Veris V400 Installation Instructions

REL AY S

HAZARD OF ELECTRIC SHOCK, EXPLOSION, OR ARC FLASH

• Follow safe electrical work practices.

See NFPA 70E in the USA, or applicable local codes.

• This equipment must only be installed and serviced by qualied electrical personnel.

• Read, understand and follow the instructions before installing this product.

• Turn o all power supplying equipment before working on or inside the equipment.

• Use a properly rated voltage sensing device to conrm power is o. DO NOT DEPEND ON THIS PRODUCT FOR VOLTAGE INDICATION

Failure to follow these instructions will result in death or serious injury.

DANGER

INSTALLATION GUIDE

V400

10A DPDT Enclosed Relay

Installer’s Speciﬁcations

Operating Temperature -34°C to 60°C (-29 ° to 140°F) Operating Humidity 10-90% non condensing Expected Relay Life Electrical (at rated current): 100,000 cycles Mechanical (unpowered): 10,000,000 cycles Relay Status LED ON=energized

Wire Specications:

Lead Length 14” (356mm) min. Gauge UL1015; Coil: 18AWG; Contacts: 16AWG Insulation Class 600VAC RMS Agency Approvals UL508 enclosed device listing, pollution degree 2

INSTALLATION

Disconnect and lock out all power sources before beginning the installation.

1. Using the threaded nipple, connect the relay to the desired enclosure through a knock out hole.

2. Secure with the conduit nut provided.

3. Connect coil:

• Choose the coil common lead (white with yellow stripe) and connect it to the common (-) source termination point.

NOTICE

• This product is not intended for life or safety applications.

• Do not install this product in hazardous or classiﬁed locations.

• The installer is responsible for conformance to all applicable codes.

• Mount this product inside a suitable ﬁre and electrical enclosure.

DIMENSIONS

2.9"

(74 mm)

2.8"

(71 mm)

1.6"

(41 mm)

• Choose either the low voltage (10-30VAC/DC, white with blue stripe) or high voltage (208-277VAC, white with brown stripe) lead, depending on the application requirements, and connect it to the (+) source termination point.*

4. Connect relay contacts:

• Choose the relay common wire (yellow) and connect to the switched load.

• Choose the relay N.O. (orange) and/or* N.C. (blue) lead and connect to the

switched load.

• Repeat with violet, brown, and grey wires, respectively, for the second set of contacts

5. Secure the enclosure and reconnect power.

* Isolate or insulate all non-terminated wires according to local electrical code requirements, i.e. wire nut.

1.7"

Alta Labs, Enercep t, Enspector, Hawkeye, Trustat, Veris, and the Veris ‘ V’ logo are trademark s or registered tradema rks of Veris Industries, L.L .C. in the USA and /or other count ries.

1/2" NPT Nipple

(43 mm)

1.8"

(46 mm)

V400

*Contact ratings are for single pole operation. When operating both poles simultaneousley, the total load cannot exceed the ratings above.

Pull in Voltage AC DC

20-30V..................................... 18 20

208-277V................................. 186

Drop Out Voltage AC DC

20-30V..................................... 4 5

208-277V................................. 44

Voltage Coil Current AC DC

24V.......................................... 43mA 25mA

30V.......................................... 54mA 31mA

208V........................................ 27mA -

277V........................................ 36mA -

TYPICAL COIL PERFORMANCE

CONTACT RATINGS*

Resistive.............. 10A@277VAC, 30VDC

Motor.................... 120VAC, 1/8HP

N.C.

Common

20-30VAC/DC

LOW

wht/blue

COMM

wht/yellow

Common

N.O.

CONTACT OUTPUTCONTROL SYSTEM INPUT

White

YELLOW

White

ORANGE

N.C.

Common

N.O.

208-277VAC

wht/brown

White

INSTALLATION GUIDE

WIRING COLOR CODES

CONTACT AND COIL SPECIFICATIONS

WIRING EXAMPLE

Nipple mount directly to a panel

To Load A

N.C.

N.O.

To Load B

COM

To Power

To Controls

Nipple mount to a 2x or 4x electrical box

To Load B

To Power

CONTROL

PANEL

COIL

To Load A

CONTACTS

N.C.

Wire Nuts

N.O.

COM

Alta Labs, Enercep t, Enspector, Hawkeye, Trustat, Veris, and the Veris ‘ V’ logo are trademark s or registered tradema rks of Veris Industries, L.L .C. in the USA and /or other count ries.

To Control

* Isolate any unused wires, e.g. wire nut.