Vieworks FXRD-1012NAW User Manual

Download

VIVIX-S 1012N User Manual

Under copyright laws, this manual should not be reproduced, in whole or in part, without the written

permission of Vieworks.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two

conditions: (1) This device may not cause harmful interference, and (2) this device must accept

any interference received, including interference that may cause undesired operation.

Changes or modifications not expressly approved by the party responsible for compliance could

void the user’s authority to operate the equipment. This transmitter must not be co-located or

operated in conjunction with any other antenna or transmitter.

5150~5250 MHz band is restricted to indoor operations only. (for FCC and CE)

FCC ID: PFRFXRD-1012NAW

FCC ID: PFRFXRS-03A

FCC ID: PFRFXRS-04A

FCC ID: PFRFXRD-1012NAW, PFRFXRS-03A and PFRFXRS-04A in the RF module do not use DFS

band. *RF modue FCC ID:RYK-WPEA-121N.

Host device of the approved module shall be marked with the following item:

Contains Transmitter Module FCC ID:RYK-WPEA-121N

VIVIX-S 1012N User Manual

Contents

1. Instruction ......................................................................................................................................... 6

1.1 Document Guide ..................................................................................................................................... 7

1.1.1 Caution Information ..................................................................................................................................................... 7

1.1.2 Target ................................................................................................................................................................................... 7

1.1.3 Symbols .............................................................................................................................................................................. 7

1.1.4 Notations ........................................................................................................................................................................... 8

1.1.5 Contact Department ..................................................................................................................................................... 8

1.2 Product Use Guide .................................................................................................................................. 9

1.2.1 Product Usage ................................................................................................................................................................. 9

1.2.2 Disclaimer .......................................................................................................................................................................... 9

1.2.3 Product Disposal ..........................................................................................................................................................10

1.2.4 Trademarks ......................................................................................................................................................................10

1.3 Safety Instruction .................................................................................................................................. 11

1.3.1 Management and Authority ...................................................................................................................................11

1.3.2 Power Supply .................................................................................................................................................................11

1.3.3 Handling ...........................................................................................................................................................................12

1.3.4 Battery Pack and Charger ........................................................................................................................................13

1.3.5 Environment of Use ....................................................................................................................................................14

1.3.6 Problem Management ...............................................................................................................................................15

1.3.7 Maintenance and Inspection ..................................................................................................................................15

1.4 Product Usage Guide ............................................................................................................................ 16

1.4.1 Calibration .......................................................................................................................................................................16

1.4.2 Length Measurement .................................................................................................................................................16

1.4.3 Left/Right Marker.........................................................................................................................................................16

1.4.4 Image Backup ................................................................................................................................................................16

1.4.5 Use Limitations .............................................................................................................................................................17

1.4.6 Disposal ............................................................................................................................................................................17

1.4.7 Pediatric Application ..................................................................................................................................................17

1.4.8 Before Exposure ............................................................................................................................................................17

1.4.9 During Exposure ...........................................................................................................................................................18

1.4.10 Operating and Storage Environment .................................................................................................................18

1.4.11 Others................................................................................................................................................................................18

2. Product ............................................................................................................................................. 19

2.1 Overview ................................................................................................................................................. 20

2.1.1 Features [TBD] ...............................................................................................................................................20

Rev.1.0

Page 2 of 109 RA14-14B-011

VIVIX-S 1012N User Manual

2.2 Product Components ............................................................................................................................ 21

2.2.1 Detector............................................................................................................................................................................21

2.2.2 VIVIX SCU (VIVIX System Control Unit) .............................................................................................................21

2.2.3 Battery & Charger .......................................................................................................................................................22

2.2.4 Data ....................................................................................................................................................................................22

2.2.5 Other Accessories ........................................................................................................................................................22

2.3 VIVIX-S 1012N Detector ...................................................................................................................... 24

2.3.1 Specifications .................................................................................................................................................................24

2.3.2 Drawing Sheet ...............................................................................................................................................................25

2.3.3 Functions .........................................................................................................................................................................26

2.3.4 Deco Sheet [TBD] ......................................................................................................................................27

2.3.5 Wireless Communication..........................................................................................................................................27

2.3.6 Use Environment ..........................................................................................................................................................28

2.4 VIVIX SCU (VIVIX System Control Unit) ............................................................................................ 29

2.4.1 Specifications .................................................................................................................................................................29

2.4.2 Drawing Sheet ...............................................................................................................................................................30

2.4.3 Function – VIVIX SCU Basic ....................................................................................................................................31

2.4.4 Function – VIVIX SCU Mini .....................................................................................................................................33

2.5 Battery Pack ........................................................................................................................................... 35

2.5.1 Specifications .................................................................................................................................................................35

2.5.2 Drawing Sheet ...............................................................................................................................................................35

2.6 Battery Charger ..................................................................................................................................... 36

2.6.1 Specifications .................................................................................................................................................................36

2.6.2 Drawing Sheet ...............................................................................................................................................................36

2.7 Others [TBD] .......................................................................................................................... 37

2.7.1 X-ray Generator (Recommended Exposure Condition)..............................................................................37

2.7.2 Recommended Specification of Workstation (PC) .......................................................................................37

2.7.3 Recommended Specification of Grid ..................................................................................................................37

3. System Configuration ................................................................................................................... 39

3.1 Detector Connection Methods ........................................................................................................... 40

3.1.1 Wireless Connection ...................................................................................................................................................40

3.1.2 Wired Connection ........................................................................................................................................................41

3.2 Diagram ................................................................................................................................................... 42

3.2.1 Block Diagram ...............................................................................................................................................................42

3.2.2 Wiring Diagram ............................................................................................................................................................42

Rev.1.0

Page 3 of 109 RA14-14B-011

VIVIX-S 1012N User Manual

3.3 System Configuration ........................................................................................................................... 43

3.3.1 AP Mode (SCU AP Mode)........................................................................................................................................43

3.3.2 Tether Interface Mode ...............................................................................................................................................44

3.3.3 External AP Mode ........................................................................................................................................................45

3.3.4 Detector AP Mode ......................................................................................................................................................46

3.3.5 Detector Stand-Alone Mode ..................................................................................................................................47

3.4 Generator Interface Mode ................................................................................................................... 48

3.4.1 AED (Auto Exposure Detection) Interface Mode ..........................................................................................48

3.4.2 DR Trigger Interface Mode .....................................................................................................................................49

3.5 Configuring DR Trigger Interface Mode ........................................................................................... 50

3.5.1 Trigger Interface Way .................................................................................................................................................50

3.5.2 Packet Trigger ................................................................................................................................................................50

3.5.3 Line Trigger .....................................................................................................................................................................51

3.5.4 EXT_INF Port Pin Map ...............................................................................................................................................52

3.5.5 Input / Output Circuit ................................................................................................................................................54

4. Installation [TBD] .............................................................................................................. 55

4.1 Battery Pack [TBD] ................................................................................................................... 56

4.1.1 How to insert a battery pack .................................................................................................................................56

4.1.2 How to datach a battery pack...............................................................................................................................57

4.1.3 How to charge a battery pack [TBD] ..................................................................................................58

4.2 Product Installation .............................................................................................................................. 60

4.2.1 Connecting Devices [TBD] .......................................................................................................................60

4.2.2 Booting up SCU [TBD] ...............................................................................................................................62

4.2.3 Booting up the Detector ..........................................................................................................................................62

4.2.4 Checking Status LED of Detector [TBD] ............................................................................................63

4.3 Software Installation ............................................................................................................................. 64

4.3.1 Software Classification [TBD] ..................................................................................................................64

4.3.2 Software Installation ...................................................................................................................................................64

4.4 Windows Environment Setting ........................................................................................................... 65

Rev.1.0

Page 4 of 109 RA14-14B-011

VIVIX-S 1012N User Manual

4.4.1 Network Configuration [TBD] .................................................................................................................65

4.4.2 Disabling Sleep Mode of Monitor .......................................................................................................................69

5. Setting [TBD] ..................................................................................................................... 70

6. Calibration [TBD] .............................................................................................................. 74

7. Diagnosis, Inspection and Maintenance [TBD] ............................................................ 80

8. Troubleshooting [TBD] .................................................................................................... 89

9. Regulatory Information ................................................................................................................ 94

9.1 Medical Equipment Safety Standards ............................................................................................... 95

9.1.1 Medical Equipment Classification ........................................................................................................................95

9.1.2 Product Safety Standard ...........................................................................................................................................95

9.2 Radio Frequency Compliance Information ....................................................................................... 97

9.2.1 FCC Compliance ...........................................................................................................................................................97

9.3 Labels and Symbols .............................................................................................................................. 98

9.3.1 Label ..................................................................................................................................................................................98

9.3.2 Product Serial Number........................................................................................................................................... 100

9.3.3 Product Symbols ....................................................................................................................................................... 101

9.4 Guidance and Manufacturer’s Declaration for EMC ..................................................................... 102

9.4.1 Electromagnetic Emissions ................................................................................................................................... 102

9.4.2 Electromagnetic Immunity .................................................................................................................................... 103

10. Information ................................................................................................................................ 106

10.1 Service Information ........................................................................................................................ 107

10.1.1 Product Lifetime ........................................................................................................................................................ 107

10.1.2 Regular Inspection and Maintenance ............................................................................................................. 107

10.1.3 Repair ............................................................................................................................................................................. 107

10.1.4 Replacement Parts Support ................................................................................................................................. 107

10.1.5 Consumables ............................................................................................................................................................... 107

10.2 Warranty ............................................................................................................................................ 108

10.3 Revision History ............................................................................................................................... 109

Rev.1.0

Page 5 of 109 RA14-14B-011

VIVIX-S 1012N User Manual

1. Instruction

This section gives basic information of this manual and products with the safety guide.

Document Guide

Product Use Guide

Safety Instruction

Product Operation Guide

Rev.1.0

Page 6 of 109 RA14-14B-011

1.1 Document Guide

This User Manual explains how to use the VIVIX-S 1012N detector made by Vieworks, X-ray interface unit,

and other peripheral equipment. With this user manual, you can install, set and manage the VIVIX-S 1012N

wired/wireless detectors as well as use its various functions.

1.1.1 Caution Information

If the user is not fully aquainted with this manual, the product can be malfunctioned or unsuspected

problem can be happened due to carelessness. To prevent any medical accidents, the user should fully

understand the instructions of this manual before operating this product.

1.1.2 Target

This manual is intended for service enginneers who install and set the VIVIX-S 1012N detector.

VIVIX-S 1012N User Manual

1.1.3 Symbols

This product should be operated under the safety instructions with the warning or caution symbol in this

manual. It is important for you to read and understand the contents with the following symbol for

operating the products safely.

Caution and Warning Symbol

 This symbol is used to indicate a potentially hazardous situation which may cause death,

personal injury or substantial property damage if the instructions are ignored. Be sure to

understand the instructions of this symbol for the safe operation.

Information Symbol

 This symbol is used to indicate reference and complementary information related to the

product. Users should read the instructions of this symbol carefully.

Symbol for Change

 This symbol is indicated in the cases below.

 Items under consideration for adding, deleting or revising contents.  Items ready to review for the expected product change.  Items need a final review and approval.  Items which need to improve sentences or images.

Rev.1.0

Page 7 of 109 RA14-14B-011

1.1.4 Notations

Bold Types

We applied bold font style to the words which indicated products terms, or the words and sentences which

are needed to transmit clear meaning to the customers. This helps you to easily distinguish the words from

other technical ones for explaining functions.

1.1.5 Contact Department

For any comments or inquiries regarding this document, contact via email below.

Item Contents

Department Technical Support Division in Vieworks

E-mail techsupport@vieworks.com

VIVIX-S 1012N User Manual

Rev.1.0

Page 8 of 109 RA14-14B-011

1.2 Product Use Guide

This chapter provides instructions about the use of product and disposal as well as the liability limit of

Vieworks.

1.2.1 Product Usage

1 Only a physician or a legally certified operator should use this product.

2 The equipment should be kept in a safe and operable condition by maintenance personnel.

3 Observe the contents written in this user manual when installing and using this product.

4 Use only specifications of computers and image display monitors recommended by this user manual.

5 Use only the dedicated cables provided with this product.

6 For details about installing and using this product, consult your sales representative or a distributor.

VIVIX-S 1012N User Manual

1.2.2 Disclaimer

1 In no event shall Vieworks be liable for damage or loss arising from a fire, earthquake, any intentional

or negligent action by users.

2 In no event shall Vieworks be liable for damage or loss arising from any trial usage, or other usage

under abnormal conditions.

3 In no event shall Vieworks be liable for personal physical harm or property damage that is sustained

when the instructions of this manual are not followed.

4 In no event shall Vieworks be liable for direct or indirect consequential damages arising from the use of

this product.

5 In no event shall Vieworks be liable for any damage arising from moving, alteration, inspection or repair

by a person other than authorized service engineers.

6 In no event shall Vieworks be liable for loss of image data for any reason.

7 Roentgenography, image processing, image reading, and image data storage must be performed in

accordance with the laws of the country or region in which the product is being used.

8 The user is responsible for maintaining the privacy of image data acquired from this product.

9 It is the responsibility of the attending physicians to provide medical care services. Vieworks will not be

liable for faulty diagnoses.

10 Specifications, composition, and appearance of this product may change without prior notice.

Rev.1.0

Page 9 of 109 RA14-14B-011

or to an authorized collection site for

1.2.3 Product Disposal

Disposal of this product in an unlawful manner may have a negative impact on human health and the

environment. When disposing this product, therefore, be absolutely sure to follow the procedure which is in

conformity with the laws and regulations applicable in your area.

European Union (and EEA*) only

This symbol indicates that this product is not to be disposed with your household waste,

according to the WEEE Directive (2002/96/EC) and your national law.

This product should be handed over to a designated collection point, e.g., on an authorized

one-for-one basis when you buy a new similar product

recycling electrical and electronic equipment (EEE). Improper handling of this type of waste

could have a negative impact on the environment and human health due to potentially

hazardous substances that are generally associated with EEE. At the same time, your

cooperation in the correct disposal of this product will contribute to the effective usage of

natural resources. For more information on where you can drop off your waste equipment

for recycling, please contact your local city office, waste authority, approved WEEE scheme,

or your household waste disposal service.

*EEA: Norway, Iceland, and Liechtenstein

VIVIX-S 1012N User Manual

1.2.4 Trademarks

The name “Vieworks” and Vieworks logo are registered trademarks of Vieworks.

The copyright of this document is owned by Vieworks. Under copyright laws, this document cannot be

reproduced, in whole or in part, without the written permission of Vieworks.

Rev.1.0

Page 10 of 109 RA14-14B-011

1.3 Safety Instruction

This product is designed and manufactured to ensure maximum safety of operation and to meet all

the safety requirements applicable to electronic medical equipment. Follow these safeguards while

using the products. If not, severe personal injury or substantial property damage can be happened. It

is important for you to read and understand the contents of this manual before attempting to use the

product.

1.3.1 Management and Authority

 The product should be installed, operated, and serviced according to Vieworks

maintenance procedures and by personnel from Vieworks or distributor who providing

purchase of the Vieworks’ product.

 Operation and maintenance should be done in strict compliance with the operation

instructions contained in the manual.

 The system, in whole or in part, cannot be modified in any way without prior approval

from Vieworks.

 Before authorizing any person to operate the system, verify that the person has read and

fully understood the User Manual. The owner should make certain that only properly

trained and fully qualified personnel are authorized to operate the equipment. An

authorized operators list should be made and maintained.

 It is important that this User Manual be kept at hand, studied carefully, and reviewed

periodically by the authorized operators.

 If a malfunction occurs, do not use this device until qualified personnel corrects the

problem.

VIVIX-S 1012N User Manual

1.3.2 Power Supply

 Do not operate the equipment using any type of power supply other than the one

 Do not supply power to more than one piece of equipment using the same AC outlet for

 Do not connect a multiple portable socket-outlet or extension cord to the system. Doing

 Always connect the three-core power cord plug to a grounded AC power outlet.  Be sure to ground the equipment to an indoor grounded connector. Also, be sure to

 Do not use any power source other than the one provided with this product. Otherwise, a

 The owner should ensure continuous power supply to the system, with voltage and

 To make it easy to disconnect the plug at any time, avoid putting any obstacles near the

Rev.1.0

indicated on the rating label. Otherwise, it may result in a fire or electric shock.

this product. Doing so may result in a fire or electric shock.

so may result in a fire or electric shock.

connect all the grounds for the system to a common ground.

fire or electric shock may be caused due to a leakage.

current according to the product specifications. If the system is powered unstably during

its operation, we recommend you to install UPS (Uninterrupted Power Supply) to avoid

loss of data.

Page 11 of 109 RA14-14B-011

pull, bend, bundle, or step on them. Doing so may damage their sheath. If you alter them,

VIVIX-S 1012N User Manual

outlet. Otherwise, it may not be possible to disconnect the plug in an emergency.

 Do not place a heavy object such as medical equipment on cables and cords, and do not

it may damage the cords which could result in a fire or electric shock.

 Securely plug the power cord into the AC outlet. If contact failure occurs, or if dust/metal

objects come into contact with the exposed metal prongs of the plug, fire or electric

shock may result.

 Be sure to turn OFF the power to each piece of equipment before connecting or

disconnecting the cords. Otherwise, you may get an electric shock that could result in

death or serious injury.

 Be sure to hold the plug or connector to disconnect the cord. If you pull the cord, the

core wire may be damaged, resulting in a fire or electric shock.

 Do not handle the product with wet hands. You may experience an electric shock that

could result in death or serious injury.

1.3.3 Handling

 Never disassemble or modify the equipment. Doing so may result in a fire or electric

shock. Also, since the equipment incorporates parts that may cause an electric shock as

well as other hazardous parts, touching them may cause death or serious injury.

 Do not connect any equipment which is not specified in this User Manual.  Do not place anything on surface of the equipment. The object may fall and cause an

injury. Also, if metal objects such as needles or clips fall into the equipment, or if liquid is

spilled, it may result in a fire or electric shock.

 Do not hit or drop the equipment. The equipment may be damaged if it receives a strong

jolt. If the equipment is used without being repaired, it may result in a fire or electric

shock.

 Do not place excessive weight on the detector. The internal image sensor may be

damaged and it can affect to the image quality.

 Have the patient take a fixed posture and do not let him or her touch parts unnecessarily.

If the patient touches connectors or switches, it may result in electric shock or malfunction

of the equipment.

 Do not spill liquid or chemicals onto the detector. In cases where the patient is injured,

protect the equipment with a disposable covering not allow to come in contact with

blood or other body fluids. Otherwise, it may result in a fire or electric shock.

 For safety reasons, be sure to turn OFF the power of the equipment when the inspections

indicated in this manual are going to be performed.

 Do not submerge the detector in water.  Be sure to use the detector on a flat surface so it will not bend. Otherwise, the internal

image sensor may be damaged. Be sure to securely hold the detector while using it in

upright positions.

Rev.1.0

Page 12 of 109 RA14-14B-011

 Because the equipment cable is long, take care that cables do not become tangled during

use. Also, be careful not to get your feet caught in the cable. It may cause a malfunction

of the equipment or injury to the user from tripping over the cable.

 Do not block the ventilation ports of ViVIX SCU to prevent overheating. Overheating can

cause product’s malfunctions and damages.

1.3.4 Battery Pack and Charger

 Do not use the battery pack as a power source for equipment other than VIVIX-S 1012N

detector. Be sure to use only the dedicated battery pack for the VIVIX-S 1012N detector.

 The battery charger is designed for the dedicated battery pack. Do not use the battery

charger other than the dedicated one. Otherwise, a battery explosion or a battery leak

may occur, resulting in fire or electrical shock.

 Do not operate the battery charger using any type of power supply other than the one

indicated on the rating label.

 Do not handle the product with wet hands.  Do not attempt to disassemble, alter, or apply heat to the product.  Avoid dropping or subjecting the product to severe impacts. To avoid the risk of injury,

do not touch the internal parts of the battery if it has been cracked.

 Stop using the battery pack immediately if it emits smoke, a strange smell, or otherwise

behaves abnormally.

 Do not let the battery pack and battery charger come into contact with water or other

liquids and do not allow them to get wet.

 Do not clean with substances containing organic solvents such as alcohol, benzene,

thinner, or other chemicals. Otherwise, fire or electrical shock may result.

 Do not allow dirt or metal objects (such as hair pins, clips, staples or keys) to contact the

terminals. Otherwise, battery explosion or leakage of electrolyte may occur, resulting in

fire, injury or pollution of surrounding area. If the battery leaks and the electrolytes come

into contact with your eyes, mouth, skin or clothing, immediately wash it away with

running water and seek medical attention.

 Do not leave, store, or place the product in a location near heat sources, or in a place

subject to direct sunlight, high temperature, high humidity, excessive dust, or mechanical

shock. Otherwise, battery leakage, overheating or damage to the product may occur,

resulting in electrical shock, burns, injury or fire.

 Do not attempt to use a battery pack that has deteriorated. Using a battery pack that has

exceeded its life cycle may lead to overheating, fire or explosion.

 The Lithium ion battery is recyclable.  Battery slowly discharges even if not in use.  The battery pack may have expired if it discharges immediately after being fully charged.

You can purchase an optional battery pack to replace an exhausted one.

 The battery pack is a consumable item. If a fully charged battery is consumed quickly, use

a new and fully charged battery pack.

 Be sure to charge the battery periodically (once a year) if it is not used for an extended

Rev.1.0

VIVIX-S 1012N User Manual

Page 13 of 109 RA14-14B-011

period of time. The battery pack cannot be charged if it has been over discharged.

 Before discarding the battery pack, cover the terminals with adhesive tape or other

insulators. Contact with other metal materials may cause fire or explosion.

1.3.5 Environment of Use

 Do not install the equipment in any of the locations listed below. Doing so may result in

failure or malfuction, equipment falling, fire, or injury.

 Close to facilities where water is used.  Where it will be exposed to direct sunlight  Close to the air outlet of an air-conditioner or ventilation equipment  Nearby the electric heating applicance such as a heater  Where the power supply is unstable  In a dusty environment  In a saline or sulfurous environment  Where temperature or humidity is higher than the operating temperature  Where there is freezing or condensation  In areas prone to vibration  On an incline or in an unstable area

 This product may malfunction due to electromagnetic interference (EMI) caused by

telecommunication devices, transceivers, electronic devices, etc. To prevent the

electromagnetic wave from badly influencing the product, be sure to avoid placing it in

close proximity to the product. Or, change direction or position of the product or move

into the shielded place to reduce electromagnetic interference.

 This equipment is not suitable for use in the presence of a flammable anesthetic mixture

with air or with oxygen or nitrous oxide.

 Conductive fluids that drain into the active circuit components of the system may cause

short circuits that can result in electrical fire. Therefore, do not place fluids or food on any

part of the system.

 To avoid electric shocks and burns caused by use of the wrong type of fire extinguisher,

make sure that the fire extinguisher at the site has been approved for use on electrical

fires.

 The battery charger and ViVIX SCU (System Control Unit) cannot be used in patient’s

vicinity.

VIVIX-S 1012N User Manual

Rev.1.0

Page 14 of 109 RA14-14B-011

from the AC outlet, and contact sales representative or

1.3.6 Problem Management

 Should any of the following occur, immediately turn OFF the power to each piece of

equipment, unplug the power cord

distributor.

 When there is smoke, an odd smell or abnormal sound no period.  When liquid is spilled into the equipment or a metal object is entered through an

opening.

 When the equipment has been dropped and is damaged.

1.3.7 Maintenance and Inspection

 Do not use or store the equipment near flammable chemicals such as acetone, benzene,

thinner, etc. If chemicals are spilled or evaporated, it may result in a fire or electric shock

through contact with electric parts inside the equipment.

 If any flammable cleaning agent is used for the product, be sure to take care when using

them.

 When the equipment is going to be cleaned, be sure to turn OFF the power of the

equipment and unplug the power cord from the AC outlet. Never use thinner, acetone,

benzene or any other flammable cleaning agent. Otherwise, it may result in a fire or

electric shock.

 Clean the plug of the power cord periodically by unplugging it from the AC outlet and

removing dust or dirt from the plug, its periphery, and AC outlet with a dry cloth. If the

cord is kept plugged in for a long time in a dusty, humid or sooty place, dust around the

plug will attract moisture, and this could cause insulation failure that could result in a fire.

 Be sure to turn OFF the power of the equipment while cleaning. Otherwise, a fire or

electric shock may occur.

VIVIX-S 1012N User Manual

Rev.1.0

Page 15 of 109 RA14-14B-011

1.4 Product Usage Guide

 When using the equipment, take the following precautions. Otherwise, problems may

occur and the equipment may not function correctly.

1.4.1 Calibration



To ensure optimal system performance, it is important to verify that the system is calibrated correctly.



Check if the calibration is performed after the equipment is completed to be installed or repaired.



Do not try to use the system if the calibration has not been performed.



You can process calibration with the calibration data CD (provided).

 The calibration result can be different by the use environment. Therefore, if the result with

the provided calibration data is not satisfied, you can create the data at the field in

person by using VIVIX Setup, the calibration software.

VIVIX-S 1012N User Manual

1.4.2 Length Measurement



Before taking any length measurement on an image, carry out the length calibration with a reference

object and verify its results for correct measurement.

1.4.3 Left/Right Marker



The operator is responsible for making a correct and clear mark on the left or right side of the image.



The software includes a function to mark the image with L (left) or R (right) while acquiring the image

through printing and archiving.



Prepare an alternative way to prevent any confusion if the operator does not choose to use L/R marks.

1.4.4 Image Backup



To avoid missing images which might result in a patient being exposed to additional dose of radiation,

it is important to send images to PACS or backup images by using film or external storage media (CD,

DVD, HDD, USB).



If the hard disk of your workstation is about to be full, the operator should backup images to

somewhere else and delete them to make storage (memory) space in the hard disk for new patients.

 The image backup should be done as a routine operation for every patient and image.

Rev.1.0

Page 16 of 109 RA14-14B-011

1.4.5 Use Limitations



Vieworks software has the engineer mode operated by inputting the administrator password only.



This mode should be operated by the person who is qualified by Vieworks.

1.4.6 Disposal



Disposal of this product in an unlawful manner may have negative effects on human health and the

environment.



Be sure to follow the procedure which is in conformity with the laws and regulations applicable in your

area.

1.4.7 Pediatric Application



Every request should be reviewed by a pediatric radiologist prior to beginning the examination to

ensure that an appropriate study is being performed.



If the technologist notices an unusual request, he or she must contact a radiologist in charge.

Examples include orders- a Full Cervical, Thoracic, and Lumbar Spine series. The pediatric radiologist

should contact the ordering physician and decide which study is best for the pediatric patient.



The technologist should use a proper technique considering the patient’s size to decrease the

radiation dose when he or she acquires diagnostic images.



ALL pediatric patients shall be shielded for their X-ray examinations, except for when the shield will

obscure the region of interest, as in a pelvic or SI joint X-ray for trauma or arthritis, or when it is

physically or clinically unreasonable to shield the patient.



For routine Hip X-Rays, ALL male children shall have their scrotum shielded using the small gonadal

shield while females may not be shielded because doing so would obscure the hips.



To minimize motion in infants and young children, swaddle the infant. Use distraction tools to improve

cooperation and projectors with child-friendly themes, music, toys with flashing lights or music, child-

friendly images on the ceiling or walls, singing, counting, and a parent reading and talking to the child

through the console all can help reduce anxiety and comfort the child.



A scoliosis series will consist of a single frontal standing view of the spine. No lateral view or supine

view is needed, unless specifically asked for by the Orthopedist or Radiologist. If the female’s breasts

can be shielded without obscuring the spine, breast shields should be used.

VIVIX-S 1012N User Manual

1.4.8 Before Exposure



Be sure to check the equipment daily and confirm that it works properly.



Sudden heating of the room in cold areas will cause condensation to form on the equipment. In this

case, wait until the condensation evaporates before performing an exposure. If the equipment is used

while condensation is formed in it, problems may occur in the quality of captured images.



When an air-conditioner is used, be sure to raise/lower the temperature gradually so that difference

between the temperature in the room and in the equipment does not occur, to prevent condensation.

Rev.1.0

Page 17 of 109 RA14-14B-011

1.4.9 During Exposure



This equipment is not protected (sealed) against liquids such as blood and medicine in the operating

room. If necessary, wrap the equipment in a disposable cover when using it.



Do not use the selected frequency channel (2.4 ㎓ and 5 ㎓ dual band) for other wireless devices.

Mutual interference may affect the image data transmission rate.



Do not use the detector near devices generating a strong magnetic field. Doing so may produce

image noise or artifacts.

1.4.10 Operating and Storage Environment



This equipment is mainly used in the X-ray exposure room and hospital wards. To use it in other

places, consult Vieworks’ sales representative or a distributor.



Do not expose this equipment to high temperatures and/or high humidity. Malfunctions may occur.



When not in use, keep the products in a safe location.



Be sure to use and store this equipment under the conditions described below.

VIVIX-S 1012N User Manual

Classification Temperature Humidity (Non-condensing) Atmosphere

Operating Environment +10 ~ +35℃ 30 ~ 85% 700 ∼ 1060 hPa Storage Environment -15 ~ +55℃ 10 ~ 90% 500 ∼ 1060 hPa

1.4.11 Others



Do not use this equipment in combination with peripherals such as defibrillators or large electric

motors as these may cause power-supply noise or power supply voltage variations. Doing so may

prevent normal operation of this equipment and peripherals.

Rev.1.0

Page 18 of 109 RA14-14B-011

VIVIX-S 1012N User Manual

2. Product

This section gives an instruction about the product components and specifications.

Overview

Product Components

VIVIX-S 1012N Detector

VIVIX SCU

Battery Pack

Battery Charger

Others

Rev.1.0

Page 19 of 109 RA14-14B-011

2.1 Overview

ViVIX-S 1012N detector is the digital X-ray imaging solution. It acquires images by exposing X-ray which

has been penetrated the human body. When X-ray photons pass through scintillator in the detector, the

photons convert to visible ray, and the visible ray is converted to electronic signals through TFT (a-Si). Then

the detector digitalizes x-ray images and transfers them to the computer (workstation) for radiography

diagnostics. Users can perform image diagnosis easily through the image display monitor with this process.

Advanced digital image processing also allows considerably efficient diagnosis, all kinds of information

management, and sharing of image information on network.

VIVIX-S 1012N User Manual

 This detector is used for the general-purpose diagnostic procedures, and it is intended to

replace radiographic film / screen systems.

 This detector is not intended for mammography applications.

2.1.1 Features [TBD]



Since VIVIX-S 1012N detector is compatible with a conventional film cassette, it enables to replace

the analog radiographic diagnosis (Supporting ISO4090 standard).



The new sensor with 124μm pixel pitch produces high spatial resolution (approx. 5.2 Mega pixels)

digital images.



Various applications such as neonatal, ENT, equine and cephalo



Choose between two scintillator types (CsI and Gadox) of detector provided by Vieworks.



The built-in wireless communication supports IEEE 802.11n to acquire images without a wired

connection in anytime, anywhere.



Make direct wireless communication with the built-in wireless AP function. (Inside AP



Supports the stable and reliable AED (Auto Exposure Detection) function. (AnytimeTM)



Designed as lightweight and thin with portability to allow easy exposure in anytime, anywhere.



Used in various ways for infant / animals and in the dental clinic / ENT, etc.

)

Rev.1.0

Page 20 of 109 RA14-14B-011

2.2 Product Components

2.2.1 Detector

Component Description

VIVIX-S 1012N User Manual

VIVIX-S 1012N

Detector

Calibration DATA (CD)

 A deco sheet attached on the detector can be different depending on each client

company.

2.2.2 VIVIX SCU (VIVIX System Control Unit)

Component Description

[TBD]

 FXRD-1012NAW (2.2kg)  FXRD-1012NBW (2.1kg)

 Offset Calibration Data  Gain Calibration Data  Defect Map Data

 FXRS-03A (2.5kg)  FXRS-03B (2.8kg)

Rev.1.0

VIVIX SCU Basic

VIVIX SCU mini

 AC Power Cable (2m)

 FXRS-04A (1.2kg)

 You can choose either VIVIX SCU Basic or VIVIX SCU mini depending on the purpose of

use.

Page 21 of 109 RA14-14B-011

2.2.3 Battery & Charger

Component Description

VIVIX-S 1012N User Manual

VIVIX Battery

VIVIX Charger

2.2.4 Data

Component Description

Calibration Data

[TBD]

 FXRB-03A (0.12kg, 2EA)

 FXRC-02A (0.8kg)

 DC 24V

 Pre-offset data  Post-offset data  Gain data  Defect map data

Resource

2.2.5 Other Accessories

Component Description

Cables

 Software (Viewer or SDK)  Manuals

 Tether Interface Cable (7m)

 Ether Con Cable (7m, Option)

 Generator Interface Cable (7m)

 UTP LAN Cable (15m, Direct)

 CAT 5E or CAT6

Rev.1.0

Page 22 of 109 RA14-14B-011

VIVIX-S 1012N User Manual

 The use of accessories and cables other than those approved and sold by Vieworks Co.,

Ltd. may result in increased release of electromagnetic waves or decreased stability of the

equipment.

 Accessory equipment connected to the analog and digital interfaces must be certified

according to the respective IEC standards. All combinations of equipment must be in

compliance with IEC 60601-1-1 system requirements.

 Any person who connects additional equipment to the signal input or signal output ports

configures a medical system, and is therefore responsible for ensuring that the system

complies with the requirements of the system standard IEC 60601-1.

 Consult your sales distributor or manufacturer if you have any concerns.

Rev.1.0

Page 23 of 109 RA14-14B-011

2.3 VIVIX-S 1012N Detector

VIVIX-S 1012N is designed to acquire digital images by collecting x-ray signals and sereval conversion

processes. You can use the acquired image (10” x 12” film size) diversely depending on the purpose of use.

 VIVIX-S 1012N is one of the detector models produced by Vieworks.

2.3.1 Specifications

Item Specifications

VIVIX-S 1012N User Manual

Model

Image Sensor

X-ray Scintillator Type

Pixel Pitch  0.124㎜ (124㎛) Field of View  10” x 12” Active Area (H x V)  253.95㎜ × 317.44㎜ Active Array  2048 x 2560 pixels Effective Area  253.0㎜ x 316.4㎜ Effective Array  2040 x 2552 Grayscale  16bit Spatial Resolution  Min. 4.0 lp/㎜ Image Acquisition Time (Wired)  1 sec. Image Acquisition Time (Wireless)  3 sec. Recommended Cycle Time  15 sec.

X-ray Synchronization Control

 FXRD-1012NAW (CsI, wireless)  FXRD-1012NBW (Gadox, wireless)  a-Si (Amorphous Silicon) TFT  Fill Factor : 60%  FXRD-1012NAW : Csl: TI (Thallium doped Caesuim Iodide)  FXRD-1012NBW : Gd2O2S:Tb (Gadolinium oxysulfide)

 AED (Auto Exposure Detection)  DR Trigger (External line trigger)

Rev.1.0

 DC +24 V, Max. 0.7 A

Rated Power Supply

Power Consumption  Max. 17 W Dimensions (H × W × D)  287.0㎜ × 350.0㎜ × 15.2㎜ Weight (including a battery pack)  FXRD-1012NAW : 2.2 kg  FXRD-1012NBW : 2.1 kg

Image Transfer

Data Transmission Rate (Wired)  Max. 1Gbps Data Transmission Rate (Wireless)  Max. 300Mbps (MIMO 2X2)

 Wired: Powered by VIVIX SCU with a tether interface cable.  Wireless: Powered by a battery pack (3,100 ㎃ h)

 Wired: Gigabit Ethernet (1000BASE-T) via PoE (Power over

Ethernet)

 Wireless: IEEE802.11n

Page 24 of 109 RA14-14B-011

2.3.2 Drawing Sheet

VIVIX-S 1012N User Manual

Item Description

Dimensions (H × W × D) 287.0㎜ × 350.0㎜ × 15.0㎜

Curvature of Edges R6.5

 Under the ISO4090 regulation, the allowed tolerance of a thickness of detector is from -

2㎜ ~ +1㎜.

Rev.1.0

Page 25 of 109 RA14-14B-011

ether interface connector

Tether interface holder

Antenna for wireless LAN

VIX

Used for tighten the tether interface cable.

detector and

Fix/release holder of the tether interface cable.

battery pack.

Antennas for wireless communication (2EA)

Indicates communication and transmission

Indicates ready to work

Indicates power On/Off status

VIX

2.3.3 Functions

-S 1012N User Manual

Name

A T

C Battery lock lever

E Status indicator

F Power button

G AP ON /OFF Button



Description

  Used for wired connection between a

 Lock/unlock lever of the equipped

 Detector status indicator

 DATA LED (Blue):  ACTIVE LED (Orange):

 POWER LED (Green):  Detector power button 

VIVIX SCU.

Rev.1.0

Page 26 of 109

RA14-14B-011

2.3.4 Deco Sheet

Indication Info. Description

VIVIX-S 1012N User Manual

A Wireless communication logo

B Status indication logo

C Indicating image starting point

D Indicating center of the detector

E Vieworks logo

F Certification logo

 Image starting point (0.0) of this detector is located nearby the tether interface connector.

You can change the displayed direction of an image from the VIVIX Setup program, but

it does not mean that the starting point and direction of the original image are changed.

2.3.5 Wireless Communication

Item Specifications

Wireless standard IEEE802.11n

2.412 ~ 2.472㎓ (13 Channels)

Frequency range

5.18 ~ 5.24㎓ (4 Channels)

5.745 ~ 5.805㎓ (4 Channels)

Data transmission rate 802.11n: Max. 300Mbps (MIMO 2X2)

Modulation BPSK, QPSK, 16-QAM, 64-QAM

Transmission power Max. 17dBm

Security WPA2-PSK

Antenna Dual Band Antennas (2EA, inbuilt)

 The specification of detector and SCU are same, but their location of antennas is different.

Rev.1.0

Page 27 of 109 RA14-14B-011

2.3.6 Use Environment

Item Operation Storage & Transportation

Temperature +10 ~ +35℃ -15 ~ +55℃

Humidity 30 ~ 85% (Non-condensing) 10 ~ 90% (Non-condensing)

Atmospheric pressure 700 ~ 1060 hPa 500 ~ 1060 hPa

Shock 1.6G 20G

Vibration 0.7G 0.7G

 The use environment of detector and VIVIX SCU is same.

Load Limit of Detector [TBD]

VIVIX-S 1012N User Manual

Uniform load Local load

Over the whole surface Center diameter 40mm

Max. ?? kg Max. ?? kg

 Do not let the paitent or object heavier than load limit be on the detector. Then, detector

can be damaged.

 Do not let the patient lie or get on the detector. Internal devices such as a sensor can be

seriously damaged even if his/her weight is within the load limit.

Rev.1.0

Page 28 of 109 RA14-14B-011

2.4 VIVIX SCU (VIVIX System Control Unit)

VIVIX SCU synchronizes the image and X-ray signal as locating among the detector, workstation and the X-

ray generator. You can use the SCU directly when the power supplies to SCU after connecting it under the

VIVIX-S 1012N system environment.

 VIVIX SCU is divided into VIVIX SCU Basic and VIVIX SCU mini depending on its size.

2.4.1 Specifications

VIVIX SCU Basic

Item Specifications

Model  FXRS-04B

VIVIX-S 1012N User Manual

Power supply

Cable connection port

Wireless communication  IEEE 802.11n (2.4 ㎓ / 5 ㎓) Dimension (H × W × D)  210.0 ㎜ × 300.0 ㎜ × 58.0 ㎜ Antenna  105 ㎜ (2EA, Dual band) Weight  2.8 ㎏

VIVIX SCU mini

Item Specifications

Model  FXRS-04A Power supply  Input: DC +24V 2A Max

Cable connection port

Wireless communication  IEEE 802.11n (2.4 ㎓ / 5 ㎓) Dimension (H × W × D)  210.0 ㎜ × 170.0 ㎜ × 45.0 ㎜

 Input: AC100 to 240V, 50/60㎐, Max. 200VA  Output: DC +24V 3.3A, 80W  Gigabit Ethernet port (3EA)  PoE (Power over Ethernet) Port (2EA)

 Gigabit Ethernet port (3EA)  PoE (Power over Ethernet) Port (1EA)

Antenna  109 ㎜ (2EA, Dual band) Weight  1.2㎏

Rev.1.0

Page 29 of 109 RA14-14B-011

2.4.2 Drawing Sheet

VIVIX SCU Basic

VIVIX-S 1012N User Manual

VIVIX SCU Mini

Rev.1.0

Page 30 of 109 RA14-14B-011

VIVIX SCU Basic

VIX

(Including Green LED Lamp)

between the detector and

VIVIX

ready to communicate

-S 1012N User Manual

2.4.3 Function –

Front Side

No. Name

1 Power switch

Description

Turn on/off the power of VIVIX SCU.

2 Fan

3 Antenna

4 Status LED

Expels the air inside of VIVIX SCU.

Assists communications

Indicates the operation and connection status of

 Blinking green: Booting  Green: Completed to boot up  Blue: The detector is connected and

VIVIX SCU.

SCU.

Rev.1.0

Page 31 of 109

RA14-14B-011

Detector power supply port

(Potential Equalization)

qualization between

can be detached without the use of a tool

VIX

SUB 15pin x 2 EA, Female)

ommunication between the workstation and

FXRD

when configuring multiple detectors

Port 5

and

is used to maintain potential

Rear Side

-S 1012N User Manual

No. Name

EXT_INF1

EXT_INF2

LAN port

(Port 1, 2, 3)

3 PoE status lamp

PoE port

(Port 4, 5)

Description

X-ray generator interface connector (D-

 EXT_INF1 : 1 ~ 15  EXT_INF2 : 16 ~ 30

Gigabit Ethernet port (1000BASE-T)

 Port 1: C  Port 2, 3: Communication between

VIVIX SCU

Indicats the status of PoE port (Port 4,

 Green: 1 Gbps  Orange: 100 Mbps

PoE (Power over Ethernet) port (1000BASE

 Communication between the detector  Supplies power to the detector.

Max. DC +24V/24W (2 ports)

 For FXRD-1717S detector only.

VIVIX SCU.

-1717S detector and

)

VIVIX SCU.

6 P.E

7 AC input port

 The P.E

Rev.1.0

Equipotential ground

T2AL250V fuse (2 EA)

 100 ~ 240V  50/60㎐  Supplies power to VIVIX SCU.

port of VIVIX SCU

VIVIX SCU and another grounded system

Page 32 of 109

Use the conductor that

RA14-14B-011

VIVIX SCU Mini

VIX

. (Including Green LED Lamp)

between the detector and

operation and connectio

communicate.

-S 1012N User Manual

2.4.4 Function –

Front Side

No. Name

Description

1 Power switch

2 Antenna

3 Status LED

Turn on/off the power of VIVIX SCU

Assists communications

Indicates status of VIVIX SCU

 Blinking green: Booting  Green: Completed to boot up  Blue: The detector is connected and ready to

VIVIX SCU.

Rev.1.0

Page 33 of 109

RA14-14B-011

VIX

SUB 15pin, Female)

ommunication between the workstation and

VIVIX

Rear Side

-S 1012N User Manual

No. Name

1 EXT_INF

LAN port

(Port 1, 2, 3)

3 PoE status lamp

4 PoE port

5 DC power input port

Description

X-ray generator interface connector (D-

Gigabit Ethernet port (1000BASE-T)

 Port 1: C  Port 2, 3: Communication between FXRD-1717S

when configuring multiple detectors.

Indicats the status of PoE port.

 Green: 1 Gbps  Orange: 100 Mbps

PoE (Power over Ethernet) port (1000BASE-T)

 Communication between the detector and  Supplies power to the detector.

DC +24V

 Supplies power to VIVIX SCU

VIVIX SCU.

detector and VIVIX SCU

SCU.

Rev.1.0

Page 34 of 109

RA14-14B-011

2.5 Battery Pack

2.5.1 Specifications

Item Specifications

Model FXRB-03A

Type Lithium Ion

Rated Power Supply Output: DC +7.6V

Capacity 3,100㎃h

Number of cell 2S1P (2 Series 1 Parallel)

Life Approx. 500 times (Fully charged/Discharged completely, 1cycle)

Dimension (H × W × D) 160.0 ㎜ × 61.8 ㎜ × 5.7 ㎜

Weight 114g

VIVIX-S 1012N User Manual

2.5.2 Drawing Sheet

Rev.1.0

Page 35 of 109 RA14-14B-011

2.6 Battery Charger

2.6.1 Specifications

Item Specifications

Model FXRC-02A

Simultaneous Charging 2 battery packs

Charging time 2 hours

Rated power supply DC +24V, 2A Max.

Dimension (H × W × D) 192.0 ㎜ × 101.0 ㎜ × 27.5 ㎜

Weight 0.8 ㎏

2.6.2 Drawing Sheet

VIVIX-S 1012N User Manual

Rev.1.0

No. Name Description

1 Lock button Fixes a battery while it is in charging.

2 Power input port

Supplies electric power by connecting a power adapter to the battery

charger.

Page 36 of 109 RA14-14B-011

2.7 Others [TBD]

2.7.1 X-ray Generator (Recommended Exposure Condition)

Item Recommended condition

X-ray energy range  40kVp ~ 150kVp Reliability (Lifetime Dose)  74Gy or higher (35 uGy x 365days x 24hrs x 60min. x 60sec. / 15sec.)

2.7.2 Recommended Specification of Workstation (PC)

Item Recommended specification

 VIVIX Setup

 Microsoft Windows 7 (32bit / 64bit)  Microsoft Windows 7 64bit SP1 (Professional Edition or higher)

Operating System

 Microsoft Windows Vista Service pack 1 or higher (32bit / 64bit)  Microsoft Windows 8 (32bit / 64bit) / 8.1 64bit SP1 (Professional

Edition or higher

 Microsoft Windows 8.2 (32bit / 64bit)

VIVIX-S 1012N User Manual

CPU  Intel Core i5 2600 or higher (or compatible CPU) Memory  4GB or higher Hard Disk  1TB or higher

 Gigabit (for detector only)  Intel® PRO 1000 Series (Gigabit LAN Card for network interface)

LAN Card (only for

detector communication)

Monitor  1024 x 768 or more CD-ROM  CD or DVD R/W

 Min.requiremetns

 Speed: 1Gbps or more  Jumbo Frames: 9K

 Receive Descriptors: 2K (1024 or higher)

2.7.3 Recommended Specification of Grid

Item Recommended specification

SID  100cm / 130cm / 150cm / 180cm Size  451mm x 365mm x 1.5mm Ratio  8.1 / 10:1 / 12:1

Rev.1.0

Frequency  215 line/inch INTER SPACER  AL

Page 37 of 109 RA14-14B-011

VIVIX-S 1012N User Manual

 Check the recommended specifications by Vieworks first before buying the generator,

workstation and grid.

Rev.1.0

Page 38 of 109 RA14-14B-011

VIVIX-S 1012N User Manual

3. System Configuration

This section gives information about the various connection / configuration ways among the

detector, VIVIX SCU, workstaton and X-ray generator.

You can figure out the most suitable way of system configuration through this instruction.

Detector Connection Methods

Diagram

System Configuration

Generator Interface

Rev.1.0

Page 39 of 109 RA14-14B-011

Methods

wired or wireless connection

connection

are transmitted between the

A battry pack should be installed in the detector to use it under the

We recommend

When using the unfixed detector.

When the wired

The wireless

Use the wireless connection with a laptop computer to

Be sure to operate the wireless commnunication

a maximum of

Use of multiple WLAN devices within the same frequency band may interfere

wireless communication and cause a decline in transmission speed

Do not cover or block the wireless module of the detector.

between the detector and

operable distance may be reduced

VIX

detector

ways suitable for the use environment in case of need.

detector and

wireless

for the

interruption

than the wired connection.

mobility.

between the detector a

Also, do not put any shielding

Otherwise, the transmission speed or

-S 1012N User Manual

3.1 Detector Connection

You can organize

can also choose other

between the VIVIX-S 1012N

and VIVIX SCU. You

3.1.1 Wireless Connection



The images and data

connection.







  



within



materials

VIVIX-S 1012N

you to use the wireless connection method

communication is in trouble by the

connection is more freely to operate

8m.

VIVIX SCU.

enhance

VIVIX SCU by wireless

configuration.

following cases.

of cables.

nd VIVIX SCU

with each

Rev.1.0

Page 40 of 109

RA14-14B-011

3.1.2 Wired Connection



Connect ViVIX-S 1012N detector and VIVIX SCU with a tether interface cable to make a wired

configuration.



As the tether interface cable supplies power to the detector, a battery pack is not needed to be

installed in the detector.

 We recommend you the wired connection method for the following cases.

 When continuous power supply to the detector is needed.

 When the detector is fixed in a bucky stand or on a table.

 When you upgrade the detector firmware or change the inner configural information.

 When you need the data communication to be faster than the wireless connection.  A battery pack in the detector keeps charging under the wired connection.  The wireless communication module of the detector maintains inactivation status.

VIVIX-S 1012N User Manual

Rev.1.0

Page 41 of 109 RA14-14B-011

3.2 Diagram

3.2.1 Block Diagram

VIVIX-S 1012N User Manual

3.2.2 Wiring Diagram

Rev.1.0

Page 42 of 109 RA14-14B-011

System Configuration

his section gives information about

generator.

AP Mode (SCU AP Mode)

connection

detector and

(Access Point) and

VIVIX SCU & PC (Workstation)

and PC (Workstation) are

available

detector operate as

generator can be connected with the generator interface cable.

It is unnecessary to connect

you use AED mode of the detector

VIX

detector,

with

In this case,

n this case,

-S 1012N User Manual

3.3

3.3.1

workstation and the

SCU AP mode is the wireless

center wirelessly.

the configuration modes of VIVIX-S 1012N

method that connecting the detector

VIVIX SCU,

VIVIX SCU as the

VIVIX SCU & Detector



The VIVIX-S 1012N

detector operate as AP



VIVIX SCU

 It is

VIVIX SCU & Generator



VIVIX SCU and the



cable if

VIVIX SCU are connected wirelessly.

STATION respectively.

connected with the LAN cable.

to connect VIVIX SCU and PC wirelessly. I

AP (Access Point) and STATION respectively

VIVIX SCU and the generator with

VIVIX SCU and the

generator interface

Rev.1.0

Page 43 of 109

RA14-14B-011

r interface mode is the wired

VIVIX

connection

VIX

connecting the detector

are connected with the tether interface cable

same

3.3.2 Tether Interface Mode

-S 1012N User Manual

Tethe

center.

VIVIX SCU & Detector

connection method that

with VIVIX SCU as the



VIVIX SCU and the

 Other

-S 1012N detector

ways of the tether interface mode are the

as the AP mode.

Rev.1.0

Page 44 of 109

RA14-14B-011

External AP mode is the wireless

VIVIX SCU

VIVIX

and the detector operate as

connection

Be sure to check the specifications of external AP device when configuring

AP mode, since the wireless communication performance can be different

specifications

VIX

method that adding the external AP device instead of

n this c

same

3.3.3 External AP Mode

-S 1012N User Manual

SCU.

connection

VIVIX

External AP & VIVIX SCU



The external AP and

External AP & Detector



The external AP and

 Other



are connected with a LAN cable.

-S 1012N detector are connected wirelessly. I

AP (Access Point) and STATION respectively.

ways of the tether interface mode are the

ase, the external AP

as the AP mode.

the external

by the

Rev.1.0

Page 45 of 109

RA14-14B-011

Detector AP mode is the wireless

wirelessly

Detector & PC (Workstation)

detector

(Access Point) and

VIVIX SCU

mode without a wired

This mode can be used when mobility and portability are needed.

When configuring

module installed in the PC. The wireless communication performance can be different

depending on the specifications of the wireless module.

If the wireless

can be

VIX

method that connecting the PC (Workstation)

n this case, the detector

is not used for configuring the detector AP mode, you

Trigger

e to check the specifications of wireless

cannot be made normally because of unexpected p

3.3.4 Detector AP Mode

-S 1012N User Manual

connection

detector as the center



The VIVIX-S 1012N

operate as AP

and PC are connected wirelessly. I

STATION respectively.

with the

and the PC

 Since

AED



VIVIX SCU

connection. (Cannot use the DR

the detector AP mode, be sur

connection

needed to check the detector condition.

can only use the

mode.)

roblems,

Rev.1.0

Page 46 of 109

RA14-14B-011

Alone Mode

Alone

take images with

(Cannot use the

d images are stored

be transmitted to

transmitted

VIX

mode without making a wired or wireless connection.

using the

the detector

the detector.

-S 1012N User Manual

3.3.5 Detector Stand-

You can use the Stand-

 You should

DR Trigger mode.)

 The acquire

images can

 The

images are removed automatically from

the AED mode only when

in the internal storage of

the PC after connecting

Stand-Alone mode.

in order and the

to the PC.

Rev.1.0

Page 47 of 109

RA14-14B-011

Generator Interface M

detector provides

The detector detects

acquisition

he detector and

VIVIX

interface cable.

AED (Auto Exposure Detection) Interface Mode

detector is used as

the detector with

Cautions when using AED interface mode

Make sure to follow

Do not give impact to the product.

without the X

You may not acquire images

environment such as exposure condition, thickness of object or

When you set X

detector should be in

VIX

as a generator interface wa

automatically and then performs

enerator receive and send their signal to each other for

enerator should be connected with

images without

(Temp:

If it receives strong jolt, unwanted images may be

may occur depending on

the use of

ay exposure area to the direction of the detector, the center of the

ray exposure area. Otherwise, you may not acquire

-S 1012N User Manual

3.4

3.4.1

VIVIX-S 1012N

images by detecting X-ray.

Mode Description

AED

DR Trigger

If the VIVIX-S 1012N

generator to

image

acquisition.

ode

DR Trigger mode and AED mode

X-ray exposure from the generator

without any cable connection.

SCU and X-ray g

the AED mode, you can acquire

a generator interface cable.

y to acquire

image

the generator

connecting the

 

acquired



an image.

the operating environmental condition

-ray exposure because of the malfunction

-r

volved in the X-

of the AED sensor.

or horizontal artifacts

+10℃ ~ +35℃).

the external

grid.

Rev.1.0

Page 48 of 109

RA14-14B-011

DR Trigger Interface Mode

ray generator with a generator interface cable, and then

signal

EXP_REQ

complete

ray generator confirms

image

is a sending signal from X

is an exposure ready signal from the detector to X

VIX

EXP_OK

detector for requesting

ray generator.

-S 1012N User Manual

3.4.2

Connect the detector and X-

sending and receiving their

Signal Processing Steps

1 The detector receives

2 After the detector

generator.

3 The X-

4 The detector acquires

signal from the X-ray generator.

s to prepare image acquisition, it sends the

EXP_OK signal and generates X-rays.

s and then transmits the image data.

acquire images by

signal to the X-ray

 EXP_REQ

exposure.

 EXP_OK

-ray generator to the

Rev.1.0

Page 49 of 109

RA14-14B-011

Configuring DR Trigger Interface Mode

interface

onnect the one end of generator interface cable to

then connect the other end to the g

generators can be connected

generator

The generator interface cable is

Description

andle

Handle

Multipe detectors

a generator

The generator tramsmits and

VIX

generator should be connected with

EXT_INF

ed differently depending on the Trigger interface ways.

signal.

the one selected

-S 1012N User Manual

3.5

To configure the DR Trigger

generator interface cable. C

and

 Up to three  Only one

3.5.1 Trigger Interface Way

Trigger Interface

Packet Trigger H

Line Trigger

mode, VIVIX SCU and the

enerator.

with VIVIX SCU Basic.

can be connected with VIVIX SCU mini.

connect

s exposure signal by exchanging packet.

s exposure signal by exchanging electrical

port of VIVIX SCU,

3.5.2 Packet Trigger

  Connect 

images.

Rev.1.0

share one generator signal together.

interface cable to one of the pin groups.

receives signal with

Page 50 of 109

detector for taking

RA14-14B-011

ach detector shares a signal

Up to three X

connection

ou should comprehend about a

he engineer who understand

charge of interface

VIX

generator

ed from

ray generator to make

location

generator device and interface technology should be in

3.5.3 Line Trigger

-S 1012N User Manual

 E   The

-ray generators can be connected to SCU.

of each detector and generator can be configur

signal by being connected with

s separately.

VIVIX Setup.

 Y

Otherwise, X

 T

ray can be exposed to the detector in different

detector and X-

the

correct exposure.

work between VIVIX SCU and the generator.

Rev.1.0

Page 51 of 109

RA14-14B-011

3.5.4 EXT_INF Port Pin Map

EXT_INF port is D-SUB 15 pin female connectors of VIVIX SCU, and used for the generator interface.

EXT_INF1 port pin map definition (1 ~ 15)

No. Signal name I/O Type Color Ch. Description

1 EXP_REQ+_A Input Contact Red A Receives EXP_REQ

VIVIX-S 1012N User Manual

2 EXP_REQ-_A Input Contact Black A Returns signal from EXP_REQ+_A

3 EXP_REQ_TTL_A Input TTL Orange A Receives EXP_REQ

4 EXP_REQ_GND_A Input TTL Gray A Returns signal from EXP_REQ_TTL_A

5 EXP_OK_POWER_A/B Input - Yellow A/B Power of TTL signal

6 EXP_OK+_A Output - Green A Sends EXP_OK

7 EXP_OK-_A Output - Brown A Returns signal from EXP_OK+_A

8 EXP_OK+_B Output - Blue B Sends EXP_OK

9 EXP_OK-_B Output - Pink B Returns signal from EXP_OK+_B

10 Reserved - - - - Reserved for test only.

11 EXP_REQ+_B Input Contact White B Receives EXP_REQ

12 EXP_REQ-_B Input Contact Purple B Returns signal from EXP_REQ+_B

13 EXP_REQ_TTL_B Input TTL White/Red B Receives EXP_REQ

14 EXP_REQ_GND_B Input TTL White/Black B Returns signal from EXP_REQ_TTL_B

15 Reserved - - - - Reserved for test only.

EXT_INF2 port pin map definition (16 ~ 30)

No. Signal name I/O Type Color Ch. Description

16 EXP_REQ+_C Input Contact Red C Receives EXP_REQ

17 EXP_REQ-_C Input Contact Black C Returns signal from EXP_REQ+_C

18 EXP_REQ_TTL_C Input TTL Orange C Receives EXP_REQ

19 EXP_REQ_GND_C Input TTL Gray C Returns signal from EXP_REQ_TTL_C

20 EXP_OK_POWER_C Input - Yellow C Power of TTL signal

21 EXP_OK+_C Output - Green C Sends EXP_OK signal

22 EXP_OK-_C Output - Brown C Returns signal from EXP_OK+_C

23 EXT_W+ Input Contact - - User-defined Pin 1

Rev.1.0

Page 52 of 109 RA14-14B-011

VIVIX-S 1012N User Manual

24 EXT_W- Input Contact - - Returns signal from EXT_W+

25 EXT_X+ Input Contact - - User-defined Pin 2

26 EXT_X- Input Contact - - Returns signal from EXT_X+

27 EXT_Y+ Input Contact - - User-defined Pin 3

28 EXT_Y- Input Contact - - Returns signal from EXT_Y

29 EXT_Z+ Input Contact - - User-defined Pin 4

30 EXT_Z- Input Contact - - Returns signal from EXT_Z+

 Since VIVIX SCU mini has EXT_INF 1 port, only one generator can be connected with.

 Up to three X-ray generators can be connected to EXT_INF1 and EXT_INF2 ports, and

each generator should be connected with a same channel.

 There are Contact type (OPEN/ CLOSE) and TTL type (ON/ OFF) on the signal in/output

pin.

 TTL type information

 ON : VCC

 OFF : GND

 Current: 5 ㎃ ~ 10 ㎃

 Voltage: 12 V ~ 24 V

 When you plan to add interface using a user-defined pin, contact to the person in charge

of Vieworks.

Rev.1.0

Page 53 of 109 RA14-14B-011

3.5.5 Input / Output Circuit

Exposure Request Input Circuit (EXP_REQ)

VIVIX-S 1012N User Manual

Exposure Respond Output Circuit (EXP_OK)

Rev.1.0

Page 54 of 109 RA14-14B-011

VIVIX-S 1012N User Manual

4. Installation [TBD]

This section gives information about the installation process and method to use a detector.

Battery Pack

Product Installation

Generator Connection

Software Installation

Windows Environment Setting

Rev.1.0

Page 55 of 109 RA14-14B-011

[TBD]

and its attached devices should be

If you encounter any problems, consult

How to insert a battery pack

battery into a slot until it clicks and push the

Check if the

Make sure that the battery pack is securely

The remaining battery can be checked from

VIVIX

VIX

n authorized

in Vieworks

fixing the battery

lamp on the side of detector

-S 1012N User Manual

4.1 Battery Pack

 Detector 

4.1.1

engineer.

installed by a

the sales representative

service engineer.

or a relevant

1 Open the battery cover.

2 Insert a

3 Close the battery cover.

  

from the

lever to the right for

battery is fully charged before using.

inserted.

the battery

Setup program.

Rev.1.0

Page 56 of 109

RA14-14B-011

a battery pack

Push the lever to the left for taking out the battery.

Make sure to turn off the detector by pressing and hold the power button for 3 seconds

before detaching a battery pack

VIX

lamps are off and then

-S 1012N User Manual

4.1.2 How to take out

1 Open the battery cover.

3 Close the battery cover.



turned off.

Rev.1.0

Page 57 of 109

. All status LED

the detector is

RA14-14B-011

How to charge a battery pack

operated when it is connected wirelessly. C

with the power adapter before charging a battery

turned to green, it means that the power is permitted

Open the cover at the lower side of charger.

Put the battery on the top of charger in

Push the battery down until it is fixed in

ose the cover at the lower side of charger.

VIX

harge the battery pack fully

When the power LED is

-S 1012N User Manual

4.1.3

The detector is battery-

inserting it to the detector.

Charging type 1

Supply power to the charger

before

Rev.1.0

4 Cl

Battery charger

Tether interface cable

the right direction.

the charging part.

Stimultaneous charging Charging time

2 battery packs ? hrs

1 battery pack ? hrs

Page 58 of 109

RA14-14B-011

with the power adapter before charging a battery

turned to green, it means that the power is permitted

Open the cover at the lower side of charger.

Insert the battery into the slot until it clicks.

Close the cover at the lower side of charger.

The charging time can be

While charging a battery pack, i

tether interface cable

detector is designed to make

off

some time. Otherwise, over discharge may occur resulting in the shortened b

Do not use the charger around the paitent

harge the batter

Securely plug the power cord

or if dust/metal objects come into contact with the exposed metal prongs of the plug, fire

or electric shock may result

Stop charging the battery when status LED of the charger turns to green as exceeding th

specified charging time. Otherwise, the

If the battery pack is overheating, it can be exploded and a fire may occur.

a power adapter

VIX

When the power LED is

epending on temperature and

t is available to use the detector by connecting it with a

battery being discharged little by little

the detector is not

into the AC outlet. If contact failure occurs,

y pack is overcharged and it causes smoke.

1 or IEC 60950

Charging type 2

-S 1012N User Manual

Supply power to the charger



different d

charging status of a

battery.



 This

detector is

. Therefore, remove the battery pack when

during the

used for

attery life.

  C 

y with the charger provided by Vieworks.

of the charger



batter

 Use only

complying with IEC 60601-

-1.

Rev.1.0

Page 59 of 109

RA14-14B-011

Installation of this equipment should be made by licensed and authorized personnel

This equipment must only be connected to the power with protective earth

DR Trigger

of SCU, and the other to the X

If you use the AED mode, a generator interface cable is not needed as the detector

operates by detecting X

LAN

Connector of workstation assigned for

antenna of SCU upright

To transmit image data using a Tether Interface, connect the one end of the Tether

the Port 4 or Port 5 of SCU and the other to the detecto

If you use the wireless communication method, a tether interface cable is not needed as

image is transmitted wirelessly.

To supply power, connect the

VIX

onnect the one end of generator interface cable to the

of SCU, and the other to the LAN Card

port of SCU

4.2 Product Installation

4.2.1 Connecting Devices

-S 1012N User Manual

SCU Basic



Vieworks.



Rev.1.0

1 If you use the



2 Connect one end of the

3 Stand the



the

mode, c

-ray generator.

-ray automatically.

cable to one of the LAN ports

data transfer.

AC power cable to the AC power input

Page 60 of 109

EXT_INF port

Interface cable to

RA14-14B-011

Vieworks FXRD-1012NAW User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual