150 PSI ILLUMINATED
DASH PANEL GAUGE KIT
PART NO. 10061 (For Use with 20/30 Amp Systems)
PART NO. 20062 (For Use with 30/40 Amp Systems)
IMPORTANT:
It is essential that you and any other operator of this
product read and understand the contents of this manual
before installing and using this product.
SAVE THIS MANUAL FOR FUTURE REFERENCE
USER MANUAL
150 PSI Illuminated Dash Panel Gauge Kit
Please read this instruction manual carefully prior to operating this product.
Pay particular attention to the CAUTION and WARNING statements in this manual.
Failure to comply with these instructions could result in personal injury or property
damage. Retain these instructions for future reference.
PARTS LIST:
0
2
5
2
5
1
1
0
1
0
3
2
3
5
5
0
0
H1 H2
B C D E FA
I
J L
K M
G
N
A. Illuminated Dash Panel Gauge with On/Off Switch (1pc)
B. Mounting Bolts (2pcs)
C. Locking Washer (2pcs)
D. Nuts (2pcs)
E. 20 Ft. Extension Lead Wire with Inline Fuse / Fuse Holder (1pc)
F. 1/8” (F) NPT Compression Fitting for 1/4” O.D. Air Line (1pc)
G. Ring Terminals (3pcs)
H1. Insulated Female Terminal Connectors (2pcs)
H2. Insulated Female Terminal Connector (1pc)
I. Insulated Male Terminal Connectors (2pcs)
J. Quick Splice Connectors (2pcs)
K. Cable Tie Brackets (3pcs)
L. Cable Ties (6pcs)
M. Continuous Grommet (1pc)
N. Fuse (2pcs)*
*20 Amp Fuse & 30 Amp Fuse (P/N: 10061) or 30 Amp Fuse & 40 Amp Fuse (P/N: 20062)
INSTALLATION INSTRUCTIONS:
CHECK FOR CORRECT GAUGE KIT: The Illuminated Dash Panel Gauge Kit (P/N 10061) was
designed for Onboard Air Installation with our 90-100 Series Air Compressors. The Illuminated Dash
Panel Gauge Kit (P/N 20062) was designed for Onboard Air Installation with our 200-400 Series Air
Compressors. Please make sure that you have the correct Gauge Kit.
For installation to compressors/systems other than VIAIR components, please nd out the
Maximum Amp Draw of your compressor and refer to the following chart:
Compressor Max. Amp Draw
20 Amp
30 Amp
VIAIR Illuminated Dash Panel Gauge Kit
P/N 10061
P/N 20062
IMPORTANT: The Illuminated Dash Panel Gauge has been fully function tested and calibrated for
accuracy. The air inlet on this gauge has a factory installed compression tting. DO NOT ATTEMPT
to tighten or loosen the body of this compression tting. Any adjustments will likely cause the gauge
to malfunction and void warranty. (See Fig. 3)
NOTE: The Illuminated Dash Panel Gauge included in this kit is rated for 150 PSI. DO NOT
pressurize gauge to more than 150 PSI. Over-pressurization will cause the gauge to malfunction
and void warranty.
USER MANUAL
150 PSI Illuminated Dash Panel Gauge Kit
STEP BY STEP INSTALLATION:
1. Select mounting location with a rigid mounting surface such as the bottom edge of the
dashboard on either side of the steering wheel column. Use the gauge mounting panel as a
template to mark off two mounting points to be drilled. Drill two 13/64” diameter
holes as marked. Do not mount Gauge at this time.
NOTE: If you have existing 1/4” O.D. air line tubing routed, cut off a 1/2” to 1” section of air line
tubing from the tip of your existing air line before connecting the air line to the gauge as to
ensure that you have a fresh air line tip for connection.
2. If you do not have a pre-existing 1/4” O.D. air line, measure the length of the air line
required to route from Gauge to Air Source. Use a length of 1/4” O.D. air line that is at least the
length you just measured. Do not cut your air line at this time. Remove only the collar of the
compression tting from the back of the Dash Panel Gauge. DO NOT loosen or tighten the
bodyofthecompressionttingwhichispermanentlyafxedtotheairinletofthegauge.
Insert the 1/4” O.D. air line through the compression tting collar, then push air line onto the
barb of the compression tting until the air line completely covers the barb. Tighten collar to
the body of the compression tting with wrench. (See Fig. 1)
NOTE: When cutting air line, cut as squarely as possible. Use a hose cutter or razor blade. To
ease insertion of air line tubing into ttings, lightly lubricate the tip of the air line or soak air line
in warm water for about 5 minutes to soften the air line. When routing air line, always remember
to avoid sharp edges, heat source, and tight bends. Air line must be routed at least 12” away
from exhaust systems.
3. Temporarily place Dash Panel Gauge at mounting location and route the air line tubing on
the Dash Panel Gauge to your air source. (In a typical setup, your air source will be the air tank).
Measure and cut air line to appropriate length, connect air line to air source using the provided
1/8” (F) NPT compression tting. (See Fig. 3 & 4)
NOTE: In some cases, a hole may be required to be drilled in the rewall to enable the air line
and/or wire to pass through the rewall to air and power sources. Make sure that the air line
tubing and wire is protected from sharp edges of the drilled hole.
A continuous grommet strip is included in your kit. Seat grommet strip around the edge of the
hole, measure and cut strip to appropriate length. Work the strip around the hole opening until
the slot in the grommet strip sits rmly all the way around the edge of the hole. It will be
necessary to seal any grommets or holes that have been cut or drilled so as to seal off the
elements from entering the cab area of your vehicle. Use cable ties, air line clips, and/or cable
tie brackets to secure air line and/or wire to the vehicle.
IMPORTANT: Drilling through the rewall, always make sure what is on the other
side of the rewall before drilling. Make sure not to damage your vehicle’s electronic
systems/components when drilling.
4. The Illuminated Dash Panel Gauge comes with a built-in On/Off Switch, which is to be
connected to your pressure switch via the provided 20 Ft. lead wire. (See Fig. 3 & 4)
Your pressure switch should be connected to your relay and Dash Panel Gauge On/Off switch.
There are three insulated female terminal connectors included in your kit. If your pressure
switch has spade type push on connectors, attach the larger female terminal connector to one
end of the provided 20 Ft. extension lead wire (the end without the inline fuse). To connect 20
Ft. extension lead wire to your pressure switch, simply push female terminal connector onto the
spade connector on your pressure switch. If your pressure switch has lead wires instead of
spade type connectors, simply attach provided insulated male terminal connector to your
pressure switch lead wire. Connect 20 Ft. extension lead wire by pushing the female terminal
connector onto the male terminal connector. (See Fig. 3 & 4)
USER MANUAL
150 PSI Illuminated Dash Panel Gauge Kit
5. Route 20 Ft. extension lead wire from pressure switch to the Dash Panel Gauge. Measure and
cut lead wire to appropriate length. Do not discard the remaining length of the wire which has
the inline fuse. This remaining length of wire with the inline fuse is called the power wire.
6. Place Dash Panel Gauge under dash over the two holes that were drilled by using the provided
screws, nuts, and washers provided (mount the Dash Panel Gauge to the dash).
7. Attach one of the two smaller female terminal connectors to the extension lead wire that
was routed from the pressure switch. There are two male spade connectors on the back of the
On/Off switch. Connect the female terminal connector on the extension lead wire to the male
spade connectors on the On/Off switch. (See Fig. 4) Next, attach an appropriate size ring
terminal provided to the end of the power wire with the inline fuse. This means the ring
terminal will now be about 12” from the inline fuse. Temporarily position the ring terminal at
the power source and route power wire from the power source to the Dash Panel Gauge,
measure and cut power wire to appropriate length. Remove power wire from power source.
Next, attach the remaining smaller female terminal connector to the end of the power wire and
connect to the remaining male spade connector on the On/Off switch. (See Fig. 4)
NOTE: Do not connect gauge to power source at this time.
8. There are two wires, one red and one black connected to the light bulb of the gauge. Connect
the red wire to a sustainable fused dash panel circuit. Use the quick splice connector provided
for wire connection. (See Fig. 2) for how to use the quick splice connector. The black wire is
to be connected to a suitable ground source. Use the ring terminal or the quick splice
connector for ground wire connection.
NOTE: Consult vehicle manufacturer’s electrical diagram.
To use the quick splice connector, simply insert wire into one hole of the splice connector and
slip the connecting wire into the other hole. Once the wires are properly placed, close the top
of the quick splice connector. The connector will pierce wire insulation to complete wire
connection. (See Fig. 2)
9. Before connecting the power wire to power source, check to make sure that the On/Off switch
on the Dash Panel Gauge is in the Off position. Connect the ring terminal of the power wire to
power source.
10. Your illuminated Dash Panel Gauge installation is now completed. Run your compressor a
short time to build up pressure in air tank. Inspect all air line connections for leaks with soap
and water solution. If a leak is detected, the air line may not be cut squarely or pushed all
the way in. Tighten connections if needed.
OPERATING INSTRUCTIONS:
1. Your Dash Panel Gauge comes with an On/Off power switch. This feature allows you to shut off
power to the air compressor when compressor operations are not required.
2. Your Dash Panel Gauge is rated for maximum 150 PSI working pressure. Do not use gauge on
systems with pressure rating higher than 150 PSI.
USER MANUAL
150 PSI Illuminated Dash Panel Gauge Kit
Fig. 1
Dash Panel Gauge
Air Line
Compression
Fitting Body
Quick Splice
Connector
(Open)
Compression
Fitting Collar
Fig. 2
Wire From
Light Bulb
Connecting Wire
Quick Splice
Connector
(Closed)
USER MANUAL
150 PSI Illuminated Dash Panel Gauge Kit
Fig. 3
To Power
Source
Compressor
Inline Fuse
Air Tank
On/Off
Switch
Drain Cock
To Ground
Female Terminal
Connectors
Compressor
(+) Lead
Relay
Fig. 4
Quick Splice
Connector
To Ground
Compression
Fitting
To Pressure Switch
To Fused
86
12-Volt
Car Battery
87
30
85
To Ground
Extension Lead Wire
To Fused
Dash Panel Circuit
Pressure
Switch
Air
Line
Extension
Lead Wire
Air
Line
Fire Wall
Grommet
Air
Line
USER MANUAL
LIMITED WARRANTY:
VIAIR Corporation warrants this product, when properly installed and under normal conditions of
use, to be free from defects in workmanship and materials for a period of one year from its original
date of purchase. To receive warranty service or repair, please contact VIAIR Corporation.
Returns should be made within one year of the date of purchase, after a Return Goods Authorization
(RGA) number has been assigned by VIAIR Corporation. To obtain RGA, fax a copy of your receipt
to (949) 585-0188. For complete warranty details, please visit: www.viaircorp.com/warranty
PLEASE NOTE:
THIS WARRANTY COVERS PRODUCT DEFECTS ONLY; IT DOES NOT COVER INCIDENTAL
OR CONSEQUENTIAL DAMAGES AS RESULT OF MISUSE OR ABUSE.
15 EDELMAN • IRVINE, CA 92618
TEL: (949) 585-0011 • FAX: (949) 585-0188
www.viaircorp.com
Loading...