Page 1
®
SPL
Series
i
SPL-800i
SPL-1000i
USER’S
MANUAL
Audio/Video Subwoofer System
Page 2
.
www.velodyne.com
SPLi Series User’s Manual
i
Page 3
Table of Contents
C
ongratulations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
Prepare for Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
Line-Level Connection - Option A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
Line-Level Connection - Option B . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
Speaker-Level Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
Interconnnect Cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
Care of Your Subwoofer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
Protection Circuitry . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
Troubleshooting and Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
Velodyne Products . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
.
www.velodyne.com
SPLi Series User’s Manual
ii
Page 4
Restoring Defaults
Congratulations
C
ongratulations on your purchase of a Velodyne subwoofer system. This system represents the
state-of-the-art in low frequency reproduction and will provide you with years of listening
pleasure when properly cared for. Read and follow this instruction manual to insure safe and
proper system connection and operation.
Caution!
Please observe the following precautions to insure safe and proper system operation.
Note: Do not leave unit in direct sunlight or use in high humidity environments!!!
Warning!
To prevent fire or shock hazard, do not expose this equipment to rain or moisture. To avoid
electrical shock, do not open speaker enclosure or amp chassis cover. Please observe all
warnings on the equipment itself. There are no user serviceable parts inside. Please refer all
service questions to your authorized Velodyne dealer or service representative.
Prior to Installation
Please unpack the system carefully. This unit is heavy. Use caution when lifting or moving to
avoid injury. Please save the carton and all packaging materials for future use. Packing this unit
in any other carton may result in severe damage when shipping. Record the serial number in
the space provided on the warranty card for future reference.
oduct Features and Controls
Pr
• 230 V
• A single driver consisting of either:
- 8” (6.5” piston diameter) driver with 2.5” high-temp voice coil and
204 ounce magnet structure or,
- 10” (8” piston diameter) driver with 3” high-temp voice coil and
346 ounce magnet structure
• Built-in 2000 watts Dynamic/1000 watts RMS high efficiency Class D amplifier
• Adjustable (40 to 120 Hz) low-pass crossover (defeatable)
• Line-level (RCA) inputs and outputs
• LFE Input
• Speaker-level inputs with five way binding post connections
• Signal sensing auto turn on/off (defeatable)
• Variable volume control
• Selectable phase control (0° or 180°)
• Multiple staggered low-pass crossovers; 12 dB/octave initial, 48 dB/octave ultimate
cuit pr
Driver Displacement Contr
•
• Blue power indicator LED
• High-excursion r
• Oversized spider for linearity at high excursion
ubber sur
ol cir
round
events over excursion and amp clipping
.
www.velodyne.com
SPLi Series User’s Manual
1
Page 5
Prepare for Installation
Y
our new Velodyne subwoofer provides for a number of installation options. Read all the
installation information below in order to determine which installation option is best suited for
your system.
off to prevent possible damage.
PLACEMENT
True subwoofers operate at extremely low frequencies which are primarily omni-directional.
While it is recommended that the subwoofer be placed on the same plane as the satellite
speakers, room and system conditions often dictate otherwise. Keep in mind that frequency
response and output level can be drastically influenced by placement, depending on the acoustic
properties of the listening room. Typically, the optimum location for a subwoofer is tucked away
in a corner of your listening room. This location will usually offer the greatest output levels and
optimum low frequency extension. The worst location for a subwoofer is typically far away from
any walls and close to the center of your room. Avoid these locations when possible. When
using a pair of Velodyne subwoofers in stereo, it is preferable to place each subwoofer by the
satellite of the same channel.
Caution! This subwoofer has electronics built into the cabinet. Do not place the cabinet
next to sources of heat such as furnace registers, radiators, etc. Do not place the unit
near sources of excessive moisture, such as evaporative coolers, humidifiers, etc. The
power cord should be routed in such a way that it will not be walked on, pinched or
compressed in any way that could result in damaging the insulation or wire.
Remember to perform all installation procedures with system power turned
Regar
(woofer facing forward). Using, shipping or storing the subwoofer in any other position for an
extended period of time may result in damage to the unit not covered by war
Your new Velodyne subwoofer, like any good speaker system, requires proper positioning within the
listening space to provide maximum performance. Improperly placed speakers may degrade the
sound quality and reduce your listening pleasure. Depending on the size and type of furnishings in
the room, perfect placement may not be possible. Finding the best location within your
environment will likely require some experimentation. We suggest you experiment with the location
during setup to find what sounds best to you when seated in your typical listening position.
dless of where you install your Velodyne subwoofer, it must remain in an upright position
ranty.
.
www.velodyne.com
SPLi Series User’s Manual
2
Page 6
Installation
Inputs
Your new subwoofer is equipped with speaker-level and line-level inputs. Use the LINE LEVEL
jacks when connecting your subwoofer to a pre-amp, signal processor, line-level crossover or
receiver with pre-amp level outputs. The
outputs of any amplifier, integrated amplifier or receiver. Your amplifier section will notice no
additional loading effects when you use these inputs due to their very high impedance.
Important!!!
Do not use both LINE LEVEL and SPEAKER LEVEL connections simultaneously!
Volume Control
This control allows you to balance the output from the subwoofer to the main
speakers/amplifier in your system. This control should be set to achieve similar output level
from both the main speakers and subwoofer when listening to music. A good starting point for
the volume control is 3 or 4 dots from minimum.
Low-pass Crossover - 40 to 120 Hz
All inputs sum the left and right channels together, with the r
adjustable low-pass crossover before being amplified. The crossover control allows you to adjust
the upper limit of the subwoofer’s frequency response from 40 to 120 Hz. The subwoofer’s
response will begin rolling off above the frequency you set this control to. You should set the
crossover frequency to obtain a smooth and seamless transition from the subwoofer to the
main speakers in your system. If your main speakers are smaller units with limited low frequency
output, you may wish to choose a higher frequency (such as 100 -120 Hz) than you would with
ger speakers which have gr
lar
with this contr
ol set lower, such as 80 Hz.
eater low frequency output. With lar
SPEAKER LEVEL jacks connect directly to the speaker
esulting signal passing through an
ger speakers, you might start
A bypass switch is also pr
an exter
optimum performance!
nal crossover, we recommend that you use the one provided within the unit for
ovided if you wish to use an exter
nal crossover
.
If you ar
e not using
Phase Adjustment - 0°/180°
to cor
This contr
for any possible mismatch and resulting cancellation between the subwoofer and your main
speakers/amplifier
switch fr
correct position will have a greater amount of apparent low frequency output.
ol allows you to “r
. T
om one position to the other and listen for a change in low fr
everse” the phase of the subwoofer’
o adjust, simply listen to the system with music playing. Then move the
s output signal 180
equency output. The
°
rect
Crossover Switch - INTERNAL X-OVER/SUBWOOFER DIRECT
This switch allows the internal crossover circuitry to be removed from the signal path. This is
required in certain installations which route the signal through external processors with a
ossover cir
cr
SUBWOOFER DIRECT to disengage the built-in crossover. For all other installations which do
not have a separate electr
INTERNAL X-OVER to provide optimum performance.
cuit of their own, such as the new digital units. Simply move the switch to
onic cr
ossover, we recommend you leave the switch set to
.
www.velodyne.com
SPLi Series User’s Manual
3
Page 7
Signal Sensing Auto Turn On/Off Function
With this function in the “standby” position, your subwoofer can be safely left with the main
p
ower switched on continuously. The subwoofer will turn itself on automatically when an audio
signal is present. If no signal is present for approximately 10 minutes, the unit will switch to
standby mode. While in standby mode, your subwoofer will draw very minimal power. This
function can be disabled by leaving the switch in the “always on” position.
Power Switch
The master power switch is located on the lower half of the unit. This rocker style switch is the
main on/off for the unit. This switch should be set to position 1 (up) for on, and 0 (down) for
off. If the unit is to be left unused for an extended period of time, the master power switch
should be turned off.
Subwoofer Outputs
The Velodyne subwoofer is designed to operate using the full range audio signal for input when
using the built-in crossover. Some processors/receivers have a “subwoofer out” jack that is
internally filtered and designed to be used with a conventional amplifier and speaker. In some
rare cases, combining both an external crossover and the one internal to the subwoofer may
result in low output and increased noise. In these installations you may need to bypass the
internal crossover in either the processor or Velodyne subwoofer. In some installations, simply
setting one crossover to a higher frequency (such as 120 Hz) will restore maximum
performance. To bypass the subwoofer’s internal crossover when the unit is being fed a low
pass signal from another crossover, simply locate the switch marked
X-OVER/SUBWOOFER DIRECT
SUBWOOFER DIRECT position. This will eliminate the internal crossover from the signal path.
on the rear panel of the subwoofer and set to the
INTERNAL
Note: If not using an external crossover, you should use the built-in crossover for
optimal performance.
LINE-LEVEL CONNECTION - OPTION A
Figure 1 shows connection from your home theater receiver to the LFE input on the back of
your subwoofer. When the subwoofer is installed in this fashion, all of the low frequency
mation fr
infor
your Velodyne subwoofer. This connection is the most common connection method when using
your subwoofer with a 5.1 receiver. (Cable needed: 1 mono RCA cable.)
om your “LFE Out” or “Subwoofer Out” on the back of your receiver will pass into
.
www.velodyne.com
SPLi Series User’s Manual
4
Page 8
NOTE: SPL-800i is
identical in features
and layout to the
SPL-1000i shown.
Figure 1. Installation Using LFE Line-Level Inputs
Note: If not using an external crossover, you should use the built-in crossover for
optimal performance. When using a single channel input (such as a surround sound
cuit sensitivity will be affected.
ocessor’
pr
When one input channel is used instead of two, the unit will see lower signal levels
esent at the inputs. This may cause the unit to tur
pr
levels. If this occurs, simply use a “Y” adapter (available from most dealers) to allow
your processor’s single sub line to be fed into both L&R inputs. This will make the unit
turn on at lower signal levels.
.
www.velodyne.com
s subwoofer out or LFE), the auto on/of
f cir
n off when listening at low volume
SPLi Series User’s Manual
5
Page 9
LINE-LEVEL CONNECTION - OPTION B
F
igure 2 shows connection from a pre-amplifier’s main outputs to the left and right inputs of
your Velodyne subwoofer. You will also need to connect a second pair of RCA cables from the
outputs on the back of your subwoofer to the inputs on the back of your amplifier. When the
subwoofer is installed in this fashion, your satellite speakers will be crossed over at 80 Hz which
removes the lower bass frequencies from your external amplifier and speakers, enabling them
to do a better job reproducing the higher frequencies. By utilizing this method, you will have a
bi-amplified system, gaining improved power and headroom for your system. This installation
method is not as common as the method described in Figure 1. (Cables needed: 2 stereo pair
of RCA cables.)
NOTE: SPL-800i is
identical in features
and layout to the
SPL-1000i shown.
Figure 2. Installation Using Stereo Line-Level Inputs
.
www.velodyne.com
SPLi Series User’s Manual
6
Page 10
Speaker-Level Connections
F
igure 3 shows an easy way to connect your Velodyne subwoofer directly to your receiver or
integrated amplifier, if it lacks line-level outputs. You may also connect your satellites directly to
your receiver or amplifier along with the subwoofer. Your receiver or amplifier will not notice the
additional load of the subwoofer due to the high input impedance.
NOTE: SPL-800i is
identical in features
and layout to the
SPL-1000i shown.
Figure 3. Installation Using Speaker-Level Inputs
Caution!!! T
when making all connections. Red (positive) to red, and black (negative) to black. Be
sure that all connections are tight, and that there are no loose strands or frayed wires.
.
www.velodyne.com
o avoid damage to your main amplifier, be sure to maintain correct polarity
SPLi Series User’s Manual
7
Page 11
Interconnect Cables
W
hen installing your new Velodyne subwoofer using the line level connections, you should always
use shielded phono cables. There are many decent cables available today, most any of which
will work perfectly well. We do recommend that you keep the length of cable as short as
possible to avoid any potential noise problems.
When using speaker level connections, use a decent quality speaker cable that mates well with
the connectors. Be very careful to avoid any loose strands or frayed wires which may result in
a short, which may damage your equipment. Cables of extremely large size are typically not
required. Extremely large gauge wire may not properly fit in the binding posts, resulting in a
poor connection and possible short circuits.
Care of Your Subwoofer
Your Velodyne subwoofer does not require any regular maintenance. Normal dusting or cleaning
of the surface for appearance purposes are all that is required. We suggest you avoid any harsh
detergents or chemicals when cleaning the cabinet. Abrasives, detergents, or cleaning
solutions may damage the finish on the cabinet. We recommend using only a damp cloth to
clean the cabinet.
During nor
oblems. The unit is equipped with a signal-sensing turn on/ off that will automatically turn on
pr
the unit when a signal is present at the inputs and turn of
there is no longer any signal at the inputs. If you plan to leave the subwoofer unused for
an extended period of time, we recommend that you turn off the master power switch on the
rear panel.
mal conditions, your new subwoofer may be left on continuously without any
f the unit after several minutes when
Pro tection Circuitry
Your new subwoofer is equipped with special protection circuitry to provide maximum
performance with greatest reliability.
The unit is protected against:
1) Overdriving the speaker or amplifier
2) Over
3) Excessive drop in power line voltage
The first type of pr
operates constantly without being audible under most situations. In some extreme situations
(sustained high output levels such as pro sound usage), the unit may shut down momentarily.
This indicates the thermal or under-voltage protection circuitry has engaged. If this should
happen, you should reduce the volume setting or shut the unit off until normal operating
conditions return. You may also want to plug the unit into a different wall outlet, as dropping
power line voltage will be most noticeable under str
shutting down intermittently.
heating the amplifier
otection circuitry which prevents overdriving of the speaker or amplifier
enuous conditions and may r
esult in the unit
.
www.velodyne.com
SPLi Series User’s Manual
8
Page 12
Troubleshooting and Service
B
efore seeking service for your amplifier or subwoofer, please re-check all systems. Following
is a simple troubleshooting guide to assist you.
1. Verify that the unit is plugged in and power outlet used is active.
2. Is the power switch on?
3. Is the unit receiving an input signal from your source?
4. Have all controls (volume, crossover, phase, etc.) been properly set?
5. If the unit has been running at high levels, one of the protection circuits may be engaged.
Has the amplifier overheated?
6. Make sure binding posts are tightened.
If the protection circuitry is active, the unit may cycle on and off until operating parameters
return to normal. Under more serious conditions, the unit may shut off completely. Normal
operation should return upon cooling, but you may be required to turn the power off and then
on again to reset the unit.
The following conditions require service by a qualified technician:
1. The power cord has become damaged
2. The unit does not appear to operate normally or exhibits a marked
change in performance
3. The unit has been exposed to water
4. Some par
t of the chassis or circuitry is physically damaged
Thank You for Purchasing a Velodyne!
.
www.velodyne.com
SPLi Series User’s Manual
9
Page 13
Specifications
Specifications SPL-800i SPL-1000i
Woofer 8” forward firing 10” forward firing
(6.5” piston diameter) (8” piston diameter)
Amplifier 2000 watts Dynamic 2000 watts Dynamic
(Class D) 1000 watts RMS Power 1000 watts RMS Power
High Pass Crossover 80 Hz (6 dB/octave) 80 Hz (6 dB/octave)
Low Pass Crossover 40 Hz-120 Hz 40 Hz-120 Hz
12 dB octave initial, 12 dB octave initial,
48 dB octave ultimate 48 dB octave ultimate
Frequency Response 28-120 Hz (+/-3 dB) 23-120 Hz (+/-3 dB)
Harmonic Distortion <5% (typical) <5% (typical)
Magnet Structure 204 oz. 346 oz.
(12.7 lbs) (21.6 lbs)
Voice Coil 2.5” Dual Layer 3” Dual Layer
inner/outer wind inner/outer wind
Inputs Line and Speaker Level Line and Speaker Level
Outputs Line-level, 80 Hz up Line-level, 80 Hz up
Phase 0° or 180° 0° or 180°
Video Shielded No Yes
Dimensions (H/W/D) 10.9” x 10.4” x 12.8” 12.9” x 12.4” x 14.5”
(inc. feet, grille and knobs) (27.7 x 26.4 x 32.5 cm) (32.8 x 31.5 x 36.8 cm)
Cabinet
ranty (parts/labor) Three years (electronics) Three years (electronicsr)
ar
W
th America)
(Nor
Shipping W
eight (approx.) 33 lbs. (15 Kgs) 45 lbs. (20 Kgs)
Sealed enclosur
Five years (drivers)
e
Sealed enclosur
Five years (drivers)
e
.
www.velodyne.com
SPLi Series User’s Manual
10
Page 14
FOR YOUR RECORDS. . .
Date Purchased_________________________________________________________________
Dealer_________________________________________________________________________
Serial #________________________________________________________________________
*NOTE: Please complete and return your warranty card within ten (10) days or
Register. . . ON LINE . . . It’s faster . . . and easier
www.velodyne.com
LIMITED WARRANTY - U.S. AND CANADA ONLY
VELODYNE ACOUSTICS, Inc. (“VELODYNE”) warrants all electronics for a period of three years, drivers for a period
of five years, and full range speakers for a period of five years. All VELODYNE products have a warranty from the
date of purchase against defects in materials and workmanship subject to the following conditions:
1. VELODYNE is not responsible for defects which result from the use of an amplifier or controller other than
the one originally supplied with the unit (subwoofer) or defects which result from modifications or repairs
made by any component of the system by anyone other than a VELODYNE factory authorized
service representative.
2. This warranty is void if any repairs or service covered by the terms of this warranty are made to any
component of the system by anyone other than a VELODYNE factory authorized service representative.
3. VELODYNE is not responsible for damage caused by accidents, abuse, misuse, natural or personal disaster
or unauthorized modification. The VELODYNE products are not intended for professional or commercial use
and VELODYNE is not responsible for damage resulting from such use.
4. The VELODYNE product warranty is limited to units that are purchased from authorized VELODYNE dealers
and finalized within authorized dealer locations.
5. This warranty is nontransferable under any condition.
6. Use of this product outside the U.S. and Canada voids this warranty.
TO OBTAIN SER
Information regarding service may be obtained from the dealer from whom you purchased the unit, or by contacting
VELODYNE customer ser
representative within the warranty period set forth above. If VELODYNE determines the unit is defective, VELODYNE
will, at VELODYNE’s option, repair or replace the product at no charge if the product is forwarded prepaid to a factory
authorized service representative. Products forwarded to the factory authorized service representative should be
shipped securely and properly packaged, insured and freight prepaid.
ARRANTY OUTSIDE THE UNITED STATES AND CANADA
W
ranty of this pr
ar
The W
applicable law and shall be the sole responsibility of the distributor that supplied this product. To obtain any applicable
ranty ser
war
this product.
vice, please contact the dealer fr
vice. W
oduct if it is sold to a consumer outside of the United States or Canada shall comply with
arranty ser
vice must be perfor
om which you pur
VICE
med by a VELODYNE factory authorized service
chased this pr
oduct, or the distributor that supplied
.
www.velodyne.com
SPLi Series User’s Manual
11
Page 15
Velodyne Products
115 - 120V
®
D
D Series
DD-10
DD-12
DD-15
DD-18
Digital Drive 1812
Signature Edition
DEQ-R Series
DEQ-8R
DEQ-10R
DEQ-12R
DEQ-15R
DLS™-R Series
MiniVee
MiniVee®10
Optimum Series
Optimum-8
Optimum-10
Optimum-12
SMS™-1
SubContractor™
Series
SC-1250
SC-10
SC-12
®
220 - 240V
®
DD Series
DD-10
DD-12
DD-15
DD-18
Digital Drive 1812
Signature Edition
CHT-Q Series
CHT-8Q
CHT-10Q
CHT-12Q
CHT-15Q
Impact Series
SPLi Series
SPL-800i
SPL-1000i
SPL-Ultra Series
SPL-800 Ultra
SPL-1000 Ultra
SPL-1200 Ultra
SubContractor™
Series
SC-1250
SC-10
SC-12
SC-15
DLS -3500R
DLS -3750R
DLS -4000R
DLS -5000R
Impact Series
Impact - Mini
Impact -10
Impact -12
MicroVee™
SC-15
SC-IW
SC-IF/IC
SC-600 Amp
SC-602 Amp
SC-600 IW
SC-600 IF/IC
VX-11
Impact - Mini
Impact -10
Impact -12
MicroVee™
SMS™ -1
SC-IW
SC-IF/IC
SC-600 Amp
SC-602 Amp
SC-600 IW
SC-600 IF/IC
.
www.velodyne.com
SPLi Series User’s Manual
12
Page 16
63-SPLi Rev B JUN10
.
www.velodyne.com
Velodyne Acoustics, Inc.
Morgan Hill, CA 95037
408.465.2800 voice
408.779.9208 ser
Service E
Product E
Technical E
345 Digital Drive
408.779.9227 fax
vice fax
www
.velodyne.com
-mail: service@velodyne.com
-mail: help@velodyne.com
-mail: techhelp@velodyne.com
SPLi Series User’s Manual
13
Loading...