Vax VSTM1500 User Manual

User Guide
Vax Careline Australia: 1300 361 505
New Zealand: 0800 800 900
Stick Steam Cleaner
Get Cleaning...
What’s your Vax’s model number?
V S T M 1 5 00
What’s your serial number? (Located on the base of the machine)
Note these down in case you need them in future. Please keep instructions for further use.
vax.com.au
VSTM1500
Machine Overview
1 Handle 2 Upper cord clip 3 Lower cord clip 4 Power cord 5 Clean water tank 6 Steam tank/power indicator
unit on
Green light = steamer ready
No light = tank heating
7 Floor head 8 Steam release trigger
Microfibre cleaning pad x 2
9
Carpet glider
10
Measuring jug
11
Hard water filter (hidden)
12
(Pre-assembled in unit)
Resting tray
13
Unit
Accessories
9
8
1
2
4
3
5
12
6
7
10
13
2
11
12
Vax Careline Australia: 1300 361 505
New Zealand: 0800 800 900
General Safety Information
FOR HOUSEHOLD USE ONLY.
Whenusing the steam mop, basic safety precautions should always beobserved, including the following:
1 . Turn off the steam mop controls before
disconnecting or connecting from the mains supply.
2. Always unplug thesteam mop before connecting
or disconnectingthe vacuum hoseand accessories.
3. Children should be supervised to ensure that they
do not playwith the appliance.
4. This appliance is not intended for use by persons
(including children) with reduced physical, sensory
or mental capabilities, or lack of experience and
knowledge, unless they have been given supervision
uction concerning use of the appliance by a
r
or inst person responsible for their safety.
5. Use only as described in this manual. Use only Vax
recommended attachments.
6. Do not use the steam mop if it has been
dropped, damaged, left outdoors or dropped into
water. Do not use the steam mop with a damaged
cord or plug. If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard.
7. Do not pull or carry by cord. Do not use the cord
as a handle, close a door on the cord or pull cord
around sharp edges or corners. Do not run the
steam mop over the cord. Keep the cord away from heated sur
8. Do not handle the plug or steam mop with wet
hands. Do not use outdoors or on wet surfaces.
9. Do not put any objects into openings. Do not use
with any openings blocked and do not restrict air-
flow. Keep all openings free of dust, lint, hair or
anything that might reduce airflow.
10. Keep hair, loose clothing, fingers and all parts of
the body away from openings and moving parts.
aces.
f
11 . Do not steam clean harmful or toxic material
(chlorine, bleach, ammonia, drain cleaner etc.).
12. Keep cleaning area well lit.
13. Store the steam mop in a cool, dry area.
14. Turn off the on/off switch before unplugging the
steam mop.
15.WSymbol IEC 60417-5597 (2002-10) is used on the unit to indicate the following:
WARNING: Danger of Scalding
!
ARNING: Always switch off and unplug the
!
steam cleaner from the electrical outlet before
assembling, opening or emptying the water container, or
beforecon
!
outlet, make sure the switch is in the ‘off’ position. Hold the
steam cleaner firmly when starting and in use.
!
!
return the mop back to the resting pad when not in
use or when not continuously moving across the floor.
This steam cleaner is intended for household use only and NOT for commercial or industrial use.
PLEASE KEEP INSTRUCTIONS FOR FURTHER USE.
cting/disconnecting the attachments.
ne
CAUTION: The steam cleaner is a very powerful
unit. Before plugging the cord into the electrical
IMPORTANT: We recommend the use of a Residual Current Device with a Residual Current
rating of 30mA or less.
WARNING:
spot on any surface for an extended period of
time as this may damage the floor surface. Always
IMPORTANT: This steam mop may not be suitable for all floating floorboards - please check with your
!
floorboard manufacterer first prior to use.
Never leave the steam mop in one
vax.com.au
3
--
Operation
Assembling your stick steam cleaner
Remove clean water tank. Insert handle into main body.
Fit the body of the unit onto the floor head, lining up the screw hole.
Line up the screw holes on the handle and the main body.
Secure the floor head with the remaining screw.
Secure the handle in place with one of the screws provided.
4
Vax Careline Australia: 1300 361 505
New Zealand: 0800 800 900
Operation
Before you begin cleaning
For best results, thoroughly sweep or vacuum floors prior to cleaning with the steam mop.
WARNING: To reduce the risk of personal injury, unplug the steamer when assembling the unit.
Remove the clean water tank.
NOTE: In hard water areas, or to prevent calcium and mineral deposits from accumulating on the heating element and mop head, you may use distilled or demineralized water in place of tap water.
Twist the cap anti­clockwise to remove.
Fill the tank with 500ml (2 measuring jugs) of water and replace the water cap. Tighten by twisting clockwise. Make sure water levels do not exceed the MAX fill line on jug. DO NOT OVERFILL.
Replace the clean water tank, clicking into place making sure the hard water filter is in place.
Attaching the microfibre cleaning pad
WARNING: To reduce the risk of personal injury, unplug the steamer when assembling
the accessories.
WARNING: Never use the steam stick without the microfibre cleaning pad correctly attached to the floor head.
IMPORTANT: Place the steamer on the resting tray whilst the steam is heating and when
the product is not moving continuously on the floor.
Place the microfibre cleaning pad over the floor head.
Tighten the drawstring so the microfibre cleaning pad is fitted securely.
vax.com.au
5
--
Operation
Steam cleaning hard floors
WARNING: Never leave the stick steamer in one spot on any surface for an extended
period of time as this may damage the floor surface. Place on the resting tray whilst the steam is heating and when the product is not moving continuously on the floor.
WARNING: Your stick steamer should only be used on tiles, lino or sealed wood flooring. Do not use on laminated flooring and if using the product on floating floor boards – check with the manufacturer of this flooring before use if it is suitable.
WARNING: Never use the steam stick without the microfibre cleaning pad properly attached to the floor head.
WARNING: To reduce the risk of personal injury, unplug the steamer when assembling the accessories.
IMPORTANT: Check the water tank viewing window to ensure there is adequate water in the water tank.
IMPORTANT: Do not put solutions or detergents into the water tank. This machine operates with water & steam only.
Plug into mains and wait for the green light (on the main body) to switch on. This takes approx. 30 seconds.
6
To recline the unit place foot on floor head and tilt handle.
To produce steam squeeze the trigger. A hissing noise will be heard as the steam begins. Steam will wet the microfibre cleaning pad. If you want to stop the steam, press the trigger again.
Move the steam stick slowly backwards and forwards across the floor paying particular attention to high traffic areas.
Vax Careline Australia: 1300 361 505
New Zealand: 0800 800 900
Operation
Refreshing carpets
WARNING: Your Steam Mop is designed to clean carpets or rugs that will withstand high
heat. Be sure to check the Use and Care Instructions from the carpet manufacturer before steam cleaning.
WARNING: The carpet glider accessory is for use on carpeting and rugs only. Use of the carpet glider on other floor will cause streaking and possible scratching of the floor’s surface.
IMPORTANT: Never use the Steam Mop without the microfiber cleaning pad properly attached to the mop head.
IMPORTANT: Check the water tank viewing window to be sure there is adequate water in the water tank.
For best results, thoroughly vacuum the carpets or rugs prior to steam cleaning.
1. Place the mop head (with microfiber cleaning pad in place) on top of the carpet glider.
2. Do not attempt to use the Steam Mop on carpet/rug surfaces without the carpet glider in place!
CAUTION: Never use the carpet glider on surfaces that are prone to scratching.
CAUTION: The Steam Mop emits steam and creates moisture. If the Steam Mop operates
too long in one place, water marks can result.
Attach carpet glider attachment to floor head by pushing the steam stick onto it.
IMPORTANT:
water/steam. As the water tank empties, a special water sensor will cause the unit to work intermittently and eventually stop running in order to protect the pump inside the unit. A vibrating sound may be heard, and the green indicator light will turn orange. The pump will turn OFF.
WARNING: Never leave the Steam Mop in one spot on any surface for an extended period of time as this may damage the floor surface. Always return the mop back to the resting tray when not in use or when not continuously moving across the floor.
vax.com.au
To recline the unit place foot on floor head and tilt handle.
Pay attention to the water tank’s viewing window to monitor remaining
To produce steam squeeze the trigger. If you want to stop the steam, press the trigger again.
Move the steam stick slowly backwards and forwards across the floor paying particular attention to high traffic areas.
7
Maintenance (Keep your Vax as good as new)
Empty the water tank
IMPORTANT: Allow the unit to fully cool down before performing any maintenance or
troubleshooting checks.
Remove the clean water tank. Twist the cap anti-clockwise
to remove.
Empty any excess water over the sink, replace water cap and return to the unit.
Remove the microfibre cleaning pad from the unit
IMPORTANT: Allow the unit to fully cool down before performing any maintenance or
troubleshooting checks.
Undo drawstring.
Remove microfibre cleaning pad.
Cleaning the microfibre cleaning pad
To ensure long life and continued cleaning ability, proper care of your microfibre cleaning pad is required. Read and follow cleaning instructions.
1. Microfibre cleaning pads can be machine washed in warm water with a mild detergent after each use or when dry.
CAUTION: Never use bleach or fabric softener.
IMPORTANT: Only use liquid detergent or soap.
2. Air dry pads for 24 hours.
NOTE: Cleaning pads may be machine tumble dried on low heat.
Vax Careline Australia: 1300 361 505
8
New Zealand: 0800 800 900
Maintenance (Keep your Vax as good as new)
3. To avoid passing or picking up lint from the cleaning pads, wash the microfibre cleaning pads separately or place them in a garment bag.
IMPORTANT: Wash microfibre cleaning pads regularly. As with any fabric, dirt particles can cause the fibers to break down. Therefore regular cleaning will help preserve the cleaning efficiency of the microfibre cleaning pads.
4. As the microfibre cleaning pad is used, sometimes a thread will loosen or pull out. This is normal. Never pull loose threads as this can cause the weave to come undone. Simply trim any loose threads with a pair of sharp scissors.
Care & Cleaning
1. Always unplug and allow the Steam Mop to cool completely before cleaning or moving.
2. Press the round black lock and pull it downwards to loosen the microfibre cleaning pad’s drawstring.
CAUTION: Carefully remove the cleaning pad from the mop head, as mop pad and lower assembly may be hot.
4. Any water remaining in the water tank should be emptied before storing the Steam Mop.
5. Wipe all exterior surfaces of Steam Mop with a damp or dry, soft cloth.
Storage
1. Never store the Steam Mop while it is still plugged in. Remove the plug from the electrical outlet.
2. Empty water from the water tank before storing.
3. Wrap cord for storage.
4. Store upright in a protected, dry area. Keep water fill cup and funnel handy for future use.
Replacing the hard water filter
IMPORTANT: The condition of the filter affects the performance of your machine.
Check and change filter regularly (depending on level of use).
Your machine is fitted with a hard water filter. If you live in an area of hard water the filter will discolour/darken over time. Depending on water hardness and/or frequency of use the filter should be changed every 6 months.
vax.com.au
9
Other Information
Service & Help
Vax Careline:
If you have any queries about using your Vax, call the Vax Careline. Please make a note of the serial number and model number of your product before calling. For the nearest Service Agent, please call the Vax Customer Careline or visit
Technical Specification
Voltage: 220 240 v ~ 50Hz Wattage: 1500W Water tank capacity: 500ml Cord length: 5.8m
Heating time: 30 seconds
Weight: 3.2kg
Subject to technical change without notice.
EEC Statement of Compliance
Manufacturer/EEC importer: Vax Limited, hereby on our own responsibility, declare that the steam cleaner series is manufactured in compliance with the following Directives:
Safety: 2006/95/EC Low Voltage Directive EMC: 2004/108/EC Electromagnetic Compatibility Directive
Waste electrical products shouldnot bedisposedof with household waste.Please recycle where facilitiesexist. Check with your LocalAuthority or retailer for recyclingadvice.
S2 Hard Floor Master User Guide v1.1.qxd:User guide 6/10/10 11:36 Page 10
FAQs
WARNING: To reduce the risk of personal injury, unplug the steam stick before performing maintenance or trouble shooting checks.
Is there an accessory missing?
Check the Parts Overview page in the guide to make sure the part is definitely included in your unit
If the part is missing we’re here to help. Simply call
Why won’t the steam stick run?
Unit may not be plugged into the electrical outlet
The electrical outlet ma
The power cord may be damaged, if it is it must be
What do I do if an accessory/the unit has become damaged or broken?
Please call our Careline to purchase new spares
Australia: 1300 361 505
us on:
New Zealand: 0800 800 900
correctly, ensure the plug is pushed in securely
check the fuse or breaker, or consult an electrician
replaced by the manufacturer or similarly qualified person
or order a replacement
y not be working properly,
Why is the steam stick not producing steam?
There may be no water in the tank; please refer to the operation section
The water tank may not be fitted corre refer to the operation section
Why won’t the microfibre cleaning pad pick up dirt?
The cleaning pad may already be saturated with dirt and needs washing, please refer to the maintenance section
ctly; please
Don’t take your machine back to the shop, simply contact us
vax.com.au Australia: 1300 361 505 New Zealand: 0800 800 900
This does not affect your statutory rights.
Vax Careline Australia: 1300 361 505
10
New Zealand: 0800 800 900
S2 Hard Floor Master User Guide v1.1.qxd:User guide 6/10/10 11:36 Page 10
Other Information
Service & Help
Vax Careline:
Australia: 1300 361 505 New Zealand: 0800 800 900
Monday– Friday 8.30am to 5.00 pm
If you have any queries about using your Vax, call the Vax Careline. Please make a note of the serial number and model number of your product before calling. For the nearest Service Agent, please call the Vax Customer Careline or visit
Technical Specification
Voltage: 220 – 240 v ~ 50Hz Wattage: 1500W Water tank capacity: 500ml Cord length: 8m Weight: 3.2kg Heating time: 30 seconds
Subject to technical change without notice.
vax.com.au
EEC Statement of Compliance
Manufacturer/EEC importer: Vax Limited, hereby on our own responsibility, declare that the
steam cleaner series is manufactured in compliance with the following Directives:
Safety: 2006/95/EC Low Voltage Directive EMC: 2004/108/EC Electromagnetic Compatibility Directive
Waste electrical products shouldnot bedisposedof with household waste.Please recycle where facilitiesexist. Check with your LocalAuthority or retailer for recyclingadvice.
vax.com.au
11
Distributed by Techtronic Industries Pty. Ltd.
www.vax.com.au. Service Line: AU: 1300 361 505 / NZ: 0800 800 900
Level 1, 660 Doncaster Rd, Doncaster, Australia 3108.
VSTM1500vax.com.au
Loading...