Velleman VDLL300MF User Manual [en, de, es, fr]

USER MANUAL

VDLL300MF

LED MOONFLOWER LED MOONFLOWER MOONFLOWER À LED MOONFLOWER CON LEDs LED MOONFLOWER

GEBRUIKERSHANDLEIDING NOTICE D’EMPLOI MANUAL DEL USUARIO BEDIENUNGSANLEITUNG

VDLL300MF_v2 VELLEMAN

VDLL300MF – LED MOONFLOWER

1. Introduction & Features

To all residents of the European Union Important environmental information about this product

This symbol on the device or the package indicates that disposal of the device after its lifecycle could harm the environment. Do not dispose of the unit (or batteries) as unsorted municipal waste; it should be taken to a specialized

company for recycling. This device should be returned to your distributor or to a local recycling service. Respect the local environmental rules.

If in doubt, contact your local waste disposal authorities.

Thank you for buying the VDLL300MF! This is a LED moonflower effect with sound activation mode. Please read the manual thoroughly before bringing this device into service. If the device was damaged in transit, don't install or use it and contact your dealer.

2. Safety Instructions

Be very careful during the installation: touching live wires can cause life-threatening electroshocks.

Keep this device away from rain and moisture. Unplug the mains lead before opening the housing.

• Damage caused by disregard of certain guidelines in this manual is not covered by the warranty and the dealer

will not accept responsibility for any ensuing defects or problems.

• A qualified technician should install and service this device.

• Do not switch the device on immediately after it has been exposed to changes in temperature. Protect the device

against damage by leaving it switched off until it has reached room temperature.

• This device falls under protection class I. It is therefore essential that the device be earthed. Have a qualified

person carry out the electric connection.

• Make sure that the available voltage does not exceed the voltage stated in the specifications of this manual.

• Do not crimp the power cord and protect it against damage. Have an authorised dealer replace it if necessary.

• Disconnect the device from the mains to clean it or when it is not in use. Handle the power cord by the plug only.

• Do not look directly at the light source as sensitive people may go into epileptic seizure if they do.

• Note that damage caused by user modifications to the device is not covered by the warranty.

• Keep the device away from children and unauthorised users.

3. General Guidelines

• This device is designed for professional use on stage, in discos, theatres, etc. The VDLL300MF should only be

used indoors with an alternating current of max. 230VAC / 50Hz.

• Lighting effects are not designed for permanent operation: regular operation breaks will prolong their lives.

• Do not shake the device. Avoid brute force when installing or operating the device.

• Select a location where the device is protected against extreme heat, dust and moisture. Respect a minimum

distance of 0.5m between the device’s light output and any illuminated surface.

• Use an appropriate safety cable to fix the device (e.g. VDLSC7 or VDLSC8).

• Familiarise yourself with the functions of the device before actually using it. Do not allow operation by unqualified

people. Any damage that may occur will most probably be due to unprofessional use of the device.

• Use the original packaging if the device is to be transported.

VDLL300MF_v2 VELLEMAN

• All modifications of the device are forbidden for safety reasons.

• Only use the device for its intended purpose. All other uses may lead to short circuits, burns, electroshocks,

crash, etc. Using the device in an unauthorised way will void the warranty.

4. Installation – mounting the device

• Have the device installed by a qualified person, respecting EN 60598-2-17 and all other applicable norms.

• The construction to which the device is attached should be able to support 10 times the weight of the device for

one hour without deformation.

• The installation must always be secured with a secondary attachment e.g. a safety cable.

• Never stand directly below the device when it is being mounted, removed or serviced. Have a qualified technician

check the device once a year and once before you bring it into service.

• Install the device in a location with few passers-by that is inaccessible to unauthorised persons.

• Overhead mounting requires extensive experience: calculating workload limits, determining the installation

material to be used… Have the material and the device itself checked regularly. Do not attempt to install the device yourself if you lack these qualifications as improper installation may result in injuries.

• Adjust the desired inclination angle via the mounting bracket and tighten the bracket screws.

• Make sure there is no flammable material within a 0.5m radius of the device.

• Have a qualified electrician carry out the electric connection.

• Connect the device to the mains with the power plug. Don’t connect it to a dimming pack.

• The installation has to be approved by an expert before the device is taken into service.

5. Use

• Connect the unit to the mains.

• Set the power switch to 1 to start the unit. The light beams will be controlled by the sound received by the

microphone on the back-side.

• Adjust the sound sensitivity through the speed button on the back-side of the unit.

• To turn off the unit, set the power switch to 0 and disconnect the unit from the mains when it is not in use.

6. Cleaning and Maintenance

1. All screws should be tightened and free of corrosion.

2. The housing, the lenses, the mounting supports and the installation location (e.g. ceiling, suspension, trussing)

should not be deformed, modified or tampered with e.g. do not drill extra holes in mounting supports, do not change the location of the connections…

3. Mechanically moving parts must not show any signs of wear and tear.

4. The electric power supply cables must not show any damage. Have a qualified technician maintain the device.

5. Disconnect the device from the mains prior to maintenance activities.

6. Wipe the device regularly with a moist, lint-free cloth. Do not use alcohol or solvents.

7. There are no user-serviceable parts.

8. Contact your dealer for spare parts if necessary.

7. Technical Specifications

Power Supply max. 230VAC / 50Hz LED 18 pcs (6 x red, 6 x green, 6 x blue) Dimensions 195 x 200 x 175mm Total Weight 2kg

For more info concerning this product, please visit our website www.hqpower.com. The information in this manual is subject to change without prior notice.

VDLL300MF_v2 VELLEMAN

+ 8 hidden pages