Vestil SLG-6, SLG-10 User Manual

STEEL STORAGE SHED MODEL SHED-5932-F

ASSEMBLY MANUAL

VESTIL MANUFACTURING CORP.

2999 NORTH WAYNE STREET, P.O. BOX 507, ANGOLA, IN 46703

TELEPHONE: (260) 665-7586 -OR- TOLL FREE (800) 348-0868

FAX: (260) 665-1339

URL: WWW.VESTILMFG.COM EMAIL:

SALES@VESTIL.COM

NOTE: Compliance with regulations, codes, and/or standards actually incorporated into law enforced in the location where the product is used is exclusively the responsibility of the end user.

PRODUCT INTRODUCTION

Thank you for purchasing a SHED-5932-F model Steel Storage Shed. Each shed includes the following features: panels protected from rust by zinc-plating; angled roofline to prevent rain accumulation on the roof; lockable door latch that incorporates a 5/16in. opening for a padlock (not included); and an open-floor design. Although assembly and use are relatively intuitive, all persons who might participate in the assembly or use of this product must familiarize themselves with the instructions provided in this manual.

Product Name

SHED-5932-F

Overall Dimensions Height x Width x Depth in inches (metric equivalents)

Additional shed specifications appear in the table below:

Door Opening Dimensions Height x Width in Inches (metric equivalents)

59 x 32 x 78¾

(149.9cm x 81.3cm x 200cm)

72½ x 30½

(184.2cm x 77.5cm)

Net Weight in Pounds (kg)

(~40kg)

SAFETY PRINCIPLES

Vestil Manufacturing Corp. recognizes the critical importance of workplace safety. Employers are

responsible for instructing employees to assemble and use the product properly. Employees and any other person, who participates in the assembly of this product or uses the shed must read and understand every instruction BEFORE assembling or using it. If you do not understand an instruction, ask your supervisor or employer for clarification.

Although Vestil diligently strives to identify foreseeable hazardous situations that might arise during the course of assembly or use, this manual cannot address every conceivable danger. The end-user must exercise sound judgment at all times. Vestil is not liable for any injury or property damage that occurs as a consequence of failing to apply the assembly or use instructions that appear in this manual.

This manual classifies personal injury risks and situations that could lead to property damage with SIGNAL WORDS. These signal words announce an associated safety message. The reader must understand that the signal word chosen indicates the seriousness of the described hazard.

Identifies a hazardous situation which, if not avoided, WILL result in DEATH or SERIOUS

Identifies a hazardous situation which, if not avoided, COULD result in DEATH or

Indicates a hazardous situation which, if not avoided, COULD result in MINOR or

Identifies practices likely to result in product/property damage, such as operation that might

INJURY. Use of this signal word is limited to the most extreme situations.

SERIOUS INJURY.

MODERATE injury.

damage the shed.

SAFETY GUIDELINES

Failure to read and understand the instructions included in this manual before assembling or using the shed constitutes misuse of the product.

Electrocution might result if the shed contacts electrified wires. Reduce the likelihood of

electrocution by applying common sense.

 DO NOT assemble or install the shed in an area where contact with electrified wires is possible.  DO NOT use the shed as a shelter during electrical storms.

Reduce the likelihood of serious personal injuries that could result from improper of careless assembly or use of this product:  DO NOT use a structurally damaged shed. Periodically inspect the shed for damage. DO NOT use the shed if it is

structurally damaged.

 Follow the assembly instructions in this manual; the shed might be unsafe to use if improperly or carelessly assembled.  DO NOT stack items on top of the shed. The roof panel will not support much weight, and because the roof is angled,

items will slide off of the roof.

 DO NOT climb on or allow others to climb on the shed.

FIG. 1: Exploded parts diagram

Part

no.

1L 78in. x 30¼ in. rear wall panel 1

1R 78in. x 30¼ in. rear wall panel 1

2L (74.8 – 77.9)in. x 30.3in. side wall 1

2R (74.8 – 77.9)in. x 30.3in. side wall 1

5R 72.6in. x 30.3in. door 1 20A 59.4in. front/back roof channel 2 20B 59.4in. rear wall (top) channel 1

20C 59.4in. rear wall (bottom) channel 1 20D 59.4in. front wall (top) channel 1 20E 59.4in. front wall (bottom) channel 1 21A 30¼ in. top channel for side panel 1 21B 30¼ in. bottom channel for side panel 1

Description Quantity

3 33.7in. x 30.3 in. roof panel 2 4 74.8in. x 27.9in. front panel 1

Part

Description Quantity

no.

22 74.7 in. door frame side channel 1 23 30.5 in. door frame bottom channel 1 31 57.4 in. rear wall brace 1

32 28.3 in. side wall brace 1 33R 26.5 in. front wall brace 1 41A 74.7 in. left side door jamb 1 41B 74.7 in.. right side door jamb 1

42 30.5in. doortop jamb 1

50 33.7in. roof side channel 1

Hardware

Item

Description Quantity Hardware

10mm self-

tapping screw

120

16mm self-

tapping screw

/16in. – ¾in.

hex head bolt

/16in. hex nut 8

3mm x 10mm

rivet

Item

Description Quantity

Door latch 1

Door latch keeper 1

Sleeve anchor

bolt

Wall bracket 3

L-type channel

cap

4mm x 10mm

rivet

Anchor bolt

bracket

Reinforcing

bracket

R-type channel

Screw concealing

cap

cover

Tools required to assemble the shed: Electric drill (1) Cordless drill (1) Measuring tape (1) Rubber mallet (1) Adjustable crescent wrench or

/16in. crescent wrench (1) Personal protective equipment: gloves & eyewear Phillips head screw driver (1) Drill bits: 10mm masonry drill bit; 8mm bit; 4mm bit; and 3mm bit. Pencil or marker (1) Pop rivet gun (1) 6ft. self-supporting step ladder (2)

+ 8 hidden pages