vax.co.uk
Please read carefully before using this cleaner.
Always fully extend the mains cable before use.
Retain for future reference.
Vax Careline: (UK) 0844 412 8455
(ROI) 1-800 928 308
instruction manual
Steam cleaner
Vax model number:
V-085 Series
Version 1.0
1. Diagram
vax.co.uk
2
parts overview
5
4
3
2
13
12
11
10
10
6
7
8
9
19
14
15
16
17
18
23
1
20
24
21
22
25
28
27
26
1 Accessory storage
2 Power indicator light (red)
3 Steam ready light (yellow)
4 On/off switch
5 Carry handle
6 Tank safety cover
7 Tool parking slot
8 Power cable
9 Wheel
10 Hose
11 Steam gun
12 Connection nozzle
13 Steam switch
14 Lock (child safety)
15 Accessory attachment button
16 Extension tubes
17 Release button
18 Floor nozzle
19 Cloth holder
20 Large cloth
21 Accessory adaptor
22 Concentration nozzle
23 Jet nozzle attachment
24 Round brush (plastic bristles)
25 Round brush (metal bristles)
26 2-in-1 combi-attachment -
Rectangular steam nozzle and window
attachment
27 Cotton cover
28 Measuring jug
3
safety information
2. Safety Information
FOR HOUSEHOLD USE ONLY.
When using the steam cleaner, basic safety
precautions should always be observed,
including the following:
1. Do not leave the steam cleaner unattended when
plugged in. Unplug it from socket when not in use.
2. To prevent electric shock do not use outdoors.
3. Not to be used as a toy. Close supervision is
necessary when used near children or the infirm.
4. Use only as described in this manual.
5. Do not use the vacuum cleaner if it has been
dropped, damaged, left outdoors or dropped into
water. Do not use the vacuum cleaner with a
damaged cord or plug. If the supply cord is
damaged, it must be replaced by the manufacturer
or a recommended Service Agent to avoid hazard
and invalidating the guarantee.
6. Do not pull or carry by the cord, use the cord as a
handle, allow the cord to come into contact with hot
or sharp surfaces or close a door on the cord.
7. Do not unplug by pulling on the cord.
8. Do not handle the plug or steam cleaner with wet
hands.
9. Do not put any objects into openings or operate
with openings blocked.
10. Do not use without the tank cap in place.
11. Turn off all controls before unplugging.
12. Keep the steam cleaner on the floor.
13. Do not use an extension cord.
14. Do not attempt to remove blockages with sharp
objects as they may cause damage.
15. Store indoors, put away after use to prevent tripping
accidents.
16. Using improper voltage may result in damage to the
steam cleaner and possible injury to the user. The
correct voltage is listed on the rating label.
17. This steam cleaner is intended for household use
only.
18. A hazard may occur if the steam cleaner runs over
the power supply cord.
19. The steam cleaner must be kept level during
operation.
20. Never immerse the steam cleaner in water or other
liquids.
21. Keep the steam cleaner away from rain and
moisture. The steam cleaner is not suitable for
outdoor use.
22. Do not operate the steam cleaner without water in
the tank. Always top up with water in good time.
23. Empty the water tank when the steam cleaner is
not in use.
24. Never fill the tank with anything other than water.
Never put additives (such as perfume, stain remover
or products containing alcohol) in the water as they
may damage the steam cleaner or make it
dangerous to use.
25. Always remove the mains plug from the socket and
allow this steam cleaner to cool down completely
before topping up with water.
26. Do not over fill the tank. Do not exceed the
maximum prescribed filling level. Please use the
measuring jug and funnel included.
27. Ensure that the water tank’s closure cap has been
screwed down fully before use.
28. Only carry the steam cleaner by the carry handle.
29. Do not touch any hot areas on the steam cleaner. It
is normal for the steam cleaner to heat up during
operation.
30. Do not use the steam cleaner to treat any items of
clothing that are still being worn on the body.
31. The force and heat of the steam may have an
adverse effect on some materials. Always check
whether a surface is suitable for treatment with the
steam cleaner by carrying out a test beforehand on
a concealed area.
32. Always include these operating instructions if
passing the steam cleaner on to a third party.
33. Never aim the steam cleaner at people, animals or
plants (risk of scalding)! Do not aim the steam
cleaner at electrical systems or wires.
34. Do not operate the steam cleaner without
supervision. Please always switch the appliance off
and remove the mains plug from the socket if
leaving the work area.
35. The steam cleaner is fitted with a thermostat and a
thermal cut-out as protection against overheating.
36. Accessories become hot during use - allow them to
cool down before handling.
37. Please ensure all parts are correctly fitted before
using the product.
38. Do not use your steam cleaner if damaged/ faulty.
Please call our Vax Careline on 0844 412 8455.
PLEASE KEEP THESE INSTRUCTIONS
FOR FURTHER USE.
Vax Careline: (UK) 0844 412 8455
(
ROI) 1-800 928 308
!
4
assembly
3. Assembly
Extension tubes
To choose the correct length for the task, you can fit one
or two of the extension tubes.
Push the extension tube onto the connection nozzle as
far as it will go until you hear it click into place. Then fit
the floor nozzle.
WARNING: Remove the plug from the socket
before fitting or changing accessories The
accessories will become hot during use - allow them to
cool down before replacement.
Accessory adaptor
Push the accessory adaptor as far as it will go onto the
connection nozzle of the steam gun until you hear a click.
The accessory adaptor can be removed again by pressing
the accessory connection button and pullling the adaptor
off. Allow to cool before removing.
Concentration nozzle
The concentration nozzle is pushed directly onto the
accessory adaptor until it clicks into place. It can be used
with various fittings (jet nozzle attachment, brush
attachment, 2-in-1 combi-nozzle) depending on the task.
Jet nozzle attachment
The jet nozzle attachment can be fitted directly to the
concentration nozzle. Push and twist to fit.
Ideal for hard to reach places such as corners and joints.
Brush attachments
Ideal for removing stubborn dirt from surfaces, the brush
attachments can be fitted directly to the concentration
nozzle. Push and twist to fit.
2-in-1 combi-attachment
Rectangular steam nozzle
- the hand nozzle can be fitted
directly to the concentration nozzle. Push and twist to fit.
The rectangular steam nozzle can be used either with or
without the cotton cover, depending on cleaning
requirements.
Ideal for cleaning kitchen work surfaces. Add cotton cover
for extra protection.
!
!
vax.co.uk
2
1
5
operation / accessories
Window attachment - Push the window attachment
onto the rectangular steam nozzle until you hear it click
into place. You can fit the window attachment to the
concentration nozzle by pushing it into place.
Perfect for cleaning windows, mirrors, ceramic tiles and
surfaces and other non-porous, smooth surfaces.
Apply the steam evenly to the glass surface from a
distance of about 20cm. Switch the steam off and wipe
the moisture off the glass top to bottom in strips using
the rubber squeegee. Wipe the rubber squeegee and the
lower edge of the window dry after every strip.
WARNING: Glass surfaces can be shattered by the
sudden application of excessive heat. Before
cleaning such glass surfaces with the steam
cleaner. warm them up by applying steam to the surface
from a distance of 20-25cm. Continue by applying steam
from a distance of 10-15cm.
4. How to Operate
Over-heating protection
The steamer is equipped with protection against overheating. The cleaner will switch itself off automatically
on reaching a temperature of 180˚C, in order to prevent
over-heating. In this event, please remove the plug from
the socket immediately. Allow the cleaner to cool down
for 30 minutes before resuming work.
Filling the water tank
Always ensure that the plug of the steamer is removed
from the socket before filling or refilling the cleaner with
water. Remove the cover of the water tank by pressing it
down and turning it anti-clockwise. Fill the tank with 1.4L
of water using the measuring beaker. Replace the cover
and close it tightly by turning in the clockwise direction.
The water tank should be emptied after use. Allow the
inside of the water tank to dry out before replacing the
cover.
If the water tank needs to be refilled during use, first
switch the cleaner off and remove the plug from the
socket. Before opening the tank cover to refill the tank,
release the steam switch on the steam gun or allow the
cleaner to cool down completely.
WARNING: Even after a cooling period of 5
minutes, the remaining water in the tank and the
tank cover locking screw will still be hot. Always take care
when removing the tank cover locking screw, since hot
steam may be emitted and the thread can still cause
burns. The filler opening of the cleaner must never be
opened during use (CONTAINER UNDER PRESSURE).
WARNING: Never fill the tank with anything but
cold water. The use of any other fluids can be
dangerous, and can lead to damage of the heating
element.
Vax Careline: (UK) 0844 412 8455
(
ROI) 1-800 928 308
!
!!!!!
water
6
accessories / dirt container & filter
Power indicator light / On/off switch
When the water tank has been filled, insert the plug into
the socket. Switch the cleaner on by pressing the on/off
switch to on. The power indicator light (red) should then
come on, indicating that the cleaner is being supplied
with power.
Ready display
The steam ready light (yellow) will come on, indicating
that the steam cleaner is ready to use. The operating
temperature will be reached after about 11 minutes
(steam ready light (yellow) goes out). The steamer is now
ready for use.
WARNING: In order to avoid injury, the steam
should be switched off during breaks or pauses
during work by pressing the on/off switch to off.
If you leave the working area, please switch the cleaner
off and remove the plug from the socket (by pulling on
the plug, and not on the power supply cable).
Steam gun
The cleaner is ready for use when the yellow steam ready
light goes out. Ensure that the child safety lock on the
steam gun is off. When the steam switch is pressed,
steam will be emitted from the nozzle. Direct the steam
gun at a cloth first, until the steam is emitted evenly.
Keep the steam switch depressed, and direct the steam
jet at the surface to be cleaned, removing the dirt by
moving the steam jet to and fro over the surface. The
steam jet will stop as soon as the steam switch is
released.
NOTE: When the lock is pushed to the forward position,
the steam switch cannot be pressed. Push the lock to the
rear position to release the steam switch.
NOTE: In order to ensure safe use, even in the case of
accidental contact with liquids, the steam gun is insulated
from the electrical power supply (zero volt system).
WARNING: When cleaning surfaces with the
steam gun, wipe the surface dry afterward using a
micro-fibre or cotton cloth if necessary; this will also
remove any excess moisture for thorough cleaning. In
order to control the steam temperature and cleaning
power at the surface, move the steam gun closer to or
further away from the surface.
After use
WARNING: Before opening the tank cover to
empty the tank, release the steam pressure by
pressing the steam switch on the steam gun, or allow the
cleaner to cool down completely.
Switch the cleaner off and remove the plug from the
socket. Wait until the cleaner has cooled down
completely. Empty the water tank. Allow the inside of the
water tank to dry out before replacing the cover. Store
the steamer in a dry area safely out of the reach of
children.
Rinsing out the water tank
To clean the water tank, we recommend that you fill it
with water and shake vigourously. This will release any
limescale desposits that have collected on the bottom of
the tank. Pour the water out while holding the cleaner
upside down to rinse out any limescale deposits. In hard
water areas it is recommended to use distilled/bottled
water to avoid limescale deposits.
5. Cleaning and Maintenance
Cleaning and maintenance work on the cleaner must only
be carried out when the plug has been removed from the
socket.
Allow the cleaner to cool down completely before putting
it away or carrying out any cleaning.
Clean the steam cleaner and accessories only with a
slightly damp cloth.
NOTE:
In order to prolong the working life of the cleaner,
you should descale the steam tank about every 6
months. Switch the cleaner off, remove the plug from the
socket and empty the remaining water as described
above.
Fill the tank with 1L of warm water at about 50˚C and
add 1 or 2 descaling tablets to the tank. Leave the
tablets to work for about 30 minutes, and then empty
the tank of the water and limescale deposits. This
procedure can be repeated if required.
!
!
vax.co.uk
!!!
!
7
belt & brush replacement / clearing blockages
6. Troubleshooting
WARNING: To reduce the risk of personal
injury, unplug the steam cleaner before
performing maintenance or troubleshooting checks.
PROBLEM: Operating pilot lamp fails to light.
Cause: The steam cleaner is not plugged into a socket
or is not switched on .
Solution: Insert the mains plug into a socket or switch
the steam cleaner on.
Cause: The socket is faulty.
Solution: Check the socket by unplugging the steam
cleaner and plugging in a different appliance.
Cause: The power cable is damaged.
Solution: Have the cable replaced by a Vax Service
Agent.
PROBLEM: No steam is emitted when the steam
button is pressed.
Cause: The childproof lock is preventing the release of
the steam button.
Solution: Push the pin on the right-hand side of the
steam gun inwards and to the left.
Cause: The water tank is empty.
Solution: Top up with water.
PROBLEM: Only a very small amount of steam flows
out.
Cause: The steam controller is set to minimum.
Solution: Turn the steam controller anticlockwise until
sufficient steam is emitted.
PROBLEM: The steam cleaner takes a very long time
to heat up.
Cause: The water tank is furred up.
Solution: Descale the water tank.
7. UK Service & Help
Vax Careline:
(UK) 0844 412 8455
(ROI) 1-800 928 308
Monday-Friday 8.30am to 6.30pm
Saturday-Sunday 9.00am to 5.00pm
Any queries or concerns about using your Vax, call the
Vax Careline. Calls are charged at the UK national rate.
Please make a note of the serial number and model
number of the carpet cleaner before calling. For the
nearest Service Agent, please call the Vax Careline or
visit vax.co.uk.
8. Technical Specification
Voltage: 220-240V ~50Hz
Wattage: 1600W
Steam pressure: 3.5bar (max.)
Capacity: 1.4L (max.)
Weight: 4.5kg (without accessories)
Subject to technical change without notice.
!
!
Vax Careline: (UK) 0844 412 8455
(
ROI) 1-800 928 308
EEC STATEMENT OF COMPLIANCE
Manufacturer/EEC importer: Vax Limited, hereby on our own responsibility, declare that the
V-085 Series is manufactured in compliance with the following Directives:
Safety: 2006/95/EC Low Voltage Directive
EMC: 2004/108/EC Electromagnetic Compatibility Directive
Waste electrical products should not be disposed of with household waste. Please recycle where
facilities exist. Check with your Local Authority or retailer for recycling advice.
Vax Ltd., Kingswood Road, Hampton Lovett, Droitwich, Worcestershire, WR9 OQH, UK
email: info@vax.co.uk - website:vax.co.uk
Loading...