Velleman KSR9 User Manual [en, de, es, fr]

KSR9 – “BOTBALL” KIT

1. Introduction & Features

To all residents of the European Union
Important environmental information about this product

This symbol on the device or the package indicates that disposal of the device after its lifecycle could harm
the environment.
Do not dispose of the unit (or batteries) as unsorted municipal waste; it should be taken to a specialised

company for recycling.
This device should be returned to your distributor or to a local recycling service.
Respect the local environmental rules.

If in doubt, contact your local waste disposal authorities.

Thank you for buying the KSR9! Please read the manual thoroughly before bringing this device into service. If the
device was damaged in transit, don't install or use it and contact your dealer.

The KSR9 requires 2 x 1.5V AA batteries (not incl.) and 1 x 9V battery (not incl.); the remote control requires 4 x

1.5V AA batteries (not incl.). Apart from the batteries, you will also need a pair of long-nose pliers, a diagonal cutter
and a screwdriver.

2. Remote Control

a. Introduction

This is a 4-channel IR remote control used to control one KSR9. Line up to 4 KSR9’s by choosing a different channel
for each Botball.

b. Parts List

P1 Battery terminal #1 x 2 P2 Battery terminal #2 x 2 P3 Battery terminal #3 x 2

P4 Tapping screw (2.3 x 7mm) x 4 P6 Finished PCB

P5 Tapping screw (2.6 x 7mm) x 4

KSR9 - 1 - VELLEMAN

c. Assembly

3. The Botball

a. Introduction

Control the Botball by means of the remote control. Select a different channel for each Botball (max. 4 Botballs) when
playing against each other.

KSR9 - 2 - VELLEMAN

b. Parts List

P1-1 Motor x 2 P1-2 Motor x 1 P2 Motor holder x 2 P3 Face gear 36T/14T

(white) x 2

P4 Gear 36T/14T

(red) x 2

P5 Gear 36T/0T

(white) x 2

P6 Gear 48/18T

(white) x 3

P8 Pinion gear 8T

P9 Post x 1 P10 Hex post x 1 P11 Wheel x 2

(white) x 3

P12 Tyre x 2 P13 Round shaft (3 x

25mm) x 2

P14 Knurled shaft (2 x

13mm) x 1

P16 Washer x 2 P17 Round top nut x 2 P18 Machine screw (3 x

12mm) x 1

P20 Yellow Tube x 2 P21 Machine screw (3

x 6mm) x 1

P22 Tapping screw (2.3

x 12mm) x 3

P7 Pinion gear 10T (white)

x 1

P15 Round shaft (2 x

13mm) x 1

P19 Tapping screw (3 x

7mm) x 10

P23 Tapping screw (2.3 x

7mm) x 17

P24 Machine screw (2

P25 Sponge x 1 P26 Buzzer x 1 P27 Battery holder x 1

x 5mm) x 2

P28 Battery snap x 1 P30 Eyelet x 2 P31 Finished PCB

P29 Housing x 2

KSR9 - 3 - VELLEMAN

c. Assembly

KSR9 - 4 - VELLEMAN

KSR9 - 5 - VELLEMAN

Fig. 1

4. Dressing your Botball

Cut out the two shapes on the separate leaflet along the dotted lines, place them on a piece of cardboard and mark the
contours on the cardboard. Next, cut out the cardboard shapes and decorate the front and back of the shirt. Dress your
Botball according to the drawing below. Save the cut-out shapes in case you want to make other shirts.

KSR9 - 6 - VELLEMAN