Veris V201D Installation Instructions
REL AY S
4.0"
HAZARD OF ELECTRIC SHOCK, EXPLOSION, OR ARC FLASH
• Follow safe electrical work practices.
See NFPA 70E in the USA, or applicable local codes.
• This equipment must only be installed and serviced by qualied electrical personnel.
• Read, understand and follow the instructions before installing this product.
• Turn o all power supplying equipment before working on or inside the equipment.
• Use a properly rated voltage sensing device to conrm power is o.
DO NOT DEPEND ON THIS PRODUCT FOR VOLTAGE INDICATION
Failure to follow these instructions will result in death or serious injury.
DANGER
TM
INSTALLATION GUIDE
V201D
V201D
10A SPDT Enclosed Relay With HOA Switch
Installer’s Specifications
Operating Temperature -40° to 55°C (-40 ° to 131°F)
Operating Humidity 10-90% RH, non-condensing
Expected Relay Life Electrical (@ rated current) 100,000 cycles;
Mechanical (unpowered) 10,000,000 cycles
Relay Status LED ON=energized
Wire Specications:
Lead Length 14” (356mm) min.
Gauge UL1015; Coil: 18AWG; Contacts: 16AWG
Insulation Class 600VAC RMS
Agency Approvals UL508 enclosed device listing, pollution degree 2
INSTALLATION
Disconnect and lock out all power sources before beginning the
installation.
1. Using the threaded nipple, connect the relay to the desired enclosure through a
knock out hole.
2. Secure with the conduit nut provided.
Relay #1
3. Connect coil wires:
• Choose the coil common lead (white with yellow stripe) and connect it to
the common (-) source termination point.
• Choose either the low voltage (10-30VAC/DC, white with blue stripe) or
high voltage (208-277VAC, white with brown stripe) lead, depending
on the application requirements, and connect it to the (+) source
NOTICE
• This product is not intended for life or safety applications.
• Do not install this product in hazardous or classified locations.
• The installer is responsible for conformance to all applicable codes.
• Mount this product inside a suitable fire and electrical enclosure.
DIMENSIONS
(103 mm)
3.8"
(97 mm)
2.0"
(52 mm)
Z203419-0B PAGE 1 ©2012 Veris Industries USA 800.354.8556 or +1.503.598.4564 / support@veris.com 04121
Alta Labs, Enercep t, Enspector, Hawkeye, Trustat, Veris, and the Veris ‘ V’ logo are trademark s or registered tradema rks of Veris Industries, L.L .C. in the USA and /or other count ries.
3/4" NPT Nipple
2.3"
(59 mm)
2.5"
(64 mm)
4. Connect relay contacts:
Relay #2
5. Connect coil wires:
6. Connect relay contacts:
7. Secure the enclosure and reconnect power.
* Isolate or insulate all non-terminated wires according to local electrical code requirements, i.e.
wire nut.
termination point.*
NOTE: When connecting the control side of this device (#18 wires) to power
line circuits, provide current limiting at 7 amps max.
• Choose the two solid orange wires (N.O. contact) and connect to the
switched load.
• Choose the coil common lead (white with violet stripe) and connect it to
the common (-) source termination point.
• Choose either the low voltage (10-30VAC/DC, grey with white stripe) or
high voltage (208-277VAC, white with orange stripe) lead, depending
on the application requirements, and connect it to the (+) source
termination point.*
NOTE: When connecting the control side of this device (#18 wires) to power
line circuits, provide current limiting at 7 amps max.
• Choose the two brown wires (N.O. contact) and connect to the switched
load.
V201D
To Load
To Controls
COIL
CONTACTS
To Load
To Controls
Wire
Nut
C
O
I
L
CONTACTS
Pull in Voltage AC DC
10-30V..................................... 8 9
207-277V................................. 154
Drop Out Voltage AC DC
10-30V..................................... 2 3
208-277V................................. 36
Voltage Coil Current
AC DC
10V.......................................... 25mA 14mA
24V.......................................... 31mA 16mA
30V.......................................... 39mA 18mA
208V........................................ 19mA -
277V........................................ 25mA -
TYPICAL COIL PERFORMANCE
CONTACT RATINGS
Resistive.............. 10A@250VAC
Motor.................... 1/3HP@120VAC
Gold Flash............. Yes
HAND
OFF
AUTO
Up position: contacts are closed.
Middle position: contacts are open.
Down position: control system actuates the contacts.
TM
INSTALLATION GUIDE
WIRING COLOR CODES
Relay 1
Relay 2
o
r
a
ng
White
Grey
e
w
h
i
t
e
e
i
t
e
wht/orange
LOW
grey/wht
HI
o
r
a
ng
208-277VAC
w
h
10-30VAC/DC
WIRING EXAMPLE
Nipple mount directly to a panel
CONTACT OUTPUTCONTROL SYSTEM INPUT
GREY
N.C.
VIOLET
Common
Nipple mount to a 2x or 4x electrical box
COMM
wht/violet
v
i
o
l
e
v
i
o
l
e
White
t
t
Common
CONTACT AND COIL SPECIFICATIONS
BROWN
N.O.
HOA POSITIONS
Z203419-0B PAGE 2 ©2012 Veris Industries USA 800.354.8556 or +1.503.598.4564 / support@veris.com 04121
Alta Labs, Enercep t, Enspector, Hawkeye, Trustat, Veris, and the Veris ‘ V’ logo are trademark s or registered tradema rks of Veris Industries, L.L .C. in the USA and /or other count ries.
Loading...