Veris V102 Installation Instructions

REL AYS

4.0"

HAZARD OF ELECTRIC SHOCK, EXPLOSION, OR ARC FLASH

• Follow safe electrical work practices.

See NFPA 70E in the USA, or applicable local codes.

• This equipment must only be installed and serviced by qualied electrical personnel.

• Read, understand and follow the instructions before installing this product.

• Turn o all power supplying equipment before working on or inside the equipment.

• Use a properly rated voltage sensing device to conrm power is o. DO NOT DEPEND ON THIS PRODUCT FOR VOLTAGE INDICATION

Failure to follow these instructions will result in death or serious injury.

DANGER

INSTALLATION GUIDE

V102

10A SPST Enclosed Relay With

Resistive HOA Switch

Installer’s Speciﬁcations

Operating Temperature -40° to 55°C (-40 ° to 131°F) Operating Humidity 10-90% RH, non-condensing Expected Relay Life Electrical (@ rated current) 100,000 cycles; Mechanical (unpowered) 10,000,000 cycles Relay Status LED ON=energized

Wire Specications:

Lead Length 14” (356mm) min. Gauge UL1015; Coil: 18AWG; Contacts: 16AWG; HOA monitor wires: 16AWG Insulation Class 600VAC RMS

Resistive Monitor Maximums:

Volt age Max. 13.4VAC/DC Current Max. 4mA AC/DC Agency Approvals UL508 enclosed device listing, pollution degree 2

INSTALLATION

Disconnect and lock out all power sources before beginning the installation.

1. Using the threaded nipple, connect the relay to the desired enclosure through a knock out hole.

2. Secure with the conduit nut provided.

3. Connect coil wires:

• Choose the coil common lead (white with yellow stripe) and connect it to

NOTICE

• This product is not intended for life or safety applications.

• Do not install this product in hazardous or classiﬁed locations.

• The installer is responsible for conformance to all applicable codes.

• Mount this product inside a suitable ﬁre and electrical enclosure.

DIMENSIONS

4. Connect relay contacts:

(103 mm)

3.8"

(97 mm)

2.0"

(52 mm)

Alta Labs, Enercep t, Enspector, Hawkeye, Trustat, Veris, and the Veris ‘ V’ logo are trademark s or registered tradema rks of Veris Industries, L.L .C. in the USA and /or other count ries.

3/4" NPT Nipple

2.3"

(59 mm)

2.5"

(64 mm)

5. Connect resistive HOA monitor wires:

6. Secure the enclosure and reconnect power.

7. Program the resistive input to the ranges listed.

* Isolate or insulate all non-terminated wires according to local electrical code requirements, i.e. wire nut.

the common (-) source termination point.

• Choose either the low voltage (10-30VAC/DC, white with blue stripe) or high voltage (120VAC, white with black stripe) lead, depending on the application requirements, and connect it to the (+) source termination point.*

NOTE: When connecting the control side of this device (#18 wires) to power line circuits, provide current limiting at 7 amps max.

• Choose the two solid orange wires (N.O. contact) and connec t to the switched load.

• Choose the two solid grey wires and connect them to a resistive (0-10kΩ) input in the control system.

V102

To Load

To Controls

COIL

CONTACTS

To Load

To Controls

Wire Nut

CONTACTS

Pull in Voltage AC DC

10-30V..................................... 8 9

120V........................................ 78

Drop Out Voltage AC DC

10-30V..................................... 2 3

120V........................................ 18

Voltage Coil Current AC DC

10V.......................................... 25mA 14mA

24V.......................................... 31mA 16mA

30V.......................................... 39mA 18mA

120V........................................ 22mA -

TYPICAL COIL PERFORMANCE

CONTACT RATINGS

Resistive.............. 10A@277VAC

Motor.................... 1/3HP@120VAC

Gold Flash............. Yes

HAND

OFF

AUTO

Up position: contacts are closed.

Middle position: contacts are open.

Down position: control system actuates the contacts.

10-30VAC/DC

120VAC

LOW

wht/blue

COMM

wht/yellow

wht/black

CONTACT OUTPUTCONTROL SYSTEM INPUT

Common

INSTALLATION GUIDE

WIRING COLOR CODES

Resistive HOA Position Monitor

WIRING EXAMPLE

Nipple mount directly to a panel Nipple mount to a 2x or 4x electri-

cal box

HOA POSITIONS

CONTACT AND COIL SPECIFICATIONS

Alta Labs, Enercep t, Enspector, Hawkeye, Trustat, Veris, and the Veris ‘ V’ logo are trademark s or registered tradema rks of Veris Industries, L.L .C. in the USA and /or other count ries.

PROGRAMMING THE RESISTIVE MONITOR

The resistive monitor is a 0-10 kΩ analog output for monitoring the HOA switch position. Please use the following ranges for the DDC scaling.

Condition Range* (Ω) Nominal Values without Wire

Resistance* (Ω)

Line Open Greater than 8630 n/a

HOA O 5290 to 8630 6190

HOA Auto 2880 to 5289 3391

HOA On 1200 to 2879 1406

Line Shorted Less than 1200 n/a

* Ranges based on the presence of 0 -1000Ω of resistance due to wire. Average # of feet for 1000 Ω by wire AWG listed below.

Wire Type (AWG)

26 12,189

22 30,864

18 78,296

† All 2-wire runs

†

Distance Allowed (ft.)