Veris V222 Installation Instructions

Rel ays

4.0"

HAZARD OF ELECTRIC SHOCK, EXPLOSION, OR ARC FLASH

• Follow safe electrical work practices.

See NFPA 70E in the USA, or applicable local codes.

• This equipment must only be installed and serviced by qualied electrical personnel.

• Read, understand and follow the instructions before installing this product.

• Turn o all power supplying equipment before working on or inside the equipment.

• Use a properly rated voltage sensing device to conrm power is o. DO NOT DEPEND ON THIS PRODUCT FOR VOLTAGE INDICATION

Failure to follow these instructions will result in death or serious injury.

DANGER

INsTallaTION GUIDe

V222

20A SPST Enclosed Relay With

Resistive HOA Monitor

Installer’s Speciﬁcations

Operating Temperature -40° to 60°C (-40° to 131°F) Operating Humidity 10-90% RH, non-condensing Expected Relay Life Electrical (@ rated current) 100,000 cycles; Mechanical (unpowered) 10,000,000 cycles Relay Status LED ON=energized

Wire Specications:

Lead Length 14”(356mm) min. Gauge UL1015; Coil: 18AWG; Contacts: 12AWG; HOA monitor wires: 16AWG Insulation Class 277VAC RMS

Resistive Monitor Maximums:

Volt age Max. 13.4VAC/DC Current Max. 4mA AC/DC Agency Approvals UL 508 enclose d device listing, pollution degree 2

installation

Disconnect and lock out all power sources before beginning the installation.

1. Using the threaded nipple, connect the relay to the desired enclosure through a knock out hole.

2. Secure with the conduit nut provided.

3. Connect coil wires:

• Choose the coil common lead (white with yellow stripe) and connect it to the common (-) source termination point.

NOTICE

• This product is not intended for life or safety applications.

• Do not install this product in hazardous or classiﬁed locations.

• The installer is responsible for conformance to all applicable codes.

• Mount this product inside a suitable ﬁre and electrical enclosure.

Dimensions

(103 mm)

3.8"

(97 mm)

Alta Labs, Enercep t, Enspector, Hawkeye, Trustat, Veris, and the Veris ‘ V’ logo are trademark s or registered tradema rks of Veris Industries, L.L .C. in the USA and /or other count ries.

3/4" NPT Nipple

2.3"

(59 mm)

2.0"

(52 mm)

2.5"

(64 mm)

• Choose either the low voltage (10-30VAC/DC, white with blue stripe) or high voltage (208-277VAC, white with brown stripe) lead, depending on the application requirements, and connect it to the (+) source termination point.*

Note: When connecting the control side of this device (#18 wires) to power line circuits, provide currenting limiting at 7 amps max.

4. Connect relay contacts:

• Choose the two solid orange wires (N.O. contact) and connec t to the switched load.

5. Connect resistive HOA monitor wires:

• Choose the two solid grey wires and connect them to a resistive (0-10kΩ) input in the control system.

6. Secure the enclosure and reconnect power.

7. Program the resistive input to the ranges listed.

* Isolate or insulate all non-terminated wires according to local electrical code requirements, i.e. wire nut.

V222

208-277VAC

24VAC/DC

Common

To Load

To Controls

COIL

CONTACTS

To Load

To Controls

Wire Nut

CONTACTS

HAND

OFF

AUTO

Up position: contacts are closed.

Middle position: contacts are open.

Down position: control system actuates the contacts.

Coil Voltage 24VAC/DC, 208-277VAC

Voltage Coil Current AC DC

24V.................... 75mA 32mA

208V.................. 36mA –

277V.................. 49mA –

TYPICAL COIL PERFORMANCE

CONTACT RATINGS

Resistive..... 20A(r)@240VAC

8A@28VDC 14A@14VDC

Motor......... 250VAC, 1HP N.O. & N.C.

INsTallaTION GUIDe

Wiring Color CoDes

Resistive HOA Position Monitor

Wiring example

Nipple mount directly to a panel Nipple mount to a 2x or 4x electri-

cal box

Hoa positions

ContaCt anD Coil speCifiCations

programming tHe resistive monitor

The resistive monitor is a 0-10 kΩ analog output for monitoring the HOA switch position. Please use the following ranges for the DDC scaling.

Condition Range (Ω)* Nominal Values without Wire

Resistance (Ω)*

Line Open Greater than 8630 n/a

HOA O 5290 to 8630 6190

Alta Labs, Enercep t, Enspector, Hawkeye, Trustat, Veris, and the Veris ‘ V’ logo are trademark s or registered tradema rks of Veris Industries, L.L .C. in the USA and /or other count ries.

HOA Auto 2880 to 5289 3391

HOA On 1200 to 2879 1406

Line Shorted Less than 1200 n/a

* Ranges based on the presence of 0 -1000Ω of resistance due to wire. Average # of feet for 1000Ω by wire AWG listed below.

Wire Type (AWG)

26 12,189

22 30,864

18 78,296

† All 2-wire runs

†

Distance Allowed (ft.)