CLICK HERE FOR ACCESS
Table of Contents
Introduction / Warnings 01 / 02
Battery Installation 03
Charging the Battery 04
Battery Maintenance 05
Master Code Programming 06
Product Registration 07
Biometrics / Programming 08 / 11
Helpful Programming Tips 08
Programming 1st and 2nd Fingerprints 09
Programming Additional Fingerprints 10
Deleting Fingerprints 11
Hot Keys 11 / 12
Tamper Detection 11
Stealth Mode 11
Travel Mode 11
View Battery Status 12
Delete Fingerprints 12
Toggle Interior Light ON/OFF 12
Vaultek™ App 13 / 14
Securing Your Safe 15
Customer Support / Warranty 16
FAQ 17 / 18
Box Contents
VT20i Vaultek™ Safe
18650 Rechargeable Lithium-ion Battery
AC Power Adapter and Micro-USB Charging Cable
High Strength Steel Security Cable
Hardware Mounting Kit
Owner's Manual / Quick Start Guide
Backup Keys (2)
Phillips Head Screwdriver
Installing Your Battery
How to Register Your Safe
Change Your Master Pin Code
How to Program Your Fingerprint
Overview of the Bluetooth App
How to Anchor Your Safe
Hot Keys Available
More videos online.
Vaultek™ App!
The Vaultek™ app is available for Android and iOS devices. The app allows you to remotely unlock safe, check
battery level, toggle sound ON/OFF, adjust the interior light, name ngerprint IDs, plus much more. See pages 13
to 14 for more information.
How-To-Videos
HOW-TO-VIDEOS AVAILABLE CLICK HERE FOR ACCESS
Introduction
The Vaultek™ VT20i is a biometric, PIN access / Bluetooth access safe. Its solid structure and penetration resistant
design makes it ideal for storing valuables such as rearms, jewelry, cash and other personal items. Powered by a
rechargeable lithium-ion battery, the VT20i combines high security with complete access control.
Secure Access: How to open your Vaultek™ Safe.
Biometric Scanner: Personalized access for up to 20 unique ngerprints. See pages 08 to 11 for more
information.
Keypad: The numeric keypad responds quickly for rapid access and has a built-in proximity sensor that lights up
when your hand brushes against the safe. See page 06 for more information.
Vaultek App: Open the safe with the Bluetooth app. See pages 13 and 14 for more information.
Key: Two keys are provided for manual access to the safe in the event the battery dies.
Secure Defense: How your Vaultek™ Safes keeps people out.
Anti-Impact Latches: Built to withstand forceful impacts and heavy slams.
Unibody Construction: Our unibody design is extremely strong without welds or weak points.
No External Access Points: A combination of interior mounted hinges and anti-pry reinforcement bars help
prevent unwanted tools from attempting to break the safe open.
Security Sleep Mode: Activates when six (6) consecutive incorrect keypad entries are entered and does not
accept any entries for two minutes. If a button is pressed during this mode, all of the numbers will ash RED and
the alarm beeps. A backup key or programmed ngerprint may be used to open the safe.
ALWAYS check to make sure door has latched when closing; lid requires a rm press.
DO NOT get the ngerprint sensor area wet.
HOW-TO-VIDEOS AVAILABLE CLICK HERE FOR ACCESS
Battery Installation
To get started, insert one of your backup keys into the keyhole at the front of the safe (see Figure A). Push key in
and rotate the key 90 degrees clockwise to open the safe.
Remove crate foam insert. Locate the battery compartment door on the inside of the safe directly behind the '1'
key on the keypad (see Figure B).
Using the Phillips screwdriver provided open the battery cover by removing the single screw in the top center of
the battery cover.
Insert the 18650 rechargeable lithium-ion battery (included in box) into the battery compartment. Note that your
Vaultek™ safe automatically detects the polarity of the battery and can be installed in either direction.
When the battery is inserted you will hear a short welcome tone and the keypad will light up.
Once you hear the tone and see the keypad lights up, replace the battery cover and screw. You are now ready to
program your safe. See page 06.
4
5
6
Loading...