Velleman VDLPROM1 User Manual [en, de, es, fr]

USER MANUAL

VDLPROM1

DISCO LIGHT SET

GEBRUIKERSHANDLEIDING NOTICE D’EMPLOI MANUAL DEL USUARIO BEDIENUNGSANLEITUNG

VDLPROM1_v2 VELLEMAN

VDLPROM1 – DISCO LIGHT SET

1. Introduction & Features

To all residents of the European Union Important environmental information about this product

This symbol on the device or the package indicates that disposal of the device after its lifecycle could harm the environment.

Do not dispose of the unit (or batteries) as unsorted municipal waste; it should be taken to a specialized company for recycling. This device should be returned to your distributor or to a local recycling service. Respect the local environmental rules.

If in doubt, contact your local waste disposal authorities.

Thank you for buying the VDLPROM1! Please read the manual thoroughly before bringing this device into service. Make sure that the device was not damaged in transit. If the device is damaged, you should contact your dealer and postpone installation of this device. Verify if the set is complete: a mirror ball with attachment ring, a chain with key ring, a mirror ball motor, a PAR-36 pin spot with mounting bracket, a PAR-36 lamp, a colour wheel and a colour wheel motor.

2. Safety Instructions

Be very careful during the installation: touching live wires can cause life-threatening electroshocks.

Do not touch the device during operation as the housing heats up.

Keep this device away from rain and moisture.

Unplug the mains lead before opening the housing.

• Damage caused by disregard of certain guidelines in this manual is not covered by the warranty and the dealer

will not accept responsibility for any ensuing defects or problems.

• A qualified technician should install and service this device.

• Do not switch the device on immediately after it has been exposed to changes in temperature. Protect the device

against damage by leaving it switched off until it has reached room temperature.

• This device falls under protection class I. It is therefore essential that the device be earthed. The power plug must

only be plugged into a protection class I outlet. Have a qualified person carry out the electric connection.

• Make sure that the available voltage does not exceed the voltage stated in the specifications of this manual.

• Do not crimp the power cord and protect it against damage. Have an authorised dealer replace it if necessary.

• Disconnect the device from the mains to clean it or when it is not in use. Handle the power cord by the plug only.

• There may be some smoke or a particular smell when the device is activated for the first time. This is normal and

any smoke or smell will gradually disappear.

• Do not look directly at the light source as sensitive people may go into epileptic seizure if they do.

• Replace the shields, lenses or UV screens if they have become visibly damaged (e.g. cracks, deep scratches) to

such an extent that their effectiveness is impaired.

• Replace the lamp if it has become damaged or thermally deformed.

• Note that damage caused by user modifications to the device are not covered by the warranty.

• Keep the device away from children and unauthorised users.

VDLPROM1_v2 VELLEMAN

3. General Guidelines

• This set includes a mirror ball and pin spot for use at home, on stages, in discotheques, in theatres etc.

• The VDLPROM1 should only be used indoors with an alternating current of 230V AC/50Hz.

• Lighting effects are not designed for permanent operation: regular operation breaks will prolong their lives.

• Do not shake the device. Avoid brute force when installing or operating the device.

• Select a location where the device is protected against extreme heat (see “7. Technical Specifications”), dust and

moisture. Respect a minimum distance of 0.5m between the device’s light output and any illuminated surface.

• Use an appropriate safety cable to fix the device (e.g. VDLSC7 or VDLSC8).

• Familiarise yourself with the functions of the device before actually using it. Do not allow operation by unqualified

people. Any damage that may occur will most probably be due to unprofessional use of the device.

• Use the original packaging if the device is to be transported.

• All modifications of the device are forbidden for safety reasons.

• Only use the device for its intended purpose. All other uses may lead to short circuits, burns, electroshocks, lamp

explosion, crash, etc. Using the device in an unauthorised way will void the warranty.

4. Installation

a) Lamps

• Only fit or replace a lamp when the device is unplugged from the mains.

• Only operate the device with a fastened lamp.

• Let a lamp cool down before replacing it as the temperature of a lamp can reach 150°C during operation.

• Do not install lamps with a higher wattage. They get hotter than this device was designed for.

• Replace any deformed or damaged lamp with a lamp of the same type (see “7. Technical Specifications”):

1. Unscrew the front ring, holding the lamp into place.

2. Remove the old lamp and unscrew the wires from it.

3. Fasten the wires to the new lamp, put it in the housing and fix it by fastening the fixation ring.

b) Colour Wheel

1. Carefully unpack the colour wheel and remove the protective film.

2. Fix the colour wheel to the axe of the motor by means of the screw provided.

c) The Pin Spot

• Have the device installed by a qualified person, respecting EN 60598-2-17 and all other applicable norms.

• The construction to which the pin spot is attached should be able to support 10 times the weight of the device for

one hour without deformation.

• The installation must always be secured with a secondary attachment e.g. a safety cable.

• Never stand directly below the device when it is being mounted, removed or serviced. Have a qualified technician

check the device once a year and once before you bring it into service.

• Install the device in a location with few passers-by that is inaccessible to unauthorised persons.

• Overhead mounting requires extensive experience: calculating work load limits, determining the installation

material to be used… Have the material and the device itself checked regularly. Do not attempt to install the device yourself if you lack these qualifications as improper installation may result in injuries.

• Adjust the desired inclination angle via the mounting bracket and tighten the bracket screws.

• Make sure there is no flammable material within a 50cm radius of the device.

• Have a qualified electrician carry out the electric connection.

• Connect the device to the mains with the power plug. Don’t connect it to a dimming pack.

• The installation has to be approved by an expert before the device is taken into service.

VDLPROM1_v2 VELLEMAN

d) The Mirror Ball and Motor

• The construction to which the mirror ball is attached should be able to support 10 times the weight of the device

for one hour without deformation. It should be able to hold a minimum of 10kg point load.

• The installation must always be secured with a secondary attachment e.g. a safety net.

• Never stand directly below the device when it is being mounted, removed or serviced. Have a qualified technician

check the device once a year and once before you bring it into service.

• Install the device in a location with few passers-by that is inaccessible to unauthorised persons.

• Overhead mounting requires extensive experience: calculating work load limits, determining the installation

• The mirror ball has to be connected to the motor via the chain. Make sure the motor is installed perfectly

horizontally. There are 3 holes in the base plate for fixation screws.

• Make sure the rotation of the mirror ball is never hampered and that no side forces can impact on the installation.

• The installation has to be approved by an expert before the device is taken into service.

5. Use

After connecting the devices to the mains, the mirror ball motor will rotate at 3 RPM, the lamp will be on and the colour wheel will be turning. By aiming the spot towards the mirror ball, you will obtain a beautiful, colourful effect.

6. Cleaning and Maintenance

1. All screws should be tightened and free of corrosion.

2. The housing, the lenses, the mounting supports and the installation location should not be deformed, modified or

tampered with e.g. do not drill extra holes in mounting supports, do not change the location of the connections, …

3. Mechanically moving parts must not show any signs of wear and tear.

4. The electric power supply cables must not show any damage. Have a qualified technician maintain the device.

5. Disconnect the device from the mains prior to maintenance activities.

6. Wipe the device regularly with a moist, lint-free cloth. Do not use alcohol or solvents.

7. There are no user-serviceable parts, apart from the lamp and the colour wheel (see “4. Installation”).

8. Contact your dealer for spare parts if necessary.

9. Check regularly if the key ring or chain shackles have been deformed. If so, demount the mirror ball immediately.

7. Technical Specifications

PAR-36 Pin Spot

Power Supply 230VAC/50Hz Power Consumption max. 30W Dimensions ∅ 120 x 160mm Weight 1,1kg Lamp PAR-36 lamp [order code LAMP36, LAMP36GE (General Electric)] Max. Ambient Temperature 45°C Max. Housing Temperature 100°C

Mirror Ball

Diameter 20 cm (8") Total Weight 0,9kg

VDLPROM1_v2 VELLEMAN

Mirror Ball Motor

Power Supply 230VAC/50Hz Power Consumption max. 4W Rotation Speed 3 RPM Dimensions ∅ 110 x 45mm Total Weight 0,22kg Maximum diameter of mirror ball 30cm (12") Maximum load 3kg

Colour Wheel with Motor

Power Supply 230VAC/50Hz Rotation Speed 4 RPM Dimensions ∅ 130mm Colours red, yellow, blue, purple, green

For more info concerning this product, please visit our website www.hqpower.com. The information in this manual is subject to change without prior notice.

VDLPROM1 – DISCO LIGHT SET

1. Inleiding en kenmerken

Aan alle ingezetenen van de Europese Unie Belangrijke milieu-informatie betreffende dit product

Dit symbool op het toestel of de verpakking geeft aan dat, als het na zijn levenscyclus wordt weggeworpen, dit toestel schade kan toebrengen aan het milieu.

Gooi dit toestel (en eventuele batterijen) niet bij het gewone huishoudelijke afval; het moet bij een gespecialiseerd bedrijf terechtkomen voor recyclage. U moet dit toestel naar uw verdeler of naar een lokaal recyclagepunt brengen. Respecteer de plaatselijke milieuwetgeving.

Hebt u vragen, contacteer dan de plaatselijke autoriteiten inzake verwijdering.

Dank u voor uw aankoop! Lees deze handleiding grondig voor u het toestel in gebruik neemt. Ga na of het toestel niet werd beschadigd tijdens het transport. Zo ja, stel dan de installatie van het toestel uit en raadpleeg uw dealer. Controleer of de set volledig is: een spiegelbol met bevestigingsring, een ketting met bevestingsschakel, een motor voor de spiegelbol, een PAR-36 puntspot met bevestigingsbeugel, een PAR-36 lamp, een kleurenschijf en een motor daarvoor.

2. Veiligheidsinstructies

Wees voorzichtig bij de installatie: raak geen kabels aan die onder stroom staan om dodelijke elektroshocks te vermijden.

Raak het toestel niet aan wanneer het in gebruik is: de behuizing wordt warm.

Bescherm dit toestel tegen regen en vochtigheid.

Ontkoppel de voedingskabel en open dan pas de behuizing.

• De garantie geldt niet voor schade door het negeren van bepaalde richtlijnen in deze handleiding en uw dealer zal

de verantwoordelijkheid afwijzen voor defecten of problemen die hier rechtstreeks verband mee houden.

• Laat een geschoolde technicus dit toestel installeren en onderhouden.

• Om beschadiging te vermijden, mag u het toestel niet inschakelen onmiddellijk nadat het werd blootgesteld aan

temperatuurschommelingen. Wacht tot het toestel op kamertemperatuur gekomen is.

VDLPROM1_v2 VELLEMAN

+ 14 hidden pages