Velodyne Acoustics SC-600 IF-IC, SC-600D User Manual

SC-600D Amplifier
SubContractor™ Series
U S E R ’ S
M A N U A L
S C - 6 0 0 D A m p l i f i e r, S C - 6 0 0 I W, S C - 6 0 0 I F / I C Subwoofers
C a u t i o n !
'&"!
To reduce the risk of electric shock, do not remove cover (or back). No user-serviceable parts inside. Refer servicing to qualified service personnel.
The lightning flash with arrowhead symbol is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.
The exclamation point symbol is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the subwoofer.
1. !%&$'&"!%, All safety and operating instructions should be read before the product is operated.
2. &!!%&$'&"!%, The safety and operating instructions should be retained for future reference.
3. $!!%, All warnings on the product and in the operating instructions should be adhered to.
4. "")!%&$'&"!%,All operating and use instructions should be followed.
5. &$!"%&'$, The product should not be used near water — for example, near a bathtub, washbowl, kitchen sink, laundry tub, in a wet basement, near a swimming pool or the like.
6. $&%!&!%, The product should be used only with a cart or stand recommended by the manufacturer. If a cart is used, use caution when moving the cart/product to avoid injury from tip-over.
7. "$!"'!&!, The product should be mounted to a wall or ceiling only as recommended by the manufacturer.
8. !&&"!, The product should be situated so that its location or position does not interfere with its proper ventilation. For example, the product should not be situated on a bed, sofa, rug, or similar surface that may block the ventilation openings; or placed in a built-in installation such as a bookcase or cabinet that may impede the flow of air through the ventilation openings. The ventilation shall not be impeded by covering the ventilation openings with items such as newspapers, tablecloths, curtains, etc.
9. & , The product should be situated away from heat sources such as radiators, heat registers, stoves, or other products (including amplifiers) that produce heat.
10.  , Keep the product away from open flame sources.
11. ")$"'$%, The product should be connected to a power supply only of the type described in the operating instructions or as marked on the product.
12. $"'!!"$ "$+&"!, This product may be equipped with a polarized alternating-current line plug (a plug having one blade wider than the other). (A grounding type plug has two blades and a third grounding prong.) This plug will fit into the power outlet only one way. This is a safety feature. If you are unable to insert the plug fully into the outlet, try reversing the plug. If the plug should still fail to fit, contact your electrician to replace your obsolete outlet. Do not defeat the safety purpose of the polarized plug.
13. ")$"$$"&&"!, Power-supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords at plugs, convenience receptacles, and the point at which they exit from the product.
14. !!, The product should be cleaned only as recommended by the manufacturer.
15. "!'%$"%, The power cord of the product should be unplugged from the outlet when left unused for a long period of time.
16. &!#'!&$*, Care should be taken so that objects do not fall and liquids are not spilled onto the enclosure.
17.  #'$!$(, The product should be serviced by qualified service personnel when: a. The power-supply cord or plug has been damaged. b. Objects have fallen or liquid has been spilled into the product. c. The product has been exposed to rain or moisture. d. The product does not appear to operate normally or exhibits a marked change in performance. e. The product has been dropped or damaged.
18. $(!, The user should not attempt to service the product beyond what is described in the operating instructions. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as a power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.
19. &!!, For added protection for the product during a lightning storm or when it is left unattended and unused for long periods of time, unplug it from the wall outlet.
20. ($"!, Do not overload wall outlets, extension cords or integral convenience receptacles as this can result in a risk of fire or electric shock.
21. && !&%, Only use attachments and accessories specified by the manufacturer.
22. "&, Insure that the subwoofer is only connected to the rated source voltage. Do not connect the 120-volt version to 230-volts or vice-versa. This will result in damage to the subwoofer and possible injury to the user.
23.  &%, This product can be used in tropical or moderate climates.
To prevent electrical shock, match wide blade of plug to wide slot, fully inserted.
To reduce the risk of fire or electrical shock, do not expose this product to rain or moisture.
w w w . v e l o d y n e . c o m
SC -600D A mplifi e r User ’s Man ual
Ta b l e o f C o n t e n t s
Congratulations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
Product Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
SC-600D Subwoofer Amplifier . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
SC-600 IW, SC-600 IF/IC Subwoofers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
Setup Checklist . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
Front Panel Controls and Displays . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
Rear Panel Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
Rear Panel Connections - Detailed Explanation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
About Low-Pass Crossovers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
A Word About Your Home Theater Receiver’s Crossover and the
SC-600D Amplifier’s Crossover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
A Word About Interconnect Cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
A Word About Subwoofer Placement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
Selecting the Subwoofer to be Controlled . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
Usage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
Restore Defaults . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
Care of Your Amplifier and Subwoofer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
Troubleshooting and Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
Appendix A: RS-232 Serial Overview and Commands . . . . . . . . . . . . . . . . . . . . . . . . .17
Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19
w w w . v e l o d y n e . c o m
SC - 600D A mpli f ier Use r’s M a nual
ii
C o n g r a t u l a t i o n s
Congratulations on your purchase of a Velodyne (SC) SubContractor Series 600D amplifier and subwoofer. This system represents the state-of-the-art in low frequency reproduction. Read and follow the instructions below to ensure safe and proper system operation.
Warning!
To prevent fire or shock hazard, do not expose this equipment to rain or moisture. To avoid electrical shock, do not open the speaker enclosure or the amp chassis cover. Please observe all warnings on the equipment itself. There are no user serviceable parts inside. Please refer all service questions to your authorized Velodyne dealer.
P r i o r t o In s t a l l a t i o n
Please unpack the system carefully. Please save the carton and all packaging materials for future use. Record the serial number in the space provided on the warranty card and page 20 of this manual for future reference.
P r o d u c t F e a t u r e s
S C - 6 0 0 D S U B W O O F E R A M P L I F I ER
• 400 watts dynamic/200 watts RMS high efficiency, Class D
• DSP-controlled
• Four selectable presets for customized listening mode
• Automatic 5-band room equalizer (microphone included)
• Night-mode setting
• Mute control
• Line-level (RCA) inputs and outputs
• Speaker-level inputs with 5 way binding post connections
• Signal sensing auto turn on/off (defeatable)
• Variable volume control
• Selectable phase control (0, 90, 180 or 270 degrees)
• Built-in adjustable (30-160 Hz) digital low-pass crossover with 24 dB/octave slope
• Driver Displacement Control software to prevent over excursion and amp clipping
• Blue power indicator LED
• RS-232 Serial Interface
• 12 Volt trigger
• Universal IR repeater mini-jack
• Preset-specific subsonic filter
w w w . v e l o d y n e . c o m
SC - 600D A mpli f ier Use r’s M a nual
1
S C - 6 0 0 I W, S C -6 0 0 IF / I C S U B W O O F E R S
SC-600 IW (In-Wall):
- Two high excursion 6.5” active drivers, two 12.5” x 3” oval passive radiators with ribbed rubber surround
- High-excursion rubber surrounds on both active and passive drivers
- 2” 4 layer copper
- Frequency Response: 30 - 120Hz (+/- 3 dB)
- 4 ohm impedance
SC-600 IF/IC (In-Floor/In-Ceiling):
- 12” (9.7” piston diameter) subwoofer
- 2.5” 4 layer copper
- Oversized spider for linearity at high excursion
- High-excursion rubber surround
- Frequency Response: 25 - 120Hz (+/- 3 dB)
- 4 ohm impedance
Note: The SC-600 IW and the SC-600 IF/IC must be driven with either the SC-600D or the SC-602 amplifier. Use of any other power source voids the warranty.
S e t u p C h e c k l i s t
Be sure to do the following to ensure the best performance from your subwoofer:
If possible, optimize the placement of the subwoofer(s) in the listening area.
See page 10 of the User’s Manual.
Install and wire the subwoofer per the instructions on pages 3 - 8.Select the proper model per the instructions on page 10.Select the proper volume level. See page 4.Be sure the low pass crossover is set correctly. See pages 8 - 9.Be sure to equalize the subwoofer using the microphone and Auto-EQ feature.
See page 11.
Be sure to set the phase control on the remote. See page 11.Select the correct preset for the source material. See page 13.
Your new Velodyne subwoofer system provides for a number of installation options. Read all the installation information below in order to determine which installation option is best for your system. Remember to perform all installation procedures with system power turned off.
Note: For proper setup and installation of the SC-600 IW (In-Wall) subwoofer, please refer to the SC-600 IW Quick Install Guide.
w w w . v e l o d y n e . c o m
SC - 600D A mpli f ier Use r’s M a nual
2
I n s ta l l a t i o n
F R O N T P A NE L C ON T R O L S A N D D I S P L AY S
F R O N T P A NE L C ON T R O L S A N D D I S P L AY S
Figure 1: Front Panel Connections of the SC-600D amplifier.
Following are brief descriptions of the controls described in Figure 1. More detail on these controls can be found in the next section.
(1) Power Switch
This button forces your SC-600D amplifier into standby mode. The power LED turns amber, the numeric LED shuts off, and the amplifier puts out no power. The unit will remain in this mode until the POWER button is pressed again. To fully deactivate (i.e. power down) the unit, use the main power switch on the back panel.
(2) Power LED
This LED illuminates when the power is on. Blue indicates normal operation. The LED turns amber when the unit is in standby mode or the remote has been used to deactivate the unit, and dims when the unit is in night mode.
(3) Mic Input
Connect the supplied microphone for the Auto-EQ feature to this mini-jack input.
(4) Remote Eye
This is the eye that receives infrared commands from the supplied remote.
(5) Crossover
Use these Up and Down buttons to select the frequency below which all signals will be routed to the subwoofer (for example, 80 Hz), rather that to the main speakers. The frequency is indicated on the LED display, then the display reverts to showing the subwoofer’s volume level. The slope is fixed at 24 dB/octave. To deactivate the crossover, press BOTH the Up and Down crossover buttons at the same time – two dashes on the display indicate the crossover is deactivated and the woofer plays all frequencies presented to it. Please see page 8 for a more detailed discussion on crossovers.
w w w . v e l o d y n e . c o m
SC - 600D A mpli f ier Use r’s M a nual
3
(6) LED Numeric Indicator
This LED supplies information on volume, crossover, woofer type, and other information. The “light” button on the remote deactivates this display. Upon startup, the display shows the model of subwoofer the SC-600D amp is controlling, then reverts to the volume indicator.
(7) Volume Control
T
hese buttons allow you to balance the output from the subwoofer to the main speakers in your system. The volume should be set to achieve similar volume level of both the main speakers and subwoofer. The default volume is 30.
Note: Volume can also be controllable by using the supplied remote.
WARNING: Some manufacturers preset their receivers with the Sub-Out (a.k.a. LFE) channel signal at a minimum level. It is very important to verify that your receiver Sub-Out channel is set to the same output level as your front right and left channels. Refer to your receiver manual for the individual channel level adjustment procedure. If your receiver Sub­Out channel is set too low, the subwoofer may appear to have a weak output, it may sound noisy or distorted, and the Auto On/Off feature may not operate properly.
(8) Optional Rack Mount Ears (Included)
These ears can be attached to the SC-600D amp to allow standard 19” rack mounting.
R E A R PA N EL C O NN E C T I O N S
Following are brief descriptions described in Figure 2. More detail on these controls can be found in the next section.
N10533
Figure 2: Rear Panel Connections of the SC-600D amplifier.
(9) Thru Jacks
These RCA connectors are for passing along the same signal that goes into your subwoofer to a second “daisy-chained” system. The signal from these RCA connectors is the same as the input signal.
(10) Line Input / LFE Input
Connect these jacks to the LINE OUT preamp output, LFE output, or subwoofer output jacks of your receiver/processor. If using the LFE output from your receiver or processor, plug the single cable into the jack labeled LFE input or, for more signal, use a “Y” connector (optional) and feed the signal into both “R” and “L” inputs. Examples of these types of connections can be found in Figures 2A and 2B.
w w w . v e l o d y n e . c o m
SC - 600D A mpli f ier Use r’s M a nual
4
Loading...
+ 16 hidden pages