Vibe DSX11, XG8 Setup Information Manual

RADIO SETUP INFORMATION

CHOICE

☆ Transmitter Setup For The JR DSX11

JR-CCPM plays a critical role in coordinating the simultaneous activating of multiple servos to control
the swashplate. Activation of just a single servo would not lead to control of the swashplate - the three
swashplate servos must be controlled in a coordinated fashion. The setup of these servos di󱐯ers from that for
other control functions which control just one servo (for example, the Rudder).
The initial settings given here must be conrmed on the bench, and then ne tuned after test ying the
helicopter. Prior to commencing this process, conrm all the trim levers and trim knobs on the transmitter are in
their neutral (zero) positions. Also shift all switches to position”0” (switches moved away from the operator).

Please also be familiar with the instructions for the transmitter. The initial settings can be entered into the
transmitter without turning power on to the receiver. Please note that ne adjustment will be needed after test
ying the helicopter.

1. Initial Radio Setup

① Press (and hold) the 【ENT】key located on the

lower left of the Transmitter, then turn on the power
switch.

(「SYSTEM LIST」, List screen displayed)

② Turn the dial on the right side of the Transmitter to

select 「MODEL SELECT」 and press the dial.

* If your radio is new or if you are selecting a model

number which has no data in it, No.11 display will
be shown automatically.

③ Turn the dial to select 「YES」 and press the dial.

⑭

③,⑦
⑩,⑯

⑨

①【ENT】+【ON】

② Select「Model SELECT」

③ Select「YES」

② , ④〜⑥
⑧ , ⑩〜⑬ , ⑮

④ Turn the dial to select the model number you wish

to resete and press the dial again to select it.

⑤ Turn the dial to select the【LIST】key to return to

「SYSTEM LIST」 .

⑥ Turn the dial to select 「COPY/ERASE」 and press

the dial.

⑦ Press the 【CLR】Key to select YES.

④ Select the model to be
reset.

⑤ Select「LST」

⑥ Select「COPY/ERASE」

P.2

⑦ Select「YES」

⑧ Conrm the model No. you selected is shown and

select 「ERASE」 and press the dial.

⑧ Select「ERASE」

⑨ Press the 【FUNCTION】Key to select ERASE.

⑩ Press 【CLR】 to select YES and reset the model.

⑪ Select 「HELI」 and press the dial key, then input

the 「MODEL NAME」. After you input the model
name, press the 【LIST】 key 「OK」. also then press
the 【ENT】 key 「OK」.

⑨ Select「ERASE」

⑩ Select「YES」

⑪ Select「HELI」

⑫ Turn the dial to select 「3 Servo 120 ゜」 or 「3 Servo

140 ゜」 and press it.

(this choice depends on the hardware configuration

of your model)

⑬ Input the numbers, +/-, and REVERSE direction of

each servo as shown in the gure.

w/Flybar Head FLB Head

⑭ Press the 【ENT】Key.

⑮ If your helicopter uses the Flybar, select 「AUX2」

and if your helicopter is FBL, select 「GEAR」.

⑫ Select either 120° or 140°

⑬ Input these parameters⑬ Input these parameters

⑯ Press the【ENT】key to return to the regular

screen.

⑮ Select 「AUX2」 for Flybar head and select 「GEAR」 for FBL head.

P.3

2. Setting Rudder Servo Direction (REVERSE SWITCHES)

① Switch over to 「FUNCTION LIST」 by pressing the

【ENT】 key, turn the dial and select 「REVERSE SW」

then press the dial again.

② Turn the dial to 「RUDD」and reverse as necessary.
　Return to 「FUNCTION LIST」 by pressing the【LST】

key.

3. Setting TRAVEL ADJ. Values

① Turn the dial to select「TRVL ADJ.」and press the

dial.

①

②,③

① Select「REVERSE SW」

※ Note: The rudder reverse switch direction will depend
on the servo and gyro/FBL unit used. Please refer to
your gyro/FBL unit instruction manual for further details.

①,④

② Turn the dial to select each item and press the dial

to change each in turn.

③ Turn the dial to shift to each item and input the

number as shown in the gure.

※「U se the appr opria te con trol stick to sw itch

between H/L, U/D or L/R.

④ Press the【ENT】key to return to regular screen.

① Select「TRAVEL ADJ.」

②,③

③ Input the number

② Select item

※ Note that the 「THRO」 direction and travel adjust
settings will depend on the ESC used.

Setting for other models of Radio set.

※ 1 If you use a transmitter other than the JR DSX11 (or the XG8 described below), please refer to the

manufactures instruction manual, in combination with the helicopter assembly manual.

※ 2 Please refer to your tail gyro instruction manual for advise on tail rotor setup and initial transmitter

settings.

※ 3 If you are using a FBL system other than the TAGS01, please refer to your FBL system manual.

P.4