Veris H8053 Installation Instructions

the user will be required to correct the interference at his own expense.

POWER MONITORING

INSTALLATION GUIDE

ENERCEPT

H8051/H8053

Pulse Output kWh Transducers

US Patent No. 6,373,238

IND. CONT. EQ.

UL 508

DANGER

HAZARD OF ELECTRIC SHOCK, EXPLOSION, OR ARC FLASH

• Follow safe electrical work practices. See NFPA 70E in the USA, or applicable local codes.

• This equipment must only be installed and serviced by qualiﬁed electrical personnel.

• Read, understand and follow the instructions before installing this product.

• Turn oﬀ all power supplying equipment before working on or inside the equipment.

• Use a properly rated voltage sensing device to conﬁrm power is oﬀ. DO NOT DEPEND ON THIS PRODUCT FOR VOLTAGE INDICATION

• Only install this product on insulated conductors.

Failure to follow these instructions will result in death or serious injury.

Installer’s Speciﬁcations

Measurement A ccuracy:

Syste m Accuracy ±1% of reading from 10% to 100% of the rated current * Type of Measurement One or three phase AC system

Input Voltage Characteristics:

Measured AC Voltage 208-480 VAC Frequency Range 50/60 Hz Fuses 1/2A, 600VAC, 200 kAIC

Input Current Characteristics:

Maximum Primary Current 100, 300, 400, 800, 1600, or 2400A**

Meter Current Draw:

Maximum 60mA AC

Output:

Pulse N.O. Opto-Fet Max. Pulse Output Current 100mA@24VAC/DC Field Selectable Pulse Rate 1, 0.5, 0.25, or 0.1 kWh/pulse Pulse Width 200 msec

Mechanical Conditions:

CT Case Iso lation 600VAC Internal Isolation 2000VAC RMS

Environmental Conditions:

Operating Temperature Range 0° to 60°C (32 ° to 140°F) Storage Temperature Range -40° to 70°C (-40° to 15 8°F) Operating Humidity Range <95% RH non-condensing

Safety:

US and Canada (cULus) UL508 (open ty pe device)

* Meter accuracy specied with conduc tors centered in the CT window.

CAUTION

** For amperages greater than 2400A, see App Note VN19, www.veris.com/applicationnotes.aspx

RISK OF EQUIPMENT DAMAGE

• Enercept meters are rated for use at 50-60Hz. Do not connect this product to circuits with high harmonic energy, such as Variable Speed Drives (a.k.a. Variable Frequency Drives, Adjustable Frequency Drives) or similar sources, as these may permanently damage the product.

Failure to follow these instructions can result in overheating and permanent

equipment damage.

QUICK INSTALL

Disconnect and lock out power to the enclosure containing the conductor before installation.

1. Set the pulse rate switches located on the bottom of the CT(s).

2. Connect the voltage leads to the source to be monitored.

NOTICE

• This product is not intended for life or safety applications.

• Do not install this product in hazardous or classiﬁed locations.

• The installer is responsible for conformance to all applicable codes.

• Mount this product inside a suitable ﬁre and electrical enclosure.

FCC PART 15 INFORMATION NOTE: This equipment has been tested by the manufacturer and found

to comply with the limits for a class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case

Modiﬁcations to this product without the express authorization of Veris Industries nullify this statement.

For use in a Pollu tion Degree 2 or bet ter environment only. A Pollut ion Degree 2 environme nt must control conductive pollution and the possibility of condensation or high humidity. Consider the enclosure, t he correct use of ven tilation, thermal pro perties of the equ ipment, and the relatio nship with the env ironment. Installat ion category: CAT II or C AT III

Alta Labs, Enercep t, Enspector, Hawkeye, Trustat, Veris, and the Veris ‘ V’ logo are trademark s or registered tradema rks of Veris Industries, L.L .C. in the USA and /or other count ries.

3. Snap the CT(s) onto the conductor (observe color matching).

4. Connect the pulse output wires (observe polarity).

SMALL

100/300 Amp

MEDIUM

400/800 Amp

LARGE

800/1600/2400 Amp

A = 3.8" (96 mm) B = 1.2" (30 mm) C = 1.3" (31 mm) D = 1.2" (30 mm) E = 4.0" (100 mm) F = 4.8" (121 mm)

A = 4.9" (125 mm) B = 2.9" (73 mm) C = 2.5" (62 mm) D = 1.2" (30 mm) E = 5.2" (132 mm) F = 6.0" (151 mm)

A = 4.9" (125 mm) B = 5.5" (139 mm) C = 2.5" (62 mm) D = 1.2" (30 mm) E = 7.9" (201 mm) F = 6.0" (151 mm)

H8051/H8053

INSTALLATION GUIDE

OPERATION

The H8051 and H8053 pulse output meters combine microprocessor-based kWh transducers and high-accuracy split-core instrument grade current transformers (CTs) in one unit. The H8051 is a single CT version designed for balanced loads, and the H8053 is a 3-CT version for monitoring each phase. Integration of electronics lowers hardware and installation costs. The sensors automatically detect phase reversal, so CT load orientation is not a concern. The CTs and meters are calibrated as a set, so it is necessary to color-match the CTs and voltage leads when installing.

These devices are used in tenant submetering, performance contrac ting, and departmental costing applications. The 1% total system accuracy conforms to ANSIC12.1 metering standards.

PRODUCT IDENTIFICATION

Single CT Units

MODEL MAX. AMPS CT SIZE

H8051-0100-2 100 SMALL

H8051-0300-2 300 SMALL

H8051-0400-3 400 MEDIUM

H8051-0800-3 800 MEDIUM

H8051-0800-4 800 LARGE

H8051-1600-4 1600 LARGE

H8051-2400-4 2400 LARGE

DIMENSIONS

Three-CT Units

MODEL MAX. AMPS CT SIZE

H8053-0100-2 100 SMALL

H8053-0300-2 300 SMALL

H8053-0400-3 400 MEDIUM

H8053-0800-3 800 MEDIUM

H8053-0800-4 800 LARGE

H8053-1600-4 1600 LARGE

H8053-2400-4 2400 LARGE

PRODUCT DIAGRAM

Enercept

1. Voltage Leads

2. Fuses

3. Pulse Output connector

4. Status LED: blink codes: slow green for normal operation; slow red for incorrect wiring or low power factor (less than 0.5); fast red for max. current exceeded.

5. Pulse Rate Switches: used to set the pulse output rate.

Alta Labs, Enercep t, Enspector, Hawkeye, Trustat, Veris, and the Veris ‘ V’ logo are trademark s or registered tradema rks of Veris Industries, L.L .C. in the USA and /or other count ries.

6. External CTs: permanently attached; do not disconnect or use with other power meters.

Color match CTs and voltage leads! Example: clamp the red labeled CT around the power conductor connected to the red voltage wire.

+ 3 hidden pages