Veris 1008 User Manual
1008
Rev. 2.x Meters
Indoor Air Quality Meter
The Value Leader
TM
www.tpi-thevalueleader.com
1. Introduction
Thank you for purchasing TPI brand products. The TPI 1008 Indoor Air
Quality (IAQ) Meter is a state of the art, easy to use tester designed to
provide you with the necessary measurements to monitor and make
adjustments to air handling devices. The instrument is ruggedly constructed and comes with a 3 Year unit and 2 Year sensor Guarantee.
2. General Overview
The 1008 IAQ meter uses state of the art sensors to measure carbon
dioxide (CO2), and temperature. The CO2 sensor in your meter will
need to be replaced periodically and calibration is recommended once
every year.
You should keep battery power applied to your sensors at all times.
The following guidelines will help prevent damage to your sensors:
Always store your unit in a place where the temperature does not get
down to or below freezing.
Always maintain battery power to the sensors. When the batteries get
low replace them as soon as possible.
Never allow foreign objects or material to enter the sensor holes, damage to the sensor may result.
Contents
1. Introduction
2. General Overview
3. Familiarization
3.1 Front View
3.2 Soft Keys
3.3 Back View
4. Operation
4.1 Turning On & Off / Performing a Test / Main Display
4.2 Selecting Temperature Units
4.3 Min / Max Mode
4.4 Activating the Backlight
4.5 Setting CO2 Alarm Level
5. Data Logging
6. Retrieving Logged Data
7. Technical Specifications
8. Maintenance
8.1 Battery Replacement
8.2 Service
9. Technical Information
10. Error Codes & Troubleshooting
3. Familiarization
3.1 Front View
Sensor Locations: Places where the CO and Temperature sensors
are located and protected.
Display : Large 2 Parameter Backlit LCD Display.
Protective Rubber Boot Provides protection to meter housing and sensors.
Keypad Selects all available functions
USB Port Location for connection of USB cable for PC com
munication.
Power Adapter Socket Location to connect power adapter.
General Overview (Continued)
This manual will guide you through the functions of the TPI 1008
which will give you many years of reliable service.
Your TPI 1008 Indoor Air Quality meter comes complete with the
following standard accessories:
• TPI 1010 Instrument
• Protective Rubber Boot (A800)
• Soft Carrying Case (A921)
• USB Cable & Software (A803)
• Instruction Manual
Your TPI 1008 Indoor Air Quality meter has the following optional
accessories available:
• Power adapter / Battery eliminator (A804)
• Magnetic strap kit to hang meter (A127)
• Boot hook to hang meter (A103)
• Replacement Software only (A802)
• Replacement USB cable only (A801)
( ) Denotes part number
Display
Keypad
CO2 &
Temperature
Sensor Location
USB Port
Power Adapter
Socket
Protective
Rubber Boot
3.3 Back View3.2 Soft Keys
On / Off key - Used to turn the IAQ meter on or off. Press to turn
on, press and hold to turn off.
Up Arrow key - Used to select and change parameters.
Down Arrow key - Used to select and change parameters.
Mode key - Used to switch between Celsius and Fahrenheit units
of display and to enter CO2 alarm level input mode. Press to
switch between Celsius and Fahrenheit units. Press and hold to
enter and exit CO2 alarm level mode.
Backlight key - Used to turn the display backlight on and off.
Min / Max key - Used to activate and cycle through minimum,
maximum, and average display modes. Press to activate Min/Max
mode, press repeatedly to cycle through min, max, and avg displays. Press and hold to deactivate Min/Max mode.
Log key - Used activate and deactivate data logging.
RCL Key - Used to recall (display) logged data.
Tilt Stand
Battery Cover Screw
Hanger Hole
Hanger Hole: Use to hang instrument for hands free operation. Can
be used with A127 magnetic strap kit or A103 hook.
Tilt Stand: Use to stand instrument on a table.
Batter Cover Loosen this screw and open cover to access batteries.
Screw:
Loading...