www.vax.co.uk
Please read carefully before using this cleaner.
Always fully extend the mains cable before use.
Retain for future reference.
Vax careline
0870 6061248
instruction manual
Bagless cylinder
Vax model number:
V-091Series
V-091
1. Diagram
www.vax.co.uk
2
parts overview
1
6
13
7
8
2
3
4
5
Fig.1/1
1 Hose inlet
2 On/off button
3 Floor tool parking slot
4 Post-motor filter cover
5 Wheel
6 Cord rewind button
7 Variable power dial
8 Power level indicator
9 Carry handle
10 Quick-release dirt container
button
(located under safety latch)
11 Dirt container release button
12 Dirt container handle
13 Central HEPA filter
9
10
11
12
3
V
ax Careline 0870 606 1248
safety information
1 2 in 1 tool 2 Crevice tool 3 Combination floor tool
TurboBrush
(Model: V-091P, V-091PB, V-091PBA only)
Central HEPA filter (Additional)
TurboBrush
(Model: V-091TB, V-091X only)
Accessories
Fig.1/2
Fig.1/3
Fig.1/4
Fig.1/5
Hard Floor Tool
(V-091P, V-091PB, V-091PBA only)
TurboTool
(V-091P, V-091PB, V-091PBA,
V-091S, V-091PA,
V-091C,V-091FC
only)
Fig.1/6 Fig.1/7
Hose
Fig.1/8
Telescopic Tube X-tend (V-091X only) Stretch Hose (V-091S only)
Fig.1/9 Fig.1/10 Fig.1/11
1 2 3
www.vax.co.uk
4
assembly
2. Safety Information
For Household Use Only
When using the vacuum cleaner, basic safety precautions
should always be observed, including the following:
1. Only use the vacuum cleaner indoors on dry
surfaces.
2. Turn off the vacuum cleaner controls before
connecting or disconnecting from the mains supply.
3. Always unplug the vacuum cleaner before
connecting or disconnecting the vacuum hose and
accessories.
4. Children should be supervised to ensure that they
do not play with the appliance.
5. The appliance is not intended for use by persons
(including children) with reduced physical, sensory or
mental capabilities, or lack of experience and
knowledge, unless they have been given supervision
or instruction concerning use of the appliance by a
person responsible for their safety.
6. Use only as described in this manual.
Use only the manufacturer’s recommended
attachments.
7. Do not use the vacuum cleaner if it has been
dropped, damaged, left outdoors or dropped into
water. Do not use the vacuum cleaner with a
damaged cord or plug. If the supply cord or plug is
damaged, return the vacuum cleaner to a Vax
Authorised Service Agent or suitably qualified
person for examination, repair or adjustment.
8. Do not pull or carry by the cord. Do not use the cord
as a handle, close a door on the cord or pull the cord
around sharp edges or corners. Do not run the
vacuum cleaner over the cord. Keep the cord away
from heated surfaces.
9. Do not handle the plug or vacuum cleaner with wet
hands. Do not use outdoors or on wet surfaces.
10. Do not put any objects into openings. Do not use
with any openings blocked and do not restrict air
flow. Keep all openings free of dust, lint, hair or
anything that may reduce airflow.
11. Keep hair, loose clothing, fingers and all parts of the
body away from openings and moving parts.
12. Do not pick up hot coals, cigarette butts, matches or
any hot, smoking or burning objects.
13. Do not pick up flammable or combustible materials
(lighter fluid, petrol, kerosene, etc) or use in the
presence of explosive liquids or vapours.
14. Do not vacuum up harmful or toxic material (chlorine
bleach, ammonia, drain cleaner, etc).
15. Do not vacuum up hard or sharp objects such as
glass, nails, screws, coins, etc.
16. Do not use without the filters in place.
17. Take extra care when vacuuming on stairs.
18. Keep vacuuming area well lit.
19. Store the vacuum cleaner indoors in a cool, dry area.
20. Turn off the on/off switch before unplugging the
vacuum cleaner.
21. Use only CE-approved 13 amp extension cords. Nonapproved extension cords may overheat. Care should
be taken to arrange the cord so that the cord cannot
be pulled or tripped over.
WARNING: Always switch off and unplug the
vacuum cleaner from the electrical outlet
before assembling, opening or emptying the dirt
container, or before connecting/disconnecting the
attachments.
CAUTION: The vacuum cleaner is a very
powerful unit. Before plugging the cord into
the electrical outlet, make sure the switch is in the
‘off’ position.
IMPORTANT: If the inlet, hose or telescopic
tube is blocked, switch off the vacuum cleaner
and remove the blockage(s) before re-starting the
vacuum cleaner.
IMPORTANT: Cleaning filters improves vacuum
performance. Make sure all the filters are
completely dry before inserting back into the vacuum
cleaner.
This vacuum cleaner is intended for household use only
and not for commercial or industrial use.
!!!
!
Motor Thermostat
IMPORTANT: The motor is equipped with a thermal
cut-out. If for any reason, the vacuum cleaner should
over-heat, the thermostat will automatically turn the
unit off. Should this occur, unplug the vacuum cleaner
from the electrical outlet and turn off the switch.
Remove the dirt container and empty. Clean the
filters. Allow the cleaner to cool for approximately one
(1) hour. To re-start, plug into an electrical outlet and
switch back on.
5
V
ax Careline 0870 606 1248
operation
3. How to Assemble
IMPORTANT: Always unplug the vacuum cleaner
from the electrical outlet before assembling or
removing the accessories.
1. Insert the flexible hose into the inlet on the main body
of the vacuum cleaner. Push in until it clicks into
position (Fig.3/1).
2. Push the telescopic extension tube on to the end of
the handle (Fig.3/2).
3. The telescopic extension tube can be lengthened or
shortened by pushing the button in and sliding the
tube apart or together as required (Fig.3/3).
4. Fit the combination floor head by pushing onto the
extension tube (Fig.3/4).
4. How to Operate
Cord Release
Fully unwind the power cord. A yellow mark on the power
cord indicates the recommended cord length. Do not
exceed the cord length beyond the red mark.
On/Off Button
Insert the power plug into the electrical outlet. Ensure the
vacuum cleaner is switched off.
Press the on/off button located on the top of the vacuum
cleaner and press the button again to turn the vacuum
cleaner off.
Carpet Cleaning
For carpet and rug cleaning press the rocker switch on the
combination floor head to raise the brushes.
(Model: V-091TB, V-091X,
V-091P, V-091PB,
V-091PBA
only): Attach the TurboBrush floor head to the
end of the extension tube. For large carpeted areas only.
(NOTE: not recommended for hard floors)
Hard floor cleaning
For hard floor cleaning, press the rocker switch on the
combination floor head to lower the brushes.
(Model:
V-091P, V-091PB, V-091PBA, V-091S
only):
Attach the hard floor tool head to the end of the extension
tube. For parquet and laminate coverings.
Cord Rewind
To rewind the power cord, press the cord rewind button,
located on the top of the vacuum cleaner, and guide the
power cord with one hand. This will prevent the cord from
whipping which could cause damage or injury.
Variable Power
Located between the cord rewind button and the on/off
button there is a variable power dial. Rotate this clockwise
and anti-clockwise to adjust the suction power, LEDs will
light up dependant on power level.
Carry Handle
Use the carry handle located behind the cord rewind
button and on/off button to move the vacuum cleaner
from room to room.
Hose Storage
For convenience there is a slot located on either side of
the vacuum cleaner where the floor tool and hose can be
parked for carrying and storage.
Fig.3/1
Fig.3/2
Fig.3/3
Fig.3/4
!
www.vax.co.uk
6
accessories / dirt container & filter
5. Accessories
The accessories can be attached directly to the handle by
removing the telescopic tube and pushing in the desired
accessory.
The accessories can also be attached to the telescopic
tube for extra reach. Remove the combination floor head
and push on the desired accessory.
2-in-1 Tool
Dusting brush: for delicate surfaces.
Upholstery tool: for carpet, upholstery, stairs, etc.
Crevice Tool
Use the crevice tool for crevices, corners and cracks, etc.
TurboBrush
(Model: V-091TB, V-091P, V-091PB, V-091PBA,
V-091S only)
For pet hair and larger carpeted areas. (NOTE: Not
recommended for hard floors).
TurboTool
(Model: V-091P, V-091PB, V-091PBA, V-091S,
V-091PA, V-091C, V-091FC only)
For pet hair, stair and upholstery cleaning (NOTE: Do not
use the TurboTool on suede and leather surfaces).
Hard floor tool (Model: V-091P, V-091PB, V-091PBA only)
For hard floor, parquet and laminate coverings.
X-tend
(Model: V-091X only)
For convenient bottom-to-top stair cleaning.
1. The hose fits directly into the hose inlet on the
vacuum cleaner.
2. The handle fits directly on to the telescopic extension
tube.
3. To release the extra length hose, press the release
clips located on the handle.
Stretch hose
(Model: V-091S only)
For full height stair cleaning (NOTE: This should not be
used as the main vacuum hose)
NOTE: For stair cleaning, the unit should always be
placed at the bottom of the stairs.
6. Dirt Container & Filter:
Removal and Replacement
IMPORTANT: The dirt container must be
emptied every time dirt in the container
reaches the MAX mark.
WARNING: Always unplug the vacuum cleaner
from the electrical outlet before removing the
dirt container.
WARNING: Do NOT use the vacuum cleaner
without ALL of the filters in place.
NOTE: For best performance, replace filters annually.
Emptying the Dirt Container
Press the button located on the dirt container handle to
pull out the dirt container (Fig.6/1)
Lift up the safety latch (Fig.6/2)
Press the button located under the safety latch to empty
the dirt into a rubbish bin. When all of the dirt has fallen,
close the dirt container flap, close the safety latch and
replace the dirt container.
Fig.6/1
Fig.6/2
!!!
7
V
ax Careline 0870 606 1248
dirt container & filter / clearing blockages
Cleaning the Filter
IMPORTANT: An extra central HEPA filter has
been included in the carton packaging. Vax
recommends replacing the central HEPA filter every
6-12 months.
Remove the dirt container as directed.
Release the filter safety latch located on top of the dirt
container and pull out the central filter (Fig.6/3).
Gently tap the filter against the side of a rubbish bin to
remove excess dirt.
The central filter can be washed in warm water (max
40°C). Allow to air dry completely before replacing.
NOTE: Do NOT use any detergents or boiling water to
wash the filter. Vax recommends washing the filter
every time you empty the dust container.
Return the central filter to the dirt container ensuring the
filter safety catch has been reset.
Replace the dirt container as directed.
Post-motor Filter
NOTE: This is located on the right hand side of the
vacuum cleaner.
Release the post-motor cover and remove the filter by
pressing in the catch on the left hand side.
Replace the post-motor filter every 9-12 months.
Replace the post-motor filter and cover before re-starting
the vacuum cleaner.
7. Clearing Blockages
WARNING: To reduce the risk of electric shock,
the power cord must be disconnected before
performing maintenance or troubleshooting checks.
Turn the vacuum cleaner off and unplug from the electrical
outlet.
The flexible hose, stretch hose (Model:V-091S only) and
X-tend (Model: V-091X only) can be disconnected from the
vacuum cleaner by pushing in the button on the hose and
pulling away from the machine. Remove any blockages
found then re-connect the hose securely.
Removing debris from the TurboTool
(Model: V-091P,
V-091PB, V-091PBA, V-091S, V-091PA V-091FC only)
Switch the vacuum cleaner off and disconnect the power
plug from the electrical outlet.
Rotate the locking ring 180º (Fig.7/1).
Lift the top cover off and remove any blockage (Fig.7/2).
To re-assemble, ensure that the tabs are engage. Pivot the
lower housing closed and rotate the locking ring 180º
(Fig.7/2).
Fig.6/3
LOCKING RING
Fig.7/1
TABS
Fig.7/2
!
!
www.vax.co.uk
8
clearing blockages/ storage
Removing debris from the TurboBrush (
Model: V-091P,
V-091PB, V-091PBA, V-091X, V-091TB only)
The brushbar will stop rotating if it is blocked during
operation by vacuuming up foreign objects, or is strands of
carpet are wrapped around it.
Switch the vacuum cleaner off and disconnect the power
plug from the electrical outlet.
Lay the TurboBrush floor head on a flat surface and turn
over to expose the brushbar. Using a pair of scissors, cut
through any threads or hairs caught by the brushbar that
have wrapped around the guides (Fig.7/3).
NOTE: The brushbar will also stop rotating if the
central filter is clogged.
8. Storage
IMPORTANT: Always unplug the vacuum cleaner
from the electrical outlet and rewind the power
cord as directed before storing.
NOTE: Always store the vacuum cleaner base down.
!
Fig.7/3
9. Troubleshooting
WARNING: To reduce the risk of personal injury,
unplug the vacuum cleaner before performing
maintenance or troubleshooting checks.
PROBLEM: Vacuum cleaner won't run
Cause: Not properly plugged into electrical outlet.
Solution: Plug in securely.
Cause: No electricity in the electrical outlet.
Solution: Check fuse or breaker.
Cause: On/off switch not turned on.
Solution: Push on/off switch to ‘on’.
Cause: Motor thermostat has tripped.
Solution: Switch off and unplug the vacuum cleaner.
Leave for one (1) hour before switching the
vacuum cleaner back on.
Cause: Blown fuse/tripped breaker.
Solution: Reset circuit breaker or replace fuse.
PROBLEM: Cleaner won’t pick up/loss of suction.
Cause: Dirt container not installed properly.
Solution: Review dirt container replacement.
Cause: Dirt container full or blocked.
Solution: Empty dirt container.
Cause: Clogged filters.
Solution: Remove, clean and replace filters.
PROBLEM: Accessories won’t pick up.
Cause: Accessories are not attached correctly.
Solution: Refer to section 5.
Cause: TurboBrush / TurboTool is clogged.
Solution: Refer to section 7.
Cause: Hose / Stretch Hose (Model: V-091S only) /
X-Tend (Model: V-091X only) is not installed
correctly.
Solution: Refer to section 7.
PROBLEM: Dust escaping from the vacuum cleaner.
Cause: Dirt container full.
Solution: Empty dirt container.
Cause: Dirt container not installed correctly.
Solution: Review dirt container replacement.
Cause: Hose / Stretch Hose (Model: V-091S only) /
X-Tend (Model: V-091X only) is not installed
correctly.
Solution: Review installation.
Cause: Filter not installed completely.
Solution: Remove, clean and replace filters.
9
V
ax Careline 0870 606 1248
troubleshooting
!
www.vax.co.uk
10
10. UK Service & Help
Vax Care 0870 6061248
Monday-Friday 8.00am to 8.00pm
Saturday-Sunday 9.00am to 5.00pm.
Any queries or concerns about using the Vax, call the Vax
Careline. Calls are charged at the UK national rate.
Please make a note of the serial number and model
number of the carpet cleaner before calling. There are
over 400 approved Vax Service Agents in the UK. For the
nearest Service Agent, please call the Vax Careline.
www.vax.co.uk
11. Technical Specification
Voltage: 220-240V ~50Hz
Wattage: 2200W-2400W (dependant on model)
Capacity: 3 litres approx
Filters: Washable central HEPA filter
Post-motor filter
Cord length: 6m approx
Weight: 7.5kg
Subject to technical change without notice.
uk service & help/ technical specification
11
V
ax Careline 0870 606 1248
This page has been left intentionally blank
EEC STATEMENT OF COMPLIANCE
Manufacturer/EEC importer: Vax Limited, hereby on our own responsibility, declare that the
V-091 Performance Cylinder range is manufactured in compliance with the following Directives:
Safety: 2006/95/EC Low Voltage Directive
EMC: 2004/108/EC Electromagnetic Compatibility Directive
Waste electrical products should not be disposed of with household waste. Please recycle where
facilities exist. Check with your Local Authority or retailer for recycling advice.
Vax Ltd., Kingswood Road, Hampton Lovett, Droitwich, Worcestershire, WR9 OQH, UK
email: info@vax.co.uk - website: www.vax.co.uk
Loading...