Velleman VDPL300MF User Manual [en, de, es, fr]

VDPL300MF

LED MOONFLOWER - DMX-CONTROLLED - 64 LEDs
LEDMOONFLOWER - DMX-GESTUURD - 64 LEDS
MOONFLOWER À LED - PILOTAGE DMX - 64 LED
MOONFLOWER CON LEDs - CONTROLADO POR LA MÚSICA - 64 LEDs
LED MOONFLOWER - DMX-GESTEUERT - 64 LEDs

USER MANUAL
GEBRUIKERSHANDLEIDING
NOTICE D’EMPLOI
MANUAL DEL USUARIO
BEDIENUNGSANLEITUNG

VDPL300MF_v2 HQPOWER

2

VDPL300MF – LED MOONFLOWER - DMX-CONTROLLED - 64 LEDs

1. Introduction

To all residents of the European Union
Important environmental information about this product

This symbol on the device or the package indicates that disposal of the device after its lifecycle could harm
the environment.
Do not dispose of the unit (or batteries) as unsorted municipal waste; it should be taken to a specialized

company for recycling.
This device should be returned to your distributor or to a local recycling service.
Respect the local environmental rules.

If in doubt, contact your local waste disposal authorities.

Thank you for choosing HQPOWER! Please read the manual thoroughly before bringing this device into service. If the
device was damaged in transit, don't install or use it and contact your dealer.

2. Safety Instructions

Be very careful during the installation: touching live wires can cause life-threatening electroshocks.

Keep this device away from rain and moisture.

Unplug the mains lead before opening the housing.

• Damage caused by disregard of certain guidelines in this manual is not covered by the warranty and the dealer

will not accept responsibility for any ensuing defects or problems.

• A qualified technician should install and service this device.

• Do not switch the device on immediately after it has been exposed to changes in temperature. Protect the device

against damage by leaving it switched off until it has reached room temperature.

• This device falls under protection class I. It is therefore essential that the device be earthed. Have a qualified

person carry out the electric connection.

• Make sure that the available voltage does not exceed the voltage stated in the specifications of this manual.

• Do not crimp the power cord and protect it against damage. Have an authorised dealer replace it if necessary.

• Disconnect the device from the mains to clean it or when it is not in use. Handle the power cord by the plug only.

• Do not look directly at the light source as sensitive people may go into epileptic seizure if they do.

• Note that damage caused by user modifications to the device is not covered by the warranty.

• Lamps and mechanical wear are not covered by warranty.

• Keep the device away from children and unauthorised users.

3. General Guidelines

• This device is designed for professional use on stage, in discos, theatres, etc. The VDPL300MF should only be

used indoors and connected to an alternating current of max. 230VAC/50Hz.

• Lighting effects are not designed for permanent operation: regular operation breaks will prolong their lives.

• Do not shake the device. Avoid brute force when installing or operating the device.

• Select a location where the device is protected against extreme heat, dust and moisture. Respect a minimum

distance of 0.5m between the device’s light output and any illuminated surface.

• Use an appropriate safety cable to fix the device (e.g. VDLSC7 or VDLSC8).

• Familiarise yourself with the functions of the device before actually using it. Do not allow operation by unqualified

people. Any damage that may occur will most probably be due to unprofessional use of the device.

• Use the original packaging if the device is to be transported.

VDPL300MF_v2 HQPOWER

3

• All modifications of the device are forbidden for safety reasons.

• Only use the device for its intended purpose. All other uses may lead to short circuits, burns, electroshocks,

crash, etc. Using the device in an unauthorised way will void the warranty.

4. Mounting the Device

• Have the device installed by a qualified person, respecting EN 60598-2-17 and all other applicable norms.

• The carrying construction must be able to support 10 times the weight of the device for 1 hour without deforming.

• The installation must always be secured with a secondary attachment e.g. a safety cable.

• Never stand directly below the device when it is being mounted, removed or serviced. Have a qualified technician

check the device once a year and once before you bring it into service.

• Install the device in a location with few passers-by that is inaccessible to unauthorised persons.

• Overhead mounting requires extensive experience: calculating workload limits, determining the installation

material to be used… Have the material and the device itself checked regularly. Do not attempt to install the
device yourself if you lack these qualifications as improper installation may result in injuries.

• Adjust the desired inclination angle via the mounting bracket and tighten the bracket screws.

• Make sure there is no flammable material within a 0.5m radius of the device.

• Have a qualified electrician carry out the electric connection.

• Connect the device to the mains with the power plug. Do not connect it to a dimming pack.

• The installation has to be approved by an expert before the device is taken into service.

5. Use

The VDPL300MF can be used as a stand-alone device or in a master/slave configuration.

• Master/Slave Mode

Connect all units through the XLR connections (male = input, female = output) using standard XLR cables. The first
unit in the chain should be the master device. Choose the desired mode on the master device and set all other

devices into slave mode (press MODE until SLAV is displayed).

• Program Mode

Select your pattern, speed and flash rate. Press MODE until PR.XX is displayed. Select one of the 15 programs with
UP/DOWN and confirm with SET UP. SP.XX is now displayed. Adjust the speed from 1 ~ 99 with UP/DOWN. Confirm
with SET UP. FS.XX is now displayed. Adjust the flash rate from 1 ~ 99 with UP/DOWN. Confirm with SET UP.

• Auto Mode

Press MODE until auto is displayed. The device will run through the 15 built-in programs.

• Sound-Controlled Mode

The device will react to the surrounding noises and chase through the different colours. Press MODE until SU.XX is
displayed. Press UP/DOWN and adjust the sound sensitivity between 01 ~ 10 (from low to high).

VDPL300MF_v2 HQPOWER

4

6. DMX Control

DMX control allows you to create your own programs tailored to your personal needs. Each DMX fixture can be
controlled using a DMX controller. Press MODE until D.XXX is displayed.

• Detailed DMX Values per Channel

Channel Function From To Description

1 Pattern selection 0 255 15 auto programs + sound activation
2 Speed 0 255 Speed from slow to fast
3 Strobe function 0 255 Strobe from slow to fast
4 Sound sensitivity 0 255 Sensitivity from low to high

• DMX512 Connection

Connect the provided XLR cable to the female 3-pin XLR output of your controller and the other side to the male 3­pin XLR input of the VDPL300MF. Multiple VDPL300MFs can be linked through serial linking. The linking cable
should be a two-core screened cable with XLR input and output connectors.

• DMX512 Chain with Termination

A DMX terminator is recommended for installations where the DMX cable has to run a
long distance or is in an electrically noisy environment (e.g. discos). The terminator
prevents corruption of the digital control signal by electrical noise. The DMX terminator is
simply an XLR plug with a 120Ω resistor between pins 2 and 3, which is then plugged into
the XLR output socket of the last device in the chain.
Please see illustrations.

• DMX Start Address Selection

All DMX-controlled devices need a digital start address so that the correct device responds to the signals. This start
address is the channel number from which the device starts to “listen” to the DMX controller. Enter the correct
number and read it from the display located on the base of the VDPL300MF.
You can use the same starting address for a whole group of devices or enter an individual one for every device.
When all devices have the same address, all the VDPL300MFs will “listen” to the control signal on one particular
channel. In other words: changing the settings of one channel will affect all devices simultaneously. If you set
different addresses, each device will “listen” to a separate channel number. Changing the settings of one channel will
only affect the device in question.
In the case of the 4-channel VDPL300MF, you will have to set the start address of the first VDPL300MF to 1, the
second VDPL300MF to 5 (1 + 4), the third to 9 (5 + 4) and so on.

7. Cleaning and Maintenance

1. All screws should be tightened and free of corrosion.

2. The housing, visible parts, mounting supports and the installation location (e.g. ceiling, suspension, trussing)

should not be deformed, modified or tampered with e.g. do not drill extra holes in mounting supports, do not
change the location of the connections.

3. Moving mechanic parts must not show any signs of wear and tear.

4. The electric power supply cables must not show any damage. Have a qualified technician maintain the device.

5. Disconnect the device from the mains prior to maintenance activities.

6. Wipe the device regularly with a moist, lint-free cloth. Do not use alcohol or solvents.

7. There are no user-serviceable parts.

8. Contact your dealer for spare parts if necessary.

VDPL300MF_v2 HQPOWER

5

8. Technical Specifications

Power Supply max. 230VAC/50Hz
Power Consumption 20W
Fuse 1A, 250VAC (5 x 20mm) (order code FF1N)
Flash Rate 18Hz
LEDs 64 pcs (32 x red, 20 x green, 12 x blue)
Dimensions 195 x 256 x 125mm
Total Weight 2.4kg
Max. Ambient Temperature 45°C
Max. Housing Temperature 130°C

Use this device with original accessories only. Velleman nv cannot be held responsible in the event of
damage or injury resulted from (incorrect) use of this device.

For more info concerning this product, please visit our website www.hqpower.com.
The information in this manual is subject to change without prior notice.

VDPL300MF – LEDMOONFLOWER - DMX-GESTUURD - 64 LEDS

1. Inleiding

Aan alle ingezetenen van de Europese Unie
Belangrijke milieu-informatie betreffende dit product

Dit symbool op het toestel of de verpakking geeft aan dat, als het na zijn levenscyclus wordt weggeworpen,
dit toestel schade kan toebrengen aan het milieu.
Gooi dit toestel (en eventuele batterijen) niet bij het gewone huishoudelijke afval; het moet bij een

gespecialiseerd bedrijf terechtkomen voor recyclage.
U moet dit toestel naar uw verdeler of naar een lokaal recyclagepunt brengen.
Respecteer de plaatselijke milieuwetgeving.

Hebt u vragen, contacteer dan de plaatselijke autoriteiten inzake verwijdering.

Dank u voor uw aankoop! Lees deze handleiding grondig voor u het toestel in gebruik neemt. Werd het toestel
beschadigd tijdens het transport, installeer het dan niet en raadpleeg uw dealer.

2. Veiligheidsinstructies

Wees voorzichtig bij de installatie: raak geen kabels aan die onder stroom staan om dodelijke elektroshocks
te vermijden.

Bescherm dit toestel tegen regen en vochtigheid.

Verzeker u ervan dat het toestel niet aangesloten is op een stroombron alvorens het te openen.

• De garantie geldt niet voor schade door het negeren van bepaalde richtlijnen in deze handleiding en uw dealer zal

de verantwoordelijkheid afwijzen voor defecten of problemen die hier rechtstreeks verband mee houden.

• Laat dit toestel installeren en onderhouden door een geschoolde technicus.

• Om beschadiging te vermijden, zet u het toestel best niet aan onmiddellijk nadat het werd blootgesteld aan

temperatuurschommelingen. Wacht tot het toestel op kamertemperatuur gekomen is.

• Dit toestel valt onder beschermingsklasse I, wat wil zeggen dat het toestel geaard moet zijn. Een geschoolde

technicus moet de elektrische aansluiting verzorgen.

• De beschikbare netspanning mag niet hoger zijn dan de spanning in de specificaties achteraan de handleiding.

• De voedingskabel mag niet omgeplooid of beschadigd zijn. Laat uw dealer zo nodig een nieuwe kabel plaatsen.

• Trek de stekker uit het stopcontact (trek niet aan de kabel!) voordat u het toestel reinigt en als u het niet gebruikt.

VDPL300MF_v2 HQPOWER

6