Veris AE011 Installation Instructions

POWER MONITORING

INSTALLATION GUIDE

AE010/AE011

Pictured with meter and locking assembly installed; E5x meter, AE010 enclosure, and AE011 locking assembly must all be ordered separately.

DANGER

HAZARD OF ELECTRIC SHOCK, EXPLOSION, OR ARC FLASH

• Follow safe electrical work practices. See NFPA 70E in the USA, or applicable local codes.

• This equipment must only be installed and serviced by qualied electrical personnel.

• Read, understand and follow the instructions before installing this product.

• Turn o all power supplying equipment before working on or inside the equipment.

• Use a properly rated voltage sensing device to conrm power is o. DO NOT DEPEND ON THIS PRODUCT FOR VOLTAGE INDICATION

Failure to follow these instructions will result in death or serious injury.

RoHS

Compliant

AE010/AE011

Enclosure for E5x Series Energy Meters with

Optional Locking Mechanism

OPERATION

The AE010 enclosure oers a mounting option for E5x Series energy meters that helps protect from tampering and the elements. The enclosure is equipped with DIN rail mounting hardware for easy installation and a NEMA 4X rating for durability. The optional AE011 keylock provides additional security from unwanted tampering (AE010 and AE011 are sold as separate units).

DIMENSIONS (AE010)

Front Side, Cross Section

5.7”

(144 mm)

1.8”

(46 mm)

7.2”

(182 mm)

7.1”

(180 mm)

2.5”

(62 mm)

(110 mm)

4.4”

(123 mm)

1.8”

(45 mm)

4.9”

1.4”

(35 mm)

1.9”

(47 mm)

NOTICE

• This product is not intended for life or safety applications.

• Do not install this product in hazardous or classiﬁed locations.

• The installer is responsible for conformance to all applicable codes.

Alta Labs, Enercep t, Enspector, Hawkeye, Trustat, Veris, and the Veris ‘ V’ logo are trademark s or registered tradema rks of Veris Industries, L.L .C. in the USA and /or other count ries.

INSTALLATION

The AE010 components:

AE010/AE011

INSTALLATION GUIDE

2. Mount the AE010 enclosure to a wall or panel

1. Enclosure base

2. Enclosure cover with hinged, clear shield

3. Optional keys, locking me chanism, and pin (sold separately as the Veris AE011)

4. Mounting screw caps

5. Spacer block

6. Cover retention screws

1. Install DIN Rail Clips to the back of the E5x

The E5x is shipped with a set of three DIN rail clips included. Insert these clips into the slots on the back of the housing from the middle, moving outward. Stopping pegs must face the underside of the housing. Push clips into place until there is an audible click.

DIN Rail clip

(included with E5x meter)

Take care to protect the equipment from drill chips, ﬁlings, and other contaminants when making the wire entry holes and mounting the enclosure to prevent component damage or a future malfunction.

Cut holes cut in the enclosure for wire conduit connections prior to the installation of the meter in the enclosure. Seal all holes properly to maintain the enclosure rating.

The AE010 enclosure base can be installed using either a 2-point or a 4-point screw mounting.

Punchout the corner holes for 4-point mounting:

Mounting screw caps can be used to cover screw heads.

Drill out the center holes for 2-point mounting:

3. Install E5x Onto DIN Rail Inside the AE010

Push the top of the E5x onto the DIN rail.

When attaching the clips to the unde rside

of the E5x meter, these stopping pegs must

face inward towards the meter housing. Set

pegs into the available slots o n the meter,

with the beveled side of the clip facing

toward the center of the meter.

Then push the bottom of the meter onto the DIN rail until there is an audible click.

When all clips are in place, the white clips must be ush with the top edge of the housing, and the black clip must protrude slightly past the bottom edge.

Alta Labs, Enercep t, Enspector, Hawkeye, Trustat, Veris, and the Veris ‘ V’ logo are trademark s or registered tradema rks of Veris Industries, L.L .C. in the USA and /or other count ries.

+ 2 hidden pages