Vestax PMC-07PRO D User Manual

Vestax Corporation

1-18-6 Wakabayashi, Setagaya-ku,Tokyo 154-0023 Japan

PROFESSIONAL MIXING CONTROLLER

OWNER'S MANUAL

Phone [phone] Fax [phone]

Vestax (Europe) Ltd.

Unit 5 RiverweyIndustrial Park Alton Hampshire GU34 2QL England, U.K.
Phone [phone] Fax [phone]
Web : www.vestax.co.uk

Vestax Technical Center of America

8489 W. Third Street Ste. 1044 Los Angleles, CA 90048
Phone [phone] Fax [phone]

CONGRATULATIONS!

Thank you for purchasing the VESTAX PMC-07ProD. Please read this owner's manual carefully before you start to
use in order to understand fully how it to operate your new mixer.

FEATURES

The new Vestax Digital Fader System consists of coils and a permanent magnet.There is no contact between
these parts. Therefore, neither the element or magnet gets degraded or damaged even after hard usage.
Unlike an optical type fader, the digital fader system does not get effected even by liquid spills or dusts.
Control of the fader curve by a complete digital signal system, enabling creation of sharp edges in the curve
pattern.

FUNCTIONS

TOP PANEL

Curve pattern switch (a) selects the crossfader curve
pattern.

Setting the C.F. FINE CONTROL to minimum, the
crossfader curve is most sharp, moving the control
clockwise, towards max, gradually reduces the
sharpness of the curve (b).

(a) CURVE PATTERN SWITCH

(b) C.F. FINE CONTROL

The replacement crossfader unit for PMC-07ProD is
"CF-X".
"CF-05PRO", "CF-PCV" cannot be substituted in this
mixer.

MIC MASTER

SUBMIC MAINMIC

MAXMIN MAXMIN

+12

0

-12

dB dB

LO HI LO MID H I

LRLRLR

DIGITALFADER CONTROL

4

3

2

1

CURVEPATTERN

C.F.FINE

MAX

MIN

PGM 1

PGM REV

NORMAL

REVERSE

MAX

MIN

EQ EQEQ

+6

-24

BALANCEPAN BALANCE

PGM 1 PGM 2

LINE1

LEVEL LEVEL

+6

+3

0

-3

-6

-10

-20

PHONO1

10

9

8

7

6

5

4

3

2

1

0

GAIN

LO MID HI

PGM 2

MAX

MIN

LINE

2

10

9

8

7

6

5

4

3

2

1

0

PROFESSIONALMIXING CONTROLLER

GAIN

21

PHONO2

LEVEL

MAX

MIN

SESSION MIX

MONITOR SELECT

MAXMIN

MASTER

CUE

MONITOR LEVEL

MAX

MIN

C.F. MONITOR

PHONES

POWER

PGM2PGM1

FRONT PANEL

INPUT FADER CURVE adjustments for PGM1 + PGM2.

PROFESSIONALMIXING CONTROLLER

PGM 1 CROSSFADER PGM 2

I.F.REV. I.F.REV.C.F.REV.

NORMAL NORMAL NORMAL

REVERSE

CURVE CURVE

REVERSE REVERSE

PHONES

PRE-SET CURVE

Using curve pattern switch,select the crossfader curve pattern from SHAPE1- 4,to set the cross­fader pattern.

SHAPE 1:

3

2

1

SHAPE 2:

3

2

1

SHAPE 3:

3

2

1

C.F. FINE CONTROL : MIN

4

As this curve shape is very sharp, it is
used for hard scratch play.
Setting C.F. FINE CONTROL to
minimum, the curve sharp is most
sharp. As the switch moves closer to
max, the curve sharpness reduces.

C.F.POSITION

4

4

This curve shape is "A" type curve.

In this position, switching C.F. FINE
CONTROL from MIN to MAX, the

C.F. FINE CONTROL : MIN

C.F.POSITION

C.F. FINE CONTROL : MIN

C.F. FINE CONTROL : MAX

C.F. FINE CONTROL : MAX

crossfader curve shape changes
from slow slope curve to sharp slope
by 8 steps.

C.F. FINE CONTROL : MAX

SHAPE 4:

3

2

1

C.F.POSITION

C.F. FINE CONTROL : MIN

C.F.POSITION

4

This curve shape is rectangle wave type. Moving the crossfader from right to left or from
left to right, it performs like a "transformer scratch". Switching C.F. FINE CONTROL, the 8
patterns crossfader curve shape can be selected. It enables selection of the 8 patterns of
curve shape as fig 1- fig 8 below.

fig-2

fig-3 fig-4fig-1

fig-7fig-6fig-5

fig-8

C.F. FINE CONTROL : MAX