Vestax PMC-270A User Manual

Professional Mixing Controller
OWNER'S MANUAL
VESTAX CORPORATION
VESTAX America
VESTAX(Europe)Ltd.
The lighting flash with arrowhead symbolwithin an equilateral triangleis intended to alert the user to the presence of uninsulateddangerous voltagewithin the product's enclosure that may be of sufficient magnitude to consitute a risk of electric shock to persons
The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenanceservicinginstructions in the literature accompanying the appliance
T0 REDUCE THE RISK 0F FIRE 0R ELECTRlC SHOCKDO NOT EXPOSE THIS APPLIANCE T0 RAIN 0R M0ISTURE
WARNING
CAUTIONTO PREVENT ELECTRIC SHOCK,MATCH BLADE OF PLUG TO WIDE SLOTFULLY INSERT ATTENTIONP0UR EVITER LES CH0CS ELECTRIQUESINTRODUIRE LA LAME LA PLUS LARGE DE LA
FICHE DANS LA BORNE CORRESP0NDANTE DE LA PRISE ET P0USSER JUSQUAU F0ND
CAUTION
RISK OF ELECTRIC SHOCK DO NOT OPEN
CAUTl0NTO REDUCE THE RlSK OF ELECTRlC SHOCK
DO NOT REMOVE COVEROR BACK
NO USER-SERVICEABLE PARTS INSIDE
REFER SERVlCING T0 QUALIFIED SERVlCE PERSONNEL
1. Read all the instructions before using the product.
2.
Do not use this product near water - for example, near a bathtub, washbowl, kitchen sink, in a wet basement, or near a swimming pool, or the like.
3.
This product should be used only with a cart or stand that is recommended by the manufacturer.
4.
This product, either alone or in combination with an amplifier and headphone or speakers, may be capable of producing sound levels that could cause permanent hearing loss. Do not operate for a long period of time at a high volume level or at a level that is uncomfortable. Without. you should consult an audiologist.
5.
The product should be location or position does not interfere with its proper ventilation.
6.
The product should be located away from heat sources such as radiators, heat registers, or other products that produce heat.
7. The product should be connected to a power supply only of the type described in operating instructions or as marked on the product.
8. The power - supply cord of the product should be unplugged from the outlet when left unused for a long period of time.
9.
Care should be taken so that objects do not fall and liquids are not spilled into the enclosure through openings.
10.
The product should be serviced by qualified service personnel when ; A. The power - supply cord or the plug has been damaged ; B. Objects have fallen, or liquid has been spilled into the
product ; or C. The product has been exposed to rain ; or D. The product does not appear to operate normally or
exhibits a marked change in perfromance ; or E. The product has been dropped, or the enclosure damaged.
11. Do not attempt to service the product beyond that described in the use - maintenance instructions. All other servicing should be referred to qualified service personnel.
IMPORTANT SAFETY INSTRUCTIONS
SAVE THESE INSTRUCTIONS
WARNING : When using electric products, basic precaution should always be followed,
including the following :
CONGRATULATIONS
Thank you for purchasing the VESTAX PMC-270AProfessional Mixing ControllerAs The top of the line, the PMC-270A is a high specification mixer designed to meet the most professional requirements of the Dance Music DJs. Please read this owner's manual carefully before you start to use your mixer, so that you will fully understand all of the special features and enjoy the full use of the product.
FEATURES
Three band isolator switch kills each frequency range completely in quick action.
Pre / Post selectable AUX send switch enables various effect processing. The effect signal can be controlled by a dedicated return level control knob, the signal can be also monitored by headphone when "return" is selected by cue button.
The new option meter allows DJs to monitor the cue signal visually. The tempo can be matched by eyes as well as ears.
Three phono and 6 line inputs are provided to meet the new mixing style with various input source.
User replaceable 60 m/m input faders and 45 m/m cross fader make "on sight service" very easy. Optional input rotary volume can be replaced with the fader for "House" application.
Line 4 input jack (RCA) is located on the top panel. This allows DJs to use hand carried DAT or MD player mixing with installed equipment.
IMPORTANT
To prevent electric shock, do not remove the cover. No user serviceable parts inside. Please refer servicing to a VESTAX Authorized Service Center. Always disconnect all equipment from the main supply when disconnecting or reconnecting signal leads. The power cord should be connected last. Make sure that the power switch is off when connecting the power cord. Disconnect from AC supply when equipment is not used for extended amount of time.
WARRANTY
The warranty might vary from country to country. Each distributor has their own warranty system in accordance with the country or state regulations or laws. VESTAX observes the manufacturing countrys regulations.
PRECAUTIONS
Humidity and dust
Avoid use where there is high humidity and dust which may cause damage to internal parts.
Temperature
Avoid use in hot, (over 35)and cold, (below 5℃) locations. Keep the unit away from extreme direct heat such as direct sunlight, heating radiators, or closed vehicles.
Power cord handling
Connecting the power cord to other cords or joining cords together can cause fire and electric shock. This is extremely dangerous. Take precaution when handling AC plugs and connectors. Handle only the plug or connector and do not perform these operations with wet hands.
Keep away from liquids
Do not stand cans containing liquids on or near the equipment. If liquid enters equipment, disconnect the power cord from the power outlet immediately.
2
1
MAXMIN
PHONO 1
LINE 1
LINE 2
PGM 1LINE 4 IN
MIC
PGM1 ISOLATOR
PGM2 ISOLATOR
PHONES IN
INPUT
PRE OFF
POST
OFF
POST
OFF
POST
ONOFF
EFFECT
LOW MID HI LOW MID HI
CUE
OFF
POST
ONOFF
EFFECT
CUE
SIGNAL
TRIM
LR
MAXMIN
MIC-1
MIC-1 MIC-2
MAXMIN
MIC-2
+16dB-16dB
HI
+12dB-12dB
MID
+16dB-16dB
PRE
+16dB-16dB
+12dB-12dB
+16dB-16dB
PRE
+16dB-16dB
+12dB-12dB
+16dB-16dB
LOW
RL
BAL
EQ
+16dB-16dB
HI
+16dB-16dB
LOW
EQ
ONOFF
EFFECT
CUE
SIGNAL
HI
EQ
ONOFF
EFFECT
CUE
ONOFF
CUE
SIGNAL
HI
EQ
MAXMIN
PHONO 2
LINE 3
LINE 4
SUB
INPUT
TRIM
MID
LOW
RL
BAL
MAXMIN
PHONO 3
LINE 5
LINE 6
PGM 2
EFFECT
MASTER
MONITOR
INPUT
MASTER CUE
TRIM
MAXMIN
SEND
MAXMIN
RETURN
RL
BAL
MAXMIN
LEVEL
SPLIT CUE
PHONES
IN
MAXMIN
ON OFF
PHONES
LEVEL
MID
LOW
RL
BAL
LR
+8 +8 +5 +5 +3 +3 +1 +1
0 0
-1 -1
-3 -3
-5 -5
-7 -7
-10 -10
-15 -15
POWER
POWER
0
1
2
3
4
5
6
7
8
9
10
0
1
2
3
4
5
6
7
8
9
10
0
1
2
3
4
5
6
7
8
9
10
PRO FESSIONAL MIXING CONTROLLER
PROGRAM INPUT SECTION
PMC-270A
MICROPHONE AND SUB INPUT SECTION
ISOLATOR SECTION
MASTER
SECTION
TOP PANEL
PROGRAM
INPUT SECTION
PROGRAM INPUT SECTION
1. INPUT SELECTOR Used to select input (2 line or 1 phono) to be sent to each PGM channel.
2. TRIM CONTROL Adjusts the Input level of each channel. Set INPUT FADER to 7- 8position. adjust TRIM so that the INPUT LEVEL METER shows about 0dB.
3. BALANCE CONTROL Adjusts the stereo balance for each PGM channel. Can be used for adjusting the unbalanced stereo image caused by a strong anti-skating setting. Clockwise rotation from center position increases the volume of R over L channel. A counter clockwise rotation increases the volume of L channel over R.
4. EQUALIZER(HI,MID,LOW) Adjusts the HI, MID, LOW frequencies for each PGM channel. Each band has following specifications.
HI 8kHz ±12dB Shelving type MID 500Hz ±16dB Peaking type LOW 80Hz ±12dB Shelving type
5. EFFECT SWITCH This switch enables the signal from each programs to be sent to AUX send jack. Different signal routes can be selected this switch to different positions.
P R E : The signal before the input fader ( after the EQ ) will be sent to AUX
output. POST : The signal after the input and cross fader will be sent to AUX output. OFF : No signal will be sent to AUX output.
6. CUE SWITCH Used to send the signal from each program to monitor section for headphone monitoring.
7. INPUT FADER Used to adjust the Input level of each program. Usually set at the 7-8 position. This is a detachable
fader for the ease of replacement. Replace with the IF-27 when it is worn out.
HOW TO REPLACE THE INPUT FADER
Remove four screws which hold the fader unit panel.
Take the unit out with the panel Carefully remove the multi-cable connector from the fader unit.
Insert the connector to the new fader unit.
Put the fader unit panel in position and tighten the screws.
8. CROSS FADER When the Input level of PGM1 and PGM2 are properly set, PGM1 will be heard with the cross fader set to the left side. PGM2 will be heard with the cross fader set to the right side. When the cross fader is set in the center, both programs will be heard. This is detachable fader for the ease of replacement with CF-R when it is worn out.
Remove four screws.
Remove four screws.
Remove the multi­cable connector from fader unit.
Remove the multi-cable connecter from fader unit.
1
INPUT
PHONO 1
TRIM
2
BAL
3
EQ
HI
MID
4
LOW
EFFECT
5
6
CUE
SIGNAL
7
PGM 1
LINE 2
LINE 1
MAXMIN
RL
+16dB-16dB
+12dB-12dB
+16dB-16dB
PRE OFF
POST
ONOFF
10
9 8 7 6 5 4 3 2 1 0
MICROPHONE, SUB INPUT SECTION
LINE 4 IN
MIC
OFF
POST
ONOFF
EFFECT
CUE
LR
MAXMIN
MIC-1
MIC-1 MIC-2
MAXMIN
MIC-2
+16dB-16dB
HI
+16dB-16dB
LOW
EQ
14
9
11
10
12
13
MICROPHONE, SUB INPUT SECTION
9. LINE INPUT JACK(LINE4)
Input connectors for line level equipment such as CD players,tape decks ,DATs, or MDs etc.
10. MIC INPUT JACK(MIC1,2) Input jacks of mic1, mic2.
11. MIC LEVEL Adjusts the input level from all of the microphone inputs.
12. MIC EQUALIZER(HI,LOW) Adjusts the HI and LOW frequencies for all of the microphone input.
13. EFFECT SWITCH Used when sending signal to the external effect processor connected to the effect SEND/RETURN.
14. CUE SWITCH Used to send the signal from the mic channel to the monitor section for headphone monitoring.
MASTER SECTION
15. MASTER OUT LEVEL METER The LED level meters indicate the signal level of the line out.
16. CUE LEVEL METER The LED level meters indicate the signal level of PGM input selected by CUE SWITCH.
17. EFFECT SEND LEVEL Used to adjust the output level from EFFECT SEND JACK. The signal is selected by the effect switch.
18. EFFECT RETURN LEVEL Used to adjust the input level from the EFFECT RETURN JACK. This EFFECT RETURN can be used as the sub line input.
19. EFFECT CUE SWITCH Used to send the signal from EFFECT RETURN JACK to the monitor section for headphone monitoring.
20. MASTER BALANCE VOLUME Adjusts the signal balance of left to the right side of the outputs from the OUTPUT jack on the rear panel.
21. MASTER LEVEL VOLUME Adjust the signal level output from the output jack on the rear panel.
22. SPLIT CUE SWITCH When this switch is ON, the master signal is always heard through the right earcup of the headphone. The CUE signal will be heard in the left earcup when that input is selected by the CUE SWITCH (5, 14). This enables both programs to be monitored simultaneously,thus assisting in beat mixing.
23. HEAD PHONE LEVEL Adjusts the headphone output level.
24. HEAD PHONE JACK Use this jack to connect the headphones the impedance 8ohm to 600ohm can be used, 150ohm is recommended.
ONOFF
CUE
EFFECT
MASTER
MONITOR
MASTER CUE
MAXMIN
SEND
MAXMIN
RETURN
RL
BAL
MAXMIN
LEVEL
SPLIT CUE
PHONES
IN
MAXMIN
ON OFF
PHONES
LEVEL
LR
+8 +8 +5 +5 +3 +3 +1 +1
0 0
-1 -1
-3 -3
-5 -5
-7 -7
-10 -10
-15 -15
POWER
POWER
24
23
22
21
20
19
18
17
16
15
MASTER SECTION
PGM 2 SUB PGM 1OUTPUT EFFECT
R
R
L
L
MASTER OUT 1
R
R
L
L
SEND
ON
OFF
LINE 6
RL
LINE 5
PHONO 3
RLLINE 2
LINE 1
PHONO 1
LINE 3
PHONO 2
RETURN
GNDGND
MADE IN CHINA
SERIAL NO.
AC230V 50 / 60Hz 16W
PMC-270A
POWER
MASTER OUT 2
28 30 31
34
33
35
32
29
REAR PANEL
28. POWER SWITCH The first LED of MASTER OUT LEVEL METER that is located on the top panel is lit when on.
29. AC POWER CABLE
30.
OUTPUT JACK
(1/4inch PHONE JACK, RCA PIN JACK)
Connect to the input of power amplifier.
31. EFFECT SEND JACK Connect the SEND jacks to the input of an external effector unit(Delay,Reverb etc)
32. EFFECT RETURN JACK Connect the RETURN jacks to the output of the effector.
33. PHONO INPUT JACK Input jack for PGM1,PGM2 and SUB channel turntables. Connect turntables equipped with the MM pick up cartridge only.
34. LINE INPUT JACK Input connectors for the line level equipment such as CD players, tape decks, DATs, MDs.
35, GROUND TERMINAL
Connect this terminal to the ground lead of the turntable. This helps to reduce noise and hum.
REAR PANEL
ISOLATOR SECTION
25, HI SWITCH
Allows cutting off the sound of treble range. Sound volume will be cut when the switch is set downwards. When the switch is put back, the output volume returns to normal. Can be useful for cutting off the sound of the cymbals or high hats for example.
26, MID SWITCH
Allows cutting off the sound of the middle range. Sound volume will be cut when the switch is set downward position. When the switch is put back, the output volume becomes normal sound volume. Can be used for cutting off vocal and melody from the source.
27, LOW SWITCH
Allows cutting off the sound of the bass range. Sound volume will be cut when the switch is set downward. When the switch is put back, the output volume return to normal. Can be utilized for creating the effects of an acapella.
PGM1 ISOLATOR
LOW MID HI
252627
ISOLATOR SECTION
Vestax Corporation
Specification
NOMINAL INPUT LEVELIMPEDANCE PHONO 42dB470k LINE 10dB47k MIC 42dB303k EFFECT RCV 10dB47k
RATED OUTPUT LEVELIMPEDANCE LINE OUT 4dB10KΩ REC OUT 10dB10kΩ EFFECT SEND 10dB10kΩ
FREQUENCY RESPONSE
20Hz20kHz (+0,−3dB)
S/N RATIO 80dB
DIMENSION (
WXHXD
) W290
mm
XH80mmXD380
mm
WEIGHT 5kg
Loading...