Veris AE006 Installation Instructions

POWER MONITORING

INSTALLATION GUIDE

AE006

E30 Current Sensor Repair Kit

RoHS

(H68 03R-010 0 CT on ly)

DANGER

HAZARD OF ELECTRIC SHOCK, EXPLOSION, OR ARC FLASH

• Follow safe electrical work practices. See NFPA 70E in the USA, or applicable local codes.

• This equipment must only be installed and serviced by qualiﬁed electrical personnel.

• Read, understand and follow the instructions before installing this product.

• Turn oﬀ all power supplying equipment before working on or inside the equipment.

• Use a properly rated voltage sensing device to conﬁrm power is oﬀ. DO NOT DEPEND ON THIS PRODUCT FOR VOLTAGE INDICATION

• Only install this product on insulated conductors.

Failure to follow these instructions will result in death or serious injury.

Compliant

INSTALLATION

Disconnect and lock out power to the panel.

1. Remove the at ribbon cable connecting the CT strip to the headers on the E30 main circuit board.

2. Install the AE006 adapter board into the electrical panel using SNAPTRACK or DIN rail clips (both included) inside the panel.

3. Use the included round ribbon cable to connect the header on the E30 main circuit board to the header on the repair kit adapter board labelled “METER.” Use the existing ribbon cable to connect the CT strip to the header on the repair kit adapter board labelled “STRIP.”

METER

STRIP

Observe precautions for handling static sensitive devices to avoid damage to the circuitry that is not covered under the factory warranty.

NOTICE

• This product is not intended for life or safety applications.

• Do not install this product in hazardous or classiﬁed locations.

• The installer is responsible for conformance to all applicable codes.

• Mount this product inside a suitable ﬁre and electrical enclosure.

PRODUCT IDENTIFICATION

AE006 E30 Current Sensor Repair Kit (includes one AE006

board, one 100A split-core CT, and one 18-inch round ribbon cable)

OPERATION

The AE006 E30 CT repair kit provides a solution for mechanically damaged or suspect CTs within the E30 panelboard monitoring system. The kit includes one AE006 board with a single 100A split-core CT and a ribbon cable. The AE006 board is connected to the main E30 board via ribbon cable. The split-core CT is wired to the AE006 board, and it replaces the damaged sensor on the solid-core CT strip.

DIMENSIONS

4.0”

(102 mm)

METER

2.75”

(70 mm)

100 Amp

A = 1.2” (29 mm) B = 0.8” (20 mm) C = 0.7” (16 mm) D = 1.6” (40 mm) E = 2.1” (53 mm)

20 18 16 14 12 10 8 6 4 2

21 19 17 15 13 11 9 7 5 3 1

4. Use the numbers in the above

Conductor

diagram to identify the damaged current sensor on the solid-core strip. This number corresponds to a specic terminal block and jumper on the

Split-core CT Note: Clean split-core contacts before closing.

adapter board.

5. Wire a split-core CT to the terminal block corresponding to the damaged

METER

sensor on the strip. When tightening terminals, ensure that the correct torque is applied: 1.92 to 2.28 in-lb

STRIP

(0.22 to 0.269 N-m)

6. Snap this new CT onto the conduc tor in the panel. Clean contacts before closing CT.

Close CTs until the clasp clicks

into place to ensure that contact

surfaces are rmly seated.

7. Remove the jumper corresponding to the damaged sensor. The jumper can be either stored on one of the pins or discarded.

8. Repeat steps 4 through 6 for each damaged current sensor (one replacement 100A split-core CT is included with the AE006; additional CTs (H6803R-0100) are available for purchase).

✓

9. Reconnec t power to the panel. Note there is a 2% decrease in accuracy for the

STRIP

repaired circuit.

Alta Labs, Enercep t, Enspector, Hawkeye, Trustat, Veris, and the Veris ‘ V’ logo are trademark s or registered tradema rks of Veris Industries, L.L .C. in the USA and /or other count ries.

AE006

INSTALLATION GUIDE

CHINA ROHS COMPLIANCE INFORMATION (EFUP TABLE)

产品中有毒有害物质或元素的名称及含量Substances

部件名称

铅 (Pb) 汞 (Hg) 镉 (Cd) 六价铬 (Cr(VI)) 多溴联苯(PBB) 多溴二苯醚(PBDE)

电子线路板 X O O O O O

O = 表示该有毒有害物质在该部件所有均质材料中的含量均在 SJ/T11363-2006 标准规定的限量要求以下. X = 表示该有毒有害物质至少在该部件的某一均质材料中的含量超出SJ/T11363-2006标准规定的限量要求.

Z000057-0A

Alta Labs, Enercep t, Enspector, Hawkeye, Trustat, Veris, and the Veris ‘ V’ logo are trademark s or registered tradema rks of Veris Industries, L.L .C. in the USA and /or other count ries.