Verint Systems S1900e-AS, S1950e, S1970e, S1970e-R User Guide

Nextiva S1900e Series
User Guide
Covering the S1900e-AS, S1950e, S1970e,
and S1970e-R
Firmware Release 4.80/5.0 March 2009
By providing this document, Verint Systems Inc. is not making any representations re­garding the correctness or completeness of its contents and reserves the right to alter this document at any time without notice.
Features listed in this document are subject to change. Please contact Verint for current product features and specifications.
All marks referenced herein with the ® or TM symbol are registered trademarks or trade­marks of Verint Systems Inc. or its subsidiaries. All rights reserved. All other marks are trademarks of their respective owners.
© 2009 Verint Systems Inc. All Rights Reserved Worldwide.
www.verint.com/videosolutions
Publication date: March 11, 2009 Publication revision: C
Contents
Preface ................................................................................................................ v
Chapter 1 Overview ..........................................................................................1
About the S1900e Series ................................................................. ..................2
Key Features ..................................... ... .. ......................... .. .. .......................2
Video Analytics ...........................................................................................3
Receiver Modes ..........................................................................................3
Security .....................................................................................................3
Frame Rate and Performance ........................................................................3
Installation Kit .......................... ........................... .. ............................ .. ............6
Hardware Overview ..........................................................................................7
Chapter 2
Installing the Device .........................................................................................9
Configuring the Device ....................................................................................13
Configuring the I/Os .......................................................................................17
Chapter 3
Installing or Upgrading ActiveX Controls ............................................................22
Viewing the Quick Status .................................................................................24
Configuring the Device ....................................................................................26
Configuring and Installing the Device ...............................................8
Connecting Power .......................................................................................9
Installing the S1900e ................................................................................11
Performing Serial Connections ....................................................................11
Setting Network Parameters .......................................................................13
Performing a Point-to-Point Connection ........................................................ 15
Alarms .................................................................................................... 18
Audio ...................................................................................................... 18
Data Transmission................................................................................18
Audio Input/Output Types .....................................................................19
Specifications ......................................................................................20
Using the Web Interface ................................................................. 21
Configuring the Serial Port ......................................................................... 26
Configuring Access Management .................................................................27
User Accounts......................................................................................27
Security..............................................................................................29
Viewing the System Status .........................................................................31
Configuring the Network ............................................................................32
Configuring Video ..................................................................................... 33
General Parameters for Transmitters.......................................................33
Encoder .............................................................................................. 34
General Parameters for Receivers...........................................................39
Decoders.............................................................................................42
Looking at Video Status .......................................................... .. .................43
Configuring VSIP .......................................................................................44
Configuring Audio .....................................................................................45
Configuring System Time ........................................................................... 47
Configuring On-Screen Display ................................................................... 48
Configuring HTTP (Webserver) ....................................................................52
Verint Video Intelligence Solutions 3
Contents
Viewing Live Video ..........................................................................................53
Configuring Live Video ...............................................................................53
Manipulating the PTZ Camera .....................................................................57
Maintaining the Device ....................................................................................58
Chapter 4
Maintaining and Troubleshooting the Device ...................................61
Updating the Firmware ....................................................................................62
Performing a Reset .........................................................................................62
Losing Connection to a Camera .........................................................................63
Recognizing the Status LED Conditions ..............................................................63
Using the Command Line Interface ............................ .. ............................ ..........64
Accessing the CLI ......................................................................................64
Configuring Quality of Service .....................................................................66
Appendix A Appendix B
Factory Default Configuration........................................................67
DHCP Support and APIPA ..............................................................69
Appendix C Audio Pinouts ................................................................................71
Appendix D Technical Specifications ................................................................73
Glossary ............................................................................................................. 76
Index .................................................................................................................81
Compliance ........................................................................................................84
United States Statement for FCC ......................................................................85
Industry Canada Statement ............................. .. .. .. ..........................................85
Europe EN 55022 Statement ....................................................................... .. .. .86
RoHS Declaration of Compliance .......................................................................87
4 Verint Video Intelligence Solutions

Preface

The Nextiva S1900e Series User Guide presents the information and procedures on installing, configuring, and using the Nextiva® S1900e series edge devices.
This guide covers the following firmware versions:
Edge Device Version
S1900e-AS 5.0 S1950e 4.80 S1970e 4.80 S1970e-R 5.0
Audience
This guide has been prepared for the following audience:
Managers IT system administrators Engineers Technicians
This guide assumes that you are familiar with:
Installation and manipulation of electronic equipment General use of computers Local area networks (LANs) and basic IP data communication concepts and practices Pan-tilt-zoom (PTZ) platforms (cameras and keyboards) Web browsers Microsoft Windows operating systems
Reference
In addition to this guide, the following documentation is also available:
Nextiva S1900e Series Installation Guide Verint SConfigurator User Guide Nextiva S1900e-AS Release Notes Nextiva S1950e S1970e Release Notes Nextiva S1970e-R Release Notes
A paper copy of the installation guide is included with your order.
Verint Video Intelligence Solutions v
Preface
How to Contact Us
The following Web sites and e-mail addresses provide information and support for Verint Video Solutions and the Nextiva Intelligent Edge Device product line.
Find general information on Verint Video Solutions, including marketing material and product information at www.verint.com/videosolutions
. Download the documentation of the Intelligent Edge Devices at www.verint.com/manuals Download firmware from the Verint Video Solutions partner extranet at
http://vvs.verint.com
.
Send your questions or comments on the current document, or any other Nextiva user documentation, to our documentation feedback team at
documentationfeedback@verint.com
.
Find contact information for the Verint Customer Service team, by phone or e-mail, or fill out a Web request for support with a specific issues at www.verint.com/videoservice
. For
immediate assistance, contact the Customer Service team:
Location Telephone E-mail
USA and Canada 1-888-747-6246 vissupport@verint.com
.
Central and Latin
+1-631-962-9202 vissupport@verint.com
America Europe, Middle East,
+44 (0) 845-843-7333 customersupport.emea@verint.com
and Africa
+49 (0) 4321-269 81 36 mobilesupport@verint.com
(Transit applications only) Asia/Pacific Hong Kong Singapore
+852 2797 5678 +65-68266099
APAC_VIS_Services@verint.comp
Warranty
Each product manufactured by Verint Video Solutions Inc. is warranted to operate substantially in accordance with the end user documentation delivered with the product for the period indicated in the applicable Verint Product Guide. Verint shall have no responsibility or liability of any kind, whether for breach of warranty or otherwise, arising or resulting from errors resulting from misuse, abuse, negligence, or improper use or installation of all or any part of the product, or problems to or caused by products or services not provided by Verint. V erint shall ha ve no responsibility for product modifications or changes by any party other than V erint or V erint’s representative expressly authorized to make such modification or change. The customer’s exclusive remedy under this warranty shall be for Verint, in its sole discretion to use commercially reasonable efforts either to correct any verifiable material nonconformity or to replace the materially nonconforming portion of the product. Verint provides all third party hardware on an “AS IS” basis without warranties of any kind, unless Verint specifies otherwise. In certain cases, such third party
vi Verint Video Intelligence Solutions
Nextiva S1900e Series User Guide
Hardware may be accompanied by the manufacturer’s own warranty and warranty service must be obtained directly from the third party manufacturer. In the event any Verint product is to be returned to Verint for warranty repair, a return material authorization (“RMA”) must be obtained from Verint prior any return. Transportation charges for return of hardware shall be paid by the customer. All replaced hardware or parts become Verint’s property, except for video or similar data files contained in the hard drive of any product which shall be returned or destroyed at customer’s request. Except as stated above, Verint makes no other warranties, express or implied, relating to the products.
Verint Video Intelligence Solutions vii

Overview

Designed for video monitoring and surveillance over IP networks, the Nextiva S1900e series is a highly compact, single-input or -output edge device.
On the transmitters, the following compression modes (also called codecs—coder/decoder) are available to deliver video over 10/100Base-T networks: a proprietary MPEG-4-based mode, the MPEG-4 ISO 14496-2 compliant mode, and MJPEG (Motion JPEG). The device can easily be extended over local and wide area networks (LANs and WANs) or the Internet using ISDN, PSTN, or xDSL routers. It is built on open standards to provide long-term investment protection.
On the receiver, you have access to three video display modes. The overview covers the following:
About the S1900e series Installation kit Hardware overview
Verint Video Intelligence Solutions 1
Nextiva S1900e Series User Guide

About the S1900e Series

You can use the S1900e series edge devices in point-to-point contexts as well as with video management and storage applications. Furthermore, they enable configuration, live video viewing, and maintenance from web browsers.
The following suffixes may be used in the product names:
-T for transmitters -R for receivers
When no suffix is used, it is assumed that the device is a transmitter. This device is for indoor use only.

Key Features

The S1900e series devices contains three transmitters and one receiver, covering different video resolution and functionality needs:
Device Video I/O On-Board
Analytics
S1900e-AS 1 input S1950e 1 input 12V DC S1970e 1 input 12V DC or power
S1970e-R 1 output 12V DC
The S1900e series offers the following additional features:
A serial port for the RS-422/485 protocol Dual video encoding on the transmitters One input contact and one output relay 1/8 inch (3.5 mm) stereo jacks for audio Default serial port settings compatible with the most popular camera data port
configuration (4800 baud, 8 data bits, no parity, 1 stop bit) Integration with the Nextiva enterprise video management solution You can also purchase each device with the extended temperature option (the
S1900e-AS-XT, S1950e-XT, S1970e-XT, and S1970e-R-XT). Unless otherwise specified, the word S1900e refers to any of these devices.
33
Camera Tampering Detection
Power
12V DC
over Ethernet (PoE)
Verint Video Intelligence Solutions 2
1: Overview

Video Analytics

The on-board video analytics capabilities of the S1900e-AS can be used inside a Nextiva IntelliView solution. In the IntelliView Analytics Rule Builder, the S1900e-AS supports a maximum of five active rules and six views. For more information, refer to the documentation set of the Nextiva enterprise video management platform.
The analytics license is not included with the device. For details, refer to your Verint representative.

Receiver Modes

The S1970e-R can display video streams coming from up to four transmitters on a single analog monitor, to create a maximum of four different point-to-point connections; you create these connections in SConfigurator (see page 15). You can choose between the following video display modes: solo, quad, and guard tour (for more information, see page 39).

Security

Every edge device comes with a unique SSL (Secure Sockets Layer) certificate for securing its IP link. SSL is a commonly used protocol for managing the security of IP message transmission. If enabled, the SSL protocol secures the following data: I/O, serial port, and VSIP (a proprietary protocol) communication. It does not apply to audio and video transmission.

Frame Rate and Performance

The available video frame rates of each encoder of the transmitter are:
NTSC—1 to 7, 10, 15, or 30 frames per second (fps) PAL—1 to 6, 8, 12, or 25 fps
The composite signal of a video input is sent to two separate encoders. You can customize each encoder to meet your system needs, for instance in terms of frame rate and resolution. Here are typical scenarios regarding encoder use:
Scenario Encoder 1 Encoder 2
point-to-point point-to-point unused
unused point-to-point
point-to-point and web interface web viewing at rate A point-to-point at rate B
web viewing and point-to-point at rate C
video management software view at rate D record at rate E
unused
3 Verint Video Intelligence Solutions
Nextiva S1900e Series User Guide
Note: You should not use the web interface and a video management software at the
same time to avoid configuration conflicts.
The transmitters in the S1900e series can have the following video resolutions:
Resolution Number of Columns Number of Lines
NTSC/PAL NTSC PAL
QCIF 176 128 144 CIF 352 240 288 2CIF 704 240 288 4CIF 704 480 576 All lines 352 480 576 2/3 D1 480 480 576 VGA 640 480 480
The following performances can be achieved using single-stream encoding. For dual encoding values, refer to the Nextiva Intelligent Edge Devices Single-Dual Stream Performance document, available on the extranet (Community Links > Technical Briefs > Nextiva Intelligent Edge Devices).
Each video encoder of an S1900e transmitter can have the following performances with the proprietary MPEG-4-based compression mode:
Resolution Maximum Frame Rate, in Frames per Second Using the NTSC (PAL)
Format for the MPEG-4-Based Mode S1900e-AS S1950e S1970e
QCIF 30 (25) 30 (25) 30 (25) CIF 30 (25) 30 (25) 30 (25) 2CIF 30 (25) 30 (25) 30 (25) 4CIF
30 (25)
1
15 (12.5) 30 (25)
All lines 30 (25) 30 (25) 30 (25) 2/3 D1 30 (25) 30 (25) 30 (25) VGA
30 (25)
1
15 (12.5) 30 (25)
Verint Video Intelligence Solutions 4
1: Overview
1
On encoder 2 only.
Each video encoder of an S1900e transmitter can have the following performances with the MPEG-4 ISO 14496-2 compliant compression mode:
Resolution Maximum Frame Rate, in Frames per Second Using the NTSC (PAL)
Format for the MPEG-4 ISO 14496-2 Compliant Mode S1900e-AS S1950e S1970e
QCIF 30 (25) 30 (25) 30 (25) CIF 30 (25) 30 (25) 30 (25) 2CIF 30 (25) 30 (25) 30 (25) 4CIF
30 (25)
2
15 (12.5) 30 (25)
All lines 30 (25) 30 (25) 30 (25) 2/3 D1 30 (25) 30 (25) 30 (25) VGA
2
On encoder 2 only.
30 (25)
2
15 (12.5) 30 (25)
Each video encoder of the S1950e and S1970e transmitter, and the first encoder of the S1900e-AS, can have the following performances with the MJPEG compression mode:
Resolution Maximum Frame Rate, in Frames per Seco nd Using the NTSC (PAL)
Format for MJPEG S1900e-AS S1950e S1970e
QCIF 30 (25) 30 (25) 30 (25) CIF 30 (25) 30 (25) 30 (25) 2CIF 30 (25) 30 (25) 30 (25) 4CIF 15 (12.5) 15 (12.5) 30 (25) All lines 30 (25) 30 (25) 30 (25) 2/3 D1 30 (25) 30 (25) 30 (25) VGA
3
Without noise, I/Os, and other factors affecting quality , the device can achiev e the highest
30 (25)
3
30 (25)
3
30 (25)
frame rate.
5 Verint Video Intelligence Solutions
Nextiva S1900e Series User Guide
On the S1970e-R receiver, the performances for displaying video on an analog monitor vary depending on the video display mode (for more information, see page 39) and the compression mode. The following perf ormances are for the maximum frame rate (NTSC/PAL); the other resolutions and bit rates are also available, with lower frame rates:
Video Display Mode Compression Mode
Proprietary MPEG-4-Based
Solo 4CIF at 30/25 fps
and 6000 kbps
Quad CIF at 30/25 fps and
800 kbps
Guard T our CIF at 30/25 fps and
800 kbps
MPEG-4 ISO MJPEG
4CIF at 30/25 fps and 5000 kbps
CIF at 30/25 fps and 800 kbps
CIF at 30/25 fps and 800 kbps
4CIF at 10/8 fps and 40 KBytes
CIF at 10/8 fps and 10 KBytes
CIF at 10/8 fps and 10 KBytes

Installation Kit

The package contents are:
Item Description
Transmitter or receiver S1900e-AS or S1950e or S1970e or S1970e-R 12V DC external power
supply Printed material The Nextiva S1900e Series Installation Guide
Option
A universal power supply for all devices except the S1970e with PoE
Power-over-Ethernet (PoE) kit
Verint Video Intelligence Solutions 6
An IEEE 802.3af class 3 injector and power cord
1: Overview
RS-422/485 Video input or output (S1970e-R)
Audio input
Audio output
I/O Network or PoE (RJ-45)Reset
12V DC power
System status

Hardware Overview

The S1900e electronics are enclosed in a non-weatherproof aluminum casing that is not meant for outdoor use.
The front panel consists of:
A multipin connector for the RS-422/485 serial port A pair of 1/8 inch (3.5 mm) I/O audio connectors One BNC connector for video input or output
The back panel consists of:
A system status LED 12V DC power pins A reset button One input contact and one output relay An RJ-45 jack for the Ethernet network or PoE (on the S1970e only)
7 Verint Video Intelligence Solutions
Configuring and
Installing the Device
The steps required to prepare your S1900e device for operation are:
Installation Basic configuration I/O configuration
Remember that your device is an indoor product that should not be used in an outdoor environment.
Verint Video Intelligence Solutions 8
2: Configuring and Installing the Device

Installing the Device

The installation process varies depending on the power source, 12V DC or power-over-Ethernet (PoE). Then you may connect the device to serial equipment.

Connecting Power

All devices can use 12V DC for power supply . Verint offers a universal 12V DC power supply as part of your package. For any other power supply, refer to the manufacturer documentation for the proper wiring scheme.
You can also use PoE to power the S1970e transmitter and establish its Ethernet connection. The PoE kit sold by Verint contains two items: an injector and a power cord. The connection procedure may vary if you use another PoE kit; refer to the PoE kit documentation for more information.
Warning: Never use PoE and 12V DC at the same time; otherwise you may damage the
device.
To power the device using the universal 12V DC power supply:
1. If the electrical plug installed on the power supply is the right one for the country of
operation, go to step 4.
2. Remove the installed plug by pushin g the PU SH button and keeping it pushed while
turning the plug in the counterclockwise direction.
3. Insert the required plug on the power supply then turn it in the clockwise direction until
you hear a click.
4. Plug the power supply wire with the dashed white lines in the Gnd pin on the back of
the device.
5. Plug the other power wire in the Pwr+ pin on the back of the device.
6. Connect the electric plug into the outlet.
9 Verint Video Intelligence Solutions
Nextiva S1900e Series User Guide
1
2 3
4
J2
DATA
J1
DATA & PWR
5
Power cord
PoE injec tor
Straight-through Ethernet cable
Ethernet cable (straight-through or crossover)
To connect the PoE kit sold by Verint:
1. Plug a straight-through Ethernet cable into the network (RJ-45) connector of the
device.
2. Plug the other end of the cable into the DATA & PWR port of the injector.
3. Connect another Ethernet cable (straight-through or crossover) into the DATA port of
the injector.
The crossover cable directly connects the IP camera to a computer; use a
straight-through cable to connect the IP camera to a hub or a switch for integration
with the network.
4. Connect the other end of the second cable into an Ethernet equipment.
5. Power the device by plugging the power cord between the injector and the outlet.
Verint Video Intelligence Solutions 10
Warning: To avoid damaging your Ethernet equipment, ensure that the cable is
connected into the DATA port of the PoE injector, and not in the DAT A & PWR port.
Note: The combined length of the two Ethernet cables cannot exceed 328 feet
(100 meters). For example, if you used an 82-foot (25m) cable in step 1, the maximum length of the second cable is 246 feet (75m).
2: Configuring and Installing the Device

Installing the S1900e

Install the S1900e device and connect it to its peripherals.
Note: The S1900e-AS may heat more than a device without analytics capabilities.
To install the device:
1. For a 12V DC device:
a. Establish its Ethernet connection by plugging a cable (straight-through or
crossover) between the network (RJ-45) connector on the back of the device and an Ethernet device.
The crossover cable directly connects the IP camera to a computer; use a straight-through cable to connect the IP camera to a hub or a switch for integration with the network
b. Power the device; for the procedure, see page 9.
2. For an S1970e device with PoE, connect the injector to the device to provide power and
Ethernet connectivity; for the procedure, see page 10.
Warning: Never use PoE and 12V DC at the same time; otherwise you may damage the
device.
3. On a transmitter, plug the video cable of the camera to the video BNC connector of the
device.
4. On a receiver, plug the video cable of the monitor to the video BNC connector of the
device.
5. If required, connect the serial port of the S1900e to the target device (see next).

Performing Serial Connections

The S1900e device supports only the RS-422 and RS-485 asynchronous protocols. For any other protocol, you may need a converter.
Most target devices (keyboards, PTZ cameras, monitors) use the RS-422/485 protocol for communication.
To use the RS-422/485 functionality, you need to:
1. Connect a twisted pair cable to the multipin connector on the front of the device. The
connector gives access to the Tx+, Tx-, Rx+, Rx-, and ground signals.
2. Select the right operating mode (RS-422 4 wires, RS-485 2 wires, or RS-485 4 wires)
using SConfigurator or a video management software.
11 Verint Video Intelligence Solutions
Nextiva S1900e Series User Guide
Tx+
Tx-
Rx+
Rx-
Tx+
Tx-
Rx-
Rx+
Tx+
Tx-
Rx+
Rx-
Nextiva device Peripheral
Data +
Tx+
Tx-
Rx+
Rx-
Tx+
Tx-
Rx+
Rx-
Data -
Nextiva device Peripheral
To properly make the connection to a four-wire RS-422 or RS-485 serial device, use the following scheme (where the Tx signals are for input and the Rx signals are for output):
Signal on Peripheral Signal on S1900e
Tx+ Tx+ Tx- Tx­Rx+ Rx+ Rx- Rx­ground ground
Note: On some equipment, signal terminology may vary. Refer to the peripheral
documentation to find the equivalent terms.
The resulting four-wire configuration is:
For a two-wire RS-485 connection with a Nextiva device:
1. Create the Data- signal by shorting the Rx- and Tx- pins together.
2. Create the Data+ signal by shorting the Rx+ and Tx+ pins together.
Verint Video Intelligence Solutions 12
2: Configuring and Installing the Device
3. Use the following wiring scheme:
Signal on Peripheral Signal on S1900e
Data+ Data+ Data- Data­ground ground

Configuring the Device

The configuration steps to execute are:
Setting a series of parameters, including the IP address Establishing a point-to-point connection between the S1900e and a receiver, if required
Device configuration requires the use of the proprietary SConfigurator tool. Its late st version is included on the Verint web site (www.verint.com/manuals executable file (SConfigurator.exe) to the hard disk of your computer.
The minimum hardware and software requirements for the host computer needed to configure the edge device are:
). You need to copy its
An Ethernet network card Internet Explorer 6.0 or higher Microsoft DirectX 8.1 or higher Windows 2000 Service Pack 2 or higher, or Windows X P Service Pack 2 or higher

Setting Network Parameters

c
The first step in configuring an S1900e device is to provide a typical initial configuration of its network parameters (including its IP address) to ensure compatibility with an existing network.
Note: To work properly, devices on the same network must have un ique IP addresses. The
device will not prevent you from entering a duplicate address. However, its system status LED will turn to flashing red (1-second interval); then the device will use its default address. You then need to configure it with a proper IP address.
After providing the network settings, you complete the configuration with SConfigurator, the web interface, or your video management software.
To set the network parameters of a device:
1. Ensure that the S1900e is powered and connected to the network.
2. Start SConfigurator by double-clicking SConfigurator.exe on your hard disk. The
SConfigurator window appears.
13 Verint Video Intelligence Solutions
Nextiva S1900e Series User Guide
3. In the General tab, click Program Options. The Program Options window appears.
4. Check Detect All Units on LAN.
5. Ensure that the VSIP Port is 5510; otherwise, click Default.
6. Ensure that the Discovery IP Address is 255.255.255.255; otherwise, click Reset to
Broadcast.
7. Click OK.
8. Select the Units tab, then click Discover.
A device of type “Unknown” with a 169.254.X.Y IP address appears in the list; it
corresponds to your new device. This default IP address is based on the APIPA
(Automatic Private IP Addressing) addressing scheme.
X and Y are relative to the MAC
(Media Access Control) address of the device; for more information about APIPA, see
page 69.
9. Select the unknown device, then click Configure.
Verint Video Intelligence Solutions 14
2: Configuring and Installing the Device
Transmitter Receiver
10. In the Reconfigure unit? confirmation window, click Yes. The New Network
Configuration window appears.
11. If you have a DHCP (Dynamic Host Configuration Protocol) server on your network,
check Use DHCP. Otherwise, enter the IP addr ess, subnet mask, and gateway of the
device, as provided by your network administrator. For more information about DHCP,
see page 69.
12. Click OK. The device reboots with its new network configuration. This may take up to
20 seconds.
13. In the Units tab, click Discover to update the list of devices. The new S1900e device
appears.
14. Select the device, then click Configure.
15. Configure the serial port parameters to match those of the target equipment (for
instance, camera or PTZ keyboard).
For more information, refer to the Verint SConfigurator User Guide. The S1900e initial configuration is now complete. You perform further configuration with
the web interface (see page 21), SConfigurator, or your video management software.

Performing a Point-to-Point Connection

A point-to-point connection is the association of a transmitter and a receiver to view video coming from an analog camera on an analog monitor. The Nextiva receivers are the S1970e-R and S1504e-R. You can connect each of these receivers to up to four transmitters, to create a maximum of four different point-to-point connections. Here is a single connection:
You can also use a point-to-point connection to transfer audio, input/output, or serial port data, if the transmitter and receiver have these features.
15 Verint Video Intelligence Solutions
Nextiva S1900e Series User Guide
Typically, both devices sit on the same IP subnet as SConfigurator and have the same VSIP port; to access other devices, refer to the device discovery section in the Verint SConfigurator User Guide.
To associate a transmitter and a receiver in a point-to-point connection:
1. Start SConfigurator.
2. In the Units tab, discover the desired devices. The discovered devices appear in the
Units box.
3. Select the Connections tab, then click Add. The Connection Creator window appears.
4. Select a transmitter in the left column and a receiver in the right one.
In the Transmitters column, you have access to the two encoders of each input; the
video stream is the same for both. Encoder1 is always reserved for viewing live video
with the web interface, therefore you should use Encoder2 for point-to-point
connections; however, you can use the same encoder for both functions if you want the
same resolution and frame rate.
5. In the Video list, select the desired transmission mode for video data. The available
values are:
RTP/UDP—A video mode using RTP (Real Time Transport Protocol, RFC 3550) over
UDP. It is the preferred mode for LAN environments; however, it does not guarantee proper reception of packets. (default)
VSIP/UDP—A legacy mode, using the proprietary VSIP video protocol over UDP. The
preferred UDP mode is RTP/UDP.
RTP/TCP—A video mode using RTP (Real Time Transport Protocol, RFC 3550) over
TCP. It can be useful over WANs, Internet, or LANs needing more robust or secure connections. This mode guarantees proper reception of packets, but could slow down the effective frame rate to a level which is not acceptable.
VSIP/TCP—A legacy mode, using the proprietary VSIP video protocol over TCP. The
preferred TCP mode is RTP/TCP.
6. If you are not transferring I/O data (typically alarms) between the two selected
devices, clear Forward I/O.
7. If you are not transferring serial port data (like PTZ commands), clear Forward Serial
Port Data.
Verint Video Intelligence Solutions 16
2: Configuring and Installing the Device
8. T o enable audio between the devices, ensure that Enable Audio is checked, then select
the audio mode. The available modes are:
Full Duplex—Audio data is transferred in both directions simultaneously.
PTT/PTL—Push-to-talk/push-to-listen is a half-duplex mode that allows you to
control audio communication by using a button to switch from voice reception to transmission mode. Audio data will be transmitted only if the PTT or PTL buttons are pressed.
Note: On a receiver, you can activate audio on a single connection only. The active
audio connection is the last that was performed. The audio connection will remain the same even if the S1970e-R is in guard tour
mode, that is, the receiver will not switch between the audio streams of its four connected transmitters. For more information, see page 39.
9. Click Connect.
10. In the SConfigurator confirmation window, click OK.
You should now have video on the analog monitor connected to the receiver. Audio, I/O, and serial port data can also be transferred.
c

Configuring the I/Os

7
The input/output features on the multipin connector on the back of the device are used for alarms (or events) and audio control. The device includes one input contact and one output relay. Their dedicated purpose is:
Input contact —Either transparent alarm link with the output relay or PTT (push -to-talk)
audio transmission mode Output relay—Relay for the input signal of the remote device
You can program PTT and an alarm on the first input at the same time. The relay of the remote device will be closed and PTT will be activated.
Since the S1900e devices are mostly used with a video management software, you will perform most configuration and activation steps within it. Otherwise, in a point-to-point context, use SConfigurator for setup.
17 Verint Video Intelligence Solutions
Nextiva S1900e Series User Guide
Ground Input
Relay Relay
-T -R

Alarms

The S1900e devices can generate and receive alarms. In a typical configuration, you plug an event sensor to the input and ground I/O pins on a transmitter, and your alarm system to the two output relay pins of a receiver. For example:
With SConfigurator, you activate the alarm process by checking the Forward I/O box in the Connection Creator window.

Audio

The audio connectors are the 3.5 mm jacks on the back of the device; Appendix C on page 71 presents the jack pinouts.
To activate audio between a transmitter and a receiver, both devices must support audio.
Data Transmission
Two transmission modes for audio data are available:
Full duplex—Data is transferred in both directions simultaneously. PTT—The push-to-talk mode allows you to control audio communication between two
devices by pushing a button to transmit. When creating a point-to-point connection between a receiver and a transmitter in
SConfigurator, you set the transmission mode in the Connection Creator window. To activate the audio transmission channel for PTT on the S1900e device, you must trigger
an activation switch (for example, a button) that is based on the shorting of the ground and input pins.
Verint Video Intelligence Solutions 18
2: Configuring and Installing the Device
-R
PTT
Gnd In
PTT
Audio out Audio in
Audio out
Audio in
-T
Gnd In
Audio In
Pre-amp.
Line-out
Audio In
Audio Out
Here is a typical PTT application in a point-to-point context:
Audio Input/Output Types
The device supports the following audio input types: Line-in—To use a 3.5 mm jack (default). In this mode, you need a pre-amplifier. You
connect the audio input on the device to the Line-out connector on the pre-amplifier.
Mic (with pre-amp)—To use a multimedia microphone (Electret). Most multimedia
microphones use a 3.5 mm jack. You connect the microphone directly in the audio input
of the device.
With SConfigurator, you set the input type in the Audio > Encoder pane. The device supports the following audio output types: Speaker—You plug a speaker directly on the audio output of the device.
19 Verint Video Intelligence Solutions
Nextiva S1900e Series User Guide
Audio Out
Amp.
Line-in
Audio Out
Line-out with an amplifier and a speaker.
Line-out with headphones, without the need of an amplifier.
In the Audio > Decoder pane of the SConfigurator tool, you can set one output setting, the output gain (volume).
Specifications
The audio input/output specifications are (where 0 dBV = 1 Vrms):
Mode Gain Impedance Frequency Range
Mic -38 to -21 dBV 30 kohm Line-in -20 to -3 dBV 30 kohm
300–3600 Hz
Speaker -45 to -3 dBV 8 ohms minimum Line-out -45 to -3 dBV 16 ohms minimum
The audio resolution is 16 bits per sample before the compression. The sampling rate is 8KHz.
The resulting bit rate varies depending on the compression mode:
Compression Mode Resulting Bit Rate
PCM (no compression) 128 kbits/s uLaw 64 kbits/s GSM 13 kbits/s
Verint Video Intelligence Solutions 20

Using the Web Interface

In addition to SConfigurator, another tool is available to interact with the device: the web interface. The web interface allows you to:
View a quick status of the device Configure the device View live video and control a PTZ camera Perform maintenance operations
The web interface is only available with Microsoft Internet Explorer 6.0 or later. You may have to install or upgrade ActiveX controls when accessing the web interface for the first time or after updating your device from a previous firmware release.
Depending on user account and security settings, you may have to provide a user name and password when logging into the web interface or accessing it in secure mode. For more information, see the Security parameters on page 29.
Verint Video Intelligence Solutions 21
Nextiva S1900e Series User Guide
Navigation pane

Installing or Upgrading ActiveX Controls

The first time you access the web interface or after updating your device from a previous firmware release, you need to install or upgrade the ActiveX controls for live viewing and firmware update.
To install or upgrade the ActiveX controls:
1. Open a Microsoft Internet Explorer window.
2. Select Tools > Pop-up Blocker > Turn Off Pop-up Blocker.
3. If you upgraded the firmware of the device:
a. Select Tools > Internet Options.
b. In the Temporary Internet files box of the General tab, click Delete Files.
c. In the Delete Files window, check Delete all offline conte n t, then click OK.
d. In the C:\Windows\Downloaded Program Files folder on your computer, delete the
SnPlayer Control and FwuEngineAx Class files.
4. In the Address box, enter the IP address of the device using the http://IP_address
format.
5. Select Tools > Internet Options > Security to lower the security level in your web
browser to enable the ActiveX components to install. Select Trusted sites, then click
Sites to add the IP address of the device in the trusted sites list.
Verint Video Intelligence Solutions 22
3: Using the Web Interface
6. In the navigation pane, click Live Video. A yellow information bar appears below the
Address box.
7. Click the information bar.
8. In the contextual window that appears, select Install ActiveX Control.
9. If your environment is Windows XP Service Pack 2 with Internet Explorer 6, click Live
Video again in the navigation pane of the web interface.
10. In the Internet Explorer - Security Warning window, click Install.
The ActiveX is installed. You can now see live video.
11. If you do not see live video, clear the Enable YUV Support box (see page 55).
12. In the navigation pane, click Maintenance; then in the Maintenance pane, click
Update. A yellow information bar appears below the Address box.
13. Click the information bar.
14. In the contextual window that appears, select Install ActiveX Control.
15. If your environment is Windows XP Service Pack 2 with Internet Explorer 6, click
Maintenance in the navigation pane, then the Update button.
16. In the Internet Explorer - Security Warning window, click Install.
The ActiveX is installed.
17. Select Tools > Pop-up Blocker > Turn On Pop-up Blocker.
23 Verint Video Intelligence Solutions
Nextiva S1900e Series User Guide
Navigation pane
Main pane
Product type Device name IP address
Firmware version
Uptime

Viewing the Quick Status

The Quick Status pane presents a summary of the device. It is the default view when you access the web interface. You may need to provide some of these internal parameters to customer service specialists for troubleshooting purposes. For a more complete view of internal parameters, look at the system status (described on page page 31).
To access the web interface:
1. Open a Microsoft Internet Explorer window.
2. In the Address box, enter the IP address of the device using the http://IP_address
format. The web interface window appears.
The web interface is composed of the following graphical elements:
Product type—The type of the device.
Device name—The descriptive name of the device. Go to page 44 to change it.
IP address—The IP address of the device.
Navigation pane—The types of information that are available in the web interface.
Main pane—The area where to configure the device, view data, and perform
maintenance tasks.
Firmware version—The current firmware version of the main processor of the
device. The latest firmware files are available on the Verint Video Intellige nc e Solutions extranet.
Verint Video Intelligence Solutions 24
3: Using the Web Interface
Uptime—The time since the device has been rebooted, using the following format:
x days hh:mm:ss; the “days” portion does not appear if the uptime is less than one day. The uptime is not automatically refreshed; press F5 to update it.
To view the quick status of the device:
1. In the navigation pane, click Quick Status. Basic information appear in the main pane.
The quick status information contains:
Device Type—The type of the device. This information is also displayed on the top
banner of the web interface.
Serial Number—The serial number of the device.
Build Date—The date the firmware has been generated.
Firmware Version—The current firmware version of the device. This information is
also displayed on the bottom banner of the web interface.
Uptime—The time since the device has been rebooted. This information is also
displayed on the bottom banner of the web interface.
IP—The IP address of the device. This information is also displayed on the top
banner of the web interface.
Memory—The available internal memory in the device.
25 Verint Video Intelligence Solutions
Nextiva S1900e Series User Guide

Configuring the Device

The following parameter categories are available for configuration on the device:
Serial port VSIP Access management Audio System status On-screen display (on the S1970e-R only) Network System time Video HTTP (Webserver) Video status

Configuring the Serial Port

The device has one serial port, RS-422/485, for communicating with serial equipment (for example, PTZ cameras). For more information about the serial port settings of the specific product with which you want to interface, refer to its user guide or contact your product manufacturer.
To configure the serial port:
1. In the navigation pane, expand Configuration, then click Serial Port. The serial port
parameters appear.
2. In the Bit Rate box, enter the transmission speed of the target equipment. Possible
values range from 1200 to 230,400 bits per second (for a transmitter) or to
115,200 bits per second (for a receiver).
3. In the Parity list, select the parity check. Parity is used for error detection. Possible
values are Odd, Even, or None.
Verint Video Intelligence Solutions 26
3: Using the Web Interface
4. In the RS-422/485 Operating Mode list, select the way the RS-422/485 equipment
will interface with the device. Possible values are RS-422 4 Wires, RS-485 4 Wires, and
RS-485 2 Wires.
5. In the Stop Bits list, select the number of stop bits in each transmission. Possible
values are 1 or 2 bits.
6. In the Data Bits list, select the number of bits in transmitted data. Possible values are
7 or 8 bits.
7. To continue the configuration process, select another parameter category in the
navigation pane. Otherwise, click Apply to save the changes in the device. Depending
on the changes you made, a reboot may be required; follow the on-screen instructions
in the Device Configuration Submittal pane.

Configuring Access Management

Access management takes care of user accounts and device security.
User Accounts
You can set up user accounts to protect the configuration of the device by restricting its access with a user name and a password. Once the user account mode is activated, you need the user name/password combination to access the command line interface (CLI) of the device and the web interface.
Two types of users are available: Administrator—Has all rights and is automatically available when user accounts are
activated. Web client—Only has access to live video and quick status in the web interface. Five
web clients are available.
27 Verint Video Intelligence Solutions
Nextiva S1900e Series User Guide
To configure the user accounts:
1. In the navigation pane, expand Configuration > Access Management, then click
User Accounts. The user account parameters appear.
2. In the User Accounts list, indicate whether the use of user names and passwords to
access the device with the web interface or the command line interface is enabled. If
disabled (default), anybody can access the device. This parameter applies to the
S1950e, S1970e, and S1970e-R only.
3. In the Administrator User Name box, enter the alphanumeric string identifying the
administrator user.
4. In the Administrator Password box, enter the alphanumeric string protecting the
access to the device for the administrator user.
5. In the Web Client x User Name box, enter the alphanumeric string identifying a web
client user.
6. In the Web Client x Password box, enter the alphanumeric string protecting the
access to the device for a web client user.
7. In the Web Client x list, indicate whether the web client number x is enabled. This
parameter applies to the S1900e-AS only.
8. If required, repeat the web client configuration steps for all web client users. Up to five
web clients are available.
9. To continue the configuration process, select another parameter category in the
navigation pane. Otherwise, click Apply to save the changes in the device. Depending
on the changes you made, a reboot may be required; follow the on-screen instructions
in the Device Configuration Submittal pane.
Verint Video Intelligence Solutions 28
3: Using the Web Interface
Security
The security parameters are relative to the protection of the device.
To configure the security parameters:
1. In the navigation pane, expand Configuration > Access Management, then click
Security . The security parameters appear. The parameters for the S1950e, S1970e,
and S1970e-R are:
The parameters for the S1900e-AS are:
2. In the Telnet Session list, indicate whether the access to the CLI of the device with
Telnet is enabled.
29 Verint Video Intelligence Solutions
Nextiva S1900e Series User Guide
3. In the Use Telnet Accounts list, indicate whether the use of user accounts to access
the device with the CLI is enabled. This parameter applies to the S1900e-AS only. To
define user accounts, see page 27.
4. In the XML Report Generation list, indicate whether the generation of an XML report
presenting the current state of the device is enabled.
5. In the IP Firmware Update list, indicate whether firmware updates on the device
through the IP network are enabled.
6. In the HTTP Access list, indicate whether the access to the web interface of the device
in a non-secure context is enabled. If you block this access, you can only set up the
device with SConfigurator or Telnet.
7. In the Secure HTTP Access list, indicate whether the access to the web interface of
the device in a secure SSL context is enabled. This parameter applies to the S1950e,
S1970e, and S1970e-R only. If this context is enabled, you access the device with
https://IP-address in your web browser and the user account mode is automatically
activated (described on page 27).
8. In the HTTPS Access list, indicates whether the access to the web interface of the
device in a secure HTTP (HTTPS) context is enabled. This parameter applies to the
S1900e-AS only.
9. In the Use Web Client Accounts list, indicate whether the use of user accounts to
access the device with the web interface is enabled. This parameter applies to the
S1900e-AS only. To define user accounts, see page 27.
10. In the Global Security Profile list, indicate whether the complete SSL security on the
device is enabled. Once this profile is activated on a device:
You cannot access it anymore with Telnet.
You cannot perform firmware updates through the IP network.
You access its web interface in a secure mode (that is, the secure HTTP access
mode is enabled).
11. In the SSL Passkey box, enter a password to secure the connection with the device.
The passkey must be the same for all devices and the software tools to allow proper
secure communication between them.
Tip: You should not change this passkey with the web interface, since there could be
eavesdropping on the network. You can use SConfigurator or a video management software to change it.
12. To continue the configuration process, select another parameter category in the
navigation pane. Otherwise, click Apply to save the changes in the device. Depending
on the changes you made, a reboot may be required; follow the on-screen instructions
in the Device Configuration Submittal pane.
Verint Video Intelligence Solutions 30
3: Using the Web Interface

Viewing the System Status

The system status information indicates the current values of internal device parameters. These internal parameters are useful when troubleshooting the device with the assistance of a customer service specialist.
To view the system status of the device:
1. In the navigation pane, expand Configuration, then click System Status. The system
status parameters appear.
The following information is available:
Firmware Version—The current firmware version of the main processor of the
device. The latest firmware files are available on the Verint Video Intellige nc e Solutions extranet.
Loader Version—The version of the firmware used to load the device.
Booter Version—The version of the firmware used to boot the device.
PIC Firmware Version— The v ersion of the firmw are used in the PIC (programmable
intelligent controller) microcontroller.
Build Date—The date the firmware has been generated.
CPU Info—The version of the processing unit in the device.
CPU Frequency—The frequency (in Hz) of the processing unit in the device.
Uptime—The time since the device has been rebooted.
Serial Number—The serial number of the device.
CPLD Version—The version of the complex programmable logic device.
Board Version—The version of the main board in the device.
31 Verint Video Intelligence Solutions
Nextiva S1900e Series User Guide
Internal Value 1—Verint technical information.
Audio Hardware—The indication of whether audio hardware is present on the
device.
Unit Tested (MM-YY)—The date the device was tested by Verint production.
Board Temperature—The temperature of the main board (in degrees Celcius).

Configuring the Network

The network parameters allow communication between the device and its IP network. For more information about these settings, contact your network administrator.
To configure the network parameters:
1. In the navigation pane, expand Configuration, then click Network. The network
parameters appear.
2. In the DHCP Configuration list, indicate whether DHCP (Dynamic Host Configuration
Protocol) is used to automatically provide a valid network configuration for the device.
You can set this option only if the device is connected to a network that uses a DHCP
server. For more information about DHCP, see Appendix B on page 69.
3. In the Local IP Address box, enter the unique IP address of the device on the
network. The IP address is written as four numbers separated by periods; each number
is in the 0–255 range. Each device on a network must have a unique IP address.
4. In the Subnet Mask box, enter the binary configuration that specifies the subnet in
which the IP address of the device belongs. A subnet is a portion of a network that
shares a common address component. Unless otherwise specified by your network
administrator, it is recommended to use a subnet mask of 255.255.0.0.
5. In the Gateway box, enter the IP address of the network point that acts as an entrance
to another network. Never use the IP address of the device as the gateway value.
Verint Video Intelligence Solutions 32
3: Using the Web Interface
6. In the Host Name box, enter an alias for the IP address of the device, to be used by
the DNS server; this parameter is optional. It is made up of 2 to 24 alphanumerical
characters; the first one must be a character.
Note: It is up to the DHCP server to register the host name in the DNS server.
7. To continue the configuration process, select another parameter category in the
navigation pane. Otherwise, click Apply to save the changes in the device. Depending
on the changes you made, a reboot may be required; follow the on-screen instructions
in the Device Configuration Submittal pane.

Configuring Video

The following aspects of the video functions of the device are available for configuration:
General parameters for transmitters Encoder General parameters for receivers Decoder
General Parameters for Transmitters
Some parameters are common to all video functions of the transmitter.
To configure the general video parameters of the device:
1. In the navigation pane, expand Configuration > Advanced, then click Video.
33 Verint Video Intelligence Solutions
Nextiva S1900e Series User Guide
2. In the Video Standard list, select the analog display standard. Possible values are:
NTSC—Used in North America, Central America, a number of South American
countries, and some Asian countries, including Japan.
PAL—Used in United Kingdom, much of western Europe, several South American
countries, some Middle East and Asian countries, several African countries, Australia, New Zealand, and other Pacific island countries.
3. In the Brightness box, enter the total amount of light in a color.
4. In the Contrast box, enter the range of colors in the image.
5. In the Saturation box, enter the intensity of the colors in the image.
6. In the Hue box, enter the relative amounts of red, green, and blue in a color.
7. In the Frame Format list, select the way the video is compressed. This parameter
applies to the S1950e and S1970e only. The available values are:
Field over Field—The proprietary mode used by the Nextiva edge devices.
Interlaced Frame—The MPEG-4 compliant mode where the two video fields are
interlaced.
Deinterlaced Frame—The MPEG-4 compliant mode where the two video fields are
converted to a progressive scan image by a deinterlacing filter. This filter removes interlaced artifacts for playback on a progressive scan monitor.
8. In the Number of Encoders per Video Input box, enter the number of encoders
receiving a video stream. This parameter applies to the S1950e only. Typically you use
both encoders for video; however, to activate the noise reduction filter (see page 36),
you need to disable the second encoder. The available values are:
1—To use Encoder 1 for video with the noise reduction filter set at Low.
2—To use both encoders for video.
9. To continue the configuration process, select another parameter category in the
navigation pane. Otherwise, click Apply to save the changes in the device. Depending
on the changes you made, a reboot may be required; follow the on-screen instructions
in the Device Configuration Submittal pane.
Encoder
The video parameters are the same for the two encoders in the device. However, they v ary depending on the compression mode: There is one set of parameters for the SM4 and MPEG4 Compliant Simple Profile modes, and another one for MJPEG.
To configure the encoder parameters for the SM4 or MPEG4 Compliant Simple Profile compression mode:
1. In the navigation pane, expand Configuration > Advanced > Video, then click the
desired Encoder.
2. In the Compression Mode box, select SM4 or MPEG4 Compliant Simple Profile. The
compression mode represents the way the video is compressed. The following codecs
(coders/decoders) are available:
SM4—The proprietary MPEG-4-based mode.
MPEG4 Compliant Simple Profile—The MPEG-4 ISO 14496-2 compliant mode.
Verint Video Intelligence Solutions 34
3: Using the Web Interface
Compression mode
MJPEG—The Motion JPEG mode that uses standard JPEG still images.
3. If the previous compression mode was MJPEG, click Apply to save the changes and see
the SM4 or MPEG4 Compliant Simple Profile parameters.
The SM4 or MPEG4 Compliant Simple Profile parameters appear.
4. In the Target Bit Rate box, enter the maximum number of kilobits per second that
you want the device to generate. V alid target bit rates r ange from 9 to 6000 kilobits per
second.
5. In the Target Frame Rate box, enter the maximum number of frames per second
(fps) that will be encoded and transferred by the transmitter. This parameter can be set
to 1 to 7, 10, 15, or 30 fps in NTSC mode and 1 to 6, 8, 12, or 25 fps in PAL mode.
6. In the Minimum Quantizer box, enter the high video quality boundary. The lower the
value, the higher the video quality and the file size. The value range is from 2 to 31.
7. In the Maximum Quantizer box, enter the low video quality boundary. A higher
quantizer value means less video quality but a smaller file size. The value range is from
2 to 31.
8. In the Input Filter Mode list, select the level of filtering applied to the video signal
before it is encoded, helping to remove high frequency noise from lower quality
cameras or noisy video feeds. The available values are Low, Medium, High, or None.
35 Verint Video Intelligence Solutions
Nextiva S1900e Series User Guide
9. In the Noise Reduction Filter Mode list, select the filtering of small variations in
pixels in otherwise motionless sections of the video, to be used in all conditions to
reduce the bit rate. Using this filter also helps reduce the number of false alarms in low
light conditions. To see this parameter on the S1950e, you need to deactivate the
second video encoder (see page 34). The available values are Low (default), Medium,
High, and None.
10. In the Resolution list, select the measure of how clear and crisp the video image
appears. Each resolution corresponds to a specific number of pixels (columns * lines)
for each picture of the video sequence. The available resolutions are: QCIF, CIF, 2CIF,
4CIF, All lines, 2/3 D1, and VGA.
11. In the Rate Control Mode list, select the mode controlling the bit rate variation. The
available modes are:
CFR (Constant Frame Rate)—This mode maintains the target frame rate. Video
quality may suffer and the bit rate may exceed the target value.
CBR (Constant Bitrate)—This mode is the most effective to maintain the target bit
rate. Video quality may suffer (frames may be skippe d) and the frame rate may decrease. This mode should be used when transmitting video over networks that have very limited bandwidths, and with an intra-interval value of 0.
CSR (Constant Storage Rate)—This is the optimized mode, based on CBR, to be
used for the Nextiva enterprise video management software to make good use of the storage capacity. This parameter applies to the S1900e-AS only.
CNR (Constant Nextiva Rate)—This is the optimized mode, based on CBR, to be
used for the Nextiva enterprise video management software to make good use of the storage capacity. This parameter applies to the S1950e and S1970e only.
12. In the Web Multicast IP Address box, enter the IP address of the multicast group
from which the web interface will get live video, if the web streaming method is
Multicast UDP (see page 52).
13. In the Web Multicast IP Port box, enter the IP port of the multicast group from which
the web interface will get live video, if the web streaming method is Multicast UDP (see
page 52).
14. In the Intra Interval box, enter the frequency at which a complete video frame (called
I-frame) is sent by the encoder. The available values are in the 0–1000 range. A value
of X means that a complete image refresh will occur every X frames.
Tip: It is not recommended to use a value of 0.
15. In the Frame Format list, select the way the video fields are compressed. This
parameter applies to the S1900e-AS only. The available values are:
Field over Field—The proprietary mode used by the Nextiva edge devices.
Interlaced Frame—The MPEG-4 compliant mode where the two video fields are
interlaced.
Deinterlaced Frame—The MPEG-4 compliant mode where the two video fields are
converted to a progressive scan image by a deinterlacing filter. This filter removes interlaced artifacts for playback on a progressive scan monitor.
Verint Video Intelligence Solutions 36
3: Using the Web Interface
16. To continue the configuration process, select another parameter category in the
navigation pane. Otherwise, click Apply to save the changes in the device. Depending
on the changes you made, a reboot may be required; follow the on-screen instructions
in the Device Configuration Submittal pane.
To configure the encoder parameters for the MJPEG compression mode:
Note: On the S1900e-AS, MJPEG is only available on the first encoder.
1. In the navigation pane, expand Configuration > Advanced > Video, then click the
desired Encoder.
2. In the Compression Mode box, select MJPEG. The compression mode represents the
way the video is compressed. The following codecs (coders/decoders) are available:
SM4—The proprietary MPEG-4-based mode.
MPEG4 Compliant Simple Profile—The MPEG-4 ISO 14496-2 compliant mode.
MJPEG—The Motion JPEG mode that uses standard JPEG still images.
3. Click Apply to save the changes and see the MJPEG parameters.
The MJPEG parameters appear.
4. In the Target Frame Rate box, enter the maximum number of frames per second
(fps) that will be encoded and transferred by the transmitter. This parameter can be set
to 1 to 7, 10, 15, or 30 fps in NTSC mode and 1 to 6, 8, 12, or 25 fps in PAL mode.
5. In the Input Filter Mode list, select the level of filtering applied to the video signal
before it is encoded, helping to remove high frequency noise from lower quality
cameras or noisy video feeds. The available values are Low, Medium, High, or None.
37 Verint Video Intelligence Solutions
Nextiva S1900e Series User Guide
6. In the Noise Reduction Filter Mode list, select the filtering of small variations in
pixels in otherwise motionless sections of the video, to be used in all conditions to
reduce the bit rate. Using this filter also helps reduce the number of false alarms in low
light conditions. To see this parameter on the S1950e, you need to deactivate the
second video encoder (see page 34). The available values are Low (default), Medium,
High, and None.
7. In the Resolution list, select the measure of how clear and crisp the video image
appears. Each resolution corresponds to a specific number of pixels (columns * lines)
for each picture of the video sequence. The available resolutions are: QCIF, CIF, 2CIF,
4CIF, All lines, 2/3 D1, and VGA.
8. In the Web Multicast IP Address box, enter the IP address of the multicast group
from which the web interface will get live video, if the web streaming method is
Multicast UDP (see page 52).
9. In the Web Multicast IP Port box, enter the IP port of the multicast group from which
the web interface will get live video, if the web streaming method is Multicast UDP (see
page 52).
10. In the Frame Format list, select the way the video fields are compressed. This
parameter applies to the S1900e-AS only. The available values are:
Field over Field—The proprietary mode used by the Nextiva edge devices.
Interlaced Frame—The MPEG-4 compliant mode where the two video fields are
interlaced.
Deinterlaced Frame—The MPEG-4 compliant mode where the two video fields are
converted to a progressive scan image by a deinterlacing filter. This filter removes interlaced artifacts for playback on a progressive scan monitor.
11. In the Rate Control Mode list, select the mode controlling the file size variation. The
available modes are:
CFS (Constant File Size)—The quality of the images may vary, but their size will be
targeted to the value specified by the Target File Size parameter.
VFS (Variable File Size)—The quality of the image is set by the Variable File Size
Quality parameter, but the size of the image will vary, depending of the encoded image.
12. In the Target File Size box, enter the target size of each image that will be encoded
(in Kbytes), if the rate control mode is CFS. The available values are in the 1–100
range.
13. In the Variable File Size Quality list, select the quality of the encoded images, if the
rate control mode is VFS. The value range is from VFS1 (high quality) to VFS7 (worst
quality).
14. To continue the configuration process, select another parameter category in the
navigation pane. Otherwise, click Apply to save the changes in the device. Depending
on the changes you made, a reboot may be required; follow the on-screen instructions
in the Device Configuration Submittal pane.
Verint Video Intelligence Solutions 38
3: Using the Web Interface
General Parameters for Receivers
On an S1970e-R, the video parameters can appear in a single page or in up to five pages, depending on the value of the Receiver Mode parameter. The receiver mode indicates what is displayed on the analog monitor connected to the receiver; the available values are:
Solo—The monitor displays the video stream coming from a unique transmitter
(default). Quad—T he monitor is split into four quadrants and displays at the same time four video
streams coming from four transmitters. Guard Tour—The monitor displays four video streams one at a time in a cycling mode. In the Solo mode, all video parameters are located in a single page. In the other two
modes, the parameters common to all the video functions of the receiver are presented in the Video page; the parameters for each of the four decoders are displayed in a separate Decoder page (see page 42).
To change the receiver mode of an S1970e-R:
1. In the navigation pane, expand Configuration > Advanced, then click Video. The
video parameters appear.
2. In the Receiver Mode box, indicate what is displayed on the monitor connected to the
S1970e-R. The available values are:
Solo—The monitor displays the video stream coming from a unique transmitter
(default).
Quad—The monitor is split into four quadrants and displays at the same time four
video streams coming from four transmitters.
39 Verint Video Intelligence Solutions
Nextiva S1900e Series User Guide
Guard Tour—The monitor displays four video streams one at a time in a cycling
mode.
Note: When changing the mode from Solo to Quad or Guard Tour (or vice versa), you
need to reboot the device for the modification to take effect. The point-to-point connections between the S1970e-R and the four transmitters
are established with SConfigurator (for more information, see page 15).
3. To continue the configuration process, select another parameter category in the
navigation pane. Otherwise, click Apply to save the changes in the device. Depending
on the changes you made, a reboot may be required; follow the on-screen instructions
in the Device Configuration Submittal pane.
To change the general video parameters of an S1970e-R in Solo mode:
1. In the navigation pane, expand Configuration > Advanced, then click Video. The
video parameters appear.
2. In the Video Standard list, select the analog display standard. The available values
are:
NTSC—Used in North America, Central America, a number of South American
countries, and some Asian countries, including Japan.
PAL—Used in United Kingdom, much of western Europe, several South American
countries, some Middle East and Asian countries, several African countries, Australia, New Zealand, and other Pacific island countries.
3. In the Deblocking Filter list, indicate whether the filtering of block-shaped artifacts in
the video is enabled. Enable it to remove blocking artifacts; disable it if you are losing
packets while viewing 4CIF video.
Verint Video Intelligence Solutions 40
3: Using the Web Interface
4. In the Brightness box, enter the total amount of light in a color.
5. In the Contrast box, enter the range of colors in the image.
6. In the Saturation box, enter the intensity of the colors in the image.
7. In the Deinterlacing Mode list, indicate whether the deinterlacing filter applied before
video rendering is enabled. This filter removes interlaced artifacts for display at frame
rates under 30 fps in NTSC (25 fps in PAL).
8. In the Wait for I-Frame list, indicate whether the receiver waits for an I-frame before
decoding video.
9. In the Delay Adjustment box, enter the adjustment of the rendering delay v ersus the
rendering fluidity (absence of skipped fr ames). To reduce delay in the video at the cost
of increasing chances of jitter, set this value to 0. To avoid video jitter at the cost of
increasing the delay, set this value to 2. It is recommended to leave this value at 1.
10. To continue the configuration process, select another parameter category in the
navigation pane. Otherwise, click Apply to save the changes in the device. Depending
on the changes you made, a reboot may be required; follow the on-screen instructions
in the Device Configuration Submittal pane.
To change the general video parameters of an S1970e-R in Quad or Guard Tour mode:
1. In the navigation pane, expand Configuration > Advanced, then click Video. The
common video parameters appear.
2. In the Video Standard list, select the analog display standard. The available values
are:
NTSC—Used in North America, Central America, a number of South American
countries, and some Asian countries, including Japan.
41 Verint Video Intelligence Solutions
Nextiva S1900e Series User Guide
PAL—Used in United Kingdom, much of western Europe, several South American
countries, some Middle East and Asian countries, several African countries, Australia, New Zealand, and other Pacific island countries.
3. In the Brightness box, enter the total amount of light in a color.
4. In the Contrast box, enter the range of colors in the image.
5. In the Saturation box, enter the intensity of the colors in the image.
6. In the Guard Tour Dwell Time box, enter the period of time (in seconds) a video
stream will be displayed when the receiver is in Guard Tour mode.
7. To continue the configuration process, select another parameter category in the
navigation pane. Otherwise, click Apply to save the changes in the device. Depending
on the changes you made, a reboot may be required; follow the on-screen instructions
in the Device Configuration Submittal pane.
Decoders
If the Receiver Mode parameter is set to Quad or Guard Tour, specific parameters are available per decoder.
To change the decoder parameters of an S1970e-R in Quad or Guard Tour mode:
1. In the navigation pane, expand Configuration > Advanced > Video, then click the
desired Encoder. The decoder parameters appear.
2. In the Deblocking Filter list, indicate whether the filtering of block-shaped artifacts in
the video is enabled. Enable it to remove blocking artifacts; disable it if you are losing
packets while viewing 4CIF video.
3. In the Wait for I-Frame list, indicate whether the receiver waits for an I-frame before
decoding video.
Verint Video Intelligence Solutions 42
3: Using the Web Interface
4. To continue the configuration process, select another parameter category in the
navigation pane. Otherwise, click Apply to save the changes in the device. Depending
on the changes you made, a reboot may be required; follow the on-screen instructions
in the Device Configuration Submittal pane.

Looking at Video Status

The video status presents the current values of video characteristics for each video encoder or decoder. These internal parameters are useful when troubleshooting the device with the assistance of a customer service specialist.
To see the video status of the device:
1. In the navigation pane, expand Configuration > Advanced > Video Status, then
click the desired encoder or decoder. For an S1970e-R in Solo mode, expand
Configuration > Advanced, then click Video Status. The video status parameters
appear.
The available information is:
Current Frame Rate—The current frame rate of the encoder, in frames per second.
Current Bit Rate—The current number of kilobits per second generated by the
encoder.
Current Quantizer—The current quantizer used by the encoder, multiplied by 100.
Average Frame Rate— The av erage fr ame r ate in the encoder, in frames per second.
It is based on a 2-minute moving average.
Average Bit Rate—The average number of kilobits per second generated by the
encoder. It is based on a 2-minute moving average.
Average Quantizer—The average quantizer, multiplied by 100. It is based on a
2-minute moving average.
Video Input Locked—The indication of whether the input signal is locked.
43 Verint Video Intelligence Solutions
Nextiva S1900e Series User Guide
Video Decoder AGC Value—The automatic gain control value of the video
analog-to-digital converter.

Configuring VSIP

Parameters are available to configure the VSIP proprietary communication protocol.
To configure the VSIP parameters:
1. In the navigation pane, expand Configuration > Advanced, then click VSIP. The
VSIP parameters appear.
2. In the VSIP Port box, enter the communication port used by the device. The default
value of all Nextiva devices is 5510.
Note: VSIP ports 9541, 65500, and those under 1024 are reserved and should not be
used, not even for serial port, video, or audio communication. The maximum value is 65535.
3. In the VSIP Multicast IP Address box, enter the IP address used by the device to
listen for VSIP queries. The current multicast address is 224.16.32.1 and should not be
changed.
4. In the VSIP Discovery IP Address box, enter the IP address used by the device to
make its presence known with the broadcast method. The broadcast address is
255.255.255.255.
5. In the VSIP Unit Name box, enter the name of the device, as displayed in the top of
the web interface and in the first column of the SConfigurator unit list.
6. To continue the configuration process, select another parameter category in the
navigation pane. Otherwise, click Apply to save the changes in the device. Depending
on the changes you made, a reboot may be required; follow the on-screen instructions
in the Device Configuration Submittal pane.
Verint Video Intelligence Solutions 44
3: Using the Web Interface

Configuring Audio

The following aspects of the audio functions of the device are available for configuration:
General parameters Audio input Audio output
To configure the general audio parameters:
1. In the navigation pane, expand Configuration > Advanced, then click Audio. The
general audio parameters appear.
2. In the Audio Mode list, select the audio transmission mode. The available values are:
PTT—A half-duplex mode that allows you to control audio communication between
two devices by using a button to transmit.
Full Duplex—A mode in which is transferred in both directions simultaneously.
The Output Compression parameter presents the transfer mode for the audio data of
the remote device. You cannot change this value.
3. In the Input Compression list, select the transfer mode for converting and
compressing the audio data of the local device. The mode depends on the bandwidth
and desired audio quality. The available values are:
Uncompressed PCM (128 kbps)— There is no audio compression. Audio quality is the
best, at the expense of the bandwidth.
Ulaw (64 kbps)—A North American standard for converting analog data into digital
form using pulse code modulation (PCM).
GSM 6.10 (13 kbps)—The first mobile phone standard. This mode does not work in
the web interface.
4. To continue the configuration process, select another parameter category in the
navigation pane. Otherwise, click Apply to save the changes in the device. Depending
on the changes you made, a reboot may be required; follow the on-screen instructions
in the Device Configuration Submittal pane.
45 Verint Video Intelligence Solutions
Nextiva S1900e Series User Guide
To configure the audio output parameters:
1. In the navigation pane, expand Configuration > Advanced > Audio, then click
Audio Output. The audio output parameters appear.
2. In the Gain box, enter the control for the volume. The available range is from 0 (mute)
to 1000 (loud).
The Overflow parameter is an internal setting that cannot be changed.
3. To continue the configuration process, select another parameter category in the
navigation pane. Otherwise, click Apply to save the changes in the device. Depending
on the changes you made, a reboot may be required; follow the on-screen instructions
in the Device Configuration Submittal pane.
To configure the audio input parameters:
1. In the navigation pane, expand Configuration > Advanced > Audio, then click
Audio Input. The audio input parameters appear.
2. In the Input Type list, select the type of your audio source. The available values are
Line-In and Mic (with pre-amp).
Verint Video Intelligence Solutions 46
3: Using the Web Interface
3. In the Gain box, enter the control for the volume. The available range is from 0 (mute)
to 1000 (loud).
The Overflow parameter is an internal setting that cannot be changed.
4. To continue the configuration process, select another parameter category in the
navigation pane. Otherwise, click Apply to save the changes in the device. Depending
on the changes you made, a reboot may be required; follow the on-screen instructions
in the Device Configuration Submittal pane.

Configuring System Time

The device can connect to a Network Time Protocol (NTP) server to get the current time. The main reason to use NTP is to display valid dates in the log files instead of the device uptime.
The Local Time parameter indicates the current local time if the device is connected to an NTP server.
To configure the system time parameters:
1. In the navigation pane, expand Configuration > Advanced, then click System Time.
The system time parameters appear.
2. In the NTP Server Usage list, indicate whether Network Time Protocol (NTP) is used to
get the current time. NTP uses GMT to synchronize device clock time.
3. In the NTP Server IP Address box, enter the IP address of the NTP server from which
the device will get the current time.
4. In the NTP Server IP Port box, enter the IP port of the NTP server. Default is 123.
5. In the Local Time Offset box, enter the offset in minutes from the GMT time in the
time zone in which the device operates (for instance, the offset for the Eastern
Standard Time is -300 minutes).
47 Verint Video Intelligence Solutions
Nextiva S1900e Series User Guide
12
34
6. To continue the configuration process, select another parameter category in the
navigation pane. Otherwise, click Apply to save the changes in the device. Depending
on the changes you made, a reboot may be required; follow the on-screen instructions
in the Device Configuration Submittal pane.

Configuring On-Screen Display

The on-screen display (OSD) is information to present on top of the video streams, on the analog monitor connected to an S1970e-R receiver.
If the receiver mode (described on page 39) is Solo, all the configuration parameters are on a single page. If the receiver mode is Quad or Guard Tour , fiv e pages are av ailable: one for the parameters common to all decoders and one per decoder.
In Quad mode, you can customize each quadrant on the analog monitor. Quadrant 1 corresponds to decoder 1, and so on for the other quadrants. The quadrant numbering is:
In Guard Tour mode, you can display different on-screen information for each of the four cycling video streams.
To configure the OSD parameters in Solo mode:
1. In the navigation pane, expand Configuration > Advanced, then click On-Screen
Display. The OSD parameters appear.
Verint Video Intelligence Solutions 48
3: Using the Web Interface
2. In the Decoder Starve list, select what is displayed on the monitor when the receiver
is not receiving video. The available values are:
Color bar
Last decoded image
Black
White
Fix color bar
3. In the Display Logo list, indicate whether the Verint logo is displayed in the top right
corner of the monitor for 30 seconds when the receiver is powering up.
4. In the Display Option list, select the information that will be displayed in the bottom
left corner of the monitor. The available values are:
Nothing
Date/time
Uptime
5. In the Display Startup Info list, indicate whether the IP address, name of device, and
firmware version are displayed in the bottom right corner of the monitor for 30 seconds
when the receiver is powering up.
6. In the Show Transmitter Name list, indicate whether the name of the associated
transmitter is displayed above the display option, in the bottom left corner of the
monitor. You provide the name to display in the Transmitter Name parameter.
7. In the Transmitter Name box, enter the name of the transmitter to be displayed when
Show Transmitter Name is enabled.
8. In the Opacity list, select the level of opacity of the information displayed over the
video. A value of 0 indicates that the information is totally transparent (it is not
showing); a value of 255 means that the data covers completely the video.
9. To continue the configuration process, select another parameter category in the
navigation pane. Otherwise, click Apply to save the changes in the device. Depending
on the changes you made, a reboot may be required; follow the on-screen instructions
in the Device Configuration Submittal pane.
49 Verint Video Intelligence Solutions
Nextiva S1900e Series User Guide
To configure the common OSD parameters in Quad or Guard Tour mode:
1. In the navigation pane, expand Configuration > Advanced, then click On-Screen
Display. The common OSD parameters appear.
2. In the Display Logo list, indicate whether the Verint logo is displayed in the top right
corner of the monitor for 30 seconds when the receiver is powering up.
3. In the Display Startup Info list, indicate whether the IP address, name of device, and
firmware version are displayed in the bottom right corner of the monitor for 30 seconds
when the receiver is powering up.
4. In the Opacity list, select the level of opacity of the information displayed over the
video. A value of 0 indicates that the information is totally transparent (it is not
showing); a value of 255 means that the data covers completely the video.
5. To continue the configuration process, select another parameter category in the
navigation pane. Otherwise, click Apply to save the changes in the device. Depending
on the changes you made, a reboot may be required; follow the on-screen instructions
in the Device Configuration Submittal pane.
Verint Video Intelligence Solutions 50
3: Using the Web Interface
To configure the decoder OSD parameters in Quad or Guard Tour mode:
1. In the navigation pane, expand Configuration > Advanced > On-Screen Display,
then click the desired Decoder. The decoder OSD parameters appear.
2. In the Decoder Starve list, select what is displayed on the monitor when the receiver
is not receiving video. The available values are:
Color bar
Last decoded image
Black
White
Fix color bar
3. In the Display Option list, select the information that will be displayed in the bottom
left corner of the monitor (in Guard Tour) or quadrant (in Quad). The information is
refreshed every second. The available values are:
Nothing
Date/time
Uptime
4. In the Show Transmitter Name list, indicate whether the name of the associated
transmitter is displayed above the display option, in the bottom left corner of the
monitor (in Guard Tour) or quadrant (in Quad). You provide the name to display in the
Transmitter Name parameter.
5. In the Transmitter Name box, enter the name of the transmitter to be displayed when
Show Transmitter Name is enabled.
6. To continue the configuration process, select another parameter category in the
navigation pane. Otherwise, click Apply to save the changes in the device. Depending
on the changes you made, a reboot may be required; follow the on-screen instructions
in the Device Configuration Submittal pane.
51 Verint Video Intelligence Solutions
Nextiva S1900e Series User Guide

Configuring HTTP (Webserver)

A series of parameters help configure the communication between the web page on the computer and the device.
To configure the HTTP parameters:
1. In the navigation pane, expand Configuration > Advanced, then click HTTP
(Webserver). The HTTP parameters appear.
Note: If you change any of these parameters, you must refresh the web page (for
instance, by pressing F5).
2. In the HTTP Server IP Port box, enter the TCP port number in the device on which the
HTTP requests will be made. Default in all web applications is 80.
3. In the Web Streaming Method list, select the protocol used for transmitting video.
The available values are:
VSIP/UDP—A legacy protocol, using the proprietary VSIP video protocol over UDP.
The preferred UDP mode is RTP/UDP.
VSIP/TCP—A protocol using the proprietary VSIP video protocol over TCP. This
protocol guarantees proper reception of video packets, but could slow down the effective frame rate to an unacceptable level (default).
Multicast UDP—A protocol using RTP (Real Time T r ansport Protocol, RFC 3550) over
UDP that transfers video to a multicast group. It does not guarantee proper reception of video packets.
RTP/UDP—A protocol using RTP (Real Time Transport Protocol, RFC 3550) over UDP
that transfers video to a unique recipient. It does not guarantee proper reception of video packets.
Verint Video Intelligence Solutions 52
3: Using the Web Interface
4. In the HTTP Audio Streaming list, indicate whether the tr ansmission of audio data is
enabled.
If you enable audio streaming on your computer, you may experience a click every
10 seconds. To stop it, remove the sound with a Control Panel utility: Open Sounds
and Multimedia; in the Sounds tab, locate the Windows Explorer category, then select
Start Navigation; change its sound to (None).
5. In the HTTP PTZ Controls list, indicate whether the transmission of PTZ data is
enabled. You should set this value to Disabled in the following contexts:
If the connected camera does not offer PTZ capabilities.
If you do not want to see PTZ controls displayed in the Live Video Streaming page
(for more information, see page 57).
To disable any movement on a PTZ dome camera.
6. To continue the configuration process, select another parameter category in the
navigation pane. Otherwise, click Apply to save the changes in the device. Depending
on the changes you made, a reboot may be required; follow the on-screen instructions
in the Device Configuration Submittal pane.

Viewing Live Video

The web interface enables you to view the video stream coming from the first encoder of the video source connected to the transmitter.
You can also use PTZ controls to manipulate the camera connected to the device.

Configuring Live Video

Before viewing live video on your computer, you may need to configure some parameters.
Note: If you upgraded the firmw are of the device or are accessing live video for the first
time, you need to install an ActiveX component prior to viewing live video (for more information, see page 22).
To configure live video:
1. Ensure that the camera is properly connected to the device.
53 Verint Video Intelligence Solutions
Nextiva S1900e Series User Guide
Pane separator
2. In the navigation pane, click Live Video. The main web interface pane is split in two,
with the live video portion at the bottom.
Verint Video Intelligence Solutions 54
3: Using the Web Interface
3. If needed, resize the two sub-panes by dragging the separator up or down.
Note: If the Web Streaming Method (described on page 52) is VSIP/TCP, the Local
Video IP Port and Local Audio IP Port boxes do not appear. Unless your setup requires a specific port, it is recommended to keep the
default values in the Local Video IP Port and Local Audio IP Port boxes.
4. In the Local Video IP Port box under Local Settings, enter the port number on your
computer that will receive video.
5. In the Local Audio IP Port box, enter the port number on your computer that will
receive audio.
6. In the Enable YUV Support check box, indicate whether direct YUV rendering will be
performed on the computer; otherwise, RGB is used for video rendering. YUV rendering
is more optimized than the RGB mode. Default is to enable YUV support.
YUV video conversion will be used on the computer, to improve video rendering. If this
parameter is not activated, RGB rendering will be used. Most graphics video cards
support YUV, which is more optimized than RGB.
55 Verint Video Intelligence Solutions
Nextiva S1900e Series User Guide
7. T o view video in a separate window , click Popup Video Window. The separate window
appears on top of the web interface. PTZ controls also appear.
8. To view video directly in the Live Video Streaming pane, click Embedded Video
Window. The video is embedded in the web interface pane. PTZ controls also appear.
9. To close the Live Video Streaming sub-pane, click Close Window.
Verint Video Intelligence Solutions 56
3: Using the Web Interface
PTZ controls

Manipulating the PTZ Camera

The PTZ controls that accompany live video allow you to manage the movements of the connected PTZ camera and to specify zoom values. The available commands vary depending on the PTZ protocol.
To manipulate the PTZ camera:
1. Ensure that the HTTP PTZ Controls parameter is enabled in the HTTP (W ebserver) pane;
for more information, see page 53.
2. Ensure that the serial connection between the device and camera is properly
established.
3. In the Live Video Streaming pane, select one of the two viewing methods (Embedded
Video Window in the illustration). The PTZ controls appear.
4. In the protocol list , select the PTZ protocol used by the camera. Available
protocols are: PelcoP, Kalatel, PelcoD, Infinova, and Vicon.
5. To pan (left or right) or tilt (up or down) the camera, click the desired pan/tilt controls
.
6. To zoom in, click the + button ; to zoom out, click the - button.
7. To specify the pan/tilt speed, enter a value in the Speed box . The slowest
speed is 1.
8. If the PTZ camera is automated, perform the following preset functions. A preset is a
camera angle that you can quickly select:
To save the current position of the PTZ camera, enter a number in the Preset box
, then click Store Preset .
57 Verint Video Intelligence Solutions
Nextiva S1900e Series User Guide
To use a previously stored preset, enter a number in the Preset box, then click Go
to Preset .
9. To send a copy of the image to the Windows clipboard, click capture .

Maintaining the Device

The following maintenance tasks are available on the web interface: Reboot—To restart the device, while keeping its current configuration and saving the
changes. Load—To assign the factory default settings to the device. You may keep the values of
many network parameters. The default values are listed in Appendix A on page 67. Update—To upgrade the firmware of the device. For more information about these tasks and when you should perform them, see the
“Maintaining and Troubleshooting the Device” chapter.
To reboot the device:
1. In the navigation pane, click Maintenance. The maintenance pane appears.
2. Click Reboot. A confirmation window appears.
3. Click OK.
To load the default values of the device:
1. In the navigation pane, click Maintenance. The maintenance pane appears.
Verint Video Intelligence Solutions 58
3: Using the Web Interface
2. To keep the following network parameters, ensure that Keep Network Settings is
checked:
DHCP usage Gateway Ping request target Subnet IP address DNS servers Ping request size Host name
Otherwise, you will need to reprogram the device for proper operation within the
network.
3. Click Load. A confirmation window appears.
4. Click OK. The default values are applied.
To update the firmware of the device:
Note: If you upgraded the device firmware or are accessing the firmware update process
for the first time, you need to install an ActiveX prior to proceeding (for more information, see page 22).
1. In the navigation pane, click Maintenance. The maintenance pane appears.
2. Click Update. The Firmware Update page appears.
3. In the Firmware File group box, click Browse.
4. In the Open dialog box, select the firmware file to use, then click Open.
5. Click Start.
The upgrade operation is executed.
59 Verint Video Intelligence Solutions
Nextiva S1900e Series User Guide
If the update procedure fails:
1. Restart the same procedure immediately.
2. If the problem persists, reboot the device, then restart the update procedure.
3. If the problem persists, look at the status LED for abnormal behavior.
You should tak e into consideration the following facts regarding firm ware updates using the IP network:
It can be deactivated in the command line interface (CLI) or the web interface. Ensure that the IP link is stable before starting the procedure; therefore it is not
recommended to perform it over the Internet.
Verint Video Intelligence Solutions 60
Maintaining and
Troubleshooting the
Device
You can perform maintenance and troubleshooting tasks on the S1900e. Specifically:
Updating the firmware Performing a reset Losing connection to a camera Recognizing the status LED conditions Using the command line interface (CLI)
Verint Video Intelligence Solutions 61
Nextiva S1900e Series User Guide

Updating the Firmware

You may need to update the S1900e to have access to new firmware or new features. Updating the firmware of a device retains its configuration. Many tools are available to perform the update: the SConfigurator utility, the web interface (see page 59), or a video management software like Verint Nextiva; for the detailed procedure, refer to the documentation of the software.
The latest firmware files are available on the Verint Video Intellige n ce Solutions extranet (Quick Links > Firmware and Applications > Nextiva Intelligent Edge Devices).
Note: Firmware downgrade is not supported on any device. If you perform a downgrade,
any problem encountered will not be covered by your product warranty.

Performing a Reset

Depending on the gravity of the situation, you can reboot the device, load its default configuration, or perform both these actions if the device does not react the way is should:
1. Start by rebooting the device. The device will retain all its configuration.
2. If it continues to perform abnormally, load its default configuration. All user-defined
values will be lost.
3. If the problem persists, perform a hard reset that will assign the default factory settings
to the device and reboot it.
To reboot the device:
1. Perform one of the following operations:
Press and hold the Reset button on the back of the device for one second.
In SConfigurator, go to the Units tab, select the device to reboot, click Configure,
select the Unit entry in the parameter tree, then click Reboot Unit.
In the web interface, click Maintenance in the navigation pane, then click Reboot.
The device reboots, while retaining its configuration.
To load the default configuration:
1. Perform one of the following operations:
In SConfigurator, go to the Units tab, select the device to reboot, click Configure,
select the Unit entry in the parameter tree, then click Load Default Settings.
In the web interface, click Maintenance in the navigation pane. To keep the
network configuration, check Keep Network Settings. Click Load.
This operation assigns the factory default settings to the device (listed in Appendix A on page 67). Following such a reset, you may need to reprogram the device (for instance, its IP address and VSIP port) for proper operation within its network.
Verint Video Intelligence Solutions 62
4: Maintaining and Troubleshooting the Device
To perform a hard reset:
1. Press and hold the Reset button on the device, until the system status LED flashes red
very rapidly (it can take up to 10 seconds).
2. Hold the button for an additional five seconds, until the LED turns off. The device reboots. It is ready for use with the factory default settings.

Losing Connection to a Camera

If an S1900e transmitter currently streaming video to a management software loses its connection to a camera, the corresponding display tile in the software will present an error sequence, typically a half red, half blue pattern.

Recognizing the Status LED Conditions

The system status LED is a bicolor (green-red) LED providing detailed information on the current state of the device.
Condition Description -T -R
Steady red for 5 sec. The device is powering up. Flashing red (1 sec.
intervals) Flashing green (3 sec.
intervals) Flashing green (1 sec.
intervals)
Flashing green (1 sec. intervals)
Flashing green (0.2 sec. intervals)
Flashing green (0.2 sec. intervals)
Three consecutive red blinks every 2 sec.
The IP address of the device is already assigned to another device on the network.
The firmware has started, but the device is not connected to the network.
The firmware has started, the device is connected to the network, but no video/audio/serial* data is transmitted.
The firmware has started, the device is connected to the network, but no video is received or no audio/serial* data is transmitted or received.
The firmware has started, the device is connected to the network, and video/audio/serial* data is transmitted.
The firmware has started, the device is connected to the network, and video is received or audio/serial* data is transmitted or received.
No video source is detected and no video is transmitted.
33
33
33
3
3
3
3
3
63 Verint Video Intelligence Solutions
Nextiva S1900e Series User Guide
Condition Description -T -R
Flashing green-red (1 sec. intervals)
Flashing red (0.1 sec. intervals)
One red blink A video packet is lost. In the worst case, it could
* At least one of them must be transferred to obtain the LED condition. The following power-up conditions on the system status LED are abnormal:
Condition Description
LED not lit Check the power supply and cabling. If power is available and
Steady red LED persisting more than 10 seconds
The device is undergoing a firmware update or is in backup mode.
The device is being identified.
flash at 5 Hz.
the LED stays off, call customer service for assistance. There is an internal error that prevents the device from
starting normally. Power down the device, wait 30 seconds, then power it up. If the condition persists, call customer service.
33
33

Using the Command Line Interface

3
You may need to access the command line interface (CLI) of an edge device to perform troubleshooting tasks, typically with the assistance of a Verint customer service specialist.
The available troubleshooting tasks include configuring quality of service (QoS).

Accessing the CLI

SConfigurator provides a network access to the CLI through the Telnet utility.
To enter the CLI with Telnet:
Note: Ensure that your computer and the S1900e device are in the same IP subnet.
1. Open SConfigurator.
2. Click the Units tab.
3. Click Discover.
Verint Video Intelligence Solutions 64
4: Maintaining and Troubleshooting the Device
4. Select the desired device, then click Telnet.
The CLI main menu appears in the Verint Console window.
The CLI has a timeout that is triggered after three minutes of inactivity. When the
timeout occurs:
You lose access to the command line.
The “Thank you for using the Verint CLI” message appears at the command line.
The Verint Console window becomes disabled.
The Disconnect button switches to Connect.
5. To reactivate the CLI after a timeout, click Connect.
6. To work through the CLI menu structure, follow these guidelines:
To ex ecute a command or open a menu, type in the corresponding letter or number,
then press Enter.
To return to the previous menu, enter p.
7. To end the CLI work session:
a. Save the settings by entering s at the main menu, then pressing Enter.
b. Exit the CLI by entering q at the main menu, then pressing Enter.
Depending on the changed settings, the device may perform a soft boot.
c. Close the Verint Console wind ow.
Note: Do not use the Disconnect button to exit the CLI, since it does not save your
settings.
65 Verint Video Intelligence Solutions
Nextiva S1900e Series User Guide

Configuring Quality of Service

Quality of Service (QoS) is a set of low-level networking protocols giving higher priority to more important data flows while ensuring that the less important ones do not fail. QoS is an essential technology for organizations rolling out a new generation of network applications such as real-time voice communications and high-quality video delivery.
In the Nextiva edge devices, the two available QoS flavors are Type of Service (ToS) and Differentiated Service Code Points (DSCP).
For QoS to be taken into account, the network infrastructure equipment (switches and routers) must support one of these protocols. If any of these devices does not support QoS, the QoS data will simply be processed as traditional non-QoS data. Furthermore, all Nextiva edge devices on a network must support the same QoS protocol (or no protocols at all).
You can set a priority flag to three data types coming out of an edge device: video, audio, and control. A QoS-enabled switch (or router) uses this flag to determine how the current data compares to what is currently going through it.
The QoS values are in the Advanced > Quality of Service menu.
Verint Video Intelligence Solutions 66
Factory Default
Configuration
67 Verint Video Intelligence Solutions
Nextiva S1900e Series User Guide
The S1900e series is programmed at the factory with the following configuration:
Type Configuration
Serial port Bit rate: 4800 bauds
Data bits: 8 Parity: none Stop bit: 1 RS-422/485 operating mode: RS-422 4-wire
Access management User accounts: Disabled
Telnet sessions: Enabled IP firmware update: Enabled Global security profile: Disabled SSL passkey: <empty>
Network DHCP configuration: Disabled
IP address: 169.254.*.* (based on the MAC address of the
device)
Subnet mask: 255.255.0.0 Gateway: 0.0.0.0
Video settings (North America)
Target frame rate: 30 fps Target bit rate: 4000 kbps Resolution: 4CIF (704 x 480) Maximum quantizer: 24 Video standard: NTSC Receiver mode (on the S1970e-R): Solo
Video settings (Europe) Target frame rate: 25 fps
Target bit rate: 4000 kbps Resolution: 4CIF (704 x 576) Maximum quantizer: 24 Video standard: PAL Receiver mode (on the S1970e-R): Solo
VSIP VSIP Port: 5510
VSIP Multicast IP Address: 224.16.32.1 VSIP Discovery IP Address: 255.255.255.255
Verint Video Intelligence Solutions 68
DHCP Support and
APIPA
DHCP (Dynamic Host Configuration Protocol) allows devices and computers connected to a network to automatically get a valid IP configuration from a dedicated server.
The APIPA (Automatic Private IP Addressing) scheme, available on the Windows operating systems, enables a device to assign itself a temporary IP address.
Verint Video Intelligence Solutions 69
Nextiva S1900e Series User Guide
At startup, an edge device searches for a valid IP network configuration. The device requires this configuration prior to starting its functions. The network configuration for Nextiva devices consists of:
An IP address A subnet mask A gateway
The device first looks in its local memory. If no configuration is found, it tries to contact a DHCP server. If DHCP configuration fails—if the device does not find a server or if it cannot get a configuration from it within one minute—the device assigns itself temporary network parameters based on the APIPA addressing scheme. This scheme allows a device to find a unique IP address until it receives a complete network configuration, either manually or from a DHCP server.
A device in APIPA mode does not reside on the same subnet as the other devices on the IP network; therefore, it may not be able to see or be visible by the other devices. Devices use the following temporary APIPA configuration:
IP address: 169.254.X.Y (where X and Y are based on the last two digits of the MAC
address of the device)
Subnet mask: 255.255.0.0 Gateway: 169.254. *. *
A device is in APIPA mode:
The first time it boots up After receiving a duplicate IP address After a hardware reset When the DHCP server does not have any available IP addresses After loading the default parameters
DHCP configuration is automatically disabled after a factory reset.
Verint Video Intelligence Solutions 70

Audio Pinouts

Verint Video Intelligence Solutions 71
Nextiva S1900e Series User Guide
Mic/line-in
Mic bias (not connected for line-in)
Ground (shield)
Mic bias (not connected for line-in)
Mic/Line-in
Speaker
Ground (shield)
Speaker
Here is the pinout of the 1/8-inch (3.5 mm) stereo jacks for audio input:
For audio output, the jacks are configured the following way:
Verint Video Intelligence Solutions 72

Technical Specifications

Verint Video Intelligence Solutions 73
Nextiva S1900e Series User Guide
Here are the S1900e series technical specifications:
Video Compression MPEG-4-based, MPEG-4 ISO 1449 6-2 compliant,
and MJPEG
Frame rate Up to 30 frames or 60 fields per second in NTSC
(25 frames or 50 fields in PAL), programmable (full
motion) Input 1 composite, 1 Vpp into 75 ohms Output 1 composite, 1 Vpp into 75 ohms Resolution Scalable from 176 x 128 to 704 x 480 NTSC pixels
(176 x 144 to 704 x 576 PAL pixels) Standard NTSC or PAL Connectors BNC female Bandwidth Configurable between 9 and 6000 kbps
Serial Port Electrical levels RS-422/485 2/4 wires (230 kbps max.)
Connectors Pluggable screw-terminal strip Operating mode Transparent serial port supporting any
asynchronous serial protocol
Alarm and audio Alarm input 1 dry contact
Alarm output 1 relay contact (48V AC/DC at 100 mA max.) Bidirectional audio Input: -20 to -3 dBV into 30 kohm
Output: -45 to -3 dBV into 16 ohms min. Audio connectors One set of 1/8 inch (3.5 mm) input and output
stereo jacks Audio resolution 16 bits per sample Audio sampling rate 8 kHz
Network Interface Ethernet 10/100Base-T
Connector RJ-45 jack Protocols Transport: RTP/IP, UDP/IP, TCP/IP, multicast IP
Others: DNS and DHCP client Security SSL-based authentication
Verint Video Intelligence Solutions 74
D: Technical Specifications
Power PoE PoE IEEE 802.3af class 3 device
12V DC S1900e-AS: 6.0W max. (500 mA at 12V DC)
S1950e: 3.7W max. (310 mA at 12V DC)
S1970e: 4.3W max. (360 mA at 12V DC)
Physical Enclosure Aluminum extrusion with plastic end plates
Size non-XT models: 4.2D x 3.5W x 1.7H inches (107D
x 89W x 43H millimeters)
XT models: 7.8D x 3.5W x 1.7H (198D x 89W x
43H millimeters) Weight non-XT models: 9.2 oz (261 g)
XT models: 12.6 oz (358 g) Environment non-XT models: 32°F to 122°F (0°C to 50°C)
XT models: -22°F to 140°F (-30°C to 60°C) Humidity 95% non condensing at 122°F (50°C)
Management Configuration Remote using Nextiva, nDVR, SConfigurator,
Internet Explorer, or Telnet
Certification/
USA FCC part 15 (subpart B, class A)
Regulation
Canada ICES-003/NMB-003 Europe CE marked, EN 55022:1998 Class A, EN 55024
Directive 2002/95/EC of the European Parliament
and of the Council of 27 January 2003 (RoHS)
75 Verint Video Intelligence Solutions

Glossary

This glossary is common to the Nextiva line of edge device products.
Verint Video Intelligence Solutions 76
Glossary
Access Point A communication hub for connecting wireless edge devices to a wired LAN. AES (Advanced Encryption Standard) An encryption standard used in the WPA2
authentication method. APIPA (Automatic Private IP Addressing) A feature of Windows-based operating systems
that enables a device to automatically assign itself an IP address when there is no Dynamic Host Configuration Protocol (DHCP) server available to perform that function. Also known as AutoIP.
Bridge See Wireless Bridge. CCTV (Closed Circuit Television) A television system in which signals are not publicly
distributed; cameras are connected to television monitors in a limited area such as a store, an office building, or on a college campus. CCTV is commonly used in surveillance systems.
CIF (Common Intermediate Format) A video format that easily supports both NTSC and PAL signals. Many CIF flavors are available, including CIF, QCIF, 2CIF, and 4CIF. Each flavor corresponds to a specific number of lines and columns per video frame.
CLI (Command Line Interface) A textual user interface in which the user responds to a prompt by typing a command.
Codec (Coder/Decoder) A software library that compresses or decompresses a video stream following a specific protocol.
Configuration Assistant A proprietary graphical program used to configure and update the firmware of the S1100 edge devices.
Decoder See Receiver. DHCP (Dynamic Host Configuration Protocol) A communication protocol that lets network
administrators manage centrally and automate the assignment of Internet Protocol (IP) addresses in a network.
DVR (Digital Video Recorder) A device (usually a computer) that acts like a VCR in that it has the ability to record and play back video images. The DVR takes the feed from a camera and records it into a digital format on a storage device which is most commonly the hard drive.
Edge Device A Nextiva device transmitting or receiving video signals through an IP network. The devices can be wireless or wired; some transmitters are IP cameras.
Encoder See Transmitter. Ethernet A local area network (LAN) architecture using a bus or star topology and
supporting data transfer rates of 10, 100, and 1000 Mbps. It is one of the most widely implemented LAN standards. The 802.11 protocols are often referred to as “wireless Ethernet.”
Firmware Software stored in read-only memory (ROM) or programmable ROM (PROM), therefore becoming a permanent part of a computing device.
IP (Internet Protocol) The network layer for the TCP/IP protocol suite widely used on Ethernet networks.
LAN (Local Area Network) A computer network that spans a relatively small area. A LAN can connect workstations, personal computers, and surveillance equipment (like edge devices). See also WAN.
77 Verint Video Intelligence Solutions
Nextiva S1900e Series User Guide
MPEG-4 A graphics and video lossy compression algorithm standard that is derived from MPEG-1, MPEG-2, and H.263. MPEG-4 extends these earlier algorithms with synthesis of speech and video, fractal compression, computer visualization, and artificial intelligence-based image processing techniques.
Multicast Communication between a sender and multiple receivers on a network; the devices can be located across multiple subnets, but not through the Internet. Multicast is a set of protocols using UDP/IP for transport.
NTSC (National Television Standards Committee) The North American standard (525-line interlaced raster-scanned video) for the generation, transmission, and reception of television signals. In addition to North America, the NTSC standard is used in Central America, a number of South American countries, and some Asian countries, including Japan. Compare with PAL.
NTP (Network Time Protocol) A protocol designed to synchronize the clocks of devices over a network.
OSD (On-screen Display) Status information displayed on the video monitor connected to a receiver edge device.
PAL (Phase Alternation by Line) A television signal standard (625 lines) used in the United Kingdom, much of western Europe, several South American countries, some Middle East and Asian countries, several African countries, Australia, New Zealand, and other Pacific island countries. Compare with NTSC.
PEAP (Protected Extensible Authentication Protocol) A method to securely transmit authentication information, including passwords, over a wireless network.
Point-to-Point Connection The association of a transmitter and a receiver to view video coming from an analog camera on an analog monitor.
PSK (Pre-Shared Key) A mode of the WPA and WPA2 security protocols, designed for home and small office networks that cannot afford the cost and complexity of an authentication server. It is also known as personal mode.
PTL (Push-To-Listen) In a two-way system, the communication mode in which the listener must push a button while listening.
PTT (push-To-Talk) In a two-way system, the communication mode in which the talker must push a button while talking.
PTZ Camera (Pan-Tilt-Zoom) An electronic camera that can be rotated left, right, up, or down as well as zoomed in to get a magnified view of an object or area. A PTZ camera monitors a larger area than a fixed camera.
QoS (Quality of Service) A set of low-level networking protocols giving higher priority to more important data flows while ensuring that the less important ones do not fail.
Receiver A device converting a digital video signal into an analog form. Also called decoder.
Repeater A range extender for wireless links. RF (Radio Frequency) Any frequency within the electromagnetic spectrum associated with
radio wave propagation. When a modulated signal is supplied to an antenna, an electromagnetic field is created that is able to propagate through space. Many wireless technologies are based on RF field propagation.
Verint Video Intelligence Solutions 78
Glossary
RS-232 A standard interface approved by the Electronic Industries Alliance (EIA) for connecting serial devices.
RS-422 A standard interface approved by the Electronic Industries Alliance (EIA) for connecting serial devices, designed to replace the older RS-232 standard because it supports higher data rates and greater immunity to electrical interference.
RS-485 An Electronics Industry Alliance (EIA) standard for multipoint communications. SConfigurator A proprietary graphical program used to configure and update the firmware
of edge devices. Serial Port An interface that can be used for serial communication, in which only one bit is
transmitted at a time. A serial port is a general-purpose interface that can be used for almost any type of device.
SSL (Secure Sockets Layer) A commonly used protocol for transmitting private documents via the Internet. SSL works by using a public key to encrypt data that is transferred over the SSL connection. The SSL protocol secures the following data: I/O, serial port, and VSIP communication; it does not apply to audio and video transmission.
TKIP (Temporal Key Integrity Protocol) A security protocol used in the WPA authentication method.
TLS (Transport Layer Security) A cryptographic protocol that provide secure communications on a wireless network.
Transceiver (Transmitter/Receiver) A device that both transmits and receives analog or digital signals.
Transmitter A device sending video signals captured with a connected camera to a receiver. The transmitter converts the analog signal into a digital form before transmitting it. Also called encoder.
TTLS (Tunneled Transport Layer Security) A cryptographic protocol that creates a secure TLS tunnel.
VSIP (Video Services over IP) A proprietary communication protocol for sending messages between a computer and a Nextiva edge device, or between two devices.
WAN (Wide Area Network) A computer network that spans a relatively large geographical area. Typically, a WAN consists of two or more local area networks (LANs).
WEP (Wired Equivalent Privacy) A security protocol for wireless local area networks (WLANs) defined in the 802.11b standard. It is designed to afford wireless networks the same level of protection as a comparable wired network.
Wireless Bridge A link between two networks, wired or wireless. Wireless Cell A group of wireless devices that communicate together on the same radio
frequency channel and share the same wireless passkey. Wireless Transmission A technology in which electronic devices send information to
receivers using radio waves rather than wiring. WPA (Wi-Fi Protected Access version 1) An authentication method to secure wireless
systems. It is the successor of WEP. WPA implements the majority of the IEEE 802.11i standard.
79 Verint Video Intelligence Solutions
Nextiva S1900e Series User Guide
WPA2 (Wi-Fi Protected Access version 2) An authentication method that implements the full 802.11i standard, but will not work with some older network cards. It is also known as
802.11i.
Verint Video Intelligence Solutions 80

Index

Numerics
1/8-inch plug 72
3.5 mm plug 18
A
abnormal power-up conditions 64 access management 27 account, user 27 ActiveX controls for the web interface 22 address, IP. See IP address. administrator account 27 alarm configuration 17 analog monitor 48 analytics, video 3 APIPA addressing scheme 69 audio
input/output 18 pinout of jacks 72 settings 45 specifications 20
51
20
B
bidirectional audio 18 bit rate
serial port 26 video 35
C
cable. See Ethernet cable. camera
data port configuration 2
losing a connection 63 casing of the device 7 certificate, SSL 3 characteristics of the device 2 CLI (command line interface) 30 compliance 84 computer requirements 13 configuration
alarm 18
audio 18
camera data port 2
default 58
device, initial 13
I/O 18
web interface 26
20
, 62, 67
15
20
53
, 64
connection
audio 18 to a camera, losing 63 Ethernet cable 10 PoE 9 point-to-point 15 power 9 RS-422/485 11
crossover Ethernet cable 10
, 19, 72
, 11
D
default configuration 58, 62, 67 DHCP (Dynamic Host Configuration Protocol) 15
32 display on analog monitor 48 downgrade of firmware 62 DSCP (Differentiated Service Code Points) 66 duplex audio 18 duplicate IP address 13
51
E
EIA-422. See RS-422/485. enclosure of the device 7 encoder use 3 equipment list 6 Ethernet cable
maximum length 10 RJ-45 connector 7 usage 10
event configuration 17
, 11
F
factory default configuration 58, 62, 67 features of the device 2 firmware update
ActiveX control for 22 downgrading 62 performing 58
preventing 30 frame rate 3 full duplex audio 18
, 62
, 35, 37
G
gateway 32 global security profile 30 GMT (Greenwich Mean Time) 4 7
,
Verint Video Intelligence Solutions 81
Nextiva S1900e Series User Guide
H
hardware reset 62 HTTP access 30 HTTP settings for the web interface 52 HTTPS access 30
I
I/O, alarm or audio 1720 injector, PoE 9 installation 9 IntelliView 3 IP address
APIPA 69 duplicate 13 setting 13 temporary 69
, 15, 32
L
LED, status 63 length of Ethernet cable 10 live video
accessing 53
ActiveX control for 22 loading default configuration 58 local settings for live viewin g 53 losing connection to a camera 63
58
, 62, 67
M
maintenance 58, 6166 mask, subnet 32 maximum length of Ethernet cable 10 microphone, multimedia 19 monitor, analog 48 multimedia microphone 19
51
pinout
audio 72
serial port 11 PoE (power-over-Ethernet) 9 point-to-point connection 15 port, serial. See serial port. power connection 9 power requirements 2 power-over-Ethernet (PoE) 9 power-up conditions 64 preventing access 30 protection of device configuration 29 protocols supported
PTZ 57
serial 11 PTT (push-to-talk) 18 PTZ (pan-tilt-zoom) 53
, 57
Q
quadrant, OSD 48 Quality of Service (QoS) 66
R
rate control 36, 38 rebooting the device 58 receiver device 15 receiver display 48 red/blue display 63 requirements
computer 13
power 2 Reset button 63 reset to factory default 58 resolution, video 4 RoHS 87 RS-422/485 11
, 27
, 62
51
, 62, 67
, 36, 38
N
name of device 44 network
settings 15 noise reduction filter 36 NTP (Network Time Protocol) 47
, 32
, 38
O
on-screen display (OSD) 4851 options, when ordering a device 6 output, alarm or audio 17
20
P
panel of device 7 pan-tilt-zoom (PTZ) 53 passkey 27
Verint Video Intelligence Solutions 82
, 30
, 57
S
SConfigurator
configuring the device 13
creating a connection 16 secure HTTP access 30 serial port 11 serial protocols supported 11 shipment list 6 specifications
audio 20
technical 73 SSL (Secure Sockets Layer) 3 status
device 31
video 43 status LED 63 straight-through Ethernet cable 10 subnet mask 32
, 26
, 30
, 11
Index
system status 31 system time 47
T
technical specifications 73 Telnet
accessing the CLI 64
preventing access 29 temporary IP address 69 time, system 47 ToS (Type of Service) 66 troubleshooting 61
66
U
user account 27
V
Verint web site vi video analytics 3 video settings 3 video, live 53 VSIP port 44 VSIP settings 44
, 3343
58
W
web client account 27 web interface
accessing with a password 27
ActiveX controls for 22
after a firmware update 22
for configuration 26
HTTP settings 52
live video 53
maintaining the device with 58
opening 24
preventing access 30
secure access 30 web site, Verint vi
53
58
83 Verint Video Intelligence Solutions

Compliance

Verint Video Intelligence Solutions 84
Compliance

United States Statement for FCC

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

Industry Canada Statement

This Class A digital apparatus complies with Canadian ICES-003. Cet appareil numérique de la classe A est conforme à la norme NMB-003 du Canada.
85 Verint Video Intelligence Solutions
Nextiva S1900e Series User Guide

Europe EN 55022 Statement

Thi s is to ce rti fy th at the Ne xt iv a M od els S1900e-AS, S1900e-AS- XT, S1950e, S1950e- XT, S1970e, S1970e-XT, S1970e-R, and S1970e-R-XT Ethernet video servers are shielded against the generation of radio interference in accordance with the application of Council Directive 89/336/ECC, Article 4a. Conformity is declared by the application of EN55022 Class A (CISPR 22).
Declaration of Conformity
Manufacturer:
Verint Systems Inc. 1800 Berlier Laval, Québec H7L 4S4 Canada
Declares under sole responsibility that the product:
Product name: Ethernet video server Model numbers: S1900e-AS, S1900e-AS-XT, S1950e, S1950e-XT, S1970e, S1970e-XT, S1970e-R, and S1970e-R-XT
To which this declaration relates is in conformity with the following standards or other documents:
EMC Directive 89/336/EEC:
EN55022: 1998 class A EN55024: 1998
EN 61000-4-3: 1996 3 V/m EN 61000-4-6: 1996 3 Vrms EN 61000-4-2: 1995 4 kV CD, 8 kV AD EN 61000-4-4: 1995 1kV (power), 500V (signal) EN 61000-4-11: 1994 EN 61000-4-5: 1995 2kV L-E, 1kV L-L ENV50204: 1995
Verint hereby declares that the equipment specified above conforms to the above Directive(s) and Standard(s).
Laval, Canada For the official signed declaration of conformity, visit http://www.verint.com/certifications
Verint Video Intelligence Solutions 86
.
Compliance

RoHS Declaration of Compliance

Verint believes in the importance of conducting our business in a manner that will help protect the environment as well as our employees, customers, and the public.
To that end, we are committed to bringing our existing and future product lines into EU RoHS Directive compliance.
Thus, the following products, S1900e-AS, S1900e-AS-XT, S1950e, S1950e-XT, S1970e, S1970e-XT, S1970e-R, and S1970e-R -XT, are complia nt with the DIR ECTIVE 2002/95/EC OF THE EUROPEAN PARLIAMENT AND OF THE COUNCIL of 27 January 2003 (RoHS) regarding the restriction of the use of certain hazardous substances in electrical and electronic equipment.
The S1900e-AS, S1900e-AS-XT, S1950e, S1950e-XT, S1970e, S1970e-XT, S1970e-R, and S1970e-R-XT p ro du cts wi ll n ot ex ce ed t he max im um con ce nt ra ti ons of 0.1 % b y w eig ht in homogenous materials for lead, hex chrome, mercury, PBB, PBDE, and 0.01% for cadmium. In addition, the S1900e-AS, S1900e-AS-XT, S1950e, S1950e-XT, S1970e, S1970e-XT, S1970e-R, and S1970e-R-XT products will qualify for the “lead in servers solders” exemption as set forth in the Directive.
This declaration is provided based on reasonable inquiry of our suppliers and represents our actual knowledge based on the information provided by our suppliers.
87 Verint Video Intelligence Solutions
AMERICAS EMEA APAC
info@verint.com marketing.emea@verint.com marketing.apac@verint.com www.verint.com/videosolutions www.verint.com/videosolutions www.verint.com/videosolutions
Loading...