Vax VX30, VX23 User Manual

User Guide
Vax Careline: (AU) 1300 361 505 (NZ) 0800 800 900
vax.com.au
VX30
2
Machine Overview
1
Clean water tank carry handle
2
Clean water tank release lever
3
Clean water tank
4
Dirty water tank release lever
5
Dirty water tank carry handle
6
Dirty water tank
7
Brushbar (hidden)
8
Pre-motor filter (hidden)
9
Water/solution mix trigger
10
Cord storage hook
11
Upper cord storage
12
Power cord
13
Carry handle
14
Lower cord wrap clips
15
On/off button
16
Recline pedal
17
Vax carpet cleaning solution
18
Float chamber filter (hidden)
19
5
6
9
1
2
3
4
19
10
11
12
13
14
15
16
7
17
8
18 19
3vax.com.au
General Safety Information
FOR HOUSEHOLD USE ONLY.
When using the carpet washer, basic safety precautions should always be observed, including the following:
1. Do not leave the carpet washer unattended when plugged in. Unplug it from socket when not in use.
2. To prevent electric shock do not use outdoors.
3. Not to be used as a toy. Children should be supervised to ensure that they do not play with the appliance.
4. This appliance is not intended for use by persons (including children)with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning the use of the appliance by a person responsible for their safety.
5. Use only as described in this manual.
6. Do not use the carpet washer if it has been dropped, damaged, left outdoors or dropped into water. Do not use the carpet washer with a damaged cord or plug. If the supply cord is damaged, it must be replaced by the manufacturer or a recommended Service Agent to avoid hazard and invalidating the guarantee.
7. Do not pull or carry by cord. Do not use the cord as a handle, close a door on the cord or pull cord around sharp edges or corners. Do not run the carpet washer over the cord. Keep the cord away from heated surfaces.
8. Do not unplug by pulling on the cord.
9. Do not handle the plug or carpet washer with wet hands.
10. Do not put any objects into openings or operate with openings blocked, keep them free of anything that may reduce airflow.
11. Keep hair, loose clothing, fingers and all parts of the body away from openings and moving parts.
12. Do not use the carpet washer on any glowing, burning or smoking particles.
13. Do not use without the solution tank and dirty water tank in place.
14. Turn off all controls before unplugging.
15. Do not use to pick up flammable or combustible liquids such as petrol, or use in areas where they may be present.
16. Keep the unit on the floor.
17. Do not use an extension cord.
18. Do not attempt to remove blockages with sharp objects as they may cause damage.
19. Store indoors put away after use to prevent tripping accidents.
20. Using improper voltage may result in damage to the motor and possible injury to the user. The correct voltage is listed on the rating label.
21. A hazard may occur if the carpet washer runs over the power supply cord.
22. To prevent dirty water from running into the motor, do not hold the appliance upside-down or lay on its side. Use appliance in normal cleaning position.
23. Take extra care when cleaning on stairs.
24. Do not carry appliance while motor is running.
WARNING: Always switch off and unplug your machine from the electrical outlet before filling and emptying the clean water tank, emptying the dirty water tank, before assembling, opening, before connecting/disconnecting the attachments, or carrying out maintenance or troubleshooting checks.
NOTE: Carpets should be dry vacuumed thoroughly before washing.
IMPORTANT: If the hose or tools are blocked, switch off the carpet washer and remove the blockage(s) before re-starting your machine. See maintenance.
IMPORTANT: Even with regular cleaning, filters have a limited lifespan and will eventually need to be replaced during the lifetime of the cleaner. If the performance of your cleaner is compromised and/or the filters are severely discoloured, the filters may need to be replaced. As a general guide, Vax recommends filters be replaced every 3-6 months depending on the level of use to ensure optimum performance of your cleaner.
This machine is intended for household use only, and NOT for commercial or industrial use.
PLEASE KEEP THESE INSTRUCTIONS FOR FURTHER USE.
4
Getting Started
Assembling your carpet washer
Use a crosshead screwdriver.
Insert handle. Use a screwdriver to
Insert screw. Wrap cord to store.
tighten screw. Repeat on opposite side of unit.
Before you begin cleaning
NOTE: Do not over saturate your carpet.
• Vacuum thoroughly.
• Test for colourfastness -Wet a white absorbent cloth with the solution. In a small, hidden area of your carpet, gently rub the surface with the dampened cloth. Wait ten minutes and check for colour removal or bleed with white paper towel or cloth. If your carpet has more than one colour, check all colours.
• When cleaning an entire room, move furniture out of the area to be cleaned. If the furniture is too heavy to move, place aluminium foil or wax paper under legs. This will prevent wood finishes from staining your carpet. Pin up furniture skirts and curtains.
5vax.com.au
How To Use
Operating your carpet washer
IMPORTANT: Only use Vax carpet cleaning solution. Using other cleaning solution may cause excess
foaming and will prevent your machine from working effectively. Using other solutions will invalidate the warranty.
Pour required dose of cleaning solution (approx. 40ml per 1L of water).
Fill clean water tank with solution mix and re-fit the screw cap lid.
Recline the machine.
Mix solution with warm water (max 40°C).
Unwrap power cord and plug unit in.
Press trigger to release solution.
Remove clean water tank.
For best results apply solution on the forward stroke and recover solution on the backward stroke.
Unscrew tank lid and remove.
Turn machine ‘on’.
6
Looking After Your Machine
WARNING: To reduce the risk of electric shock, turn the machine off and unplug from electrical outlet
before performing maintenance/troubleshooting checks.
Emptying the dirty water tank
NOTE: Rinse out tank with clean water and leave to air dry before storing your machine.
Unclip dirty water tank.
Lift out the dirty water tank.
Cleaning the float chamber filter
Lift out chamber by gripping tab and pull.
Allow to dry completely before replacing or storing away your machine.
Unscrew tank cap.
Lift out sponge filter.
Empty water tank.
Rinse under water to remove debris (max 40ºC).
7vax.com.au
Looking After Your Machine
Cleaning the pre-motor filter
The pre-motor filter is located under the dirty water tank.
Rinse under water to remove debris (max 40ºC).
Allow to dry completely before replacing or storing away your machine.
Removing blockages from the brushbar
WARNING: To reduce the risk of electric shock, turn the machine off and unplug from electrical outlet
before performing maintenance/troubleshooting checks.
To locate the brushbar turn your machine upside down. Threads caught in the brushbar may be removed.
8
FAQ
WARNING: to reduce the risk of personal injury, unplug the steamer and ensure unit has fully cooled down before performing maintenance/troubleshooting checks.
Is there an accessory missing?
• Check the ‘Parts Overview’ page in this guide to make sure the part is definitely included in your unit.
Why won’t the carpet washer turn on?
• It may not be plugged into the electrical outlet correctly: ensure that the plug is pushed in securely and switched on.
• The power button on the unit hasn’t been fully depressed.
• If unit cuts out during use, disconnect the unit from the wall socket, allow to cool for one hour, clean the filter and empty the dirty water tank and check hose, brushbar for blockages.
Why won’t the cleaner pick up solution/spills?
• The dirty water tan may be full and the auto shut off engaged. Empty the dirty water tank.
• Ensure the dirty water tank is fitted correctly and the tank cap is securely fitted.
• Check the brushbar for blockages.
Why won’t the solution/clean water dispense?
• Ensure the clean water tank is fitted securely.
• The solution/clean water tank may be empty.
• Ensure dirty water tank is fitted securely.
we’re here to help
For troubleshooting please
call or visit our website:
AU: 1300 361 505
vax.com.au
NZ: 0800 800 900
vax.co.nz
9vax.com.au
Other Information
Service & Help
Vax Careline: (AU) 1300 361 505 (NZ) 0800 800 900
Monday-Friday 8.30am to 5.00pm
Any queries or concerns about using your Vax, call the Vax Careline. Calls are charged at the standard local rate. Please make a note of the serial number and model number of the steam cleaner before calling. For the nearest Service Agent, please call the Vax Careline or visit vax.com.au
Technical Specification
Voltage: 220–240V ~ 50Hz Wattage: 500W Capacity Clean water tank: 2.1L Dirty water tank: 1.7L Cord length: 6m Weight: 5.6kg Filter Float chamber filter - foam Pre-motor filter - foam
Subject to technical change without notice.
Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist. Check with your Local Authority or retailer for recycling advice..
10
11vax.com.au
Distributed by Techtronic Industries Australia Pty. Ltd.
31 Gilby Road, Mt Waverley, VIC 3149 Australia
www.vax.com.au Careline AU: 1300 361 505
www.vax.co.nz Careline NZ: 0800 800 900
Loading...