Craft
Setting up
Using the Craft Interface
This part of the Management Section describ es how to use th e Craft
interface to manage AS2000 and AS3000 nodes. With the Craft
interface, you can ac cess AS2000 and AS3000 contr oller modules
from a PC or terminal using a direct or Telnet connection.
This document describes:
Setting up
•
• The Main Menu
• Sample submenus
The connection between an ASCII terminal and AS2000 modules
may be direct or through Te lnet. If you plan to use Teln et, you still
must first use a direct connectio n to set up network parameters.
Direct Connection
The Craft interf ace can be accessed thr ough a direct conne ction to
the node controller (SCM, NCM, SCC, NCC) or shelf controller. From
an ASCII terminal or PC with terminal emulator pro g ram, proceed
as follows:
1. Connect the ASCII terminal to the port labeled C
on the front panel of the module. Use the Craft cable (P/N
458-501788-008) described in the “System Cables” appendix
of the
2. Go to the terminal settings screen of your terminal or terminal
emulator. If you are using Windows 95 Hyper Terminal, use
the File>New Connection pull-down menu to access the
parameters. If you are using the Wi ndow 3.1’s Terminal
program, choose the Communications option from the
Settings pull-down menu to access the parameters.
3. Set your terminal parameters to the following values:
AS2000: The Basics
• 19.2 kbit/s baud rate
• 8 data bits
•no parity
•one stop-bit
• no flow-control
user manual.
RAFT
or L
OCAL
• X-ON, X-OFF disabled
Verilink Craft Interface Craft-1
Using the Craft Inter face
Using Telnet
Telnet access is available for the SCM, NCM and SCC controller
modules. Prior to accessing the Craft interface using Telnet you
must configure the Ethernet IP address and related network
parameters for the SCM, NCM o r SCC you wish to connect to.
Therefore, the Craft interface must be accessed directly (t hrough
the front panel) at least once to before Telnet can be used (see
previous section). You cannot use Telnet to access an NCC.
In a shell, terminal, browser, or Telnet application window, use a
command similar to the following (substitute the IP address of the
desired controller):
C:\> telnet 192.94.46.54
A message indicates you have connected to the controller:
Figure 1 Telnet Session Connecting to the NCM Node
Trying 192.94.46.54 ...
Connected to 192.94.46.54.
Escape character is '^]'.
pSOSystem (192.94.46.54)
Copyright (c) Integrated Systems, Inc., 1992.
Welcome to pSOSystem...
pSH+>
Exiting From
Logging On
Telnet
Exit from the P-shell and close the Telnet connection by typing
“exit” or pressing C
TRL
-D at the pSH+> prompt.
Once the module has booted up, you will see some initialization
notices.
If there is a prompt pSH+>, type in “craft”.
The password prompt is: Your Password? If you are accessing the
node for the first ti m e , pr e s s E
Until you change it, the E
NOTE: Some newer products use “verilink” as the default password. See
the user manual for the module you are using.
NTER
at the password prompt.
NTER
key is the default password.
If you have changed the password, type the correct password (up to
eight characters, including spaces). The screen will display
placeholders (******) as you type the password. Press E
NTER
.
The Craft interface Main Menu displays.
Timeout
The Craft interface will time out after 15 minutes of inactivity and
automaticall y re tu rn to th e pSH +> prompt.
Craft-2 Verilink Craft Interface
The Main Menu
Figure 2 The Main Menu
-- VERILINK SCM CONTROLLER : FW Rev 1.18, Aug 24 1998 20:04:56 --
-- VERILINK SCM CONTROLLER : FW Rev 1.18, Aug 24 1998 20:04:56 --
Menu Heading Area
Shelf/Slot Map
Module Key
Command List
-- VERILINK SCM CONTROLLER : FW Rev 1.18, Aug 24 1998 20:04:56 ---- VERILINK SCM CONTROLLER : FW Rev 1.18, Aug 24 1998 20:04:56 - Site name: SCM Tutorial Access level: 2
Site name: SCM Tutorial Access level: 2
Site name: SCM Tutorial Access level: 2 Site name: SCM Tutorial Access level: 2
Managing at NEAR end node [0.0.0.2] Node id: 122
Managing at NEAR end node [0.0.0.2] Node id: 122
Managing at NEAR end node [0.0.0.2] Node id: 122 Managing at NEAR end node [0.0.0.2] Node id: 122
<- SLOT ->
<- SLOT ->
<- SLOT -> <- SLOT ->
SHELF 1 2 3 4 5 6 7 8 9 10 11 12 13
SHELF 1 2 3 4 5 6 7 8 9 10 11 12 13
SHELF 1 2 3 4 5 6 7 8 9 10 11 12 13 SHELF 1 2 3 4 5 6 7 8 9 10 11 12 13
0 - - - - - - - - - - - - -
0 - - - - - - - - - - - - -
0 - - - - - - - - - - - - - 0 - - - - - - - - - - - - 1 M [*S] D Q Q I M H - - - - - -
1 M [*S] D Q Q I M H - - - - - -
1 M [*S] D Q Q I M H - - - - - - 1 M [*S] D Q Q I M H - - - - - 2 - - - - - - - - - - - - -
2 - - - - - - - - - - - - -
2 - - - - - - - - - - - - - 2 - - - - - - - - - - - - 3 - - - - - - - - - - - - -
3 - - - - - - - - - - - - -
3 - - - - - - - - - - - - - 3 - - - - - - - - - - - - 4 - - - - - - - - - - - - -
4 - - - - - - - - - - - - -
4 - - - - - - - - - - - - - 4 - - - - - - - - - - - - KEY: D=QUAD D, I=IMUX, M=M13, Q=QUAD T1, S=SCM
KEY: D=QUAD D, I=IMUX, M=M13, Q=QUAD T1, S=SCM
KEY: D=QUAD D, I=IMUX, M=M13, Q=QUAD T1, S=SCMKEY: D=QUAD D, I=IMUX, M=M13, Q=QUAD T1, S=SCM
S) shelf/slot O) administration
S) shelf/slot O) administration
S) shelf/slot O) administrationS) shelf/slot O) administration
C) configuration D) diagnostics
C) configuration D) diagnostics
C) configuration D) diagnosticsC) configuration D) diagnostics
P) performance/status A) alarm
P) performance/status A) alarm
P) performance/status A) alarmP) performance/status A) alarm
B) circuit manager I) manufacturing info
B) circuit manager I) manufacturing info
B) circuit manager I) manufacturing infoB) circuit manager I) manufacturing info
X) logoff
X) logoff
X) logoffX) logoff
Figure 2 defines the parts of the Main Menu.
Firmware Version and Date of Release
Node Address
❷❸
❶
Using the Craft Inter face
Access Level (1-4)
A [0.0.0.2] [1,1] SCM >
A [0.0.0.2] [1,1] SCM >
A [0.0.0.2] [1,1] SCM >A [0.0.0.2] [1,1] SCM >
Active SCM Master Designator
❶
❷
❸
Interpreting the Main Menu
Node Address (Not IP Address)
Indicator for the type of shelf: M= Multi-line, D = Dual-line
Asterisk indicates that the SCM is the Shelf Controller
Brackets around module letter ( [P] ) indicate current module selected
Data (Command) Entry Area
The Main Menu shown in <HotSpot>Figure 2, provides:
a shelf/slot display showing card and shelf types and card
•
locations in each shelf
a key to the letters representing modules in the slots
•
a command list
•
node information
•
firmware revision number
•
Verilink Craf t Interface Craft-3
Using the Craft Inter face
The currently selected card is shown in the command line prompt
which returns after each command. The four-part number shown
on this line is
an Ethernet IP address. It is a Verilink-specific
not
node address used to identify this SCM or NCM.
Firmware Version
Shelf Symbols
Element Symbols
The firmware version revision nu mber appear s on the top lin e. The
controller modules have a revision number series different from
that of individual application modules.
NOTE: T h e revi sion numb ers shown in scree n sam ples are placeholders
only and do not reflect the revision numbers as they may appear in
your system. Firmware revision numbers vary according to several
factors, including special firmware generated for specific
customers, as well as current release versions.
Directly to the right of the Shelf column:
The M next to Shelf 2 indicates it is a multi-line shelf.
The D next to the Shelf 1 indicates it is a dual-line shelf.
Modules are represented in the node map by alphabetic char acters.
The key to these symbols is included in the Main Menu, beneath
the Shelf/Slot node map.
The shelf master is indicated by an asterisk (*). If a node controller
is present in the shelf, it is also the shelf master. (An exception is
an MLS 2200 shelf configured with independently-controlled
islands.) Some ACP-based modules are able to function as a shelf
master.
Selection Brackets
Brackets around a module symbol in the shelf ([N]) indicate that the
module is currently selected. For example, the brack ets around the
letter N in Figure 2 indicate that the NCM is currently selected.
A question mark (?) in place of a module symbol indicates that the
firmware or module is not recognized. Most likely the controller
module firmware is out o f date with the new module.
A hyphen (-) in place of a module symbol indicates that the module
has been pulled out of its slot since the last polling or that the
shelf/slot location you have selected is empty.
Craft-4 Verilink Craft Interface
Using the Craft Inter face
Command Line
Prompt
The initial prompt defaults to the module directly connected to the
Craft interface cable. The command line prompt is defined below:
[0.0.0.1] [0,11] NCM 2000 >
Where:
[0.0.0.1] is the node address of the node to which you are
connected. This number is used by modules and the Verilink
Node Manager application to identify a node. Each AS2000
node has a unique address. This value is completely unrelated
to an Ethernet IP address.
NOTE: The first three digits of the node address must NOT be greater than
127.
[0,11] is the shelf number and slot number of the currently
selected module. NCM 2000 is a sample of the command line
prompt, showing the model name of the currently selected
module.
This field reads UNKNOWN > when the shelf/slot location is
empty, the element has been removed, or if the module is not
recognized by a controller module.
Entering Commands
Conventions Used
Commands can be en t e re d in upper or lower case.
To clear a command entry mistake, exit from the command before
NTER
entering a complete pa rameter value by pressing E
To clear typed entries and start again, press C
backspace key can also be used to make corrections.
If you enter an invalid value, you will be prompted with a message
that the value is invalid and be returned to the current menu.
The Craft interface uses the following conventions:
In application modules with multiple network or data ports, an
•
is used to represent the port number. For example, to put
n
Port 2 in service, type “I 2” instead of “In”. In some older
modules “p” represents the port number.
Ranges of permitted values are depicted with ellipses. For
•
example, you can choose any number in the range 1 to 127
seconds to indicate the Alarm Declare Time. This is shown as
1..127. However, when you provide input indicating ranges,
do so with a dash: 1-24. This example indicates all numbers
between 1 and 24, includi ng the numbers 1 and 24. You can
also intermix single numbers with range definitions if they are
separated by commas, such as: 24, 38-45, 60.
ONTROL
.
-U. The
Fields
•
fields.
without
Verilink Craf t Interface Craft-5
a closed parenthesis, ), are status/information al
Using the Craft Inter face
A letter followed by a parenthesis, A), indicates a user-settable
•
option.
Selecting an
Element
To select an element in the node to manage, select the command
option for choosing the shelf and slot:
S) shelf/slot
as shown in the following example command line:
[0.0.0.1] [1,1] NCM 2000 > s
The next prompt shows you the for mat for your input.
For SCM and NCM :
Enter 'shelf,slot' pair or 'slot' in current shelf (e.g. 3,4 or 5): >
For SCC and NCC:
Enter 'shelf,slot' pair (e.g. 3,4 or 5): >
This prompt varies from product to product. Select the shelf and
slot location of the module to manage. In the example in Figure 3,
suppose you wish to configure a port on the DIDCSU loca ted in
shelf 2, slot 3. This element is represented by an A, which the Key
below the shelf/slot display identifies as a DIDCSU. You would type
in response to the prompt: “2,3”.
To indicate a successful selection, the Main Menu is redisplayed
with bracket-indicator [ ] moved to enclose the A.
Figure 3 Main Menu) with DIDCSU module selected
-- VERILINK NCM CONTROLLER : FW Rev 4.17, Dec 30 1997 16:55:20 --
Site Name: Test1 Access Level: 2
Managing at NEAR end node [0.0.0.1] Node ID: 3141
<- SLOT ->
SHELF 1 2 3 4 5 6 7 8 9 10 11 12 13
0 - - - - - - - - - - - - 1 M N *N - - Q M Q Q M - - - 2 M A A [A] A A A A A A A A - 3 - - - - - - - - - - - - 4 - - - - - - - - - - - - KEY: A=DIDCSU, B=DIU/DBU, C=CSU, D=DIU, E=SDIU, F=DIU/DDS, G=DHDM,
H=ATM/IMUX, I=IDCSU, J=PEP, K=DAC, L=HLM, M=IMUX, N=NCM, P=DPRI,
Q=QUAD, R=SUBRATE, S=HSM, T=HDM, U=DCSU, V=VCU, X=QPRI
S) shelf/slot O) administration
C) configuration D) diagnostics
P) performance/status A) alarm
B) circuit manager I) manufacturing info
X) exit this screen
A [0.0.0.1] [2,3] DIDCSU >
Craft-6 Verilink Craft Interface
Using the Craft Inter face
The command-line prompt reflects your selection in the shelf and
slot field (shelf 2, slot 3 in this case) and the card type (DIDCSU).
Exiting From the
Craft Interface
You can exit every menu by using the X command. Each time you
type “x”, you retur n to the next higher (p re vi o us ) menu.
At the Main Menu, typing X exits you from the Craft interface and
logs you off. If you started with the pSH+> prompt, you will be
returned to th e pSH+> prompt.
Sample Submenus
From the Main Menu, other functions such as configuration are
accessed through the submenus. The Configuration Menu
provides access to the menus used to configure ports, timing
options and other parameters. To access this menu from the Main
Menu, type “C” to display the Configuration Menu.
Figure 4 Configuration Menu
-- DIDCSU 2912 CONFIGURATION MENU -P) T1 port D) data port
T) timing options X) exit this screen
[1,1] DIDCSU 2912 >
In the above example, to access the T1 Port Configuration Menu,
type “P” from the Configuration Menu.
To change a port configuration (<HotSpot>Figure 5), enter the
parameter letter followed by the port number you want to change.
For example, to disable port 2 from service, type “I2”.
Verilink Craf t Interface Craft-7
Using the Craft Inter face
Figure 5 T1 Port Configuration Menu
-- DIDCSU 2912 T1 PORT CONFIGURATION MENU - PORT 1 PORT 2
In) In Service YES NO
Fn) Frame Format SF SF
Ln) Line Coding AMI AMI
Bn) Line Build Out 0db 0db
NDn) Network Density NONE NONE
NLn) Network Initiated Loop NO NO
An) Alarm Declare Time(sec) 0 0
DLn) FDL Enable NO NO
PRM Enable NO NO
Rn) Enable Inband NO NO
Sn) Inband Timeslot 1 1
F) FDL configuration X) exit this screen
[1,1] DIDCSU 2912 >i2
For application-specific menu options, see the application module
menus.
Craft-8 Verilink Craft Interface
Loading...