Vax VX28 User Manual

Download

User Guide

Designed in the UK

vax.com.au vax.co.nz VX28

Contents

Machine Overview

General Safety Information

Getting Started

Looking After Your Machine – Filters

FAQ s

Other Information

Machine Overview

Handle

Dirt container lid

Power On/O button

Inner separator

Hose connector

Base

Dirt container release button

Variable power

Cord rewind button

Main body

Wheel outer

Wheel inner and lter housing

Outer cyclone

Dirt container

TurboTool

Upholstery tool

Combination oor tool

Crevice tool

Flexible hose

Dusting brush

Tool storage clip

Telescopic wand

vax.com.au vax.co.nz

General Safety Information

This vacuum cleaner is intended for household use only and NOT for commercial or industrial use.

When using the vacuum cleaner basic safety precautions should always be observed, including the following:

1. Only use the vacuum cleaner indoors on dry surfaces.

2. Turn o the on/o switch on the vacuum cleaner controls before disconnecting or connecting from the mains supply.

3. Always unplug the vacuum cleaner before connecting or disconnecting the vacuum hose and accessories.

4. Children should be supervised to ensure that they do not play with the appliance.

5. This appliance is not intended for use by children and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance in a safe way and understands the hazards involved.

6. Cleaning and maintenance shall not be made by children.

7. The appliance should only be used as described in the quick start guide and in the full user guide.

8. Only Vax recommended attachments should be used with this appliance.

9. Do not use this vacuum cleaner if it has been dropped, damaged, left outdoors or dropped into water.

Do not use this vacuum cleaner with a damaged cord or plug.

10. Do not pull or carry this appliance by the cord. Do not use the cord as a handle, close a door on the cord or

pull the cord around sharp edges or corners. Do not run the vacuum cleaner over the cord. Keep the cord away from heated surfaces.

11. Do not handle the plug or the vacuum cleaner with wet hands.

12. Keep hair, loose clothing, ngers and all parts of the body away from openings and moving parts.

13. Do not pick up any hot coals, ash, cigarette butts, matches or any hot, smoking or burning objects.

14. Do not pick up any ammable or combustible materials (lighter uid, petrol, kerosene etc.) or use in the

presence of explosive liquids or vapours.

15. Do not vacuum harmful or toxic material (chlorine, bleach, ammonia, drain cleaner etc.).

16. Do not vacuum hard or sharp objects such as glass, nails, screws, coins etc.

17. Do not vacuum plaster dust, concrete dust or any other building or vitreous materials.

18. Do not vacuum baking soda or any other powder-based carpet refresher or deodoriser.

19. Store the vacuum cleaner in a cool, dry area.

20. Use only SAA approved 10amp extension cords. Non-approved cords may overheat. Care should be taken to

arrange the cord so that the cord cannot be tripped over.

21. Do not put any objects into openings. Do not use with any openings blocked and do not restrict airow.

Keep all openings free of dust, lint, hair or anything that might reduce airow.

22. Do not use the vacuum cleaner with blocked lters and without all of the lters in place.

23. Take extra care when positioning the vacuum cleaner on the stairs.

24. Keep vacuuming area well lit.

General Safety Information

WARNING: Always switch o and unplug the vacuum cleaner from the electrical socket before assembling,

opening or emptying the dirt container, or before connecting/disconnecting the attachments.

CAUTION: The vacuum cleaner is a very powerful unit. Before plugging the cord into the electrical socket,

make sure the switch is in the ‘o’ position.

IMPORTANT: If the inlet, hose or telescopic tube is blocked, switch o the vacuum cleaner and remove the

blockage(s) before re-starting the vacuum cleaner.

IMPORTANT: Vax recommends the use of Residual Current Device Rating of 30mA or less.

IMPORTANT: It is very important that lters are kept clean to obtain maximum performance from your vacuum

cleaner. Not cleaning and not replacing your lters regularly can reduce the suction power and

cause overheating and permanent damage to the vacuum cleaner.

NOTE: If the supply cord is damaged it must be replaced by the manufacturer, or a similarly qualied person

in order to avoid hazard, or invalidating the warranty.

IMPORTANT: The motor is equipped with a thermal cut-out. If for any reason the unit should overheat (eg. from

blocked nozzles, a full dust container or unclean lters), the thermostat will automatically turn o the

switch. Should this occur, unplug the vacuum cleaner from the electrical socket and turn o the switch.

Remove dirt container and empty. Clean lters. Allow the unit to cool for approximately one (1) hour.

To re-start, plug into an electrical socket and switch back on.

DAMAGE TO THE VACUUM CLEANER CAUSED AS A DIRECT RESULT OF NOT ADHERING TO THE GENERAL

SAFETY INFORMATION AND THE INSTRUCTIONS IN THIS USER GUIDE INVALIDATES THE WARRANTY

PLEASE KEEP THESE INSTRUCTIONS FOR FUTURE REFERENCE

vax.com.au vax.co.nz

Getting Started

Hard Floors

Carpets

PLEASE READ SAFETY INFORMATION BEFORE USE (p3-4)

Before plugging the cord into the electrical outlet, make sure the switch is in the ‘o’ position. Hold the vacuum cleaner rmly when starting and in use.

Assembling your cylinder

Insert the end of the hose into the unit. Ensure the hose has clicked into place.

How to use

Adjust the power for dierent surfaces as required.

Storage

Cable rewind button is located at the rear of the machine. After unplugging press the cable rewind until the cord is fully retracted.

Slot the metal telescopic extension tube and hose handle together. All accessories can be tted to the end of the metal telescopic extension tube.

For use on carpets click rocker switch forward. For use on hard oors click rocker switch back.

For convenience there is a parking slot located at the rear of the vacuum cleaner where the oor head and tubes can be attached for storage and carrying.

Fully unwind the power cord. A yellow mark on the cord indicates the recommended cord length. Do not exceed the cord beyond the yellow mark.

Plug in and switch the unit on by pressing the power button.

Looking After Your Machine - Filters

24hr

WARNING: Always switch o and unplug the vacuum cleaner from the electrical socket before assembling, opening or emptying the dirt container, or before connecting/disconnecting the attachments.

IMPORTANT: For best cleaning results lters require cleaning at least every three months. Do not use your vacuum cleaner with clogged lters and without all of the lters in place.

IMPORTANT: The motor is equipped with a thermal cut-out. If for any reason the unit should overheat, the thermostat will automatically turn the unit o.

Emptying and cleaning the dirt container

NOTE: Empty the dirt container when the MAX mark is reached.

Remove dirt container by pushing down the dirt container release button and lifting the dirt container.

Hold the dirt container and locate the dirt release button on the rear of the dirt container.

Hold dirt container over a bin and press dirt release button to open, allowing dirt to fall out.

Cleaning the pre-motor lter

Hold the dirt container and twist the lid anti-clockwise.

Tap excess dirt from the lter. Rinse under a tap and leave to dry at least for 24 hours before replacing in vacuum cleaner.

Lift the lid to reveal the pre-motor lter.

TAP

40˚C

MAX

Lift out the pre-motor lter.

NOTE: Check lters for cleanliness everytime you empty the dirt container. Clean where necessary. Replace lters when discoloured and/or damaged (frequency will depend on level of use).

vax.com.au vax.co.nz

Looking After Your Machine - Filters

TAP

Cleaning the shroud

Hold the dirt container and twist the lid anti-clockwise.

Remove the cap from the inner separator.

Lift the lid to reveal the pre-motor lter.

Dislodge any excess dirt by gently tapping the inner separator upside down above a bin.

Lift out the pre-motor lter.

Cleaning the Antibacterial HEPA media post-motor lter

Post-motor lter is located in the wheel. Hold the centre of the wheel and twist wheel cover anti-clockwise.

With the wheel cover o the post-motor lter is easily removed.

Tap all excess dirt o the lter.

Removing blockages from the TurboTool

Remove the inner separator from the container.

NOTE: Do NOT wash antibacterial HEPA media lter.

Locking ring

FAQs

Warning: To reduce the risk of personal injury, unplug the vacuum cleaner before performing maintenance/troubleshooting checks.

Is there an accessory missing?

• Check the ‘Getting Started’ page in this guide or the box that the machine came in to make sure that the part is denitely included in your unit.

• If it is missing, we’re here to help. Simply call us on AU 1300 361 505 / NZ: 0800 800 900

Why won’t the vacuum cleaner pick up?

• The lters may need cleaning, please refer to the ‘Looking After Your Machine – Filters’ page of this user guide (p6-7)

• The separator may be clogged, please refer to the ‘Looking After Your Machine – Filters’ page of this user guide (p6-7)

• There may be a blockage in the hose, please check the hose and remove the blockage

• The dirt container may be full or blocked, please refer to the ‘Looking After Your Machine – Emptying and cleaning dirt container’ page of this user guide (p6)

• The dirt container may be incorrectly installed, please ensure the dirt container is locked in place

Why won’t the accessories pick up properly?

• The TurboTool may be blocked, please refer to the ‘Looking After Your Machine – Removing Blockages’ page in this user guide (p7)

• The accessory may be broken

What do I do if an accessory/the unit becomes damaged or broken?

• Please check if the damage is with the accessory or the unit. To do this, rstly remove the accessory from the unit and check if there is suction from the hose. If there is suction from the hose this conrms that the damage is with the accessory.

Call us on AU 1300 361 505 / NZ: 0800 800 900

• If having done the above checks, checked the hose for blockages and cleaned the lters there is still no suction/limited suction from the hose, please call our Vax Careline on AU 1300 361 505 / NZ: 0800 800 900

Why is dust escaping from the vacuum?

• The lters may not be installed correctly, please refer to the ‘Looking After Your Machine – Filters’ page of the user guide (p6-7)

• The dirt container may be full or blocked, please refer to the ‘Looking After Your Machine – Emptying and cleaning dirt container’ page of this user guide (p6)

• The lters may need cleaning, please refer to the ‘Looking After Your Machine – Filters’ page of this user guide (p6-7)

• There may be a blockage in the hose, please check the hose and remove the blockage

Why does my vacuum cleaner have no power?

• It may not be plugged into the electrical socket correctly. Ensure that the plug is pushed into the electrical socket securely

• The electrical socket may not be working. Check the fuse or breaker and consult an electrician

• The motor thermostat may have tripped. Switch o and unplug the vacuum cleaner. Check the unit for blockages, clean the lters – please refer to the ‘Looking After Your Machine – Filters’ page of this user guide (p6-7) and clean the separator – please refer to the ‘Looking After Your Machine – Emptying and cleaning dirt container’ page of this user guide (p6). Leave the vacuum cleaner for 24 hours before switching the vacuum cleaner back on

Why does the vacuum cleaner cut out?

• The motor is equipped with a thermal cut-out. If for any reason the unit should overheat, the thermostat will automatically turn the unit o.

Should this occur, unplug the vacuum cleaner from the electrical socket and turn o the switch. Remove and empty the dirt container. Check the hose for blockages. Clean the lters. Allow the unit to cool for approximately 1 hour (if you have cleaned the lters you will need to wait 24 hours for the lters to dry before putting them back in the machine)

What do I do if the unit becomes damaged or broken?

• We’re here to help. Simply call AU 1300 361 505 / NZ: 0800 800 900 or visit vax.com.au / vax.co.nz

vax.com.au vax.co.nz

Other Information

Insulated

Use

Instructions

Service & Help

Vax Careline: (AU) 1300 361 505 (NZ) 0800 800 900

Monday-Friday 8.30am to 5.00pm

Any queries or concerns about using your Vax, call the Vax Careline. Calls are charged at the standard local rate. Please make a note of the serial number and model number of the steam cleaner before calling. For the nearest Service Agent, please call the Vax Careline or visit vax.com.au

Technical Specification

Voltage: 220–240V ~ 50Hz Wattage: 2000W Filters Pre-motor filter (washable) Antibacterial HEPA Post-motor filter (not washable) Capacity: 2.5L Cord length: 6m Cylinder weight: 4.9kg

Subject to technical change without notice.

Double

Indoor

Read