Vertiv Liebert IntelliSlot WEBRT3N User Manual

Liebert® IntelliSlot™
WEBRT3N™Card

User Manual

Technical Support Site

If you encounter any installation or operational issues with your product, check the pertinent section of
this manual to see if the issue can be resolved by following outlined procedures. Visit
https://www.VertivCo.com/en-us/support/ for additional assistance.

TABLE OF CONTENTS

1 Introduction 5

1.1 Features 5

1.1.1 Features 5

1.2 Applications 5

1.2.1 IS-WEBRT3N Card Web Interface 5

1.2.2 Liebert Web Card Provides Shut-down Utilities 5

2 What’s Included 7

3 Installation 9

4 UPS Web management by IS-WEBRT3N Card 11

4.1 Introduction 11

4.2 IS-WEBRT3N Card UPS Web Interface 11

4.2.1 Information 11

4.2.2 Basic Information 12

4.2.3 Current Status 12

4.2.4 Remote Control 12

4.2.5 Meter/Chart 13

4.3 Configuration 13

4.3.1 UPS Configuration 13

4.3.2 UPS On/Off Schedule 14

4.3.3 Network 15

4.3.4 SNMP 16

4.3.5 E-mail 18

4.3.6 SMS 19

4.3.7 WEB/Telnet 19

4.3.8 System Time 20

4.3.9 Language 21

4.4 Log Information 21

4.4.1 Event Log 21

4.4.2 Data Log 21

4.4.3 Battery Test Log 22

4.5 Help 22

4.5.1 About 22

5 Telnet—Remote Monitoring 23

5.1 Introduction 23

5.2 Telnet Configuration 23

6 Shut-down Utility 25

Vertiv | Liebert® IS-WEBRT3N™ Card User Manual| 3

Vertiv | Liebert® IS-WEBRT3N™ Card User Manual| 4

1 INTRODUCTION

1.1 Features

The Liebert IS-WEBRT3N card is a new generation SNMP (Simple Network Management Protocol) UPS
monitoring product. The card permits remote control of the UPS and enables reporting its current status.

The IS-WEBRT3N card is simple and easy to install: insert the card into a compatible UPS, install the
Liebert DeskPro-Net™ software on the included CD on a Windows® operating system and configure the IP
address. All other configuration may be done with a Web browser.

NOTE: Anti-virus software may prevent the identification of devices. If no cards are detected, disable
the anti-virus software. After the card is identified, you may re-enable anti-virus software without
interfering with device monitoring.

The IS-WEBRT3N card also provides shut-down, using Power Insight, for different operating systems. It
can be configured to send a shut-down command for such events as utility power failure and low battery.

1.1.1 Features

• Provides SNMP MIB to monitor and control UPS

• Auto-senses 10M/100M fast Ethernet

• Manages and configures via Telnet, Web browser or NMS

• Supports TCP/IP, UDP, SNMP, Telnet, SNTP, PPP, HTTP, SMTP protocol

• Supports HTTPS encryption for fully secure web-based management

• Sends both SNMP traps and e-mails for event notification

• Automatically e-mails a daily UPS history

• Matches with shut-down software to protect computer’s file saving and shut down safely

1.2 Applications

1.2.1 IS-WEBRT3N Card Web Interface

The system administrator can use a Web browser to check the status of all UPSs where a IS-WEBRT3N
has been installed. The administrator can access a UPS by entering its IP address in the browser. When
utility power surges, sags or fails, the IS-WEBRT3N can, if so configured, also send the trap information to
the system manager to take proper action.

1.2.2 Liebert Web Card Provides Shut-down Utilities

A computer on the network with the IS-WEBRT3N card and DeskPro-Net Utility installed can locate all IS­WEBRT3N cards on the network. Power Insight can be set up to close open files and perform a graceful
system shut-down when a UPS with a IS-WEBRT3N card experiences an input power failure or low
battery.

Vertiv | Liebert® IS-WEBRT3N™ Card User Manual| 5

This page intentionally left blank.

Vertiv | Liebert® IS-WEBRT3N™ Card User Manual| 6

2 WHAT’S INCLUDED

• Liebert IS-WEBRT3N card

• Liebert Web Card CD, including:

• DeskPro-Net Utility: Configure Liebert Web Card UPS IP address, update firmware

• Liebert IS-WEBRT3N card user manual

• Liebert IS-WEBRT3N card MIB

Figure 2.1 Liebert IS-WEBRT3N card

Vertiv | Liebert® IS-WEBRT3N™ Card User Manual| 7

This page intentionally left blank.

Vertiv | Liebert® IS-WEBRT3N™ Card User Manual| 8

3 INSTALLATION

Before using the Liebert Web Card, the hardware and software configuration is necessary.

1. Install the IS-WEBRT3N card in the Liebert IntelliSlot®bay on the UPS.

The bay may be protected with a plastic cover.

2. Attach an RJ-45 Ethernet cable, CAT5 or better, to the card and to your network.

3. Install Liebert DeskPro-Net Utility on your computer.

a. Insert the included DeskPro-Net Utility CD in the monitoring computer.

b. Follow the prompts to install the software.

After complete installation, DeskPro-Net Utility will appear in Start>Programs.

Figure 3.1 IS-WEBRT3N installation

Figure 3.2 Installation steps

Vertiv | Liebert® IS-WEBRT3N™ Card User Manual| 9