BAGGED CYLINDER VACUUM CLEANER
Instruction Manual
Please read carefully before using
this cleaner. Always fully extend
the mains cable before use.
Vax Careline:
UK 0844 412 8455
ROI 1-800 928 308
vax.co.uk
Vax Model Number: V-100T
2 pc extension tube
Flexible hose
Combination floor tool
Castor wheels
Top cover retainer clips
Post-motor filter (at rear)
Power cord
On/off button
Carry handle
Dusting brush
Crevice tool
Upholstery tool
Dust bags (x3)
IMPORTANT: The accessories are stored in the dust bag compartment and need to be removed before operating
the vacuum cleaner.
2
6
Parts Overview
1. Parts Overview
Fig. 1/1
9
8
7
5
2
1
3
4
13
10 11 12
1
2
3
4
5
6
7
8
13
12
11
10
9
2. Safety Information
Safety Information
FOR HOUSEHOLD USE ONLY
When using the vacuum cleaner, basic safety
precautions should always be observed, including
the following:
1. Only use the vacuum cleaner indoors on dry
surfaces. Do not handle the plug or vacuum
cleaner with wet hands. Do not use outdoors or
on wet surfaces.
2. Turn off the vacuum cleaner controls before
connecting to or disconnecting from the mains
supply.
3. Always unplug the vacuum cleaner before
connecting or disconnecting the vacuum hose.
4. Close attention is necessary when used by or
near children. Do not allow children to use as a
toy.
5. Use only as described in this manual. Use only
the manufacturer’s recommended attachments.
6. Do not use the vacuum cleaner if it has been
dropped, damaged, left outdoors or dropped into
water. Do not use the vacuum cleaner with a
damaged cord or plug. If the supply cord is
damaged, it must be replaced by the
manufacturer or a recommended Service Agent
to avoid hazard and invalidating the guarantee.
7. Do not pull or carry by the cord. Do not use the
cord as a handle, close a door on the cord or pull
the cord around sharp edges or corners. Do not
run the vacuum cleaner over the cord. Keep the
cord away from heated surfaces.
8. Do not put any objects into openings. Do not use
with any openings blocked and do not restrict air
flow. Keep all openings free of dust, lint, hair or
anything that may reduce airflow.
9. Keep hair, loose clothing, fingers and all parts of
the body away from openings and moving parts.
10. Do not pick up hot coals, cigarette butts,
matches or any hot, smoking or burning objects.
11. Do not pick up flammable or combustible
materials (lighter fluid, petrol, kerosene, etc) or
use in the presence of explosive liquids or
vapours.
12. Do not vacuum up harmful or toxic material
(chlorine bleach, ammonia, drain cleaner etc).
13. Do not vacuum up hard or sharp objects such as
glass, nails, screws. coins etc.
14. Do not use without the filters in place.
15. Take extra care when vacuuming on stairs.
16. Keep vacuuming area well lit.
17. Store the vacuum cleaner indoors in a cool, dry
area.
18. Turn off the switch before unplugging.
19. Use only CE-approved 1 amp extension cords.
Non-approved extension cords may overheat.
Care should be taken to arrange the cord so that
the cord cannot be pulled or tripped over.
WARNING: Always switch off and unplug the vacuum
cleaner from the electrical outlet before assembling,
opening or replacing the dust bag, or before
connecting/disconnecting the attachments.
CAUTION: The vacuum cleaner is a very powerful
unit. Before plugging the cord into the electrical
outlet make sure the switch is in the ‘off’ position.
Hold the vacuum cleaner firmly when starting and in
use.
IMPORTANT: If the inlet or hose is blocked, switch off
the vacuum cleaner and remove the blockage(s)
before re-starting the vacuum cleaner.
IMPORTANT: Replacing filters and changing the dust
bag improves vacuum performance. Make sure the
foam filter sleeve is completely dry before inserting
back into the vacuum cleaner.
This vacuum cleaner is intended for household use
only and not for commercial or industrial use.
PLEASE KEEP THESE INSTRUCTIONS FOR
FURTHER USE.
Motor Thermostat
IMPORTANT: The motor is equipped with a thermal
cut-out. If for any reason, the vacuum cleaner should
over-heat, the thermostat will automatically turn the
unit off. Should this occur, unplug the vacuum
cleaner from the wall outlet and turn off the switch.
Open the unit and check the dust bag. If full, replace.
Wash the foam filter sleeve. Allow the cleaner to cool
for approximately one (1) hour.
To re-start, plug into a wall outlet and switch back on.
3
1. Insert the flexible hose into the inlet on the main
body of the vacuum cleaner. Push in and twist
clockwise a quarter turn until tight (Fig. 4/1).
5. Replace top cover.
4. Position the dust bag to fill the inside of the bin
(Fig 3/4).
3. Fit the dust bag by aligning the front of the dust
bag with the inlet slots (Fig. 3/3).
2. Remove the accessories (Fig. 3/2).
1. Unclip the retainer clips on either side of the
vacuum cleaner and lift off to gain access to the
dust bag compartment. (Fig. 3/3).
3. Initial Set Up
IMPORTANT: The accessories are stored in the dust
bag compartment and need to be removed before
operating the vacuum cleaner.
Fig.3/1
Fig.3/2
Fig.3/3
Fig.3/4
4. Use and Function
IMPORTANT: Always remove the power plug from
the wall outlet before assembling or before removing
accessories.
Fig.4/1
(Fig. 4/2)
4
Initial Set Up/Use and Function
2. Push the two-piece extension tube onto the end
of the handle (Fig. 4/2).
(Fig 4/3)
3. Fit the combination floor tool by pushing on to
the extension tubes (Fig 4/3).
Fig.5/1
Vacuuming Carpets
On/off Button
Fig.5/2
Vacuuming Hard Floors
For hard floor cleaning, press the rocker switch on the
combination floor tool backwards as shown to
(Fig.5/3).
(Fig.5/3)
Cord Wrap
(Fig. 5/4)
Carry Handle
Fig. 5/5
Use and Function/How to Operate
lower the brushes
5
Use the carry handle located on the top of the vacuum
cleaner to move from room to room (Fig. 5/5).
Fully unwind the power cord and plug the cord into
the electrical outlet. Turn the vacuum cleaner on by
depressing the button located on the top of the
carry handle (Fig. 5/1). The vacuum cleaner can be
turned off by pressing the on/off button again.
For carpet cleaning, press the rocker switch
on the combination floor tool forward as
shown to raise the brushes (Fig. 5/2)
After use, turn the vacuum cleaner off and unplug
from the electrical outlet. Wrap the cord around the
top section of the vacuum cleaner and secure in place
with the cord clip (Fig. 5/4).
5. How to Operate
Fig. 7/1
Fig. 7/2
Fig. 7/3
Pre-motor Filter
6. Accessories
Fig. 6/1
Fig. 6/2
Crevice tool : For crevices, corners, cracks etc.
Dusting brush : For delicate surfaces.
Upholstery tool : For carpet, upholstery, stairs etc.
6
Accessories/Dust Bag & Filters: Removal & Replacement
7. Dust Bag & Filters:
Removal & Replacement
IMPORTANT: Always remove the plug from the wall
outlet before assembling or before removing
accessories.
1. The accessories can be attached directly to the
handle by removing the tubes and pushing in the
desired accessory (Fig. 6/1).
1. Turn off the vacuum cleaner and unplug it from the
mains. Remove the hose. Unclip the retainer clips
on either side of the vacuum cleaner and lift off to
gain access to the dust bag compartment
(Fig. 7/1).
2. Lift out the full dust bag (Fig. 7/2).
3. Dispose of the full dust bag and insert a new dust
bag back into the vacuum cleaner aligning the
front of the dust bag with the inlet slots (Fig. 7/3).
1. Turn off the vacuum cleaner and unplug it fron the
mains. Unclip the retainer clips on either side of
the vacuum cleaner and lift off to gain access to
the dust bag compartment (Fig. 7/4).
2. The accessories can also be attached to the
extension tube for extra reach. Remove the
combination floor tool and push on the desired
accessory (Fig.6/2).
IMPORTANT: Always unplug the vacuum cleaner
from the electrical outlet before removing the dust
bag.
IMPORTANT: DO NOT use the vacuum cleaner
without ALL of the filters in place.
Fig. 7/8
Fig. 7/9
Fig. 8/1
7
Dust Bag & Filters: Removal & Replacement/Clearing Blockages
Fig.7/4
Fig. 7/5
Fig. 7/6
2. The pre-motor filter is found on the underside of
the top cover. To release the filter turn the cover
anti-clockwise and lift away (Fig. 7/5).
3. The pre-motor filter is protected by a foam filter
sleeve. This can be washed using cold water,
leaving it to fully air dry before replacing (Fig. 7/6).
4. The HEPA pre-motor filter can be washed using
cold water. Ensure filter is completely dry before
replacing. (Fig. 7/7).
5. The pre-motor filter should be replaced every
9-12 months.
Post-motor Filter
1. Located at the rear of the vacuum cleaner is a
post-motor filter which can also be removed and
replaced.
2. Push in latches on both sides of the cover
to release to post-motor filter (Fig. 7/8).
3. Remove the post-motor filter (Fig. 7/9).
5. The post-motor filter should be replaced every
9-12 months.
4. The filter can be tapped against the side of a
bin to remove debris. It can then be washed
using cold water leaving it to fully air dry before
replacing (Fig. 7/10).
1. Switch the vacuum cleaner off and disconnect
the plug from the electrical outlet.
2. The flexible hose can be disconnected from the
vacuum cleaner by rotating anti-clockwise and
pulling away from the machine (Fig. 8/1). Remove
any blockages found then reconnect the hose
securely.
8. Clearing Blockages
Fig.7/7
24
24
Fig. 7/10
8
Troubleshooting
WARNING: TO REDUCE RISK OF PERSONAL INJURY, UNPLUG THE VACUUM
CLEANER BEFORE SERVICING
9. Troubleshooting
PROBLEM: Cleaner won’t run
Cause: Not properly plugged into electrical outlet.
Solution: Plug in firmly.
PROBLEM: Vacuum cleaner won’t pick up/loss of suction
Cause: Dust bag not installed correctly.
Solution: Review dust bag removal and replacement.
PROBLEM: Accessories won’t pick up
Cause: Accessories not attached correctly.
Solution: Refer to page 6 for fitting information.
PROBLEM: Dust escaping from the vacuum cleaner
Cause: Dust bag full.
Solution: Dispose of dust bag and replace with a new one.
Cause: Dust bag not installed correctly.
Solution: Review dust bag removal and replacement.
Cause: Hose not installed correctly.
Solution: Review hose installation.
Cause: Filter not installed completely.
Solution: Review filter removal and replacement.
Cause: Dust bag full or blocked.
Solution: Replace dust bag.
Cause: Clogged filter.
Solution: Remove filter and clean.
Cause: Blockage in hose.
Solution: Disconnect hose, remove obstruction then re-fit.
Cause: No electricity in electrical outlet.
Solution: Check fuse or breaker.
Cause: On/off switch not turned on.
Solution: Push on/off switch to on.
Cause: Motor thermostat has tripped.
Solution: Switch off and unplug the cleaner. Leave for one (1) hour before switching the cleaner back on.
Cause: Blown fuse/tripped breaker.
Solution: Reset circuit breaker or replace fuse.
9
10. UK Service & Help
(UK) 0844 412 8455
(ROI) 1-800 928 308
11. Technical Specification
Monday-Friday 8.30am to 6.30pm
Saturday-Sunday 9.00am to 5.00pm
If you have any queries about using your carpet cleaner, call the Vax
Careline.
Please make a note of the serial number and model number of the carpet
cleaner before calling. For the nearest Service Agent, please call the Vax
Customer Careline or visit vax.co.uk
Voltage: 220-240V ~50Hz
Wattage: 1200W
Capacity: 10L
Filters: Pre-motor HEPA filter - washable
Foam filter sleeve - washable
Post motor HEPA filter - washable
Cord length: 10m
Weight: 7.6kg
Subject to technical change without notice.
EEC STATEMENT OF COMPLIANCE
Manufacturer/EEC importer: Vax Limited, hereby on our own responsibility declare that the product
V-100T is manufactured in compliance with the following:
Safety: 73/23/EEC Low Voltage Directive, as modified by 93/68/EEC
EMC: 89/336/EEC Electromagnetic Compatibility Directive, as modified by 93/68/EEC
Waste electrical products should not be disposed of with household waste. Please recycle where
facilities exist. Check with your Local Authority or retailer for recycling advice.
Vax Ltd., Kingswood Road, Hampton Lovett, Droitwich, Worcestershire, WR9 OQH, UK
email: info@vax.co.uk - website: vax.co.uk
Loading...