vax.co.uk
U86-PM Series
Performance Floor2Floor
Let’s get started
Do’s
Basic safety precautions
3 Turn o all controls on the vacuum cleaner before
disconnecting or connecting the power cord
3 Always keep the power cord away from the brushes
whilst using your vacuum cleaner. After use always
wrap the power cord around the cord clips provided
3 Always make sure both the pre-motor/post motor
lters are in place before use
3 Always switch o the vacuum cleaner before
disconnecting or connecting the hose and accessories
3 Keep all openings clear and free from debris as this
may aect the airow/suction
3 Always replace the fuse in the plug with a 13amp fuse.
Always protect the power cable from heated surfaces
and open ames
3 Use only CE approved 13amp extension cords, non-
approved extension cords may overheat. Care should
be taken to arrange the extension cord as it can be a
trip hazard
Don’ts
8 Don’t use this vacuum cleaner if it has been dropped,
damaged or left outdoors
8 Don’t run over the power cord or use vacuum cleaner
if the power cord or plug is damaged. Please contact
our Customer Care Line on: 0844 4128 455
(Mon-Fri 8.30am to 6.30pm, Sat 9.00am to 5.00pm)
8 Don’t handle the plug or use the vacuum cleaner with
wet hands
8 Don’t vacuum up any ammable or combustible
materials (lighter uid, petrol, kerosene etc.) or use the
vacuum cleaner in an area with explosive vapours
or liquid
8 Don’t vacuum up hot coals, cigarette butts, matches or
smoking hot burning items or use in an area where
there may be harmful uids (chlorine, bleach, and
ammonia drain cleaner)
8 Don’t attempt to remove blockages with sharp objects
as this may cause damage to your vacuum cleaner
8 Don’t vacuum up hard or sharp objects such as glass,
nails, screws or coins etc
8 Don’t use the vacuum cleaner with incorrect voltage
as this may result in damage or injury to the user. The
correct voltage is listed on the ratings label
Let’s talk safety
This vacuum cleaner is intended for household use
only and NOT for commercial or industrial use.
• Only use the vacuum cleaner indoors on dry surfaces
and keep the area your cleaning well lit
• Keep ngers, hair and loose clothing from moving parts
and openings whilst using the vacuum cleaner
• This appliance can be used by children aged from 8
years and above and persons with reduced physical,
sensory or mental capabilities or lack of experience
and knowledge if they have been given supervision or
instruction concerning use of the appliance in a safe
way and understand the hazards involved. Children
shall not play with the appliance. Cleaning and user
maintenance shall not be made by children
without supervision
• Only Vax recommend tools should be used with this
vacuum cleaner
Thank you for buying this Performance Floor2Floor.
Taking care of your carpets
The Performance Floor2Floor is designed to make vaccuming carpets regularly, as eective and
ecient as possible and this user guide will help you get the most out of your machine.
Maintaining your carpets will ensure they keep their appearance for longer .
You’ve chosen carpets for your home for a reason and Vax will help you
take good care of them.
Taking care of your Performance Floor2Floor
Also inside this guide are instructions on maintaining your new machine, so that it’s always ready
when you are to tackle your carpets.
Taking care of you
We’re here if you need us. Instead of taking me back
to the shop, simply visit:
vax.co.uk/support or call:
(UK) 0844 412 8455 (ROI) 1-800 928 308
Monday-Friday 8.30am to 6.30pm, Saturday 9.00am to 5.00pm
Calls are charged at the UK local rate. Before you call we’ll need you to have the following
information to hand: Your Machine, Your Proof of Purchase or Warranty registration code.
Alternatively, you can write to us at:
Vax Ltd., Kingswood Road, Hampton Lovett, Droitwich, Worcestershire, WR9 0QH, UK
Let us know what you think @VaxUK
Contents
Let’s talk safety
Getting to know your machine
Getting started
Using your machine
Taking care of your machine
Let’s talk technical
What to do if it goes wrong
Getting in touch
Notes
Performance Floor2Floor
2 in 1 tool
Included with
your machine
Floor2Floor Pet
+
TurboTool
Pre-motor lter
Post-motor lter
Floor2Floor Total Home
+
Flexi-crevice tool
Flat upholsery tool
TurboTool
Getting to know your machine
Hose
Name Performance Floor2Floor
Voltage 220-240V~50Hz
Wattage 1600W
Cord length 8/10m
Weight 6.5kg
Technical Specication
Subject to technical change without notice.
Handle
Extension tube
Dirt container release button
Power on / o button
Pre-motor lter
Separator
Dirt container
Post-motor lter
Carpet height
adjuster
Handle release button
Quick release
cord hook
Hose to
machine connector
Filter Kit (Type 70)*
1-1-132540-00
Belt Kit (Type 1)*
1-1-130669-01
Pro Cleaning Kit (Type 2)
1-1-133326-00
Turbo Tool (Type 1)
1-1-126261-00
Flat Upholstery Tool
1-1-131394-00
Flexi Crevice Tool (Type 2)
1-1-131393-00
2 in 1 Tool (Type 3)
1-9-132115-00
Accessories & Consumables
*To purchase consumables and accessories, please visit vax.co.uk
Insert the back panel
into the oorhead
Insert the lower cord
hook into the hole
at the bottom of the
back panel
Now take the small
clip and push it down
between the end of the
cord hook and the
machine, to lock the
cord holder in place
Place the dirt container onto the machine.
Ensure the dirt container tabs line up with
the holes in the post motor lter cover
Assembling your upright
Ensure that the back of
the dirt container connects
to the inlet tube
Place dirt container on
machine and click into
place at the back panel
Insert the short end of the
hose into the tube at the
back of the machine and
turn to lock
Wrap the hose around the
machine and push the
hose end into the hose to
machine connector
Getting started
PLEASE READ ‘LEt’S tALk SAFEtY’ At tHE BEGINNING BEFORE USE
Wrap the power cord around the quick release cord hook
at the top and the lower cord hook, continue wrapping
the power cord until it is secure
Attach TurboTool clip to the
handle. Snap TurboTool
into position*
Inset the handle into the
top of the back panel until
it clicks into place
*Not applicable for all models
Unit must be in the upright
position to change the oor mode
WARNING
Before you begin cleaning
• Always switch o and unplug the vacuum cleaner before connecting or disconnecting the hose/attachments, or
removing and emptying the dirt container.
• The vacuum cleaner is equipped with a thermal cut-out. If for any reason the vacuum cleaner does overheat the
thermostat will automatically turn the vacuum cleaner o. If this happens, switch the vacuum cleaner o and unplug
from electrical socket. Remove and empty the dirt container also check the vacuum cleaner for blockages. Allow the
vacuum cleaner to cool for approximately 1 hour (if you have cleaned the lters please wait 24 hours for the lters to
fully dry before putting back into the vacuum machine)
• For best cleaning results lters require cleaning at least every 3 months.
• If the vacuum cleaner is blocked, switch o and unplug before removing the blockage.
Push the on/o switch to
turn machine on
Place your foot gently on the
oorhead and pull the handle
backwards to recline the machine
Using your machine
Remove hose end from
the oorhead
Choose an accessory* Attach accessory
to hose end/extension
tube/adapter
Push the quick release
cord hook to one side to
release the power cord
Turn the height adjuster
dial backwards for the
carpet setting
Turn the height adjuster dial forwards for the hard oor setting,
the oorhead will tilt forward
*Not applicable for all models
Using accessories
Attach extension tube/
adapter if necessary to
hose end
MAX
40˚C
T
A
P
24hr
Cleaning the pre motor lter
Taking care of your machine
Press dirt container release
button to remove the dirt
container
Place ngers under the
catch of the dirt container
lid and pull to release it
The lid will lift on a hinge Use the tab on the lter to
pull the lter out of
it’s housing
Tap the lter over a bin
to release dirt
Hold the dirt container over a bin
and unclip the lock on the bottom
of the dirt container, allowing the
dirt to fall out
Close the base of the dirt
container and click the dirt
container back on to the
back panel
Emptying and cleaning the dirt container
MAX
40˚C
24hr
24hr
Wash the lter under running
water (40 degree max)
Leave to fully dry for a least
24 hours before placing back
in the machine
Place ngers under the
catch of the bin to dirt
container lid and pull to
release it
Press dirt container
release button to remove
the dirt container
24hr
MAX
40˚C
Cleaning the shroud
Cleaning the post motor lter
Taking care of your machine
Remove the pre-motor
lter to allow access to
the shroud
Remove the exhaust cover
by turning it counter clockwise
and lifting it o. To nd the
post-motor lter
Tap the shroud over the
bin to release dirt
Wash the shroud under
running water and leave
to dry. The shroud will need
to be placed back correctly
Remove the lter Tap the post-motor lter
over a bin to release the dirt.
Then replace before using
your vacuum
Always switch o and uplug the
vacuum cleaner before carrying
out any maintenance
WARNING
Removing blockages from the TurboTool*
3
4
1 2
3
4
3
4
4
Removing debris
from the brushbar
Vacuuming the stairs
Switch o your vacuum
cleaner at the main socket.
Using a pair of scissors
cut any hair or debris free
from around the brushbar
Ensure that the vacuum
is upright at the top or
bottom of the stairs while
vacuuming. Do not lean
on the machine while using
the hose
Let’s talk technical
*Not applicable for all models
Changing the belt
Changing the belt
Switch o your vacuum
cleaner at the main socket
and unplug. Remove the
6 screws on the bottom
of the oorhead
Lift the brush from the
machine starting at the
side without the belt on
Squeeze the sides of the
oor plate to release it
Unhook the belt from the
motor spindle in the belt
compartment. (This may
be easier if you use a
screwdriver to do this)
Remove the oor plate
Place the new belt
around the brush bar
Remove the belt cover
Let’s talk technical
Feed the other side into
the belt compartment
Using a screwdriver,
hook the belt onto the
motor spindle
Reinsert the brushbar. One end of the
brushbar has a square slot, and one end
has a circular slot, ensure that it is put
back into the correct position
• The vacuum cleaner is making a whistling noise, please remove the
dirt container open the bottom and clean the seals.
Replace the dirt container and retry
• If there is air sucking noise from the top of the dirt container, this
would indicate a blockage in the machine Go to ‘Why won’t the
vacuum cleaner pick up above’
SolutionProblem
Warning: To reduce the risk of personal injury, unplug the vacuum cleaner before performing maintenance
/troubleshooting checks.
What to do if it goes wrong
• The plug may not be fully pushed into the electrical socket
• Check the fuse in the plug if this needs replacing, always
replace with a 13amp fuse
• The motor thermostat may have tripped. If this has happened,
unplug the vacuum cleaner. Remove and empty the dirt container and
check the hose for blockages Clean the lters and allow the vacuum
cleaner to cool for approximately 1 hour (if you have washed the lters
you will need to wait 24 hours for the lters to fully dry before putting
them back into the vacuum cleaner)
Why won’t the vacuum
cleaner turn on?
What if my vacuum
cleaner is making an
excessive noise?
• The brushbar may be jammed. If this happens then the machine
needs to be switched o immediately to avoid damage. To remove
debris from brushbar refer to page.
• The belt might not turn if it is broken. To check the belt, go to
the‘Changing the belt’ page.
My brushbar
isn’t turning?
• There may be a blockage in the hose. Please remove the hose from the
vacuum cleaner, check and clear any blockages
•
Empty the dirt container and clean lters. Go to the
Let’s maintain section page *’
• The brushbar may not be turning.
Go to ‘My brushbar isn’t turning?’ below
• If the accessory/tool will not pick up, check and clear
any blockages
Why won’t the vacuum
cleaner pick up?
• Check the ‘This pack contains’ panel on the box to make sure
the part is included with your machine.
There is an accessory
missing?
Getting in touch
* Calls are charged at the UK local rate. Please make a note of the serial number and model number of the vacuum cleaner
before calling.
Accessories
Don’t forget your accessories!
Order at: www.vax.co.uk/spares-and-solutions
Pro cleaning kit
1-1-133326-00
All our best tools all in one kit that makes cleaning
your home quicker, easier and with even better results.
We’ve taken care of cleaning all of the hard to reach
areas such as on top of cupboards and in between
blinds to the dust that collates behind and
within the radiator.
Flexi Crevice Tool
1-1-131393-00
A handy long, exible tool for getting far behind and
around furniture.
TurboTool
1-1-126261-00
Use the TurboTool for vacuuming your stairs,
upholstery and car interiors. It’s great for picking up
stubborn pet hair.
Flat Upholstery Tool
1-1-131394-00
Cleans large areas of upholstery like sofas and
curtains, quickly and eectively.
2 in 1 Tool
1-1-132115-00
2-in-1 tool includes crevice tool for awkward areas
and corners and a dusting brush for areas such
as skirting.
Notes
Vax Ltd., Kingswood Road, Hampton Lovett, Droitwich, Worcestershire, WR9 0QH, UK
email: info@vax.co.uk website: vax.co.uk
Version 2.0
EEC Statement of Compliance: Manufacturer/EEC importer: Vax Limited, hereby on our own responsibility,
declare that the Dual Power series is manufactured in compliance with the following Directives:
Safety: 2006/95/EC Low Voltage Directive. EMC: 2004/108/EC Electromagnetic Compatibility Directive
Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist.
Check with your Local Authority or retailer for recycling advice.
@VaxUK
Loading...