Page 1
The Carbon Friendly Fan
Installation and Operating
Instructions
• 5 models:
- SAP Appendix Q Eligible
3 speed continuous running
with or without filter
- humidity control
- SELV - low voltage:
- 3 speed continuous
- humidity control
• for all domestic wet rooms
• for walls or ceilings
running
쓑
IPX4 IPX7
Page 2
"E-Smile” - THE POWERFUL CARBON FRIENDLY FANS
INSTALLATION and OPERATING INSTRUCTIONS
THIS LEAFLET MUST BE AVAILABLE TO THE USER
The product you have purchased is an extractor
fan for exhausting directly outside or through medium lengths of ducting and is suitable for wall or
ceiling installation. To ensure optimum operation
and guarantee a long life, please read this manual
carefully. It explains how to install correctly, use
and maintain the product properly. Following
these instructions will ensure the reliability of the
product and extend its working life.
The manufacturer will not be held responsible
and will not accept any responsibility for damage caused to persons or things due to
improper use with reference to the precautions
outlined in this leaflet.
The product, constructed using state of the art
technology, complies with current standards
regarding electrical equipment. It conforms with
the EMC 2014/30/EU European Directive regarding radio interference suppression and electromagnetic compatibility.
WARNING: Serious injury or death could result if
these instructions are not carefully followed
• Do not use this product for any purpose other
than that for which it was designed.
• Remove the product from its packaging and make
sure that it has not been damaged. If in doubt,
contact the supplier, authorised dealer, service
centre or manufacturer to check that the prod
uct will still operate correctly. Do not attempt
to use or repair the product before doing this.
• Do not leave packing material within the reach
of children or unskilled people. To dispose of
the packaging and the appliance at the end of its
useful life refer to the recycling norms in force.
• The use of any electrical product requires
compliance with some basic rules which are
listed below:
- do not touch it with wet or damp parts of the
body (e.g hands, feet).
- this appliance can be used by children aged
from 8 years and above and persons with
reduced physical, sensory or mental capabilities or lack of experience and knowledge if
they have been given supervision or instruc
tion concerning use of the appliance in a
safe way and understand the hazards involved. Children shall not play with the appli
ance. Cleaning and user maintenance shall
not be done by children without supervision.
• The product should be connected to the mains
electricity supply or electrical outlet only if:
- the electrical voltage and frequency corre-
spond to those shown on the rating label.
- the capacity of the electricity supply is suffi-
cient to operate the product at its maximum
power.
- suitable electrical protection must be provid-
ed for the product to be installed.
• The electrical supply to which the fan is connected must comply with all existing regulations. All installations must comply with current
IEE wiring regulations.
• Before maintenance or cleaning is carried out,
the product must be switched off and disconnected from the mains electricity supply.
• If a fault, malfunction or anomaly of any type
occurs, the fan should be isolated (switching it
off and disconnecting it from the mains electric
ity supply) and advice sought from qualified
personnel.
2
Page 3
• Always request original spare parts for repairs
• If the product needs to be removed, turn off the
mains supply circuit-breaker and then disconnect the fan.
• The fan MUST BE installed as detailed in
this leaflet
WARNING: Damage could be caused to the
product if the installation instructions are not
followed
• The product should not be used in an ambient
temperature higher than 40°C (104°F).
• The product should not be exposed to atmospheric agents (rain, sun, snow, etc.).
• The product or its parts should not be
placed in water or other liquids.
• Routine maintenance as described below
should be carried out to check the condition of
the fan.
• The air or fumes being extracted must be clean
and free from greasy particles, soot, chemical
and corrosive agents, flammable or explosive
mixtures.
• The product must be installed by profes-
sionally qualified personnel. Incorrect
installation can cause damage to people,
animals or property, for which the manufacturer cannot be held liable.
• The product must be connected to the electricity supply via a double pole switch of a suitable
size, with contact openings of at least 3 mm.
• If the electrical supply board (or switching
device) is located some distance from the fan a
means of local isolation must be provided.
• To ensure optimum operation, do not block the
air intake and exit vents.
• Any ducting used must be free of blockages.
• The room where the product is operating must
have adequate air replacement to ensure maximum effectiveness.
• If the product is sited in a room containing a
fuel burning appliance which is not of the balanced flue type, the installer must ensure that
air replacement is adequate both for the fan
and the fuel burning appliance.
• The product must not be used as an activator
for water heaters, stoves, etc.
• The product must not exhaust into ducts
designed to evacuate fumes from combustion
in stoves or other combustion-powered
devices.
RANGE
ES1003 - this fan combines the latest technology
with energy saving and efficiency. It is a quiet
running, 3 speed fan. It is designed to run
continuously at a pre-selectable choice of 2 lower
speeds (fixed at installation). The user can boost
the fan speed to its maximum performance when
required by means of the cord or remove the cord
and use a remote switch, light switch, PIR sensor
or humidistat. The ES1003 is SAP Appendix Q
Listed.
ES1003CF - as above, but complete with metal
filter.
ES100H2C - humidity control model - the fan will
start to operate automatically at its lower speed
when the relative humidity reaches the pre-set
level and will continue to operate at this speed
until the humidity has been dispersed. The user
can use the cord or the remote switch (if the cord
has been removed) to operate the fan (at its higher speed), or boost the fan speed if it is already
running. Pulling the cord again (or switching off)
will revert the fan to its lower speed, and it will
continue to run either until the humidity has been
removed, or the fan has completed the timer
over-run period (adjustable between 3 and 25
minutes). The fan's "comfortimer” technology
3
Page 4
allows the fan to run at low speed for its over-run
period. The humidistat is adjustable from 40% to
90% relatve humidity.
ES1003CLV - 12v SELV version of ES1003
ES100H2CLV - 12v SELV version of ES100H2C
INSTALLATION
4
Page 5
5
Page 6
ES1003 - JUMPER SWITCH - 230v models
INSTALLATION
Fig 1: check there is nothing missing in box
and that instruction leaflet is included
Fig 2: drill hole in wall - minimum dia 99.8mm
- allow extra width if using ducting -
it is the installer's responsibility to
use the appropriate core cutter to
obtain the correct hole diameter.
Fig 3: use fan assembly as template to mark
drill holes - NB fan can be at any angle
Fig 4: drill 3 x 6mm dia holes
Fig 5: fit wall plugs
Fig 6: decide whether to have cable access
from rear (recessed) or bottom (sur
face) of fan - if from bottom ensure that
included grommet is properly fixed
Fig 7: if cable is to come through rear of fan,
fit rubber ring (included)
Fig 8: gasket included for ceiling installation
Fig 9: screw fan to wall
Figs 10, ll: make electrical connection using
cable clamp
Figs A: Wiring diagrams follow. NB this fan is
double insulated and does not need
to be earthed
N.B This fan is NOT suitable for use with a
Gravity Grille. It should be installed using
either a Cowl or Fixed Grille.
Fig 12: Replace front cover
The ES1003 is designed to run continuously
at one of 2 lower speeds fixed at installation
using the jumper switch. Fan supplied
ready for Speed 1 - lower speed. Installer
can change to Speed 2 if required. The
user can boost the fan speed to its maximum performance by using cord or remote
switch (when installing with remote switch,
pullcord switch must be left in "off" position
and cord removed).
NOTE: SELV products have a 3 pin jumperswitch - see pages 8 and 9.
56
Page 7
WIRING DIAGRAMS
ES1003 - 3 Speed with Cord
ES1003CF - 3 Speed with Cord & Filter
ES100H2C - Humidity Control with Cord
VIA LIGHT SWITCH
ES1003 - 3 Speed with Cord removed
ES1003CF - 3 Speed with Filter - Cord removed
ES100H2C - Humidity Control - Cord removed
VIA REMOTE ILLUMINATED SWITCH
ES1003 - 3 Speed with Cord removed
ES1003CF - 3 Speed with Filter - Cord removed
ES100H2C - Humidity Control - Cord removed
N.B When installing fans via a remote
switch, pullcord switch must be left in "off"
position and the cord removed.
7
Page 8
SELV with Cord
ES1003CLV - 3 Speed with Cord
ES100H2CLV - Humidity Control with Cord
SELV Products
All SELV (safety extra low voltage) products must
be installed to conform to IEC 60364.
• Connection between the fan and the mains
supply must be by means of a safety isolating
transformer of the appropriate power rating
• The transformer should be connected to the
mains supply via a double pole safety switch
with a contact opening of at least 3mm
• The transformer will operate only one fan
• The transformer must not be installed in
Zones 1 or 2, but should be installed as close
as possible to the fan within Zone 3
• The cable used to connect the transformer to
the fan must be Class II, with a section area of
at least 1.5mm
• If the fan is a humidity control model, it must
be installed using the transformer supplied for
that product.
2
and a maximum length of 10m
SELV with Cord removed
ES1003CLV - 3 Speed with Cord removed
ES100H2CLV - Humidity Control - Cord removed
The ES1003 fans are designed to run con-
tinuously at one of 2 lower speeds fixed at
installation using the jumper switch. The
SELV models have 3 pins on the jumper
switch (rather than 2 as on the 230v models)
and are supplied ready for Speed 1 - lower
speed. Installer can change to Speed 2 if
required. The user can boost the fan speed
to its maximum performance by using cord
or remote switch (when installing with
remote switch, pullcord switch must be left
in "off" position and cord removed).
8
Page 9
OPERATION
ES1003, ES1003CF, ES1003LV - these fans
combine the latest technology with energy saving
and efficiency. They are quiet running, 3 speed
fans, designed to run continuously at a preselectable choice of 2 lower speeds (fixed at
installation). The user can boost the fan speed to
maximum performance when required by means
of the cord The fans can also be operated using
a remote switch (light, PIR, humidistat, etc)
instead of the cord. The ES1003 is SAP
Appendix Q Listed.
ES100H2C and ES100H2CLV - humidity control
models - the fans will start to operate automatically at their lower speed when the relative humidity
reaches the pre-set level and will continue to
operate at this speed until the humidity has been
dispersed. The user can use the cord to operate
the fan (at its higher speed), or to boost the fan
speed if it is already running. Pulling the cord
again will revert the fan to its lower speed, and it
will continue to run either until the humidity has
been removed, or the fan has completed the
timer over-run period (adjustable between 3 and
25 minutes). The fan's "comfortimer” technology
allows the fan to run at low speed for its over-run
period. The humidistat is adjustable from 40% to
90% relatve humidity. The fans can also be operated using a remote switch instead of the cord
(when installing with remote switch, pullcord
switch must be left in "off" position and cord
removed).
9
Page 10
ADJUSTMENT OF TRIMMERS
To adjust the humidistat and timer trimmers,
remove the front cover of the fan (Fig 13) and
open the plastic cover to access the trimmers (Fig
14).
The humidistat can be adjusted (Fig 15) between
40% and 90% relative humidity. Turn clockwise
to decrease sensitivity and set at a higher level of
relative humidity.
The timer is adjustable between 3 and 25 minutes. Turn the trimmer (Fig 16) clockwise to
increase the overrun time, or anti-clockwise to
decrease it.
10
Page 11
MAINTENANCE
Before any maintenance or cleaning operation,
switch off the fan and disconnect it from the main
power supply.
The front cover can be cleaned with a dry cloth or
soft brush
The fan must not come into contact with any kind
of liquid or solvent. If this should occur, contact a
qualified technician before reassembling the fan.
NOTE: The motor does not require lubrication
as it is maintenance free "sealed for life" type.
DISMANTLING & RECYCLING
This product has been designed
and constructed using high-quality
materials and components that can
be recycled or re-used.
Vectaire Ltd, Lincoln Road, Cressex Business Park, High Wycombe, Buckinghamshire, HP12 3RH
Tel: +44 (0)1494 522333. Fax: +44 (0)1494 522337.
Email: [email protected] Web: www.vectaire.co.uk
ESmile 240717
SF12125 Rev.2
E & O.E
Loading...