Velleman VDPDP134 User Manual [en, de, es, fr]

USER MANUAL

VDPDP134

6-CHANNEL DMX DIMMER PACK
6-KANAALS DMX DIMMERPACK
UNITÉ DE PUISSANCE 6 CANAUX
DIMMER PACK DMX DE 6 CANALES
6-KANAL-DMX-DIMMER PACK (6 x 10A)

GEBRUIKERSHANDLEIDING
NOTICE D’EMPLOI
MANUAL DEL USUARIO
BEDIENUNGSANLEITUNG

2

VDPDP134 VELLEMAN

3

VDPDP134 – 6-CHANNEL DIMMER PACK

1. Introduction & Features

To all residents of the European Union
Important environmental information about this product

This symbol on the device or the package indicates that disposal of the device after its lifecycle could harm
the environment.
Do not dispose of the unit (or batteries) as unsorted municipal waste; it should be taken to a specialised

company for recycling.
This device should be returned to your distributor or to a local recycling service.
Respect the local environmental rules.

If in doubt, contact your local waste disposal authorities.

Thank you for buying the VDPDP134! Please read the manual carefully before bringing this device into service.
This powerful and versatile device features 6 channels with LED indication. The device is controlled through DMX or
an analogue input and is equipped with a preheating function and a two-phase power output.
Check carefully for damage caused by transportation. Consult your dealer and don’t install this device if it has been
damaged in transit.

2. Safety Instructions

Be very careful during the installation: touching live wires can cause life-threatening electroshocks.

Keep this device away from rain and moisture.
Unplug the mains lead before opening the housing.

• A qualified technician should install and service this device.

• Damage caused by disregarding certain guidelines in this manual is not covered by the warranty and the dealer

will not accept responsibility for the ensuing defects or problems.

• Do not switch the device on immediately if it has been exposed to changes in temperature. Protect the device

against damage by leaving it switched off until it has reached room temperature.

• This device falls under protection class I. It is essential, therefore, that the device be earthed. Have this device

installed by a qualified technician.

• Make sure that the available voltage does not exceed the voltage stated in the specifications of this manual.

• Do not crimp the power cord and protect it against damage from sharp edges. Ask an authorised dealer to replace

the cord if necessary.

• Always disconnect the device from the mains when it is not in use or when you wish to clean it. Only handle the

power cord by the plug. Never pull out the plug by tugging the power cord.

• Note that damage caused by user modifications to the device are not covered by the warranty. Keep the device

away from children and unauthorised users.

3. General Guidelines

• This device is a lighting controller for professional use on stage, in discos, theatres, etc. The VDPDMXDP134

should only be used indoors with an alternating current of max. 230Vac/50Hz.

• Do not shake the device. Avoid brute force when installing or operating the device.

• Select a location where the device will be protected against extreme heat, moisture and dust.

• Do not use or transport the device under temperatures < 5°C or > 35°C.

• Familiarise yourself with the functions of the device before actually using it. Do not permit operation by unqualified

people. Any damage that may occur will probably be due to unprofessional use of the device.

• Use the original packaging if the device is to be transported.

VDPDP134 VELLEMAN

4

• Note that all modifications of the device are forbidden for safety reasons.

• Do not remove the serial number sticker from the device as doing so will void the warranty. Only use the device

for its intended purpose. All other uses may cause short circuits, burns, electroshocks, lamp explosions, crashes,
etc. Using the device in an unauthorised way will void the warranty.

4. Description

a) Front Panel

1. Automatic circuit breakers 20A

2. Preheating adjustment (max. 50%)

3. Power ON indicator

4. DMX channel output indicators

5. DMX "ON" indicator

6. Power switch

7. DMX channel output faders : adjusts the output level (dimming level) of each channel

8. DMX start address, selected via DIP switch settings

9. Load indicators

b) Back Panel

10. Analogue input (0-10Vdc)

11. Analogue output

12. DMX input (3-pin male XLR)

13. DMX output (3-pin female XLR)

14. Schuko sockets

15. Power input

c) Connections

Remove the cover of the load connection box and connect the mains and the load to the device according to the
figure above.

VDPDP134 VELLEMAN

5

5. Operating Instructions

Manual Control : Manual control is possible through the channel faders if neither an analogue or DMX controller

are used. Slide them up or down to adjust the output (dimming level) for each channel.

Preheating : Enables you to adjust the min. output level (between 0-50%), which enhances the life of the

lamps.

Analogue Input : Connect the analogue controller according to the diagram below. The device supplies the

controller with DC power.

DMX Input : The dimmer pack can receive DMX512 signals. Adjust the DIP switches to confirm the start

address of the device. When the 10th switch is placed in the ON-position and you move one of
the sliders, then all channels will react simultaneously and they will all be placed at the same
level.

Setting the DMX Start Address :

VDPDP134 VELLEMAN

6

6. Cleaning and Maintenance

W

ees voorzichtig bij de installatie: raak geen kabels aan die onder stroom staan om

dodelijke elektroshocks

1. All screws for installing the devices or parts of the device have to be screwed down tight and must not be

corroded.

2. The housing, mounting supports and connections should not be modified or tampered with e.g. do not drill extra

holes in mounting supports, do not change the location of the connections, etc.

3. The electric power supply cables must be undamaged. Have the device installed by a qualified technician.

4. Disconnect the device from the mains prior to maintenance activities.

5. Wipe the device regularly with a moist cloth. Do not use alcohol or solvents.

6. Entrust a qualified technician with the maintenance of this device. Contact your dealer for spare parts if

necessary.

7. Technical Specifications

Max. Power Input 230Vac/50Hz, three-phase or single-phase, 60A
Number of Channels 6
Max. Total Load 20A per phase
Max. Total Current max. 10A per channel
Max. Load per Channel 2200W
Analogue Input & Output 8-pin DIN socket (0-10Vdc)
DMX Input & Output 3-pin XLR socket
Fuses automatic circuit breaker 20A
Dimensions 482 x 381 x 89mm
Weight 8.4kg

The information in this manual is subject to change without prior notice.

VDPDP134 – 6-KANAALS DIMMERPACK

1. Inleiding & Kenmerken

Aan alle ingezetenen van de Europese Unie
Belangrijke milieu-informatie betreffende dit product

Dit symbool op het toestel of de verpakking geeft aan dat, als het na zijn levenscyclus wordt weggeworpen,
dit toestel schade kan toebrengen aan het milieu.
Gooi dit toestel (en eventuele batterijen) niet bij het gewone huishoudelijke afval; het moet bij een

gespecialiseerd bedrijf terechtkomen voor recyclage.
U moet dit toestel naar uw verdeler of naar een lokaal recyclagepunt brengen.
Respecteer de plaatselijke milieuwetgeving.

Hebt u vragen, contacteer dan de plaatselijke autoriteiten inzake verwijdering.

Dank u voor uw aankoop! Lees de handleiding voor u het toestel in gebruik neemt. Dit krachtige en veelzijdige
toestel beschikt over 6 kanalen met LED aanduiding. De sturing gebeurt via DMX of een analoge ingang. Het toestel
is uitgerust met een voorverwarmingsfunctie en een tweefazige vermogensuitgang. Ga na of het toestel werd
beschadigd tijdens het transport. Zo ja, stel dan de installatie van het toestel uit en raadpleeg uw dealer.

2. Veiligheidsinstructies

te vermijden.

Bescherm dit toestel tegen regen en vochtigheid.
Verzeker u ervan dat het toestel niet aangesloten is op een stroombron alvorens het te openen.

VDPDP134 VELLEMAN