Verifone C680 User Manual

Verifone, Inc.

*DOC268-081-EN-B*

1-800-Verifone

www.verifone.com

Electrical

Power Packs

Before you connect the terminal power pack to an electrical outlet, check that the power switch on the terminal is turned off. If the te rminal d oes not have an o n/off sw itch, c heck
that the power cable connector is removed from the terminal’s power port. When connecting the terminal to a power pack, always connect the plug of the power pack to an
electrical wall outlet first, then connect the power cable to the terminal’s power port.
The power pack is rated as follows:

• Input Voltage: 100 - 240V AC, 50/60Hz

• Output Voltage: 5V DC, 2.2A
Model C680 3G/C680 3G-BT-WiFi is intended to be provided with a Listed Power supply module having an output rating of 5V DC, minimum 2.2A, Tma 40°C, class II and
evaluated as a Limit ed Power Source or PS2 or equival ent.

AC Adapter

The AC adapter is d esigned to ensure your personal safety and to be compatible with this equipment. Please follow these guidelines:

• Do not use the adap ter in a high moisture environment . Never touch the adapter when your hands or feet are wet.

• Allow adequate ventilation around the adapter. Avoid locations with restricted airflow.

• Connect the adapter to a proper power source. The voltage and grounding requiremen ts are found on the product case and/ or packaging.

• Do not use the adapter if the cord becomes damaged.

• Do not attempt to service the adapter. There are no serviceable parts inside. Replace the unit if it is damaged or exposed t o excess moisture.

Peripherals

Before connecting any peripheral devic e, turn off power to the terminal and check that the power cable connector is removed from the terminal’s power port. Turn on power only
after you are finished co nnecting the peripheral device(s). F or complete information about peripheral installation and use, please refer to the user docume ntation supplied with
those devices.

Disconnecting Power

Disconnecting power during a transaction may cause transaction data files that are not yet stored in terminal memory to be lost.

Location – Electrical Considerations

CAUTION: Due to risk of electrical shock or terminal damage, do not use the terminal near water, including a bathtub, wash bowl, kitchen sink or laundry tub, in a wet

ATTENTION: Du fait d'un risque d'électrocutio n ou d'une d étério ration du t erminal, ne pas utilise r cet équi pement p rès d'un e source d'eau, p ar exemple près d'une baignoire,

basement, or near a swimming pool. Also, avoid using this product during electrical storms. Avoid locations near electrical appliances or other devices that
cause excessive voltage fluct uations or emit electrical noise (for example, air conditioners, neon signs, high-frequency or magnetic security devices, or electric
motors).

d'un lavabo, d'un évier de cuisine ou d'un bac de lavage, dans un sous-sol humide ou à proximité d'une piscine. De même, éviter d’utiliser ce produit lors des
orages provoquant des coupures él ectrique s.Éviter de place r le term inal à pro ximité d’a ppar eils él ectriques ou autres un ités pouvant entraîner des fluctuations
de tension importantes ou des interférences électriques, tels que les climatiseurs, enseignes au néon, dispositifs de sécurité à haute fréquence ou
équipements électriques.

Equipment

Repairs

Do not, under any circumstances, attempt any service, adjustments, or repairs on this equipment. Instead, contact your local Verifone distributor or service provider for
assistance. Failure to comply may void the product warranty.

Location – Environmental Considerations

Do not plug the power pack into an outdoor outlet or operate the terminal outdoors. It is not waterproof or dustproof, and is for indoor use only. Any damage to the unit from
exposure to rain or dust may void your warranty. Do not use the terminal where there is high heat, dust, humidity, moisture, or caustic chemicals or oils. Keep the terminal away
from direct sunlight and anything that radiates heat, such as a stove or a motor.
WARNING! Your POS Terminal contains sensitive electronic components that can be permanently damaged if exposed to excessive shock or vibration. To minimize the

AVERTISSEMENT! Votre terminal de point de vente contient des composants électroniques sensibles, susceptibles de subir des dommages définitifs en cas d'exposition à

risk of damage to your Terminal, avoid dropping your Terminal and operating it in high-shock and high-vibration environments. Do not store the Terminal
where prolonged exposure to extreme temperature can occur, because it can cause permanent damage. Do not expose the Terminal to water. Contact with
water can cause this unit to malfunction.

des chocs ou à des vibrations excessives. Pour minimiser le risque de dommages pour votre terminal, éviter de le faire tomber ou de l'exposer à des
environnements pouvant provo quer des chocs e t des vib ration s exce ssives. N e pas stock er le termi nal dans des lie ux susc eptible s d'entraîner une exposition
prolongée à des températures extrêmes, du fait des dommages définitifs que cette situation peut provoquer. Ne pas exposer le terminal à l'eau. Un contact
avec de l'eau peut provoquer un dysfonctionnement de l'unité.

Battery Instructions

Dispose of the battery pack in accordance with all national, state, and local laws and regulations as regionally required. Some batteries may be recycled and may b e accepted
for disposal at local recycling centers.
CAUTION: There is risk of explosion if the battery is replaced by an incorrect type.

ATTENTION: Il existe un risque d'explosion si la batterie est remplacée par un modèle incompatible.

– Leaving a battery in an extremely high temperature s urrounding environment that can result in an explosion or the leakage of flammable liquid or gas .
– A battery subjected to extremely low air pressure that may result in an explosion or the leakage of flammable liquid or gas.
The highest specifie d charging temperature of battery pac k is 50+/-3°C.
The lowest specified charging temperature of battery pack is 3+/- 3°C.

Operating Temperature

The product is designed to work in maximum ambient temperature 0°C and 40°C.

C680 3G and C680 3G-BT-WiFi Certifications and Regulations

FCC Compliance

The following device has been tested and certified as compliant with the regulation and guidelines set forth in Part 15 of FCC Rules:
Manufacturer: Verifone, Inc.
Brand: Verifone
Model: C680 3G, C680 3G-BT-WiFi

Part 15 of FCC Rules

This device complies with the limits for a Class B digital device as specified in Part 15 of FCC Rules, which provides reasonable protection against harmful interference in a
residential installation.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference received, including interference that may cause undesired operation.
Any changes or modifications to this equipment not expressly approved by Verifone could void the user's authority to operate this equipment.
This equipment gener ates, uses, and can radiate radi o frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to
radio communication s. However, there is no guarantee that interference will not occur in a particular installation. In the unlikely event that there is interference to radio or
television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

- Consult the dealer or an experienced radio/TV technician for help.
This device and its antenna(s) must not be co-located or operating in conjunction with any other antenna or transmitter. Use of a shielded interface cable is required to comply
with the Class B limits of Part 15 of FCC Rules. Any changes or modifications to this equipment not expressly approved by Verifone could void the user's authority to operate
this equipment.

NOTE: The country code selection is for non-US model only and is not available to all US model. Per FCC regulation, all WiFi product market in US must fixed to US

operation channels only.

Notice for WLAN

For CE WLAN:5150-5350 MHz
This device is restricted for indoor use only when operating in the 5150 to 5350 MHz frequency range.

AT BE BG HR CY CZ DK EE

FI FR DE EL HU IE IT LV

LT LU MT NL PL PT RO SK

SI ES SE UK IS LI NO CH

TR

Notice for Operating Frequency and Output Power

μA/m at 10m), 13.56MHz

NFC (dB

2.4 G WLAN: 802.11 b/g/n (EIRP dBm)
2412-2472 MHz

5G WLAN: 802.11a/n20/n40 (EIRP dBm)
5180-5240MHz, 5260-5320MHz; 5500-5700MHz

BT- EDR/LE (EIRP dBm)
2402-2480MHz

2G GSM900/GSM1800 (dBm) EGSM: 33/ DCS: 30.9

3G Band I/Band VII I(dBm)

Feature

RF Exposure

USA

The product comply with the FCC portable RF exposure limit set forth for an uncontrolled environment and are safe for intended operation as described i n this manual. The
further RF exposure reduction can be achieved if the product can be kept as far as possible from the user body or set the device to lower output power if such function is
availab le. The SAR li mit set by the F CC is 1.6W/kg f or body worn SAR and 4W/kg for extremity SAR. Tests for SAR are conducted using standard operating positions accepted
by the FCC with the device transmitting at its highest certified power level in all tested frequency bands. This device has been tested and meets the FCC RF exposure
guidelines be positioned a minimum of 0cm from the body.
This device complie s with SAR for general populat ion/uncontrolled exposure limits in ANSI/IEEE C95.1-1999 and has been tested in accordance with the measurement
methods and procedures specified in OET Bulletin 65 Supplement C.

CE

This device complies with the Radio Equipment Directive (2014/53/EU) issued by the Co mmission of the European Community.
A minimum separation distance of 0cm must be maintained between the user’s body and the device, including the antenna during body-worn operation to comply with the RF
exposure requirem ents in Europe.

Legal Terms and Conditions Regarding PCI SSC Approvals

PCI SSC’s approval only applies to PEDs that are identical to the PED tested by a PCI Security Standards Council recognized laboratory. If any aspect of the PED is different
from that which was tested by the laboratory - even if the PED conforms to the basic product description contained in the letter, then the PED model should not be considered
approved, nor promoted as approved. For example, if a PED contains firmware, software, or physical construction that has the same name or model number as those tested by
the laboratory, but in fact are not identical to those PED samples tested by the laboratory, then the PED should not be considered or promoted as approved.
No vendor or other third party may refer to a PED as “PCI Approved,” nor otherwise state or imp ly that PCI SSC has, in whole or part, approved any aspect of a vendor or its
PEDs, ex cept to the ex tent and subje ct to the terms and restrictions expressly set forth in a written agreement with PCI SSC, or in an approval letter. All other references to PCI
SSC’s approval are strictly and actively prohibited by PCI SSC.
When granted, an approval is provided by PCI SSC to ensure certain security and operational characteristics important to the achievement of PCI SSC’s goals, but the
approval does not under any circumstances include any endorsement or warranty regarding the functionality, quality, or performance of any particular produ ct or services. PCI
SSC does not warrant any products or services provided by oth er third parties. Approval does not, under any circumstances, include or imply any product warranties from PCI
SSC, including, without limitation, any implied warranties of merchantability, fitness for purpose or non-infringement, all of which are expressly disclaimed by PCI SSC. All rights
and remedies regarding products and services, which have received an approval, shall be provided by the party providing such products or services, and not by PCI SSC or the
payment brand participants.

Brazil Warning Statement

This equipment operates on a secondary basis, and must not cause interference to systems operating on a primary basis. As a secondary equipment, it is not protected from
harmful interfer ence, even from stations of th e same type.

This equipment may be operated in:

C680 3G C680 3G-BT-WiFi

6.41 7.52

NA 11b: 12.21/ 11g: 12.51 / 11n-HT20: 12.31

NA 11a: 15.06/ 11n-HT20: 15.00/ 11n-HT40: 15.22

NA EDR: 11.61/ LE: 6. 61

Band I: 23.3/ Band VIII: 23.6

C680 3G and C680 3G-BT-WiFi Certifications and Regulations

Verifone Part Number: DOC268-081-EN-B, Revision B01

© 2020 Verifone, Inc. All rights reserved.

Recycling: DO NOT DISCARD!

UNIT MUST BE RECYCLED OR DISPOSED OF PROPERLY
For proper disposal instructions, go to http://recycle.verifone.com Please retain this sheet for future reference.

continued on rear cove r

Recyclage: NE PAS JETER!

L'unité doit être recyclée ou mise au rebut dans les endroits prévus à cet effet.
Pour connaître les procédures de mise au rebut, consultez le site http://recycle.verifone.com À conserver pour référence ultérieure.

suite au verso

C680 3G and C680 3G-BT-WiFi Declaration of Conformity

DECLARATION OF CONFORMITY

according to ISO/IEC 17050-1 and 17050-2

This declaration of conformity is issued under the sole responsibility of the manufacturer

_______________________________________________________________ _______________________

Manufacturer’s Name Verifone, Inc.

Manufacturer’s Address Verifone, Inc.

Declares, that the product

Product Name:

Model Number:

Part Number:

Brand:

Product Options:

SW Version:

NB Company Name:

NB Company Number:

Certificate Number:

C680 3G C680 3G-BT-WiFi

QT0002EH 04.003

CTC advanced GmbH CETECOM ICT Services GmbH

0682 0682

T818602L-01-TEC M529654D-01-EO

C680

M268-8XX-XX-XXX

Verifone

All

Conforms to the following product specifications:

Regulatory Requirement

Safety:

EMC:

RF (RFID):

RF (WiFi/BT):

RF (2G/3G):

SAR:

Standards

IEC 60950-1:2005 + A1:2009 + A2:2013
EN 60950-1:2006 + A11:2009 + A1:2010 + A12:2011 + A2:2013
IEC 62368-1:2014
EN 62368-1:2014 + A11:2017

EN 55032:2012 + AC:2013, Class B
EN 55032:2015 + AC:2016, Class B
EN 61000-3-2:2014, Class A
EN 61000-3-3:2013
EN 55035:2017

Final Draft EN 301 489-1 V2.1.1
Draft EN 301 489-1 V2.2.0
EN 301 489-3 V2.2.1
EN 300 330 V2.1.1

Final Draft EN 301 489-1 V2.1.1
Draft EN 301 489-1 V2.2.0
Draft EN 301 489-17 V3.2.0
EN 300 328 V2.1.1
EN 301 893 V2.1.1

Final Draft EN 301 489-1 V2.1.1
Draft EN 301 489-1 V2.2.0
Draft EN 301 489-52 V1.1.0
EN 301 511 V12.5.1

EN 301 908-1 V11.1.1
EN 301 908-2 V11.1.2

EN 301 908-1 V13.1.1 X

EN 50566:2017
EN 62311:2008
EN 62209-2:2010
EN 62479:2010
EN 50663:2017
EN 50665:2017

1400 West Stanford Ranch Road
Suite 200 Rocklin, CA 95765

C680 3G C680 3G-BT-WiFi

XX

XX

XX

X

XX

XX

XX

Supplementary Information:

We hereby declare that the device complies with the requirements of Radio Equipment Directive 2014/53/EU. This product carries the CE Mark per Directive (93/68/EEC)
and conforms to RoHS Directive 2011/65/EU and delegated Directive (annex II) 2015/863/EU, as well as Technical Documentation: EN 50581:2012 and DIN EN 50581
(2013-02).

CE Approval Date: December 04, 2020

Phil Baldock
Executive Vice President, Global Operations,
Atlanta, GA, USA

European contact for regulatory topics only: Verifone UK Ltd.

3 Roundwood Avenue
Stockley Park
Uxbridge Middlesex UB11 1AF UK
Tel: [phone]