Veris TWXWXX Installation Instructions

IMPORTANT NOTE: To comply with FCC & IC RF exposure requirements, the antenna used for this transmitter must be installed to provide a separation distance of at least 20cm from all persons and must not be co-located or operate in conjunction with any other antenna or transmitter.

WIRELESS DEVICES

HWXW SERIES AND TWXWXX

Wireless Temperature and Humidity Sensors

NOTICE

• This product is not intended for life or safety applications.

• Do not install this product in hazardous or classied locations.

• Read and understand the instructions before installing this product.

• Turn oﬀ all power supplying equipment before working on it.

• The installer is responsible for conformance to all applicable codes.

No responsibility is assumed by Veris Industries for any consequences arising out of the

use of this material.

FCC PART 15 INFORMATION NOTE: This equipment has been tested by the manufacturer and found

to comply with the limits for a class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. Modiﬁcations to this product without the express authorization of Veris Industries nullify this statement.

INSTALLATION GUIDE

SPECIFICATIONS

Inputs:

Input Voltage Two 1.5 V AA lithium/iron disulde batteries (3000 mAh min.) Setup Pushbutton setup

Outputs:

Wireless 80 2.11 B/G 2.4 GHz radio Batter y Indicator Indicates low b attery power (read by Gateway or JACE) Temperature Output Range Configur able in software: 0° to 50°C (32° to 122°F) or 10° to 35°C (50° to 95°F)

Accurac y:

Temperature ±0.75°C (typical) Humidity ±2% of full scale @ 25°C

Operating Environment:

Operating Temperature Range 0° to 50°C (32° to 122 °F) Operating Humidit y Range 0 to 95% RH noncondensing Storage Temperature Range -40°C to 50°C (- 40°F to 122°F) Agency Approvals EN61010-1; ETL; CE

PRODUCT OVERVIEW

The Aerospond HWXW Series and the TWXWXX wireless sensors monitor the humidity and temperature, respectively, of the air inside a room. The HWXW series has a temperature option to get both readings in one device. The sensors send environmental readings over a standard building wireless (Wi-Fi) network. The sensors can be integrated with the building controller using either a network wireless gateway (Veris Aerospond NWGWA2), which converts data to either analog or digital outputs, or with a JACE controller and driver (Veris AWB04) for direct integration.

QUICK INSTALL

1. Congure all devices in the wireless network using the Veris conguration software, available at www.veris.com.

2. Ax the backplate on a vertical wall, about 4 ½ feet above the oor, away from ventilation sources.

PRODUCT IDENTIFICATION

Local Display

= No Display

Local Display

= No Display

Wireless

= Wireless

Wireless

WX XX

= Wireless

RH Option

1 = RH 1% NIST 2 = RH 2% NIST H = RH 2%

Accessories (sold separately)

Part Number Description

AWB01 Wi-Fi conguration cable

AWB04 JACE Driver

Alta Labs, Ene rcept, Enspector, Hawk eye, Trustat, Aerospon d, Veris, and the Veris ‘V ’ logo are tradem arks or registe red trademarks o f Veris Industries, L .L.C. in the USA and/or ot her countries.

Temp. Option

X = No temp. T = Temp. transmit ter

3. Insert two 1.5 V AA lithium/iron disulde batteries (3000 mAh min.) into the terminals on the back of the sensor.

4. Mount the sensor onto the backplate and attach the front cover.

DIMENSIONS

3.5"

(89 mm)

4.8"

(121 mm)

1.2"

(30 mm)

HWXW SERIES AND TWXW

INSTALLATION

Observe precautions for handling static sensitive devices to avoid damage to the circuitry that is not covered under the factory warranty.

1. Before mounting this device, congure it to the wireless network using the Veris conguration software. See the Software Conguration Guide, available at www. veris.com.

2. Locate the tab at the top of the sensor housing. Using only the minimum required force, press this tab down and pull the cover outward from the top. Set the cover aside.

Housing, Top View

Tab

3. To remove the backplate, unfasten the sensor from the bottom of the backplate and pivot the sensor outward.

INSTALLATION GUIDE

6. Install two 1.5 V AA lithium/iron disulde (3000 mAh minimum) into the back of the sensor. This device was tested using the Energizer® Ultimate Lithium battery.

Batteries

CAUTION! Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type. Dispose of used batteries according to applicable environmental laws.

7. Install the sensor onto the backplate.

4. Mount vertically on the wall, 4 ½ feet above the oor. Locate away from windows, vents, and other sources of draft. If possible, do not mount on an external wall, as this might cause inaccurate temperature readings.

5. Mount the backplate onto the wall using the screws provided.

Five screwholes available; use a minimum of two for secure mounting.

8. Optional: The sensor normally takes temperature/humidity readings once every ve minutes. Upon commissioning or during troubleshooting, more frequent readings may be necessary. Press and release the setup button on the front of the sensor to increase the sampling rate to once every ve seconds for 360 readings (30 minutes total). After 360 readings, the sampling rate returns to normal.

Optional: The sensor has a reset button that power cycles the device. All mapping and conguration data are retained.

Reset button

Setup button

Optional: The sensor output signal includes a battery indicator. If desired, the gateway can be congured to read this battery indicator and send it to the building controller through its digital output contacts. See the Wireless Conguration Guide for more information.

9. Replace the cover and snap it into position.

+ 1 hidden pages