Visit our website at oreck.co.uk or email us at info@oreck.co.uk.
PLEASE DO NOT RETURN THIS PRODUCT TO THE STORE.
4
IMPORTANT SAFETY INSTRUCTIONS
SAVE THESE INSTRUCTIONS
When using an electrical appliance, basic precautions should always be followed, including
the following: READ ALL INSTRUCTIONS BEFORE USING THIS APPLIANCE.
WARNING: TO REDUCE THE RISK OF FIRE,
ELECTRIC SHOCK OR INJURY:
This air purifier is intended for household use only and NOT for commercial or industrial use.
• Only use the air purifier indoors and keep away from wet areas.
• Keep fingers, hair and loose clothing away from moving parts and openings whilst
using the air purifier.
• This appliance can be used by children aged from 8 years and above and persons
with reduced physical, sensory or mental capabilities or lack of experience and
knowledge if they have been given supervision or instruction concerning use of the
appliance in a safe way and understand the hazards involved. Children shall not play
with the appliance. Cleaning and user maintenance shall not be made by children
without supervision.
• Always position the air purifier on a flat, stable, solid surface and never over stretch
the power cord.
• Position the air purifier where dirty air is not drawn across your body or head while
sitting or sleeping.
• Don’t place air purifier near sources of heat, such as stove tops, ovens, radiators
or computers.
• Don’t use the air purifier if the power cord or plug is damaged. Please contact our
Customer Care Line.
• Don’t use the air purifier if it has been dropped, damaged or left outdoors.
• Don’t run the power cord under rugs, runners or carpets as it can be a trip hazard.
• Don’t pull, carry or trap the power cord under doors or sharp edges.
• Don’t handle the plug or air purifier with wet hands.
• Don’t unplug the air purifier by pulling on the power cord.
• Don’t use the air purifier in an area with toxic/explosive vapours/liquids, oxygen tanks
or near to flammable, combustible materials (lighter fluid, petrol, kerosene, chlorine,
bleach and ammonia drain cleaner etc).
• Don’t use the air purifier with incorrect voltage as this may result in damage or injury
to the user. The correct voltage is listed on the ratings label.
• Don’t use without all filters in place.
• Inspect the air purifier regularly and remove any dust/dirt build up as this may
affect the airflow.
• Keep all openings/grills clear and free from obstruction and sources of heat, open
flames including candles. Don’t attempt to remove blockages with sharp objects as
this may cause damage to the air purifier.
• Turn off all controls on the air purifier before disconnecting or connecting the
power cord.
• Always replace the fuse in the plug with a 5amp fuse. Always protect the power
cable from heat.
• Use only CE approved 5amp extension cords, non-approved extension cords
may overheat.
• Care should be taken to arrange the extension cord as it can be trip hazard.
• Always switch off and unplug the air purifier before performing maintenance
or troubleshooting checks.
PLEASE KEEP INSTRUCTIONS FOR FURTHER USE.
5
TECHNICAL SPECIFICATIONS
AIR16UK
Wattage
Weight
Noise Level
40W
7. 2kg
37dB(A)
6
CARTON CONTENTS
2. FEATURES
A
Pre-Filter
Filters large particles such as dust, hair and lint.
B
Cleaning Brush
Use to clean the front and back grills. Stores snuggly in the
compartment under the cover.
C
Odour Absorber
This component combines advanced catalytic technologies to
reduce odors and chemical fumes from glues, solvents, and
synthetic materials when air passes through the filter and is
activated by the DualMax® internal lights. (The Odour Absorber
System cannot be removed.)
D
Truman Cell
®
Electrostatically charges and collects small particles such as dust,
smoke, pollen and mold from the air that passes through the filter.
E
Exhaust Grill
Directs the flow of air as it exits the unit.
F
Power Cord
Plug into the outlet to begin use.
G
Night Light
The Oreck logo on the front panel & the indicators on the control
panel will illuminate when the night light is activated.
H
Collector Cell Light
A solid amber light is included as a handy reminder to clean the
Truman Cell after 30 days. A blinking light indicates a malfunction
that has caused the Truman Cell® to shut down and requires attention.
I
Speed Indicator Light
The speeds will be cumulatively indicated: 1= low; 1+2 = medium;
1+2+3 = high.
J
Odour Absorber Button
This button turns the internal lights on or off as desired. If
turned off, the unit will continue to filter particles from the air
that passes through the filter but its odor and VOC capability
will be greatly reduced.
7
TRUMAN CELL
I
K
H
J
L
M
B
C
E
D
F
K
L
M
G
A
Motor Speed/Power Button
Press the power buttons repeatedly for the desired speed.
• Low for Silence Technology®
• Medium for normal use
• High for maximum cleaning
Night Light Button
Repeatedly press this button to change the lighting scheme to best suit your preference.
Front Grill
Air enters here for the first stage of cleaning.
Remove all parts from carton and identify each item shown.
Make sure all parts are located before disposing of packing materials.
8
TRUMAN CELL
3. OPERATION
PLACE
1. Locate the air purifier on a hard surface such as a table or desk. Be sure the grille is not blocked by
other objects and there are no flames near the unit.
PLUG IN
2. Plug into the nearest standard electrical outlet that accepts a polarized plug.
SELECT
3. Press the motor speed/power button until you reach the desired air cleaning speed.
3
2
1
4. CLEANING
!
WARNING!
Cleaning the unit while it is plugged in may result in electric shock, electric
spark and serious injury. Unplug the unit before cleaning or maintenance.
CLEANING INTERVALS
1. Proper care and cleaning of the air purifier is critical to performance. The following chart shows
the cleaning intervals and method.
PARTCLEANING TIMEMETHOD
CABINETAS NEEDEDWIPE WITH DAMP CLOTH FIRST. IF
REQUIRED, FOLLOW WITH MILD,
NON-ABRASIVE CLEANER.
TRUMAN CELL2 TO 4 WEEKSSPRAY ORECK ASSAIL-A-CELL® CLEANER
OR SOAK IN WARM WATER OR WARM
WATER WITH MILD LIQUID DETERGENT.
RINSE AND DRY THOROUGHLY.
PRE-FILTER2 TO 4 WEEKSRINSE THOROUGHLY IN WARM WATER
OR AS NEEDED.
AIR DIRECTION GRILLAS NEEDEDUSE THE BRUSH PROVIDED WITH THE
AIR PURIFIER TO BRUSH AWAY DEBRIS
IN BETWEEN THE SLOTS.
9
10
CLEANING THE PRE-FILTER
2
3
1. Unplug the air purifier.
2. Open the Cover by gently pulling from the top corners.
3. Pull the Pre-Filter straight out of the Cabinet.
4. Thoroughly rinse the Pre-Filter and let it air dry before placing it back in the Cabinet. Do
not use heated or compressed air as part of the drying process.
5. Slide the Pre-Filter back into the unit.
6. Close the Cover securely.
CLEANING THE TRUMAN COLLECTOR CELL
Note: The Truman Cell® may require more frequent cleaning
if “arcing” occurs. Arcing is a sharp snapping sound that
occurs when large particles are collected in the Truman Cell
If prolonged or continuous arcing occurs the Truman Cell
®
.
®
should be cleaned.
1. Unplug the air purifier.
1
1
2. Open the Cover by gently pulling from the top corners.
3. Remove the Truman Cell®® by unlocking top and
bottom knobs and pulling straight out.
4. Separate the Truman Cell®® from the Wire Assembly
for easier access to each during cleaning.
3
11
WIRE ASSEMBLY
RECESSED
CHANNEL
TRUMAN CELL
5. Place each in sink, bathtub or other location where cleaner can cover every surface.
6. Spray Oreck Assail-a-Cell®® cleaner between each Cell Plate and cover each surface. Allow
the cleaner to soak for a few minutes but do not let it dry. Thoroughly rinse the Truman
Cell®® with clean water.
An alternative method to clean the Truman Cell®® is to rinse or soak it in warm water for
loose debris. Mild liquid dish detergent in water may also be used to help break down
tough dirt and residue. Thoroughly rinse the Truman Cell®® with clean water.
POST
Note: To prevent damage to the components of the Truman Cell®, do not put in dishwasher or use a cotton swab.
Tough residue such as tar from tobacco smoke may need additional cleaning or longer soaking.
7. Shake excess water from the Truman Cell®® to speed up drying time. Do not use heated or
compressed air to dry.
8. Reassemble the Wire Assembly and Truman Cell®® by inserting the post located on the outside
edges of the Wire Assembly into the recessed channels of the Truman Cell®®. After guiding the
post into the recessed channels, slide the Wire Assembly until it locks into place.
9. Place the Truman Cell®® back into the unit by sliding it straight in and turning each knob to its locking
position. The Truman Cell®® is specially designed so that it can only be inserted in one direction.
10. Close the Cover securely.
12
DRYING THE TRUMAN CELL
Note: The Truman Cell® must be completely dry after cleaning to operate properly. A drying
mode is available to help remove any residual moisture. While in this mode, the fan will be
running on Medium speed and no power will be supplied to the Truman Cell
detects that the Truman Cell
®
is completely dry, it will return to its original operating settings
®
. Once the unit
and function as normal.
"DRY MODE" OPERATION
If the power supply detects that the Truman Cell®® is wet, it shuts down power to the cell and causes
the Collector Cell light to blink rapidly.
1. While the collector cell light is blinking, press and hold the power button to initiate “Dry Mode”
2. Next, the following will all happen simultaneously:
• The lights directly above and below the power button will flash 3 times.
• The unit will switch to medium speed.
• The Collector Cell light will start to blink in a slow pattern.
4. Once in “Dry Mode”
• The unit will run for 60 minutes and then attempt to reset the power supply to the Truman Cell®.
• If the power supply successfully restarts, the unit will return to its original speed and run as normal.
• If not successful, it will go through the same process up to two more times.
• If still not successful after the third try, the cell is likely damaged or is shorting out due to the
presence of a foreign object; it will return to the original speed and the Collector Cell light will
blink with a rapid blink pattern indefinitely until the unit is reset.
CLEANING THE EXHAUST GRILL
1
13
2
1. Remove the Cleaning Brush from the storage slot located under the Cover.
2. Brush away debris that has collected between the Grill Slots.
3. Return the Cleaning Brush to the storage slot.
14
5. TROUBLESHOOTING
Service problems that appear to be major can often be solved easily. This guide can help you
troubleshoot.
For any other service problems, contact our customer service team at 0845 603 0153.
PROBLEMCHECKSOLUTION
UNIT DOES NOT
TURN ON
TRUMAN CELL
LIGHT HAS TURNED
SOLID AMBER.
TRUMAN CELL
LIGHT IS
BLINKING AMBER
UNIT DOES
NOT REMOVE
POLLUTANTS.
UNIT SPARKS,
CRACKLES
AND POPS.
UNIT STILL DOES
NOT OPERATE
PROPERLY
• POWER CORD
• SELECTOR SWITCH
• COVER
TRUMAN CELL
TRUMAN CELL
TRUMAN CELL
TRUMAN CELL
®
®
®
®
REVIEW ALL OF
THE ABOVE
• PLUG IN POWER CORD
• SET SELECTOR SWITCH FOR DESIRED FAN SPEED.
• MAKE SURE THE TOP COVER IS SECURELY CLOSED
A SOLID AMBER LIGHT IS A 30 DAY CLEANING
REMINDER. WASH COLLECTOR CELL. MAKE
SURE IT IS THOROUGHLY CLEAN AND DRY
BEFORE REINSTALLING.
• A FAST BLINKING LIGHT INDICATES THE POWER
SUPPLY HAS SHUT DOWN DUE TO ARCING OR
SHORT CIRCUIT. THE CELL SHOULD BE INSPECTED
AND CLEANED, REPAIRED, OR REPLACED.
• A SLOW BLINKING LIGHT INDICATES THE UNIT
IS IN DRY MODE.
• CLEAN THE TRUMAN CELL® AND MAKE SURE IT
IS COMPLETELY DRY BEFORE REINSTALLING.
• TRUMAN CELL® MAY BE DAMAGED. CONTACT
ORECK CUSTOMER SERVICE AT 0845 603 0153.
• SPARKING OR POPPING NOISE (ARCING) CAN
OCCUR WHEN A LARGE PARTICLE IS CAPTURED
IN THE TRUMAN CELL®. IF THE UNIT IS ARCING
EXCESSIVELY, THE CELL MAY BE DIRTY. TRY
CLEANING THE TRUMAN CELL®.
• IF EXCESSIVE ARCING CONTINUES AFTER
PROPER CLEANING, THE TRUMAN CELL® MAY
BE DAMAGED OR WET. IF DAMAGED, CONTACT
ORECK FOR SERVICE.
CONTACT ORECK CUSTOMER SERVICE AT
0845 603 0153.
6. WARRANTY
Oreck MANUFACTURING COMPANY: (Oreck Manufacturing Company gives you the following
limited warranty for this product only if it was originally purchased for residential use, not for resale,
from Oreck or an Oreck Authorized Retail Dealer.)
Oreck will repair or replace, free of charge, to the original purchaser, any part that is found to be
defective in material or workmanship within two (2) years following the date of purchase for all
residential models. NOTE: If the unit is used commercially, a one (1) year overall warranty applies.
This limited warranty does not cover the replacement of expendable or consumable parts such as
filters, cartridges, and other parts subject to normal wear unless they are defective in material or
workmanship.
This limited warranty does not apply to any part subjected to accident, abuse, commercial use,
alteration, misuse, damage caused by an act of God, the use of voltages other than on the data plate
of this product or service of this product by other than Oreck or a participating Factory Authorized
Service Center.
Oreck does not authorize any person or representative to assume or grant any other warranty
obligation with the sale of this product.
Oreck’s limited warranty is valid only if you retain proof of purchase from Oreck or an Oreck
Authorized Retail Dealer for this product. If you purchase this product from any other source, your
purchase is “AS IS,” which means Oreck grants you no warranty, and that you, not Oreck, assume
the entire risk of the quality and performance of this product, including the entire cost of any
necessary servicing or repairs of any defects.
15
Oreck’s liability for damages to you for any costs whatsoever arising out of this statement of limited
warranty shall be limited to the amount paid for this product at the time of original purchase, and
Oreck shall not be liable for any direct, indirect, consequential or incidental damages arising out of
the use or inability to use this product. Some states do not allow the exclusion or limitation of
incidental or consequential damages, so the above limitation or exclusion may not apply to you.
ALL EXPRESS AND IMPLIED WARRANTIES OTHER THAN THE LIMITED WARRANTY SET FORTH
ABOVE, FOR THIS PRODUCT, INCLUDING IMPLIED WARRANTIES OF MERCHANTABILITY AND
FITNESS FOR A PARTICULAR PURPOSE ARE EXPRESSLY DENIED.
This warranty gives you specific legal rights, and you may also have other rights which vary from
state to state.
Quillgol d House, Kingswood Road, Hampton Lovett, Droit wich, Worcs. WR9 0Q H
EEC Statement o f Compliance: Manufac turer/EEC importer : Oreck Ltd., hereby on our own
responsib ility, declare that the AIR16UK series is manufac tured in compliance with the following
Directives: Safety: 2006/95/EC Low Volta ge Directive. EMC: 20 04/108/EC Electromagnetic
Compatibility Directive.
Waste elec trical product s should not be disposed of with household waste. Please recycle
where facilities exist . Check with your Local Au thority or retail er for recycling advice.
AIR 16UK #1-1-13432 2-0 0
Loading...
+ hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.