Verilink PRISM 3010 Installation Guide

Download

3010 V

Configuration Guide

OICE

ODULES

45-00136

7.0

The PRISM 3010 six-port voice card is the solution for integrating analog voice applications into fractional or full T1 services. Hardware switch settings are not required on PRISM modules, except for the jumpers on the the FXO card.

Module configuration is performed using the PRISM front panel LCD interface, a terminal connected to the SUPV port, the 8100A Site Controller.

If the PRISM is equipped with the SNMP/Telnet interface, the voice card can be accessed via a Telnet session from any LAN connected device.

Card Installation

Note: Only two FXO or FXS cards can be used in the standard 3060 chassis (p/n F-3060-001--xxxx). Four FXS or FXO cards can be used in the 3060 chassis with the enhanced power supply (p/n F-3060-001A-xxxx).

Option modules may be damaged by static electricity. Use ESD (electrostatic device) precautionary measures such as wearing static grounding straps and storing modules in the supplied antistatic bags.

Warning: To pr e vent electric shock or damage to the unit, turn the r ear panel power switch OFF before removing or installing any option modules.

To add a module to an empty slot, remove the cover plate which is held in place by two screws. Carefully slide the new card along the guides with the component side facing down. Push the board in until the faceplate rests against the rear panel. Replace the screws.

If resistance is encountered when inserting the card, remove the card and verify t hat there are no obstructions in its path. Also check fo r bent or damaged pins in the connectors of the module and chassi s .

2-Wire FXS Connection

Pair Pin # Color Function

1 26 T

2 27 T

3 28 T

4 29 T

5 30 T

6 31 T

1 R

2 R

3 R

4 R

5 R

6 R

White / Blue Blue / White

White / Orange Orange / White

White / Green Green / White

White / Brown Brown / White

White / Slate Slate / White

Red / Blue Blue / Red

Circuit #1

Circuit #2

Circuit #3

Circuit #4

Circuit #5

Circuit #6

Specifications

Connector: AMP 50-pin (25 pairs), female Encoding: PCM six ports per card Noise: < 20 dBrnc Signal to Noise: > 35 dB Freq. Response: 300 Hz to 3 kHz (± 0.5 dB) Power: Internal (FXS and FXO)

External (4-Wire E&M: -48 VDC)

Signalling: See the Signalling section on the

other side. Warranty: 5 Years Operating Temp: 0° to 50°C (32° to 122°F) Storage Temp: -20° to 85°C (-4° to 185°F) Humidity: 95% max (non-condensing)

FXO Line Build Out Jumpers

The line build out choices are AT&T Compromise and 900 Ω. Set the jumper pairs the same way for each channel. Using the diagram below as a refere nc e, AT&T Compromise has the jumper set on the center and right pins. 900 Ω has the jumper set on the center and left pins. The default settin g is AT&T Compromise.

STRAP

Channel 6 Channel 5 Channel 4 Channel 3

Channel 2

Channel 1

J18, J19 J16, J17 J14, J15

J12, J13 J10, J11

J8, J9

Voice Card Connections

The 3010 voi ce card s are used to inter face up to s ix piec es of analog telephone equipment (telephones or key equipment) to a T1 facility.

The 4-Wire E&M requires an external -48 VDC source (42 to 60 VDC at 300 mA). The external source is used for relay activation and Type 2 signalling.

Connection to each type of voice card is made through a rear panel 25-pair female connector, retained by a hookand-loop-fastener strap. Refer to the tables on this page for connection information.

2-Wire FXO Connection

Pair Pin # Color Function

1 26 T

2 27 T

3 28 T

4 29 T

5 30 T

6 31 T

25 50 T

1 R

2 R

3 R

4 R

5 R

6 R

25 R

White / Blue Blue / White

White / Orange Orange / White

White / Green Green / White

White / Brown Brown / White

White / Slate Slate / White

Red / Blue Blue / Red

Violet / Slate Slate / V io let

Circuit #1

Circuit #2

Circuit #3

Circuit #4

Circuit #5

Circuit #6

-4 8 VDC VDC Return

3010 Module Options

Voice Card Type Part Number

6-Port FXS F-3010-200A-111 6-Port E&M F-3010-200--112 (Types I, II, III) 6-Port FXO F-3010-200A-113 6-Port E&M F-3010-200--114 (Types I, II, III, IV, V)

4-Wire E&M Connection

Pair Pin # Color Function Circuit

1 26 T

Pair Pin # Color Function Circuit

1 26 T

2 27 T

3 28 T

4 29 T

5 30 T

6 31 T

7 32 T

8 33 T

9 34 T

10 35 T

11 36 T

12 37 T

13 38 T

14 39 T

15 40 T

16 41 T

17 42 T

18 43 T

19 44 T

20 45 T

21 46 T

22 47 T

23 48 T

24 49 T

25 50 T

* Option of connecting power to the voice card using

cable pair(s) or the external lugs.

1 R

2 R

3 R

4 R

5 R

6 R

7 R

8 R

9 R

10 R

11 R

12 R

13 R

14 R

15 R

16 R

17 R

18 R

19 R

20 R

21 R

22 R

23 R

24 R

25 R

White / Blue Blue / White

White / Blue

White / Orange

Blue / White

Orange / White

White / Orange

White / Green

Orange / White

Green / White

White / Green

White / Brown

Green / White

Brown / Whit e

White / Brown

White / Slate

Brown / White

Slate / White

White / Slate

Red / Blue

Slate / White

Blue / Red

Red / Blue

Red / Orange

Blue / Red

Orange / Red

Red / Orange

Red / Green

Orange / Red

Green / Red

Red / Green

Red / Brown

Green / Red

Brown / Red

Red / Brown

Red / Slate

Brown / Red

Slate / Red

Red / Slate

Black / Blue

Slate / Red

Blue / Black

Black / Blue

Black / Orange

Blue / Black

Orange / Bl ack

Black / Orange

Black / Green

Orange / Black

Green / Black

Black / Green

Black / Brow n

Green / Black

Brown / Black

Black / Brown

Black / Slate

Brown / Black

Slate / Black

Black / Slate

Yellow / Blue

Slate / Black

Blue / Yellow

Yellow / Blue

Yellow / Orange

Blue / Yellow

Orange / Yellow

Yellow / O rang e

Yellow / Green

Orange / Yellow

Green / Yellow

Yellow / Green

Yellow / Brown

Green / Yellow

Brown / Yellow

Yellow / Brown

Yellow / Slate

Brown / Yellow

Slate / Yellow

Yellow / Slate

Violet / Blue

Slate / Yellow

Blue / Violet

Violet / Blue

Violet / Orange

Blue / Violet

Orange / Violet

Violet / Orange

Violet / Green

Orange / Violet

Green / Violet

Violet / Gree n

Vi olet / Brown

Green / Violet

Brown / Violet

Violet / Brown

Violet / Slate

Brown / Violet

Slate / Violet

Violet / Slate Slate / Violet

Audio In Tip Audio In Ring

Audio In

Audio Out Tip

Audio Out Ring

Audio Out

E Lead

Signal Ground

E Lead

M Lead

Signal Ground

Signal Battery

M Lead

Audio In Tip

Signal Battery

Audio In Ring

Audio In

Audio Out Tip

Audio Out Ring

Audio Out

E Lead

Signal Ground

E Lead

M Lead

Signal Gr ound

Signal Battery

M Lead

Audio In Tip

Signal Battery

Audio In Ring

Audio In

Audio Out Tip

Audio Out Ring

Audio Out

E Lead

Signal Ground

E Lead

M Lead

Signal Ground

Signal Battery

M Lead

Audio In Tip

Signal Battery

Audio In Ring

Audio In

Audio Out Tip

Audio Out Ring

Audio Out

E Lead

Signal Ground

E Lead

M Lead

Signal Ground

Signal Battery

M Lead

Audio In Tip

Signal Battery

Audio In Ring

Audio In

Audio Out Tip

Audio Out Ring

Audio Out

E Lead

Signal Ground

E Lead

M Lead

Signal Ground

Signal Battery

M Lead

Audio In Tip

Signal Battery

Audio In Ring

Audio In

Audio Out Tip

Audio Out Ring

Audio

E Lead

Out Rx

Signal Ground

E Lead

M Lead

Signal Gr ound

Signal Battery

M Lead

Signalling

Signal Battery

Power

Signalling Power

Circuit #1

Circuit #2

Circuit #3

Circuit #4

Circuit #5

Circuit #6

-48VDC* VDC RTN

-48 VDC VDC RTN

Port Configuration Menu

The Voice Card Configuration screen display allows the assignment of voice DS0s to network channels. This display is accessible from the PRISM unit front panel LCD, its terminal interface, or the 8100A Site Controller under the Configuration top level menu. Only the voice ports with the Mode parameter set to ACTIVE are connected to the selected network channel.

The 3010 voice modules have six voice circuits, each of which is independently assignable to a selected net work channel. For a more detailed description of voice port operation, refer to the reference manual for the product where the card is located. The following fields are available for voice port configuration:

Port: This field indicates the port number of the card in the assigned slot. DS0: This field assigns the voice port to a network channel. The choices are

channels 1 through 24. Mode: This field selects whether the voice port is actively assigned to a network

channel, ACTIVE, or is not used, SPARE. If set to SPARE, the other voice port parameters are ignored and the port is inactive.

State: This field displays the voice por t st a tus a s eith er in t he BUSY or IDLE s tate. Name: This field may be used to provide up to 20 characters of text for identify-

ing the voice circuit name and number. Signalling: This field selects the supervisory operation of the voice port. The

choices for the different modules are as follows. FXS

• FXS/LS Foreign Exchange Station / Loop Start

• FXS/GS Foreign Exchange Station / Ground Start

• MEG/LS MEGACOM

• MEG/GS MEGACOM / Ground Start

• PLAR Private Line Automatic Ringdown

• DID/DNIS Direct Inward Dialing/Dialed Number Identification Service [Dial Pulse Originate (DPO) mode]

• DNISW/LS Loop Start DNIS (LS-DNIS) with wink

• DNISD/LS LS-DNIS with delay start

• DNISWR/LS LS-DNIS with wink and Reverse Battery

• DNISDR/LS LS-DNIS with delay and Reverse Battery

• DNISW/GS Ground Start DNIS (GS-DNIS) with wink

• DNISD/GS GS-DNIS with delay start

• DNISWR/GS GS-DNIS with wink and Reverse Battery

• DNISDR/GS GS-DNIS with delay and Reverse Battery

FXO

• FXO/LS Foreign Exchange Station / Loop Start

• FXO/GS Foreign Exchange Station / Ground Start

• FXO UVG Foreign Exchange Office/Universal Voice Grade

• FXO UVGR Foreign Exchange Office /Universal Voice Grade with Reverse Battery

• DID/DNIS Direct Inward Dialing/Dialed Number Identifi ca ti on Service [Dial Pulse Terminate (DPT) mode]

4-Wire E&M F-3010-200--112

• T ype I Signalling YES YES

• T ype II Signalling YES YES

• T ype III Signalling YES YES

• T ype IV and V Signalling NO YES

• TO Transmission Only YES YES

Delay Sec ond s : If the signalling mode has a delay, it can be set from 1 to 5 seconds. Tx Gain: This field selects the transmit gain over the following ran ge s:

2-Wire FXS: -4.0 dB fixed 2-Wire FXO: -6 dB to 0 dB 4-Wire E&M: -10 dB to +3 dB, 0 dB

Rx Gain: This field selects the receive gain over the following ranges: 2-Wire FXS: -11 dB to 0 dB

2-Wire FXO: -6 dB 4-Wire E&M: -16 dB to +2 dB, 0 dB

Slot/Channel Allocation: These display-only fields indicate the network channel assignments with Channel 1 on the left and Channel 24 on the right. The upper line indicates the card slot to which the channel is allocated. The lower line indi cates the port in the assigned card for that channel.

to 0 dB

/ Loop Start

F-3010-200--114

2-Wire FXS Screen

3060 DSU Time: HH:MM:SS Element Rev xx.xx/x.xx Date: MM/DD/YY

--------------------- VOICE CARD CONFIGURATION -------------------

Slot: (2) Card Type: 2 Wire FXS

Delay Tx Gn Rx Gn Port DS0 Mode State Name/ID Sig. Secs. dB dB

-----------------------------------------------------------------A ( 1) [ACTIVE] BUSY ( ) [FXS/LS] (-4.0) ( -2) B ( 2) [ACTIVE] IDLE ( ) [FXS/GS] (-4.0) ( -2) C ( 3) [ACTIVE] BUSY ( ) [MEG/LS] (-4.0) ( -2) D ( 4) [SPARE ] IDLE ( ) [MEG/GS] (-4.0) ( -2) E ( 5) [SPARE ] IDLE ( ) [PLAR ] (-4.0) ( -2) F ( 6) [ACTIVE] BUSY ( ) [FXS/LS] (-4.0) ( -2)

222222 333333 ------ ----- Channel Allocation: ABCDEF AAAAAA ------ ------

---------------------------- Messages ----------------------------

2-Wire FXO Screen

3060 DSU Time: HH:MM:SS Element Rev xx.xx/x.xx Date: MM/DD/YY

--------------------- VOICE CARD CONFIGURATION -------------------

Slot: (2) Card Type: 2 Wire FXO

Delay Tx Gn Rx Gn Port DS0 Mode State Name/ID Sig. Secs. dB dB

-----------------------------------------------------------------A ( 1) [ACTIVE] BUSY ( ) [FXS/LS] ( -6) ( -2) B ( 2) [ACTIVE] IDLE ( ) [FXS/GS] ( -6) ( -2) C ( 3) [ACTIVE] BUSY ( ) [MEG/LS] ( -6) ( -2) D ( 4) [SPARE ] IDLE ( ) [MEG/GS] ( -6) ( -2) E ( 5) [SPARE ] IDLE ( ) [FXO/GS] ( -6) ( -2) F ( 6) [ACTIVE] BUSY ( ) [FXO/LS] ( -6) ( -2)

222222 333333 ------ ----- Channel Allocation: ABCDEF AAAAAA ------ ------

---------------------------- Messages ----------------------------

4-Wire E&M Screen

3060 DSU Time: HH:MM:SS Element Rev xx.xx/x.xx Date: MM/DD/YY

--------------------- VOICE CARD CONFIGURATION -------------------

Slot: (2) Card Type: 4 Wire E&M

Delay Tx Gn Rx Gn Port DS0 Mode State Name/ID Sig. Secs. dB dB

-----------------------------------------------------------------A ( 1) [ACTIVE] BUSY ( ) [TYPE 1] (-.5) ( +2) B ( 2) [ACTIVE] IDLE ( ) [TYPE 3] (-.5) ( +2) C ( 3) [ACTIVE] BUSY ( ) [TYPE 2] (-.5) ( +2) D ( 4) [SPARE ] IDLE ( ) [TO ] (-.5) ( +2) E ( 5) [SPARE ] IDLE ( ) [TYPE 1] (-.5) ( +2) F ( 6) [ACTIVE] BUSY ( ) [TYPE 1] (-.5) ( +2)

222222 333333 ------ ----- Channel Allocation: ABCDEF AAAAAA ------ ------

---------------------------- Messages ----------------------------

127 Jetplex Circle

Madison, Alabama 35758

www.verilink.com

Sales and Marketing

800-285-2755 256-772-3770 info@verilink.com

MEGACOM is a registered trademark of AT&T.

Technical Support 800-285-2755

256-772-3770 support@verilink.com

Returns/RMA

800-285-2755, ext. 2282

Verilink PRISM 3010 Installation Guide

Specifications and Main Features

Frequently Asked Questions

User Manual