emits visible laser pointer light for presentation purposes.

Exits and saves menu settings.

Displays the aspect ratio selection bar.

Freezes the projected image. Displays embedded test

pattern. Hides the screen picture.

Operates your display software program (on a connected PC) which responds to page up/down commands (like Microsoft PowerPoint).

NOTE: Only available when

a PC input signal is

selected. Displays the Presentation Timer menu.

Selects the Eco mode. Increases the volume level.

Decreases the volume level.

Toggles audio between on and off.

Displays the color mode selection bar. Magnifies the projected picture size.

Reduces the projected picture size.

Displays the INFORMATION menu.

Displays the

LAN Control Settings menu.

Page 14

Remote Control Effective Range

To ensure proper function of the remote control follow the steps below:

Approx. 30°

1. The remote control must be held at an angle

within 30° perpendicular to the projector’s IR remote control sensor(s).

2. The distance between the remote control and

the sensor(s) should not exceed 8 m (26 ft.)

Approx. 30°

NOTE: Refer to the illustration for the location of

the infrared (IR) remote control sensor(s).

Replacing the Remote Control Batteries

1. Remove the battery cover from the rear of the remote control by pressing the

finger grip and sliding it down.

2. Remove any existing batteries (if necessary) and install two AAA batteries.

NOTE: Observe the battery’s polarities as indicated.

3. Replace the battery cover by aligning it with the base and pushing it back into

position.

NOTE:

• Avoid leaving the remote control and batteries in excessive heat or a humid

environment.

• Replace only with the same or equivalent type recommended by the battery

manufacturer.

• Dispose of the used batteries according to the manufacturer’s instructions and

local environment regulations for your region.

• If the batteries are drained or if you will not be using the remote control for an

extended period of time, remove the batteries to avoid damage to the remote control.

Page 15

Initial Setup

This section provides detailed instructions for setting up your projector.

Choosing a Location

Personal preference and room layout will decide the installation location. Consider the following:

• Size and Position of your screen.

• Location of a suitable power outlet.

• Location and Distance between the projector and other equipment.

The projector is designed to be installed in one of the following locations:

1. Front

The projector is placed near the floor in front of the screen.

2. Front Ceiling

The projector is suspeneded upsidedown from the ceiling in front of the screen.

3. Rear Ceiling

The projector is suspended upside-down from the ceiling behind the screen.

NOTE: A special rear projection screen

is required.

4. Rear

The projector is placed near the floor behind the screen.

NOTE: A special rear projection screen

is required.

Page 16

Projection Dimensions

(a)

NOTE: See “Specifications” on page 70 for the native display resolution of this

projector.

• 16:10 Image on a 16:10 Screen

• 16:10 Image on a 4:3 Screen

(e)

(c)

(f)

(d)

(b)

NOTE: (e) = Screen / (f) = Center of Lens

16:10 Image on a 16:10 Screen

(a) Screen

Size

(b) Projection Distance (c) Image

minimum maximum minimum maximum

Height

(d) Vertical Offset

in. mm in. mm in. mm in. mm in. mm in. mm

30 762 35 883 42 1059 16 404 13 319 12.6 319 40 1016 46 1177 56 1412 21 538 17 425 16.7 425 50 1270 58 1471 70 1766 26 673 21 532 20.9 532 60 1524 70 1766 83 2119 32 808 25 638 25.1 638 70 1778 81 2060 97 2472 37 942 29 744 29.3 744 80 2032 93 2354 111 2825 42 1077 33 851 33.5 851

90 2286 104 2648 125 3178 48 1212 38 957 37.7 957 100 2540 116 2943 139 3531 53 1346 42 1063 41.9 1063 120 3048 139 3531 167 4237 64 1615 50 1276 50.2 1276 150 3810 174 4414 209 5297 79 2019 63 1595 62.8 1595 200 5080 232 5885 278 7062 106 2692 84 2127 83.7 2127 250 6350 290 7356 348 8828 132 3365 105 2659 104.7 2659 300 7620 348 8828 417 10593 159 4039 126 3190 125.6 3190

Page 17

16:10 Image on a 4:3 Screen

(a) Screen

Size

(b) Projection Distance (c) Image

minimum maximum minimum maximum

Height

(d) Vertical Offset

in. mm in. mm in. mm in. mm in. mm in. mm

30 762 33 833 39 999 15 381 12 301 12 301

40 1016 44 1110 52 1332 20 508 16 401 16 401

50 1270 55 1388 66 1666 25 635 20 502 20 502

60 1524 66 1666 79 1999 30 762 24 602 24 602

70 1778 77 1943 92 2332 35 889 28 702 28 702

80 2032 87 2221 105 2665 40 1016 32 803 32 803

90 2286 98 2498 118 2998 45 1143 36 903 36 903 100 2540 109 2776 131 3331 50 1270 40 1003 40 1003 120 3048 131 3331 157 3997 60 1524 47 1204 47 1204 150 3810 164 4164 197 4997 75 1905 59 1505 59 1505 200 5080 219 5552 262 6662 100 2540 79 2007 79 2007 250 6350 273 6940 328 8328 125 3175 99 2508 99 2508 300 7620 328 8328 393 9994 150 3810 119 3010 119 3010

NOTE: There is a 3% tolerance among these numbers due to optical component

variations. It is recommended to physically test the projection size and distance before permanently installing the projector.

Page 18

Mounting the Projector

176.6

NOTE: If you buy a third-party mount, please use the correct screw size. Screw size

can vary depending on the thickness of the mounting plate.

1. To ensure the most secure installation, please use a ViewSonic® wall or ceiling

mount.

2. Ensure the screws used to attach a mount to the projector meet the following specifications:

• Screw type: M4

• Screw length: 12.8 mm ~ 15.8 mm

145.6

282.9

305.9

NOTE:

• Avoid installing the projector near a heat source.

• Keep at least a 10 cm gap between the ceiling and the bottom of the

projector.

Page 19

Preventing Unauthorized Use

The projector has several built-in security features to prevent theft, access, or accidental setting changes.

Using the Security Slot

To help prevent the projector from being stolen, use a security slot locking device to secure the projector to a fixed object.

Below is an example of setting up a security slot locking device:

NOTE: The security slot can also be used as a safety anchor if the projector is

mounted to the ceiling.

Page 20

Using the Password Function

To help prevent unauthorized access or use, the projector offers a password security option. The password can be set through the On-Screen Display (OSD) Menu.

NOTE: Make note of your password, and keep it in a safe place.

Setting a Password

1. Press Menu to open the OSD Menu and go to: SYSTEM > Security Settings and

press Enter.

2. Highlight Power On Lock and select

On by pressing / .

3. As pictured to the right, the four

arrow keys ( , , , ) represent 4 digits (1, 2, 3, 4). Press the arrow keys to enter a six digit password.

4. Confirm the new password by re-entering the new password. Once the password is set, the OSD Menu will return to the Security Settings page.

5. Press Exit to leave the OSD Menu.

NOTE: Once set, the correct password must be entered every time the projector is

started.

2020

Page 21

Changing the Password

1. Press Menu to open the OSD Menu and go to: SYSTEM > Security Settings >

Change Password.

2. Press Enter, the message, ‘INPUT CURRENT PASSWORD’ will appear.

3. Enter the old password.

 If the password is correct, the message, ‘INPUT NEW PASSWORD’ will

appear.

 If the password is incorrect, a password error message will appear for 5

seconds followed by the message, ‘INPUT CURRENT PASSWORD’. You can try again or press Exit to cancel.

4. Enter a new password.

5. Confirm the new password by re-entering the new password.

6. To leave the OSD Menu, press Exit.

NOTE: The digits being input will display as asterisks (*).

Disabling the Password Function

1. Press Menu to open the OSD Menu and go to: SYSTEM > Security Settings >

Power On Lock.

2. Press / to select Off.

3. The message, “Input Password” will appear. Enter the current password.

 If the password is correct, the OSD Menu returns to the Password page with

“Off” shown in the row of Power On Lock.

 If the password is incorrect, a password error message will appear for 5

seconds followed by the message, ‘INPUT CURRENT PASSWORD’. You can try again or press Exit to cancel.

NOTE: Please keep the old password, as you will need it to reactivate the password

function.

Page 22

Forgetting the Password

If the password function is activated, you will be asked to enter the six-digit password every time you turn on the projector. If you enter the wrong password, the password error message, as pictured to the right, will appear for 5 seconds, and the message ‘INPUT PASSWORD’ follows.

You can retry or if you do not remember, you can use the “Password Recall Procedure”.

NOTE: If you enter an incorrect password 5 times in succession, the projector will

automatically shut down for a short time.

Password Recall Procedure

1. When the message ‘INPUT CURRENT

PASSWORD’ appears, press and hold Auto Sync for 3 seconds. The projector will display a coded number on the screen.

2. Write down the number and turn off your projector.

3. Seek help from the local service center to decode the number. You may be required to provide proof of purchase documentation to verify that you are an authorized user of the projector.

Locking the Control Keys

With the control keys on the projector locked, you can prevent your settings from being changed accidentally (by children, for example).

NOTE: When the Panel Key Lock is On, no control keys on the projector will operate

except Power.

1. Press Menu to open the OSD Menu and go to: SYSTEM > Panel Key Lock.

2. Press / to select On.

3. Select Yes and press Enter to confirm.

4. To release panel key lock, press and hold on the projector for 3 seconds.

NOTE: You can also use the remote control to enter the SYSTEM > Panel Key Lock

menu and select Off.

2222

Page 23

Making Connections

This section guides you on how to connect the projector with other equipment.

Connecting to Power

1. Connect the power cord to the AC IN jack at the rear of the projector.

2. Plug the power cord into a power outlet.

NOTE: When installing the projector, incorporate a readily accessible disconnect

device in the xed wiring, or connect the power plug to an easily accessible outlet near the unit. If a fault should occur during operaon of the projector, use the disconnect device to switch o the power supply, or disconnect the

power plug.

Page 24

Connecting to Video Sources

HDMI Connection

Connect one end of an HDMI cable to the HDMI port of your video device. Then connect the other end of the cable to the HDMI 1 or HDMI 2 port of your projector.

AUDIOOUTRJ-45AUDIO IN COMPUTER IN VIDE

HDMI 1HDMI2

USB5V/1.5A OUT

(Service)

S-232

Page 25

Composite Video Connection

Connect one end of a Video cable to the Video port of your video device. Then connect the other end of the cable to the VIDEO port of your projector.

AUDIO OUTRJ-45AUDIO IN COMPUTER IN VIDE

HDMI 1HDMI 2

USB 5V/1.5A OUT

(Service)

S-232

Page 26

Connecting to Computer Sources

VGA Connection

Connect one end of a VGA cable to the VGA port of your computer. Then connect the other end of the cable to the COMPUTER IN port of your projector.

NOTE: Some notebooks do not turn on their external displays automacally when

connected to a projector. You may have to adjust your notebook’s projecon sengs.

VGA Out Connection

After establishing the VGA Connection, connect one end of a VGA cable to the VGA port of your monitor. Then connect the other end of the cable to the MONITOR OUT port of your projector.

AUDIO OUTRJ-45AUDIO IN COMPUTER IN VIDE

HDMI 1HDMI 2

USB 5V/1.5A OUT

(Service)

S-232

Page 27

Connecting to Audio

The projector is equipped with speakers, however, you can also connect external

speakers to the AUDIO OUT port of the projector.

NOTE: The audio output is controlled by the projector’s Volume and Mute sengs.

Page 28

Operation

Turning the Projector On/Off

Starting Up the Projector

1. Press the Power buon to turn on the projector.

2. The light source will light up, and a “Power On/O Ring Tone” will play.

3. The Power Indicator Light stays green when the projector is On.

NOTE: To maintain light source life, once you turn the projector On, wait at least ve

(5) minutes before turning it o.

4. Turn on all of the connected equipment, i.e. notebook, and the projector will start to search for an input source.

NOTE: If the projector detects an input source, the source informaon will appear. If

an input source is not detected, the message, ‘No Signal’ will appear.

First Time Activation

If the projector is activated for the first time, select your OSD language following the on-screen instructions.

Page 29

Shutting Down the Projector

1. Press the Power or O buon and a conrmaon message will appear to prompt

you to press the Power or O buon a second me. Addionally you can press any other buon to cancel.

NOTE: If you do not respond in a few seconds aer the rst press, the message will

disappear.

2. Once the cooling process nishes, a “Power On/O Ring Tone” will play.

3. Disconnect the power cord from the power outlet if the projector will not be

used for an extended period of me.

NOTE:

• To protect the light source, the projector will not respond to commands during

the cooling process.

• Do not unplug the power cord before the projector completely shuts down.

Page 30

Selecting an Input Source

The projector can be connected to multiple devices at the same time. However, it can only display one full screen at a time.

If you want the projector to automatically search for the input source, ensure the Quick Auto Search function in the SYSTEM menu is On.

The Input Source can also be manually selected by pressing one of the source selection buttons on the remote control, or by cycling through the available input sources.

To manually select the input source do the following:

1. Press Source, and a source selecon menu will appear.

2. Press / unl your desired signal is selected and press Enter.

3. Once detected, the selected source informaon will be displayed on the screen

for a few seconds.

NOTE: If there are mulple devices connected to the projector, repeat steps 1-2 to

search for another source.

Page 31

Adjusting the Projected Image

Adjusting the Projector's Height and Projection Angle

The projector is equipped with one (1) adjuster foot. Adjusting the foot will change the projector’s height and the vertical projection angle. Carefully adjust the feet to fine tune the projected image’s position.

Auto-Adjusting the Image

Sometimes, you may need to improve the picture quality. To do this, press Auto Sync on the remote control. Within five (5) seconds, the built-in Intelligent Auto

Adjustment function will re-adjust the Frequency and Clock values to provide the best picture quality.

Upon completion, the current source information will appear in the upper left corner for three (3) seconds.

NOTE: This funcon is only available when the PC D-Sub input source (analog RGB/

COMPUTER IN) is selected.

Fine-Tuning the Image Size and Clarity

To adjust the projected image to the size that you need, rotate the Zoom Ring.

To improve the clarity of the image, rotate the Focus Ring.

Page 32

Correcting Keystone

EXIT

SOURCE

ENTER

BLANK

COLOR

MODE

Keystoning refers to the situation where the projected image becomes a trapezoid due to angled projection. To correct this, besides adjusting the height of the projector, you may also:

1. Use the keystone keys on the projector or remote control to display the keystone page.

2. Aer the keystone page is displayed, press to correct keystoning at the top of the image. Press to correct keystoning at the boom of the image. Press to correct keystoning at the right side of the image. Press to correct keystoning at the le side of the image.

Page 33

Hiding the Image

In order to draw the audience’s full attention to the presenter, you can press Blank on the projector or remote control to hide the screen image. Press any key on the projector or remote control to restore the image.

CAUTION: Do not block the projecon lens as this could cause the blocking object to

become heated and deformed or even cause a re.

Page 34

Controlling the Projector through a LAN Environment

The projector supports Crestron® software. With correct settings for the LAN Control Settings menu, you can manage the projector from a computer using a web browser when the computer and the projector are properly connected to the same local area network.

AUDIO OUTRJ-45AUDIO IN COMPUTER IN VIDE

HDMI 1HDMI 2

USB 5V/1.5A OUT

(Service)

S-232

Configuring the LAN Control Settings

• If you are in a DHCP environment:

1. Take a RJ45 cable and connect one end to the RJ45 LAN input jack of the projector and the other end to the RJ45 port.

2. Open the OSD menu and go to the ADVANCED > LAN Control Settings menu. Press Enter to display the LAN Control Settings page. Or you can press Network

to open the LAN Control Settings menu directly.

3. Highlight LAN Settings and press / to select DHCP ON.

4. Press to highlight Apply and press Enter.

5. Please wait for around 15 - 20 seconds, and then re-enter the LAN Settings

page. The Projector IP Address, Subnet Mask, Default Gateway, DNS Server sengs will be displayed. Make note of the IP address displayed in the

Projector IP Address row.

NOTE:

Page 35

• If the Projector IP Address sll does not appear, contact your network

administrator.

• If the RJ45 cables are not properly connected, the Projector IP Address,

Subnet Mask, Default Gateway and DNS Server sengs will display 0.0.0.0. Make

sure the cables are properly connected and perform the procedures above again.

• If you need to connect to the projector in its standby mode, set

Standby LAN Control to On in the ADVANCED > LAN Control Settings menu.

• If you are in a non-DHCP environment:

1. Repeat steps 1-2 above.

2. Highlight LAN Settings and press / to select Static IP.

3. Contact your ITS administrator for informaon on the Projector IP Address,

Subnet Mask, Default Gateway, DNS Server sengs.

4. Press to select the item you want to modify and press Enter.

5. Press / to move the cursor and the press / to enter the value.

6. To save the sengs, press Enter. If you do not want to save the sengs, press

Exit.

7. Press to highlight Apply and press Enter.

NOTE:

• If the RJ45 cables are not properly connected, the Projector IP Address,

Subnet Mask, Default Gateway, DNS Server sengs will display 0.0.0.0. Make

sure the cables are properly connected and perform the procedures above again.

• If you wish to connect to the projector in its standby mode, be sure you

have selected Static IP and obtained the Projector IP Address, Subnet Mask,

Default Gateway and DNS Server informaon when the projector is on.

Page 36

Controlling the Projector through a Web Browser

Once you have the correct IP address for the projector and the projector is on or in standby mode, you can use any computer that is on the same local area network to control the projector.

NOTE:

• If you are using Microso Internet Explorer, make sure it is version 7.0 or higher.

• The screen shots in this manual are for reference only, and may dier from the

actual design.

• Please pay aenon to the limitaon of input length (including space and other

punctuaon keys) in the list below:

Category Item Input Length Maximum Number

of Characters

DHCP/Manual (N/A) IP Address 15

Network

Network Sengs

Password

SNMP

Email Seng

SMTP Seng

Email Alert

Alert Condion

Subnet Mask 15 Gateway 15 DNS Server 15 AMX device discover (N/A) Administrator (N/A) New Password 8 Conrm Password 8 SysLocaon 22 SysName 22 SysContact 22 To 40 Cc 40 Subject 40 From 40 Server 30 User Name 21 Password 14 Fan Error (N/A) Light Source Error (N/A) Over Temperature (N/A) Submit (N/A) Issue Test Mail (N/A)

NOTE: / > < $ % + \ ‘ “ ” ’ are prohibited.

Page 37

1. Enter the address of the projector in the address bar of your browser and press

Enter.

2. The main page of the Network Control will appear. Set a password. Password needs to be at least eight single byte characters in length and use a mix of the following 3 types of leers: uppercase leers, lowercase leers and digits.

3. Enter the password.

4 5 6

Page 38

4. This page allows you to make adjustments to the AMX and SNMP sengs. In the AMX device discover row, when ON is selected, the projector can be detected by controllers of AMX connected to the same network. For the details of AMX Device Discover, visit the AMX web site at http://www.amx.com/.

5. If your projector is connected to a network which supports Simple Mail Transfer

Protocol (SMTP), you can congure it to alert you via email on signicant events.

6. The Crestron (e-Control)® page displays the Crestron e-Control user interface.

7. Projector Firmware Update

i. Visit ViewSonic’s website to download the Projector Soware Update

Firmware by LAN: https://www.viewsonic.com.

ii. Upload the Projector Firmware le to the Network Control website.

Page 39

iii. Please read the Warning message and press the “OK” buon to conrm the

update.

NOTE: If the download process fails, please refer to the “Projector Soware Update

Firmware by USB” below.

A. Visit ViewSonic’s website to download the Projector Soware Update

Firmware : https://www.viewsonic.com.

B. Connect the USB A cable to the projector and computer. C. Connuously press the projector’s Power Key and Menu Key while

connected to a power outlet.

D. The LED will begin to ash, and downloading will restart.

v. The soware program will start automacally. Please wait for a few minutes

unl it is completed.

vi. Click “Exit” once the update has nished.

CAUTION: Do not turn o the projector or computer while updang.

8. LAN Firmware Update

i. Visit ViewSonic’s website to download the LAN Firmware:

https://www.viewsonic.com.

Page 40

ii. Upload the LAN Firmware le to the Network Control website.

iii. Aer nishing the LAN Firmware update, please go to Crestron e-Control®

page and click the “info” buon to check the LAN Firmware version.

About Crestron e-Control®

1. The Crestron e-Control® page provides a variety of virtual

keys to control the projector or adjust the projected pictures.

ii i

You can press

/ to

reveal more buons.

i. These buons funcon the same as the ones on the OSD menus or remote

control.

ii. To switch between input signals, click on your desired signal.

NOTE:

• The source list varies according to the connecons available on the projector.

Page 41

• When you use the projector control panel or remote control to change the OSD

menu sengs, it may take a while for the web browser to synchronize these changes with the projector.

2. The Tools page allows you to manage the projector, congure the LAN control sengs and secure access to remote network operaons on this projector.

i ii iv

iii

i. This secon is only used with the Crestron Control System. Please contact

Creston or refer to its user manual for setup informaon.

ii. You can name the projector, keep track of its locaon and the person in

charge of it.

iii. You can adjust the LAN Control Settings.

iv. Once set, access to the remote network operaon on this projector will be

password-protected.

v. Once set, access to the tools page will be password-protected.

NOTE:

• To prevent errors, only input the English alphabet and digits on the Tools page.

• Aer making the adjustments, press the “Send” buon and the data will be saved

for the projector.

vi. Press “Exit” to go back to the Remote Network Operaon page.

Page 42

Please pay attention to the limitation of input length (including space and other punctuation keys) in the list blow:

Category Item Input Length Maximum Number of

Characters

IP Address 16

Crestron Control

Projector

Network Conguraon

User Password

Admin Password

IP ID 4 Port 5 Projector Name 22 Locaon 22 Assigned To 22 DHCP (Enabled) (N/A) IP Address 15 Subnet Mask 15 Default Gateway 15 DNS Server 15 Enabled (N/A) New Password 15 Conrm 15 Enabled (N/A) New Password 15 Conrm 15

3. The Info page displays the informaon and status of the projector.

Press “Exit” to go back to the Remote Network Operaon page.

4. Aer selecng the “Contact IT Help”, the HELP DESK window will appear in the upper right corner of the screen. You will be able to deliver messages to RoomView™ soware administrators/users who are connected to the same local area network.

Page 43

For more information, visit http://www.crestron.com &

www.crestron.com/getroomview.

Crestron RoomView

On the “Edit Room” page, enter the IP Address (or hostname) as shown on the projector’s on-screen display (OSD) menu, and “02” for IPID, “41794” for the reserved Crestron control port.

Please go to the below website to get the RoomView™ User Guide and more information:

http://www.crestron.com/products/roomview_connected_embedded_ projectors_devices/resources.asp

PJLink™, SNMP, AMX and Xpanel Formats Supported

This projector is PJLink™, SNMP V.1, AMX or Xpanel V1.10 compliant. For details, please follow its user guide or website respectively to control and manage projectors.

NOTE: PJLink™ can only be used when the password for Network Control has been

set.

Page 44

Menu Functions

This section will introduce the On-Screen Display (OSD) Menu and its options.

General On-Screen Display (OSD) Menu Operation

NOTE: The OSD screenshots in this manual are for reference only and may dier from

the actual design. Some of the following OSD sengs may not be available.

Please refer to the actual OSD of your projector.

The projector is equipped with an On-Screen Display (OSD) Menu for making various adjustments. It can be accessed by pressing Menu on the projector or remote control.

1. Press / to select a main menu. Then press Enter or use / to access the

sub-menu list.

2. Press / to select the menu opon. Then press Enter to display its sub-menu, or press / to adjust/select the seng.

NOTE: Some sub-menu opons may have another sub-menu. To enter the respecve

sub-menu, press Enter. Use / or / to adjust/select the seng.

Page 45

On-Screen Display (OSD) Menu Tree

Main Menu Sub-menu Menu Opon

DISPLAY

Aspect Ratio Auto

4:3 16:9 16:10

Native

Keystone Vertical -40~40

Horizontal

Corner Adj. Top-Right 45°/90°

Top-Left Bottom-Right

Bottom-Left Position X: -5 ~ 5, Y: - 5 ~ 5 Phase 0~31

IMAGE

H. Size -15~15 Zoom 0.8X ~2.0X

OverScan Off/1/2/3/4/5 3X Fast Input Inactive

Active

Color Mode Brightest

Presentation

Standard

Photo

Movie

User 1

User 2

Brightness 0~100 Contrast -50~50

Page 46

Main Menu Sub-menu Menu Opon

IMAGE

Color Temp. 9300K/7500K/6500K

Red Gain 0~100

Green Gain 0~100

Blue Gain 0~100

Red Offset -50~+50

Green Offset -50~+50

Blue Offset -50~+50 Advanced Color -50~50

Tint -50~50

Sharpness 0~31

Gamma 1.8/2.0/2.2/2.35/

2.5/Cubic/sRGB

Noise Reduction 0~31

Color Management Primary Color

Hue Saturation Gain

Reset Color Settings Reset

Cancel Auto Power On Signal Disable/VGA/HDMI/

All CEC Disable/Enable Direct Power On Disable/Enable

Smart Energy Auto Power Off Disable/10 min/20

min/30 min Sleep Timer Disable/30 min/1

hr/2hr/3 hr/4 hr/ 8

hr/12 hr

Power Saving Disable/Enable

Standby Settings Audio Pass Through Off/On

USB A Power On

Off

Page 47

Main Menu Sub-menu Menu Opon

BASIC

Audio Settings Mute Off/On

Audio Volume 0~20 Power On/Off Ring Tone Off/On

Presentation Timer Timer Period 1~240 m

Timer Display Always/1 min/2 min/

3 min/Never

Timer Position

Timer Counting Direction Count Down/Count Up Sound Reminder Off/On Start Counting/Off

Pattern Off

Test Card

Blank Timer

Disable/5 min/10 min/15 min/20 min/25 min/30 min

Top-Left/Bottom-Left/

Top-Right/Bottom-Right

ADVANCED

Message Off

Splash Screen Black

Blue ViewSonic

3D Settings 3D Format Auto

Off

Frame Sequential

Frame Packing

Top-Bottom

Side-by-Side 3D Sync Invert Disable/Invert Save 3D Settings Yes/No

HDMI Settings HDMI Format Auto/RGB/YUV

HDMI Range

Auto/Enhanced/Normal

Page 48

Main Menu Sub-menu Menu Opon

ADVANCED

LAN Control Settings LAN Settings DHCP ON/Static IP

Projector IP Address Subnet Mask

Default Gateway

DNS Server Standby LAN Control Off/On

Apply

Light Source Settings

Light Source Mode Normal/Eco/

Dynamic Black 1/

Dynamic Black 2/

Custom Light Source Power 20%~100% Reset Light Source Hours Reset/Cancel

Light Source Hours Information

Light Source Usage Time

Normal

Eco

Dynamic Black 1

Dynamic Black 2

Custom

Closed Caption Closed Caption Enable Off/On

Caption Version CC1/CC2/CC3/CC4

Reset Settings Reset

Cancel

Page 49

Main Menu Sub-menu Menu Opon

SYSTEM

Language Multi-Language OSD Selection Projector Position Front Table

Rear Table

Rear Ceiling Front Ceiling

Menu Settings Menu Display Time 5 sec/10 sec/15 sec/20

sec/25 sec/30 sec Menu Position Center/Top-Left/

Top-Right/

Bottom-Left/

Bottom-Right

High Altitude Mode Off

Quick Auto Search Off

INFORMATION

Security Settings Change Password

Power On Lock Off/On

Panel Key Lock Off

Remote Control Code Control Method RS-232

Baud Rate 2400/4800/9600/14400/19200/38400/57600/

Source Color Mode Resolution Color System

1/2/3/4/5/6/7/8

USB

115200

IP address

MAC address Firmware Version

3X Fast Input

S/N

Page 50

DISPLAY Menu

1. Press the Menu buon to display the On-Screen Display (OSD) Menu.

2. Press / to select the DISPLAY menu. Then press Enter or use / to access the DISPLAY menu.

3. Press / to select the menu opon. Then press Enter to display its sub-menu,

or press / to adjust/select the seng.

NOTE: Some sub-menu opons may have another sub-menu. To enter the respecve

sub-menu, press Enter. Use / or / to adjust/select the seng.

Page 51

Menu Option Description

Aspect Ratio

Auto

Scales an image proportionally to fit the projector’s native resolution in its horizontal width. This is suitable for the

incoming image which is neither in 4:3 nor 16:9 and you want to make most use of the screen without altering the image’s aspect ratio.

4:3 Scales an image so that it is displayed in the center of the

screen with a 4:3 aspect ratio. This is most suitable for 4:3 images like computer monitors, standard definition TV, and 4:3 aspect DVD movies, as it displays them without aspect

alteration. 16:9

Scales an image so that it is displayed in the center of the

screen with a 16:9 aspect ratio. This is most suitable for images which are already in a 16:9 aspect, like high definition TV, as it

displays them without aspect alteration.

Keystone

Corner Adj.

Position

16:10 Scales an image so that it is displayed in the center of the

screen with a 16:10 aspect ratio. This is most suitable for images which are already in a 16:10 aspect, as it displays them

without aspect alteration.

Native

Projects an image as its original resolution and resizes it to fit within the display area. For input signals with lower

resolutions, the projected image will be displayed in its original

size. Adjusts the keystoning situation where the projected image

becomes a trapezoid due to angled projection. Adjusts the shape and size of an image that is unevenly

rectangular on all sides. Adjust the position of the projected image.

NOTE:

• This funcon is only available when a PC input signal is selected.

Phase

• The adjustment range may vary under dierent mings.

Adjusts the clock phase to reduce image distortion.

NOTE: This funcon is only available when a PC input signal is

selected.

Page 52

Menu Option Description

H. Size

Zoom

OverScan

3X Fast Input

Adjusts the horizontal width of the image.

NOTE: This funcon is only available when a PC input signal is

selected.

Magnifies the projected image and allows you to navigate the

image.

Adjusts the overscan rate from 0% to 5%.

NOTE: This funcon is only available when a Composite Video or

HDMI input signal is selected.

This function is favorable to frame rate reducing. Quick response time in native timing can be achieved. When enabled, the following settings will return to factory preset values: Aspect Ratio, Position, Zoom, OverScan.

NOTE: This funcon is only available when a nave ming input

signal is selected.

Page 53

IMAGE Menu

1. Press the Menu buon to display the On-Screen Display (OSD) Menu.

2. Press / to select the IMAGE menu. Then press Enter or use / to access the IMAGE menu.

3. Press / to select the menu opon. Then press Enter to display its sub-menu,

or press / to adjust/select the seng.

NOTE: Some sub-menu opons may have another sub-menu. To enter the respecve

sub-menu, press Enter. Use / or / to adjust/select the seng.

Page 54

Menu Option Description

Color Mode

Brightest

Maximizes the brightness of the projected image. This mode is suitable for environments where extra-high brightness is required, such as using the projector in well lit rooms.

Presentation

Designed for presentations under daylight environment to match PC and notebook coloring.

Standard

Designed for normal circumstances in a daylight environment.

Photo

Designed for photo viewing. Movie

For playing colorful movies, video clips from digital cameras or DVs through the PC input for best viewing in a blackened (little light) environment.

User 1/User 2

Recalls the customized settings. After User 1/User 2 is selected, some of the sub-menus under the IMAGE menu can be adjusted, according to your selected input source.

Brightness

Contrast

The higher the value, the brighter the image.

Adjust this option so the

black areas of the image appear just as black and

details in the dark area are

more visible. Use this to set the peak white level after you have

previously adjusted the

Brightness setting.

Page 55

Menu Option Description

Color Temp.

Advanced

9300K

Images appear bluish white.

7500K

Images maintain a normal white appearance.

6500K

Images appear reddish white.

To set a custom color temperature, you can further adjust the

following items: Red Gain/Green Gain/Blue Gain

Adjusts the Contrast levels of Red, Green, and Blue.

Red Offset/Green Offset/Blue Offset

Adjusts the Brightness levels of Red, Green, and Blue.

Color

A lower setting produces less saturated colors. If the setting is too high, colors will be overpowering and may appear

unrealistic.

Advanced

Tint

A higher value will make the picture more greenish while a lower value will make the picture more reddish.

Sharpness

A higher value will sharpen the image, while a lower value will

soften the image. Gamma

Gamma refers to the brightness level of the projector’s grayscale levels.

Noise Reduction

This function reduces electrical image noise caused by different media players. The higher the setting, the less the noise. (Not available when input signal is HDMI.)

Color Management

Only in permanent installations with controlled lighting levels such as boardrooms, lecture theaters, or home theaters, should color management be considered. Color management provides fine color control adjustment to allow for more

accurate color reproduction. Select Primary Color first and

adjust its range/values in Hue, Saturation and Gain.

Reset Color Settings

Returns current image settings to the factory preset values.

Page 56

POWER MANAGEMENT Menu

1. Press the Menu buon to display the On-Screen Display (OSD) Menu.

2. Press / to select the POWER MANAGEMENT menu. Then press Enter or use

/ to access the POWER MANAGEMENT menu.

3. Press / to select the menu opon. Then press Enter to display its sub-menu,

or press / to adjust/select the seng.

NOTE: Some sub-menu opons may have another sub-menu. To enter the respecve

sub-menu, press Enter. Use / or / to adjust/select the seng.

Page 57

Menu Option Description

Auto Power On

Signal

Selecting VGA/HDMI allows the projector to turn on automatically once the VGA/HDMI signal is fed through the VGA/HDMI cable. You can also select All and the projector will turn on automatically upon receiving either a VGA or HDMI

signal. CEC

This projector supports CEC (Consumer Electronics Control)

function for synchronized power on/off operation via HDMI connection. That is, if a device that also supports CEC function is connected to the HDMI input of the projector, when the projector’s power is turned off, the power of the connected device will also be turned off automatically. When the power of the connected device is turned on, the projector’s power will be turned on automatically.

NOTE:

• In order for the CEC funcon to work properly, make sure

that the device is correctly connected to the HDMI input of the projector via an HDMI cable, and its CEC funcon is

turned on.

Smart Energy

• Depending on the connected device, the CEC funcon may not work.

Direct Power On Allows the projector to turn on automatically once power is fed through the power cord.

Auto Power Off Allows the projector to turn off automatically after a set

period of time once no input source is detected to prevent

unnecessary waste of light source life. Sleep Timer

Allows the projector to turn off automatically after a set period

of time to prevent unnecessary waste of light source life. Power Saving

Lowers power consumption if no input source is detected.

When Enable is selected, the projector will change to Power Saving mode after no signal is detected for five (5) minutes. This will also help prevent any unnecessary waste of

light source life.

Page 58

Menu Option Description

Standby Settings

USB A Power

The functions below are available in standby mode (plugged in, but not turned on).

Audio Pass Through

When selecting On, the projector outputs an audio signal when the Audio In and Audio Out sockets are correctly connected to a proper device.

When On, the USB Type A port can supply power, and the

Control Method will automatically switch to RS-232.

Page 59

BASIC Menu

1. Press the Menu buon to display the On-Screen Display (OSD) Menu.

2. Press / to select the BASIC menu. Then press Enter or use / to access the BASIC menu.

3. Press / to select the menu opon. Then press Enter to display its sub-menu,

or press / to adjust/select the seng.

NOTE: Some sub-menu opons may have another sub-menu. To enter the respecve

sub-menu, press Enter. Use / or / to adjust/select the seng.

Page 60

Menu Option Description

Audio Settings

Presentation Timer

Mute Select On to temporarily turn off the projector’s internal

speaker or the volume being output from the audio output

jack. Audio Volume

Adjusts the volume level of the projector’s internal speaker or the volume being output from the audio output jack.

Power On/Off Ring Tone Turns on/off the ring tone during the starting up and shutting down process.

Presentation timer can indicate the presentation time on the

screen to help you achieve better time management when giving presentations.

Timer Period

Sets the time period. If the timer is already on, the timer will restart whenever the Timer Period is reset.

Timer Display Allows you to decide if you want the timer to show up on the screen for one of the following time periods:

 Always: Displays the mer on screen throughout the

presentaon me.

 1 min/2 min/3 min: Displays the mer on screen in the

last 1/2/3 minute(s).

 Never: Hides the mer throughout the presentaon me.

Timer Position Sets the timer position.

Timer Counting Direction

Sets your desired counting direction between:

 Count Down: Decreases from the preset me to 0.  Count Up: Increases from 0 to the preset me.

Sound Reminder

Allows you to decide if you want to activate a sound reminder. Once enabled, a double beep sound will be heard at the last 30 seconds of counting down/up, and a triple beep sound will be

produced when the timer is up. Start Counting/Off

Select Start Counting to activate the timer. Select Off to cancel

it.

Page 61

Menu Option Description

Pattern

Blank Timer

Message Splash Screen

Helps adjust the image size and focus, and checks for distortion

in the projected image. Allows the projector to return the image automatically after a

period of time when there is no action taken on the blank

screen. To display the blank screen, press Blank on the projector

or remote control.

NOTE: Do not block the projecon lens as this could cause the

blocking object to become heated and deformed or even cause a re.

Sets reminder messages, i.e. “Blank” message, On or Off.

Selects which logo screen will appear during projector start-up.

Page 62

ADVANCED Menu

1. Press the Menu buon to display the On-Screen Display (OSD) Menu.

2. Press / to select the ADVANCED menu. Then press Enter or use / to access the ADVANCED menu.

3. Press / to select the menu opon. Then press Enter to display its sub-menu,

or press / to adjust/select the seng.

NOTE: Some sub-menu opons may have another sub-menu. To enter the respecve

sub-menu, press Enter. Use / or / to adjust/select the seng.

Page 63

Menu Option Description

3D Settings

This projector features a 3D function which enables you to enjoy 3D movies, videos, and sporting events in a more realistic way by presenting the depth of the images. You need to wear a pair of 3D glasses to view 3D images.

3D Format The default setting is Auto and the projector automatically chooses an appropriate 3D format when detecting 3D

contents. If the projector cannot recognize the 3D format,

choose a 3D mode.

3D Sync Invert When you discover the inversion of the image depth, enable this function to correct the problem.

Save 3D Settings Saves current 3D settings. 3D settings will automatically be

applied if the same resolution and input source are selected.

NOTE: When the 3D Sync funcon is on:

• The brightness level of the projected image will decrease.

HDMI Settings

• The Color Mode, Light Source Mode, Zoom, and OverScan

cannot be adjusted.

HDMI Format Select a suitable color space according to the color space setting of the output device connected.

 Auto: Sets the projector to detect the color space seng

of the input signal automacally.

 RGB: Sets the color space as RGB.  YUV: Sets the color space as YUV.

HDMI Range Select a suitable HDMI color range according to the color range setting of the output device connected.

 Auto: Sets the projector to detect the HDMI range of the

input signal automacally.

 Enhanced: Sets the HDMI color range as 0 - 255.  Normal: Sets the HDMI color range as 16 - 235.

Page 64

Menu Option Description

LAN Control Settings

LAN Settings

 DHCP ON: Select this if you are in a DHCP environment

and Projector IP Address, Subnet Mask, Default Gateway,

DNS Server settings will be automatically retrieved.

 Static IP: Select this if you are in a non-DHCP environment

and make adjustments to below settings.

Projector IP Address Subnet Mask

Default Gateway

DNS Server

Standby LAN Control Allows the projector to provide the network function in

standby mode.

Apply Enacts the settings.

Only available when LAN Settings is set to Static IP. Use / to select a

column and use / to adjust the

value.

Light Source Settings

Light Source Mode

 Normal: Provides full light source brightness.  Eco: Reduces light source power consumpon by 30% and

lowers brightness to decrease the fan noise.

 Dynamic Black 1: Reduces light source power

consumpon by up to 95% depending on the content brightness level.

 Dynamic Black 2: Reduces light source power

consumpon by up to 60% depending on the content brightness level.

 Custom: Allows you to adjust the light source power.

Light Source Power

Only available when Light Source Mode is Custom.

Reset Light Source Hours Resets the light source timer after new light source is installed.

For changing the light source, please contact qualified service

personnel.

Light Source Hours Information

 Light Source Usage Time: Displays the number of hours

the light source has been used.

Page 65

Menu Option Description

Closed Caption

Reset Settings

Closed Caption Enable Activates the function when the selected input signal carries

closed captions.

NOTE:

• Capons: An on-screen display of the dialogue, narraon,

and sound eects of TV programs and videos that are closed caponed (usually marked as “CC” in TV lisngs).

• This funcon is only available when a Composite video input signal is selected and its system format is NTSC.

Caption Version

To view captions, select CC1, CC2, CC3, or CC4 (CC1 displays

captions in the primary language in your area).

Returns all settings to the factory preset values. When using Reset Settings, the following settings will still remain: Language, Projector Position, High Altitude Mode, Security Settings, Remote Control Code, Zoom, Keystone, Control Method, USB A Power, Corner Adj. and Baud Rate.

Page 66

SYSTEM Menu

1. Press the Menu buon to display the On-Screen Display (OSD) Menu.

2. Press / to select the SYSTEM menu. Then press Enter or use / to access the SYSTEM menu.

3. Press / to select the menu opon. Then press Enter to display its sub-menu,

or press / to adjust/select the seng.

NOTE: Some sub-menu opons may have another sub-menu. To enter the respecve

sub-menu, press Enter. Use / or / to adjust/select the seng.

Page 67

Menu Option Description

Language Projector Position Menu Settings

High Altitude Mode

Sets the language for the On-Screen Display (OSD) Menu. Selects a proper position for the projector. Menu Display Time

Sets the length of time the OSD Menu will remain active after

your last interaction. Menu Position

Sets the OSD Menu’s position.

We recommend you use the High Altitude Mode when your environment is between 1,501 m to 3,000 m above sea level, and ambient temperature is between 0°C–30°C.

NOTE:

• Do not use High Altude Mode if your environment is

between 0 to 1,500 m, and the temperature is between 0°C to 35°C. If used, the projector will become over

cooled.

• Using “High Altude Mode” may cause more operang

noise, as the fan speed will be increased to improve

cooling and performance.

Quick Auto Search Security Settings Panel Key Lock Remote Control Code

Allows the projector to automatically search for the signals. See “Using the Password Function” on page 20. Locks the control keys on the projector.

Sets the remote control code for this projector (between 1~8). When multiple adjacent projectors are in operaon at the same

me, switching the codes can prevent interference from other remote controls. Aer the remote control code is set, switch to the same ID for the remote control to control this projector. To switch the code for the remote control, press ID set and the number buon corresponding to the remote control code together for 5 seconds or more. The inial code is set to 1. When the code is switched to 8, the remote control can control every projector.

NOTE: If dierent codes are set on the projector and remote

control, there will be no response from the remote control. When that happens, a message will display to

remind you to switch the code for the remote control.

Control Method

Allows you to select a preferred control port: through the

RS-232 port, the USB port or the HDBaseT port. When selecting USB, USB A Power will be switched to Off automatically.

Page 68

Menu Option Description

Baud Rate

Selects a baud rate that is identical with your computer’s so

that you can connect the projector using a suitable RS-232 cable and control the projector with RS-232 commands

Page 69

INFORMATION Menu

1. Press the Menu buon to display the On-Screen Display (OSD) Menu.

2. Press / to select the INFORMATION menu and display its contents.

Menu Option Description

Source Color Mode Resolution

Color System

IP address

MAC address Firmware Version

3X Fast Input

S/N

Shows the current input source.

Shows the selected mode in the IMAGE menu. Shows the native resolution of the input source.

Shows input system format.

Shows the IP address of your projector.

Shows the MAC Address of your projector.

Shows the current firmware version. Shows whether the function is activated or not. Shows the serial number for this projector.

Page 70

Appendix

Specifications

Item Category LS600W

Projector Type LED

Display Size 60” ~ 300”

Throw Ratio 1.37~1.64 (87”±3%@2.56m)

Lens 1.2x±3% Optical Zoom

Light Source

OSRAM LED (RGBB/P2MQ)

Type

Display

1-CHIP DMD

System

Input Signal VGA fh: 15K~102KHz, fv:48~120Hz, Pixel rate: 170MHz

HDMI fh: 15K~102KHz, fv:23~120Hz, Pixel rate: 170MHz

Resolution Native 1280 x 800 Power Adapter1Input Voltage AC 100-240V, 50/60 Hz (auto switch) Operating

conditions

Temperature 0°C to 40°C (32°F to 104°F)

Humidity 10% to 90% (non-condensing)

Altitude 0 to 1,500 m at 0°C to 35°C

1,501 to 3,000 m at 0°C to 30°C

Storage conditions

Temperature -20°C to 60°C (non-condensing)

Humidity 10% to 90% (non-condensing)

Altitude 0 to 40,000 ft sea level at -20°C to 30°C

Dimensions Physical

(W x D x H)

386 mm x 276 mm x 116 mm

(15.2” x 10.9” x 4.6” ) Weight Physical 5±0.2 kg (11 lbs) Power Saving

Modes

Please use the power adapter from ViewSonic® or an authorized source only.

The test condition follows EEI standards.

400W (Typical)

Off < 0.5W (Standby)

Page 71

Projector Dimensions

386 mm (W) x 276 mm (D) x 116 mm (H)

386 mm

276 mm

BLANK

EXIT

ENTER

SOURCE

COLOR MODE

76 mm

61 mm

Timing Chart

Analog RGB

Resolution Mode Refresh

rate (Hz)

720 x 400 720 x 400_70 70.087 31.469 28.3221

640 x 480 VGA_60 59.94 31.469 25.175 Supported Supported Supported

VGA_72 72.809 37.861 31.5

VGA_75 75 37.5 31.5

VGA_85 85.008 43.269 36

H-

frequency

(kHz)

Clock

(MHz)

3D Sync

Frame Sequential Top-Bottom Side-by-Side

116 mm

800 x 600 SVGA_60 60.317 37.879 40 Supported Supported Supported

SVGA_72 72.188 48.077 50

SVGA_75 75 46.875 49.5

SVGA_85 85.061 53.674 56.25

SVGA_120 (Reduce

119.854 77.425 83 Supported

Blanking)

1024 x 768 XGA_60 60.004 48.363 65 Supported Supported Supported

XGA_70 70.069 56.476 75

XGA_75 75.029 60.023 78.75

XGA_85 84.997 68.667 94.5

XGA_120 (Reduce

119.989 97.551 115.5 Supported

Blanking)

1152 x 864 1152 x 864_75 75 67.5 108

1024 x 576 NB Timing 60 35.82 46.966

1024 x 600 NB Timing 64.995 41.467 51.419

1280 x 720 1280 x 720_60 60 45 74.25 Supported Supported Supported

1280 x 768 1280 x 768_60 59.87 47.776 79.5 Supported Supported Supported

Page 72

Resolution Mode Refresh

rate (Hz)

1280 x 800 WXGA_60 59.81 49.702 83.5 Supported Supported Supported

WXGA_75 74.934 62.795 106.5

WXGA_85 84.88 71.554 122.5

H-

frequency

(kHz)

Clock

(MHz)

3D Sync

Frame Sequential Top-Bottom Side-by-Side

WXGA_120 (Reduce

Blanking)

1280 x 1024 SXGA_60 60.02 63.981 108 Supported Supported Supported

SXGA_75 75.025 79.976 135

SXGA_85 85.024 91.146 157.5

1280 x 960 1280 x 960_60 60 60 108 Supported Supported Supported

1280 x 960_85 85.002 85.938 148.5

1360 x 768 1360 x 768_60 60.015 47.712 85.5 Supported Supported Supported

1440 x 900 WXGA+_60 59.887 55.935 106.5 Supported Supported Supported

1400 x 1050 SXGA+_60 59.978 65.317 121.75 Supported Supported Supported

1600 x 1200 UXGA 60 75 162 Supported Supported Supported

1680 x 1050 1680x1050_60 59.954 65.29 146.25 Supported Supported Supported

640 x 480@67Hz MAC13 66.667 35 30.24

832 x 624@75Hz MAC16 74.546 49.722 57.28

1024 x 768@75Hz MAC19 74.93 60.241 80

1152 x 870@75Hz MAC21 75.06 68.68 100

119.909 101.563 146.25 Supported

1920 x 1080 (VESA) 1920 x 1080_60 60 67.5 148.5 Supported Supported Supported

Page 73

HDMI (PC)

Resolution Mode Refresh

rate (Hz)

640 x 480 VGA_60 59.94 31.469 25.175 Supported Supported Supported

VGA_72 72.809 37.861 31.5

VGA_75 75 37.5 31.5

VGA_85 85.008 43.269 36

720 x 400 720 x 400_70 70.087 31.469 28.3221

800 x 600 SVGA_60 60.317 37.879 40 Supported Supported Supported

SVGA_72 72.188 48.077 50

SVGA_75 75 46.875 49.5

SVGA_85 85.061 53.674 56.25

SVGA_120 (Reduce

Blanking)

1024 x 768 XGA_60 60.004 48.363 65 Supported Supported Supported

XGA_70 70.069 56.476 75

XGA_75 75.029 60.023 78.75

119.854 77.425 83 Supported

H-

frequency

(kHz)

Clock

(MHz)

3D Sync

Frame Sequential Top-Bottom Side-by-Side

XGA_85 84.997 68.667 94.5

XGA_120 (Reduce

Blanking)

1152 x 864 1152 x 864_75 75 67.5 108

1024 x 576 NB Timing 60 35.82 46.966

1024 x 600 NB Timing 64.995 41.467 51.419

1280 x 720 1280 x 720_60 60 45 74.25 Supported Supported Supported

1280 x 768 1280 x 768_60 59.87 47.776 79.5 Supported Supported Supported

1280 x 800 WXGA_60 59.81 49.702 83.5 Supported Supported Supported

WXGA_75 74.934 62.795 106.5

WXGA_85 84.88 71.554 122.5

WXGA_120 (Reduce

Blanking)

1280 x 1024 SXGA_60 60.02 63.981 108 Supported Supported Supported

SXGA_75 75.025 79.976 135

SXGA_85 85.024 91.146 157.5

1280 x 960 1280 x 960_60 60 60 108 Supported Supported Supported

119.989 97.551 115.5 Supported

119.909 101.563 146.25 Supported

1280 x 960_85 85.002 85.938 148.5

1360 x 768 1360 x 768_60 60.015 47.712 85.5 Supported Supported Supported

1440 x 900 WXGA+_60 59.887 55.935 106.5 Supported Supported Supported

1400 x 1050 SXGA+_60 59.978 65.317 121.75 Supported Supported Supported

1600 x 1200 UXGA 60 75 162 Supported Supported Supported

Page 74

Resolution Mode Refresh

rate (Hz)

1680 x 1050 1680 x 1050_60 59.954 65.29 146.25 Supported Supported Supported

640 x 480@67Hz MAC13 66.667 35 30.24

832 x 624@75Hz MAC16 74.546 49.722 57.28

1024 x 768@75Hz MAC19 74.93 60.241 80

1152 x 870@75Hz MAC21 75.06 68.68 100

1920 x 1080 (VESA) 1920 x 1080_60 60 67.5 148.5 Supported Supported Supported

H-

frequency

(kHz)

Clock

(MHz)

3D Sync

Frame Sequential Top-Bottom Side-by-Side

HDMI (Video)

Video mode

480i 720(1440) x 480 15.73 59.94 27 Supported

480p 720 x 480 31.47 59.94 27 Supported Supported Supported

576i 720(1440) x 576 15.63 50 27 Supported

576p 720 x 576 31.25 50 27 Supported Supported Supported

720/50p 1280 x 720 37.5 50 74.25 Supported Supported Supported Supported

720/60p 1280 x 720 45 60 74.25 Supported Supported Supported Supported

1080/50i 1920 x 1080 28.13 50 74.25 Supported Supported Supported

1080/60i 1920 x 1080 33.75 60 74.25 Supported Supported Supported

1080/24P 1920 x 1080 27 24 74.25 Supported

1080/50P 1920 x 1080 56.25 50 148.5 Supported Supported Supported

1080/60P 1920 x 1080 67.5 60 148.5 Supported Supported Supported

Resolution Horizontal

frequency

(KHz)

Vertical

frequency

(Hz)

Dot Clock

frequency

(MHz)

3D Sync

Frame Sequential Frame Packing Top-Bottom Side-by-Side

Video/S-Video

Video mode Horizontal frequency

(KHz)

Vertical frequency

(Hz)

Sub-carrier Frequency

(MHz)

NTSC 15.73 60 3.58

PAL 15.63 50 4.43

SECAM 15.63 50 4.25 or 4.41

PAL-M 15.73 60 3.58

PAL-N 15.63 50 3.58

PAL-60 15.73 60 4.43

NTSC4.43 15.73 60 4.43

Page 75

Component video

Video mode Resolution Horizontal

frequency

(KHz)

480i 720 x 480 15.73 59.94 13.5 Supported

480p 720 x 480 31.47 59.94 27 Supported

576i 720 x 576 15.63 50 13.5 Supported

576p 720 x 576 31.25 50 27 Supported

720/50p 1280 x 720 37.5 50 74.25

720/60p 1280 x 720 45 60 74.25

1080/50i 1920 x 1080 28.13 50 74.25

1080/60i 1920 x 1080 33.75 60 74.25

1080/50P 1920 x 1080 56.25 50 148.5

1080/60P 1920 x 1080 67.5 60 148.5

Vertical frequency

(Hz)

Clock (MHz) 3D Sync

Frame Sequential

Page 76

IR Control Table

Key Format Byte 1 Byte 2 Byte 3 Byte 4

Off

COMP NEC-F2 83 F4 41 BE

HDMI/HDMI 1 NEC-F2 83 F4 58 A7

HDMI 2 NEC-F2 83 F4 59 A6

Auto Sync NEC-F2 83 F4 8 F7

Source NEC-F2 83 F4 40 BF

Up/

Left/

Enter/

Right/

Down/

Menu NEC-F2 83 F4 30 CF

NEC-F2 83 F4 4F B0

NEC-F2 83 F4 4E B1

NEC-F2 83 F4 0B F4 NEC-F2 83 F4 0E F1 NEC-F2 83 F4 15 EA

NEC-F2 83 F4 0F F0

NEC-F2 83 F4 0C F3

NEC-F2 83 F4 97 68

(INFORMATION)

Exit NEC-F2 83 F4 28 D7 Aspect NEC-F2 83 F4 13 EC Freeze NEC-F2 83 F4 03 FC

Pattern NEC-F2 83 F4 55 AA

Blank NEC-F2 83 F4 7 F8

PgUp NEC-F2 83 F4 06 F9 PgDn NEC-F2 83 F4 05 FA

(Mute)

(Volume Down)

(Volume Up)

(Zoom in)

(Zoom out)

NEC-F2 83 F4 14 EB

NEC-F2 83 F4 83 7C

NEC-F2 83 F4 82 7D

NEC-F2 83 F4 67 98

NEC-F2 83 F4 68 97

Eco Mode NEC-F2 83 F4 2B D4

Color Mode NEC-F2 83 F4 10 EF

Network NEC X3 F4 69 96

Page 77

Key Format Byte 1 Byte 2 Byte 3 Byte 4

(Presentation

Timer)

VIDEO NEC 83 F4 52 AD

Address Code

NEC X3 F4 27 D8

Code 1 83F4 Code 2 93F4 Code 3 A3F4 Code 4 B3F4 Code 5 C3F4 Code 6 D3F4 Code 7 E3F4 Code 8 F3F4

Page 78

RS-232 Command Table

Pin Assignment

Pin Description Pin Description

1 3 5 7 9

GND

RTSZ

2 4 6 8

RX NC NC

CTSZ

Interface

RS-232 Protocol

Baud Rate Data Length Parity Check Stop Bit Flow Control

115200 bps (default)

8 bit

None

1 bit

None

Command Table

Function Type Action Command

Power Write ON 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x00 0x00 0x5D Power Write OFF 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x01 0x00 0x5E

Power Write ON/OFF 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x34 0x00 0x91 Power Read Status 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x11 0x00 0x5E Reset Settings Write Reset Settings 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x02 0x00 0x5F Reset Color

Settings Reset to Factory

Default Splash Screen Write Black 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x0A 0x00 0x67 Splash Screen Write Blue 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x0A 0x01 0x68 Splash Screen Write ViewSonic 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x0A 0x02 0x69 Splash Screen Read Status 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x11 0x0A 0x68 Quick Power Off Write OFF 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x0B 0x00 0x68 Quick Power Off Write ON 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x0B 0x01 0x69 Quick Power Off Read Status 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x11 0x0B

Write Reset Color

Settings

Write Reset to

Factory Default

0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x2A 0x00 0x87

0x06 0x14 0x00 0x03 0x00 0x34 0x0C 0x08 0x5F

0x69 High Altitude Mode Write OFF 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x0C 0x00 0x69 High Altitude Mode Write ON 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x0C 0x01 0x6A High Altitude Mode Read Status 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x11 0x0C 0x6A

Page 79

Function Type Action Command

Light Source Mode Write Normal 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x10 0x00 0x6D Light Source Mode Write Eco 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x10 0x01 0x6E Light Source Mode Write Dynamic Eco 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x10 0x02 0x6F Light Source Mode Write Custom 20 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x10 0x04 0x71 Light Source Mode Write Custom 40 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x10 0x05 0x72 Light Source Mode Write Custom 60 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x10 0x06 0x73 Light Source Mode Write Custom 80 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x10 0x07 0x74 Light Source Mode Write Custom 100 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x10 0x08 0x75 Light source mode Write Dynamic Black 1 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x10 0x09 0x76 Light source mode Write Dynamic Black 2 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x10 0x0A 0x77 Light Source Mode Read Status 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x11 0x10 0x6E Message Write OFF 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x27 0x00 0x84 Message Write ON 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x27 0x01 0x85 Message Read Status 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x11 0x27 0x85 Projector Position Write Front Table 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x00 0x00 0x5E Projector Position Write Rear Table 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x00 0x01 0x5F Projector Position Write Rear Ceiling 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x00 0x02 0x60 Projector Position Write Front Ceiling 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x00 0x03 0x61 Projector Position Read Status 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x12 0x00 0x5F 3D Sync Write OFF 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x20 0x00 0x7E 3D Sync Write Auto 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x20 0x01 0x7F 3D Sync Write Frame

Sequential 3D Sync Write Frame Packing 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x20 0x03 0x81 3D Sync Write Top Bottom 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x20 0x04 0x82 3D Sync Write Side by Side 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x20 0x05 0x83 3D Sync Read Status 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x12 0x20 0x7F 3D Sync Invert Write OFF 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x21 0x00 0x7F 3D Sync Invert Write ON 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x21 0x01 0x80 3D Sync Invert Read Status 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x12 0x21 0x80 Contrast Write Decrease 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x02 0x00 0x60 Contrast Write Increase 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x02 0x01 0x61

0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x20 0x02 0x80

Contrast Read Get Value 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x12 0x02 0x61 Brightness Write Decrease 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x03 0x00 0x61 Brightness Write Increase 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x03 0x01 0x62 Brightness Read Get Value 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x12 0x03 0x62 Aspect ratio Write Auto 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x04 0x00 0x62 Aspect ratio Write 4:3 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x04 0x02 0x64 Aspect ratio Write 16:9 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x04 0x03 0x65

Page 80

Function Type Action Command

Aspect ratio Write 16:10 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x04 0x04 0x66 Aspect ratio Write Anamorphic 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x04 0x05 0x67 Aspect ratio Write Wide 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x04 0x06 0x68 Aspect ratio Write 2.35:1 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x04 0x07 0x69 Aspect ratio Write Panorama 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x04 0x08 0x6A Aspect ratio Write Native 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x04 0x09 0x6B Aspect ratio Write Cycle 0x06 0x14 0x00 0x04 0x00 0x34 0x13 0x31 0x00 0x90 Aspect ratio Read Get Value 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x12 0x04 0x63 Auto Adjust Write Execute 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x05 0x00 0x63 Horizontal position Write Shift Right 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x06 0x01 0x65 Horizontal position Write Shift Left 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x06 0x00 0x64 Horizontal position Read Get Value 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x12 0x06 0x65 Vertical position Write Shift Up 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x07 0x00 0x65 Vertical position Write Shift Down 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x07 0x01 0x66 Vertical position Read Get Value 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x12 0x07 0x66 Color temperature Write Warm/5500K 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x08 0x00 0x66 Color temperature Write Normal/6500K 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x08 0x01 0x67 Color temperature Write Neutral/7500K 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x08 0x02 0x68 Color temperature Write Cool/8000K/

8500K Color temperature Write 9300K 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x08 0x04 0x6A Color temperature Write 9000K 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x08 0x05 0x6B Color temperature Write User 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x0B 0x06 0x6C Color temperature Read Get Value 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x12 0x08 0x67 Color temperature-

Red gain Color temperature-

Green gain

Write Decrease 0x06 0x14 0x00 0x05 0x00 0x34 0x12 0x3A 0x00 0x00 0x99

Write Increase 0x06 0x14 0x00 0x05 0x00 0x34 0x12 0x3A 0x00 0x01 0x9A

Read Get value 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x12 0x3B 0x9A

Write Decrease 0x06 0x14 0x00 0x05 0x00 0x34 0x12 0x3A 0x01 0x00 0x9A

0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x08 0x03 0x69

Color temperatureGreen gain

Color temperatureBlue gain

Write Increase 0x06 0x14 0x00 0x05 0x00 0x34 0x12 0x3A 0x01 0x01 0x9B

Read Get value 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x12 0x3C 0x9B

Write Decrease 0x06 0x14 0x00 0x05 0x00 0x34 0x12 0x3A 0x02 0x00 0x9B

Write Increase 0x06 0x14 0x00 0x05 0x00 0x34 0x12 0x3A 0x02 0x01 0x9C

Page 81

Function Type Action Command

Color temperatureBlue gain

Color temperatureRed offset

Color temperatureGreen offset

Color temperatureGreen gain

Color temperatureGreen offset

Color temperatureBlue offset

Read Get value 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x12 0x3D 0x9C

Write Decrease 0x06 0x14 0x00 0x05 0x00 0x34 0x12 0x3E 0x00 0x00 0x9D

Write Increase 0x06 0x14 0x00 0x05 0x00 0x34 0x12 0x3E 0x00 0x01 0x9E

Read Get value 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x12 0x3F 0x9E

Write Decrease 0x06 0x14 0x00 0x05 0x00 0x34 0x12 0x3E 0x01 0x00 0x9E

Write Increase 0x06 0x14 0x00 0x05 0x00 0x34 0x12 0x3E 0x01 0x01 0x9F

Read Get value 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x12 0x40 0x9F

Write Decrease 0x06 0x14 0x00 0x05 0x00 0x34 0x12 0x3E 0x02 0x00 0x9F

Write Increase 0x06 0x14 0x00 0x05 0x00 0x34 0x12 0x3E 0x02 0x01 0xA0

Color temperatureBlue offset

Blank Write ON 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x09 0x01 0x68 Blank Write OFF 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x09 0x00 0x67 Blank Read Status 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x12 0x09 0x68 Keystone-Vertical Write Decrease 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x0A 0x00 0x68 Keystone-Vertical Write Increase 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x0A 0x01 0x69 Keystone-Vertical Read Get value 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x12 0x0A 0x69 Keystone-

Horizontal Keystone-

Horizontal Color mode Write Brightest 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x0B 0x00 0x69 Color mode Write Movie 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x0B 0x01 0x6A Color mode Write Standard 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x0B 0x04 0x6D

Read Get value 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x12 0x41 0xA0

Write Decrease 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x31 0x00 0x8E

Write Increase 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x31 0x01 0x8F

Read Get value 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x11 0x31 0x8F

Color mode Write sRGB/

ViewMatch Color mode Write Dynamic 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x0B 0x08 0x71 Color mode Write Rec709 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x0B 0x09 0x72 Color mode Write DICOM SIM 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x0B 0x0a 0x73 Color mode Write Sports 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x0B 0x11 0x7A

0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x0B 0x05 0x6E

Page 82

Function Type Action Command

Color mode Write Photo 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x0B 0x13 0x7C Color mode Write Presentation 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x0B 0x14 0x7D Color mode Write Gaming 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x0B 0x12 0x7B Color mode Write Vivid 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x0B 0x15 0x7E Color mode Write ISF Day 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x0B 0x16 0x7F Color mode Write ISF Night 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x0B 0x17 0x80 Color mode Write Cycle 0x06 0x14 0x00 0x04 0x00 0x34 0x13 0x33 0x00 0x92 Color mode Write User1 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x0B 0x18 0x81 Color mode Write User2 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x0B 0x19 0x82 Color mode Write TV 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x0B 0x1A 0x83 Color mode Read Status 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x12 0x0B 0x6A Reset current color

settings Primary Color Write R 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x10 0x00 0x6E Primary Color Write G 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x10 0x01 0x6F Primary Color Write B 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x10 0x02 0x70 Primary Color Write C 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x10 0x03 0x71 Primary Color Write M 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x10 0x04 0x72 Primary Color Write Y 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x10 0x05 0x73 Primary Color Read Status 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x12 0x10 0x6F Hue / Tint Write Decrease 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x11 0x00 0x6F Hue / Tint Write Increase 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x11 0x01 0x70 Hue / Tint Read Get value 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x12 0x11 0x70 Saturation Write Decrease 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x12 0x00 0x70 Saturation Write Increase 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x12 0x01 0x71 Saturation Read Get value 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x12 0x12 0x71 Gain Write Decrease 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x13 0x00 0x71 Gain Write Increase 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x13 0x01 0x72

Write Reset 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x2A 0x00 0x87

Gain Read Get value 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x12 0x13 0x72 Sharpness Write Decrease 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x0E 0x00 0x6C Sharpness Write Increase 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x0E 0x01 0x6D Sharpness Read Get value 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x12 0x0E 0x6D Freeze Write ON 0x06 0x14 0x00 0x04 0x00 0x34 0x13 0x00 0x01 0x60 Freeze Write OFF 0x06 0x14 0x00 0x04 0x00 0x34 0x13 0x00 0x00 0x5F Freeze Read Status 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x13 0x00 0x60 Source input Write D-Sub/Comp. 1 0x06 0x14 0x00 0x04 0x00 0x34 0x13 0x01 0x00 0x60 Source input Write HDMI 1 0x06 0x14 0x00 0x04 0x00 0x34 0x13 0x01 0x03 0x63 Source input Write HDMI 2 0x06 0x14 0x00 0x04 0x00 0x34 0x13 0x01 0x07 0x67

Page 83

Function Type Action Command

Source input Write Composite

Video Source input Read Status 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x13 0x01 0x61 Quick Auto Search Write ON 0x06 0x14 0x00 0x04 0x00 0x34 0x13 0x02 0x01 0x62 Quick Auto Search Write OFF 0x06 0x14 0x00 0x04 0x00 0x34 0x13 0x02 0x00 0x61 Quick Auto Search Read Status 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x13 0x02 0x62 Mute Write ON 0x06 0x14 0x00 0x04 0x00 0x34 0x14 0x00 0x01 0x61 Mute Write OFF 0x06 0x14 0x00 0x04 0x00 0x34 0x14 0x00 0x00 0x60 Mute Read Status 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x14 0x00 0x61 Volume Write Increase 0x06 0x14 0x00 0x04 0x00 0x34 0x14 0x01 0x00 0x61 Volume Write Decrease 0x06 0x14 0x00 0x04 0x00 0x34 0x14 0x02 0x00 0x62 Volume Write Write Value 0x06 0x14 0x00 0x04 0x00 0x34 0x13 0x2A 0x11 0x9A Volume Read Get Value 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x14 0x03 0x64 Language Write English 0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x00 0x61 Language Write Français 0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x01 0x62 Language Write Deutsch 0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x02 0x63 Language Write Italiano 0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x03 0x64

0x06 0x14 0x00 0x04 0x00 0x34 0x13 0x01 0x05 0x65

Language Write Español 0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x04 0x65 Language Write РУССКИЙ 0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x05 0x66 Language Write Language Write Language Write Language Write Language Write Swedish 0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x0a 0x6B Language Write Dutch 0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x0b 0x6C Language Write Turkish 0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x0c 0x6D Language Write Czech 0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x0d 0x6E Language Write Portuguese 0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x0e 0x6F Language Write Thai 0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x0f 0x70 Language Write Polish 0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x10 0x71 Language Write Finnish 0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x11 0x72 Language Write Arabic 0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x12 0x73 Language Write Indonesia 0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x13 0x74

繁體中文

简体中文

日本語

한국어한국어

0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x06 0x67 0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x07 0x68 0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x08 0x69 0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x09 0x6A

Language Write Hindi 0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x14 0x75 Language Write Vie 0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x15 0x76 Language Write Greek 0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x16 0x77 Language Read Status 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x15 0x00 0x62 Light Source Usage

Time

Write Reset to ZERO 0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x01 0x00 0x62

Page 84

Function Type Action Command

Light Source Usage Time

HDMI Format Write RGB 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x28 0x00 0x85 HDMI Format Write YUV 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x28 0x01 0x86 HDMI Format Write Auto 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x28 0x02 0x87 HDMI Format Read Status 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x11 0x28 0x86 HDMI Range Write Enhanced/Full 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x29 0x00 0x86 HDMI Range Write Normal/Limited 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x29 0x01 0x87 HDMI Range Write Auto 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x29 0x02 0x88 HDMI Range Read Status 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x11 0x29 0x87 CEC Write OFF 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x2B 0x00 0x88 CEC Write ON 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x2B 0x01 0x89 CEC Read Status 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x11 0x2B 0x89 Error status Read Status 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x0C 0x0D 0x66

Read Get Equivalent

light source

Hour

Read Get Usage Time 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x15 0x0A 0x6C

0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x15 0x01 0x63

Remote Control Code

Write code 1 0x06 0x14 0x00 0x04 0x00 0x34 0x0C 0x48 0x00 0xA0

Write code 2 0x06 0x14 0x00 0x04 0x00 0x34 0x0C 0x48 0x01 0xA1

Write code 3 0x06 0x14 0x00 0x04 0x00 0x34 0x0C 0x48 0x02 0xA2

Write code 4 0x06 0x14 0x00 0x04 0x00 0x34 0x0C 0x48 0x03 0xA3

Write code 5 0x06 0x14 0x00 0x04 0x00 0x34 0x0C 0x48 0x04 0xA4

Write code 6 0x06 0x14 0x00 0x04 0x00 0x34 0x0C 0x48 0x05 0xA5

Write code 7 0x06 0x14 0x00 0x04 0x00 0x34 0x0C 0x48 0x06 0xA6

Write code 8 0x06 0x14 0x00 0x04 0x00 0x34 0x0C 0x48 0x07 0xA7

Read Status 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x0C 0x48 0xA1

Over Scan Write OFF 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x33 0x00 0x90 Over Scan Write Value 1 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x33 0x01 0x91 Over Scan Write Value 2 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x33 0x02 0x92 Over Scan Write Value 3 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x33 0x03 0x93 Over Scan Write Value 4 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x33 0x04 0x94

Page 85

Function Type Action Command

Over Scan Write Value 5 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x33 0x05 0x95 Over Scan Read Get Value 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x11 0x33 0x91 Remote Key Write Menu 0x02 0x14 0x00 0x04 0x00 0x34 0x02 0x04 0x0F 0x61 Remote Key Write Exit 0x02 0x14 0x00 0x04 0x00 0x34 0x02 0x04 0x13 0x65 Remote Key Write Top 0x02 0x14 0x00 0x04 0x00 0x34 0x02 0x04 0x0B 0x5D Remote Key Write Bottom 0x02 0x14 0x00 0x04 0x00 0x34 0x02 0x04 0x0C 0x5E Remote Key Write Left 0x02 0x14 0x00 0x04 0x00 0x34 0x02 0x04 0x0D 0x5F Remote Key Write Right 0x02 0x14 0x00 0x04 0x00 0x34 0x02 0x04 0x0E 0x60 Remote Key Write Source 0x02 0x14 0x00 0x04 0x00 0x34 0x02 0x04 0x04 0x56 Remote Key Write Enter 0x02 0x14 0x00 0x04 0x00 0x34 0x02 0x04 0x15 0x67 Remote Key Write Auto 0x02 0x14 0x00 0x04 0x00 0x34 0x02 0x04 0x08 0x5A AMX Write AMX response AMX Operating

temperature Light source mode

cycle Audio Mode Write Movie 0x06 0x14 0x00 0x04 0x00 0x34 0x14 0x05 0x04 0x69 Audio Mode Write Music 0x06 0x14 0x00 0x04 0x00 0x34 0x14 0x05 0x05 0x6A Audio Mode Write Speech 0x06 0x 14 0x00 0x04 0x00 0x34 0x14 0x05 0x01 0x66 Audio Mode Write User 0x06 0x14 0x00 0x04 0x00 0x34 0x14 0x05 0x06 0x6B Audio Mode Read Status 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x14 0x05

S/PDIF Write On 0x06 0x14 0x00 0x04 0x00 0x34 0x14 0x05 0x07 0x6C S/PDIF Write Off 0x06 0x14 0x00 0x04 0x00 0x34 0x14 0x05 0x08 0x6D S/PDIF Read Status 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x11 0x38

Frame Interpolation

Read Get Value 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x15 0x03 0x65

Write Cycle 0x06 0x14 0x00 0x04 0x00 0x34 0x13 0x36 0x00 0x95

0x66

0x96

Write Low 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x2D 0x00 0x8A

Write Mid 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x2D 0x01 0x8B

Frame Interpolation

Gamma Write 1.8 0x02 0x14 0x00 0x04 0x00 0x34 0x05 0xCA 0x00 0x1B Gamma Write 2 0x02 0x14 0x00 0x04 0x00 0x34 0x05 0xCA 0x01 0x1C Gamma Write 2.2 0x02 0x14 0x00 0x04 0x00 0x34 0x05 0xCA 0x02 0x1D Gamma Write 2.35 0x02 0x14 0x00 0x04 0x00 0x34 0x05 0xCA 0x03 0x1E Gamma Write 2.5 0x02 0x14 0x00 0x04 0x00 0x34 0x05 0xCA 0x04 0x1F

Write High 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x2D 0x02 0x8C

Read Status 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x11 0x2D

0x8B

Page 86

Function Type Action Command

Gamma Write sRGB 0x02 0x14 0x00 0x04 0x00 0x34 0x05 0xCA 0x05 0x20 Gamma Write Cubic 0x02 0x14 0x00 0x04 0x00 0x34 0x05 0xCA 0x06 0x21 Gamma Read Get Value 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x05 0xCA

0x1C Lens Focus Write Right 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x37 0x01 0x95 Lens Focus Write Left 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x37 0x00 0x94

Page 87

Glossary

This section describes the standard glossary of terms used in projector models. All terms are listed in alphabetical order.

NOTE: Some terms may not be applicable to your projector.

Aspect Ratio

Refers to the ratio of the image width to the image height.

Auto Sync

Built-in intelligent auto adjustment function that will re-adjust the frequency and clock values to provide the best picture quality.

Blank

Temporarily hide the screen image to maintain audience focus when necessary.

Brightest Mode

Maximizes the brightness of the projected image. This mode is ideal for

environments where extra-high brightness is required, such as using the projector in well lit rooms.

Brightness

Adjusts brightness levels of the screen image.

CEC (Consumer Electronics Control)

Synchronizes power on/off operation via HDMI connection. That is, if a device that also supports CEC function is connected to the HDMI input of the projector, when the projector’s power is turned off, the power of the connected device will also be turned off automatically. When the power of the connected device is turned on, the projector’s power will be turned on automatically.

Color

Adjusts the color saturation.

Color Mode

The projector is preset with several predefined color modes to suit operating, environmental, and input source needs.

Page 88

Color Temp.

Allows users to select specific color temperature settings to further customize their viewing experience.

Projector Default Projector Original Status

9300K 7500K

6500K

Contrast

Adjusts the difference between the image background (black level) and the foreground (white level).

Focus Ring

Manually improve the clarity of the projected image.

Gamma

Allows the user to manually select the greyscale curve of the projector.

HDMI Range

Allows the user to select HDMI greyscale range between 0~255 (Enhanced

Images appear bluish white. Default color temperature. Images maintain a normal white appearance. Recommended for general use.

Images appear reddish white.

Range) , 16~235 (Normal Range) or Auto by the signal type detected.

High Altitude Mode

Optional mode for users who live in an environment between 1,500 m and 3,000 m above sea level, and the temperature is between 5° C and 25° C. Activating it will improve projector cooling and performance.

INFORMATION

Displays the timing mode (video signal input), the projector model number, the serial number, and the ViewSonic® website URL.

Input Select

Toggles between the various input options that are available for the projector.

Keystone

The distortion of an image caused by projecting it onto an angled surface. It can be adjusted via the [ / / / ] Keystone Keys.

Page 89

Light Source Settings

The projector’s light source information and settings can be viewed and adjusted by viewing the “Light Source Hours Information” or adjusting the “Light source Mode”.

Lens Shift

The projector’s lens can be shifted vertically by adjusting the “Lens Shift” menu.

Movie Mode

A Color Mode appropriate for playing colorful movies, video clips from digital cameras, or DVs through the PC input. Best for a low light environment.

OverScan

Refers to a cropped image on your monitor’s screen. A setting on your monitor zooms in on movie content, so that you cannot see the outermost edges of the film.

Pattern

Projects a grid to be used for image adjustment and fine-tuning.

Projector Position

The projected image can be adjusted based on the installation location of the projector, i.e. ceiling or rear projection installation.

RS-232

A standard code for serial communication transmission of data, used for connection to other devices or controller vis serial port or LAN port.

Sharpness

Adjusts the picture quality.

Standard Mode

A Color Mode that is designed for normal viewing circumstances in a daylight environment.

Zoom Ring

Manually adjust the size of the projected image.

Page 90

Troubleshooting

Common Problems

This section describes some common problems that you may experience when using the projector.

Problem Possible Solutions

The projector does not turn on • Ensure the power cord is properly aached to the

projector and to the power outlet.

• If the cooling process has not completed, please

wait unl it has nished then try to turn on the

projector again.

• If the above does not work, try another power outlet or another electrical device with the same power outlet.

There is no picture • Ensure the video source cable is connected properly,

and that the video source is turned on.

• If the input source is not selected automacally, select the correct source with the Source key on either the projector or the remote control.

The image is blurred • Adjusng the Focus Ring will help correctly focus the

projecon lens.

• Ensure the projector and screen are aligned properly. If necessary, adjust the height of the projector as

well as the projecon angle and direcon.

The remote control does not work

• Ensure there are no obstacles between the remote control and projector; and that they are within 8 m

(26 ) of each other.

• The baeries may be out of power, please check and replace if necessary.

Page 91

LED Indicators

Light Status and Description

Power

Green

Flashing

Green Off Off Powering up Green Off Off Normal operation

Off Off Stand-by mode

Green

Flashing

Red Off Off Downloading

Green Green Green Burn in off

Off Off Normal power-down cooling

Light source

Green

Flashing

Off Off Red Light source error in normal operation

Green Off Red Color wheel start has failed

Off Red First light source-lit error cooling

Heating/Cooling

Off Red Off Fan 1 error (actual fan speed is outside the desired speed). Off Red Red Fan 2 error (actual fan speed is outside the desired speed).

Off Red Green Fan 3 error (actual fan speed is outside the desired speed). Off Red Orange Fan 4 error (actual fan speed is outside the desired speed).

Red

Flashing

Red Off Fan 5 error (actual fan speed is outside the desired speed).

Red

Flashing

Red Red Red Thermal sensor 1 open error (the remote diode has an

Red Red Green Thermal sensor 2 open error (the remote diode has an

Green Red Red Thermal sensor 1 short error (the remote diode has an

Off Red Green Thermal sensor 2 short error (the remote diode has an

Orange Red Red Temperature 1 error (over limited temperature). Orange Red Green Temperature 2 error (over limited temperature).

Off Green Red Fan IC #1 I2C connection error.

Red

Flashing

Off Fan 6 error (actual fan speed is outside the desired speed).

open-circuit condition).

Page 92

Maintenance

General Precautions

• Make sure the Projector is turned o and the power cable is unplugged from the power outlet.

• Never remove any parts from the Projector. Contact ViewSonic® or a reseller when any part of the Projector needs replacing.

• Never spray or pour any liquid directly onto the case.

• Handle the Projector with care, as a darker-colored projector, if scued, may show marks more clearly than a lighter-colored projector.

Cleaning the Lens

• Use a canister of compressed air to remove dust.

• If the lens is sll not clean, use lens-cleaning paper or moisten a so cloth with lens cleaner and gently wipe the surface.

CAUTION: Never rub the lens with abrasive materials.

Cleaning the Case

• Use a so, lint-free, dry cloth to remove dirt or dust.

• If the case is sll not clean, apply a small amount of non-ammonia, non-alcohol

based, mild non-abrasive detergent onto a clean, so, lint-free cloth, then wipe

the surface.

CAUTION: Never use wax, alcohol, benzene, thinner, or other chemical detergents.

Storing the Projector

If you intend to store the Projector for an extended period of time:

• Ensure the temperature and humidity of the storage area are within the recommend range.

• Retract the adjuster foot completely.

• Remove the baeries from the Remote Control.

• Pack the Projector in its original packaging or equivalent.

Disclaimer

• ViewSonic® does not recommend the use of any ammonia or alcohol-based cleaners on the lens or case. Some chemical cleaners have been reported to damage the lens and/or case of the projector.

• ViewSonic® will not be liable for damage resulng from use of any ammonia or alcohol-based cleaners.

Page 93

Light Source Information

This section will provided a better understanding of your projector’s light source.

Light Source Hour

When the projector is being used, the duration (in hours) of light source usage is automatically calculated by the built-in timer.

To obtain the light source hour information:

1. Press Menu to open the OSD Menu and go to: Advanced > Light Source Settings

> Light Source Hours Information.

2. Press Enter and the Light Source Hours Information page will appear.

3. Press Exit to leave the menu. Extending Light Source Life

To prolong light source life, you can adjust the following settings in the OSD Menu.

Setting Light Source Mode

Setting the projector in Eco, Dynamic Black 1, or Dynamic Black 2 mode reduces system noise, power consumption, and extends the light sources operational life.

Light source Mode Description

Normal Provides full light source brightness.

Eco

Dynamic Black 1

Dynamic Black 2

Custom

Reduces light source power consumption by 30% and lowers brightness, and decreases fan noise.

Reduces light source power consumption by up to 95% depending on the content's brightness level.

Reduces light source power consumption by up to 60% depending on the content’s brightness level.

Allows you to adjust the light source power to extend the light source life and decreases the fan noise.

To set the Light Source Mode, open the OSD Menu and go to: Advanced >

Light Source Settings > Light Source Mode and press / to select and press Enter.

Setting Auto Power Off

This allows the projector to turn off automatically after a set period of time once no input source is detected.

Open the OSD Menu and go to: POWER MANAGEMENT > Smart Energy > Auto Power Off and press

to disable or adjust the time.

Page 94

Regulatory and Service Information

Compliance Information

This section addresses all connected requirements and statements regarding regulations. Confirmed corresponding applications shall refer to nameplate labels and relevant markings on the unit.

FCC Compliance Statement

This device complies with part 15 of FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

WARNING: You are cauoned that changes or modicaons not expressly

approved by the party responsible for compliance could void your authority to operate the equipment.

Industry Canada Statement

CAN ICES-3 (B)/NMB-3(B)

CE Conformity for European Countries

The device complies with the EMC Directive 2014/30/EU and Low Voltage Directive 2014/35/EU.

Page 95

The following information is only for EU-member states:

The mark shown to the right is in compliance with the Waste Electrical and Electronic Equipment Directive 2012/19/EU (WEEE). The mark indicates the requirement NOT to dispose of the equipment as unsorted municipal waste, but use the return and collection systems according to local law.

Declaration of RoHS2 Compliance

This product has been designed and manufactured in compliance with Directive 2011/65/EU of the European Parliament and the Council on restriction of the use of certain hazardous substances in electrical and electronic equipment (RoHS2 Directive) and is deemed to comply with the maximum concentration values issued by the European Technical Adaptation Committee (TAC) as shown below:

Substance Proposed Maximum

Concentration

Cadmium (Cd) 0.01% < 0.01% Lead (Pb) 0.1% < 0.1% Mercury (Hg) 0.1% < 0.1% Hexavalent Chromium (Cr6+) 0.1% < 0.1% Polybrominated biphenyls (PBB) 0.1% < 0.1% Polybrominated diphenyl esthers (PBDE) 0.1% < 0.1% Bis(2-Ethylhexyl) phthalate (DEHP) 0.1% < 0.1% Benzyl butyl phthalate (BBP) 0.1% < 0.1% Dibutyl phthalate (DBP) 0.1% < 0.1% Diisobutyl phthalate (DIBP) 0.1% < 0.1%

Actual

Concentration

Certain components of products as stated above are exempted under the Annex III of the RoHS2 Directives as noted below:

• Mercury in cold cathode fluorescent lamps and external electrode fluorescent lamps (CCFL and EEFL) for special purposes not exceeding (per lamp):

» Short length (500 mm): maximum 3.5 mg per lamp. » Medium length (> 500 mm and 1,500 mm): maximum 5 mg per lamp. » Long length (> 1,500 mm): maximum 13 mg per lamp.

• Lead in glass of cathode ray tubes.

• Lead in glass of fluorescent tubes not exceeding 0.2% by weight.

• Lead as an alloying element in aluminum containing up to 0.4% lead by weight.

• Copper alloy containing up to 4% lead by weight.

• Lead in high melting temperature type solders (i.e. lead-based alloys containing 85% by weight or more lead).

• Electrical and electronic components containing lead in a glass or ceramic other than dielectric ceramic in capacitors, e.g. piezoelectronic devices, or in a glass or ceramic matrix compound.

Page 96

Indian Restriction of Hazardous Substances

Restriction on Hazardous Substances statement (India). This product complies with the “India E-waste Rule 2011” and prohibits use of lead, mercury, hexavalent chromium, polybrominated biphenyls or polybrominated diphenyl ethers in concentrations exceeding 0.1 weight % and 0.01 weight % for cadmium, except for the exemptions set in Schedule 2 of the Rule.

Product Disposal at End of Product Life

ViewSonic® respects the environment and is committed to working and living green. Thank you for being part of Smarter, Greener Computing. Please visit the ViewSonic® website to learn more.

USA & Canada:

http://www.viewsonic.com/company/green/recycle-program/

Europe:

http://www.viewsoniceurope.com/uk/support/recycling-information/

Page 97

Copyright Information

Microsoft, Windows, and the Windows logo are registered trademarks of Microsoft Corporation in the United States and other countries.

ViewSonic® and the three birds logo are registered trademarks of ViewSonic® Corporation.

VESA is a registered trademark of the Video Electronics Standards Association. DPMS and DDC are trademarks of VESA.

Disclaimer: ViewSonic® Corporation shall not be liable for technical or editorial errors or omissions contained herein; nor for incidental or consequential damages resulting from furnishing this material, or the performance or use of this product.

In the interest of continuing product improvement, ViewSonic® Corporation reserves the right to change product specifications without notice. Information in this document may change without notice.

No part of this document may be copied, reproduced, or transmitted by any means, for any purpose without prior written permission from ViewSonic® Corporation.

LS600W_UG_ENG_1a_20200820

Page 98

Customer Service

For technical support or product service, see the table below or contact your reseller.

NOTE: You will need the product’s serial number.

Country/ Region Website Country/ Region Website

Asia Pacific & Africa

Australia

中国 (China)

Hong Kong (English)

Indonesia

日本 (Japan)

Malaysia

Myanmar

New Zealand

Philippines

臺灣 (Taiwan)

Việt Nam

www.viewsonic.com/au/

www.viewsonic.com.cn

www.viewsonic.com/hk-en/

www.viewsonic.com/id/

www.viewsonic.com/jp/

www.viewsonic.com/my/

www.viewsonic.com/mm/

www.viewsonic.com/nz/

www.viewsonic.com/ph/

www.viewsonic.com/tw/

www.viewsonic.com/vn/

Bangladesh

香港 (繁體中文)

India

Israel

Korea

Middle East

Nepal

Pakistan

Singapore

ประเทศไทย

South Africa &

Maurius

www.viewsonic.com/bd/

www.viewsonic.com/hk/

www.viewsonic.com/in/

www.viewsonic.com/il/

www.viewsonic.com/kr/

www.viewsonic.com/me/

www.viewsonic.com/np/

www.viewsonic.com/pk/

www.viewsonic.com/sg/

www.viewsonic.com/th/

www.viewsonic.com/za/

Americas

United States

Lan America

Europe

Deutschland

Россия

Türkiye

United Kingdom

www.viewsonic.com/us

www.viewsonic.com/la

www.viewsonic.com/eu/

www.viewsonic.com/de/

www.viewsonic.com/ru/

www.viewsonic.com/tr/

www.viewsonic.com/uk/

Canada

France

Қазақстан

España

Україна

www.viewsonic.com/us

www.viewsonic.com/fr/

www.viewsonic.com/kz/

www.viewsonic.com/es/

www.viewsonic.com/ua/

Page 99

Limited Warranty

ViewSonic® Projector

What the warranty covers:

ViewSonic warrants its products to be free from defects in material and workmanship, under normal use, during the warranty period. If a product proves to be defective in material or workmanship during the warranty period, ViewSonic will, at its sole option, repair or replace the product with a like product. Replacement product or parts may include remanufactured or refurbished parts or components.

Limited Three (3) year General Warranty

Subject to the more limited one (1) year warranty set out below, North and South America: Three (3) years warranty for all parts excluding the lamp, three (3) years for labor, and one (1) year for the original lamp from the date of the first consumer purchase. Other regions or countries: Please check with your local dealer or local ViewSonic office for the warranty information.

Limited One (1) year Heavy Usage Warranty:

Under heavy usage settings, where a projector’s use includes more than fourteen (14) hours average daily usage, North and South America: One (1) year warranty for all parts excluding the lamp, one (1) year for labor, and ninety (90) days for the original lamp from the date of the first consumer purchase; Europe: One (1) year warranty for all parts excluding the lamp, one (1) year for labor, and ninety (90) days for the original lamp from the date of the first consumer purchase. Other regions or countries: Please check with your local dealer or local ViewSonic office for the warranty information. Lamp warranty subject to terms and conditions, verification and approval. Applies to manufacturer’s installed lamp only. All accessory lamps purchased separately are warranted for 90 days.

Who the warranty protects:

This warranty is valid only for the first consumer purchaser.

9999

Page 100

What the warranty does not cover:

1. Any product on which the serial number has been defaced, modied or removed.

2. Damage, deterioration, failure, or malfunction resulting from:

a. Accident, abuse, misuse, neglect, fire, water, lightning, or other acts of nature,

improper maintenance, unauthorized product modification, or failure to follow

instructions supplied with the product. b. Operation outside of product specifications. c. Operation of the product for other than the normal intended use or not under

normal conditions. d. Repair or attempted repair by anyone not authorized by ViewSonic. e. Any damage of the product due to shipment. f. Removal or installation of the product. g. Causes external to the product, such as electric power fluctuations or failure. h. Use of supplies or parts not meeting ViewSonic’s specifications. i. Normal wear and tear. j. Any other cause which does not relate to a product defect.

3. Removal, installation, and set-up service charges.

How to get service:

1. For informaon about receiving service under warranty, contact ViewSonic Customer Support (please refer to “Customer Support” page). You will need to provide your product’s serial number.

2. To obtain warranted service, you will be required to provide (a) the original dated sales slip, (b) your name, (c) your address, (d) a description of the problem, and (e) the serial number of the product.

3. Take or ship the product freight prepaid in the original container to an authorized ViewSonic service center or ViewSonic.

4. For additional information or the name of the nearest ViewSonic service center, contact ViewSonic.

Limitation of implied warranties:

There are no warranties, express or implied, which extend beyond the description contained herein including the implied warranty of merchantability and fitness for a particular purpose.

100

ViewSonic LS600W operation manual

Specifications and Main Features

Frequently Asked Questions

User Manual

Safety Precautions - General

Introduction

Product Overview

Projector

Controls and Functions

Connection Ports

Remote Control

Controls and Functions

Remote Control Effective Range

Replacing the Remote Control Batteries

Initial Setup

Projection Dimensions

16:10 Image on a 16:10 Screen

16:10 Image on a 4:3 Screen

Mounting the Projector

Preventing Unauthorized Use

Using the Security Slot

Using the Password Function

Setting a Password

Changing the Password

Disabling the Password Function

Forgetting the Password

Password Recall Procedure

Locking the Control Keys

Making Connections

Connecting to Video Sources

HDMI Connection

Composite Video Connection

Connecting to Computer Sources

VGA Connection

VGA Out Connection

Connecting to Audio

Operation

Shutting Down the Projector

Selecting an Input Source

Adjusting the Projected Image

Adjusting the Projector's Height and Projection Angle

Auto-Adjusting the Image

Fine-Tuning the Image Size and Clarity

Correcting Keystone

Hiding the Image

Controlling the Projector through a LAN Environment

Configuring the LAN Control Settings

Controlling the Projector through a Web Browser

About Crestron e-Control®

PJLink™, SNMP, AMX and Xpanel Formats Supported

Menu Functions

On-Screen Display (OSD) Menu Tree

DISPLAY Menu

IMAGE Menu

POWER MANAGEMENT Menu

BASIC Menu

ADVANCED Menu

SYSTEM Menu

INFORMATION Menu

Appendix

Projector Dimensions

Timing Chart

Analog RGB

HDMI (PC)

HDMI (Video)

Video/S-Video

Component video

IR Control Table

Address Code

RS-232 Command Table

Pin Assignment

Interface

Command Table

Glossary

Troubleshooting

Common Problems

LED Indicators

Maintenance

General Precautions

Cleaning the Lens