Vertical Vertical - MBX IP - (donated by Ray from - Vertical) Vertical SBX - IP Installation Guide 3.5

Download

Inst allation Guide

Release 3.5

June 2010

Release 3.5

June 2010

Vertical Communications, Inc. reserves the right to revise this publication and to make

Release 3.5

June 2010

changes in content without notice.

This publication contains proprietary an d confidential information of Vertical Communications, Inc. The contents of this document may not be disclosed, copied or translated by third parties, in any form, or by any means known, or not now known or conceive d, without pr ior explicit written permission from Vertical Communications, Inc.

LIMIT OF LIABILITY/DISCLAIMER OF WARRANTY Vertical Communications, Inc. makes no representation or warranties with respect to the

accuracy or completeness of the content of this publication and specifically disclaims any implied warranty of merchantability or fitness for any particular purpose, and shall not be liable for any loss of profit or any other commercial damage, including but not limited to, special, incidental, or consequential.

TRADEMARKS Vertical Communications and the Vertical Communications logo and combinations thereof

are trademarks of Vertical Communications, Inc. All other brand and product names are used for identification only and are the property of their respective holders.

RESTRICTED RIGHTS LEGEND Use, duplication, or disclosure of the technical data cont ained in this document b y the Gov-

ernment is subject to restrictions as set forth in subdivision (c) (1) (ii) of the Rights in Technical Data and Computer Software clause at DFARS 52.227-7013 and/or in similar or successor clauses in the FAR, or in the DOD or NASA FAR Supplement. Unpublished rights reserved under the Copyright Laws of the United States. Contractor/manufacturer is Vertical Communications, Inc., 10 Canal Park, Suite 602, Cambridge, MA 02141-2249.

REVISION HISTORY

Release 3.5

June 2010

Release Date Documentation Changes Page No.

3.5 06-10 Update -- EKSU (p/n 4002-03) now shows 16-port capability. 2-4 and 4-9 Update -- dial pad graphic has been modified. 6-14

3.0 11-09 Release 3.0 added the following new hardware: --

MBU (p/n 4000-03) to accommodate 3.0 boards. 4-2 EMBU (p/n 4002-03) to accommodate 3x16 Expansion board 4-8 3x16 Expansion board (p/n 4032-16) 4-14

T1/PRI board (p/n 4035-00) 4-16 Updated the Voicemail specifications with recording times. 4-21 A section has been added that addresses "Loading a 2.5

database onto a 3.0 system". Added a System Upgrade Configuration procedure. 7-10 Added a T1/PRI Firmware Upgrade procedure. 8-16

2.1 09-08 Formatting & editing have been done to certain sections for greater ease of understanding. No features have been added or removed.

2.0 07-08 25-pair cable pin outs have been added (p/n 4099-00). 4-7 A VoIB software upgrade procedure (web-based) has been

added. Added information on KSU administration via RJ-45 LAN port by

direct connection and by connection to the KSU over a LAN switch.

A "BLF Manager" section has been added. 6-16 A section has been added that addresses uploading new VMIB

prompts. A system setup quick reference Appendix has been added. Appendix A A section has been added that addresses IP Phones on the

SBX IP.

1.0 01-08 Initial Release NOTE: this document contains information on ISDN, DCOB, and

SMS. These features are currently not supported. Information pertaining to DID pertains only to SIP Trunking.

7-8

8-13

9-17

8-9

5-22

Release 3.5

June 2010

Chapter 1 Introduction

Important Safety Instructions - - - - - - - - - - - - - - - - - - - - - - - - - 1-1

Safety Requirements - - - - - - - - - - - - - - - - - - - - - - - - - - - - 1-1 Precautions - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 1-2 Cautions - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 1-2 Disposal of Old Units - - - - - - - - - - - - - - - - - - - - - - - - - - - - 1-3

Using this Manual - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 1-4

Chapter 2 System Overview

SBX IP System Highlights - - - - - - - - - - - - - - - - - - - - - - - - - - - 2-1

Supported phones - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 2-1 System Connection Diagram - - - - - - - - - - - - - - - - - - - - - - - - - 2-2 System Components - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 2-3

Basic KSU (p/n 4000-00) - - - - - - - - - - - - - - - - - - - - - - - - - 2-3

Expansion KSU (p/n 4002-00) - - - - - - - - - - - - - - - - - - - - - 2-3

KSU (p/n 4000-03) for 3.0 s/w or higher - - - - - - - - - - - - - - 2-4

EKSU (p/n 4002-03) for 3.0 s/w or higher - - - - - - - - - - - - - 2-4 System Specification Tables - - - - - - - - - - - - - - - - - - - - - - - - - 2-5

Board Capacities - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 2-5

System Capacities - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 2-6

Dialing Specifications - - - - - - - - - - - - - - - - - - - - - - - - - - - 2-7

Dimensions and Weight - - - - - - - - - - - - - - - - - - - - - - - - - - 2-7

Environmental Specifications - - - - - - - - - - - - - - - - - - - - - - 2-7

Electrical Specifications - - - - - - - - - - - - - - - - - - - - - - - - - - 2-8

Chapter 3 KSU Installation

Pre-Installation - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 3-1

Safety Installation Instructions - - - - - - - - - - - - - - - - - - - - - 3-1

Installation Precautions - - - - - - - - - - - - - - - - - - - - - - - - - - 3-2

SBX IP Installation Guide

Contents TOC-2

Release 3.5

June 2010

Wiring Precautions - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 3-2

KSU Installation - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 3-3

Unpacking - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 3-3 KSU Exterior and Dimension - - - - - - - - - - - - - - - - - - - - - - - 3-4 Opening and Closing the Front Cover - - - - - - - - - - - - - - - - 3-5 Frame Ground Connection - - - - - - - - - - - - - - - - - - - - - - - - 3-7 External Backup Battery Installation - - - - - - - - - - - - - - - - - - 3-8 KSU Mounting - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 3-9

Expansion KSU Installation - - - - - - - - - - - - - - - - - - - - - - - - - - 3-12

Unpacking - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 3-12 Connecting the Expansion KSU to the Basic KSU - - - - - - - 3-13 Expansion KSU Mounting - - - - - - - - - - - - - - - - - - - - - - - - 3-15

Chapter 4 Board Installation

Basic Board Installations - - - - - - - - - - - - - - - - - - - - - - - - - - - - 4-2

Main Board Unit (p/n: 4000-00) - - - - - - - - - - - - - - - - - - - - - 4-2 Main Board Unit (p/n: 4000-03) - - - - - - - - - - - - - - - - - - - - - 4-2 Modular Jack (MJ1 - MJ3) Pin Assignment - - - - - - - - - - - - - 4-4 Switch, LED, and Connector - - - - - - - - - - - - - - - - - - - - - - - 4-6 SBX 25-Pair Installation Cable Pinouts - - - - - - - - - - - - - - - - 4-7

Expansion Main Board Unit (EMBU) - - - - - - - - - - - - - - - - - - - - 4-8

Expansion MBU (p/n: 4002-00) - - - - - - - - - - - - - - - - - - - - - 4-8 Expansion MBU (p/n: 4002-03) - - - - - - - - - - - - - - - - - - - - - 4-8 Modular Jack (MJ1 - MJ3) Pin Assignment - - - - - - - - - - - - 4-10

CO Line and Extension Boards - - - - - - - - - - - - - - - - - - - - - - - 4-12

3x8 Expansion Board (3 CO Line and 8 Hybrid) - - - - - - - - 4-12 3x16 Expansion Board (3 CO Line and 16 Digital) - - - - - - - 4-13

Other Board Installations (optional) - - - - - - - - - - - - - - - - - - - - 4-14

Digital Telephone Interface Board (DTIB16) - - - - - - - - - - - 4-14 Modem Function Unit (MODU) - - - - - - - - - - - - - - - - - - - - 4-15 T1/PRI Interface Board - - - - - - - - - - - - - - - - - - - - - - - - - - 4-16 VoIB -- Voice Over Internet Protocol Board (4ch) - - - - - - - 4-18 Voice Mail Interface Board (VMIB) - - - - - - - - - - - - - - - - - - 4-21

SBX IP Installation Guide

Contents TOC-3

Release 3.5

June 2010

Chapter 5 Terminal Connection and Wiring Method

Terminal and Doorbox Models - - - - - - - - - - - - - - - - - - - - - - - - 5-1 Terminal Cabling Distance - - - - - - - - - - - - - - - - - - - - - - - - - - 5-3 Basic Terminal Connection - - - - - - - - - - - - - - - - - - - - - - - - - - 5-4

DKT and DSS - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 5-4

SLT - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 5-4

Doorbox - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 5-5 Connecting Additional Terminals - - - - - - - - - - - - - - - - - - - - - - 5-7

External Music Source Wiring - - - - - - - - - - - - - - - - - - - - - 5-8

Relay Contacts - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 5-8

External Paging Port Wiring - - - - - - - - - - - - - - - - - - - - - - - 5-8

Alarm Detection Wiring - - - - - - - - - - - - - - - - - - - - - - - - - - 5-8 Cable Wiring - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 5-9

Wall Mount Wiring - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 5-9

Rack Mount Wiring - - - - - - - - - - - - - - - - - - - - - - - - - - - - 5-10 IP Phones on the SBX IP - - - - - - - - - - - - - - - - - - - - - - - - - - 5-11

Supported IP phones: - - - - - - - - - - - - - - - - - - - - - - - - - - 5-11

Minimum requirements - - - - - - - - - - - - - - - - - - - - - - - - - 5-11

IP endpoint licensing - - - - - - - - - - - - - - - - - - - - - - - - - - - 5-12

IP Addressing - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 5-12

Preparation - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 5-14

PCAdmin Connection - - - - - - - - - - - - - - - - - - - - - - - - - - 5-14

Configuring IP phone settings - - - - - - - - - - - - - - - - - - - - 5-20

Programming VoIP card settings from a digital station - - - 5-22

Chapter 6 Starting the SBX IP System

Before Starting the SBX IP System - - - - - - - - - - - - - - - - - - - - 6-1 Basic Programming - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 6-2

DKT Programming - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 6-2

Entering the Programming Mode - - - - - - - - - - - - - - - - - - - 6-5

Pre-Programming - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 6-6 BLF Manager - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 6-16

BLF Manager Installation - - - - - - - - - - - - - - - - - - - - - - - - 6-16

BLF Manager in detail - - - - - - - - - - - - - - - - - - - - - - - - - - 6-17

SBX IP Installation Guide

Contents TOC-4

Release 3.5

June 2010

System list window (Status of systems) - - - - - - - - - - - - - - 6-17 Station list window (Extension status) - - - - - - - - - - - - - - - - 6-18 Network traffic window - - - - - - - - - - - - - - - - - - - - - - - - - - 6-18 File menu - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 6-18

Chapter 7 Using Database Upload/Download

PC Requirement - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 7-1 Connection Method with SBX IP - - - - - - - - - - - - - - - - - - - - 7-1

Installation - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 7-2

Main software components - - - - - - - - - - - - - - - - - - - - - - - - 7-2 Choosing Up/Download and Connection Type - - - - - - - - - - 7-2 User Information Dialog - - - - - - - - - - - - - - - - - - - - - - - - - - 7-3

Starting Database File Upload/Download - - - - - - - - - - - - - - - - - 7-6

Transferring Process - - - - - - - - - - - - - - - - - - - - - - - - - - - - 7-7 Finishing DataBase File Upload/Download - - - - - - - - - - - - - 7-7

Loading a 2.5 Database into a 3.0 System - - - - - - - - - - - - - - - - 7-8

Loading the Database - - - - - - - - - - - - - - - - - - - - - - - - - - - - 7-8 Example -- System Upgrade Configuration - - - - - - - - - - - - 7-10

Chapter 8 Upgrade Process

Software Upgrade - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 8-1

Minimum PC Requirement - - - - - - - - - - - - - - - - - - - - - - - - 8-1 Connection Method with SBX IP - - - - - - - - - - - - - - - - - - - - 8-1

Installation - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 8-2

File Component in the Execution Directory - - - - - - - - - - - - - 8-2 Choosing Up/Download and Connection Type - - - - - - - - - - 8-2 User Information Dialog - - - - - - - - - - - - - - - - - - - - - - - - - - 8-3

Starting Software Upgrade - - - - - - - - - - - - - - - - - - - - - - - - - - - 8-6

Transferring Process - - - - - - - - - - - - - - - - - - - - - - - - - - - - 8-7 Completing Software Upload - - - - - - - - - - - - - - - - - - - - - - - 8-7

Uploading new VMIB prompts - - - - - - - - - - - - - - - - - - - - - - - - - 8-9

Prerequisites: - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 8-9 Upgrading Voice Prompts - - - - - - - - - - - - - - - - - - - - - - - - - 8-9

VoIB Software Upgrade by Web-based Connection - - - - - - - - 8-13 T1/PRI Firmware Upgrade - - - - - - - - - - - - - - - - - - - - - - - - - - 8-16

SBX IP Installation Guide

Contents TOC-5

Release 3.5

June 2010

Verify network settings - - - - - - - - - - - - - - - - - - - - - - - - - 8-16

Downloading firmware file - - - - - - - - - - - - - - - - - - - - - - - 8-16

Chapter 9 Remote Diagnostics

Introduction - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 9-1

Hardware/Software Minimum Requirements - - - - - - - - - - - 9-1

Hardware Configuration - - - - - - - - - - - - - - - - - - - - - - - - - - 9-2

Installing Software - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 9-2

Uninstalling Software - - - - - - - - - - - - - - - - - - - - - - - - - - - - 9-3

Important Notes for Users - - - - - - - - - - - - - - - - - - - - - - - - 9-3

Full Screen Layout - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 9-4 File Menu - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 9-4

Open Sub-menu - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 9-5

Capture On Sub-menu - - - - - - - - - - - - - - - - - - - - - - - - - - 9-5

Capture Off Sub-menu - - - - - - - - - - - - - - - - - - - - - - - - - - 9-5 Connection Menu - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 9-6

Serial Port Connection with SBX IP System - - - - - - - - - - - - 9-6

Modem Connection with the SBX IP System - - - - - - - - - - - 9-9

LAN Connection with the SBX IP System - - - - - - - - - - - - 9-17 Commands Menu - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 9-28

Executing Commands - - - - - - - - - - - - - - - - - - - - - - - - - - 9-29

Functions of Commands - - - - - - - - - - - - - - - - - - - - - - - - 9-31 View Menu - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 9-46

Toolbar Sub-menu - - - - - - - - - - - - - - - - - - - - - - - - - - - - 9-46

Command Bar Sub-menu - - - - - - - - - - - - - - - - - - - - - - - 9-47

Input Box Bar Sub-menu - - - - - - - - - - - - - - - - - - - - - - - - 9-47

Clear New Sub-Menu - - - - - - - - - - - - - - - - - - - - - - - - - - 9-47 Help Menu - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 9-48

About SBX Remote Diagnostic Tool Sub-menu - - - - - - - - 9-48 Data Display Area - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 9-49

Data Display Functions - - - - - - - - - - - - - - - - - - - - - - - - - 9-49

Automatic Data Storing Functions - - - - - - - - - - - - - - - - - - 9-50 VoIB Maintenance - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 9-51

SBX IP Installation Guide

Contents TOC-6

Release 3.5

June 2010

Chapter 10 Troubleshooting

Symptons and Solutions - - - - - - - - - - - - - - - - - - - - - - - - - - - - 10-1

Appendix A System Setup Quick Reference

Quick Start - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - A-1

To initialize the system database: - - - - - - - - - - - - - - - - - - A-1 To set the KSU admin password: - - - - - - - - - - - - - - - - - - - A-1 To set the KSU LAN port IP address: - - - - - - - - - - - - - - - - A-1 Default passwords - - - - - - - - - - - - - - - - - - - - - - - - - - - - - A-2 RS-232 port settings - - - - - - - - - - - - - - - - - - - - - - - - - - - - A-2 Default IP address - - - - - - - - - - - - - - - - - - - - - - - - - - - - - A-2

Index

SBX IP Installation Guide

Chapter 1

Release 3.5

June 2010

Introduction

Important Safety Instructions

Safety Requirements

When using the telephone equipment, basic safety precautions should always be followed to reduce the risk of fire, electric shock, and other personal injury. Please t ake the following precautions:

• Read and understand all instructions.

• Follow all warnings and instructions as marked on the product.

• Unplug this product from the wall outlet before cleaning. A damp cloth should be used for cleaning. Do not use liquid or aerosol cleaners.

• Do not use this product near water: such as in a bathtub, sink, or swimming pool.

• Do not place this product on an unstable stan d or table. If the product falls, serious damage can result.

• Do not place this product on a bed, sofa, or other soft surface. Doing so may prevent proper ventilation for the slots in the back or botto m of the KSU (key system unit), causing the product to overheat. Do not place this product near or over a radiator or other heat source. Do not use this product for in a buil t-in installation without proper ventilation.

• Use this product only with the type of power sour ce indicated on the p roduct label. If you are not sure of the type of power supply appropriate for the intended location, consult your dealer or local power company.

• Do not allow anything to rest on the power cord. Do not place this product in an area in which might step or trip on the cord.

• Do not overload wall outlets and extension cords. This may result in fire or electric shock.

• Never push objects of any kind into this product through the slots or connectors. This risks damage to the product, as well as fire and electric shock.

• Never pour or spill liquid of any kind on the product.

• To reduce the risk of electric shock, do not disassemble thi s product. Instead, take it to a qualified person when service or repair work is required. Opening or removing covers may expose you to dangerous voltages or other risk. Incorrect reassembly can cause electric shock when the appliance is subsequently used.

SBX IP Installation Guide

Important Safety Instructions 1-2

Release 3.5

June 2010

Chapter 1: Introduction

• Unplug this product and refer servicing to qualified service personnel if/when:

• the power supply cord or plug is damaged or frayed .

• liquid has been spilled onto the product.

• the product does not operate normally by following the operating instruction s.

NOTE: Adjust only those controls that are covered by the operating

instructions. Improper adjustment of other controls may result in damage that can require extensive repair work by a qualified technician.

• the product has been dropped or the KSU has been damaged.

• the product exhibits a distinct change in performance.

• Avoid using a telephone during an ele ctrical storm, a s ther e m ay be a re mote risk of electric shock from lightning.

• In the event of a gas leak, do not use the telephone near the leak.

Precautions

• Keep the system away from heating appliances and electrical noise-generating devices such as fluorescent lamps, motors and televisions. These noise sources can interfere with the performance of the SBX IP system.

• This system should be kept free of dust and moisture, and should not be exposed to high temperature, vibration, or direct sunlight.

• Do not attempt to insert wires or pins into the system. If the system does not operate properly, the equipment should be repaired by an authorized service center.

• Do not use benzene, paint thinner, or an abrasive powder to clea n the KSU. Clean it by wiping with a soft cloth.

Cautions

• This system should be installed and serviced by qualified service personnel only.

• When a failure occurs which exposes any internal parts, disconnect the power supply cord immediately, and return the system to the dealer.

• To protect the PCB from static electricity, discharge body static before touching connectors and/or components by touchin g the gr ou nd or we ar ing a gr ou nd stra p.

Warning: There is a danger of explosion if the battery is incorrectly replaced. Replace

it only with the same or equivalent type recommended by the manufacturer . Dispose of used batteries according to the manufacturer’s instructions.

SBX IP Installation Guide

Important Safety Instructions 1-3

Release 3.5

June 2010

Chapter 1: Introduction

Disposal of Old Units

The symbol below designates a product covered by the European Directive 2002/96/EC.

• All electric and electronic products must be disposed of in

special collection facilities appointed by government or local/municipal authorities.

• The correct disposal of the old appliances will help prevent

potential negative consequences for the environment as well as human health.

• For more detailed information about disposal of the old

appliances, please contact the waste disposal service in your area, or the place of product purchase.

SBX IP Installation Guide

Using this Manual 1-4

Release 3.5

June 2010

Chapter 1: Introduction

Using this Manual

This document provides general information covering the hardware description and installation of the SBX IP system. While every effort has been taken to ensure the accuracy of this information, Vertical Communications, Inc. makes no warranty of accuracy or interpretations thereof.

Chapter 2 - System Overview

General information on the SBX IP system, including system specifications and capacity.

Chapter 3 - KSU Installation

Detailed instructions for planning the installation site, and procedures to install the SBX IP system.

Chapter 4 - Board Installation

Detailed instructions for installing components of the SBX IP board.

Chapter 5 - Terminal Connection and Wiring Method

Description of the kinds of terminals (including maximum distance) and other device connections for each terminal.

Chapter 6 - Starting the SBX IP System

Instructions for starting the system, and instructions for basic admin programming.

Chapter 7 - Using Database Upload/Download

Procedures for the upload/download of SBX IP MBU Database from/to a PC file

Chapter 8 - Upgrade Process

Procedures for upgrading the KSU software.

Chapter 9 - Remote Diagnostics

Procedures for diagnosing system problems and p erforming system maintenance from a remote site.

Chapter 10 - Troubleshooting

Information on troubleshooting common issues on the SBX IP system.

SBX IP Installation Guide

Chapter 2

Release 3.5

June 2010

System Overview

SBX IP System Highlights

Features of the SBX IP system include:

• Flexible architecture

• Simplified system structure

• Powerful PC application via LAN, Modem, RS-232C (serial port)

• Stable and enhanced voice features

• Simple installation and efficient system management:

• Remote admin and software upgrade through LAN connection

• Remote admin and software upgrade through PSTN modem

• Value-added features

• Distinctive voice mail (ADPCM 32 Kbps)

• Basic CID (CO and SLT) function

• 8 Poly internal MOH (13 music sources)

Supported phones

MODEL DESCRIPTION

7208D 8-button digital telephone 7224D 24-button digital telephone IP7008D 8-button IP telephone IP7024D 24-button IP telephone IP7024LD 24-button IP telephone (large display) Nomad IP Wireless IP telephone Nomad SP Soft Phone

SBX IP Installation Guide

System Connection Diagram 2-2

SBX IP

Release 3.5

June 2010

Chapter 2: System Overview

System Connection Diagram

The following diagram shows the components that make up the SBX IP system:

SBX IP Installation Guide

System Components 2-3

Release 3.5

June 2010

Chapter 2: System Overview

System Components

Basic KSU (p/n 4000-00)

ITEM DESCRIPTION

BKSU Power Supply Unit (PSU)

Main Board Unit (MBU) 3x8 Expansion Board (3 CO, 1 DKT, and 7 Hybrid)

OPTIONAL BOARDS:

3x8 Expansion Board 3 CO, 1 DKT, and 7 Hybrid MODU Analog Modem -- Bell, ITU-T, V.34 V.32BIS, V.90 VMIB Voice Mail Interface Board, 4 channels VoIB LAN Interface Board

NOT SUPPORTED EKSU (p/n 4002-03)

T1/PRI Board DTIB16 Board

Expansion KSU (p/n 4002-00)

ITEM DESCRIPTION

EKSU Power Supply Unit (PSU)

Expansion Main Board Unit (EMBU) 3x8 Expansion Board (3 CO, 1 DKT, and 7 Hybrid)

OPTIONAL BOARDS:

3x8 Expansion Board 3 CO, 1 DKT, and 7 Hybrid

NOT SUPPORTED KSU (p/n 4000-03)

3x16 Expansion Board

SBX IP Installation Guide

System Components 2-4

Release 3.5

June 2010

Chapter 2: System Overview

KSU (p/n 4000-03)

ITEM DESCRIPTION

BKSU Power Supply Unit (PSU)

OPTIONAL BOARDS:

3x8 Expansion Board CO Line and DKT/SLT Interface Board MODU Analog Modem -- Bell, ITU-T, V.34 V.32BIS, V.90 T1/PRI

VMIB Voice Mail Interface Board, 4 channels VoIB LAN Interface Board

NOT SUPPORTED EKSU (p/n 4002-00)

EKSU (p/n 4002-03)

ITEM DESCRIPTION

EKSU Power Supply Unit (PSU)

for 3.0 s/w or higher

Main Board Unit (MBU)

Digital trunk interface and 8 hybrid stations

for 3.0 s/w or higher

Expansion Main Board Unit (EMBU) 3x16 Expansion Board (3 CO, 16 DKT)

OPTIONAL BOARDS:

3x8 Expansion Board 3 CO, 1 DKT, and 7 Hybrid 3x16 Expansion Board 3 CO, 16 Digital ports

NOT SUPPORTED KSU (p/n 4000-00)

SBX IP Installation Guide

System Specification Tables 2-5

Release 3.5

June 2010

Chapter 2: System Overview

System Specification Tables

Board Capacities

DESCRIPTION CAPACITY BOARD

Alarm Input 1 MBU CO Line Ports 4 (Total 12) 3x8 Expansion DTMF/CPT Receiver Channels 16 chs MBU External MOH 1 MBU External Paging Port 1 MBU External Relay Contact 4 MBU (2), EMBU (2) FSK Receiver Channels 16 chs MBU Internal MOH (13 Music Sources) 1 MBU LAN 3 MBU, VoIB, E1HB8 Max Direct Station Connections

(DKT/SLT/DSS) MODEM Channel 1 MODU MODU 1 Modem Unit

Power Fail Circuits 3 MBU (1), EMBU (1), 3x8 Expansion (1) RS-232C Port 1 MBU VoIB 1 Voice over Internet Board

4 (Total 32) 3x8 Expansion

Analog Modem Bell, ITU-T, V.34 V.32BIS, V.90 Speed 300bps up to 33Kbps speed rate Connection Automatic rate negotiation

LAN Interface 10 Base-T Ethernet (IEEE 802.3) Speed 10/100 auto-negotiation, 100 Mbps

recommended Duplex Half or Full Duplex (Auto-Negotiation) VoIP Protocol H.323 Revision 4 Voice Compression -- G.711/G.726/G729/G.723.1 Echo Cancellation -- G.165

SBX IP Installation Guide

System Specification Tables 2-6

Release 3.5

June 2010

Chapter 2: System Overview

System Capacities

ITEM CAPACITY SPECIFICATION

Attendant Positions 5 - Main

1 - System Authorization Codes 200 3-11 digits each CO Line Groups 24 -Conference 3-15 Parties All ports are available

Multi-line Conference 3-15 Parties Max. 3 groups Hunt Groups 10 groups (620-629) 26 stations per group Intercom Links Non-Blocking -Last Number Redial 15-50 32 digits, via admin programming Memory Back-up Duration 10 years -Paging Zones

- All Call

- External

- Internal

1 1 10

(549) (545)

(501-510) Station Groups 10 -Station Sp eed Dial 100 (000-099) 24 digits each System Speed Dial 500 (2000-2499) 24 digits each Time Slots 128 --

SBX IP Installation Guide

System Specification Tables 2-7

Release 3.5

June 2010

Chapter 2: System Overview

Dialing Specifications

ITEM DESCRIPTION SPECIFICATION

DTMF Dialing Frequency Deviation Less than +/-1.8%

Signal Rise Time 5 ms Tone Duratio n, on time Min. 50 ms, Normally 100 ms Inter-digit Time Min. 30 ms, Normally 100 ms

Pulse Dialing Pulse Rate 10 PPS

Break/Make Ratio 60/40% or 66/33% Ring Detect Sensitivity -- 30Vrms @ 16-55Hz Ring Signal -- 75Vrms, 25Hz Switching Device -- Custom Mixed-Signal ASIC Device

Dimensions and Weight

ITEM

HEIGHT WIDTH DEPTH

(mm / in)

KSU / EKSU Cabinet 288 / 11.34 339 / 13.35 85 / 3.35 1.80 / 3.9 IP Keyset (IP7008D) 114 / 4.49 202 / 7.95 175 / 6.89 0.73 / 1.6 IP Keyset (IP7024D) 124 / 4.88 268 / 10.55 203 / 7.99 0.95 / 2.1 IP Keyset (IP7024LD) 147 / 5.79 26 8 / 10.55 243 / 9.57 1.03 / 2.3

Environmental Specifications

ITEM DESCRIPTION SPECIFICATION

Operating Environment

Temperature Humidity 0 - 80% (non-condensing)

SBX IP Installation Guide

C) – 40 (oC)

0 (

WEIGHT

(kg / lbs)

System Specification Tables 2-8

Release 3.5

June 2010

Chapter 2: System Overview

Electrical Specifications

ITEM DESCRIPTION SPECIFICATION

BatteryBackup (External) Input Voltage +24 Volt DC (+12VDC x 2ea)

Battery Fuse 5.0A @250Volt AC Charging Current Max. 200mA Battery Load Current Max. 3A (BKSU only),

Max. 6A (BKSU + EKSU) CPU -- ARM7 TDMI core (32bit, 50MHz) External Paging Port -- 0dBm @ 600ohm External Relay Contact -- 1A @ 30Volt DC Music Source Input -- 0dBm @ 600ohm Power Supply Unit (PSU) AC Voltage Input 100-240 +/- 10% Volt AC @47-63Hz

AC Power Consumption 90W AC Input Fuse 2A @250Volt AC DC Output Voltage +5, -5, +27, +30Volt DC

SBX IP Installation Guide

Chapter 3

Release 3.5

June 2010

KSU Installation

Pre-Installation

Please read the following guidelines concerning installation and connection before installing the SBX IP system. Be sure to comply with all applicable local regulations.

NOTE: Also, refer to the double-sided Quick Start Card included with the KSU.

Safety Installation Instructions

When installing the telephone wiring, basic safety precautions should always be followed to reduce the risk of fire, electric shock and personal injury. Please take the following precautions:

• Never install the telephone wiring during a lightning storm.

• Never install the telephone jack in wet or damp locations, unless the jack is specifically designed for wet locations.

• Never touch un-insulated telephone wires or terminals unless the telephone line has been disconnected at the network interface.

• Use caution when installing or modifying telephone lines.

• Anti-static precautions should be taken during installation.

SBX IP Installation Guide

Pre-Installation 3-2

Release 3.5

June 2010

Chapter 3: KSU Installation

Installation Precautions

The SBX IP system is designed for wall mounting or a free-standing rack.

DO NOT

• In direct sunlight and in hot, cold, or humid places (acceptable temperatu re range

install the system in the following situations:

= 0 to 40

• In places where shocks or vibrations are frequent or strong.

• In dusty places, or places where water or oil may come into contact with the system.

• Near high-frequency generating devices such as sewing machines or electric welders.

• On or near computers, fax machines, oth er of fice equipment, m icrowave ovens or air conditioners.

• In any manner that obstructs the openings on the to p of the SBX IP system.

• With the optional service boards stacked.

Wiring Precautions

Be sure to follow these precautions when wiring:

• Do not wire the telephone cable in parallel with an AC power source, such as a computer or fax machine. If the cables are run near those devices, shield the cables with metal tubing, or use shielded cables, and ground the shields.

• If the cables are run on the floor, use protectors to prevent the wires from being stepped on. Avoid running wire under carpets.

• Avoid using the same power supply outlet for computers, fax machine, and other office equipment. This reduces induction noise interruption when using the SBX IP near other machines.

• Make sure the power and battery switche s are OF F du rin g wiring . After wiring is completed, the power switch may be turned ON.

• Incorrect wiring may cause the SBX IP system to operate improperly. If an extension does not operate properly, disconnect the telephone from the extension line and then reconnect, or turn the system power OFF, and then ON again.

• Use twisted pair cable for connecting CO lines.

C).

SBX IP Installation Guide

KSU Installation 3-3

Release 3.5

June 2010

Chapter 3: KSU Installation

KSU Installation

Unpacking

Open the packaging and verify the items shown in the following figure are included:

SBX IP Installation Guide

KSU Installation 3-4

Release 3.5

June 2010

Chapter 3: KSU Installation

KSU Exterior and Dimension

The following diagram shows the exterior and dimensions of the KSU:

SBX IP Installation Guide

KSU Installation 3-5

Release 3.5

June 2010

Chapter 3: KSU Installation

Opening and Closing the Front Cover

Opening the Front Cover

1. Ope n the c ord co ve r, and turn the screws counter-clockwise to loosen (as shown

in Figure 3-1

2. Lift the front cover in the direction of the arrow as shown.

Figure 3-1 Opening the front cover

SBX IP Installation Guide

KSU Installation 3-6

Release 3.5

June 2010

Chapter 3: KSU Installation

Closing the Front Cover

1. Insert the front cover into the slot on the KSU (as shown in Figure 3-2

2. Put the front cover down on the KSU in the direction of the arrow shown.

3. Turn the screws clockwise to tighten and close the Cord Cover.

Figure 3-2 Closing the front cover

IMPORTANT: Prior to operation, the front cover of the SBX IP must be closed and

the screws tightened.

SBX IP Installation Guide

KSU Installation 3-7

Release 3.5

June 2010

Chapter 3: KSU Installation

Frame Ground Connection

It is very important that the frame of the SBX IP system is grounded:

1. Turn the grounding screw counter clockwise to loosen it (as shown in Figure 3-3

2. Insert the grounding wire, and tighten the screw.

3. Connect the grounding wire to an appropriate ground source (refer to Caution

below).

Figure 3-3 Grounding the KSU

CAUTION:

• The equipment should be connected to an outlet with a protective ground

connection.

• For ground wire, green-and-yellow insulation is required. In addition, the

cross-sectional area of the conductor must be more than UL 1015 AWG#18 (1.0mm). It is also recommended that the ground wire be shorter than 1m (3.28 f t).

• Proper grounding is very important to protect the SBX IP from external noise, and

to reduce the risk of electrocution in the event of lightning strike.

• You must comply with applicable local regulations.

SBX IP Installation Guide

KSU Installation 3-8

Release 3.5

June 2010

Chapter 3: KSU Installation

External Backup Battery Installation

In case of power failure, the external backup batteries automatically maintain uninterrupted power for the SBX IP system. The external batteries must provide 24V DC; this is generally accomplished by connecting two 12V batteries in a series arrangement (as shown in Figure 3-4)

Figure 3-4 External Backup Battery Installation

NOTE: The cable used to connect the battery is supplied with the KSU.

Battery operation is controlled by the PSU. The PSU provides charging current to the batteries during normal AC power operation at a maximum of about 200mA. PSU battery operation is halted if the AC power is re-connected, or if the battery voltage is too low to maintain full-system operation. The external batteries maintains system operation as needed, depending on several elements such as battery charge statu s, condition and capacity of the batteries, and system configuration (that is, number of station ports).

CAUTION:

• It is recommended that you use an external backup battery fuse (5A @ 250V) between the battery and the system.

• The recommended battery capacity is 24V/20AH MF. The SBX IP system generally operates for over 3 hours with batteries that are in good condition.

• Carefully check the battery polarity with cable colors (red and blue) when connecting the battery to the system.

• Make sure that you do not short-out the exte rn al ba tte ries an d cables.

• There is a danger of explosion if external batteries are replaced incorrectly. Be sure replacement batteries are the same as (or equivalent to) those recommended by the manufacturer. Dispose of used batteries according to the manufacturer’s instructions.

SBX IP Installation Guide

KSU Installation 3-9

Release 3.5

June 2010

Chapter 3: KSU Installation

KSU Mounting

Wall Mounting

1. Install three (3) anchor plugs into the wall using the mounting template included

for accurate placement, as shown in #1-#3 of Figure 3-5

2. Attach the mounting template with the three (3) screws (included) to the three (3)

anchor plugs #4 of Figure 3-5

3. Hook the KSU onto the screws, making sure that the system slides down

securely, as shown in Figure 3-6

Figure 3-5 Mounting Template

SBX IP Installation Guide

KSU Installation 3-10

Release 3.5

June 2010

Chapter 3: KSU Installation

Figure 3-6 Wall Mounting the KSU

SBX IP Installation Guide

KSU Installation 3-11

Release 3.5

June 2010

Chapter 3: KSU Installation

Desktop Mounting

To use the SBX IP system on top of a desk or other flat surface, use the following procedure:

1. To attach the rubber feet to the bottom of the SBX IP system as shown in Figure

3-7, first remove the protective sticker from the rubber feet.

2. After attaching the rubber feet to the BKSU and EKSU, firmly mount the EKSU

onto the BKSU.

Figure 3-7 Desktop Mounting

SBX IP Installation Guide

Expansion KSU Installation 3-12

Release 3.5

June 2010

Chapter 3: KSU Installation

Expansion KSU Installation

Unpacking

Figure 3-8 EKSU Carton Contents

SBX IP Installation Guide

Expansion KSU Installation 3-13

Release 3.5

June 2010

Chapter 3: KSU Installation

Connecting the Expansion KSU to the Basic KSU

To connect the Expansion KSU to the Basic KSU, perform the following steps:

1. Remove the “dummy” of each KSU.

2. Use the link cable to connect the Basic KSU to the Expansion KSU (as shown

in Figure 3-9

3. To secure the link cable, turn the screw clockwise to tighten, and then tie the link

cable with tie cable (as shown in Figure 3-10

Figure 3-9 Connecting KSUs

SBX IP Installation Guide

Expansion KSU Installation 3-14

Release 3.5

June 2010

Chapter 3: KSU Installation

Figure 3-10 EKSU to BKSU Connection

NOTE:

• If AC power fails, the last SLT port on the EMBU automatically connects to CO1.

• If power to the EKSU is turned off while both systems (BKSU and EKSU) are working properly, the BKSU automatically restarts.

SBX IP Installation Guide

Expansion KSU Installation 3-15

Release 3.5

June 2010

Chapter 3: KSU Installation

Expansion KSU Mounting

NOTE: Do not make any link cable connections between the BKSU and EKSU until they both are

properly wall mounted or rack mounted.

EKSU Wall Mounting

1. Install the EKSU within 5 centimeters of the basic system.

2. Install three (3) anchor plugs into the wall using the mounting template included

for accurate placement. The KSU can be mounte d eit he r vertically or horizontally.

3. Screw the included three (3) screws into the three (3) anchor plugs (as shown

in Figure 3-11

Figure 3-11 EKSU Mounting Template

SBX IP Installation Guide

Expansion KSU Installation 3-16

Release 3.5

June 2010

Chapter 3: KSU Installation

4. Hook the Expansion KSU onto the installed screws, making sure that the system slides down securely (Figure 3-12

Figure 3-12 EKSU Wall Mounting

SBX IP Installation Guide

Chapter 4

Release 3.5

June 2010

Board Installation

While installing boards, be aware of the following:

CAUTION:

• Power must be turned OFF before and during board installation.

• To protect the system from static electricity, do not touch the boards.

To discharge static, touch a grounded object or wear a grounding strap.

• Insert the boards carefully to avoid bending connector pins (male pins on

MBU/EMBU). Misaligning can damage the boards.

To install the board, perform the following steps:

• Before inserting the board, remove the dummy slot (as shown in #1 of Figure 4-1

• Hold the board (as shown in #2 of Figure 4-1

direction of the arrow so that the board securely en ga g es with the con ne ct or (CN2) on the main board (as shown in #3).

), and carefully insert the board in the

Figure 4-1 Board Installation

SBX IP Installation Guide

Basic Board Installations 4-2

Release 3.5

June 2010

Chapter 4: Board Installation

Basic Board Installations

Main Board Unit (p/n: 4000-00)

The MBU controls the communication between the peripheral interfaces, supervises all resources in the system, controls the gain adjustment of the PCM signal, generates the system tones, and manages system call processing.

Figure 4-2 MBU

Main Board Unit (p/n: 4000-03)

This MBU performs all the same functions as the MBU shown above. This unit was modified to accommodate expanded capabilities such as the T1/PRI board and the 3x8 Expansion board.

(Also, this unit has been pre-loaded with the 3.0 software, or higher.)

SBX IP Installation Guide

Basic Board Installations 4-3

Release 3.5

June 2010

Chapter 4: Board Installation

NOTE: If AC power fails, the last SLT port on the MBU automatically connects to CO1.

The MBU is installed in the KSU, and it provides various types of connectors and RJ11 modular jacks for the connection of peripheral boards and miscellaneous functions (refer to Figure 4-2

, Figure 4-3, and Table 4-1).

Figure 4-3 MBU Connection Ports

Table 4-1 Connectors

SWITCH/CONNECTOR FUNCTION COMMENT

CN1 KSU Connection to EKSU with Link

cable CN2 3x8 Expansion Installation 50 pins CN4 MODU Installation 20 pins CN5 VMIB 32 pins CN6 JTAG Port for Emulator For Test CN7 PSU Connection (+5V, -5V, +30V) 7 pins CN8 RS-232C Port Connection 9 pins CN13 External Relay Contact 4 pins CN14 VoIB Installation 16 pins

SBX IP Installation Guide

50 pins

Basic Board Installations 4-4

Release 3.5

June 2010

Chapter 4: Board Installation

Table 4-1 Connectors (continued)

SWITCH/CONNECTOR FUNCTION COMMENT

MJ1 3 CO Lines Connection 3 arrays

MJ2-1 1 DKT or Alarm Sensor

MJ2 MJ3 LAN 1 LAN

PJ1 (Red) External MOH Connection PJ2 (Blue) External Page Conne ction SW1 4 Poles DIP Switch for Software Usage Default = All ON SW2 Lithium Battery ON/OFF Switch for

SW3 System Reset Button SW4 JTAG Reset Enable/Disable Switch Not Assembled

MJ2-2-8 7 DKTs or 7 SLTs Connection

Memory & RTC Backup

8 arrays

Default = OFF

Modular Jack (MJ1 - MJ3) Pin Assignment

MBU MJ1 (CO)

Table 4-2 MBU1 - 1, 2, 3

CONNECTOR PIN NUMBER SIGNAL NAME

1, 2 n/a 3, 4 CO-T, CO-R 5, 6 n/a

MBU MJ2 (Extension)

Table 4-3 MBU MJ2 - 1 (DKT Only)

CONNECTOR PIN NUMBER SIGNAL NAME

1n/a 2DKT-T

3, 4 Alarm_Detection

5DKT-R 6n/a

SBX IP Installation Guide

Basic Board Installations 4-5

Release 3.5

June 2010

Chapter 4: Board Installation

Table 4-4 MBU MJ2 - 2, 3, 4, 5, 6, 7, 8

CONNECTOR PIN NUMBER SIGNAL NAME

1n/a 2DKT-T

3, 4 SLT-T, SLT-R

5DKT-R 6n/a

NOTE: When installing DKTs or SLTs on Hybrid Ports (MJ2-2,3,4 ,5,6,7,8), keep the

pin assignment (as shown above in Table 4-4). Otherwise the DKTs or SLTs will not operate normally.

Table 4-5 Terminal DKT

CONNECTOR PIN NUMBER SIGNAL NAME

1n/a 2RING

3, 4 Reserved

5TIP 6n/a

Table 4-6 Terminal SLT

CONNECTOR PIN NUMBER SIGNAL NAME

1, 2 n/a 3, 4 TIP, RING 5, 6 n/a

CN13 Pin Assignment (Relay Contact)

Table 4-7 CN13

CONNECTOR NO SIGNAL NAME

1 Relay 1 - pin 1 2 Relay 1 - pin 2 3 Relay 2 - pin 1 4 Relay 2 - pin 2

SBX IP Installation Guide

Basic Board Installations 4-6

Release 3.5

June 2010

Chapter 4: Board Installation

Table 4-8 MJ3 Pin Assignment (LAN)

CONNECTOR PIN NUMBER SIGNAL NAME FUNCTION

4, 5, 7, 8 reserved

1 TX+ Transmit Data 2 TX- Transmit Data 3 RX- Receive Data 6 RX+ Receive Data

Switch, LED, and Connector

Table 4-9 SW1 Functions

SWITCH FUNCTION OFF ON (DEFAULT)

1-1 Administration Programming Access Disable Enable 1-2 Command/Event Trace (Software Testing ) Enabl e Disable 1-3 Simplified Message Desk Interface control

(SMDI - Voice Mail)

1-4 Database Default on Power Up Disable Enable

SMDI ON SMDI OFF

Before programming the system, Switch 1-4 (as shown above in Table 4-9) should be set to ON. The power should then be cycled OFF, and back ON to initialize the default system database. Once the dat abase has been initialized, switch 1-4 sh ould be placed in the OFF position to protect the database.

To protect the RAM/RTC data, set the SW2 lithium battery switch to the ON position, then install the option boards to the MBU.

CAUTION:

• The SW2-DIP switch should be set to the ON position to protect the system database in case of power failure.

• Replace the batteries (when needed) with the same or equivalent type recommended by the manufacturer. The system will not function normally if the batteries are replaced incorrectly.

• Dispose of used batteries according to manufacturer’s instructions and/or local government regulations.

• After the system powers up and initializes, the 4th pole of SW1 should be set to the OFF to position to protect the features being programmed in Admin Programming.

SBX IP Installation Guide

Basic Board Installations 4-7

Release 3.5

June 2010

Chapter 4: Board Installation

SBX 25-Pair Installation Cable Pinouts

SBX IP Installation Guide

Expansion Main Board Unit (EMBU) 4-8

EKSU p/n (4002-03) supports 16 digital stations

Release 3.5

June 2010

Chapter 4: Board Installation

Expansion Main Board Unit (EMBU)

Expansion MBU (p/n: 4002-00)

The Expansion Main Board Unit provides the following feat ur es :

• DKT and SLT Interface circuits

• Ring Generation circuit

• External Relay contacts for LBC or general purpose

• Peripheral Device Decoding circuit

• Master Clock Generation circuit

• PFT circuit [CO1

• PCM Voice Processing circuit with ACT2 (ASIC, voice switching including DSP) device for PCM tone generation and PCM gain control.

⇔ the last SLT port (STA8)]

Expansion MBU (p/n: 4002-03)

Figure 4-4 EMBU

This “all digital” EMBU provides the same features and functionality as the EMBU described above. This unit was modified to accommodate expanded system capabilities such as the DTIB16 card which supports 16 digital stations.

SBX IP Installation Guide

Expansion Main Board Unit (EMBU) 4-9

Release 3.5

June 2010

Chapter 4: Board Installation

NOTE:

• If AC power fails, the last SLT port on the EMBU automatically connects to CO1.

• If power to the EKSU is turned off while both systems (BKSU and EKSU) are working properly, the BKSU automatically restarts.

Figure 4-5 EMBU Connection Ports

Table 4-10 Connector/Modular Jack/Switch Functions

SWITCH/CONNECTOR FUNCTION COMMENT

CN1 KSU Connection from BKSU with Link cable 50 Pins CN2 CO and Extension Board (3x8 Expansion) installation 50 Pins CN7 PSU connection 7 Pins

CN13 External Relay contact 4 Pins

MJ1 3 CO connection 3 Arrays MJ2 16 DKT 8 Arrays

Table 4-11 LED Indications

LED DESCRIPTION

LED1 (Blue) Periodic Toggle - ON, 300 msec; OFF, 300 mse c

SBX IP Installation Guide

Expansion Main Board Unit (EMBU) 4-10

Release 3.5

June 2010

Chapter 4: Board Installation

Modular Jack (MJ1 - MJ3) Pin Assignment

EMBU MJ1(CO)

Table 4-12 EMBU MJ1 - 1, 2, 3

CONNECTOR PIN NUMBER SIGNAL NAME

1, 2 n/a 3, 4 CO-T, CO-R 5, 6 n/a

Table 4-13 EMBU MJ2 - 1, 2, 3, 4, 5, 6, 7, 8

CONNECTOR PIN NUMBER SIGNAL NAME

1n/a 2DKT-T

3, 4 SLT-T, SLT-R

5DKT-R 6n/a

Rel. 3.0

-------->

2 & 5 DKT1

3, 4 DKT2

NOTE: When installing DKTs or SLTs on Hybrid Ports, (MJ2 -2,3,4,5,6,7,8), keep the

pin assignment (as shown above in Table 4-13

). Otherwise the DKTs or SLTs

will not operate normally.

Table 4-14 Terminal DKT

CONNECTOR PIN NUMBER SIGNAL NAME

1n/a 2RING

3, 4 reserved

5TIP 6n/a

SBX IP Installation Guide

Expansion Main Board Unit (EMBU) 4-11

Release 3.5

June 2010

Chapter 4: Board Installation

Table 4-15 Terminal SLT

CONNECTOR PIN NUMBER SIGNAL NAME

1, 2 n/a 3, 4 TIP, RING 5, 6 n/a

CN13 Pin Assignment (Relay Contact)

Table 4-16 CN13

CONNECTOR NO SIGNAL NAME

1 Relay 1 - pin 1 2 Relay 1 - pin 2 3 Relay 2 - pin 1 4 Relay 2 - pin 2

SBX IP Installation Guide

CO Line and Extension Boards 4-12

Release 3.5

June 2010

Chapter 4: Board Installation

CO Line and Extension Boards

3x8 Expansion Board (3 CO Line and 8 Hybrid)

The 3x8 Expansion Board can be installed on th e CN2 connector of the MBU or EMBU, and provides three (3) CO/PBX Loop Start CO Line interfaces that support Pulse/DTMF signaling. Each interface contains ring and loop current circuits, A/D and D/A conversions, as well as pulse signaling circuitry.

This board also provides eight Hybrid ports (eight DKTs or eight SLT interfaces), and can detect FSK signal for incoming Caller ID, DTMF signal for incoming caller ID, and a call progress tone. It also provides three ( 3) o n-h ook co nne ctio n paths for CID/SMS.

BOARD LINE

3x8 Expansion 3 CO & 8 SLT or 8 DKT RJ11 3 CO Line and

Figure 4-6 3x8 Expansion Board

CONNECTOR

TYPE

DESCRIPTION CABLE

8 Hybrid Interface

DKT : 4 wire CO, SLT : 2 wire

SBX IP Installation Guide

CO Line and Extension Boards 4-13

Release 3.5

June 2010

Chapter 4: Board Installation

Modular Jack (MJ1-MJ2) Pin Assignment

Table 4-17 3x8 Expansion Board MJ1 - 1, 2, 3

CONNECTOR PIN NUMBER SIGNAL NAME

1, 2 n/a 3, 4 CO-T, CO-R 5, 6 n/a

Table 4-18 3x8 Expansion Board MJ2 - 1, 2, 3, 4, 5, 6, 7, 8

CONNECTOR PIN NUMBER SIGNAL NAME

1n/a 2DKT-T

3, 4 SLT-T, SLT-R

5DKT-R 6n/a

3x16 Expansion Board (3 CO Line and 16 Digital)

IMPORTANT: The 3x16 Expansion Board can ONLY be installed on the “modified”

MBU (p/n 4000-03) or EMBU (p/n 4002-03)

The 3x16 Expansion Board can be optionally installed on the CN2 connector of the “modified” MBU or EMBU, and provides three (3) CO/PBX Loop Sta rt CO Line interfaces that support Pulse/DTMF signaling. Each interface contains ring and loop current circuits, A/D and D/A conversions, as well as pulse signaling circuitry.

This board also provides 16 Digital ports (16 DKT interfaces), and can detect FSK signal for incoming Caller ID, DTMF signal for incoming caller ID, and a call progress tone. It also provides three (3) on-hook connection paths for CID/SMS.

BOARD LINE

3x16 Expansion

NOTE: The modular jack pin assignments are the same as the 3x8 Expansion Board,

3 CO & 16 DKT RJ11 3 CO Line and

see Table 4-17

andTable 4-18 above.

SBX IP Installation Guide

CONNECTOR

TYPE

DESCRIPTION CABLE

DKT : 4 wire

16 Digital Interface

CO : 2 wire

Other Board Installations (optional) 4-14

DTIB16

Release 3.5

June 2010

Chapter 4: Board Installation

Other Board Installations (optional)

Digital Telephone Interface Board (DTIB16)

The Digital Telephone Interface Board (DTIB) can be optionally installed to provide digital voice and data communications to/fr om 16 digital telephones. An RJ11 type female connector is mounted on the front edge of the b oard for connection to the station interfaces.

• The EMBU (p/n 4002-03) can support two DTIB16 boards to increase th e number of ports to 32.

• Notice the board-specific pinouts shown in Figure 4-7

• The DTIB16 is configured in PGM 101-103.

Figure 4-7 Installation of the DTIB16 Board

SBX IP Installation Guide

Other Board Installations (optional) 4-15

Release 3.5

June 2010

Chapter 4: Board Installation

Modem Function Unit (MODU)

MODU provides analog modem connection. The MODU can be optionally inst alled on the MODU connectors (CN4) of the MBU. The MODU supports Bell, ITU-T, V.34, V.32BIS, and V.90 protocols at a speed rate of 300bps up to 33Kbps. It also supports automatic rate negotiation.

Figure 4-8 Installation of the MODU Board

SBX IP Installation Guide

Other Board Installations (optional) 4-16

SW3 System Reset button

The Default is all OFF

The Default is ON (PRI)

SW4

PRI T1

LD1 LD2 LD3 LD4 LD5 LD6 LD7 LD8 LD9

9 10 11 12 13 14 15 16

STA STA STA STA STA STA STA STA

LED

Release 3.5

June 2010

Chapter 4: Board Installation

T1/PRI Interface Board

The T1/PRI interface board board provides a full T1/PRI digital trunk interface and 8 hybrid stations. The board also supports both full and fractional T1/PRI circuits in clusters of 4.

This interface supports either 24 PCM channels for T1 or 23 PCM channels for PRI. Nine (9) loop start CO lines can be used in addition to the T1/PRI channels. The T1/PRI includes the Ethernet port.

This board can be used as either a T1 or a PRI by changing the onboard DIP switch. By default, switch SW4 is set to the ON position (PRI).

CAUTION: The T1/PRI board can only be used with MBU p/n: 4000-03.

SBX IP Installation Guide

Other Board Installations (optional) 4-17

Release 3.5

June 2010

Chapter 4: Board Installation

LED Indications

LED SPECIFICATION

LED1 PRI - In Use and blinking slowly if active

T1 - In Use LED2 ON - RX Carrier Loss LED3 ON - Out of frame LED4 ON - Yellow Alarm LED5 ON - RX all 1 LED6 ON - Loop back mode LED7 PRI - ON: Multiframe Establish Alarm

T1 - ON: Blinking slowly if active LED8 ON - reserved LED9 ON - TE LED10* Blue ON - In Use of one of 8 HYBRID extensions of PRHB8 board

* LED 10 is not related to PRI/T1 trunk operation. It is only related to

8 extensions use state of PRHB8 board

SBX IP Installation Guide

Other Board Installations (optional) 4-18

Release 3.5

June 2010

Chapter 4: Board Installation

VoIB -- Voice Over Internet Protocol Board (4ch)

The VoIB can be optionally installed on the MBU, and provides four VoIP channels. The length of the Ethernet cable should be less than ten (10) meters.

Figure 4-9 VoIB

The VoIB can be installed on the basic MBU, and provides the Etherne t interface for software applications and VoIP features with an optional VoIP daughter board.

The VoIB ha s the capacity for maximum four (4) channels with o ne (1) V oIB. The VOIU provides an additional four (4) VoIP channels.

ITEM SPECIFICATION

LAN Interface 10 Base-T Ethernet (IEEE 802.3) Speed 10/100 auto-negotiati on, 100 Mbps recommended Duplex Half Duplex or Full Duplex (Auto-Negotiation) VoIP Protocol H.323 Revision 4 Voice Compression G.711/G.726/G.729/ G.723.1 Voice/Fax Switching T.38 Echo Cancellation G.165 Dual SIP / H.323

protocol support ITU-T H.323 v4 & H.450

standard compliance

Supports H.323 fast connect, early H.245, and H.245 tunneling Supports H.323 Gatekeeper register, direct and route calls Inband / out of band DTMF transmission

SBX IP Installation Guide

Other Board Installations (optional) 4-19

Release 3.5

June 2010

Chapter 4: Board Installation

ITEM SPECIFICATION

SIP RFC 2543/3261 standard compliance

Supports IPKTS Protocol

Supports Inband / RFC 2833 / Out of band (INFO) DTMF transmission

for Vertical IP phones Codecs G.711A/u-law, G.723.1(5.3k/6.3k), G.729/G.729A NAT friendly for IP phones --

Various switch and connector functions

SWITCH/CONNECTOR FUNCTION

SW1 VoIB Reset Switch for CPU (S32510A) SW2 Pole 2: Boot mode selection, others: reserved.

Default: Pole 2 (ON), Others (OFF) CN1 JTAG (Joint Test Action Group) for debug CN2 RS-232C Trace Tool Connection CN3 and CN4 VOIU Board Connection CN5 MBU Connection MJ1 Network (RJ-45) Cable Connection

LED SPECIFICATION

LED1 (yellow) Channel1 seize indication LED (ON:Busy, OFF:Idle) LED2 (yellow) Channel2 seize indication LED (ON:Busy, OFF:Idle) LED3 (yellow) Channel3 seize indication LED (ON:Busy, OFF:Idle) LED4 (yellow) Channel4 seize indication LED (ON:Busy, OFF:Idle) LED5 (yellow) Channel5 seize indication LED (ON:Busy, OFF:Idle) LED6 (yellow) Channel6 seize indication LED (ON:Busy, OFF:Idle) LED7 (yellow) Channel7 seize indication LED (ON:Busy, OFF:Idle) LED8 (yellow) Channel8 seize indication LED (ON:Busy, OFF:Idle) LED9 (red) VOIU DSP operation status LED (ON: Normal, OFF: Fail) LED10 (red) VoIB DSP operation status LED (ON: Normal, OFF: Fail) LED1 1 DSP HINT interrupt LED (ON: Active, OFF: Idle) MJ1-LD2 (yellow) Speed Status LED (OFF: 10Mbps) MJ1-LD1 (green/orange) Link Status LED (ON: Link, Flashing: Data Transfer)

SBX IP Installation Guide

Other Board Installations (optional) 4-20

Release 3.5

June 2010

Chapter 4: Board Installation

Pin assignment

Table 4-19 MJ3 Pin Assignment (LAN)

CONNECTOR PIN NUMBER SIGNAL NAME FUNCTION

4, 5, 7, 8 RESERVED

1 TX+ Transmit Data 2 TX- Transmit Data 3 RX- Receive Data 6 RX+ Receive Data

NOTE: 10BASE-T runs on Category 5 UTP or higher.

VOIU -- Internet protocol unit (4ch)

The VOIU can be optionally installed on the VoIB. It provides four (4) VoIP channels.

Figure 4-10 Installation of the VOIU Board

SBX IP Installation Guide

Other Board Installations (optional) 4-21

Release 3.5

June 2010

Chapter 4: Board Installation

Voice Mail Interface Board (VMIB)

The Voice Mail In terface Board (VMIB) can be optionally installed on CN5 of the MBU. It provides the capability for system announcements, UCD announcements, and user greetings.

Figure 4-11 Installation of the VMIB Board

Table 4-20 Voicemail Specifications

ITEM 2-hour VMIB 8-hour VMIB

Channel 4 Channels 4 Channels Max Record Time:

Prompt System Greeting (announcement)

User Record Time Max Number of User Voice Messages 800 800 Number of system greeting (for all users in system) 01-70 01-70

NOTE: MBU SW1-4 and SW2 control the protection of recorded messages. NOTE: You can tell the 8-hour VMIB from the 2-hour VMIB by checking the label on

8 Min. 24 Min. 99 Min.

10 Min. 40 Min.

480 Min.

the VMIB. The 8-hour VMIB is labeled 4000-80.

SBX IP Installation Guide

Other Board Installations (optional) 4-22

Release 3.5

June 2010

Chapter 4: Board Installation

SBX IP Installation Guide

Chapter 5

7208D

Release 3.5

June 2010

Terminal Connection and Wiring Method

Terminal and Doorbox Models

MODEL DESCRIPTION

7208D 8-button digital telephone 7224D 24-button digital telephone

-- 48-button DSS Console

-- 2-port digital Doorbox

Figure 5-1 Vertical 7208 Telephone for SBX IP

SBX IP Installation Guide

Terminal and Doorbox Models 5-2

7224D

DSS Doorbox

Release 3.5

June 2010

Chapter 5: Terminal Connection and Wiring Method

Figure 5-2 Vertical 7224 Telephone for SBX IP

Figure 5-3 Vertical DSS and Doorbox for SBX IP

SBX IP Installation Guide

Terminal Cabling Distance 5-3

Release 3.5

June 2010

Chapter 5: Terminal Connection and Wiring Method

Terminal Cabling Distance

Figure 5-4 Terminal Cable Distance

SBX IP Installation Guide

Basic Terminal Connection 5-4

Release 3.5

June 2010

Chapter 5: Terminal Connection and Wiring Method

Basic Terminal Connection

DKT and DSS

Figure 5-5 Connecting a DKT to the system

Table 5-1 DKT and DSS Connection Pin Assignment

CONNECTOR PIN NUMBER NO SIGNAL NAME

1n/a 2DKT-T

3, 4 Reserved

5DKT-R 6n/a

SLT

Figure 5-6 Connecting an SLT to the system

Table 5-2 SLT Connection Pin Assignment

CONNECTOR PIN NUMBER NO SIGNAL NAME

1, 2 n/a 3, 4 TIP, RING 5, 6 n/a

SBX IP Installation Guide

Basic Terminal Connection 5-5

Release 3.5

June 2010

Chapter 5: Terminal Connection and Wiring Method

Doorbox

The Doorbox is an intercom unit that can be installed at the entrance to a building for communication between visitors and employees inside.

By pressing a CALL button, a visitor can communicate with a person inside the building who has a phone with a “call coverage” flex button associated with the Doorbox.

Installation

SBX IP Installation Guide

Basic Terminal Connection 5-6

Release 3.5

June 2010

Chapter 5: Terminal Connection and Wiring Method

Operating Instructions

The following examples describe how calls are handled when sent through the Doorbox.

Call FROM the Doorbox

A visitor can press the CALL button once or the External switch once, depending on the setup.

• The visitor hears music from the Doorbox until station user answers the call.

• The station with the call coverage flexible button associated with the Doorbox also rings, and the call coverage button LED illuminates.

INT: Refer to the Programming Guide ("Intercom Box Signaling" in Station Attributes).

• The station user answers the call by going off-hook using the handset or by pressing the SPEAKER button for speakerphone operation.

Call TO the Doorbox

The station user can go off-hook and press a flexib le button that is pre-programming with the

Doorbox station number, or dial the number

associated with the doorbox.

SBX IP Installation Guide

Connecting Additional Terminals 5-7

Release 3.5

June 2010

Chapter 5: Terminal Connection and Wiring Method

Connecting Additional Terminals

The MBU provides connections for one external music sour ce, one external page port, one relay contact, and an alarm detection inpu t monitor through the PJ1 (RED, External MOH) and PJ2 (BLUE, External Page) audio jacks and an MJ3 (RJ11 Modular Jack) as shown in Figure 5-7

Figure 5-7 Adding Terminals

SBX IP Installation Guide

Connecting Additional Terminals 5-8

Release 3.5

June 2010

Chapter 5: Terminal Connection and Wiring Method

External Music Source Wiring

The MBU accommodates one external music port through a PJ1 (RED) audio jack.

Relay Contacts

The MBU/EMBU provides two (2) relay contacts that are used for a loud bell or other general purposes through pin No. 1-4 of CN13.

External Paging Port Wiring

The MBU supports one external paging port through a PJ2 (BLUE) audio jack.

Alarm Detection Wiring

The MBU provides an external alarm detection input, which can be used to transmit notification to extensions when the external switch is closed or opened (programmable through Admin Programming). This alarm detection input is provided throug h MJ2-1 pin 3-4 of the MBU.

SBX IP Installation Guide

Cable Wiring 5-9

Release 3.5

June 2010

Chapter 5: Terminal Connection and Wiring Method

Cable Wiring

Wall Mount Wiring

To install wall mount wiring, perform the following steps:

1. Make sure that the BKSU and EKSU have been installed correctly (see Chapter 3

- KSU Installation).

2. Connect cables to CO/STA and MOH/RS-232C ports, as sho wn in Figure 5-8

3. Conn e ct the po wer cor d an d the ba tte r y cab l e.

4. Remove plastic filter pieces.

5. Using the tie cable provided, tie all the cables and the power cord (as appropriate) through the tie slot at the bottom-right side of the KSUs.

6. Close the cove rs of the KSUs, then close the cord cover.

Figure 5-8 Wall Mount Wiring

SBX IP Installation Guide

Cable Wiring 5-10

Release 3.5

June 2010

Chapter 5: Terminal Connection and Wiring Method

Rack Mount Wiring

1. Check that the BKSU and EKSU have been installed correctly (see Chapter 3 -

KSU Installation).

2. Connect cables to the CO/STA and MOH/RS-232C ports, as shown in Figure 5-9

3. Connect the power cord and the battery cable.

4. Remove the plastic filter pieces.

5. Using the tie cable provided, tie all the cables and the power cord (as appropriate) through the tie slot at the bottom-right side of the KSUs.

6. Close the covers of the KSUs and close the cord cover.

Figure 5-9 Rack Mount Wiring

SBX IP Installation Guide

IP Phones on the SBX IP 5-11

Release 3.5

June 2010

Chapter 5: Terminal Connection and Wiring Method

IP Phones on the SBX IP

Supported IP phones:

• IP7008D, IP7024D, IP7024LD

• Nomad IP (Wireless)

• Nomad SP (Soft Phone)

NOTE: This section specifically applies to setting up the IP7000-series telephones only.

Minimum requirements

System

• SBX IP system with VoIP card

• Static IP address for VoIP card. If NAT is used, it must be a 1-to-1 NAT

• Separate IP address for the KSU's LAN port for system administration

NOTE: No VoIP communication takes place on the KSU LAN port.

• KSU version 1.0Cf

• VoIP card software version B.1Dq.

Installed Environment

• CAT5E (or higher) patc h cords from VoIP card to LAN switch

• No hubs

• Adequate bandwidth for the anticipated number of H.323 VoIP calls

SBX IP Installation Guide

IP Phones on the SBX IP 5-12

Release 3.5

June 2010

Chapter 5: Terminal Connection and Wiring Method

IP endpoint licensing

Nomad SP requires a per-seat license. Two seats are automatically included; you do not have to install activation codes for these two seats.

IP7000 series and NomadIP wireless phones do not require a license.

NOTE: Entering IP address information to the KSU database from a digital phone is

performed differently from programming IP setting s for an IP remote phone.

Digital stations on KSU: Enter digits in groups of 3, with no punctuation or decimal.

Example: To program the address 192.168.1.3, dial 192168001001

IP phone: Enter digits with an asterisk [*] as the decimal.

Example: To program the address 192.168.1.10, dial 192*168*1*10

IP Addressing

To begin, obtain IP addresses from the network administrator for the location in which you are setting up the SBX IP system. Note them in the table provided below for reference while programming the system:

Table 5-3 IP Addresses for current system

VoIP card (VoIB) KSU LAN port IP Phone

IP Address

Subnet Mask

Default Gateway

SBX IP Installation Guide

(may be DHCP)

Your PC

(may be DHCP)

IP Phones on the SBX IP 5-13

Release 3.5

June 2010

Chapter 5: Terminal Connection and Wiring Method

Figure 5-10 System Setup

• You will also need a 24-button SBX digital telephone to set up the system.

• For a typical test-bench or demonstration setup, you need 4 conne ctions to a LAN

switch, each via a straight-through CAT5E patch cord as shown in Figure 5-10

• You may use the IP address information shown in Table 5-4

to set up a closed

demo of the IP phone.

NOTE: These addresses will not function in a wide-area network or the Internet. They

are for testing and demonstration purposes only:

Table 5-4 IP Addresses for testing and demonstration only

VoIP card KSU LAN port IP Ph on e Your PC

IP Address 192.168.1.4 192.168.1.3 192.168.1.5 192.168.1.2 Subnet Mask 255.255.255.0 2 55.255.255.0 255.255.255.0 255.255.255.0 Default Gateway 192.168.1.1 192.168.1.1 192.168.1.1 192.168.1.1

SBX IP Installation Guide

IP Phones on the SBX IP 5-14

Release 3.5

June 2010

Chapter 5: Terminal Connection and Wiring Method

Preparation

1. Before starting, verify that the VoIP (VoIB) card is installed into the system properly (see page 4-18

), and that the card is recognized in the KSU database.

2. KSU DIP switches must be set to enable the system to retain programming changes.

3. Set the PC IP address, default gateway, and subnet mask as noted in Table 5-3

4. Set the KSU's IP addressing using PGM 108 when logged into KSU administration from the 24-button digital attendant st ation ( Station 100 by default). This assigns the IP address to the KSU's LAN po rt. The configura tion for the VoIP card begins here.

PCAdmin Connection

Follow the PCAdmin User's Guide or the Tech Tip regarding setting up PCAdmin to establish connection between the SBX system and PCAdmin. Remember, when connecting to the SBX IP using a LAN switch, a straight-through patch cable (not a crossover cable) is required.

Configuring The VoIP Card Using PCAdmin

NOTE: Digital phone-based programming is shown on page 5-22.

1. Double-click Pre-programmed > Configuration

SBX IP Installation Guide

IP Phones on the SBX IP 5-15

Release 3.5

June 2010

Chapter 5: Terminal Connection and Wiring Method

2. Right-click on the VoIB, then select Logical Assignment.

3. In Logical Assignments, right-click VoIB and Select (Virtual VoIB) => Append to

Station. A notation of 99 will be entered in the STA Board field.

4. Click Update.

5. In VoIB Gateway > VoIB Gatekeeper Settings enter the IP Address, Default

Gateway, and Subnet Mask that you are assigning to the VoIP card per the worksheet.

SBX IP Installation Guide

IP Phones on the SBX IP 5-16

Release 3.5

June 2010

Chapter 5: Terminal Connection and Wiring Method

6. Click Update.

7. In RSG IP Programming, double-click VoIB Slot for RSG/IP.

8. Select the VoIB card (10), then click the > button to move the selection to the right-hand column.

You will see the card slot on the right side.

SBX IP Installation Guide

IP Phones on the SBX IP 5-17

Release 3.5

June 2010

Chapter 5: Terminal Connection and Wiring Method

9. Click Update.

10. Select the card from the VoIB Slot dropdown.

11. Select 2 for the number of channels to be used for IP Phones from the Channel

Number dropdown.

12. Click Update Channel.

13. Select the 2 from the IP Phone Number dropdown, then click Update Num.

This tells the system to assign 2 IP stations.

SBX IP Installation Guide

IP Phones on the SBX IP 5-18

Release 3.5

June 2010

Chapter 5: Terminal Connection and Wiring Method

14. Click Update.

15. Reset the KSUDouble-click RSG/IP Programming > IP Phone Attributes.

16. Double-click on bin 1 (row 1).

SBX IP Installation Guide

IP Phones on the SBX IP 5-19

Release 3.5

June 2010

Chapter 5: Terminal Connection and Wiring Method

17. Enter the MAC address which you will find labeled on the bottom of the IP phone,

then click Update.

NOTE: Be sure to include the colons in the MAC address.

You do not need to program the other data values in PGM 386 for IP7000 remote phones. The ID and Password values will be used when you are configuring a Nomad SP (Soft Phone).

SBX IP Installation Guide

IP Phones on the SBX IP 5-20

Release 3.5

June 2010

Chapter 5: Terminal Connection and Wiring Method

Configuring IP phone settings

To verify connectivity to the VoIP card, you should ping the VoIP card from where the phone is located.

Setting up the IP Phone will vary depending upon the network infrastructure, IP Address schema, and location of the system. You need the following information to properly configure the IP Phone:

• The IP Address of the VoIP card.

• Whether the IP Address information is supplied dynamically (DHCP) or statically

• An IP Address and Subnet Mask for the IP Phone (either static or DHCP).

• The Default Gateway IP Address (either static or DHCP).

NOTE: If IP Addresses are static, you will need to obtain the correct IP Address,

Subnet Mask, and Default Gateway information from the IT Administrato r.

Connect the IP Phone to the local network. It can be powered with an AC power adapter or a port on a POE (Power Over Ethernet) switch. The power adaptor is part #6899-PS. When powered, the IP Phone completes its boot sequence, th en attemp ts to connect to the VoIP Card. If the phone is unable to connect to the V oIP card, the following message is displayed:

NO RESPONSE FROM MFIM SET [*] - RESTART [#]

1. Press * to begin configuring the phone.

2. Use the Volume + and - to navigate the settings.

3. Enter information as follows:

• If you are prompted for a password: Dial 147*

• At MODE[R/L] ? (This is the Remote/Local Setting). All IP Phones are

considered remote to the SBX IP no matter where they are physically or logically. Set the mode to REMOTE. Press # until the display shows:

MODE[R/L] ? [REMOTE] - CHANGE[#]

4. Press Hold/Save to store the setting as REMOTE.

5. Press the Volume + until DHCP ? appears.

NOTE: If IP Addressing is assigned via DHCP, this should be enabled.

If IP Addressing is Static, this should be disabled.

SBX IP Installation Guide

IP Phones on the SBX IP 5-21

Release 3.5

June 2010

Chapter 5: Terminal Connection and Wiring Method

6. Press # until the display shows the correct state.

7. Press Hold/Save to retain the entry.

8. Press the Volume + until MFIM IP ADDRESS (DOT:*) appears. This is the VoIB IP

Address Field. MFIM = VoIB. Enter the IP Address on the dial pad. Press the * to enter a “.” (dot). For example, to enter 192.168.1.10, dial 192*168*1*10. Press Hold/Save to retain the entry.

MFIM IP ADDRESS(DOT:*) xxx.xxx.xxx.xxx (The VoIB IP Address)

9. Press the Volume + until ROUTER IP ADDRESS(DOT:*) appears. This is the

Default Gateway IP Address Field. If IP Addressing is being assigned, you won't need to program this field. If IP Addressing is statically assigned, enter th e IP Address of the Default Gateway and press Hold/Save.

ROUTER IP ADDRESS(DOT:*) xxx.xxx.xxx.xxx (Default Gateway IP Address)

10. Press the Volume + until PHONE NET MASK(DOT:*) appears. This is the Subnet

Mask associated with the IP Address of the phone. If IP Addressing is being dynamically assigned, you won't need to program this field. If IP Addressing is statically assigned, enter the IP Address of the Default Gateway and press Hold/Save.

PHONE NET MASK(DOT:*) xxx.xxx.xxx.xxx (Subnet Mask)

11. Press the Volume + until PHONE IP ADDRESS(DOT:*) appears. This is the

station IP Address Field. If IP Addressing is being dynamically assigned, you won't need to program this field. If IP Addressing is statically assign ed , ente r th e IP Address of the station and press Hold/Save.

PHONE IP ASSIGNED(DOT:*) xxx.xxx.xxx.xxx (Station IP Address)

12. When these fields have been completed, press the Speaker button to reboot the

IP Phone. The phone will contact the VoIP card and register to the system. It receives its station number assignment from the KSU.

SBX IP Installation Guide

IP Phones on the SBX IP 5-22

Release 3.5

June 2010

Chapter 5: Terminal Connection and Wiring Method

In this example, the IP address and station number information appears after two IP phones have registered to the system:

13. Test the IP phone by dialing an extension number.

Programming VoIP card settings from a digital station

This is an alternative to PCAdmin programming (shown in the preceding section). Disregard this section if you have configured the IP phone using PCAdmin.

1. Enter KSU programming from the digital attendant phone.

2. Press PGM.

3. Dial 103 (Logical Slot Assign).

4. Press Flex Button 2 (STA).

5. What to enter will depend on what cards are installed. If there are two 3x8

Expansion cards installed the display will show 01 02 .. .. ..

Dial 01 02 99 to assign station ports to the VoIB.

6. Click Save.

SBX IP Installation Guide

IP Phones on the SBX IP 5-23

Release 3.5

June 2010

Chapter 5: Terminal Connection and Wiring Method

Assign IP Address to the VoIB

1. Press PGM.

2. Dial 340 (VoIB Attributes).

3. Press Flex Button 1 (IP ADDR).

4. Dial the IP Address (e.g., 192.168.1.10 Dial 192168010010).

5. Click Save.

6. Press Flex Button 2 (Gateway ADDR) - Mandatory.

7. Dial the default Gateway for the VoIB (ex: for 192.168.1.1 dial 192168001001).

8. Click Save.

9. Press Flex Button 3 (Subnet Mask).

10. Dial the Subnet Mask (ex: for 255.255.255.0 dial 255255255000).

11. Click Save.

VoIB Slot/Port Usage Assignment

1. Press PGM.

2. Dial 380 (VoIB Slot Assignment).

3. Press Flex Button (VoIB Slot).

4. Dial 10 (Slot Number to Program).

5. Click Save.

6. Press Flex button 2 (RSG/IP channel Assign).

7. Dial 10 (Slot Number).

8. Dial 4 (or number of channels to reserve for IP Phones).

9. Click Save.

VoIB IP Station Assignment

1. Press PGM.

2. Dial 381 (RSG/IP No Assign).

3. Press Flex Button 2.

4. Dial the number of IP stations you wish to program (e.g., 04).

5. Click Save.

6. Reset the system and VoIP card.

SBX IP Installation Guide

IP Phones on the SBX IP 5-24

Release 3.5

June 2010

Chapter 5: Terminal Connection and Wiring Method

Program IP Phone Attributes - The number of bins available to program will correspond to the number of IP phones programmed in PGM 381.

1. Press PGM.

2. Dial 386 (IP Phone Attrib).

3. Dial the Bin Number (for example, 01 This would be the first IP station).

4. Press Flex Button 1.

5. Dial the MAC Address of the IP Phone.

NOTE: * = A, # = B, NAV Left = C, NAV Right = D, NAV Up = E, NAV Down = F

6. Click Save.

SBX IP Installation Guide

Chapter 6

Release 3.5

June 2010

Starting the SBX IP System

Before Starting the SBX IP System

In preparation for programming, perform the following steps:

1. Turn the DIP switch (SW2) ON prior to installing the MBU, to protect the system

data in case of power failure.

2. Check that the DIP switch (SW1) of the MBU is set to All ON.

3. Plug the AC power cord into the SBX IP system and AC outlet.

4. Program the Nation Code (PGM 100) as applicable.

5. Reset the SBX IP system.

6. Set the 4th pole (SW1) of the MBU to OFF when the system operates normally, to

protect programmed features after system power-up and initialization.

SBX IP Installation Guide

Basic Programming 6-2

Release 3.5

June 2010

Chapter 6: Starting the SBX IP System

Basic Programming

The SBX IP system can be programmed to meet individual needs. There are two ways to perform Admin Programming:

• PC Admin - Refer to the PC Admin Programming Manual.

• DKT - In this manual, DKT (Station 100) Admin Programming is described.

DKT Programming

All programming is done at one station (S tation 100, S tation Po rt #00, by default) using the 7224D Digital Key Telephone.

Additional programming stations may be assigned (PGM 113 - FLEX 1), but only one DKT can be active in the programming mode at any one time.

NOTE: All programming must be performed from a 24-button phone or the PCAdmin

software program.

When in programming mode, S tation 10 0 does not operate as a nor mal telephone, but instead works as a programming instrument with all the buttons redefined as follows:

• Dial Pad Keys - used to enter numerical information in the various data fields.

• Flexible Buttons (the 24 buttons located on the right side of the phone) - used to indicate a specific data field and to enter information.

• Soft Buttons (BACK / DELETE / SAVE) - used to go back / delete data / save data input.

SBX IP Installation Guide

Basic Programming 6-3

4 5

6 7

11 12

15 16

Release 3.5

June 2010

Chapter 6: Starting the SBX IP System

Button Explanation

The following graphic and its associated table describe the button s and function keys. (Refer to the IP7208D/IP7024D User Guide for detailed information and operation instructions.)

SBX IP Installation Guide

Basic Programming 6-4

Release 3.5

June 2010

Chapter 6: Starting the SBX IP System

IP7224D Keyset - Basic Features

1 Handset Used for handse t call . 2 Headphone When using a headphone, toggles the headphone state. 3 Speaker When in speaker mode, used to listen to a caller in a handsfree mode. 4 Speed Used to access speed dialing, save number redial, and last number redial.

The button is also used to access flexible button programming.

5 DND The Do Not Disturb feature lets you activate a “do not ring this phone” mode.

When DND is active, this button is red.

6 Speaker Button Toggles speakerphone state between speaker mode and handset mode. The

button is red when speakerphone is active.

7 Hold/Save Puts a call on hold or saves the PGM. 8 3 Soft Buttons Used to work in conjunction with fixed and flexible features. 9 LCD Display Displays phone status information, dialing directories, and test message

information.

10 Ring LED Illuminates when the phone is ringing. 11 Trans/PGM Used to set up a conference call or transfer a call. 12 Flexible The remaining XX Flex buttons can be assigned a feature. 13 Call back A station can initiate a call back request to another busy station. Once that

station becomes idle, the station that left the call back request is signaled.

14 Volume Adjusts the audio level. 15 MIC When in speaker mode, used to speak to a caller in a handsfree mode. 16 Menu Used to move to the desired option (Dial, MSG, Program) and for arrows key. 17 Phone Book Use to save a phone number and to make calls with saved information.

SBX IP Installation Guide

Basic Programming 6-5

Release 3.5

June 2010

Chapter 6: Starting the SBX IP System

Entering the Programming Mode

To enter programming mode, perform the following steps:

1. Lift the handset or press the speaker button on the Admin station. ICM dial tone

will sound.

2. Press the [TRANS/PGM] button and dial * #. A confirmation tone will sound.

3. Enter the Admin password, if a password has been set; a confirmation tone

sounds indicating that the station is in Admin Programming mode .

4. Access each program by pressing the [TRANS/PGM] button. The following will

initially display:

ENTER PGM NUMBER

5. Dial the desired three-digit program number. If an error is made while entering

data, the [TRANS/PGM] button will return to the previous status.

NOTE: To return to the previous state while in Admin Programming, press the [BACK] soft button (this

clears the temporary data fields).

Permanent Update Procedure

To accept changes while programming, perform the following steps:

1. Press the [HOLD/SAVE] button when all changes have been entered to store the

data permanently.

2. If all data was entered correctly, a confirmation tone will sound when pressing the

[HOLD/SAVE] button. If there were any errors in the entering of data, an error tone will sound and data will not be stored in the permanent memory.

Resetting the System

To reset the system, perform the following:

Enter [PGM] + 450, then [FLEX] +15, then press the [HOLD/SA VE] button.

SBX IP Installation Guide

Basic Programming 6-6

. – 13 Q – 11 Z – 12 1 – 10

A – 21 B – 22 C – 23 2 – 20

D – 31 E – 32 F – 33 3 – 30

G – 41 H – 42 I – 43 4 – 40

J – 51 K – 52 L – 53 5 – 50

M – 61 N – 62 O – 63 6 – 60

P – 71 Q – 72 R – 73 S – 74 7 – 70

T – 81 U – 82 V – 83 8 – 80

W– 91 X – 92 Y – 93 Z – 94 9 – 90

Blank – ½1 : – ½2 , – ½3

0 – 00

Release 3.5

June 2010

Chapter 6: Starting the SBX IP System

Pre-Programming

Location PGM - Nation Code and Site Name (PGM 100)

NOTE: To modify Nation Code, the 4th po le of the DIP switch (SW1) on the MBU must

be turned ON.

NOTE: SBX IP supports only English language and prompts.

Nation Code

To program the Nation Code, perform the following steps:

1. Press the [TRANS/PGM] button + PGM number (100), then [FLEX1] + 1 [Nation Code for United States].

2. Press the [HOLD/SAVE] button to accept the change.

3. Reset the SBX IP to initialize the Database for Nation.

4. Set the 4th pole (SW1) of the MBU OFF, to protect programmed features.

Site Name

1. Press the [TRANS/PGM] button + Enter Site Name (use the following DKT Map, Max. 23 characters allowed), then press [FLEX 2].

2. Press the [HOLD/SAVE] button to accept the change.

SBX IP Installation Guide

Basic Programming 6-7

Release 3.5

June 2010

Chapter 6: Starting the SBX IP System

NATION CODE TABLE

Nation Code Nation Code Nation Code

Argentina 54 Greece 30 Nigeria 234 Australia 61 Guam 671 Norway 47 Bahrain 973 Guatemala 502 Oman 968 Bangladesh 880 Guyana 592 P.N.G. 675

Belgium 32 Haiti 509 Pakistan 92 Bolivia 591 Honduras 504 Panama 507 Brazil 55 Hong Kong 852 Paraguay 595 Brunei 673 India 91 Peru 51

Burma 95 Indonesia 62 Philippines 63 Cameroon 237 Iran 98 Portugal 351 Canada + USA 1 Iraq 964 Qutar 974 Chile 56 Ireland 353 Saudi Arabia 966 China (Taiwan) 886 Israel 972 Senegal 221 CIS 7 Italy 39 Singapore 65 Columbia 57 Japan 81 South Africa 27 Costa Rica 506 Jordan 962 Spain 34 Cyprus 357 Kenya 254 Sri Lanka 94 Czech 42 Korea 82 Swaziland 268 Denmark 45 Kuwait 965 Sweden 46 Ecuador 593 Liberia 231 Switzerland 41 Egypt 20 Libya 218 Thailand 66 El Salvador 503 Luxembourg 352 Tunisia 216 Ethiopia 251 Malaysia 60 Turkey 90 Fiji 679 Malta 356 U.A.E. 971 Finland 358 Mexico 52 United Kingdom 44 France 33 Monaco 377 United States 1 Gabon 241 Morocco 212 Uruguay 598 Germany 49 Netherlands 31 Venezuela 58 Ghana 233 New Zealand 64 Y.A.R. 967

SBX IP Installation Guide

Basic Programming 6-8

Release 3.5

June 2010

Chapter 6: Starting the SBX IP System

Board Assignment (PGM 101)

To use a CO line, an extension line, and a board, ensure that the code of these boards are registered on the system at PGM 101.

When registering a board, if the fourth pole of switch bank one (SW1) of the MBU is ON, the board is automatically registered into the system database.

After registering a new board to the syste m, place th e fourth pole of (SW1) in the OFF position and perform a system reset.

While in the Admin programming mode:

1. Press the [TRANS/PGM] button + PGM number (101).

2. Enter slot nu m be r (2 digits).

3. Press [FLEX1] button.

4. Enter Board Type code (2 digits).

5. Press the [HOLD/SAVE] button to accept the change.

Table 6-1 Board ID

STA CODE COL CODE ETC CODE

HYBRID 17 VoIB 41 VMIB 64

Table 6-2 Slot Definition

SLOT NUMBER SLOT POSITION KINDS OF BOARDS

01 Hybrid on BKSU HYBRID 02 Optional extension board on BKSU HYBRID 03 Hybrid port on EKSU HYBRID 04 Optional extension board on EKSU HYBRID 05 LCOB on BKSU -06 T1 / PRI -07 LCOB on EKSU -08 Optional LCOB on EKSU -09 VMIB on BKSU VMIB 10 VoIB on BKSU VoIB

SBX IP Installation Guide

Basic Programming 6-9

Release 3.5

June 2010

Chapter 6: Starting the SBX IP System

Figure 6-1 Slot Locations

Logical Slot Assignment (PGM 103)

If the assignment of each board is at the end, it is automatically registered by slot number order. You can reassign the slot order of each CO Line or extension line as appropriate to your circumstance.

COL Board

1. Press the [TRANS/PGM] button + PGM number (103).

2. Press [FLEX1] button.

3. Enter logical slot number (CO board slot: 05, 06, 07, 08, 10).

4. Press [HOLD/SAVE] button to accept change.

STA Board

1. Press the [TRANS/PGM] button + PGM number (103).

2. Press the [FLEX 2] button.

3. Enter logical slot number (STA board slot: 01-04).

4. Press the [HOLD/SAVE] button to accept the change.

SBX IP Installation Guide

Basic Programming 6-10

Release 3.5

June 2010

Chapter 6: Starting the SBX IP System

VMIB Board

1. Press the [TRANS/PGM] button + PGM number (103).

2. Press the [FLEX 3] button.

3. Enter logical slot number (VMIB Slot: 09).

4. Press the [HOLD/SAVE] button to accept the change.

Numbering Plan Type (PGM 104)

To program the Numbering Plan Type, perform the following:

1. Press the [TRANS/PGM] button + 104.

2. Enter the Numbering Plan Type (1 digit, refer to the following table).

3. Press the [HOLD/SAVE] button to accept changes.

Table 6-3 Slot Definition

NUMBER SET

TYPE/ PRESS #

01 100-147 Yes As the basic type, the 1st digit of the

02 100-147 No The station number can be changed

03 100-147 No 04 700-747 No 05 200-247 No 06 21-68 No 07 100-147 No 08 100-147 No The station number can be changed

INTERCOM RANGE DEFAULT REMARK

station number should be 1-4

up to 799

up to 999

SBX IP Installation Guide

Basic Programming 6-11

Release 3.5

June 2010

Chapter 6: Starting the SBX IP System

Flexible Numbering Plan (PGM 105)

To set the Flexible Numbering Plan, perform the following steps:

1. Press the [TRANS/PGM] button + 105.

2. Enter the station range (dial the St a rt a nd End n umb ers as de scr ibe d in the table).

3. Press the [HOLD/SAVE] button to accept the changes.

Table 6-4 Numbering Plan Detail

STATION NUMBERS DESCRIPTION

000 001 002 003 [ TRANS/PGM] + 105 100 101 102 103 000 001 002 003 Station Number Assign-Four station numbers correspond to 100 101 102 103

the four (4) port numbers. The station number length is in the range of two (2) digits through four (4) digits. There are two methods for changing the station number:

Dial two station numbers - Dial the range of the start and end station numbers. The LCD will show the dialed range value. Press the [HOLD/SAVE] button to accept the change. All LEDs of BTNs will be extinguished.

Press one of FLEX 1-4 - Each FLEX button (1-4) is assigned to a corresponding station number (1- 4) on the current LCD. The LED of the pressed Flexible button will show steady light. Dial the new station number and press the [HOLD/SAVE] button to accept change, or press another Flexible button to assign a station number to other stations without saving.

To chang e the next four (4) station numbers then press [ button. If you want to change previous four (4) station numbers, then press [

V] button.

To delete all station numbers, press the [SPEED] button and press the [HOLD/SAVE] button; all station numbers will be

cleared. 000 001 002 003 Press the [HOLD/SAVE] button to save changes to the 100 400 102 103

database permanently (Ex: Press FLEX 2, dial 400 and

press [HOLD/SAVE] button).

SBX IP Installation Guide

Basic Programming 6-12

Release 3.5

June 2010

Chapter 6: Starting the SBX IP System

Flexible Numbering Plan (PGM 106-107, & 109)

To program Flexible Numbering using PGM 106, perform the following steps:

1. Press the [TRANS/PGM] button + 106.

2. Enter the desired code (refer to the following table).

3. Press the [HOLD/SAVE] button to accept changes.

Table 6-5 Flexible Numbering Plan (PGM 106)

FLEX ITEM DEFAULT VALUE

1 Station Group Pilot Number Range 620-629 2 Internal Page Zone Number Range 501-510 3 Internal All Call Page 543 4 Meet Me Page 544 5 External Page Zone 545 6 All Call Page (Internal/External) 549 7 SMDR Acco unt Code 550 8 Flash Comman d to CO Line 551

9 Last Number Redial (LNR) 552 10 Do-Not-Disturb 553 11 Call Forward 554 12 Speed Dial Program 555 13 MSG Wait/Call-Back Enable 556 14 MSG Wait/Call Back Answer 557 15 Speed Dial Access 558 16 Cancel DND/CFW/Pre-Selected MSG Features 559 17 SLT Hold 560 18 Reserved N/A 19 Reserved N/A 20 SLT Program Mode Select 563 21 ACD Reroute 564

SBX IP Installation Guide

Basic Programming 6-13

Release 3.5

June 2010

Chapter 6: Starting the SBX IP System

To program Flexible numbering using PGM 107, perform the following steps:

1. Press the [TRANS/PGM] button + 107.

2. Enter the desired code (refer to the following table).

3. Press the [HOLD/SAVE] button to accept the changes.

Table 6-6 Flexible Numbering Plan (PGM 107)

FLEX ITEM DEFAULT VALUE

1 Alarm Reset 565 2 Group Call Pickup 566 3 UCD Group DND 568 4 Night Answer 569 5 Call Park Location Range 601-610 6 Direct Call Pick-Up 7 7 Access CO Line Group 801-824

(8 + CO Group Line Number) 8 Access Individual CO Line 88 (88 + CO Line Number) 9 Reserved N/A

10 Access Held CO Line Group 8*

11 Access Held Individual CO Line 8# (8# + CO Line Number)

12 Access to CO Line in the 1st Available CO Line

Group 13 Attendant Call 0 14 Door Open - 1 #*1 15 Door Open - 2 #*2 16 Door Open - 3 #*3 17 Door Open - 4 #*4 18 VM MSG Wait Enable *8 19 VM MSG Wait Cancel *9

SBX IP Installation Guide

Basic Programming 6-14

Release 3.5

June 2010

Chapter 6: Starting the SBX IP System

To program Flexible numbering using PGM 109, perform the following steps:

1. Press the [TRANS/PGM] button + 109.

2. Enter the desired code (refer to Table).

3. Press the [HOLD/SAVE] button to accept changes.

Table 6-7 Flexible Numbering Plan (PGM 109)

FLEX ITEM DEFAULT VALUE

1 Reserved n/a 2 Reserved n/a 3 Reserved n/a 4 Conference Room 57 5 SLT Conference Page Join 58 6 Unsupervised Conf Timer Extend ## 7 Remote Mobile Extension (MEX) Number #1

System IP Setup (PGM 108)

To set up IP functionality, perform the following. Use the # key to skip to the next menu item, as needed.

IP Name

1. Press the [TRANS/PGM] button + 108.

2. Press the F LEX 1 bu tt on .

3. Enter the desired IP Name (up to 15 characters).

Other Codes

1 = 10 6 = 60 Space = 61

2 = 20 7 = 70 , =

3 = 30 8 = 80 : =

4 = 40 9 = 90 . = 13

5 = 50 0 = 00

6 = 06

4. Press the [HOLD/SAVE] button to accept the changes.

SBX IP Installation Guide

Basic Programming 6-15

Release 3.5

June 2010

Chapter 6: Starting the SBX IP System

Server IP Address

1. Press the [TRANS/PGM] button + 108.

2. Press the F LEX 2 bu tt on .

3. Enter the server IP Address (12 digits). (for example, 192168131154 for

192.168.131.154)

4. Press the [HOLD/SAVE] button to accept changes.

CLI IP Address

1. Press the [TRANS/PGM] button + 108.

2. Press the FLEX 3 Button.

3. Enter the CLI IP Address (12 digits).

4. Press the [HOLD/SAVE] button to accept the changes.

Gateway Address

1. Press the [TRANS/PGM] button + 108.

2. Press the FLEX4 button.

3. Enter the Gateway Address (12 digits).

4. Press the [HOLD/SAVE] button to accept changes.

Subnet Mask Address

1. Press the [TRANS/PGM] button + 108.

2. Press the FLEX5 button.

3. Enter the Subnet Mask (12 digits).

4. Press the [HOLD/SAVE] button to accept changes.

SBX IP Installation Guide

BLF Manager 6-16

Release 3.5

June 2010

Chapter 6: Starting the SBX IP System

BLF Manager

BLF Manager is an optional Windows software program that can be used to manage Busy Lamp Field (BLF) updates for systems networked over VoIP.

BLF Manager must be installed to one system in the reachable over IP by all SBX KSUs.

BLF Manager software is not required for VoIP networking. It is only necessary if DSS/BLF updates on stations and DSS console are desired.

There is no need for BLF Manager software unless you have networked systems.

BLF Manager Installation

Requirements

OS: Windows 95 or above CPU: Pentium 500Mhz or above Memory: 128M or more (256M recommended) HDD: More than 30MB of free space

Installation

Make a directory and copy "BLFManager.exe" to it.

Automatic running

T o run BLF Man ager automatically , put a shortcut link to BLFManager .exe into "St artup programs".

SBX IP network and must be

Uninstallation

To remove BLF Manager from the server PC, delete the installation directory.

SBX IP Installation Guide

Vertical Vertical - MBX IP - (donated by Ray from - Vertical) Vertical SBX - IP Installation Guide 3.5

Specifications and Main Features

Frequently Asked Questions

User Manual

REVISION HISTORY

Contents

Important Safety Instructions

Safety Requirements

Precautions

Cautions

Disposal of Old Units

Using this Manual

SBX IP System Highlights

Supported phones

System Connection Diagram

System Components

Basic KSU (p/n 4000-00)

Expansion KSU (p/n 4002-00)

System Specification Tables

Board Capacities

System Capacities

Dialing Specifications

Dimensions and Weight

Environmental Specifications

Electrical Specifications

Pre-Installation

Safety Installation Instructions

Installation Precautions

Wiring Precautions

KSU Installation

Unpacking

KSU Exterior and Dimension

Opening and Closing the Front Cover

Frame Ground Connection

External Backup Battery Installation

KSU Mounting

Expansion KSU Installation

Unpacking

Connecting the Expansion KSU to the Basic KSU

Expansion KSU Mounting

Basic Board Installations

Main Board Unit (p/n: 4000-00)

Main Board Unit (p/n: 4000-03)

Modular Jack (MJ1 - MJ3) Pin Assignment

Switch, LED, and Connector

SBX 25-Pair Installation Cable Pinouts

Expansion Main Board Unit (EMBU)

Expansion MBU (p/n: 4002-00)

Expansion MBU (p/n: 4002-03)

Modular Jack (MJ1 - MJ3) Pin Assignment

CO Line and Extension Boards

3x8 Expansion Board (3 CO Line and 8 Hybrid)

3x16 Expansion Board (3 CO Line and 16 Digital)

Other Board Installations (optional)

Digital Telephone Interface Board (DTIB16)

Modem Function Unit (MODU)

T1/PRI Interface Board

VoIB -- Voice Over Internet Protocol Board (4ch)

Voice Mail Interface Board (VMIB)

Terminal and Doorbox Models

Terminal Cabling Distance

Basic Terminal Connection

DKT and DSS

Doorbox

Connecting Additional Terminals

External Music Source Wiring

Relay Contacts

External Paging Port Wiring

Alarm Detection Wiring

Cable Wiring

Wall Mount Wiring

Rack Mount Wiring

IP Phones on the SBX IP

Supported IP phones:

Minimum requirements

IP endpoint licensing

IP Addressing

Preparation

PCAdmin Connection

Configuring IP phone settings